Text preview for : MFL30105501_0.pdf part of LG 27LZ55 SERVICE MANUAL



Back to : MFL30105501_0.pdf | Home

website:http://biz.LGservice.com e-mail:http://www.LGEservice.com/techsup.html

LCD TV SERVICE MANUAL
CHASSIS : ML-041A

MODEL RZ-27LZ55
CAUTION
BEFORE SERVICING THE CHASSIS, READ THE SAFETY PRECAUTIONS IN THIS MANUAL.

CONTENTS

CONTENTS .............................................................................................. 2 PRODUCT SAFETY ..................................................................................3 SPECIFICATION ........................................................................................6 ADJUSTMENT INSTRUCTION ...............................................................10 TROUBLE SHOOTING ............................................................................15 BLOCK DIAGRAM...................................................................................20 WIRING DIAGRAM ..................................................................................22 EXPLODED VIEW .................................................................................. 23 EXPLODED VIEW PARTS LIST ..............................................................24 REPLACEMENT PARTS LIST ............................................................... 25 SVC. SHEET ...............................................................................................

-2-

SAFETY PRECAUTIONS
IMPORTANT SAFETY NOTICE
Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in the Schematic Diagram and Replacement Parts List. It is essential that these special safety parts should be replaced with the same components as recommended in this manual to prevent Shock, Fire, or other Hazards. Do not modify the original design without permission of manufacturer.

General Guidance
An isolation Transformer should always be used during the servicing of a receiver whose chassis is not isolated from the AC power line. Use a transformer of adequate power rating as this protects the technician from accidents resulting in personal injury from electrical shocks. It will also protect the receiver and it's components from being damaged by accidental shorts of the circuitry that may be inadvertently introduced during the service operation. If any fuse (or Fusible Resistor) in this TV receiver is blown, replace it with the specified. When replacing a high wattage resistor (Oxide Metal Film Resistor, over 1W), keep the resistor 10mm away from PCB. Keep wires away from high voltage or high temperature parts.

Leakage Current Hot Check (See below Figure)
Plug the AC cord directly into the AC outlet. Do not use a line Isolation Transformer during this check. Connect 1.5K/10watt resistor in parallel with a 0.15uF capacitor between a known good earth ground (Water Pipe, Conduit, etc.) and the exposed metallic parts. Measure the AC voltage across the resistor using AC voltmeter with 1000 ohms/volt or more sensitivity. Reverse plug the AC cord into the AC outlet and repeat AC voltage measurements for each exposed metallic part. Any voltage measured must not exceed 0.75 volt RMS which is corresponds to 0.5mA. In case any measurement is out of the limits specified, there is possibility of shock hazard and the set must be checked and repaired before it is returned to the customer.

Leakage Current Hot Check circuit

AC Volt-meter

Before returning the receiver to the customer,
always perform an AC leakage current check on the exposed metallic parts of the cabinet, such as antennas, terminals, etc., to be sure the set is safe to operate without damage of electrical shock.
Good Earth Ground such as WATER PIPE, CONDUIT etc.

To Instrument's exposed METALLIC PARTS

0.15uF

Leakage Current Cold Check(Antenna Cold Check)
With the instrument AC plug removed from AC source, connect an electrical jumper across the two AC plug prongs. Place the AC switch in the on position, connect one lead of ohm-meter to the AC plug prongs tied together and touch other ohm-meter lead in turn to each exposed metallic parts such as antenna terminals, phone jacks, etc. If the exposed metallic part has a return path to the chassis, the measured resistance should be between 1M and 5.2M. When the exposed metal has no return path to the chassis the reading must be infinite. An other abnormality exists that must be corrected before the receiver is returned to the customer.

1.5 Kohm/10W

SERVICING PRECAUTIONS
CAUTION: Before servicing receivers covered by this service manual and its supplements and addenda, read and follow the SAFETY PRECAUTIONS on page 3 of this publication. NOTE: If unforeseen circumstances create conflict between the following servicing precautions and any of the safety precautions on page 3 of this publication, always follow the safety precautions. Remember: Safety First. General Servicing Precautions 1. Always unplug the receiver AC power cord from the AC power source before; a. Removing or reinstalling any component, circuit board module or any other receiver assembly. b. Disconnecting or reconnecting any receiver electrical plug or other electrical connection. c. Connecting a test substitute in parallel with an electrolytic capacitor in the receiver. CAUTION: A wrong part substitution or incorrect polarity installation of electrolytic capacitors may result in an explosion hazard. 2. Test high voltage only by measuring it with an appropriate high voltage meter or other voltage measuring device (DVM, FETVOM, etc) equipped with a suitable high voltage probe. Do not test high voltage by "drawing an arc". 3. Do not spray chemicals on or near this receiver or any of its assemblies. 4. Unless specified otherwise in this service manual, clean electrical contacts only by applying the following mixture to the contacts with a pipe cleaner, cotton-tipped stick or comparable non-abrasive applicator; 10% (by volume) Acetone and 90% (by volume) isopropyl alcohol (90%-99% strength) CAUTION: This is a flammable mixture. Unless specified otherwise in this service manual, lubrication of contacts in not required. 5. Do not defeat any plug/socket B+ voltage interlocks with which receivers covered by this service manual might be equipped. 6. Do not apply AC power to this instrument and/or any of its electrical assemblies unless all solid-state device heat sinks are correctly installed. 7. Always connect the test receiver ground lead to the receiver chassis ground before connecting the test receiver positive lead. Always remove the test receiver ground lead last. 8. Use with this receiver only the test fixtures specified in this service manual. CAUTION: Do not connect the test fixture ground strap to any heat sink in this receiver. Electrostatically Sensitive (ES) Devices Some semiconductor (solid-state) devices can be damaged easily by static electricity. Such components commonly are called Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and semiconductor "chip" components. The following techniques should be used to help reduce the incidence of component damage caused by static by static electricity. 1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any electrostatic charge on your body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging wrist strap device, which should be removed to prevent potential shock reasons prior to applying power to the unit under test. 2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as aluminum foil, to prevent electrostatic charge buildup or exposure of the assembly. 3. Use only a grounded-tip soldering iron to solder or unsolder ES devices. 4. Use only an anti-static type solder removal device. Some solder removal devices not classified as "anti-static" can generate electrical charges sufficient to damage ES devices. 5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices. 6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or comparable conductive material). 7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material to the chassis or circuit assembly into which the device will be installed. CAUTION: Be sure no power is applied to the chassis or circuit, and observe all other safety precautions. 8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity sufficient to damage an ES device.) General Soldering Guidelines 1. Use a grounded-tip, low-wattage soldering iron and appropriate tip size and shape that will maintain tip temperature within the range or 500 F to 600 F. 2. Use an appropriate gauge of RMA resin-core solder composed of 60 parts tin/40 parts lead. 3. Keep the soldering iron tip clean and well tinned. 4. Thoroughly clean the surfaces to be soldered. Use a mall wirebristle (0.5 inch, or 1.25cm) brush with a metal handle. Do not use freon-propelled spray-on cleaners. 5. Use the following unsoldering technique a. Allow the soldering iron tip to reach normal temperature. (500 F to 600 F) b. Heat the component lead until the solder melts. c. Quickly draw the melted solder with an anti-static, suctiontype solder removal device or with solder braid. CAUTION: Work quickly to avoid overheating the circuitboard printed foil. 6. Use the following soldering technique. a. Allow the soldering iron tip to reach a normal temperature (500 F to 600 F) b. First, hold the soldering iron tip and solder the strand against the component lead until the solder melts. c. Quickly move the soldering iron tip to the junction of the component lead and the printed circuit foil, and hold it there only until the solder flows onto and around both the component lead and the foil. CAUTION: Work quickly to avoid overheating the circuit board printed foil. d. Closely inspect the solder area and remove any excess or splashed solder with a small wire-bristle brush.

-4-

IC Remove/Replacement Some chassis circuit boards have slotted holes (oblong) through which the IC leads are inserted and then bent flat against the circuit foil. When holes are the slotted type, the following technique should be used to remove and replace the IC. When working with boards using the familiar round hole, use the standard technique as outlined in paragraphs 5 and 6 above. Removal 1. Desolder and straighten each IC lead in one operation by gently prying up on the lead with the soldering iron tip as the solder melts. 2. Draw away the melted solder with an anti-static suction-type solder removal device (or with solder braid) before removing the IC. Replacement 1. Carefully insert the replacement IC in the circuit board. 2. Carefully bend each IC lead against the circuit foil pad and solder it. 3. Clean the soldered areas with a small wire-bristle brush. (It is not necessary to reapply acrylic coating to the areas). "Small-Signal" Discrete Transistor Removal/Replacement 1. Remove the defective transistor by clipping its leads as close as possible to the component body. 2. Bend into a "U" shape the end of each of three leads remaining on the circuit board. 3. Bend into a "U" shape the replacement transistor leads. 4. Connect the replacement transistor leads to the corresponding leads extending from the circuit board and crimp the "U" with long nose pliers to insure metal to metal contact then solder each connection. Power Output, Transistor Device Removal/Replacement 1. Heat and remove all solder from around the transistor leads. 2. Remove the heat sink mounting screw (if so equipped). 3. Carefully remove the transistor from the heat sink of the circuit board. 4. Insert new transistor in the circuit board. 5. Solder each transistor lead, and clip off excess lead. 6. Replace heat sink. Diode Removal/Replacement 1. Remove defective diode by clipping its leads as close as possible to diode body. 2. Bend the two remaining leads perpendicular y to the circuit board. 3. Observing diode polarity, wrap each lead of the new diode around the corresponding lead on the circuit board. 4. Securely crimp each connection and solder it. 5. Inspect (on the circuit board copper side) the solder joints of the two "original" leads. If they are not shiny, reheat them and if necessary, apply additional solder. Fuse and Conventional Resistor Removal/Replacement 1. Clip each fuse or resistor lead at top of the circuit board hollow stake. 2. Securely crimp the leads of replacement component around notch at stake top. 3. Solder the connections. CAUTION: Maintain original spacing between the replaced component and adjacent components and the circuit board to prevent excessive component temperatures.

