Text preview for : Tda4852.pdf part of Philips TDA4852 Philips Quality Data Sheet
Back to : Tda4852.pdf | Home
INTEGRATED CIRCUITS
DATA SHEET
TDA4852 Horizontal and vertical deflection controller for autosync monitors
Preliminary specification File under Integrated Circuits, IC02 December 1992
Philips Semiconductors
Preliminary specification
Horizontal and vertical deflection controller for autosync monitors
FEATURES · Low jitter · All adjustments DC-controllable · Alignment-free oscillators · Sync separators for video or horizontal and vertical TTL sync levels regardless of polarity · Horizontal oscillator with PLL1 for sync and PLL2 for flyback · Constant vertical and E/W amplitude in autosync operation · DC-coupling to vertical power amplifier · Internal supply voltage stabilization with excellent ripple rejection to ensure stable geometrical adjustments GENERAL DESCRIPTION
TDA4852
The TDA4852 is a monolithic integrated circuit for economical solutions in autosync monitors. The IC incorporates the complete horizontal and vertical small signal processing. In conjunction with TDA4860/61/65, or TDA8351 (vertical output circuits) the ICs offer an extremely advanced system solution.
QUICK REFERENCE DATA SYMBOL VP IP Vi sync supply current AC-coupled composite video signal with negative-going sync (peak-to-peak value, pin 9) sync slicing level DC-coupled TTL-compatible horizontal sync signal (peak-to-peak value, pin 9) slicing level DC-coupled TTL-compatible vertical sync signal (peak-to-peak value, pin 10) slicing level Io V Io H Tamb vertical differential output current (peak-to-peak value, pins 5 and 6) horizontal sink output current on pin 3 operating ambient temperature range PARAMETER positive supply voltage (pin 1) MIN. 9.2 - - - 1.7 1.2 1.7 1.2 - - 0 TYP. 12 40 1 120 - 1.4 - 1.4 1 - - MAX. 16 - - - - 1.6 - 1.6 - 60 +70 UNIT V mA V mV V V V V mA mA °C
ORDERING INFORMATION PACKAGE EXTENDED TYPE NUMBER TDA4852 Note 1. SOT146-1; 1996 November 27. PINS 20 PIN POSITION DIL MATERIAL plastic CODE SOT146(1)
December 1992
2
Philips Semiconductors
Preliminary specification
Horizontal and vertical deflection controller for autosync monitors
TDA4852
December 1992
3
Fig.1 Block diagram.
Philips Semiconductors
Preliminary specification
Horizontal and vertical deflection controller for autosync monitors
PINNING SYMBOL VP FLB HOR GND VERT1 VERT2 n.c. CLBL HVS VS EW CVA RVA REW RVOS CVOS PLL1 RHOS CHOS PLL2 PIN 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 DESCRIPTION positive supply voltage horizontal flyback input horizontal output ground (0 V) vertical output 1; negative-going sawtooth vertical output 2; positive-going sawtooth not connected clamping/blanking pulse output horizontal sync/video input vertical sync input E/W output (parabola to driver stage) capacitor for amplitude control vertical amplitude adjustment input E/W amplitude adjustment input (parabola) vertical oscillator resistor vertical oscillator capacitor PLL1 phase horizontal oscillator resistor horizontal oscillator capacitor PLL2 phase
TDA4852
Fig.2 Pin configuration.
