Text preview for : MFL30105507_0.pdf part of LG 37LC2R / 42LC2R LCD TV Service Manual
Back to : MFL30105507_0.pdf | Home
website:http://biz.LGservice.com e-mail:http://www.LGEservice.com/techsup.html
LCD TV SERVICE MANUAL
CHASSIS : LP62C FACTORY MODEL : 37LC2R-TH / 42LC2R-TH
MODEL : 37LC2R / 42LC2R
CAUTION
BEFORE SERVICING THE CHASSIS, READ THE SAFETY PRECAUTIONS IN THIS MANUAL.
R
CONTENTS
CONTENTS .............................................................................................. 2 SAFETY PRECAUTIONS ..........................................................................3 SPECIFICATION ........................................................................................6 ADJUSTMENT INSTRUCTION................................................................11 TROUBLE SHOOTING ............................................................................16 BLOCK DIAGRAM...................................................................................25 EXPLODED VIEW .................................................................................. 25 REPLACEMENT PARTS LIST ............................................................... 28 SVC. SHEET ...............................................................................................
-2-
SAFETY PRECAUTIONS
IMPORTANT SAFETY NOTICE
Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in the Schematic Diagram and Replacement Parts List. It is essential that these special safety parts should be replaced with the same components as recommended in this manual to prevent X-RADIATION, Shock, Fire, or other Hazards. Do not modify the original design without permission of manufacturer.
General Guidance
An isolation Transformer should always be used during the servicing of a receiver whose chassis is not isolated from the AC power line. Use a transformer of adequate power rating as this protects the technician from accidents resulting in personal injury from electrical shocks. It will also protect the receiver and it's components from being damaged by accidental shorts of the circuitry that may be inadvertently introduced during the service operation. If any fuse (or Fusible Resistor) in this TV receiver is blown, replace it with the specified. When replacing a high wattage resistor (Oxide Metal Film Resistor, over 1W), keep the resistor 10mm away from PCB. Keep wires away from high voltage or high temperature parts.
Before returning the receiver to the customer,
always perform an AC leakage current check on the exposed metallic parts of the cabinet, such as antennas, terminals, etc., to be sure the set is safe to operate without damage of electrical shock.
Leakage Current Cold Check(Antenna Cold Check)
With the instrument AC plug removed from AC source, connect an electrical jumper across the two AC plug prongs. Place the AC switch in the on position, connect one lead of ohm-meter to the AC plug prongs tied together and touch other ohm-meter lead in turn to each exposed metallic parts such as antenna terminals, phone jacks, etc. If the exposed metallic part has a return path to the chassis, the measured resistance should be between 1M and 5.2M. When the exposed metal has no return path to the chassis the reading must be infinite. An other abnormality exists that must be corrected before the receiver is returned to the customer.
Leakage Current Hot Check (See below Figure)
X-RAY Radiation
Warning:
The source of X-RAY RADIATION in this TV receiver is the High Voltage Section and the LCD PANEL. For continued X-RAY RADIATION protection, the replacement panel must be the same type panel as specified in the Replacement Parts List.
To determine the presence of high voltage, use an accurate high impedance HV meter. Adjust brightness, color, contrast controls to minimum. Measure the high voltage. The meter reading should indicate 23.5 1.5KV: 14-19 inch, 26 1.5KV: 19-21 inch, 29.0 1.5KV: 25-29 inch, 30.0 1.5KV: 32 inch If the meter indication is out of tolerance, immediate service and correction is required to prevent the possibility of premature component failure.
Plug the AC cord directly into the AC outlet. Do not use a line Isolation Transformer during this check. Connect 1.5K/10watt resistor in parallel with a 0.15uF capacitor between a known good earth ground (Water Pipe, Conduit, etc.) and the exposed metallic parts. Measure the AC voltage across the resistor using AC voltmeter with 1000 ohms/volt or more sensitivity. Reverse plug the AC cord into the AC outlet and repeat AC voltage measurements for each exposed metallic part. Any voltage measured must not exceed 0.75 volt RMS which is corresponds to 0.5mA. In case any measurement is out of the limits specified, there is possibility of shock hazard and the set must be checked and repaired before it is returned to the customer.
Leakage Current Hot Check circuit
AC Volt-meter
To Instrument's exposed METALLIC PARTS
0.15uF
Good Earth Ground such as WATER PIPE, CONDUIT etc.
1.5 Kohm/10W
-3-
SERVICING PRECAUTIONS
CAUTION: Before servicing receivers covered by this service manual and its supplements and addenda, read and follow the SAFETY PRECAUTIONS on page 3 of this publication. NOTE: If unforeseen circumstances create conflict between the following servicing precautions and any of the safety precautions on page 3 of this publication, always follow the safety precautions. Remember: Safety First. General Servicing Precautions 1. Always unplug the receiver AC power cord from the AC power source before; a. Removing or reinstalling any component, circuit board module or any other receiver assembly. b. Disconnecting or reconnecting any receiver electrical plug or other electrical connection. c. Connecting a test substitute in parallel with an electrolytic capacitor in the receiver. CAUTION: A wrong part substitution or incorrect polarity installation of electrolytic capacitors may result in an explosion hazard. 2. Test high voltage only by measuring it with an appropriate high voltage meter or other voltage measuring device (DVM, FETVOM, etc) equipped with a suitable high voltage probe. Do not test high voltage by "drawing an arc". 3. Do not spray chemicals on or near this receiver or any of its assemblies. 4. Unless specified otherwise in this service manual, clean electrical contacts only by applying the following mixture to the contacts with a pipe cleaner, cotton-tipped stick or comparable non-abrasive applicator; 10% (by volume) Acetone and 90% (by volume) isopropyl alcohol (90%-99% strength) CAUTION: This is a flammable mixture. Unless specified otherwise in this service manual, lubrication of contacts in not required. 5. Do not defeat any plug/socket B+ voltage interlocks with which receivers covered by this service manual might be equipped. 6. Do not apply AC power to this instrument and/or any of its electrical assemblies unless all solid-state device heat sinks are correctly installed. 7. Always connect the test receiver ground lead to the receiver chassis ground before connecting the test receiver positive lead. Always remove the test receiver ground lead last. 8. Use with this receiver only the test fixtures specified in this service manual. CAUTION: Do not connect the test fixture ground strap to any heat sink in this receiver. Electrostatically Sensitive (ES) Devices Some semiconductor (solid-state) devices can be damaged easily by static electricity. Such components commonly are called Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and semiconductor "chip" components. The following techniques should be used to help reduce the incidence of component damage caused by static by static electricity. 1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any electrostatic charge on your body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging wrist strap device, which should be removed to prevent potential shock reasons prior to applying power to the unit under test. 2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as aluminum foil, to prevent electrostatic charge buildup or exposure of the assembly. 3. Use only a grounded-tip soldering iron to solder or unsolder ES devices. 4. Use only an anti-static type solder removal device. Some solder removal devices not classified as "anti-static" can generate electrical charges sufficient to damage ES devices. 5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices. 6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or comparable conductive material). 7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material to the chassis or circuit assembly into which the device will be installed. CAUTION: Be sure no power is applied to the chassis or circuit, and observe all other safety precautions. 8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity sufficient to damage an ES device.) General Soldering Guidelines 1. Use a grounded-tip, low-wattage soldering iron and appropriate tip size and shape that will maintain tip temperature within the range or 500 F to 600 F. 2. Use an appropriate gauge of RMA resin-core solder composed of 60 parts tin/40 parts lead. 3. Keep the soldering iron tip clean and well tinned. 4. Thoroughly clean the surfaces to be soldered. Use a mall wirebristle (0.5 inch, or 1.25cm) brush with a metal handle. Do not use freon-propelled spray-on cleaners. 5. Use the following unsoldering technique a. Allow the soldering iron tip to reach normal temperature. (500 F to 600 F) b. Heat the component lead until the solder melts. c. Quickly draw the melted solder with an anti-static, suctiontype solder removal device or with solder braid. CAUTION: Work quickly to avoid overheating the circuitboard printed foil. 6. Use the following soldering technique. a. Allow the soldering iron tip to reach a normal temperature (500 F to 600 F) b. First, hold the soldering iron tip and solder the strand against the component lead until the solder melts. c. Quickly move the soldering iron tip to the junction of the component lead and the printed circuit foil, and hold it there only until the solder flows onto and around both the component lead and the foil. CAUTION: Work quickly to avoid overheating the circuit board printed foil. d. Closely inspect the solder area and remove any excess or splashed solder with a small wire-bristle brush.
-4-
IC Remove/Replacement Some chassis circuit boards have slotted holes (oblong) through which the IC leads are inserted and then bent flat against the circuit foil. When holes are the slotted type, the following technique should be used to remove and replace the IC. When working with boards using the familiar round hole, use the standard technique as outlined in paragraphs 5 and 6 above. Removal 1. Desolder and straighten each IC lead in one operation by gently prying up on the lead with the soldering iron tip as the solder melts. 2. Draw away the melted solder with an anti-static suction-type solder removal device (or with solder braid) before removing the IC. Replacement 1. Carefully insert the replacement IC in the circuit board. 2. Carefully bend each IC lead against the circuit foil pad and solder it. 3. Clean the soldered areas with a small wire-bristle brush. (It is not necessary to reapply acrylic coating to the areas). "Small-Signal" Discrete Transistor Removal/Replacement 1. Remove the defective transistor by clipping its leads as close as possible to the component body. 2. Bend into a "U" shape the end of each of three leads remaining on the circuit board. 3. Bend into a "U" shape the replacement transistor leads. 4. Connect the replacement transistor leads to the corresponding leads extending from the circuit board and crimp the "U" with long nose pliers to insure metal to metal contact then solder each connection. Power Output, Transistor Device Removal/Replacement 1. Heat and remove all solder from around the transistor leads. 2. Remove the heat sink mounting screw (if so equipped). 3. Carefully remove the transistor from the heat sink of the circuit board. 4. Insert new transistor in the circuit board. 5. Solder each transistor lead, and clip off excess lead. 6. Replace heat sink. Diode Removal/Replacement 1. Remove defective diode by clipping its leads as close as possible to diode body. 2. Bend the two remaining leads perpendicular y to the circuit board. 3. Observing diode polarity, wrap each lead of the new diode around the corresponding lead on the circuit board. 4. Securely crimp each connection and solder it. 5. Inspect (on the circuit board copper side) the solder joints of the two "original" leads. If they are not shiny, reheat them and if necessary, apply additional solder. Fuse and Conventional Resistor Removal/Replacement 1. Clip each fuse or resistor lead at top of the circuit board hollow stake. 2. Securely crimp the leads of replacement component around notch at stake top. 3. Solder the connections. CAUTION: Maintain original spacing between the replaced component and adjacent components and the circuit board to prevent excessive component temperatures.
