Text preview for : SONY DCR-SR68 985273632.pdf part of SONY DCR-SR58E/SR68/SR68E/ SR78E/SR88/SR88E DCR-SR58E/SR68/SR68E/
SR78E/SR88/SR88E service manual level 1,2,3
Back to : DCR-SR68.part1.rar | Home
DCR-SR58E/SR68/SR68E/ 985273632.pdf
SR78E/SR88/SR88E
Revision History
S.M. Rev.
SERVICE MANUAL
Ver. Date History Contents
issued
LEVEL 2 1.0 2010.01 Official Release -- --
1.1 2010.01 Revised-1 · Correction of Accessories Yes
Ver. 1.1 2010.01 US Model (A1 09-388) S. M. Revised: Page 2-8
Canadian Model
Revised-1 AEP Model
Replace the previously issued
UK Model
SERVICE MANUAL 9-852-736-31 North European Model
with this Manual.
E Model
Australian Model
Hong Kong Model
Chinese Model
Korea Model
Argentine Model
Photo: DCR-SR68/SILVER
Brazilian Model
SERVICE NOTE (Check the following note before the service.)
1-1. POWER SUPPLY DURING REPAIRS
1-2. PRECAUTION ON REPLACING THE VC-587 BOARD
1-3. USING SERVICE JIG
1-4. SELF-DIAGNOSIS FUNCTION
DIGITAL VIDEO CAMERA RECORDER
The components identified Les composants identifiés par une
by mark 0 or dotted line with marque 0 sont critiques pour la
mark 0 are critical for safety. sécurité.
Replace only with part number Ne les remplacer que par une
specified. pièce portant le numéro spécifié.
2010A0800-1
DCR-SR58E/SR68/SR68E/SR78E/SR88/SR88E_L2 © 2010.01
9-852-736-32 Sony EMCS Co. Published by Tokai TEC
These specifications are extracted from instruction manual of These specifications are extracted from instruction manual of
DCR-SR58E/SR68E/SR78E/SR88E. DCR-SR68/SR88.
ENGLISH ENGLISH
SPECIFICATIONS SPECIFICATIONS
System Input/Output connectors AC Adaptor AC-L200C/AC-L200D System Input/Output connectors AC Adaptor AC-L200C/AC-L200D
Signal format: PAL color, CCIR standards A/V Remote Connector: Video/audio output Power requirements: AC 100 V - 240 V, Signal format: NTSC color, EIA standards A/V Remote Connector: Video/audio output Power requirements: AC 100 V - 240 V,
Movie recording format: jack 50 Hz/60 Hz Movie recording format: jack 50 Hz/60 Hz
Video: MPEG-2 PS USB jack: mini-AB Current consumption: 0.35 A - 0.18 A Video: MPEG-2 PS USB jack: mini-AB Current consumption: 0.35 A - 0.18 A
Audio recording system: (DCR-SR58E/SR78E: output only) Power consumption: 18 W Audio recording system: Power consumption: 18 W
Dolby Digital 2ch Output voltage: DC 8.4 V* Dolby Digital 2ch LCD screen Output voltage: DC 8.4 V*
Dolby Digital Stereo Creator LCD screen Operating temperature: 0 °C to 40 °C Dolby Digital Stereo Creator Picture: 6.7 cm (2.7 type, aspect ratio 16:9) Operating temperature: 0 °C to 40 °C
Photo file format Picture: 6.7 cm (2.7 type, aspect ratio 16:9) (32 °F to 104 °F) Photo file format Total number of pixels: 230 400 (960 × 240) (32 °F to 104 °F)
: DCF Ver.2.0 Compatible Total number of pixels: 230 400 (960 × 240) Storage temperature: 20 °C to + 60 °C : DCF Ver.2.0 Compatible Storage temperature: 20 °C to + 60 °C
: Exif Ver.2.21 Compatible (4 °F to +140 °F) : Exif Ver.2.21 Compatible General (4 °F to +140 °F)
: MPF Baseline Compatible General Dimensions (approx.): 48 × 29 × 81 mm : MPF Baseline Compatible Power requirements: DC 6.8 V/7.2 V (battery Dimensions (approx.): 48 × 29 × 81 mm (1 15/16
Recording media (Movie/Photo) Power requirements: DC 6.8 V/7.2 V (battery (1 15/16 × 1 3/16 × 3 1/4 in.) (w/h/d) excluding Recording media (Movie/Photo) pack) DC 8.4 V (AC Adaptor) × 1 3/16 × 3 1/4 in.) (w/h/d) excluding the