December 1992
4
Philips Semiconductors
Preliminary specification
Horizontal and vertical deflection controller for autosync monitors
FUNCTIONAL DESCRIPTION Horizontal sync separator and polarity correction An AC-coupled video signal or a DC-coupled TTL sync signal (H only or composite sync) is input on pin 9. Video signals are clamped with top sync on 1.28 V, and are sliced at 1.4 V. This results in a fixed absolute slicing level of 120 mV related to top sync. DC-coupled TTL sync signals are also sliced at 1.4 V, however with the clamping circuit in current limitation. The polarity of the separated sync is detected by internal integration of the signal, then the polarity is corrected. The corrected sync is input signal for the vertical sync integrator and the PLL1 stage. Vertical sync separator, polarity correction and vertical sync integrator DC-coupled vertical TTL sync signals may be applied to pin 10. They are sliced at 1.4 V. The polarity of the separated sync is detected by internal integration, then the polarity is corrected. If pin 10 is not used, it must be connected to ground. The separated Vi sync signal from pin 10, or the integrated composite sync signal from pin 9 (TTL or video) triggers directly the vertical oscillator. Clamping and V-blanking generator A combined clamping and V-blanking pulse is available on pin 8 (suitable for the video pre-amplifier TDA4881). The lower level of 1.9 V is the blanking signal derived from the vertical blanking pulse from the internal vertical oscillator. Vertical blanking starts with vertical sync and stops at the begin of vertical scan. By this, an optimum blanking is achieved. The upper level of 5.4 V is the horizontal clamping pulse with an internally fixed pulse width of 0.8 µs. December 1992 A monoflop, which is triggered by the trailing edge of the horizontal sync pulse, generates this pulse. If composite sync is applied, one clamping pulse per H-period is generated during V-sync. The phase of the clamping pulse may change during V-sync (see Fig.8). PLL1 phase detector The phase detector is a standard type using switched current sources. The middle of the sync is compared with a fixed point of the oscillator sawtooth voltage. The PLL filter is connected to pin 17. If composite sync is applied, the disturbed control voltage is corrected during V-sync (see Fig.8). Horizontal oscillator This oscillator is of the relaxation type and requires a fixed capacitor of 10 nF at pin 19. By changing the current into pin 18 the whole frequency range from 13 to 100 kHz can be covered. The current can be generated either by a frequency to voltage converter or by a resistor. A frequency adjustment may also be added if necessary. The PLL1 control voltage at pin 17 modulates via a buffer stage the oscillator thresholds. A high DC-loop gain ensures a stable phase relationship between horizontal sync and line flyback pulses. PLL2 phase detector This phase detector is similar to the PLL1 phase detector. Line flyback signals (pin 2) are compared with a fixed point of the oscillator sawtooth voltage. Delays in the horizontal deflection circuit are compensated by adjusting the phase relationship between horizontal sync and horizontal output pulses. A certain amount of phase adjustment is possible by injecting a DC current from an external source into the PLL2 filter capacitor at pin 20. 5 Horizontal driver
TDA4852
This open-collector output stage (pin 3) can directly drive an external driver transistor. The saturation voltage is less than 300 mV at 20 mA. To protect the line deflection transistor, the horizontal output stage does not conduct for VP < 6.4 V (pin 1). Vertical oscillator and amplitude control This stage is designed for fast stabilization of the vertical amplitude after changes in sync conditions. The free-running frequency f0 is determined by the values of RVOS and CVOS. The recommended values should be altered marginally only to preserve the excellent linearity and noise performance. The vertical drive currents I5 and I6 are in relation to the value of RVOS. Therefore, the oscillator frequency must be determined only by CVOS on pin 16. 1 f 0 = ----------------------------------------------------10.8 × R VOS × C VOS To achieve a stabilized amplitude the free-running frequency f0 (without adjustment) must be lower than the lowest occurring sync frequency. The following contributions can be assumed:
