Text preview for : ROLSEN RL-17S10, MAIN 111-A40A.pdf part of ROLSEN RL-17S10 TFT-LCD Service Manual
Back to : ROLSEN RL-17S10, MAIN 111 | Home
COLOR TFT-LCD TV
SERVICE MANUAL
MODEL : RL-17S10
CAUTION !!
BEFORE SERVICING THE TFT-LCD TV,
READ THE SAFETY PRECAUTIONS IN THIS MANUAL.
RL-17S10 SERVICE MANUAL PAGE:1
CONTENTS
Contents ------------------------------------------------------------------------ 2
Safety Precautions ---------------------------------------------------------- 3
Servicing Precautions ------------------------------------------------------ 4
Specifications ----------------------------------------------------------------- 5
Control Descriptions -------------------------------------------------------- 10
External In/Out Ports -------------------------------------------------------- 13
Adjustment --------------------------------------------------------------------- 14
Block Diagram ----------------------------------------------------------------- 18
Schematic Diagram ---------------------------------------------------------- 19
Wave Form ---------------------------------------------------------------------- 20
Troubleshooting --------------------------------------------------------------- 25
Replacement Parts List ----------------------------------------------------- 27
PCB Layout --------------------------------------------------------------------- 34
Exploded View ----------------------------------------------------------------- 39
RL-17S10 SERVICE MANUAL PAGE:2
SAFETY PRECAUTIONS
!! Important Safety Notice !!
Many electrical and mechanical parts in this chassis have special safety-related
characteristics.
These parts are identified by in the Schematic Diagram and Replacement Parts List.
It is essential that these special safety parts should be replaced with the same components
as recommended in this manual to prevent Shock, Fire, or other Hazards.
Do not modify the original design without permission of manufacturer.
Leakage Current Hot Check (See below Figure)
Plug the AC cord directly into the AC outlet.
Do not use a line Isolation Transformer during this check.
Connect 1.5K/10watt resistor in parallel with a 0.15uF capacitor between a known good
earth ground (Water Pipe, Conduit, etc.) and the exposed metallic parts.
Measure the AC voltage across the resistor using AC voltmeter with 1000 ohms/volt or
more sensitivity.
Reverse plug of the AC cord into the AC outlet and repeat AC voltage measurements for
each exposed metallic part. Any voltage measured must not exceed 0.75 volt RMS, which
is, corresponds to 0.5mA.
In case any measurement is out of the limits specified, there is possibility of shock hazard
and the set must be checked and repaired before it is returned to the customer.
Leakage Current Hot Check circuit
RL-17S10 SERVICE MANUAL PAGE:3
SERVICING PRECAUTIONS
CAUTION!!
Before servicing receivers covered by this service manual, read and follow the SAFETY
PRECAUTIONS on page 3 of this publication.
General Servicing Precautions
1.Always unplug the receiver AC power cord from AC power source before;
¨Í Removing or reinstalling any component, circuit board module or any other receiver
assembly.
¨Î Disconnecting or reconnecting any receiver electrical plug or other electrical connection.
¨Ï Connecting a test substitute in parallel with an electrolytic capacitor in the receiver.
CAUTION!! A wrong part substitution or incorrect polarity installation of electrolytic
capacitors may result in an explosion harzard.
2.Do not spray chemicals on or near this receiver or any of its assemblies.
3.Do not defect any plug/socket voltage interlocks with which receivers covered by this
service manual might be equipped.
4.Always connect the test receiver ground lead to the receiver chassis ground before
connecting the test receiver positive lead. Always remove the test receiver ground lead last.
5.Do not connect the test fixture ground strap to power supply heatsink in this receiver
Electrostatically Sensitive(ES) Devices
Some semiconductor(solid state) devices can be damaged easily by static electricity. Such
components commonly are called Electrostatically Sensitive(ES) Device.Examples
Circuit Board Foil Repair
Excessive heat applied to the copper foil of any printed circuit board will weaken the
adhesive that bonds the foil to the circuit board causing the foil th separate from or "lift-off"
the board.
The following guidelines and procedures should be flollowed whenever this condition is
encountered.
At IC Connections
To repair a defective copper pattern at IC connections use the following procedure to install
a jumper wire on the copper pattern side of the circuit board.(Use this technique only on IC
connections.)
1.Carefully remove the damaged copper pattern with a sharp knife.(Remove only as much
copper as absolutely necessary.)