Circuit Board Foil Repair Excessive heat applied to the copper foil of any printed circuit board will weaken the adhesive that bonds the foil to the circuit board causing the foil to separate from or "lift-off" the board. The following guidelines and procedures should be followed whenever this condition is encountered. At IC Connections To repair a defective copper pattern at IC connections use the following procedure to install a jumper wire on the copper pattern side of the circuit board. (Use this technique only on IC connections). 1. Carefully remove the damaged copper pattern with a sharp knife. (Remove only as much copper as absolutely necessary). 2. carefully scratch away the solder resist and acrylic coating (if used) from the end of the remaining copper pattern. 3. Bend a small "U" in one end of a small gauge jumper wire and carefully crimp it around the IC pin. Solder the IC connection. 4. Route the jumper wire along the path of the out-away copper pattern and let it overlap the previously scraped end of the good copper pattern. Solder the overlapped area and clip off any excess jumper wire. At Other Connections Use the following technique to repair the defective copper pattern at connections other than IC Pins. This technique involves the installation of a jumper wire on the component side of the circuit board. 1. Remove the defective copper pattern with a sharp knife. Remove at least 1/4 inch of copper, to ensure that a hazardous condition will not exist if the jumper wire opens. 2. Trace along the copper pattern from both sides of the pattern break and locate the nearest component that is directly connected to the affected copper pattern. 3. Connect insulated 20-gauge jumper wire from the lead of the nearest component on one side of the pattern break to the lead of the nearest component on the other side. Carefully crimp and solder the connections. CAUTION: Be sure the insulated jumper wire is dressed so the it does not touch components or sharp edges.
-5-
SPECIFICATION
NOTE : Specifications and others are subject to change without notice for improvement.
1. Application range
This specification is applied to LP62C chassis.
3. Test method
3.1 Performance : LGE TV test method followed 3.2 Demanded other specification Safety : CE, IEC Specification EMC : CE, IEC
2. Requirement for Test
Testing for standard of each part must be followed in below condition. (1) Temperature : 25°C±5°C(77±9°F), CST : 40±5 (2) Humidity : 65%±10% (3) Power : Standard input voltage (AC 100-240V, 50/60Hz) *Standard Voltage of each products is marked by models (4) Specification and performance of each parts are followed each drawing and specification by part number in accordance with BOM. (5) The receiver must be operated for about 20 minutes prior to the adjustment.
4. General TV Specification
No 1. 2. Item Video input applicable system Receivable Broadcasting System NTSC 4.43 1) PAL/SECAM BG 2) PAL/SECAM DK 3) PAL I/I 4) SECAM L/L' 5) PAL-N/M 6) NTSC M 3. RF Input Channel VHF : E2 ~ E12 UHF : E21 ~ E69 CATV : S1 ~ S20 HYPER : S21~ S47 L/L' : B, C, D VHF : 2~13 UHF : 14~69 CATV : 1~125 4. 5. 6. 7. 8. 9. 10. Input Voltage Market Active Screen Size Tuning System Operating Environment Storage Environment Display AC 100 ~ 240 V/50Hz, 60Hz Worldwide 940.3 mm(diagonal) 1067.308 mm (diagonal) FVS 100 program FS 1) Temp : 0 ~ 40 deg 2) Humidity : 10 ~ 90 %RH 1) Temp : -20 ~ 50 deg 2) Humidity : 10 ~ 90 %RH LCD Module 32"/42" : LPL 37" : AUO, LPL 37.02 inches 42.02 inches FRANCE NTSC only TH PAL only ZH Specification PAL-D/K, B/G, I, NTSC-M, SECAM, Remark
-6-
5. General Specification
No 1 2 3 Panel Frequency range Control Function Item Specification 37", 42" TFT WXGA LCD H : 31 ~ 61KhzV : 56 ~ 75Hz 1) Contrast/Brightness 2) H-Position / V-Position 3) Tracking : Clock / Phase 4) Auto Configure 5) Reset 4 5 Component Jack (480i/576i/480p/576p/720p/1080i) Power ON Y/Pb/Pr : 1EA Y/Pb/Pr : 2EA LED White Stand by 6 LCD Module Outline Dimension Pixel Pitch Pixel Format Coating Back Light 37" 42" 37" 42" 37" 42" RED Power consumption 190W(37") 230W(42") 1W (H)mmx(V)mmx(D)mm 877.0 x 516.8 x 55.5 1006 x 610 x 56 0.200 x 0.600 x RGB 0.227 x 0.681 x RGB 1366 x 768 Pixels RGB strip arrangement Hard coating(3H), Anti-glare treatment of the front polarizer, 16CCFL 20CCFL ZH TH PC Input Remark
6. Set Optical Feature
6.1. 37LC2R-TH/42LC2R-TH
No 1. Parameter Contrast Ratio CR Symbol Min 37" 42" 2. Surface Luminance, white 3. White Coordinate Normal Cool Warm 4. Color Temperature Normal Warm Cool 5. 6. Color pull in Range Color killer Sensitivity PAL NTSC X axis Y axis X axis Y axis X axis Y axis 0.280 0.295 0.271 0.283 0.300 0.316 8300 6200 10000 -500 -500 0.283 0.298 0.274 0.286 0.303 0.319 9300 7200 11000 0.286 0.301 0.277 0.289 0.306 0.322 10300 8200 12000 +500 +500 -80 Hz Hz dBm - 85IRE Full White Pattern - APC : Standard LWH 360 800 700 450 Value Typ 1200 1000 Max (*) Normal Mode - 100IRE Full white window pattern - APC : Clear (Dynamic) Cd/m2 (*) Normal Mode - 100IRE Full white window pattern - APC : Clear (Dynamic) - 85IRE Full White Pattern - APC : Standard Unit Remark
-7-
6.2. 37LC2R-TH/37LC2R-ZH(Only AUO Module)
No 1. Parameter Contrast Ratio CR Symbol Min 32", 37" 42" 2. Surface Luminance, white 3. White Coordinate Normal Cool Warm 4. Color Temperature Normal Warm Cool 5. 6. Color pull in Range Color killer Sensitivity PAL NTSC X axis Y axis X axis Y axis X axis Y axis 0.280 0.295 0.271 0.283 0.300 0.316 8300 6200 10000 -500 -500 0.283 0.298 0.274 0.286 0.303 0.319 9300 7200 11000 0.286 0.301 0.277 0.289 0.306 0.322 10300 8200 12000 +500 +500 -80 Hz Hz dBm - 85IRE Full White Pattern - APC : Standard LWH 360 800 700 450 Value Typ 1200 1000 Cd/m2 Max (*) Normal Mode - 100IRE Full white window pattern - APC : Clear (Dynamic) (*) Normal Mode - 100IRE Full white window pattern - APC : Clear (Dynamic) - 85IRE Full White Pattern - APC : Standard Unit Remark
7. Model Specification
No 1. 2. 3. Market Broadcasting system Available Channel Item N-EU PAL BG/I/DK, NTSC-M BAND VHF/UHF CATV 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. Receiving system SCART Jack(0EA) Video Input (2EA) S-Video Input (2EA) Component Input (1EA) RGB Input (1EA) HDMI Input (2EA) Audio Input (4EA) Wired Control (1EA) Audio variable out(1EA) PAL C1 ~ C69 S1 ~ S47 NTSC 2~83 1~71 Specification Remark
Upper Heterodyne PAL, SECAM, NTSC PAL, SECAM, NTSC PAL, SECAM, NTSC Y/Cb/Cr, Y/ Pb/Pr RGB-PC, RGB-DTV HDMI-PC HDMI-DTV PC Audio, Component (1EA), AV (2EA) L/R Input 4 System : PAL, SECAM, NTSC, PAL60 4 System : PAL, SECAM, NTSC, PAL60
-8-
8. Component Video Input (Y, PB, PR)
No 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. Resolution 720 x 480 720 x 480 720 x 576 720 x 480 720 x 480 720 x 576 1280 x 720 1280 x 720 1280 x 720 1920 x 1080 1920 x 1080 1920 x 1080 H-freq(kHz) 15.73 15.75 15.625 31.47 31.50 31.25 44.96 45.00 37.50 33.72 33.75 28.125 V-freq.(kHz) 59.94 60.00 50.00 59.94 60.00 50.00 59.94 60.00 50.00 59.94 60.00 50.00 Pixel clock(MHz) 13.500 13.514 13.500 27.000 27.027 27.000 74.176 74.250 74.25 74.176 74.250 74.250 Remarks SDTV, DVD 480I(525I) SDTV, DVD 480I(525I) SDTV, DVD 576I(625I) SDTV 480P SDTV 480P SDTV 576P HDTV 720P HDTV 720P HDTV 720P 50Hz HDTV 1080I HDTV 1080I HDTV 1080I 50Hz
9. RGB Input ( PC )
No 1 2. 3 4 5 6 7 8 9 10 11 12 Resolution 720 x 400 640 x 480 640 x 480 800 x 600 800 x 600 832 x 624 1024 x 768 1024 x 768 1024 x 768 1280 x 768 1360 x 768 1366 x 768 H-freq(kHz) 31.469 31.469 37.500 37.879 46.875 49.725 48.363 56.476 60.023 47.693 47.700 47.700 V-freq.(kHz) 70.08 59.94 75.00 60.31 75.00 74.55 60.00 70.06 75.02 59.99 60.00 60.00 Pixel clock(MHz) 28.32 25.17 31.50 40.00 49.50 57.28 65.00 75.00 78.75 80.125 84.62 84.62 DOS VESA(VGA) VESA(VGA) VESA(SVGA) VESA(SVGA) Macintosh VESA(XGA) VESA(XGA) VESA(XGA) WXGA(42XGA,50", 60") WXGA(42XGA,50", 60") WXGA(42XGA,50", 60") Remarks
10. RGB input ( DTV )
No 1. 2. 3. 4. 5. 6. 7. 8. 9. Resolution 720 x 480 720 x 480 720 x 576 1280 x 720 1280 x 720 1280 x 720 1920 x 1080 1920 x 1080 1920 x 1080 H-freq(kHz) 31.47 31.50 31.25 44.96 45.00 37.50 33.72 33.75 28.125 V-freq.(kHz) 59.94 60.00 50.00 59.94 60.00 50.00 59.94 60.00 50.00 Pixel clock(MHz) 27.000 27.027 27.000 74.176 74.250 74.25 74.176 74.250 74.250 SDTV 480P SDTV 480P SDTV 576P HDTV 720P HDTV 720P HDTV 720P 50Hz HDTV 1080I HDTV 1080I HDTV 1080I 50Hz Remarks
-9-
11. HDMI Input ( PC )
No 1 2 3 4 5 6. 7 8 9 10 11 12 Resolution 720 x 400 640 x 480 640 x 480 800 x 600 800 x 600 832 x 624 1024 x 768 1024 x 768 1024 x 768 1280 x 768 1360 x 768 1366 x 768 H-freq(kHz) 31.469 31.469 37.500 37.879 46.875 49.725 48.363 56.476 60.023 47.693 47.700 47.700 V-freq.(kHz) 70.08 59.94 75.00 60.31 75.00 74.55 60.00 70.06 75.02 59.99 60.00 60.00 Pixel clock(MHz) 28.32 25.17 31.50 40.00 49.50 57.28 65.00 75.00 78.75 80.125 84.62 84.62 DOS VESA(VGA) VESA(VGA) VESA(SVGA) VESA(SVGA) Macintosh VESA(XGA) VESA(XGA) VESA(XGA) WXGA(42XGA,50", 60") WXGA(42XGA,50", 60") WXGA(42XGA,50", 60") Remarks
12. HDMI input ( DTV )
No 1. 2. 3. 4. 5. 6. 7. 8. 9. Resolution 720 x 480 720 x 480 720 x 576 1280 x 720 1280 x 720 1280 x 720 1920 x 1080 1920 x 1080 1920 x 1080 H-freq(kHz) 31.47 31.50 31.25 44.96 45.00 37.50 33.72 33.75 28.125 V-freq.(kHz) 59.94 60.00 50.00 59.94 60.00 50.00 59.94 60.00 50.00 Pixel clock(MHz) 27.000 27.027 27.000 74.176 74.250 74.25 74.176 74.250 74.250 SDTV 480P SDTV 480P SDTV 576P HDTV 720P HDTV 720P HDTV 720P 50Hz HDTV 1080I HDTV 1080I HDTV 1080I 50Hz Remarks
13. Mechanical Specification
13.1. 37LC2R
No 1. Product Dimension 2. ProductWeight Before Packing After Packing Only SET With BOX Item Width 944 1052 286 383 31 33.3 Content Length Height 726 855 Unit mm mm Kg Kg SET(With Stand) Remark
13.2. 42LC2R
No 1. Product Dimension 2. ProductWeight Before Packing After Packing Only SET With BOX Item Width 1054 1166 286 402 37 42.3 Content Length Height 813.5 950 Unit mm mm Kg Kg SET(With Stand) Remark
- 10 -
ADJUSTMENT INSTRUCTION
1. Application Range
This spec. sheet is applied to all of the LP62A/B/C chassis(H3-High) manufactured at LG TV Plant all over the world.