minimum frequency offset between f0 and the lowest trigger frequency spread of IC spread of R (22 k) spread of C (0.1 µF) 10% ±3% ±1% ±5% 19% 50 Result: f 0 = ---------- Hz = 42 Hz 1.19 (for 50 to 110 Hz application)
Philips Semiconductors
Preliminary specification
Horizontal and vertical deflection controller for autosync monitors
LIMITING VALUES In accordance with the Absolute Maximum Rating System (IEC 134) SYMBOL VP V3 V8 Vn I2 I3 I8 Tstg Tamb Tj VESD supply voltage (pin 1) voltage on pin 3 voltage on pin 8 voltage on pins 5, 6, 9, 10, 13, 14 and 18 current on pin 2 current on pin 3 current on pin 8 storage temperature range operating ambient temperature range maximum junction temperature electrostatic handling for all pins (note 1) PARAMETER MIN. -0.5 -0.5 -0.5 -0.5 - - - -55 0 0 -
TDA4852
MAX. 16 16 7 6.5 ±10 100 -10 +50 70 +150 ±400 V V V V
UNIT
mA mA mA °C °C °C V
Note to the Limiting Values 1. Equivalent to discharging a 200 pF capacitor through a 0 series resistor. THERMAL RESISTANCE SYMBOL Rth j-a PARAMETER from junction to ambient in free air THERMAL RESISTANCE 65 K/W
December 1992
6
Philips Semiconductors
Preliminary specification
Horizontal and vertical deflection controller for autosync monitors
CHARACTERISTICS VP = 12 V; Tamb =+25 °C; measurements taken in Fig.3 unless otherwise specified. SYMBOL VP IP PARAMETER positive supply voltage (pin 1) supply current I18 = -1.05 mA I18 = -3.388 mA Internal reference voltage Vref TC PSRR VP internal reference voltage temperature coefficient power supply ripple rejection supply voltage (pin 1) to ensure all internal reference voltages V10 = 5 V sync on green - 1.1 RS = 50 Vi sync > 200 mV during sync V9 > 1.5 V fH = 31 kHz; I18 = -1.050 mA fH = 64 kHz; I18 = -2.169 mA fH = 100 kHz; I18 = -3.388 mA Horizontal sync input (DC-coupled, TTL-compatible) Vi sync sync input signal (peak-to-peak value, pin 9) slicing level tp tr, tf I9 minimum pulse width rise time and fall time input current V9 = 0.8 V V9 = 5.5 V Automatic horizontal polarity switch tp H/tH horizontal sync pulse width related to tH (duty factor for automatic polarity correction) delay time for changing sync polarity H-sync on pin 9 - - 1.7 1.2 700 10 - - - 1.4 - - - - 90 - - 1.3 7 3.5 2.5 300 1.28 120 - 80 2 10 5 3.4 Tamb = +20 to +100 °C f = 1 kHz sinewave f = 1 MHz sinewave 6.0 - 60 25 9.2 6.25 - 75 35 - CONDITIONS MIN. 9.2 - - 12 36 40 TYP.
TDA4852
MAX. 16 44 49
UNIT V mA mA
6.5 ±90 - - 16
V 10-6/K dB dB V
Composite sync input (AC-coupled) vi sync sync amplitude of video input signal (pin 9) top sync clamping level slicing level above top sync level RS r9 I9 tint allowed source resistance for 7% duty factor differential input resistance charging current of coupling capacitor vertical sync integration time to generate vertical trigger pulse
- 1.5 150 1.5 - 3 13 6.5 4.5
mV V mV k µA µs µs µs
- 1.6 - 500 -200 10
V V ns ns µA µA
30
%
tp
0.3
-
1.8
ms
December 1992
7
Philips Semiconductors
Preliminary specification
Horizontal and vertical deflection controller for autosync monitors
SYMBOL PARAMETER CONDITIONS V-sync on pin 10 1.7 1.2 0 < V10 < 5.5 V - - Fig.6 - internal V blanking H-sync on pin 9 H and V scanning 1.6 5.15 2.3 - V8 = 3 V Vref = 6.25 V R15 = 22 k; C16 = 0.1 µF no f0 adjustment R15 = 22 k measured on pin 8 - 50 2.8 240 - - Fig.7 mode 3; I13 >-135 µA; R15 = 22 k Io = 1 mA 0.9 - - - Io max (100%) Io min (typically 58%) Horizontal comparator PLL1 V17 I17 upper control voltage limitation lower control voltage limitation control current Fig.6 - - - 5.9 5.1 ±0.083I18 -110 - 1.0 - - 42 - 3.0 300 ±200 - 0.6 - - 1.9 5.4 2.9 - 0.8 60 - 1.4 - - MIN. TYP.