Circuit Board Foil Repair Excessive heat applied to the copper foil of any printed circuit board will weaken the adhesive that bonds the foil to the circuit board causing the foil to separate from or "lift-off" the board. The following guidelines and procedures should be followed whenever this condition is encountered. At IC Connections To repair a defective copper pattern at IC connections use the following procedure to install a jumper wire on the copper pattern side of the circuit board. (Use this technique only on IC connections). 1. Carefully remove the damaged copper pattern with a sharp knife. (Remove only as much copper as absolutely necessary). 2. carefully scratch away the solder resist and acrylic coating (if used) from the end of the remaining copper pattern. 3. Bend a small "U" in one end of a small gauge jumper wire and carefully crimp it around the IC pin. Solder the IC connection. 4. Route the jumper wire along the path of the out-away copper pattern and let it overlap the previously scraped end of the good copper pattern. Solder the overlapped area and clip off any excess jumper wire. At Other Connections Use the following technique to repair the defective copper pattern at connections other than IC Pins. This technique involves the installation of a jumper wire on the component side of the circuit board. 1. Remove the defective copper pattern with a sharp knife. Remove at least 1/4 inch of copper, to ensure that a hazardous condition will not exist if the jumper wire opens. 2. Trace along the copper pattern from both sides of the pattern break and locate the nearest component that is directly connected to the affected copper pattern. 3. Connect insulated 20-gauge jumper wire from the lead of the nearest component on one side of the pattern break to the lead of the nearest component on the other side. Carefully crimp and solder the connections. CAUTION: Be sure the insulated jumper wire is dressed so the it does not touch components or sharp edges.

-5-

SPECIFICATION
NOTE : Specifications and others are subject to change without notice for improvement.

1. Application range
This specification is applied to ML-041A chassis.

2. Requirement for Test
Testing for standard of each part must be followed in below condition. (1) Temperature: 25°C ± 2°C (2) Humidity: 65% ± 10% (3) Power: Standard input voltage (AC 100-240V, 50/60Hz) (4) Measurement must be performed after heat-run more than 30min. (5) Adjusting standard for this chassis is followed a special standard.

3.General Specification(TV)
No 1. 2. Item Video input applicable system Receivable Broadcasting System Specification PAL-D/K, B/G, I, NTSC-M, SECAM NTSC 4.43 1) PAL/SECAM BG 2) PAL/SECAM DK 3) PAL I/I 4) SECAM L/L' 5) NTSC M 6) PAL-N/M 7) NTSC M 3. RF Input Channel VHF : E2 ~ E12 UHF : E21 ~ E69 CATV : S1 ~ S20 HYPER : S21~ S41 L/L' : B, C, D VHF : 2~13 UHF : 14~69 CATV : 1~125 VHF Low : 1 ~ M10 VHF High : 4~S22 UHF : S23~62 4. 5. 6. 7. 8. 9. 10. Input Voltage Market Picture Size Tuning System Operating Environment Storage Environment Display AC 100 ~ 240 V/50Hz, 60Hz Worldwide 685.8 mm FVS 100 program FS 1) Temp : 0 ~ 40 deg 2) Humidity : 85 % 3) Temp : -20 ~ 60 deg 4) Humidity : 85 % LCD Module CMO 27 inch PAL,200 PR.(Option) NTSC JAPAN NTSC FRANCE PAL 6),7) South America Market 7) Except South America NTSC Market (RM) (RZ/RT) EU/Non-EU (PAL Market) Remark

-6-

4. General Specification
NO 1 2 Panel Frequency range Item Specification 27" TFT WXGA LCD H : 31 ~ 48.363Khz V : 50 ~ 60Hz 3 Control Function 1) Contrast/Brightness 2) H-Position / V-Position 3) Tracking : Clock / Phase 4) Auto Configure 5) Reset 4 Comoponent Jack 1:Y 3 : Pb 5 : Pr 7 : Line1 Ready 9 : LINE2 11: LINE3 13: Line3 Ready D4 Jack (525i,525p,750p,1125i) 2 : Y GND 4 : Pb GND 6 : Pr GND 8 : LINE1 10:Line2 Ready 12:SWITCH GND 14: SWITCH 7 Power ON Stand by DPMS Mode Power off 8 LCD Module H/V-Sync ON/ON OFF/ON ON/OFF Type Size Pixel Pitch Pixel Format Video Active OFF OFF LPL LPL Power consumption max 170W 3.0W typ. 25W 637.55 x 379.8 x 40.7 0.1455(H) x 0.4365(V) W W W W mm mm LED Green Red Green *. (H) x (V) x (D) JAPAN Only Middle east / NTSC Area DVI-I input Unit Remark

1366 horiz. By 768 vert. Pixels RGB strip arrangement

Coating

Hard coating(3H), Anti-glare treatment of the front polarizer,

Back Light

CMO

CCFL

-7-

5. Optical Feature(LCD Module)
No Item Specification LPL 1 2 Viewing Angle Luminance R/L, U/D Luminance (cd/m2) Variation 3 4 Contrast Ratio CIE Color Coordinates White Xw Yw RED Xr Yr Green Xg Yg Blue Xb Yb Typ. Typ. Typ. Typ. Typ. Typ. Typ. Typ. 1000 0.285 0.293 0.6452 0.331 0.276 0.597 0.143 0.066 176,176 550 1.3 Typical MAX / MIN All white / All black CMO Remark

6.Feature and Function
No 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24 25 Teletext REMOCON AV Input S-AV Input Component input PERI TV Connector PERI TV Connector RGB Input RS-232 Discrete IR D-Sub Audio Input 2 Carrier Stereo NICAM Stereo 2 Carrier Dual NICAM Dual DW(Double Window) Mode MW(Multi Window) Mode Film Mode Noise Reduction Progressive Scan Motion Detection SRS WOW Swivel Speaker Ez-pip Local key Item Specification TOP, FLOF NEC Code 1 1 2 1 Half SCART : 1 Full SCART : 1 1 1 1 1 BG, DK BG, I, LL' BG, DK BG, I, LL' X X 0 X 0 0 X X X Pr+/-, vol+/-, ok, menu, tv/av, power Top(option) PAL/ NTSC Rear(RT/RM) Side Side, Rear (RT/RM), Side RZ(HD) Rear (RZ) Rear (RZ) DVI D-sub 9 pin (RM) (RM) Stereo Remark

-8-

7. Component Video Input(Y, PB, PR)
No Resolution 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 640x480 640x480 704x480 720x576 720x576 1280x720 1280x720 1280x720 1920x1080 1920x1080 1920x1080 Specification H-freq(kHz) 15.73 15.63 31.47 15.625 31.25 45.00 44.96 37.5 31.25 -> 28.125 33.75 33.72 60 59.94 59.94 50.00 50.00 60.00 59.94 50.00 50.00 60.00 59.94 V-freq(Hz) SDTV, DVD 480i SDTV, DVD 480i EDTV 480p SDTV, DVD 625 Line HDTV 576p HDTV 720p HDTV 720p HDTV 720p 50HZ RZ, RT, RM RZ, RT, RM RT, RM RZ, RT RT, RZ RT, RM, RZ RT, RM, RZ RT, RZ Proposed

HDTV 1080i 50Hz (Only AU) RT, RZ HDTV 1080i 60Hz (ATSC) HDTV 1080i 59.94Hz RT, RM, RZ RT, RM, RZ

Input Side Comp 480i(RZ, RT, RM), 576I(RZ, RT), 720P_1080i(RZ55 Model Only)

8. PC Input Mode
No Resolution H-freq(kHz) V-freq.(Hz) Pixel clock(MHz) Proposed

DVI-PC, Analog RGB, Digital RGB 1 2 3 4 5 6 7 640x480 800x600 1024x768 1280x768 1360x768 1280x720 1920x1080 31.469 37.879 48.363 47.693 47.649 45.00 33.75 59.94 60.31 60.00 60.00 59.936 60.00 60.00 25.17 40.00 65.00 80.125 84.625 74.375 86.375 VESA(VGA) VESA(SVGA) VESA(XGA) VESA(WXGA) VESA(WXGA) HDCP DVI Digital 720p (RM only) HDCP DVI Digital 1080i(RM only)

-9-

ADJUSTMENT INSTRUCTION
1. Application
This document is applied to 23", 26", 27", 32" Wide LCD TV which is manufactured in Monitor Factory or is produced on the basis of this data. 3.2.5 Screen Adjustment Instructions
Adjustment Content 1 Mode Select CMD(ASCII) VALUE(hex) Detail Explanation Kb 10, 20, 30, 40, 50 00 : RF(TV) 02: AV1

2. Designation
2.1 The adjustment is according to the order which is designated and which must be followed, according to the plan which can be changed only on agreeing. 2.2 Power Adjustment : Free Voltage 2.3 Magnetic Field Condition: Nil. 2.4 Input signal Unit : Product specification standard 2.5 Reserve after operation : Above 2 hours 2.6 Adjustment equipments : Pattern Generator (MSPG925F), DDC Adjustment Jig equipment, HDCP Adjustment Jig equipment.
2 3 4 5 6 7 8 9 Sub Brightness Sub Contrast Ah Ag 00 ~ 0X64 00 ~ 0X64 00 ~ 7f 00 ~ 7f 00 ~ 7f 00 ~ ff 00 ~ ff 00 ~ ff 00 00

03 : S-Video 04 : Component 1 06 : PC

R _ Offset Adjustment Aa G _ Offset Adjustment Ab B _ Off\set Adjustment Ac R _ Gain Adjustment Ad G _ Gain Adjustment Ae B _ Gain Adjustment Af Adjust Data Save Adjust OK ai ak

The data which is adjusted store The signal Adjustment was completed

3. Adjustments
3.1 Adjustment Details
The machine can be adjusted by itself automatically with factory automatic equipment, in case error occurs, set manual adjustment to standard.