4. EDID
Caution * Use the proper signal cable for EDID Download - Analog EDID : Pin3 exists - Digital EDID : Pin3 exists => Caution: - Never connect HDMI & DVI-D & DVI-A Cable at the same time. - Use the proper cables below for EDID Writing
2. Specification
2.1 Because this is not a hot chassis, it is not necessary to use an isolation transformer. However, the use of isolation transformer will help to protect test instruments. 2.2 Adjustment must be done in the correct sequence. 2.3 The adjustment must be performed at 25±5°C temperature and 65±10% relative humidity if there is no specified designation. 2.4 The input voltage of the receiver must be kept between 100~220V, 50/60Hz. 2.5 Before adjustment, execute Heat-Run for 30 minutes at RF no signal
4.1 EDID Data
4.1.1. ANALOG(256 Bytes ) · BLOCK1 (128BYTE) 00 10 20 30 40 50 60 70 00 01 00 FF c 11 49 61 40 35 00 40 80 4B 1F 02 FF 01 4B 01 BC 37 3D 03 FF 03 A5 01 88 00 09 04 FF 01 6E 01 21 BC 00 05 FF 46 80 01 00 88 0A 06 07 FF 00 27 78 31 40 1B 21 00 1C 21 00 20 20 d 08 1E EA 01 50 4E 00 20 09 6D D9 01 A0 1F 18 20 0A 0B a B0 A3 01 01 51 00 00 80 00 00 20 20 0C 0D 0E b 57 49 9C 45 40 01 1E 30 48 51 00 1E 00 FD 00 d 00 0F 25 01 88 30 38 99
3. Adjustment items
3.1 PCB assembly adjustment items
· Channel memory - Download the channel data from BOM to EEPROM by using LGIDS. · Option adjustment following BOM - Tool Option1 - Tool Option2 - Area Option
4.1.2. HDMI(256 Bytes ) · BLOCK1 (128BYTE) 00 10 20 30 40 50 60 70 05 06 FF FF 46 27 80 31 01 1B 00 00 88 21 d 00 38 4B 1F 3D 09 00 BLOCK2 (128BYTE) 00 10 20 30 40 50 60 70 00 02 07 0C BC 96 28 16 00 01 03 07 00 88 00 60 20 00 02 24 23 10 21 13 35 58 00 03 F1 09 00 00 8E 00 2C 00 04 49 07 01 00 21 00 25 00 05 85 07 1D 1E 00 00 00 00 06 04 23 00 8C 00 32 C4 00 07 02 09 80 0A 18 00 8E 00 08 01 07 51 D0 2A 00 21 00 09 03 07 D0 8A 12 1C 00 00 0A 11 83 1C 20 00 01 00 00 0B 12 01 20 E0 10 1D 9E 00 0C 13 00 40 2D 41 80 00 00 0D 14 00 80 10 43 18 00 00 0E 23 65 35 10 17 71 00 00 0F 09 03 00 3E 20 1C 00 6B 00 01 00 FF c 11 49 61 40 35 00 40 80 02 FF 01 4B 01 BC 37 03 FF 03 A5 01 88 00 04 FF 80 6E 01 21 BC 07 00 78 40 21 1C 00 0C 0D 0E b 57 49 9C 45 40 01 1E 30 48 51 00 1E d 00 00 00 0A 20 20 20 20 20 20 01 08 1E EA 01 50 4E 00 09 6D D9 01 A0 1F 18 0A 0B a B0 A3 01 01 51 00 00 80 0F 25 01 88 30 FD 14
LP62x
Cortez Version Panel Used XX hr. Tool Option1 Tool Option2 Area Option : : x.xx 7 161 16
(Fig. 1) 1) Push the ADJ key in the Adjust Remocon. 2) Input the Option Number that was specified in the BOM, into the Shipping area. 3) Select "Tool Option1/ Tool Option2/ Area Option" by using / (CH+/-) key , and press the number key(0~9) consecutively ex) If the value of Tool Option1 is 7, input the data using number key "7" (Fig. 1)
3.2 SET assembly adjustment items
· Auto AV(ZH-AV3, TH-AV1) Color Balance · Aging (by Power on key) · Adjustment of White Balance · Auto Component Color Balance adjustment - Standard equipment : MSPG925FA · Auto RGB Color Balance adjustment - Standard equipment : MSPG925FA
=> Detail EDID Options are below (a, b, c, d, e) a. Product ID Product ID Model Name Product ID 37LC2R 42LC2R 30059(A) 30060(D) 40023(A) 40024(D) Dec 30059 30060 40023 40024 Hex 756B 756C 9C57 9C58 EDID table 6B75 6C75 579C 589C
b. Serial No : Controlled on production line c. Month, Year : Controlled on production line: ex) Montly : '03' => '03' Year : '2005' => '0F'
- 11 -
d. Model Name/Monitor Name: Model Name 37LC2R-TH 00 00 00 FC 00 33 37 4C 43 32 52 2D 54 48 0A 20 20 20 42LC2R-TH 00 00 00 FC 00 34 32 4C 43 32 52 2D 54 48 0A 20 20 20 e. Checksum: Changeable by total EDID data
Master pattern generator like MSPG-925) - If Minimum Black Level and/or Maximum White Level is not correct, Do select 100% Color Bar Pattern.
5. ADC Calibration
5.1 Adjustment of RF/AV/S-VIDEO
* Required Equipments · Remote controller for adjustment · 802F Pattern Generator, Master (MSPG-925FA), etc. · MSPG-925FA Pattern Generator (Which has Video Signal: 100% Color Bar Pattern shown in Fig. 1) = Model : 202 / Pattern: 33 (PAL : ZH, TH) > Model : 201 / Pattern : 33 (NTSC : MH) (Fig. 2) 5.2.1 Method of Auto Component Color Balance 1) Input the Component 720p 100% Color Bar(MSPG-925FA model:217, pattern:33) signal into Component. (ZH : component , TH/MH : component 1 or 2) 2) Set the PSM to Standard mode in the Picture menu. 3) Press the INSTART key on R/C for adjustment. 4) Press the (Vol. +) key to operate the set , then it becomes automatically. 5) Auto-RGB OK means the adjustment is completed.
5.3 Adjustment of RGB
* Required Equipments · Remote controller for adjustment (Fig. 1) 5.1.1 Method of Auto RF/AV/S-VIDEO Color Balance. 1) Press the FRONT-AV KEY on R/C for converting input mode. 2) Input the Video Signal: 100% Color Bar signal into AV3(ZH), AV1(TH), VIDEO1(MH) 3) Set the PSM to Standard mode in the Picture menu. 4) Press INSTART key on R/C for adjustment. 5) Press the (Vol.+) key to operate the set, then it becomes automatically 6) Auto-RGB OK means the adjustment is completed 5.1.2 Requirement · This AV color balance adjustment should be performed before White Balance Adjustment. · After color balance adjustment, You must push "power on" key. ("Power on" key is "Access Heat_run mode") · 802F Pattern Generator, Master (MSPG-925FA), etc. · MSPG-925FA Pattern Generator (Which has XGA [1024x768] 60Hz PC Format output signal : 100% Color Bar Pattern shown in Fig. 3 ) · It is very import to use correct adjustment pattern like Fig. 10. - Within the pattern, color sequence should be aligned : W-Y-C-G-M-R-BLUE-BLACK (If color sequence is reversed (Black ->...-> White), reverse the pattern with REV key, when using Master pattern generator like MSPG-925) - If Minimum Black Level and/or Maximum White Level is not correct, Do select 100% Color Bar Pattern.