TDA4852
MAX. - 1.6 ±10 300
UNIT
Vertical sync input (DC-coupled, TTL-compatible) Vi sync sync input signal (peak-to-peak value, pin 10) slicing level I10 tp V input current maximum vertical sync pulse width for automatic vertical polarity switch
V V µA µs
Horizontal clamping / blanking generator output V8 output voltage LOW blanking output voltage clamping output voltage I8 t8 tclp S internal sink current for all output levels external load current clamping pulse start clamping pulse width steepness of rise and fall times
0.9 2.2 5.65 3.5 -3.0 1.0 75 - 110 3.2 360 - 0.18
V V V mA mA µs ns/V
with end of H-sync
Vertical oscillator f0 fv V15 td I12 C12 Io vertical free-running frequency nominal vertical sync range voltage on pin 15 delay between sync pulse and start of vertical scan control current for amplitude control capacitor for amplitude control
Hz Hz V µs µA µF
Vertical differential output differential output current between pins 5 and 6 (peak-to-peak value) maximum offset-current error maximum linearity error
1.1 ±2.5 ±1.5 - -135 - - - -
mA % %
Vertical amplitude adjustment (in percentage of output signal) V13 I13 input voltage adjustment current 5.0 -120 0 V µA µA
V V mA
December 1992
8
Philips Semiconductors
Preliminary specification
Horizontal and vertical deflection controller for autosync monitors
SYMBOL Horizontal oscillator fosc centre frequency deviation of centre frequency temperature coefficient H/tH I18 V18 relative holding/catching range external oscillator current voltage at reference current input (pin18) Fig.6 I2 = 6 mA I2 = -1 mA - - - - - - - 30 Fig.6 I3 = 20 mA I3 = 60 mA tp/tH VP tH tH duty factor threshold to activate under voltage protection jitter of horizontal output horizontal output off horizontal output on f = 31 kHz f = 64 kHz f = 100 kHz E/W output V11 bottom output signal during mid-scan (pin 11) top output signal during flyback temperature coefficient of output signal E/W amplitude adjustment (parabola) V14 I14 input voltage (pin 14) adjustment current 100% parabola typically 28% parabola Note to the characteristics Fig.7 - -110 - 5.0 -120 0 note 1 internally stabilized 1.05 4.2 - 1.2 4.5 - - - 42 - - - - - - - 45 5.6 5.8 - - - 5.5 -0.75 3.0 3.0 6.2 4.8 ±0.083I18 - R18 = 2.4 k (pin 18); C19 = 10 nF (pin 19) - - 0 ±6 -0.5 2.35 31.45 - +200 ±6.5 - 2.5 PARAMETER CONDITIONS MIN. TYP.
TDA4852
MAX. - ±3 +300 ±7.3 -4.3 2.65
UNIT
kHz % 10-6/K % mA V
Horizontal PLL2 V2 upper clamping level of flyback input lower clamping level of flyback input H-flyback slicing level td/tH V20 I20 t/tH V3 delay between middle of sync and middle of H-flyback related to tH upper control voltage limitation lower control voltage limitation control current PLL2 control range related to tH output voltage LOW
- - - - - - - -
V V V % V V µA %
Horizontal output (open-collector)
0.3 0.8 48 - - 3.5 1.9 1.2
V V % V V ns ns ns
1.35 4.8 250 - -135 -
V V 10-6/K
V µA µA
1. Parabola amplitude does not track with vertical amplitude adjustment. Tracking can be achieved by a resistor from vertical amplitude potentiometer to pin 14. December 1992 9
Philips Semiconductors
Preliminary specification
Horizontal and vertical deflection controller for autosync monitors
APPLICATION INFORMATION
TDA4852
Note: pin 7 has to be connected to ground to avoid crosstalk from pin 8 to pin 6.
Fig.3 Application circuit for 31.45 kHz.
Note: pin 7 has to be connected to ground to avoid crosstalk from pin 8 to pin 6.
Fig.4 Application circuit for 64 kHz.
December 1992
10
Philips Semiconductors
Preliminary specification
Horizontal and vertical deflection controller for autosync monitors
TDA4852
Note: pin 7 has to be connected to ground to avoid crosstalk from pin 8 to pin 6.
Fig.5 Application circuit for 31 to 64 kHz.
(1) tracks with PLL1 control voltage at pin 17
Fig.6 Horizontal timing diagram.