10 11

3.3 PC signal Gain/Offset Adjustment (Execute first of all in adjustment process)
3.3.1 Adjustment Preparation - Execution of RF no signal during Heat Run over 30min - Pattern generator signal is connected to the DVI-I Jack of LCD TV. 3.3.2 Auto Gain/Offset Adjustment (Input signal Level : 730mV) - To use Pattern Generator(MSPG925FS), Apply Model 37, Patten 19 (XGA(1024 X 768)60Hz, white/black top and bottom pattern signal (Don't apply 16 gray signal) - Press IN-START Key by using the Remote Controller (SVC) , after converting to Adjustment-Mode, press VOL+ Key consecutively in Auto-Gain Menu. - After adjustment is complete, pressing enter key, stores and completes the process.

3.2 Adjustment signal Composition of The Auto Adjustment equipment
3.2.1 RS-232C Interchange 9600bps, Pin#2 : Rx, Pin#3 : Tx, 8bit, STOP bit=1, No Parity 3.2.2 Adjust data save * Save the adjusted data to the EEPROM with default value ai - 0 - 00 3.2.3 Adjust OK ak - 0 - 00 3.2.4 Screen Adjustment Instruction Forms CMD1 CMD2 SetID(0) Value a. CMD1,CMD2 : Instructions operated by Monitor b. SetID L 0h Set always 0 in Adjustment VALUE : Adjustment Value

- 10 -

3.4 Video signal Gain/Offset Adjustment (Auto adjustment)
- Execution of RF no signal during Heat Run over 30min - Connect to the LCD TV SCART input terminal with Patten Generator(MSPG-925FS) - Convert INPUT MODE to S-Video or AV1. - Connect RS-232C Communication Cable to the Auto Adjustment Equipment and SET's upgrade Port 3.4.1 Low Gray Adjustment - Apply Gray-Level(Model : 202 PAL_BDGH, pattern : 59) signal by using Pattern Generator(MSPG-925FS) - Check weather color-coordinates 23" & 26" & 32"AUO (x: 0.283, y:0.298, ±0.005), 32" LPL(x:0.280, y:0.290, ±0.005), 32"&27" CMO(x:0.275, y:0.285, ±0.005), 26" AUO (x:0.280, y: 0.285, ±0.005) is operated by using CA-110 equipment - If color-coordinates is not in Spec, adjust color-coordinates 23" & 26" & 32"AUO (x: 0.283, y:0.298, ±0.005), 32"LPL (x:0.280, y:0.290, ±0.005), 32"&27" CMO(x:0.275, y:0.285, ±0.005), 26" AUO (x:0.280, y:0.285, ±0.005) by adjusting Red Offset, Blue Offset 3.4.2 White Balance Adjustment - Apply 95% White (Model : 202 PAL_BDGH, pattern : 47, luminance spec : 250cd/m^2 over) signal by using Patten Generator(MSPG925FS) - Check whether color-coordinates(x:0.283, y:0.298, ±0.005) is operated by using CA-110 equipment - If color-coordinates is not in Spec, adjust colorcoordinates(x:0.283, y:0.298, ±0.005) by adjusting Red Gain, Blue Gain - All adjustment takes color-coordinates with based on G, changing R and B. If it is not adjusted, adjust with fixed B, changing G and R.

3.5.2 White Balance Adjustment - Apply 95% White(Model:210 576i, pattern : 47, luminance spec : 250cd/m^2 over) signal by using Patten Generator (MSPG925FS) - Check whether color-coordinates(x:0.283, y:0.298, ±0.005) is operated by using CA-110 equipment - If color-coordinates is not in Spec, adjust colorcoordinates(x: 0.283, y:0.298, ±0.005) by adjusting Red Gain, Blue Gain - All adjustment takes color-coordinates with based on G, changing R and B. If it is not adjusted, adjust with fixed B, changing G and R.

4. EDID (The Extended Display Identification Data) SETTING
- Connect D-Sub to DVI-I Cable to DVI-I Jack. - Input analog signal and check pc video in the screen. - After appearing the pc video, write Analog EDID data. - Connect DVI D Cable to DVI Jack. - Input digital signal and check pc video in the screen. - After appearing the pc video, write digital EDID data. [DDC DATA Analog Set]
00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F 00 00 FF FF FF FF FF FF 00 1E 6D 45 75 01 01 01 01 10 0C 0E 01 03 01 40 26 78 08 B1 DA A1 56 48 98 24 20 13 48 4B A1 08 00 31 40 01 01 01 01 45 40 01 01 30 61 40 81 80 01 01 4E 1F 00 90 51 00 1B 30 40 88 40 13 00 A2 0B 32 00 00 18 1B 21 50 A0 51 00 1E 30 50 48 88 35 00 A2 0B 32 00 00 1C 00 00 00 FD 00 3B 60 3D 1F 30 09 00 0A 20 20 20 20 20 20 00 00 00 FC 70 00 52 5A 32 37 4C 5A 35 35 0A 20 20 20 20 00 D7

3.5 Component signal Gain/Offset Adjustment (Auto adjustment)
- Execution of RF no signal during Heat Run over 30min - Connect to the LCD TV Component1 terminal with Patten Generator(MSPG-925FS) - Convert INPUT MODE to Component1. - Connect RS-232C Communication Cable to the Auto Adjustment Equipment and SET's upgrade Port 3.5.1 Low Gray Adjustment - Apply Gray-Level(Model : 210 576i, pattern : 59) signal by using Patten Generator(MSPG925FS) - Check whether color-coordinates 23" & 26" & 32"AUO (x: 0.283, y:0.298, ±0.005), 32"LPL(x:0.280, y:0.290, ±0.005), 32"&27" CMO(x:0.275, y:0.285, ±0.005), 26" AUO (x:0.280, y:0.285, ±0.005) is operated by using CA-110 equipment - If color-coordinates is not in Spec, adjust color-coordinates 23" & 26" & 32"AUO (x:0.283, y:0.298, ±0.005), 32"LPL (x:0.280, y:0.290, ±0.005), 32"&27" CMO(x:0.270, y:0.285, ±0.005) , 26" AUO (x:0.280, y:0.285, ±0.005) by adjusting Red Offset, Blue Offset

[DDC DATA Digital Set]
00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F 00 00 FF FF FF FF FF FF 00 1E 6D 46 75 01 01 01 01 10 00 0E 01 03 81 40 26 78 08 B1 DA A1 56 48 98 24 20 13 48 4B A1 08 00 31 40 01 01 01 01 45 40 01 01 30 61 40 81 80 01 01 4E 1F 00 90 51 00 1B 30 40 88 40 13 00 A2 0B 32 00 00 18 1B 21 50 A0 51 00 1E 30 50 48 88 35 00 A2 0B 32 00 00 1C 00 00 00 FD 00 3B 60 3D 1F 30 09 00 0A 20 20 20 20 20 20 00 00 00 FC 70 00 52 5A 32 37 4C 5A 35 35 0A 20 20 20 20 01 55 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F 00 02 03 0E 00 49 85 04 02 01 03 11 12 13 14 01 1D 10 00 72 51 D0 1E 20 6E 28 55 00 C4 8E 21 00 00 1A 20 8C 0A D0 8A 20 E0 2D 10 10 3E 96 00 C4 8E 21 00 30 00 18 01 1D 80 18 71 1C 16 20 58 2C 25 00 C4 8E 40 21 00 00 9E 00 00 00 00 00 00 00 00 00 00 00 00 50 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 95

- 11 -

5. Shipping Conditions
No 1 2 3 4 5 6 7 Power Volume Level Main Picture Input Main Last Channel Mute ARC Station Auto Program Manual Program Program Edit Favorite Program 8 Picture PSM Dynamic Contrast Brightness Colour Sharpness Tint 9 Sound SSM AVL Balance 10 Special Input Child Lock Auto sleep Language 11 PC H-Position V-Position Variable by each mode Clock Phase Auto Configure None Dynamic 80 40 70 70 0 Flat Off 0 TV Off Off English(Area Management) NTSC OPTION Item Off 30 TV Pr 01 Off 16 : 9 Condition Remark

- 12 -

OPTION DATA SETTING(PAL)
No Item Condition Remark Option3 1 1 0 : SideAV Off 1 : SideAV On 2 SCART 1 0 : SCART Off 1 : SCART On 3 PC 1 0 : PC Off 1 : PC On 4 SideComp 1 0 :SideComp Off 1 :SideComp ON 5 16:9 1 0 : Wide OFF 1 : Wide On 6 200PR 0 0 : 100 Program 1 : 200 Program 7 Text 1 0 : Text Off 1 : Text On 8 ACMS 1 0 : ACMS On 1 : ACMS Off Option2 1 HiDev 0 0 : HiDev Off 1 : HiDev On 2 Hotel 0 0 : Hotel Off 1 : Hotel On 3 Top 1 0 : Top OFF 1 : Top ON 4 I II SAVE 1 0 : Ch. Sound Non Memory 1 : Ch. Sound Memory 5 Turbo Vol 0 0 : except below area(Off) 1 : Middle-East Area Vol On 6 Ch/Aus 0 0 : except below area(Off) 1 : China, Australia On 3 4 Inch opt DDCi 0 Analog 2 Txt Lang 0 Language 1 0 : Eng Only 1 : EU5 2 : 12 nations (Europe) 3 : Eng + Chinese 4 : Eng + Arab + Urdu 5 : Eng + FARSI 0 : WEST EU 1 : EAST EU1 2 : TURKY EU 3 : EAST EU2 4 : CYRILLIC1 5 : CYRILLIC2 6 : CYRILLIC3 7 : TURK GRE1 8 : TURK GRE2 9 : TURK GRE3 10 :ARAB FRAN 11 :ARAB ENG 12 :ARAB HEB1 13 :ARAB HEB2 14 :FARSI ENG 15 :FARSI FRA 16 :FARI ALL reserved Analog : Analog Digital : Digital