Internal hard disk pack) DC 8.4 V (AC Adaptor) the projecting parts Internal hard disk Average power consumption: During camera projecting parts
DCR-SR58E/SR68E: 80 GB Average power consumption: During camera Mass (approx.): 170 g (6.0 oz) excluding the DCR-SR68: 80 GB recording, using LCD screen at normal Mass (approx.): 170 g (6.0 oz) excluding the
DCR-SR78E/SR88E: 120 GB recording, using LCD screen at normal power cord (mains lead) DCR-SR88: 120 GB brightness: 2.0 W power cord (mains lead)
"Memory Stick PRO Duo" media brightness: 2.0 W * See the label on the AC Adaptor for other "Memory Stick PRO Duo" media Operating temperature: 0 °C to 40 °C
SD memory card, SDHC memory card (Class Operating temperature: 0 °C to 40 °C specifications. SD memory card, SDHC memory card (Class (32 °F to 104 °F) * See the label on the AC Adaptor for other
2, 4, 6, 10) (32 °F to 104 °F) 2, 4, 6, 10) Storage temperature: 20 °C to + 60 °C specifications.
When measuring media capacity, 1 GB equals Storage temperature: 20 °C to + 60 °C Rechargeable battery pack NP-FV30 When measuring media capacity, 1 GB equals (4 °F to +140 °F)
1 billion bytes, a portion of which is used for (4 °F to +140 °F) Maximum output voltage: DC 8.4 V 1 billion bytes, a portion of which is used for Dimensions (approx.) Rechargeable battery pack NP-FV30
system management and/or application files. Dimensions (approx.) Output voltage: DC 7.2 V system management and/or application files. 56 × 65 × 107 mm (2 1/4 × 2 5/8 × 4 1/4 in.) Maximum output voltage: DC 8.4 V
The capacity that a user can use is below. 56 × 65 × 107 mm (2 1/4 × 2 5/8 × 4 1/4 in.) Maximum charge voltage: DC 8.4 V The capacity that a user can use is below. (w/h/d) including the projecting parts Output voltage: DC 7.2 V
DCR-SR58E/SR68E: Approx. 79.3 GB (w/h/d) including the projecting parts Maximum charge current: 2.12 A DCR-SR68: Approx. 79.3 GB 56 × 65 × 115 mm (2 1/4 × 2 5/8 × 4 5/8 in.) Maximum charge voltage: DC 8.4 V
DCR-SR78E/SR88E: Approx. 119 GB 56 × 65 × 115 mm (2 1/4 × 2 5/8 × 4 5/8 in.) Capacity DCR-SR88: Approx. 119 GB (w/h/d) including the projecting parts, Maximum charge current: 2.12 A
Image device (w/h/d) including the projecting parts, typical: 3.6 Wh (500 mAh) Image device and the supplied rechargeable battery pack Capacity
2.25 mm (1/8 type) CCD (Charge Coupled and the supplied rechargeable battery pack minimum: 3.6 Wh (500 mAh) 2.25 mm (1/8 type) CCD (Charge Coupled attached typical: 3.6 Wh (500 mAh)
Device) attached Type: Li-ion Device) Mass (approx.) minimum: 3.6 Wh (500 mAh)
Gross: Approx. 800 000 pixels Mass (approx.) Gross: Approx. 680 000 pixels 280 g (9 oz) main unit only Type: Li-ion
Effective (Movie, 16:9): Approx. 280 g (9 oz) main unit only Design and specifications of your camcorder and Effective (Movie, 16:9): Approx. 410 000 320 g (11 oz) including the supplied
490 000 pixels 320 g (11 oz) including the supplied accessories are subject to change without notice. pixels rechargeable battery pack Design and specifications of your camcorder and
Effective (Photo, 16:9): Approx. 310 000 rechargeable battery pack · Manufactured under license from Dolby Effective (Photo, 16:9): Approx. 250 000 accessories are subject to change without notice.
pixels Laboratories. pixels · Manufactured under license from Dolby
Effective (Photo, 4:3): Approx. 410 000 pixels Effective (Photo, 4:3): Approx. 340 000 pixels Laboratories.