2.Carefully scratch away the solder resist and acrylic coating(if used) from the end of the
remaining coopper pattern.
3.Bend a small "U" in one end of a small guage jumper wire and carefully crimp it around
the IC pin.
4.Route the jumper wire along the path of the out-away copper pattern and let it overlap
the previously scraped end of the good copper pattern. Solder the overlapped area and
clip off any excess jumper wire.
RL-17S10 SERVICE MANUAL PAGE:4
SPECIFICATIONS
Note: Specifications and others are subject to change without notice for improvement.
1. Scope.
This document is the specification of 17.1" TFT-LCD Color TV.
2. Power
1) Power requirement
DC 12V / 5.0A
2) AC / DC Adapter.
Input Frequency : 50/60§Ô ¡¾ 3§Ô
Input Voltage : AC 110V ¡- AC 240V (¡¾ 10%)
Output Voltage : DC 12V
3) Power cord
Use UL listed and CSA certified detachable power cord type:SVT, 3-conductors, 18AWG
for AC 120V area.
Use VDE listed detachable power cord type:H05VV-F, 3-conductors, 18AWG for AC220
~240V area.
3. Tuning system
FS, 181 Channel
4. Sound output
1.5W+1.5Wrms Stereo (Max)
5. Antenna input impedance
VHF / UHF at 75ohm
6. OSD Type (On Screen Display)
Windows type (Center)
7. External in/output
Component, AV, Head Phone, PC, PC sound in
Audio In : 0.4Vrms, over 10K§Ù
Video In : 1Vp-p, over 75§Ù
8. Function
CATV/Hyper band
Auto Program
Manual Program
Auto Sleep
Quick view
ACMS(Auto channel Memory System)
PSM(Picture Status memory)
SSM(Sound Status memory)
ARC(Aspect Ratio Control)
RL-17S10 SERVICE MANUAL PAGE:5
SPECIFICATIONS
9. Receiving RF TV system
NO RL-17S10 / /
Model System
1 PAL-B ¡ Û / /
2 PAL-G ¡ Û / /
3 PAL-I, I /I ¡ Û / /
4 PAL-D ¡ Û / /
5 PAL-K ¡ Û / /
6 SECAM-B ¡ Û / /
7 SECAM-G ¡ Û / /
8 SECAM-D ¡ Û / /
9 SECAM-K ¡ Û / /
10 SECAM-K1 ¡ Û / /
11 SECAM-I (6.0) ¡ Û / /
12 NTSC-3.58 / 4.5 ¡ Û / /
13 NTSC-3.58 / 5.5 ¡ Û / /
14 NTSC-3.58 / 6.0 ¡ Û / /
15 NTSC-3.58 / 6.5 ¡ Û / /
16 NTSC-3.58 / 4.5(5.0) ¡ Û / /
17 NTSC-4.43 / 5.5 ¡ Û / /
18 NTSC-4.43 / 6.0 ¡ Û / /
19 NTSC-4.43 / 6.5 ¡ Û / /
20 PAL 5.5 / 60Hz ¡ Û / /
21 PAL 6.0 / 60Hz ¡ Û / /
22 PAL 6.5 / 60Hz ¡ Û / /
23 SECAM 5.5 / 60Hz ¡ Û / /
24 SECAM 6.0 / 60Hz ¡ Û / /
25 SECAM 6.5 / 60Hz ¡ Û / /
26 SECAM L / L' X / /
TOTAL SYSTEM 25 / /
RL-17S10 SERVICE MANUAL PAGE:6
SPECIFICATIONS
10. Receiving function & channel
NO Receiving System Function Receiving Channel
1 PAL-B
2 PAL-G
3 PAL- I, I / I
VHF Band
4 PAL-D
NTSC-M (US) : 2-13
5 PAL-K NTSC-M (JAPAN) : 1-12
Reception of broadcast
6 SECAM-B and play-back for Video
UHF Band
Tape Recorder
7 SECAM-G NTSC-M (US) : 14-78
NTSC-M (JAPAN) : 13-62
8 SECAM-D
9 SECAM-K
10 SECAM-K1
11 NTSC-M
12 SECAM-L / L'
13 NTSC-4.43 / 5.5
14 NTSC-4.43 / 6.0 Play-back for special
NTSC 3.58/4.5MHz/60Hz only
15 NTSC-4.43 / 6.5 Video Tape Recorder
16 SECAM-I (6.0MHz)
17 SECAM-L (VIDEO IN)
18 NTSC 3.58 / 4.5MHz / 50Hz
19 PAL 5.5MHz / 60Hz
20 PAL 6.0MHz / 60Hz
Play-back for special
21 PAL 6.5MHz / 60Hz Video Tape/Video disk NTSC 3.58/4.5MHz/60Hz only