Option1 1 SideAV

- 13 -

SVC REMOCON
NO
1 2 3 4 5 6 7 8 9 10 11

KEY
POWER

FUNTION

REAMARK

12

13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38

To turn the TV on or off To turn the TV on automatically if the power is supplied to the TV. (Use the POWER ON POWER key to deactivate): It should be deactivated when delivered. To activate the mute function. MUTE To check TV screen image easily. P-CHECK To check TV screen sound easily S-CHECK To select size of the main screen (Normal, Spectacle, Wide or Zoom) ARC Switch to closed caption broadcasting CAPTION To toggle on/off the teletext mode TXT To select an external input for the TV screen TV/AV To start turbo sound TURBO SOUND TURBO PICTURE To start turbo picture To enter adjustment mode when manufacturing the TV sets. To adjust the screen voltage (automatic): In-start mute Adjust AV(Enter into W/B adjustment mode) IN-START W/B adjustment (automatic): After adjusting the screen W/B adjustment Exit two times (Adjustment completed) To enter into the adjustment mode. To adjust horizontal line and sub-brightness. ADJ To select the multiple sound mode (Mono, Stereo or Foreign language) MPX To release the adjustment mode EXIT To easily adjust the screen according to surrounding brightness APC(PSM) To easily adjust sound according to the program type ASC(SSM) To check component input MULTIMIDIA To check the front AV FRONT-AV To move channel up/down or to select a function displayed on the screen. CH To adjust the volume or accurately control a specific function. VOL To set a specific function or complete setting. ENTER To move the channel down in the PIP screen. PIP CH-(OP1) To use as a red key in the teletext mode To move the channel in the PIP screen PIP CH+(OP2) To use as a green key in the teletext mode To switch between the main and sub screens PIP SWAP(OP3) To use as a yellow key in the teletext mode To select the input status in the PIP screen PIP INPUT(OP4) To use as a blue key in the teletext mode To set a function that will automatically adjust screen status to match EYE the surrounding brightness so natural color can be displayed. To select the functions such as video, voice, function or channel. MENU To set the delivery condition status after manufacturing the TV set. IN-STOP To halt the main screen in the normal mode, or the sub screen at the PIP screen. STILL Used as a hold key in the teletext mode (Page updating is stopped.) Displays the teletext time in the normal mode TIME Enables to select the sub code in the teletext mode Used as the size key in the PIP screen in the normal mode SIZE Used as the size key in the teletext mode Used as the index key in the teletext mode (Top index will be MULTI PIP displayed if it is the top text.) To select the position of the PIP screen in the normal mode Used as the update key in the teletext mode (Text will be POSITION displayed if the current page is updated.) Used as Mode in the teletext mode MODE To select the simultaneous screen PIP To adjust screen tilt TILT To manually select the channel. 0~9

Shortcut keys Shortcut keys Shortcut keys

Use the AV key to enter the screen W/B adjustment mode.

Shortcut keys Shortcut keys

Shortcut keys

- 14 -

TROUBLESHOOTING

No power (LED indicator off)

:[A]Process

Check 24V or 12V of Power B/D

Fail

Check short of main B/D or Change Power B/D

Pass Check Output of L3, L1300 Change L3, L1300 Fail

Pass

Check Output of IC1300, IC4 or IC8

Change IC1300,IC4 or IC8 Fail Fail

Change L808,L809 (F801,F802)

Pass

Check LED Assy Fail

Change LED Assy

Pass

Check P101 Connector

- 15 -

No Raster

:[B]Process

Check LED Status on display unit

Repeat A PROCESS Fail

Pass

Check L900,L901 L902,L903

Fail

Change L900,L901, L902,L903

Pass

Check the input/ Output of IC901

Change IC901 Fail

Pass

Check inverter Connector or inverter

Fail

Change inverter connector or inverter

Pass

Check panel link Cable or module

Faill

Change panel link cable or module

Pass

Check input source cable and jack

Fail

Change module

- 16 -

No Raster on Component signal

Repeat [A] Process

Pass

Check the signal of Q310,Q315,Q316

Fail

Change Q310,Q315,Q316

Pass

Check the input/ output of IC1

Fail

Re-soldering or Change the defect part

Check the input/output of IC500, IC600

Fail

Re-soldering or Change the defect part

Pass

Check the input/ output of IC901

Faill

Re-soldering or Change the defect part

Pass

Check input source cable and jack

- 17 -

No Raster on AV Signa (Video1,Video2, S-Video)

No Raster on TV(RF) signal

Repeat [A] Process

Fail

Check the output of TU1000

Fail

Check 5V, 33V of TU1000 Re-soldering or Change the defect part

Pass

Check the signal of C316,C317,Q308,Q313

Fail

Change C316,C317, Q308,Q313

Pass

Check the input/output of IC1

Faill

Re-soldering or Change the defect part

Pass

Check the input/output of IC500, IC600

Fail

Re-soldering or Change the defect part

Pass

Check the input/output of IC901

Fail

Re-soldering or Change the defect part

Pass

Check input source cable and jack

- 18 -

No Sound

Check the input source

Fail

Change source input

Pass

Check the input/output of IC1 Pass

Fail

Re-soldering or Change the defect part

Check the input/output of IC100,IC101

Fail

Re-soldering or Change the defect part

Pass

Check the speaker Fail Pass

Change speaker

Check the speaker wire

- 19 -

BLOCK DIAGRAM

- 20 -

BLOCK DIAGRAM DESCRIPTION
1. Video control and display data Video signal is received from TUNER, AV port(AV1,AV2,S-Video,Component) and goes to the one-chip video decoder (VCTI) which separate the R,G,B signal and passes on the signal to AD converter(AD9883) which converts 4:4:4 video format into digital and gives output to the Picture Enhancer(FLI2300).This picture enhancer improves the quality of the picture by changing the level of RGB signals.The output of this enhancer chip is fed to the deinterlacer ,which in turn goes to the Scalar (GM5221).The scalar gives the output on the LVDS cable which is connected to LCD module. VCTi acts a micom and is responsible for video processing and audio signal processing.It accepts the RF signal and separates sound and picture from it. Scaler is reponsible for regulating the timing of signal to LCD panel and size and location of the signal.Graphic control accepts the PC(Analog RGB) and DVI-D (Digital ) signal, Scalar is reponsible for regulating the timing of signal to LCD panel and size and location of the signal.Graphic control accepts the PC(Analog RGB) and DVI-D (Digital ) signal,the signal of PC input is connected to analog port in Scaler and the signal of DVI-D input is connected to digital port. Thus it receives two input and switch between them to give output at the LVDS which in turn gives output at the LCD module. 2. Power unit The power board supplies a DC voltage of 33V, 24V, 12V to the main board.out of this 33v is used by the tuner and 24v is used directly by the inverter and the sound amplifier IC. 24v also is converted into 5v by a regulator. The 5v is changed into 3.3v and 1.8v by a regulator, both voltages(3.3v, 1.8v ) is used by VCTI, Scaler, FLI2300 and AD9883. The voltage of LCD Panel is 12v.

- 21 -

WIRING DIAGRAM

9 8

Wiring Part List
No. 1 2 Part No. 6631T11020N 6631T20033F 3 4 5 6 6631T20032E 6631T25019K 6631T20033B 6631T20033C 7
SPK

4 3

11 2

6631T20033D 8 9
10

- 22 1 POWER BOARD MAIN BORAD 6 5

SPK

6631T20029Z 6631T20029Y 10 11 6631T20033E 6631T20032F

7

EXPLODED VIEW

161

080 050 120 140

162 090

010 020 150 030 130 110 100

- 23 070

060

040

EXPLODED VIEW PARTS LIST
No. 010 020 030 PART NO. 3091TKE018F 6304FCI014A 3809TKE035J 3809TKE035H 040 3043TKK171B 3043TKK171F 050 060 070 080 090 100 110 120 130 6871TVT370C 6871TST762C 6871TST589D 4951TKS156F 6871TPT275E 6871TST588D 4814TKK280A 33139P2020A 3551TKK516L 3551TKK516B 140 4951TKK169S 4951TKK169J 150 161 162 161+162 3550TKK516A 6401900142A 6401900143A 6401900129A DESCRIPTION Cover Assembly, RZ-27LZ50 BRAND 3091TKE012A 407AF LGEWA C/SKD LCD,Panel-TFT, V270B1-L01 27INCH 1366X768 550CD COLOR 75% V270B1-L01 550NITS 8MS Cover Assembly, RZ-26LZ55 ONLY 3808TKE005 40AF LGEMA-EXPORT MOLD PHANTOM Cover Assembly, RZ-26LZ55 3808TKE005 C/SKD Base Assembly, RZ-26LZ50 LGEWA C/SKD Base Assembly, RZ-26LZ50 . NONE LGENT PHANTOM PCB Assembly,Video, RM-32/26/23LZ50 SIDE A/V SUB TOTAL BRAND LF PCB Assembly,Sub, 26/27LZ50 LED & P/SW TOTAL BRAND -LFPCB Assembly,Sub, RZ-26LZ50 CONTROL TOTAL BRAND -LFPlate Assembly, FRAME, CMO RZ-27LZ50 C/SKD PCB Assembly,Power, RM-32LZ50 POWER TOTAL BRAND 26-32INCH PB FREE PCB Assembly,Sub, RZ-26LZ50 IR SUB TOTAL BRAND -LFPlate, PRESS SPTE T0.3 REAR POWER Main Total Assembly, CMO ML-041A LF RZ-27LZ55 BRAND Cover Assembly, RZ-32LZ50 LGEMA PHANTOM REAR A/V ASSY PHONE Cover Assembly, RZ-30LZ50 REAR NON AV C/SKD Plate Assembly, REAR SHIELD 26LZ50, LGEMA PHAMTOM Plate Assembly, REAR RZ-26LZ50 C/SKD Cover, MOLD ABS RZ-26LZ50 REAR Speaker Assembly, RZ-23/26LZ55 LGEMA SPK L 5P -LFSpeaker Assembly, RZ-23/26LZ55 LGEMA SPK R 4P -LFSpeaker Assembly, RZ-20LA70 4OHM 7W MAX12W

- 24 -

REPLACEMENT PARTS LIST
For Capacitor & Resistors, the charactors at 2nd and 3rd digit in the P/No. means as follows; CC, CX, CK, CN, CH : Ceramic CQ : Polyestor CE : Electrolytic CF : Fixed Film RD : Carbon Film RS : Metal Oxide Film RN : Metal Film RH : CHIP, Metal Glazed(Chip) RR : Drawing

*S *AL LOC. NO.