Lens Lens
Carl Zeiss Vario-Tessar Carl Zeiss Vario-Tessar
60 × (Optical), 2 000 × (Digital) 60 × (Optical), 2 000 × (Digital)
DCR-SR58E/SR68E/SR78E/SR88E Filter diameter: 30 mm (1 3/16 in.)
Filter diameter: 30 mm (1 3/16 in.) F1.8 to 6.0
F1.8 to 6.0 Focal length:
Focal length: f=1.8 to 108 mm (3/32 to 4 3/8 in.)
f=1.8 to 108 mm (3/32 to 4 3/8 in.) When converted to a 35 mm still camera
When converted to a 35 mm still camera For movies: 39 to 2 340 mm (1 9/16 to
For movies: 39 to 2 340 mm (1 9/16 to 92 1/4 in.) (16:9)
92 1/4 in.) (16:9) For photos: 44 to 2 640 mm (1 3/4 to 104
For photos: 44 to 2 640 mm (1 3/4 to 104 in.) in.) (4:3)
(4:3) Color temperature: [AUTO], [ONE PUSH],
Color temperature: [AUTO], [ONE PUSH], [INDOOR] (3 200 K), [OUTDOOR]
[INDOOR] (3 200 K), [OUTDOOR] (5 800 K)
(5 800 K) Minimum illumination
Minimum illumination 3 lx (lux) ([AUTO SLW SHUTTR] is set to
3 lx (lux) ([AUTO SLW SHUTTR] is set to [ON],
[ON], shutter speed 1/30 second)
shutter speed 1/25 second)
DCR-SR58E/SR68/SR68E/SR78E/SR88/SR88E_L2
2
Model information table
Model DCR-SR58E DCR-SR68 DCR-SR68E DCR-SR78E DCR-SR88 DCR-SR88E
US, CND, E, CH, E, HK, US, CND, E,
Destination AEP, UK AEP, UK AEP, E
KR, AR, BR AUS, NE KR
Color system PAL NTSC PAL PAL NTSC PAL
HDD 80 GB 80 GB 80 GB 120 GB 120 GB 120 GB
CAM PC
Data
copy
CAM PC
· Abbreviation
AR : Argentine model
AUS : Australian model
BR : Brazilian model
CH : Chinese model
CND : Canadian model
HK : Hong Kong model
KR : Korea model
NE : North European model
DCR-SR58E/SR68/SR68E/SR78E/SR88/SR88E_L2
3
Caution
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Dispose of used batteries according to the instructions.
SAFETY-RELATED COMPONENT WARNING!! ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0 SUR LES
MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
PUBLISHED BY SONY. DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer.
1. Check the area of your repair for unsoldered or poorly-soldered Unleaded solder
connections. Check the entire board surface for solder splashes Boards requiring use of unleaded solder are printed with the leadfree
and bridges. mark (LF) indicating the solder contains no lead.
2. Check the interboard wiring to ensure that no wires are "pinched" (Caution: Some printed circuit boards may not come printed with
or contact high-wattage resistors. the lead free mark due to their particular size.)
3. Look for unauthorized replacement parts, particularly transistors,
that were installed during a previous repair. Point them out to
the customer and recommend their replacement. : LEAD FREE MARK
4. Look for parts which, through functioning, show obvious signs Unleaded solder has the following characteristics.
of deterioration. Point them out to the customer and recommend · Unleaded solder melts at a temperature about 40°C higher than
their replacement. ordinary solder.
5. Check the B+ voltage to see it is at the values specified. Ordinary soldering irons can be used but the iron tip has to be
6. Flexible Circuit Board Repairing applied to the solder joint for a slightly longer time.
· Keep the temperature of the soldering iron around 270°C Soldering irons using a temperature regulator should be set to
during repairing. about 350°C.
· Do not touch the soldering iron on the same conductor of the Caution: The printed pattern (copper foil) may peel away if the
circuit board (within 3 times). heated tip is applied for too long, so be careful!