5.2 Adjustment of Component.
* Required Equipments · Remote controller for adjustment · 802F Pattern Generator, Master (MSPG-925FA), etc. · MSPG-925FA Pattern Generator (Which has 720p YPbPr signal : 100% Color Bar Pattern shown in Fig. 2 ) = Model: 217 / Pattern: 33 > · It is very import to use correct adjustment pattern like Fig. 2. - Within the pattern, color sequence should be aligned : W-Y-C-G-M-R-BLUE-BLACK (If color sequence is reversed (Black -> ... -> White), reverse the pattern with REV key, when using (Fig. 3) 5.3.1 Method of Auto RGB Color Balance 1) Input the PC 1024x768@60Hz 1/2 Black&White Pattern (MSPG-925FA model:3, pattern:33) into RGB. 2) Set the PSM to Standard mode in Picture menu. 3) Press the INSTART key on R/C for adjustment. 4) Press the (Vol. +) key operate To set , then it becomes automatically. 5) Auto-RGB OK means adjustment is completed.
- 12 -
=> Caution : Before White-balance, the AV ADC should be done. (ZH:AV3, TH:AV1, MH:VIDEO1) => After Aging, When the procedure is changed White balance adjustment, it will be canceled Heat_run mode auto. (Notice : Before White-balance, change input mode Move to AV3(ZH) or AV1(TH) or VIDEO1(MH) by using the FRONT-AV KEY on Remote controller.)
6.2 Auto white Balance (AV)
1) LPL Module Data Command1 Command2 Set ID Input Select R-Gain G-Gain B-Gain R-Offset XB J J J J J J B A B C D E F 00 00 00 00 00 00 00 Min 00h 00h 00h 00h 00h 00h 00h Max 90h E0h E0h E0h 90h 90h 90h
6. White Balance
White balance MSPG925FA 216 Level (85IRE) Full screen pattern ZH(AV3), TH(AV1) Model : 202 · Pal Video MH(VIDEO1) Model : 201 · NTSC Video
G-Offset B-Offset 2) AUO Module
=> Caution : - System control RS-232 Host should be "PC" for adjustment. - AV ADC(ZH: AV3, TH : AV1, MH: VIDEO1) should be done before White-balance. * Test Equipment Color Analyzer (CA-110) PC(For communication through RS-232C)=>UART Baud rate : 115200 Pattern Generator (MSPG-925FA etc.) *Target Value [ PSM: Standard(ZH/TH), CSM: Normal] - Normal(9300K±1000K) x:283±0.015, y: 298±0.015 -Luminance(Y) AV/COMP: 250 Cd/m2 (Typ: 300 Cd/m2) PC : 300 Cd/m2 (Typ: 350 Cd/m2) => Reference Value(Automatically fixed) - Cool(11000K±1000K) - Warm(7200K±1000K)
Data Command1 Command2 Set ID Input Select R-Gain G-Gain B-Gain R-Offset G-Offset B-Offset XB J J J J J J B A B C D E F 00 00 00 00 00 00 00 Min 00h 00h 00h 00h 00h 00h 00h Max 90h E0h E0h E0h 90h 90h 90h
6.1 Manual white Balance (AV)
1) Execute CA-110 Zero Calibration. 2) Execute the SET Heat Run for 30minutes 3) As below Fig. 4, Supply 216Level (85 IRE) full screen pattern to Video input. 37LC2R-ZH,42LC2R-ZH : AV3/AV4 (Input 50Hz), 32LB1R-TH : AV1/AV2 (Input 50Hz) 4) Press the FRONT-AV KEY on R/C for converting input mode. 5) Set the PSM to Standard mode in Picture menu. 6) Enter the White Balance adjustment mode by pressing the INSTART key twice(White Balance) on R/C. 7) Stick sensor to center of the screen and select each items (Red/Green/Blue Gain and Offset) using / (CH+/-) key on R/C. 8)Adjust Only High Light with R Gain/B Gain using / (VOL +/-) key on R/C. 9) Adjust it until color coordination becomes as below. X-axis : 0.283±0.003 Y-axis : 0.298±0.003 (R/G/B gain and R/G/B offset Default values are different in according to using module ) 10) Adjust High light with R/B Gain.
216 Level(85IRE)
(Fig.4)
- 13 -
7. Shipping Conditions
No 1 2 3 4 5 6 7 Power Volume Level Main Picture Input Main Last Channel Mute ARC Station Auto Programme Manual Programme Programme Edit Favorite Programme 8 Picture PSM Dynamic Contrast Brightness Colour Sharpness CSM XD Advanced Reset 9 Sound SSM AVL Balance Flat Off Off 0 50 50 Speaker 10 Time Clock Off time On time Auto sleep 11 Special Language Child Lock Set ID XD Demo 12 Screen Auto config. Manual config. XGA/VGA mode ARC PFP Transparency Reset Variable by each mode On --:-Off Off Off English Off 1 To start Area management User control None Dynamic 100 50 50 50 Normal Auto Item Off 30 TV Pr 01 Off 16 : 9 Condition Remark
- 14 -
SVC REMOCON
NO
1 2 3 4 5 6 7 8 9 10 11
KEY
POWER
FUNTION
REAMARK
12
13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38
To turn the TV on or off To turn the TV on automatically if the power is supplied to the TV. (Use the POWER ON POWER key to deactivate): It should be deactivated when delivered. To activate the mute function. MUTE To check TV screen image easily. P-CHECK To check TV screen sound easily S-CHECK To select size of the main screen (Normal, Spectacle, Wide or Zoom) ARC Switch to closed caption broadcasting CAPTION To toggle on/off the teletext mode TXT To select an external input for the TV screen TV/AV To start turbo sound TURBO SOUND TURBO PICTURE To start turbo picture To enter adjustment mode when manufacturing the TV sets. To adjust the screen voltage (automatic): In-start mute Adjust AV(Enter into W/B adjustment mode) IN-START W/B adjustment (automatic): After adjusting the screen W/B adjustment Exit two times (Adjustment completed) To enter into the adjustment mode. To adjust horizontal line and sub-brightness. ADJ To select the multiple sound mode (Mono, Stereo or Foreign language) MPX To release the adjustment mode EXIT To easily adjust the screen according to surrounding brightness APC(PSM) To easily adjust sound according to the program type ASC(SSM) To check component input MULTIMIDIA To check the front AV FRONT-AV To move channel up/down or to select a function displayed on the screen. CH To adjust the volume or accurately control a specific function. VOL To set a specific function or complete setting. ENTER To move the channel down in the PIP screen. PIP CH-(OP1) To use as a red key in the teletext mode To move the channel in the PIP screen PIP CH+(OP2) To use as a green key in the teletext mode To switch between the main and sub screens PIP SWAP(OP3) To use as a yellow key in the teletext mode To select the input status in the PIP screen PIP INPUT(OP4) To use as a blue key in the teletext mode To set a function that will automatically adjust screen status to match EYE the surrounding brightness so natural color can be displayed. To select the functions such as video, voice, function or channel. MENU To set the delivery condition status after manufacturing the TV set. IN-STOP To halt the main screen in the normal mode, or the sub screen at the PIP screen. STILL Used as a hold key in the teletext mode (Page updating is stopped.) Displays the teletext time in the normal mode TIME Enables to select the sub code in the teletext mode Used as the size key in the PIP screen in the normal mode SIZE Used as the size key in the teletext mode Used as the index key in the teletext mode (Top index will be MULTI PIP displayed if it is the top text.) To select the position of the PIP screen in the normal mode Used as the update key in the teletext mode (Text will be POSITION displayed if the current page is updated.) Used as Mode in the teletext mode MODE To select the simultaneous screen PIP To adjust screen tilt TILT To manually select the channel. 0~9
Shortcut keys Shortcut keys Shortcut keys
Use the AV key to enter the screen W/B adjustment mode.
Shortcut keys Shortcut keys
Shortcut keys
- 15 -
TROUBLESHOOTING
1. No power
Start check
No
Doesn't the screen whole come out? Yes Yes 1. Check the Power off condition 2. Check the Interface signal condition No No Is the Interface signal operated?
It is identical with power off condition?
No
Doesn't the low pressure output come out? Yes Yes 3. Check the St_by 5V signal circuit 4. Check the 5V Monitor signal circuit Yes Doesn't the St-by 5V signal come out? No No Yes
Doesn't the 5V monitor signal come out?
Doesn't the VSC signal RL_ON come out?
No
Doesn't the VSC Low pressure output come out? Yes 6. Check the VSC low pressure output
- 16 Yes No Yes 8. Check the Vs, Va voltage output circuit Yes 7. Check the VSC Vs_ON signal Doesn't the VSC signal Vs-ON come out? Doesn't the Vs,Va voltage output come out? Yes When remove the Y,Z B/D Module Input connector, Power Board high tension output voltage drop it occurs? No Yes 9. Check the power board output high tension circuit When remove the Y B/D Module Input connector, output voltage drop is occurs? Yes 10. Check the Z B/D Module output circuit No
No
5. Check the VSC RL_ON signal
Doesn't the high tension output come out?
No
High tension output Voltage drop it occurs?
When remove the Z B/D Module Input connector, output voltage drop is occurs? Yes 11. Check the Y B/D Module output circuit
No
Manufacture enterprise meaning of a passage
2. VSC Board
2-1. No Power
(1) Symptom 1) Minute discharge doesn't occur at module. 2) Front LED doesn't come into action
(2). Check follow
Is the Power Cord plug in ? Plug in Power Cord No Yes
Is the Line Filter and PSU connected? Connect Cable (SC101) No
- 17 Yes No Replace Fuse Yes Connect Cable No Yes
Is the Fuse(F101) of PSU is normal?
Is it connect that PSU and 13Pin cable in VSC board?
After remove the cable connect to Power Board(except the CN101 connection cable), authorizes the AC voltage marking on manual. When ST-BY 5V does not operate, replace Power Board.
2-2. No Raster - LCD
(1) Symptom 1) Does't minute discharge at module. 2) It maintains the condition where the front LED is normal.
(2) Check follow
Is the Inverter On or Off Off No No Yes Yes
Is the inverter 24V on power board normal
'Inverter_On' Signal is High of 5th pin in P1000 on Main board
Check the Power board.
On 1. Check the Inverter connector 2. Check the LCD Module 1. Check the Main board
- 18 1. Reconnect the link cable in P804 No No Is output the normality Low/High voltage except stand-by 5V? No Yes 1. Change the Power Board 1. Check the Main Board. No Is the P804's output normal? 1. Change the Main Board No
Is the link cable normal?
Yes
Is the Power Board normal?
Yes
Is the VSC Board normal?
2-3. In case of occur strange screen into specific mode
2-3-1. In case of doesn't display the OSD (1) Symptom 1) LED is White 2) The minute discharge work continuously
(2) Check follow
Is the LVDS cable normal? No No Cable inserts well. Yes Replace cable.
Is the LVDS cable connected well?
Yes
Is the VSC Board normal? No No Replace FIL8668 IC(IC800). Yes Replace VSC B/D
IC800' operation is normal?