PART NO.

DATE: 2006. 03.03. DESCRIPTION / SPECIFICATION

*S *AL LOC. NO. C805 C806 C807 C814 C815 C857 C858 C859 C860 C861 C862 C863 C87 C88 C89 C900 C91 C953 C957 C959 C962 C965 C97 C972 C974 C1006 C108 C1100 C1102 C111 C1112 C1113 C1114 C1115 C112 C119 C120 C1202 C123 C124 C1299 C1304 C131 C132 C133 C134 C404 C971 C1001 C1002 C1003 C1004 C1007 C1010

PART NO. 0CE227WF6DC 0CE227WF6DC 0CE227WF6DC 0CE227WF6DC 0CH8476F691 0CE107WF6DC 0CH8476F691 0CH8476F691 0CH8476F691 0CH8476F691 0CH8476F691 0CH8476F691 0CE107WF6DC 0CH8476H691 0CE107WF6DC 0CE107WF6DC 0CE107WF6DC 0CH8476F691 0CE107WF6DC 0CE107WF6DC 0CE107WF6DC 0CE107WF6DC 0CE107WF6DC 0CH8476H691 0CE107WF6DC 0CE106EK638 0CE476EK638 0CE106BF618 0CE107EK638 0CE475EK638 0CE108EF618 0CE108EF618 0CE108EF618 0CE108EF618 0CE475EK638 0CE106BF618 0CE106BF618 0CE477EJ618 0CE477EJ618 0CE477EJ618 0CE477EJ618 0CE477EJ618 0CE477EJ618 0CE477EJ618 0CE477EJ618 0CE477EJ618 0CE227EJ638 0CE107BF618 0CH3103K516 0CH3103K516 0CH3103K516 0CH3103K516 0CH3103K516 0CK273DK51A

DATE: 2006. 03.03. DESCRIPTION / SPECIFICATION MVK8.0TP16VC220M 220u 20% 1 MVK8.0TP16VC220M 220u 20% 1 MVK8.0TP16VC220M 220u 20% 1 MVK8.0TP16VC220M 220u 20% 1 MVK6.3TP16VC47M 47u 20% 16V MVK6.3TP16VC100M 100u 20% 1 MVK6.3TP16VC47M 47u 20% 16V MVK6.3TP16VC47M 47u 20% 16V MVK6.3TP16VC47M 47u 20% 16V MVK6.3TP16VC47M 47u 20% 16V MVK6.3TP16VC47M 47u 20% 16V MVK6.3TP16VC47M 47u 20% 16V MVK6.3TP16VC100M 100u 20% 1 MVK8.0TP25VC47M 47u 20% 25V MVK6.3TP16VC100M 100u 20% 1 MVK6.3TP16VC100M 100u 20% 1 MVK6.3TP16VC100M 100u 20% 1 MVK6.3TP16VC47M 47u 20% 16V MVK6.3TP16VC100M 100u 20% 1 MVK6.3TP16VC100M 100u 20% 1 MVK6.3TP16VC100M 100u 20% 1 MVK6.3TP16VC100M 100u 20% 1 MVK6.3TP16VC100M 100u 20% 1 MVK8.0TP25VC47M 47u 20% 25V MVK6.3TP16VC100M 100u 20% 1 KMG5.0TP50VB10M 10u 20% 50V KMG5.0TP50VB47M 47u 20% 50V ESM106M016T1G5C11G 10u 20% KMG5.0TP50VB100M 100u 20% 5 KMG5.0TP50VB4.7M 4.7u 20% 5 KMG5.0TP16VB1000M 1000u 20% KMG5.0TP16VB1000M 1000u 20% KMG5.0TP16VB1000M 1000u 20% KMG5.0TP16VB1000M 1000u 20% KMG5.0TP50VB4.7M 4.7u 20% 5 ESM106M016T1G5C11G 10u 20% ESM106M016T1G5C11G 10u 20% KMG5.0TP35VB470M 470u 20% 3 KMG5.0TP35VB470M 470u 20% 3 KMG5.0TP35VB470M 470u 20% 3 KMG5.0TP35VB470M 470u 20% 3 KMG5.0TP35VB470M 470u 20% 3 KMG5.0TP35VB470M 470u 20% 3 KMG5.0TP35VB470M 470u 20% 3 KMG5.0TP35VB470M 470u 20% 3 KMG5.0TP35VB470M 470u 20% 3 KMG5.0TP35VB220M 220u 20% 3 ESM107M016T1G5E11G 100u 20% C2012Y5P1H103KT 10000p 10% C2012Y5P1H103KT 10000p 10% C2012Y5P1H103KT 10000p 10% C2012Y5P1H103KT 10000p 10% C2012Y5P1H103KT 10000p 10% C1608Y5P273KGT 27000p 10% 5

CAPACITOR
C100 C1008 C1503 C1504 C17 C206 C208 C219 C221 C225 C226 C227 C228 C235 C236 C300 C301 C302 C303 C304 C307 C308 C309 C312 C313 C314 C315 C316 C317 C4001 C4002 C4008 C4012 C4013 C4015 C4022 C4023 C4024 C5 C502 C503 C52 C520 C525 C54 C543 C55 C560 C566 C604 C605 C607 C62 C63 C703 0CH8476F691 0CE227WF6DC 0CE107WF6DC 0CE107WF6DC 0CH8106J691 0CH8226F691 0CH8226F691 0CH8226F691 0CH8226F691 0CH8106J691 0CH8106J691 0CH8106J691 0CH8106J691 0CE107WF6DC 0CE107WF6DC 0CE107WF6DC 0CE107WF6DC 0CH8106F691 0CH8106F691 0CH8106F691 0CH8106F691 0CE107WF6DC 0CH8106F691 0CH8106F691 0CE107WF6DC 0CH8106F691 0CH8106F691 0CH8106F691 0CH8106F691 0CH8106J691 0CH8106J691 0CH8106J691 0CH8106J691 0CH8106J691 0CH8106J691 0CH8106J691 0CH8106J691 0CE107WF6DC 0CE475WJ6DC 0CH8476F691 0CH8476F691 0CE107WF6DC 0CH8106F691 0CH8106F691 0CE107WF6DC 0CH8476F691 0CE107WF6DC 0CH8476F691 0CE107WF6DC 0CH8476F691 0CH8476F691 0CH8476F691 0CE107WF6DC 0CE107WF6DC 0CE107WF6DC MVK6.3TP16VC47M 47u 20% 16V MVK8.0TP16VC220M 220u 20% 1 MVK6.3TP16VC100M 100u 20% 1 MVK6.3TP16VC100M 100u 20% 1 MVK5.0TP35VC10M 10u 20% 35V MVK5.0TP16VC22M 22u 20% 16V MVK5.0TP16VC22M 22u 20% 16V MVK5.0TP16VC22M 22u 20% 16V MVK5.0TP16VC22M 22u 20% 16V MVK5.0TP35VC10M 10u 20% 35V MVK5.0TP35VC10M 10u 20% 35V MVK5.0TP35VC10M 10u 20% 35V MVK5.0TP35VC10M 10u 20% 35V MVK6.3TP16VC100M 100u 20% 1 MVK6.3TP16VC100M 100u 20% 1 MVK6.3TP16VC100M 100u 20% 1 MVK6.3TP16VC100M 100u 20% 1 MVK4.0TP16VC10M 10u 20% 16V MVK4.0TP16VC10M 10u 20% 16V MVK4.0TP16VC10M 10u 20% 16V MVK4.0TP16VC10M 10u 20% 16V MVK6.3TP16VC100M 100u 20% 1 MVK4.0TP16VC10M 10u 20% 16V MVK4.0TP16VC10M 10u 20% 16V MVK6.3TP16VC100M 100u 20% 1 MVK4.0TP16VC10M 10u 20% 16V MVK4.0TP16VC10M 10u 20% 16V MVK4.0TP16VC10M 10u 20% 16V MVK4.0TP16VC10M 10u 20% 16V MVK5.0TP35VC10M 10u 20% 35V MVK5.0TP35VC10M 10u 20% 35V MVK5.0TP35VC10M 10u 20% 35V MVK5.0TP35VC10M 10u 20% 35V MVK5.0TP35VC10M 10u 20% 35V MVK5.0TP35VC10M 10u 20% 35V MVK5.0TP35VC10M 10u 20% 35V MVK5.0TP35VC10M 10u 20% 35V MVK6.3TP16VC100M 100u 20% 1 MVK4.0TP35VC4.7M 4.7u 20% 3 MVK6.3TP16VC47M 47u 20% 16V MVK6.3TP16VC47M 47u 20% 16V MVK6.3TP16VC100M 100u 20% 1 MVK4.0TP16VC10M 10u 20% 16V MVK4.0TP16VC10M 10u 20% 16V MVK6.3TP16VC100M 100u 20% 1 MVK6.3TP16VC47M 47u 20% 16V MVK6.3TP16VC100M 100u 20% 1 MVK6.3TP16VC47M 47u 20% 16V MVK6.3TP16VC100M 100u 20% 1 MVK6.3TP16VC47M 47u 20% 16V MVK6.3TP16VC47M 47u 20% 16V MVK6.3TP16VC47M 47u 20% 16V MVK6.3TP16VC100M 100u 20% 1 MVK6.3TP16VC100M 100u 20% 1 MVK6.3TP16VC100M 100u 20% 1