· Be careful not to apply force on the conductor when soldering · Strong viscosity
or unsoldering. Unleaded solder is more viscous (sticky, less prone to flow) than
ordinary solder so use caution not to let solder bridges occur such
as on IC pins, etc.
· Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
DCR-SR58E/SR68/SR68E/SR78E/SR88/SR88E_L2
1. SERVICE NOTE
ENGLISH
1-1. POWER SUPPLY DURING REPAIRS 1-4. SELF-DIAGNOSIS FUNCTION
In this unit, about 10 seconds after power is supplied to the battery terminal using the regulated power supply (8.4 V), the power is shut off 1-4-1. Self-diagnosis Function 1-4-2. Self-diagnosis Display
so that the unit cannot operate. When problems occur while the unit is operating, the self-diagnosis When problems occur while the unit is operating, the counter of the
These following method is available to prevent this. function starts working, and displays on the LCD screen what to LCD screen shows a 4-digit display consisting of an alphabet and
do. This function consists of two display; self-diagnosis display and numbers, which blinks at 3.2 Hz. This 5-character display indicates
Method: service mode display. the "repaired by:", "block" in which the problem occurred, and
Use the AC power adaptor. Details of the self-diagnosis functions are provided in the Instruc- "detailed code" of the problem.
tion manual.
1-2. PRECAUTION ON REPLACING THE VC-587 BOARD LCD screen
C:31:11
Turn on the set and establish a USB connection , save the USB serial data before replacing the board.
DESTINATION DATA
When you replace to the repairing board, the written destination data of repairing board also might be changed to original setting.
Blinks at 3.2Hz
Start the Adjust Manual in the Adjust Station and execute the "DESTINATION DATA WRITE".
After the board replacement, the error of the built-in recording media may be displayed.
In this case, execute the [DESTINATION DATA WRITE] then the error will be cleared.
If it is not cleared with [DESTINATION DATA WRITE], format the built-in recording media.
USB SERIAL SAVE C 31 11
When you replace to the repairing board, get the data from the former one.
Start the Adjust Manual in the Adjust Station and perform "USB SERIAL SAVE" to get the data.
Repaired by: Block Detailed Code
USB SERIAL No. C : Corrected by customer Indicates the appropriate Refer to "1--3. Self-diagnosis Code Table".
The set is shipped with a unique ID (USB Serial No.) written in it. H : Corrected by dealer step to be taken.
E : Corrected by service E.g.
This ID has not been written in a new board for service, and therefore it must be entered after the board replacement. engineer 31 ....Reload the tape.
Start the Adjust Manual in the Adjust Station and execute the "USB SERIAL No. INPUT". 32 ....Turn on power again.
1-4-3. Self-diagnosis Code Table
1-3. USING SERVICE JIG
Self-diagnosis Code
Connect the extension cable (J-6082-578-A) between CN4003 on the DA-049 board and CN1001 on the VC-587 board.
Repaired by:
DA-09 board (side A) Block Detailed Symptom/State Correction
Function Code
CN003 C 0 4 0 0 Non-standard battery is used. Use the InfoLITHIUM battery.
Memory card is unformatted. Format the memory card.
C 1 3 0 1
Memory card is broken. Insert a new memory card.
Remove the power source. Reconnect it again and operate
C 1 3 0 2 Disc access error
your camcorder again.
Extension cable (100P) E 2 0 0 0 Flash memory data are rewritten. Make flash memory data correct value. (Note)
(J-6082-578-A)
Inspect the lens block focus reset sensor (pin 8 of CN5401 on
the VC-587 board) when focusing is performed when the focus
Difficult to adjust focus
E 6 1 0 0 buttons of the touch panel are pressed in the focus manual mode,
(Cannot initialize focus.)
and the focus motor drive circuit (IC5401 on the VC-587 board)
when the focusing is not performed.
CN1001 Inspect the lens block zoom MR sensor (pin 0 of CN5401 on
Zoom operations fault the VC-587 board) when zooming is performed when the zoom
E 6 1 1 0
(Cannot initialize zoom lens.) lever is operated, or the zoom motor drive circuit (IC5401 on
the VC-587 board) when zooming is not performed.