player
22 SECAM 5.5MHz/60Hz
23 SECAM 6.0MHz/60Hz
24 SECAM 6.5MHz/60Hz
25 NTSC-3.58 / 5.5MHz
Play-back for special
26 NTSC-3.58 / 6.0MHz
Video Tape Recorder
27 NTSC-3.58 / 6.5MHz
RL-17S10 SERVICE MANUAL PAGE:7
SPECIFICATIONS
11. PC/DTV Mode Scan Frequency & Timing
1)Scan Freq : H: 31 ¡- 68.7 KHz / V : 56 ¡- 85§Ô
2)Preset Timing Chart
Mode Resolution H-Freq(Khz) V-Freq(Khz)
640x480 31.5KHz 60Hz
640x480 37.9KHz 72Hz
VGA 640x480 37.5KHz 75Hz
640x480 43.3KHz 85Hz
720x400 31.5KHz 70Hz
800x600 35.1KHz 56Hz
800x600 37.9KHz 60Hz
SVGA 800x600 48.1KHz 72Hz
800x600 46.9KHz 75Hz
800x600 53.7KHz 85Hz
1024x768 48.4KHz 60Hz
1024x768 56.5KHz 70Hz
XGA 1024x768 60.2KHz 75Hz
1024x768 68.7KHz 85Hz
1920x1080i 33.8KHz 60Hz
DTV 1280x720i 45KHz 60Hz
720x480p 31.5KHz 60Hz
Note!! :
¨Í If the set is cold, there may be a small "flicker" when the set is switched on. This is
Normal, there is nothing wrong with the set.
¨Î If possible, use the VESA 1024x768 PC video mode to obtain the best image
quality for your LCD TV.
¨Ï Some dot defects may appear on the screen, like Red, Green or Blue spot. however,
this will have no impact or effect on the monitor performance.
RL-17S10 SERVICE MANUAL PAGE:8
SPECIFICATIONS
12. TFT LCD Panel Character
1) Feature
Size : 17.1" Diagonal (43Cm)
LCD Type : Color Active Matrix TFT
Pixel Pitch : 0.291mm x 0.291mm
Pixel Format : 1280x768 Pixels, RGB Stripe
Active Video Area : 372.48mm(H) x 223.488mm(V)
Surface treatment : Anti-Glare, Hard coating(3H)
Response Time(Typ) :25ms(Typ)
Viewing Angle : Hor [Left/Right] 88Deg (Typ) / 88Deg (Typ),
Ver [High(Top)/Low(Bottom)] 88Deg (Typ) / 88Deg (Typ)
Luminance(Typ) : 450 cd/§³ (Typ)
Contrast Ratio(Typ) : 400(Typ)
Display Color : 16,777,216 Color
Back Light : 6 CCFL
RL-17S10 SERVICE MANUAL PAGE:9
CONTROL DESCRIPTIONS
All the function can be controlled with the remote controller.
Some functions can also adjusted with the buttons on the controls on the TV front panel.
Remote controller
Note !! : Before you use the remote controller, please install the batteries.
1. POWER
Turns the TV on from standby or off to
standby mode.
2. MUTE
Turns the sound on and off
3. NUMBER buttons
Selects programme numbers.
4. PSM (Picture Status Memory)
Recalls your preferred picture setting.
5. SSM (Sound Status Memory)
Recalls your preferred sound setting.
6. TV / AV
Selects TV, COMPONENT, VIDEO,
S-VIDEO or PC mode.
Clears the menu from the screen.
7. MENU
Displays a main menu.
8. I / II
Selects the language during dual
language broadcast.
Selects the sound output.
9. Q.VIEW
Returns to the previously viewed
channel.
RL-17S10 SERVICE MANUAL PAGE:10
CONTROL DESCRIPTIONS
Remote controller
Note !! : Before you use the remote controller, please install the batteries.
10. PR å¡ã (Programme Up/Down)
Selects next programme or a menu
item.
11. OK
Accepts your selection or displays the
current mode.
12. VOL º¢¸ (Volumn Up/Down)
Adjusts the sound level or a menu
Setting.