- 25 -

*S *AL LOC. NO. C107 C109 C11 C110 C113 C114 C12 C127 C128 C13 C1300 C1302 C1303 C1305 C1307 C1308 C135 C136 C14 C15 C16 C18 C19 C2 C20 C200 C23 C237 C238 C3 C306 C318 C319 C324 C328 C329 C331 C336 C340 C341 C352 C354 C355 C4 C4004 C4005 C4006 C4009 C4010 C4011 C4016 C4017 C4019 C4021 C42 C43 C44 C45 C46 C49 C50 C500

PART NO. 0CK225DFK4A 0CH3103K516 0CH3104K566 0CH3103K516 0CK225DFK4A 0CK225DFK4A 0CH3104K566 0CH3104K566 0CH3104K566 0CH6102K406 0CK105DK94A 0CH3103K516 0CH6101K416 0CK105DK94A 0CH3103K516 0CH6101K416 0CH3104K566 0CH3104K566 0CH6102K406 0CH3104K566 0CH3104K566 0CK106EF56A 0CH3104K566 0CH6102K406 0CH6102K406 0CH6221K416 0CH3104K566 0CH6102K406 0CH6102K406 0CH3104K566 0CH3104K566 0CH3104K566 0CH6120K416 0CH6120K416 0CH6120K416 0CH6120K416 0CH6150K416 0CH6150K416 0CH6150K416 0CH6150K416 0CC270DK41A 0CH6471K416 0CH6471K416 0CH3104K566 0CH3104K566 0CH3222K516 0CH3222K516 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH6102K406 0CH3104K566 0CH3104K566 0CH6102K406 0CH3104K566 0CH6102K406 0CH3104K566

DATE: 2006. 03.03. DESCRIPTION / SPECIFICATION C2012Y5V1C225MT 2200000p 20 C2012Y5P1H103KT 10000p 10% 0805B104K500CT 100000p 10% C2012Y5P1H103KT 10000p 10% C2012Y5V1C225MT 2200000p 20 C2012Y5V1C225MT 2200000p 20 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% C2012S2L1H102JT 1000p 5% 50 0805F105Z500CT 1000000p -20 C2012Y5P1H103KT 10000p 10% C2012C0G1H101JT 100p 5% 50V 0805F105Z500CT 1000000p -20 C2012Y5P1H103KT 10000p 10% C2012C0G1H101JT 100p 5% 50V 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% C2012S2L1H102JT 1000p 5% 50 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% C3216X7R1C106KT 10000000p 1 0805B104K500CT 100000p 10% C2012S2L1H102JT 1000p 5% 50 C2012S2L1H102JT 1000p 5% 50 C2012C0G1H221JT 220p 5% 50V 0805B104K500CT 100000p 10% C2012S2L1H102JT 1000p 5% 50 C2012S2L1H102JT 1000p 5% 50 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% C2012C0G1H120JT 12p 5% 50V C2012C0G1H120JT 12p 5% 50V C2012C0G1H120JT 12p 5% 50V C2012C0G1H120JT 12p 5% 50V C2012C0G1H150JT 15p 5% 50V C2012C0G1H150JT 15p 5% 50V C2012C0G1H150JT 15p 5% 50V C2012C0G1H150JT 15p 5% 50V C2012C0G1H270JT 27p 5% 50V C2012C0G1H471JT 470p 5% 50V C2012C0G1H471JT 470p 5% 50V 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% C2012Y5P1H222KT 2200p 10% 5 C2012Y5P1H222KT 2200p 10% 5 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% C2012S2L1H102JT 1000p 5% 50 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% C2012S2L1H102JT 1000p 5% 50 0805B104K500CT 100000p 10% C2012S2L1H102JT 1000p 5% 50 0805B104K500CT 100000p 10%

*S *AL LOC. NO. C505 C506 C507 C508 C509 C51 C510 C511 C512 C513 C514 C517 C518 C519 C521 C522 C523 C526 C527 C528 C529 C53 C530 C531 C532 C533 C534 C535 C536 C537 C538 C539 C540 C541 C542 C544 C545 C546 C547 C549 C550 C551 C552 C553 C554 C555 C556 C557 C558 C559 C567 C59 C6 C60 C606 C608 C609 C61 C614 C615 C616 C618

PART NO. 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH6102K406 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CK105DK94A 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CK105DK94A 0CH6102K406 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566

DATE: 2006. 03.03. DESCRIPTION / SPECIFICATION 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% C2012S2L1H102JT 1000p 5% 50 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805F105Z500CT 1000000p -20 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805F105Z500CT 1000000p -20 C2012S2L1H102JT 1000p 5% 50 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10%

- 26 -

*S *AL LOC. NO. C619 C620 C621 C622 C623 C624 C625 C627 C628 C629 C632 C633 C634 C635 C636 C637 C638 C639 C64 C640 C65 C66 C67 C700 C701 C702 C704 C705 C74 C75 C751 C755 C756 C757 C758 C76 C760 C761 C77 C79 C80 C804 C808 C809 C81 C810 C811 C812 C813 C82 C83 C84 C850 C851 C852 C853 C854 C855 C856 C86 C864 C865

PART NO. 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH2822K516 0CH3823K516 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CK106EF56A 0CH3104K566 0CH3104K566 0CH6120K416 0CH6120K416 0CH3104K566 0CH3104K566 0CH6102K406 0CH3104K566 0CH3104K566 0CH6471K416 0CH6471K416 0CH6471K416 0CH6101K416 0CK106EF56A 0CH3104K566 0CH3104K566 0CK106EF56A 0CK106EF56A 0CK106EF56A 0CH3104K566 0CK105DK94A 0CK105DK94A 0CK106EF56A 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH6102K406 0CK106EF56A 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH6102K406 0CH3104K566 0CH3104K566

DATE: 2006. 03.03. DESCRIPTION / SPECIFICATION 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B822K500CT 8200p 10% 50 C2012Y5P1H823KT 82000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% C3216X7R1C106KT 10000000p 1 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% C2012C0G1H120JT 12p 5% 50V C2012C0G1H120JT 12p 5% 50V 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% C2012S2L1H102JT 1000p 5% 50 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% C2012C0G1H471JT 470p 5% 50V C2012C0G1H471JT 470p 5% 50V C2012C0G1H471JT 470p 5% 50V C2012C0G1H101JT 100p 5% 50V C3216X7R1C106KT 10000000p 1 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% C3216X7R1C106KT 10000000p 1 C3216X7R1C106KT 10000000p 1 C3216X7R1C106KT 10000000p 1 0805B104K500CT 100000p 10% 0805F105Z500CT 1000000p -20 0805F105Z500CT 1000000p -20 C3216X7R1C106KT 10000000p 1 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% C2012S2L1H102JT 1000p 5% 50 C3216X7R1C106KT 10000000p 1 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% C2012S2L1H102JT 1000p 5% 50 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10%

*S *AL LOC. NO. C866 C867 C868 C869 C870 C90 C908 C909 C910 C911 C912 C913 C914 C915 C916 C917 C918 C919 C92 C920 C921 C922 C923 C924 C925 C926 C927 C928 C929 C930 C931 C935 C936 C937 C938 C939 C940 C941 C942 C943 C944 C945 C946 C947 C948 C949 C950 C951 C952 C958 C96 C963 C966 C967 C968 C969 C970 C973 C10 C1015 C1016 C115

PART NO. 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH6080K116 0CH6080K116 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CK225DFK4A 0CH3104K566 0CH3104K566 0CH3103K516 0CH3103K516 0CH6101K416 0CH3104K566 0CH3104K566 0CH3104K566 0CK104CK56A 0CC680CK41A 0CC680CK41A 0CK104CK56A

DATE: 2006. 03.03. DESCRIPTION / SPECIFICATION 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% C2012C0G1H080DT 8p 0.5PF 50 C2012C0G1H080DT 8p 0.5PF 50 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% C2012Y5V1C225MT 2200000p 20 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% C2012Y5P1H103KT 10000p 10% C2012Y5P1H103KT 10000p 10% C2012C0G1H101JT 100p 5% 50V 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0805B104K500CT 100000p 10% 0603B104K500CT 100000p 10% C1608C0G1H680JT 68p 5% 50V C1608C0G1H680JT 68p 5% 50V 0603B104K500CT 100000p 10%

- 27 -

*S *AL LOC. NO. C116 C117 C118 C121 C122 C125 C126 C1301 C1306 C1500 C1501 C1502 C202 C203 C204 C205 C207 C209 C21 C210 C211 C214 C217 C218 C22 C220 C222 C223 C224 C24 C25 C26 C27 C28 C29 C30 C32 C33 C34 C343 C348 C35 C353 C37 C40 C4000 C4003 C4007 C4014 C4018 C4020 C41 C47 C48 C5001 C501 C504 C515 C516 C524 C600 C601