VC-587 board (side B) The abnormalities in initialization of
the focus lens and the abnormalities in
E 6 1 1 1 Check both C: 61: 00 and E: 61: 10 of the self-diagnosis code.
initialization of the zoom lens occurred
simultaneously.
Fault of writing or erasing the flash
E 9 4 0 0 Inspect the flash memory (IC7801 on the VC-587 board).
memory
E 9 4 0 1 Internal flash memory fault Inspect the flash memory (IC7801 on the VC-587 board).
Note: Start the Adjust Manual in the Adjust Station and refer to the "Destination data write".
DCR-SR58E/SR68/SR68E/SR78E/SR88/SR88E_L2
1-1E
2. REPAIR PARTS LIST
IDENTIFYING PARTS
(ENGLISH)
Follow the disassembly in the numerical order given. NOTE:
· -XX, -X mean standardized parts, so they may have some
The components identified by mark 0
differencesfromtheoriginalone. ordottedlinewithmark0arecriticalfor
· Itemsmarked"*"arenotstockedsincetheyareseldomrequired safety.
forroutineservice.Somedelayshouldbeanticipatedwhen Replaceonlywithpartnumberspecified.
orderingtheseitems.
Lescomposantsidentifiésparunemarque
· Themechanicalpartswithnoreferencenumberintheexploded
0sontcritiquespourlasécurité.
viewsarenotsupplied.
Nelesremplacerqueparunepiècepor-
· Duetostandardization,replacementsinthepartslistmaybe tantlenumérospécifié.
differentfromthepartsspecifiedinthediagramsorthecom-
5 Top Cabinet Section ponentsusedontheset. · Color Indication of Appearance Parts
Example:
(SILVER) : Cabinet's Color
(Silver) : Parts Color
· Abbreviation
AR : Argentine model
1 HDD Lid AUS : Australian model View Position
BR : Brazilian model Top View
2 HDD CH : Chinese model
CND : Canadian model Left View
HK : Hong Kong model Back View
3 HDD Holder q; VC-587 Board 8 BT Panel Section KR : Korea model
7
-58 · MS-432 Board NE : North European model
VC
· FP-1216 Flexible Board
9
qa DA-049 Board
-04
DA
9 Lens/Chassis Section
· CD-786 Board Front View Right View
· FP-1168 Flexible Board
Bottom View
Main Frame Assy
6 F Panel Assy
7 Cabinet R Section
[Disassembly]
4 Bottom Cabinet [Exploded View]
· PD-404 Board
· OC-024 Board
· FP-1239 Flexible Board
Link ACCESSORIES
AC- DIS-ASSEMBLY
DCR-SR58E/SR68/SR68E/SR78E/SR88/SR88E_L2
2-
NOTE FOR REPAIR
· Make sure that the flat cable and flexible board are not cracked Cut and remove the part of gilt
of bent at the terminal. which comes off at the point.
Do not insert the cable insufficiently nor crookedly. (Be careful or some
pieces of gilt may be left inside)
· When remove a connector, don't pull at wire of connector. It is
possible that a wire is snapped.
· When installing a connector, don't press down at wire of con-
nector.
It is possible that a wire is snapped.
· Do not apply excessive load to the gilded flexible board.
DCR-SR58E/SR68/SR68E/SR78E/SR88/SR88E_L2
2-2
2-1. EXPLODED VIEWS DISASSEMBLY
2-1-1. HDD SECTION 1. Remove to numerical order (1 to 3) in the left figure.
1 #2 / #10 X 4
#2
2 #10
#2
#10
(Note 1) #2
11 3
#10
(Note 2)
3 #2 / #10 X 2
#2
Top Cabinet Section
(See page 2-4)
24 5
#2 #2
#10
(Note 1)
Screw Note
5
#10: M1.7 X 4.0
3
#2: M1.7 X 4.0
(Silver)
Note 1:
(Black)
(Note 2) 2-635-562-31 2-599-475-31
THE COMBINATION OF CABINET'S
COLOR AND SCREW
1.7 1.7
36 The screw pointed is different according to the cabinet's color.
For the combination of cabinet's color and screw, please refer to Table 2-1.