December 1992
11
Philips Semiconductors
Preliminary specification
Horizontal and vertical deflection controller for autosync monitors
TDA4852
(1) for free-running oscillator
Fig.7 Vertical and E/W timing diagram.
December 1992
12
December 1992
Philips Semiconductors
Horizontal and vertical deflection controller for autosync monitors
13
(1) (2) (3) (4) (5)
clamp pulses triggered by H-sync clamp pulses triggered by leading edge of V-trigger pulse clamp pulses triggered by horizontal oscillator during V-trigger pulse clamp pulses are generated internally control voltage of PLL1 is corrected during V-trigger pulse
Preliminary specification
TDA4852
Fig.8
Pulse diagram for composite sync applications (showing reduced influence of V-sync on H-phase and drive pulses for F/V converters).
Philips Semiconductors
Preliminary specification
Horizontal and vertical deflection controller for autosync monitors
TDA4852
December 1992
14
Fig.9 Internal circuits.
Philips Semiconductors
Preliminary specification
Horizontal and vertical deflection controller for autosync monitors
PACKAGE OUTLINE DIP20: plastic dual in-line package; 20 leads (300 mil)
TDA4852
SOT146-1
D seating plane
ME
A2
A
L
A1
c Z e b1 b 20 11 MH w M (e 1)
pin 1 index E
1
10
0
5 scale
10 mm
DIMENSIONS (inch dimensions are derived from the original mm dimensions) UNIT mm inches A max. 4.2 0.17 A1 min. 0.51 0.020 A2 max. 3.2 0.13 b 1.73 1.30 0.068 0.051 b1 0.53 0.38 0.021 0.015 c 0.36 0.23 0.014 0.009 D
(1)
E
(1)
e 2.54 0.10
e1 7.62 0.30
L 3.60 3.05 0.14 0.12
ME 8.25 7.80 0.32 0.31
MH 10.0 8.3 0.39 0.33
w 0.254 0.01
Z (1) max. 2.0 0.078
26.92 26.54 1.060 1.045
6.40 6.22 0.25 0.24
Note 1. Plastic or metal protrusions of 0.25 mm maximum per side are not included. OUTLINE VERSION SOT146-1 REFERENCES IEC JEDEC EIAJ SC603 EUROPEAN PROJECTION
ISSUE DATE 92-11-17 95-05-24
December 1992
15
Philips Semiconductors
Preliminary specification
Horizontal and vertical deflection controller for autosync monitors
SOLDERING Introduction There is no soldering method that is ideal for all IC packages. Wave soldering is often preferred when through-hole and surface mounted components are mixed on one printed-circuit board. However, wave soldering is not always suitable for surface mounted ICs, or for printed-circuits with high population densities. In these situations reflow soldering is often used. This text gives a very brief insight to a complex technology. A more in-depth account of soldering ICs can be found in our "IC Package Databook" (order code 9398 652 90011). Soldering by dipping or by wave The maximum permissible temperature of the solder is 260 °C; solder at this temperature must not be in contact DEFINITIONS Data sheet status Objective specification Preliminary specification Product specification Limiting values
TDA4852
with the joint for more than 5 seconds. The total contact time of successive solder waves must not exceed 5 seconds. The device may be mounted up to the seating plane, but the temperature of the plastic body must not exceed the specified maximum storage temperature (Tstg max). If the printed-circuit board has been pre-heated, forced cooling may be necessary immediately after soldering to keep the temperature within the permissible limit. Repairing soldered joints Apply a low voltage soldering iron (less than 24 V) to the lead(s) of the package, below the seating plane or not more than 2 mm above it. If the temperature of the soldering iron bit is less than 300 °C it may remain in contact for up to 10 seconds. If the bit temperature is between 300 and 400 °C, contact may be up to 5 seconds.
This data sheet contains target or goal specifications for product development. This data sheet contains preliminary data; supplementary data may be published later. This data sheet contains final product specifications.
Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information Where application information is given, it is advisory and does not form part of the specification. LIFE SUPPORT APPLICATIONS These products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips for any damages resulting from such improper use or sale.
December 1992
16