PART NO. 0CK562CK51A 0CK562CK51A 0CK104CK56A 0CC100CK41A 0CC100CK41A 0CK105EK56A 0CK105EK56A 0CK103CK51A 0CK103CK51A 0CC330CK41A 0CC330CK41A 0CC330CK41A 0CC101CK41A 0CC221CK41A 0CC471CK41A 0CC471CK41A 0CC102CK41A 0CC101CK41A 0CC102CK41A 0CC101CK41A 0CC102CK41A 0CC101CK41A 0CC471CK41A 0CC471CK41A 0CC102CK41A 0CC102CK41A 0CC102CK41A 0CC101CK41A 0CC101CK41A 0CC102CK41A 0CK104CK56A 0CK104CK56A 0CK104CK56A 0CK334CF94A 0CK104CK56A 0CK334CF94A 0CK334CF94A 0CK334CF94A 0CK104CK56A 0CC270CK41A 0CC270CK41A 0CK334CF94A 0CC270CK41A 0CK334CF94A 0CK104CK56A 0CK104CK56A 0CC150CK41A 0CC150CK41A 0CK104CK56A 0CK104CK56A 0CK104CK56A 0CK104CK56A 0CC220CK41A 0CC220CK41A 0CK104CK56A 0CC101CK41A 0CK104CK56A 0CC330CK41A 0CC330CK41A 0CK104CK56A 0CC220CK41A 0CC220CK41A

DATE: 2006. 03.03. DESCRIPTION / SPECIFICATION C1608Y5P1H562KT 5600p 10% 5 C1608Y5P1H562KT 5600p 10% 5 0603B104K500CT 100000p 10% C1608C0G1H100JT 10p 5% 50V C1608C0G1H100JT 10p 5% 50V C3216X7R1H105KT 1000000p 10 C3216X7R1H105KT 1000000p 10 0603B103K500CT 10000p 10% 5 0603B103K500CT 10000p 10% 5 C1608C0G1H330JT 33p 5% 50V C1608C0G1H330JT 33p 5% 50V C1608C0G1H330JT 33p 5% 50V C1608C0G1H101JT 100p 5% 50V C1608C0G1H221JT 220p 5% 50V C1608C0G1H471JT 470p 5% 50V C1608C0G1H471JT 470p 5% 50V C1608C0G1H102JT 1000p 5% 50 C1608C0G1H101JT 100p 5% 50V C1608C0G1H102JT 1000p 5% 50 C1608C0G1H101JT 100p 5% 50V C1608C0G1H102JT 1000p 5% 50 C1608C0G1H101JT 100p 5% 50V C1608C0G1H471JT 470p 5% 50V C1608C0G1H471JT 470p 5% 50V C1608C0G1H102JT 1000p 5% 50 C1608C0G1H102JT 1000p 5% 50 C1608C0G1H102JT 1000p 5% 50 C1608C0G1H101JT 100p 5% 50V C1608C0G1H101JT 100p 5% 50V C1608C0G1H102JT 1000p 5% 50 0603B104K500CT 100000p 10% 0603B104K500CT 100000p 10% 0603B104K500CT 100000p 10% C1608Y5V1C334ZT 330000p -20 0603B104K500CT 100000p 10% C1608Y5V1C334ZT 330000p -20 C1608Y5V1C334ZT 330000p -20 C1608Y5V1C334ZT 330000p -20 0603B104K500CT 100000p 10% C1608C0G1H270JT 27p 5% 50V C1608C0G1H270JT 27p 5% 50V C1608Y5V1C334ZT 330000p -20 C1608C0G1H270JT 27p 5% 50V C1608Y5V1C334ZT 330000p -20 0603B104K500CT 100000p 10% 0603B104K500CT 100000p 10% C1608C0G1H150JT 15p 5% 50V C1608C0G1H150JT 15p 5% 50V 0603B104K500CT 100000p 10% 0603B104K500CT 100000p 10% 0603B104K500CT 100000p 10% 0603B104K500CT 100000p 10% C1608C0G1H220JT 22p 5% 50V C1608C0G1H220JT 22p 5% 50V 0603B104K500CT 100000p 10% C1608C0G1H101JT 100p 5% 50V 0603B104K500CT 100000p 10% C1608C0G1H330JT 33p 5% 50V C1608C0G1H330JT 33p 5% 50V 0603B104K500CT 100000p 10% C1608C0G1H220JT 22p 5% 50V C1608C0G1H220JT 22p 5% 50V

*S *AL LOC. NO. C602 C603 C610 C611 C612 C613 C626 C7 C71 C72 C73 C750 C752 C753 C754 C759 C78 C8 C800 C801 C802 C803 C85 C9 C901 C902 C903 C904 C905 C906 C907 C964 C129 C130

PART NO. 0CC220CK41A 0CC220CK41A 0CC102CK41A 0CK473CK56A 0CK473CK56A 0CK473CK56A 0CK104CK56A 0CK104CK56A 0CK106EF56A 0CK106EF56A 0CK106EF56A 0CK104CK56A 0CK104CK56A 0CK104CK56A 0CC471CK41A 0CK104CK56A 0CK106EF56A 0CK104CK56A 0CK105CF94A 0CK105CF94A 0CK105CF94A 0CK105CF94A 0CC102CK41A 0CK104CK56A 0CK103CK51A 0CK103CK51A 0CK103CK51A 0CK103CK51A 0CK103CK51A 0CK103CK51A 0CK103CK51A 0CK105DK94A 181-007F 181-007F

DATE: 2006. 03.03. DESCRIPTION / SPECIFICATION C1608C0G1H220JT 22p 5% 50V C1608C0G1H220JT 22p 5% 50V C1608C0G1H102JT 1000p 5% 50 C1608X7R1H473KT 47000p 10% C1608X7R1H473KT 47000p 10% C1608X7R1H473KT 47000p 10% 0603B104K500CT 100000p 10% 0603B104K500CT 100000p 10% C3216X7R1C106KT 10000000p 1 C3216X7R1C106KT 10000000p 1 C3216X7R1C106KT 10000000p 1 0603B104K500CT 100000p 10% 0603B104K500CT 100000p 10% 0603B104K500CT 100000p 10% C1608C0G1H471JT 470p 5% 50V 0603B104K500CT 100000p 10% C3216X7R1C106KT 10000000p 1 0603B104K500CT 100000p 10% 0603F105Z160CT 1000000p -20 0603F105Z160CT 1000000p -20 0603F105Z160CT 1000000p -20 0603F105Z160CT 1000000p -20 C1608C0G1H102JT 1000p 5% 50 0603B104K500CT 100000p 10% 0603B103K500CT 10000p 10% 5 0603B103K500CT 10000p 10% 5 0603B103K500CT 10000p 10% 5 0603B103K500CT 10000p 10% 5 0603B103K500CT 10000p 10% 5 0603B103K500CT 10000p 10% 5 0603B103K500CT 10000p 10% 5 0805F105Z500CT 1000000p -20 ECQV1H224JZ3 0.22u 5% 50V M ECQV1H224JZ3 0.22u 5% 50V M

DIODEs
D100 D101 ZD1300 ZD1301 ZD901 D107 D711 D102 D103 IC751 IC754 D104 D105 D703 D704 ZD101 ZD215 ZD216 ZD217 ZD218 ZD219 ZD220 ZD222 ZD1000 D700 0DRFC00288A 0DRFC00288A 0DR340009AA 0DR340009AA 0DR340009AA 0DS226009AA 0DD184009AA 0DS181009AA 0DS181009AA 0DRSE00018B 0DRSE00018B 0DZ620009HB 0DZ620009HB 0DZ510009EE 0DZ510009EE 0DZ510009EE 0DZ510009EE 0DZ510009EE 0DZ510009EE 0DZ510009EE 0DZ510009EE 0DZ510009EE 0DZ510009EE 0DZ330009DF 0DZ510009EE SS14 500MV 40V 1A - - 1100M SS14 500MV 40V 1A - - 1100M MBRS340 525MV 40V 4A - - MBRS340 525MV 40V 4A - - MBRS340 525MV 40V 4A - - KDS226 1200MV 85V 300MA 2A KDS184 1200MV 85V 300MA 2A KDS181 1200MV 85V 300MA 2A KDS181 1200MV 85V 300MA 2A SRV05-4 1200MV 6V 17.5V 12A SRV05-4 1200MV 6V 17.5V 12A UDZS6.2B 6200MV 6.06TO6.33V UDZS6.2B 6200MV 6.06TO6.33V UDZS5.1B 5100MV 4.98TO5.2V UDZS5.1B 5100MV 4.98TO5.2V UDZS5.1B 5100MV 4.98TO5.2V UDZS5.1B 5100MV 4.98TO5.2V UDZS5.1B 5100MV 4.98TO5.2V UDZS5.1B 5100MV 4.98TO5.2V UDZS5.1B 5100MV 4.98TO5.2V UDZS5.1B 5100MV 4.98TO5.2V UDZS5.1B 5100MV 4.98TO5.2V UDZS5.1B 5100MV 4.98TO5.2V MTZJ33B 33V 30.32TO31.88V 6 UDZS5.1B 5100MV 4.98TO5.2V

- 28 -

*S *AL LOC. NO. D701 D702 D705 D706 ZD203 ZD204 ZD205 ZD206 ZD208 ZD210 ZD213 ZD214 ZD221 ZD5001 ZD5002 ZD5003 ZD851 ZD852

PART NO. 0DZ510009EE 0DZ510009EE 0DZ510009EE 0DZ510009EE 0DZ510009EE 0DZ510009EE 0DZ510009EE 0DZ510009EE 0DZ510009EE 0DZ510009EE 0DZ510009EE 0DZ510009EE 0DZ510009EE 0DZ510009EE 0DZ510009EE 0DZ510009EE 0DZ510009EE 0DZ510009EE

DATE: 2006. 03.03. DESCRIPTION / SPECIFICATION UDZS5.1B 5100MV 4.98TO5.2V UDZS5.1B 5100MV 4.98TO5.2V UDZS5.1B 5100MV 4.98TO5.2V UDZS5.1B 5100MV 4.98TO5.2V UDZS5.1B 5100MV 4.98TO5.2V UDZS5.1B 5100MV 4.98TO5.2V UDZS5.1B 5100MV 4.98TO5.2V UDZS5.1B 5100MV 4.98TO5.2V UDZS5.1B 5100MV 4.98TO5.2V UDZS5.1B 5100MV 4.98TO5.2V UDZS5.1B 5100MV 4.98TO5.2V UDZS5.1B 5100MV 4.98TO5.2V UDZS5.1B 5100MV 4.98TO5.2V UDZS5.1B 5100MV 4.98TO5.2V UDZS5.1B 5100MV 4.98TO5.2V UDZS5.1B 5100MV 4.98TO5.2V UDZS5.1B 5100MV 4.98TO5.2V UDZS5.1B 5100MV 4.98TO5.2V

*S *AL LOC. NO.