4.0 4.0
7
Table 2-1
Screw's
Cabinet's Color
Ref. No. (Parts Color.)
#10 (Silver) SILVER
Ref. No. Part No. Description Ref. No. Part No. Description
#2 (Black) RED/BLUE
1 4-155-772-01 LID (327), HDD (SR58E/SR68 (SILVER)/SR68E 6 4-155-771-01 HOLDER (327), HDD (SR58E/SR68 (SILVER)/
(SILVER)/SR78E/SR88/SR88E) SR68E (SILVER)/SR78E/SR88/SR88E)
1 4-155-772-11 LID (327), HDD (SR68 (RED)/SR68E (RED)) 6 4-155-771-11 HOLDER (327), HDD (SR68 (RED)/SR68E (RED)/
1 4-155-772-21 LID (327), HDD (SR68 (BLUE)/SR68E (BLUE)) SR68 (BLUE)/SR68E (BLUE)) Note 2: Direction of installation of 10 Style Damper B (1) as shown in the
2 X-2515-196-1 COVER ASSY (327), DC (SR58E/SR68(SILVER)/ 7 X-2515-197-1 COVER ASSY (327), AV JACK (SR58E/SR68 figure.
SR68E (SILVER)/SR78E/SR88/SR88E) (SILVER)/SR68E (SILVER)/SR78E/SR88/SR88E)
2 X-2541-585-1 COVER ASSY (327, R), DC (SR68 (RED)/ 7 X-2541-583-1 COVER ASSY (327, R), AV JACK (SR68 (RED)/
SR68E (RED)) SR68E (RED))
7 X-2541-584-1 COVER ASSY (327, L), AV JACK (SR68 (BLUE)/
2 X-2541-586-1 COVER ASSY (327, L), DC (SR68 (BLUE)/ SR68E (BLUE))
SR68E (BLUE))
3 4-157-242-01 DAMPER B (1), 10STYLE (Note 2) #2 2-635-562-31 SCREW (M1.7) (Note 1)
4 1-840-366-21 HDD (MK8034GAL-80GB) _MASSPRO (SR58E/ #10 2-599-475-31 SCREW (M1.7) (Note 1)
SR68/SR68E)
4 1-840-367-21 HDD (MK1234GAL-120GB) _MASSPRO (SR78E/
SR88/SR88E)
5 4-134-206-01 GASKET (OG)
DCR-SR58E/SR68/SR68E/SR78E/SR88/SR88E_L2
2-3
2-1-2. TOP CABINET SECTION
DISASSEMBLY
5 57 1. Remove to numerical order (4 to 7) in the left figure.
4 #2 / #10 X 2
Bottom View
#2/#10
MIC901
SP901
55
56 5 #2 / #10 X 4 #12 X 1
Left View Right View Bottom View
#2/#10 #2/#10
#12
#11
54
#2 #12 6 #2 X 3
#10 BT Panel Section
(Note) (See page 2-5) Right View Top View Left View #2
#2 7 Cabinet R Section #2
(See page 2-7)
#2
#2
#2 #10 7 #2 / #10 X 2
(Note)
Right View
53
#2
#10
(Note)
Note
4 52
#2
#10 #2/#10 Note
6 51 (Boss) #2 (Note) #2
#10
#2/#10
THE COMBINATION OF CABINET'S
(Note) Screw
COLOR AND SCREW
Ref. No. Part No. Description Ref. No. Part No. Description #2: M1.7 X 4.0 #10: M1.7 X 4.0 The screw pointed is different according to the cabinet's color.
(Black) (Silver)
51 A-1750-485-A PANEL ASSY (327), F (SR58E/SR68 (SILVER)/ 57 A-1750-490-A CABINET ASSY (327), TOP (SR58E/SR68 2-635-562-31 2-599-475-31
For the combination of cabinet's color and screw, please refer to Table 2-1.
SR68E (SILVER)/SR78E/SR88/SR88E) (SILVER)/SR68E (SILVER)/SR78E/SR88/SR88E)
51 A-1750-486-A PANEL ASSY (327, R), F (SR68 (RED)/SR68E 57 A-1750-491-A CABINET ASSY (327, R), TOP (SR68 (RED)/SR68E
(RED)) (RED)) 1.7 1.7