- 19 Is the Ctrl Board of Module normal? No Is the LCD Module normal? No Replace LCD Module
Yes
Plasma
Replace Ctrl Board in Plasma panel
LCD TV
2-3-2. In the case of doesn't work normally at specific input mode (1) Symptom 1) The screen doesn't work normally at specific input mode (RF, AV, Component, RGB, HDMI)
(2) Check follow 1) Check the all input model if all input display normally. 2) Check the PIP and Double Window if it display normally.(Re-Check it Swap)
(3) In case of unusual situation from RF mode
Is the Tuner normal? No No No Replace Tuner No Cable inserts well.
Is the Tuner Cable connected well?
Is normal the Input voltage, IIC Communication and CVBS output?
Yes
Is the IC300 normal? No No Replace IC300
Is the Input voltage, IIC Communication and HV sync normal?
- 20 No No Is the Input voltage, IIC Communication and HV sync normal? Replace IC800
Yes
Is the IC800 normal?
(4) When set doesn't display normally at RF , AV mode
Is the IC300 normal? No No Replace IC300
Is the Input voltage, IIC Communication and HV sync normal?
Yes
Is the IC800 normal? No No Replace IC800
Is the Input voltage, IIC Communication and HV sync normal?
(5) When set doesn't display nromally at Component, RGB mode
Is the IC800 normal? No No Replace IC800
Is the Input voltage, IIC Communication and HV sync normal?
(6) In the case of becomes unusual display from HDMI mode
- 21 No No Is the Input voltage, IIC Communication and HV sync normal? Replace IC1200 No No Is the Input voltage, IIC Communication and HV sync normal? Replace IC800
Is the IC1200 normal?
Yes
Is the IC800 normal?
2-4. In case of no sound
(1) Symptom 1) LED is White 2) Screen existent, but Sound isn't
(2) Check follow
All input(mode) is no sound? No Yes No Check the speaker cable No Yes No Set on speaker in menu Is the Speaker on in Menu? Is the speaker cable normal? IC400 operate normally? Yes
Replace IC400
Yes
- 22 No Download the EDID data No Yes No Check the signal after IC300 refer to circuit diagram. Is the output 52nd&53rd of IC300 normal? Replace IC300 No Check the Tuner In/Out
Only HDMI is no sound?
IC401 operate normally? No Replace IC401
Yes
IC402 operate normally? No Replace IC402
Yes
Replace VSC B/D
Yes
Only AV input is no sound?
Yes
Only RF is no sound?
BLOCK DIAGRAM
- 23 -
EXPLODED VIEW (37LC2R)
030 111 020 140 110 130 150 070 160 120
010
- 24 -
050
040 090 080 100
060
EXPLODED VIEW PARTS LIST(37LC2R)
No. 010 PART NO. 30919E0046J 30919E0046H 020 030 6304FAU023A 3809900164F 3809900164E 040 3043900032B 3043900032E 3043900032C 050 060 070 080 090 100 110 68719ST997B 6400WMCX03A 4814V00520B 68719ST105A 49509K0222A 35509K0217A 49509K0341C 49509K0340D 49509K0341E 111 49509K0340C 49509K0341D 49509K0340E 120 4950TKA361M 4950TKA361L 130 140 150 68719STA69A 6709900016D 33139L3049A 33139L3022B 160 4950TKA362N 4950TKA362M DESCRIPTION Cover Assembly, 37LC2R-ZH BRAND 30909E0027 FOR EU(C/SKD) Cover Assembly, 37LC2R-ZH BRAND 30909E0027 FOR EU LCD,Panel-TFT, T370XW01-V1 37INCH 1366X768 500CD COLOR 72% T370XW01-V1 500NITS 8MS 20LAMPS Cover Assembly, 37LC2R-ZH NON H3-H(C/SKD) Cover Assembly, 37LC2R-ZH NON H3-H-atsula Base Assembly, 37LC2D-UD 35509K0214 FOR WORLDWIDE, BODY ASSY(C/SKD) Base Assembly, 37LC2D-EC 35509K0214 FOR NON USA, BASE ASSY(C/SKD) Base Assembly, 37LC2D-ND 35509K0214 FOR KOREA PCB Assembly,Sub, SUB T.T LP62A 37LC2R-ZH ALEULFX LOCAL KEY Speaker,Woofer, G1560102 ND35 15W 8OHM 82DB 100HZ 193X57mM LUG Plate, PRESS SPTE T0.5 PLATE RT-42PX40 SHIELD TUNER BOTTOM AP03NC SUS PRESS PCB Assembly,Sub, SUB T.T LP62A 37LC2R-ZH ALEULFX PREAMP + LED LC Plate, PRESS SBHG T2.0 SUPPORT STAND 37LC2 Cover, MOLD HIPS 37LC2 STAND MID INNER Plate, PRESS EGI 1.6 SUPPORTER SPC AUO SIDE FRAME (RIGHT, C/SKD) Plate, PRESS EGI 1.6 SUPPORTER SPC 37LC2R(AUO) Plate, PRESS EGI 1.6 SUPPORTER SPC AUO-SKD, For Thailand, Vietnam Plate, PRESS EGI 1.6 SUPPORTER SPC SIDE FRAME(AUO, LEFT, C/SKD) Plate, PRESS EGI 1.6 SUPPORTER SPC 37LC2R(AUO),LEFT Plate, PRESS EGI 1.6 SUPPORTER SPC SIDE FRAME(AUO, LEFT, C/SKD)-For Thailand, Vietnam Plate, FRAME, MAIN 37LC2R(C/SKD) Plate, FRAME, MAIN 37LC2R-atsula PCB Assembly,Sub, SUB T.T LP62C 37LC2R-TH AURDLFX SIDE A/V 37LC TH SMPS,AC/DC, LGLP2637HEP 90.0VTO264.0V 215W 47TO63HZ UL/CSA/SEMKO YY / AT / HE Main Total Assembly, 37LC2R-TH BRAND LP62A-C/SKD Main Total Assembly, 32LC2R-TH AUO BRAND LP62A Plate, SHIELD, MAIN PLUS ANALOG AV(37LC2R-TH),C/SKD Plate, SHIELD, MAIN PLUS ANALOG AV(37LC2R-TH)
- 25 -
EXPLODED VIEW(42LC2R)
- 26 -
EXPLODED VIEW PARTS LIST(42LC2R)
No. 010 020 PART NO. 30919E0047H 6304FLP363A or 6304FLP353A 030 040 050 3809900165L 3043900034C 68719ST997B 68719ST997C 060 061 070 6400WMCX03A 6400DTTX02A 68719ST105A 68719ST105C 080 090 100 110 120 35519K0030D 49519S0036F 31419SNJ81A 6709900017B 33139L3050A 33139L3050C 130 68719STA68A 68719STA68C 140 49509K0173H DESCRIPTION Cover Assembly, 42LC2R BRAND 30909E0028 ZH C/SKD LCD,Panel-TFT, LC420W02-SLA1 42INCH 1365X768 500CD COLOR 72% LCD,Panel-TFT, LC420W02-B6K2 42INCH 1365X768 500CD COLOR 72% Cover Assembly, 42LC2R HURRICANE 42" SPRAY Base Assembly, 42LC2 42LC2 FOR USA C/SKD PCB Assembly,Sub, SUB T.T LP62A 37LC2R-ZH ALEULFX LOCAL KEY PCB Assembly, SUB T.T LP62A 37LC2R-ZH ALEULFX LOCAL KEY NT CKD Speaker,Woofer, G1560102 ND35 15W 8OHM 82DB 100HZ 193X57mM LUG Speaker,Tweeter, EN15D-6629 TOPTONE TWEETER(DOME) 8OHM 15/20W 78DB OTHERS LC2 MODEL PCB Assembly,Sub, SUB T.T LP62A 37LC2R-ZH ALEULFX PREAMP + LED LC PCB Assembly, SUB T.T LP62A 37LC2R-ZH ALEULFX PREAMP + LED LC NT CKD Cover Assembly, 42LC2 STAND 35509K0220B SUPPORT C/SKD Plate Assembly, FRAME MAIN 42LC2R-ZH C/SKD Chassis Assembly, SUB LA51D AC INLET ASSY SMPS,AC/DC, YP4201 90.0VTO264.0V 280W 47TO63HZ UL/CSA/TUV/SEMKO 42" LCD Main Total Assembly, 42LC2R-TH BRAND LP62A Main Total Assembly, 42LC2R-TH BRAND LP62A NT CKD PCB Assembly,Sub, SUB T.T LP62C 42LC2R-TH AURDLFX SIDE A/V FOR 42LC TH PCB Assembly, SUB T.T LP62C 42LC2R-TH AURDLFX SIDE A/V FOR 42LC TH NT CKD Plate SHIELD MAIN ANALOG 42LC2R-TH C/SKD
- 27 -
REPLACEMENT PARTS LIST
For Capacitor & Resistors, the charactors at 2nd and 3rd digit in the P/No. means as follows; CC, CX, CK, CN, CH : Ceramic CQ : Polyestor CE : Electrolytic CF : Fixed Film RD : Carbon Film RS : Metal Oxide Film RN : Metal Film RH : CHIP, Metal Glazed(Chip) RR : Drawing
*S *AL LOC. NO.
PART NO.