PART NO.

DATE: 2006. 03.03. DESCRIPTION / SPECIFICATION

COIL & CORE & INDUCTOR
L104 L105 L100 L1002 L3 L301 L302 L304 L311 L4 L4000 L401 L5 L500 L501 L502 L503 L504 L505 L600 L601 L602 L701 L800 L850 L900 L901 L902 L903 L202 L203 L204 L205 L207 L208 L209 L210 L4001 L5000 L603 L904 Z1000 L1 L1001 L11 L13 L14 L15 L17 L2 L402 L403 L7 L10 L12 L16 L200 L201 L306 L307 L8 6140TBZ045A 6140TBZ045A 6210TCE001G 6210TCE001G 6210TCE001G 6210TCE001A 6210TCE001A 6210TCE001G 6210TCE001G 6210TCE001G 6210TCE001G 6210TCE001G 6210TCE001G 6210TCE001G 6210TCE001G 6210TCE001G 6210TCE001G 6210TCE001G 6210TCE001G 6210TCE001G 6210TCE001G 6210TCE001G 6210TCE001G 6210TCE001G 6210TCE001G 6210TCE001G 6210TCE001G 6210TCE001G 6210TCE001G 6210TCE001A 6210TCE001A 6210TCE001A 6210TCE001A 6210TCE001A 6210TCE001A 6210TCE001A 6210TCE001A 6210TCE001G 6210TCE001G 6210TCE001A 6210TCE001G 6200QL3001Z 0LC1032101A 0LC1020101A 0LC1032101A 0LC1032101A 0LC1032101A 0LC1032101A 0LC1032101A 0LC1032101A 0LC1532101A 0LC1532101A 0LC1032101A 0LC1032101A 0LC1032101A 0LC1032101A 0LC1020101A 0LC1020101A 0LC1532101A 0LC1532101A 0LC1032101A 38.5uH - - 13.5X20MM LEAD 38.5uH - - 13.5X20MM LEAD HH-1M3216-501JT 500OHM 3.2X HH-1M3216-501JT 500OHM 3.2X HH-1M3216-501JT 500OHM 3.2X HB-1S2012-080JT 8OHM 2X1.25 HB-1S2012-080JT 8OHM 2X1.25 HH-1M3216-501JT 500OHM 3.2X HH-1M3216-501JT 500OHM 3.2X HH-1M3216-501JT 500OHM 3.2X HH-1M3216-501JT 500OHM 3.2X HH-1M3216-501JT 500OHM 3.2X HH-1M3216-501JT 500OHM 3.2X HH-1M3216-501JT 500OHM 3.2X HH-1M3216-501JT 500OHM 3.2X HH-1M3216-501JT 500OHM 3.2X HH-1M3216-501JT 500OHM 3.2X HH-1M3216-501JT 500OHM 3.2X HH-1M3216-501JT 500OHM 3.2X HH-1M3216-501JT 500OHM 3.2X HH-1M3216-501JT 500OHM 3.2X HH-1M3216-501JT 500OHM 3.2X HH-1M3216-501JT 500OHM 3.2X HH-1M3216-501JT 500OHM 3.2X HH-1M3216-501JT 500OHM 3.2X HH-1M3216-501JT 500OHM 3.2X HH-1M3216-501JT 500OHM 3.2X HH-1M3216-501JT 500OHM 3.2X HH-1M3216-501JT 500OHM 3.2X HB-1S2012-080JT 8OHM 2X1.25 HB-1S2012-080JT 8OHM 2X1.25 HB-1S2012-080JT 8OHM 2X1.25 HB-1S2012-080JT 8OHM 2X1.25 HB-1S2012-080JT 8OHM 2X1.25 HB-1S2012-080JT 8OHM 2X1.25 HB-1S2012-080JT 8OHM 2X1.25 HB-1S2012-080JT 8OHM 2X1.25 HH-1M3216-501JT 500OHM 3.2X HH-1M3216-501JT 500OHM 3.2X HB-1S2012-080JT 8OHM 2X1.25 HH-1M3216-501JT 500OHM 3.2X X6966D 36.125MHZ 13.7X2.4X4 FI-C3216-103KJT 10UH 10% FI-B2012-102KJT 1UH 10% - 1 FI-C3216-103KJT 10UH 10% FI-C3216-103KJT 10UH 10% FI-C3216-103KJT 10UH 10% FI-C3216-103KJT 10UH 10% FI-C3216-103KJT 10UH 10% FI-C3216-103KJT 10UH 10% FI-C3216-153KJT 15UH 10% FI-C3216-153KJT 15UH 10% FI-C3216-103KJT 10UH 10% FI-C3216-103KJT 10UH 10% FI-C3216-103KJT 10UH 10% FI-C3216-103KJT 10UH 10% FI-B2012-102KJT 1UH 10% - 1 FI-B2012-102KJT 1UH 10% - 1 FI-C3216-153KJT 15UH 10% FI-C3216-153KJT 15UH 10% FI-C3216-103KJT 10UH 10% -

IC
IC600 IC200 IC850 IC100 IC101 IC2000 IC4000 IC4003 IC4004 IC4006 IC702 IC752 IC4002 IC1300 IC1301 IC904 IC4005 IC749 IC753 IC907 IC918 IC901 IC2 IC300 IC4 IC4007 IC505 IC6 IC601 IC604 IC905 IC906 IC501 IC1 IC750 IC500 IC800 IC3 IC103 IC8 0IPRPM3002D 0ISA722200C 0IMCRMI006B 0IMCRMZ002A 0IMCRMZ002A 0ISTL00026A 0ISTLFA108A 0ISTLFA108A 0ISTLFA108A 0ISTL00021A 0ISTL00031A 0IMCRTI001A 0IPRPAK013A 0IPMG00063A 0IPMG00063A 0IPMG00063A 0IPRPJR017A 0IMMRSG036A 0IMMRSG036A 0IMCRAL006A 0IMCRAL006A 0IPRPGN014C 0IPMGFA061A 0IPMGKE039A 0IPMGFA061A 0IPMG00107A 0IPMGSG020A 0IPMGSG018D 0IPMGK2001B 0IPMG78341A 0IPMGFA061A 0IPMGSG018D 0IMMREB010A 0IPRPMN003G 0IMCRSG010A 0IMCRGN002E 0IPRPNP001A 0IKE702700D 0ISS780800J 0IMCRFA015A MST9883C-LF-110 3TO3.6V 2.2 "LA7222-(E),LF 8TO13V - - 35" M52758FP 4.75TO5.5V - - 106 MP7720 15TO24V - 0.04% 10W MP7720 15TO24V - 0.04% 10W MC14066BDR2G 3TO18V 0.001mA NC7SV125P5X 0.9TO3.6V 0.000 NC7SV125P5X 0.9TO3.6V 0.000 NC7SV125P5X 0.9TO3.6V 0.000 SN74AHCT1G125DCKR 4.5TO5.5V 74LV74PW 1TO5.5V 0.02mA D F SN74HCT157DR 4.5TO5.5V 0.00 AK4525VF-E2 4.5TO5.5V 3TO5. MP1593DN-LF-Z 4.75TO28V 1.2 MP1593DN-LF-Z 4.75TO28V 1.2 MP1593DN-LF-Z 4.75TO28V 1.2 NJU26901E2 2.25TO2.75V 1mA M24C02-WMN6TP 2KBIT 256X8BI M24C02-WMN6TP 2KBIT 256X8BI AT24C16AN-10SI-2.7 16KBIT 2 AT24C16AN-10SI-2.7 16KBIT 2 GM5221H-LF-BC 3.15TO3.45V 6 FAN1587AD33X 4.8TO10.3V 3.3 KIA78D09F 10TO25V 9V 1300MW FAN1587AD33X 4.8TO10.3V 3.3 AZ1117H-2.5TR/E1 15V 2.5V LD1117DT18TR 3.3TO8V 1.8V 1 LD1086DT18TR 30V 1.8V - DPA AIC1117A-33CYTR(BS33) 2.65T "AZ1085S-3.3TR/E1,LF 12V 3.3" FAN1587AD33X 4.8TO10.3V 3.3 LD1086DT18TR 30V 1.8V - DPA M12L64322A-6T 64MBIT 512MX3 "VCT49X3F-F2,LF 7600MVTO8700" ST3232CDR 3.0TO5.5 - SOP R/ FLI2300CF 1800MVTO3300MV SM5301BS-G-ET 4500MVTO5500M KIA7027AF -0.3TO15V 2.7V 50 KA78M08RTM 10.5TO23V 8V - D KA7805R 7TO20V 5V 150W DPAK

- 29 -

*S *AL LOC. NO. L9 L130