DATE: 2006. 04. 05. DESCRIPTION / SPECIFICATION
*S *AL LOC. NO. C1157 C1158 C1207 C1222 C1226 C1244 C1403 C1460 C1468 C148 C149 C174 C175 C1814 C1826 C211 C213 C215 C224 C227 C238 C314 C316 C317 C318 C349 C351 C354 C401 C405 C409 C412 C432 C446 C451 C452 C463 C464 C466 C467 C512 C611 C834 C835 C836 C837 C838 C839 C840 C841 C842 C853 C855 C886
PART NO. 0CE476WF6DC 0CE476WF6DC 0CE476SF6DC 0CE106SH6DC 0CE106SH6DC 0CE106SH6DC 0CH8106J691 0CE106SH6DC 0CE106SH6DC 0CE227SF6DC 0CE227SF6DC 0CE106SH6DC 0CE106SH6DC 0CE226SF6DC 0CE476SF6DC 0CE477SF6DC 0CE477SF6DC 0CE106SH6DC 0CE477SF6DC 0CE107SF6DC 0CE227SF6DC 0CE107SF6DC 0CE226SF6DC 0CE107SF6DC 0CE476SF6DC 0CE476SF6DC 0CE105SK6DC 0CE105SK6DC 0CE476SF6DC 0CE107SF6DC 0CE226SF6DC 0CE335SK6DC 0CE106WFKDC 0CE335SK6DC 0CE106SH6DC 0CE106SH6DC 0CE475SK6DC 0CE475SK6DC 0CE475SK6DC 0CE475SK6DC 0CE476SF6DC 0CE107SF6DC 0CE106WFKDC 0CE226SF6DC 0CE106WFKDC 0CE226SF6DC 0CE226SF6DC 0CE106WFKDC 0CE106WFKDC 0CE226SF6DC 0CE106WFKDC 0CE226SF6DC 0CE226SF6DC 0CE106WFKDC
DATE: 2006. 04. 05. DESCRIPTION / SPECIFICATION MVK6.3TP16VC47M 47uF 20% 16 MVK6.3TP16VC47M 47uF 20% 16 VMV476M016S0ANC010 47uF 20% VMV106M025S0ANB010 10uF 20% VMV106M025S0ANB010 10uF 20% VMV106M025S0ANB010 10uF 20% MVK5.0TP35VC10M 10uF 20% 35 VMV106M025S0ANB010 10uF 20% VMV106M025S0ANB010 10uF 20% MVG6.3TP16VC220M 220uF 20% MVG6.3TP16VC220M 220uF 20% VMV106M025S0ANB010 10uF 20% VMV106M025S0ANB010 10uF 20% VMV226M016S0ANB010 22uF 20% VMV476M016S0ANC010 47uF 20% VMV477M016S0ANG030 470uF 20 VMV477M016S0ANG030 470uF 20 VMV106M025S0ANB010 10uF 20% VMV477M016S0ANG030 470uF 20 VMV107M016S0ANE010 100uF 20 MVG6.3TP16VC220M 220uF 20% VMV107M016S0ANE010 100uF 20 VMV226M016S0ANB010 22uF 20% VMV107M016S0ANE010 100uF 20 VMV476M016S0ANC010 47uF 20% VMV476M016S0ANC010 47uF 20% VMV105M050S0ANB010 1uF 20% VMV105M050S0ANB010 1uF 20% VMV476M016S0ANC010 47uF 20% VMV107M016S0ANE010 100uF 20 VMV226M016S0ANB010 22uF 20% VMV335M050S0ANB010 3.3uF 20 MVK4.0TP16VC10M 10uF 20% 16 VMV335M050S0ANB010 3.3uF 20 VMV106M025S0ANB010 10uF 20% VMV106M025S0ANB010 10uF 20% VMV475M050S0ANB010 4.7uF 20 VMV475M050S0ANB010 4.7uF 20 VMV475M050S0ANB010 4.7uF 20 VMV475M050S0ANB010 4.7uF 20 VMV476M016S0ANC010 47uF 20% VMV107M016S0ANE010 100uF 20 MVK4.0TP16VC10M 10uF 20% 16 VMV226M016S0ANB010 22uF 20% MVK4.0TP16VC10M 10uF 20% 16 VMV226M016S0ANB010 22uF 20% VMV226M016S0ANB010 22uF 20% MVK4.0TP16VC10M 10uF 20% 16 MVK4.0TP16VC10M 10uF 20% 16 VMV226M016S0ANB010 22uF 20% MVK4.0TP16VC10M 10uF 20% 16 VMV226M016S0ANB010 22uF 20% VMV226M016S0ANB010 22uF 20% MVK4.0TP16VC10M 10uF 20% 16
MAIN BOARD CAPACITOR
C1001 C1005 C1007 C1009 C1012 C1014 C1016 C1019 C1020 C1022 C1023 C1048 C1049 C1050 C1051 C1053 C1054 C1062 C1063 C1064 C1065 C1067 C1069 C1070 C1072 C1084 C1085 C1086 C1087 C1088 C1089 C1092 C1101 C1107 C1109 C1110 C1111 C1113 C1128 C1129 C1130 C1131 C1132 C1133 C1135 C1137 C1146 C1147 C1148 C1149 C1151 C1152 0CE477WF6DC 0CE477WF6DC 0CE476WF6DC 0CE477WF6DC 0CE476WF6DC 0CE477WF6DC 0CE107WF6DC 0CE477WF6DC 0CE107WF6DC 0CE107WF6DC 0CE477WF6DC 0CE107WF6DC 0CE107WF6DC 0CE107WF6DC 0CE107WF6DC 0CE476WF6DC 0CE476WF6DC 0CE476WF6DC 0CE476WF6DC 0CE476WF6DC 0CE476WF6DC 0CE477WF6DC 0CE477WF6DC 0CE107WF6DC 0CE476WF6DC 0CE476WF6DC 0CE476WF6DC 0CE476WF6DC 0CE476WF6DC 0CE476WF6DC 0CE476WF6DC 0CE476WF6DC 0CE477WF6DC 0CE477WF6DC 0CE477WF6DC 0CE227WF6DC 0CE477WF6DC 0CE227WF6DC 0CE477WF6DC 0CE107WF6DC 0CE107WF6DC 0CE107WF6DC 0CE107WF6DC 0CE107WF6DC 0CE476WF6DC 0CE476WF6DC 0CE476WF6DC 0CE107WF6DC 0CE107WF6DC 0CE107WF6DC 0CE107WF6DC 0CE107WF6DC MVK10TP16VC470M 470uF 20% 1 MVK10TP16VC470M 470uF 20% 1 MVK6.3TP16VC47M 47uF 20% 16 MVK10TP16VC470M 470uF 20% 1 MVK6.3TP16VC47M 47uF 20% 16 MVK10TP16VC470M 470uF 20% 1 MVK6.3TP16VC100M 100uF 20% MVK10TP16VC470M 470uF 20% 1 MVK6.3TP16VC100M 100uF 20% MVK6.3TP16VC100M 100uF 20% MVK10TP16VC470M 470uF 20% 1 MVK6.3TP16VC100M 100uF 20% MVK6.3TP16VC100M 100uF 20% MVK6.3TP16VC100M 100uF 20% MVK6.3TP16VC100M 100uF 20% MVK6.3TP16VC47M 47uF 20% 16 MVK6.3TP16VC47M 47uF 20% 16 MVK6.3TP16VC47M 47uF 20% 16 MVK6.3TP16VC47M 47uF 20% 16 MVK6.3TP16VC47M 47uF 20% 16 MVK6.3TP16VC47M 47uF 20% 16 MVK10TP16VC470M 470uF 20% 1 MVK10TP16VC470M 470uF 20% 1 MVK6.3TP16VC100M 100uF 20% MVK6.3TP16VC47M 47uF 20% 16 MVK6.3TP16VC47M 47uF 20% 16 MVK6.3TP16VC47M 47uF 20% 16 MVK6.3TP16VC47M 47uF 20% 16 MVK6.3TP16VC47M 47uF 20% 16 MVK6.3TP16VC47M 47uF 20% 16 MVK6.3TP16VC47M 47uF 20% 16 MVK6.3TP16VC47M 47uF 20% 16 MVK10TP16VC470M 470uF 20% 1 MVK10TP16VC470M 470uF 20% 1 MVK10TP16VC470M 470uF 20% 1 MVK8.0TP16VC220M 220uF 20% MVK10TP16VC470M 470uF 20% 1 MVK8.0TP16VC220M 220uF 20% MVK10TP16VC470M 470uF 20% 1 MVK6.3TP16VC100M 100uF 20% MVK6.3TP16VC100M 100uF 20% MVK6.3TP16VC100M 100uF 20% MVK6.3TP16VC100M 100uF 20% MVK6.3TP16VC100M 100uF 20% MVK6.3TP16VC47M 47uF 20% 16 MVK6.3TP16VC47M 47uF 20% 16 MVK6.3TP16VC47M 47uF 20% 16 MVK6.3TP16VC100M 100uF 20% MVK6.3TP16VC100M 100uF 20% MVK6.3TP16VC100M 100uF 20% MVK6.3TP16VC100M 100uF 20% MVK6.3TP16VC100M 100uF 20%
- 28 -
*S *AL LOC. NO. C898 C901 C904 C905 C930 C943 C950 C1813 C1031 C210 C237 C1108 C1112 C1428 C1446 C1003 C1026 C1029 C1033 C1034 C1036 C1037 C1041 C1071 C1117 C1118 C1126 C1127 C1223 C1224 C1225 C1228 C1405 C1419 C1420 C1421 C1422 C1455 C1456 C1457 C1458 C1459 C1474 C1811 C1851 C234 C312 C313 C319 C321 C322 C326 C327 C328 C329 C330 C331 C332 C333 C334 C335 C336
PART NO. 0CE106WFKDC 0CE226SF6DC 0CE226SF6DC 0CE226SF6DC 0CE226SF6DC 0CE226SF6DC 0CE226SF6DC 0CE106WFKDC 0CE476WK6DC 0CE477SF6DC 0CE227SF6DC 0CE477EK618 0CE477EK618 0CE477EK618 0CE477EK618 0CK474CH94A 0CK104CK56A 0CK104CK56A 0CK104CK56A 0CK103CK56A 0CK104CK56A 0CK104CK56A 0CK103CK56A 0CK104CK56A 0CK104CK56A 0CK104CK56A 0CK103CK56A 0CK103CK56A 0CC180CK41A 0CK103CK56A 0CC180CK41A 0CK103CK51A 0CK104CK56A 0CK333CK56A 0CK333CK56A 0CK333CK56A 0CK333CK56A 0CK104CK56A 0CK104CK56A 0CK105DF64A 0CK105DF64A 0CK102CK56A 0CC102CK41A 0CK104CK56A 0CK104CK56A 0CC271CK41A 0CK103CK56A 0CK103CK56A 0CK104CK56A 0CK104CK56A 0CK104CK56A 0CK225DFK4A 0CK474CH94A 0CK474CH94A 0CK225DFK4A 0CK474CH94A 0CK225DFK4A 0CK474CH94A 0CK474CH94A 0CK225DFK4A 0CK474CH94A 0CK225DFK4A
DATE: 2006. 04. 05. DESCRIPTION / SPECIFICATION MVK4.0TP16VC10M 10uF 20% 16 VMV226M016S0ANB010 22uF 20% VMV226M016S0ANB010 22uF 20% VMV226M016S0ANB010 22uF 20% VMV226M016S0ANB010 22uF 20% VMV226M016S0ANB010 22uF 20% VMV226M016S0ANB010 22uF 20% MVK4.0TP16VC10M 10uF 20% 16 MVK8.0TP50VC47M 47uF 20% 50 VMV477M016S0ANG030 470uF 20 MVG6.3TP16VC220M 220uF 20% KMG5.0TP50VB470M 470uF 20% KMG5.0TP50VB470M 470uF 20% KMG5.0TP50VB470M 470uF 20% KMG5.0TP50VB470M 470uF 20% 0603F474Z250CT 470nF -20TO+ 0603B104K500CT 100nF 10% 50 0603B104K500CT 100nF 10% 50 0603B104K500CT 100nF 10% 50 0603B103K500CT 10nF 10% 50V 0603B104K500CT 100nF 10% 50 0603B104K500CT 100nF 10% 50 0603B103K500CT 10nF 10% 50V 0603B104K500CT 100nF 10% 50 0603B104K500CT 100nF 10% 50 0603B104K500CT 100nF 10% 50 0603B103K500CT 10nF 10% 50V 0603B103K500CT 10nF 10% 50V C1608C0G1H180JT 18pF 5% 50V 0603B103K500CT 10nF 10% 50V C1608C0G1H180JT 18pF 5% 50V 0603B103K500CT 10nF 10% 50V 0603B104K500CT 100nF 10% 50 C1608X7R1H333KT 33nF 10% 50 C1608X7R1H333KT 33nF 10% 50 C1608X7R1H333KT 33nF 10% 50 C1608X7R1H333KT 33nF 10% 50 0603B104K500CT 100nF 10% 50 0603B104K500CT 100nF 10% 50 0805F105Z160CT 1uF -20TO+80 0805F105Z160CT 1uF -20TO+80 0603B102K500CT 1nF 10% 50V C1608C0G1H102JT 1nF 5% 50V 0603B104K500CT 100nF 10% 50 0603B104K500CT 100nF 10% 50 C1608C0G1H271JT 270pF 5% 50 0603B103K500CT 10nF 10% 50V 0603B103K500CT 10nF 10% 50V 0603B104K500CT 100nF 10% 50 0603B104K500CT 100nF 10% 50 0603B104K500CT 100nF 10% 50 C2012Y5V1C225MT 2.2uF 20% 1 0603F474Z250CT 470nF -20TO+ 0603F474Z250CT 470nF -20TO+ C2012Y5V1C225MT 2.2uF 20% 1 0603F474Z250CT 470nF -20TO+ C2012Y5V1C225MT 2.2uF 20% 1 0603F474Z250CT 470nF -20TO+ 0603F474Z250CT 470nF -20TO+ C2012Y5V1C225MT 2.2uF 20% 1 0603F474Z250CT 470nF -20TO+ C2012Y5V1C225MT 2.2uF 20% 1
*S *AL LOC. NO. C337 C338 C339 C340 C341 C342 C343 C344 C345 C346 C347 C355 C357 C402 C403 C411 C414 C416 C428 C429 C430 C431 C433 C435 C438 C439 C441 C442 C457 C458 C459 C462 C494 C511 C605 C606 C607 C610 C800 C803 C806 C812 C813 C814 C815 C817 C818 C819 C820 C822 C823 C824 C825 C827 C828 C829 C830 C831 C833 C845 C868 C870
PART NO. 0CK474CH94A 0CK474CH94A 0CK225DFK4A 0CK474CH94A 0CK474CH94A 0CK225DFK4A 0CK474CH94A 0CK474CH94A 0CK225DFK4A 0CK474CH94A 0CK225DFK4A 0CK821CK56A 0CK103CK56A 0CK103CK56A 0CK104CK56A 0CK104CK56A 0CC560CK41A 0CK103CK56A 0CK474CH94A 0CK474CH94A 0CK474CH94A 0CK474CH94A 0CK474CH94A 0CK474CH94A 0CK474CH94A 0CK474CH94A 0CK474CH94A 0CK474CH94A 0CK682CK51A 0CK682CK51A 0CK682CK51A 0CK682CK51A 0CK104CK56A 0CK104CK56A 0CK104CK56A 0CK104CK56A 0CK104CK56A 0CK104CK56A 0CK104CK56A 0CK104CK56A 0CK104CK56A 0CC300CK41A 0CC300CK41A 0CK104CK56A 0CK104CK56A 0CK104CK56A 0CK104CK56A 0CK104CK56A 0CK104CK56A 0CK104CK56A 0CK104CK56A 0CK104CK56A 0CK104CK56A 0CK104CK56A 0CK104CK56A 0CK104CK56A 0CK104CK56A 0CK104CK56A 0CK104CK56A 0CK104CK56A 0CK104CK56A 0CK103CK56A
DATE: 2006. 04. 05. DESCRIPTION / SPECIFICATION 0603F474Z250CT 470nF -20TO+ 0603F474Z250CT 470nF -20TO+ C2012Y5V1C225MT 2.2uF 20% 1 0603F474Z250CT 470nF -20TO+ 0603F474Z250CT 470nF -20TO+ C2012Y5V1C225MT 2.2uF 20% 1 0603F474Z250CT 470nF -20TO+ 0603F474Z250CT 470nF -20TO+ C2012Y5V1C225MT 2.2uF 20% 1 0603F474Z250CT 470nF -20TO+ C2012Y5V1C225MT 2.2uF 20% 1 C1608X7R1H821KT 820pF 10% 5 0603B103K500CT 10nF 10% 50V 0603B103K500CT 10nF 10% 50V 0603B104K500CT 100nF 10% 50 0603B104K500CT 100nF 10% 50 C1608C0G1H560JT 56pF 5% 50V 0603B103K500CT 10nF 10% 50V 0603F474Z250CT 470nF -20TO+ 0603F474Z250CT 470nF -20TO+ 0603F474Z250CT 470nF -20TO+ 0603F474Z250CT 470nF -20TO+ 0603F474Z250CT 470nF -20TO+ 0603F474Z250CT 470nF -20TO+ 0603F474Z250CT 470nF -20TO+ 0603F474Z250CT 470nF -20TO+ 0603F474Z250CT 470nF -20TO+ 0603F474Z250CT 470nF -20TO+ C1608Y5P1H682KT 6.8nF 10% 5 C1608Y5P1H682KT 6.8nF 10% 5 C1608Y5P1H682KT 6.8nF 10% 5 C1608Y5P1H682KT 6.8nF 10% 5 0603B104K500CT 100nF 10% 50 0603B104K500CT 100nF 10% 50 0603B104K500CT 100nF 10% 50 0603B104K500CT 100nF 10% 50 0603B104K500CT 100nF 10% 50 0603B104K500CT 100nF 10% 50 0603B104K500CT 100nF 10% 50 0603B104K500CT 100nF 10% 50 0603B104K500CT 100nF 10% 50 C1608C0G1H300JT 30pF 5% 50V C1608C0G1H300JT 30pF 5% 50V 0603B104K500CT 100nF 10% 50 0603B104K500CT 100nF 10% 50 0603B104K500CT 100nF 10% 50 0603B104K500CT 100nF 10% 50 0603B104K500CT 100nF 10% 50 0603B104K500CT 100nF 10% 50 0603B104K500CT 100nF 10% 50 0603B104K500CT 100nF 10% 50 0603B104K500CT 100nF 10% 50 0603B104K500CT 100nF 10% 50 0603B104K500CT 100nF 10% 50 0603B104K500CT 100nF 10% 50 0603B104K500CT 100nF 10% 50 0603B104K500CT 100nF 10% 50 0603B104K500CT 100nF 10% 50 0603B104K500CT 100nF 10% 50 0603B104K500CT 100nF 10% 50 0603B104K500CT 100nF 10% 50 0603B103K500CT 10nF 10% 50V
- 29 -
*S *AL LOC. NO. C874 C881 C1000 C1002 C1004 C1006 C1008 C1010 C1011 C1013 C1015 C1017 C1018 C1021 C1024 C1025 C1027 C1028 C1030 C1035 C1039 C1040 C1042 C1044 C1045 C1046 C1047 C1058 C1059 C1060 C1061 C1066 C1068 C1073 C1074 C1075 C1076 C1077 C1078 C1079 C1080 C1081 C1082 C1083 C1090 C1091 C1100 C1102 C1103 C1104 C1105 C1106 C1114 C1115 C1116 C1119 C1120 C1121 C1122 C1123 C1124 C1125
PART NO. 0CK103CK56A 0CK104CK56A 0CK474CH94A 0CK104CK56A 0CK103CK56A 0CK104CK56A 0CK104CK56A 0CK104CK56A 0CK103CK56A 0CK104CK56A 0CK104CK56A 0CK104CK56A 0CK104CK56A 0CK104CK56A 0CK104CK56A 0CK104CK56A 0CK104CK56A 0CK104CK56A 0CK104CK56A 0CK103CK56A 0CK103CK56A 0CK103CK56A 0CK103CK56A 0CK104CK56A 0CK104CK56A 0CK104CK56A 0CK104CK56A 0CK103CK56A 0CK103CK56A 0CK103CK56A 0CK103CK56A 0CK104CK56A 0CK104CK56A 0CK104CK56A 0CK104CK56A 0CK104CK56A 0CK104CK56A 0CK104CK56A 0CK103CK56A 0CK103CK56A 0CK103CK56A 0CK103CK56A 0CK103CK56A 0CK104CK56A 0CK104CK56A 0CK103CK56A 0CK104CK56A 0CK104CK56A 0CK104CK56A 0CK104CK56A 0CK104CK56A 0CK104CK56A 0CK104CK56A 0CK104CK56A 0CK104CK56A 0CK104CK56A 0CK104CK56A 0CK104CK56A 0CK104CK56A 0CK103CK56A 0CK103CK56A 0CK103CK56A
DATE: 2006. 04. 05. DESCRIPTION / SPECIFICATION 0603B103K500CT 10nF 10% 50V 0603B104K500CT 100nF 10% 50 0603F474Z250CT 470nF -20TO+ 0603B104K500CT 100nF 10% 50 0603B103K500CT 10nF 10% 50V 0603B104K500CT 100nF 10% 50 0603B104K500CT 100nF 10% 50 0603B104K500CT 100nF 10% 50 0603B103K500CT 10nF 10% 50V 0603B104K500CT 100nF 10% 50 0603B104K500CT 100nF 10% 50 0603B104K500CT 100nF 10% 50 0603B104K500CT 100nF 10% 50 0603B104K500CT 100nF 10% 50 0603B104K500CT 100nF 10% 50 0603B104K500CT 100nF 10% 50 0603B104K500CT 100nF 10% 50 0603B104K500CT 100nF 10% 50 0603B104K500CT 100nF 10% 50 0603B103K500CT 10nF 10% 50V 0603B103K500CT 10nF 10% 50V 0603B103K500CT 10nF 10% 50V 0603B103K500CT 10nF 10% 50V 0603B104K500CT 100nF 10% 50 0603B104K500CT 100nF 10% 50 0603B104K500CT 100nF 10% 50 0603B104K500CT 100nF 10% 50 0603B103K500CT 10nF 10% 50V 0603B103K500CT 10nF 10% 50V 0603B103K500CT 10nF 10% 50V 0603B103K500CT 10nF 10% 50V 0603B104K500CT 100nF 10% 50 0603B104K500CT 100nF 10% 50 0603B104K500CT 100nF 10% 50 0603B104K500CT 100nF 10% 50 0603B104K500CT 100nF 10% 50 0603B104K500CT 100nF 10% 50 0603B104K500CT 100nF 10% 50 0603B103K500CT 10nF 10% 50V 0603B103K500CT 10nF 10% 50V 0603B103K500CT 10nF 10% 50V 0603B103K500CT 10nF 10% 50V 0603B103K500CT 10nF 10% 50V 0603B104K500CT 100nF 10% 50 0603B104K500CT 100nF 10% 50 0603B103K500CT 10nF 10% 50V 0603B104K500CT 100nF 10% 50 0603B104K500CT 100nF 10% 50 0603B104K500CT 100nF 10% 50 0603B104K500CT 100nF 10% 50 0603B104K500CT 100nF 10% 50 0603B104K500CT 100nF 10% 50 0603B104K500CT 100nF 10% 50 0603B104K500CT 100nF 10% 50 0603B104K500CT 100nF 10% 50 0603B104K500CT 100nF 10% 50 0603B104K500CT 100nF 10% 50 0603B104K500CT 100nF 10% 50 0603B104K500CT 100nF 10% 50 0603B103K500CT 10nF 10% 50V 0603B103K500CT 10nF 10% 50V 0603B103K500CT 10nF 10% 50V
*S *AL LOC. NO. C1134 C1136 C1138 C1139 C1140 C1141 C1142 C1143 C1144 C1145 C1150 C1153 C1154 C1155 C1156 C1205 C1212 C1213 C1214 C1215 C1216 C1217 C1218 C1219 C1220 C1221 C1227 C1229 C1230 C1231 C1235 C1236 C1237 C1238 C1239 C1240 C1241 C1242 C1243 C1247 C1248 C1251 C1252 C1313 C1401 C1406 C1410 C1411 C1412 C1413 C1418 C1423 C1435 C1436 C1437 C1438 C1439 C1441 C1447 C1448 C1449 C1450
PART NO. 0CK104CK56A 0CK104CK56A 0CK104CK56A 0CK103CK56A 0CK104CK56A 0CK104CK56A 0CK104CK56A 0CK103CK56A 0CK103CK56A 0CK103CK56A 0CK104CK56A 0CK104CK56A 0CK104CK56A 0CK103CK56A 0CK103CK56A 0CK104CK56A 0CK104CK56A 0CK104CK56A 0CK104CK56A 0CK104CK56A 0CK102CK56A 0CK102CK56A 0CK102CK56A 0CK102CK56A 0CK102CK56A 0CK102CK56A 0CK104CK56A 0CK104CK56A 0CK104CK56A 0CK104CK56A 0CK102CK56A 0CK102CK56A 0CK102CK56A 0CK102CK56A 0CK102CK56A 0CK102CK56A 0CK102CK56A 0CK102CK56A 0CK102CK56A 0CK104CK56A 0CK104CK56A 0CC101CK41A 0CC101CK41A 0CK104CK56A 0CK104CK56A 0CK104CK56A 0CK104CK56A 0CK104CK56A 0CK104CK56A 0CK104CK56A 0CK103CK56A 0CK104CK56A 0CK104CK56A 0CK104CK56A 0CK104CK56A 0CK104CK56A 0CK103CK56A 0CK104CK56A 0CK103CK56A 0CK103CK56A 0CK103CK56A 0CK103CK56A
DATE: 2006. 04. 05. DESCRIPTION / SPECIFICATION 0603B104K500CT 100nF 10% 50 0603B104K500CT 100nF 10% 50 0603B104K500CT 100nF 10% 50 0603B103K500CT 10nF 10% 50V 0603B104K500CT 100nF 10% 50 0603B104K500CT 100nF 10% 50 0603B104K500CT 100nF 10% 50 0603B103K500CT 10nF 10% 50V 0603B103K500CT 10nF 10% 50V 0603B103K500CT 10nF 10% 50V 0603B104K500CT 100nF 10% 50 0603B104K500CT 100nF 10% 50 0603B104K500CT 100nF 10% 50 0603B103K500CT 10nF 10% 50V 0603B103K500CT 10nF 10% 50V 0603B104K500CT 100nF 10% 50 0603B104K500CT 100nF 10% 50 0603B104K500CT 100nF 10% 50 0603B104K500CT 100nF 10% 50 0603B104K500CT 100nF 10% 50 0603B102K500CT 1nF 10% 50V 0603B102K500CT 1nF 10% 50V 0603B102K500CT 1nF 10% 50V 0603B102K500CT 1nF 10% 50V 0603B102K500CT 1nF 10% 50V 0603B102K500CT 1nF 10% 50V 0603B104K500CT 100nF 10% 50 0603B104K500CT 100nF 10% 50 0603B104K500CT 100nF 10% 50 0603B104K500CT 100nF 10% 50 0603B102K500CT 1nF 10% 50V 0603B102K500CT 1nF 10% 50V 0603B102K500CT 1nF 10% 50V 0603B102K500CT 1nF 10% 50V 0603B102K500CT 1nF 10% 50V 0603B102K500CT 1nF 10% 50V 0603B102K500CT 1nF 10% 50V 0603B102K500CT 1nF 10% 50V 0603B102K500CT 1nF 10% 50V 0603B104K500CT 100nF 10% 50 0603B104K500CT 100nF 10% 50 C1608C0G1H101JT 100pF 5% 50 C1608C0G1H101JT 100pF 5% 50 0603B104K500CT 100nF 10% 50 0603B104K500CT 100nF 10% 50 0603B104K500CT 100nF 10% 50 0603B104K500CT 100nF 10% 50 0603B104K500CT 100nF 10% 50 0603B104K500CT 100nF 10% 50 0603B104K500CT 100nF 10% 50 0603B103K500CT 10nF 10% 50V 0603B104K500CT 100nF 10% 50 0603B104K500CT 100nF 10% 50 0603B104K500CT 100nF 10% 50 0603B104K500CT 100nF 10% 50 0603B104K500CT 100nF 10% 50 0603B103K500CT 10nF 10% 50V 0603B104K500CT 100nF 10% 50 0603B103K500CT 10nF 10% 50V 0603B103K500CT 10nF 10% 50V 0603B103K500CT 10nF 10% 50V 0603B103K500CT 10nF 10% 50V
- 30 -
*S *AL LOC. NO. C1461 C1466 C1467 C1469 C147 C1470 C1473 C1475 C1476 C150 C151 C152 C178 C1800 C1801 C1802 C1803 C1804 C1805 C1806 C1807 C1808 C1809 C1810 C1812 C1815 C1852 C218 C219 C220 C221 C222 C223 C225 C226 C229 C231 C233 C315 C320 C348 C350 C352 C353 C356 C406 C407 C408 C415 C434 C436 C437 C444 C445 C469 C479 C483 C493 C495 C502 C503 C506
PART NO. 0CK104CK56A 0CK104CK56A 0CC101CK41A 0CK104CK56A 0CK102CK56A 0CC102CK41A 0CK104CK56A 0CK104CK56A 0CK104CK56A 0CK102CK56A 0CK103CK56A 0CK103CK56A 0CK104CK56A 0CK104CK56A 0CK104CK56A 0CK104CK56A 0CK103CK56A 0CK104CK56A 0CK104CK56A 0CK104CK56A 0CK104CK56A 0CK104CK56A 0CK104CK56A 0CK104CK56A 0CK104CK56A 0CK104CK56A 0CK104CK56A 0CK103CK56A 0CC680CK41A 0CC680CK41A 0CK103CK56A 0CK103CK56A 0CC101CK41A 0CK273CK56A 0CK103CK56A 0CK104CK56A 0CK273CK56A 0CC271CK41A 0CK103CK56A 0CK103CK56A 0CK104CK56A 0CC102CK41A 0CK563CK56A 0CK223CK56A 0CK104CK56A 0CK104CK56A 0CH5010K116 0CH5010K116 0CC560CK41A 0CK104CK56A 0CK103CK56A 0CC101CK41A 0CK103CK56A 0CK471CK56A 0CK104CK56A 0CK471CK56A 0CK471CK56A 0CK102CK56A 0CK102CK56A 0CK103CK56A 0CK103CK56A 0CC120CK41A
DATE: 2006. 04. 05. DESCRIPTION / SPECIFICATION 0603B104K500CT 100nF 10% 50 0603B104K500CT 100nF 10% 50 C1608C0G1H101JT 100pF 5% 50 0603B104K500CT 100nF 10% 50 0603B102K500CT 1nF 10% 50V C1608C0G1H102JT 1nF 5% 50V 0603B104K500CT 100nF 10% 50 0603B104K500CT 100nF 10% 50 0603B104K500CT 100nF 10% 50 0603B102K500CT 1nF 10% 50V 0603B103K500CT 10nF 10% 50V 0603B103K500CT 10nF 10% 50V 0603B104K500CT 100nF 10% 50 0603B104K500CT 100nF 10% 50 0603B104K500CT 100nF 10% 50 0603B104K500CT 100nF 10% 50 0603B103K500CT 10nF 10% 50V 0603B104K500CT 100nF 10% 50 0603B104K500CT 100nF 10% 50 0603B104K500CT 100nF 10% 50 0603B104K500CT 100nF 10% 50 0603B104K500CT 100nF 10% 50 0603B104K500CT 100nF 10% 50 0603B104K500CT 100nF 10% 50 0603B104K500CT 100nF 10% 50 0603B104K500CT 100nF 10% 50 0603B104K500CT 100nF 10% 50 0603B103K500CT 10nF 10% 50V C1608C0G1H680JT 68pF 5% 50V C1608C0G1H680JT 68pF 5% 50V 0603B103K500CT 10nF 10% 50V 0603B103K500CT 10nF 10% 50V C1608C0G1H101JT 100pF 5% 50 0603B273K500CT 27nF 10% 50V 0603B103K500CT 10nF 10% 50V 0603B104K500CT 100nF 10% 50 0603B273K500CT 27nF 10% 50V C1608C0G1H271JT 270pF 5% 50 0603B103K500CT 10nF 10% 50V 0603B103K500CT 10nF 10% 50V 0603B104K500CT 100nF 10% 50 C1608C0G1H102JT 1nF 5% 50V C1608X7R1H563KT 56nF 10% 50 UMK107JB223KA-T 22nF 10% 50 0603B104K500CT 100nF 10% 50 0603B104K500CT 100nF 10% 50 0805N1R0D500LT 1pF 0.5PF 50 0805N1R0D500LT 1pF 0.5PF 50 C1608C0G1H560JT 56pF 5% 50V 060