13. SLEEP
Sets the sleep timer.
Note: In Teletext mode, the Sleep button
is used for Teletext function.
14. Teletext buttons
These buttons are used for Teletext.
For further details, see the `Teletext'
section.
15. ARC (Aspect Ratio Control)
Selects a screen mode 16:9 or 4:3.
16. SCART
Selects the SCART mode.
17. VIDEO
Selects the VIDEO mode.
18. S-VIDEO
Selects the S-VIDEO mode.
19. PC
Selects the PC mode.
RL-17S10 SERVICE MANUAL PAGE:11
CONTROL DESCRIPTIONS
Controller of Panel
1. ON/OFF
Switches TV set on or off.
2. MENU
Display a menu.
-
3. + PR ( Programme Up/Down)
Selects a programme or a menu item.
-
4. + VOL ( Volume Up/Down)
Adjusts the sound level or a menu Setting
5. TV/AV
Selects input signal source.
Clears the menu from the screen.
6. POWER STAND-BY INDICATOR
Illuminates red when the TV is in power
stand-by mode.
Illuminates green when the TV is switched
power on mode.
7.REMOTE CONTROL SENSOR:
¡Ý ¡Ý Accepts the IR signal of remote controller.
RL-17S10 SERVICE MANUAL PAGE:12
EXTERNAL IN/OUT PORTS
External IN / OUT
1. DC 12V Adapter INPUT
2. PC/DTV INPUT
3. PC Audio IN
Connect the audio cable from the PC to the PC Audio IN of the set.
4. COMPONENT IN (Y, Cb, Cr, L, R)
Connector the RCA cable from the DVD or VCR to the COMPONENT IN of the set.
5. H/P
Connect a headphone to this socket.
6. S-VIDEO
Connect the output of an S-VIDEO VCR to the S-VIDEO input.
Connect the audio outputs of an S-VIDEO VCR to the AV-IN audio inputs.
7. A/V IN inputs
Connect the Audio/Video outputs of external equipment to these inputs.
8. ANT(Antenna input)
Connect the RF cable from the ANT Port of home or office to the ANT. of the set.
RL-17S10 SERVICE MANUAL PAGE:13
ADJUSTMENT
1. Safety Precautions
1. Never disconnect leads while the TV receiver is on.
2. Don't short any portion of circuits while power is on.
3. The adjustment must be done by the correct appliances. But this is changeable in
view of productivity.
4. Unless otherwise noted, set the line voltage to 230Vac 10%, 50Hz ./ 110Vac, 60Hz
2. Test Equipment required
1. RF signal generator (with pattern generator)
2. Multi meter (volt meter)
3. Oscilloscope
4. LCD Color analyzer
3. RF AGC (Automatic Gain Control) Adjustment
Note!! Adjust a RF AGC of world standard tuner only.
2 in 1 tuner need not AGC adjust.
The RF AGC was aligned at the time of manufacture for optimum performance over a wide
range conditions. Readjustment of RF AGC should not be necessary unless unusual local
conditions exist, such as ;
1) Channel interference in a CATV system.
2) Picture bending and/or color beats, which are unusually due to excessive RF signal
input when the receiver is too close to a transmitting tower or when the receiver is
connected to an antenna distribution system where the RF signal has been
amplified. In this case, the input signal should be attenuated (with pad or filter) to a
satisfactory level.
3) Picture noise caused by "broadcast noise" or weak signal. If the broadcast is
"clean" and the RF signal is at least 1mV (60dBu), the picture will be noise free in
any area.
Adjusting RF AGC to one end of rotation will usually cause a relatively poor signal to noise
ratio; Adjusting to the other end of rotation will usually cause a degradation of over load
capabilities resulting in color beats or adjacent channel interference.
Adjustment Note!!
1. Connect RF signal (65dB± 0.5dB) and turn on the TV.
2. Press MENU buttons on TV set and Remote Controller at the same time to get into
SVC mode.
3. Press YELLOW button on the Remote Controller several times to find AGC.
4. Press Volume UP/DOWN button until the AGC Voltage is the same as the Table
below.
5. Press OK button to memorize the data.
6. Press TV/AV button to exit SVC mode.
RL-17S10 SERVICE MANUAL PAGE:14
ADJUSTMENT
4. SVC Data Adjustment
NOTE!! When the EEPROM has been replaced, the SVC data should be restored as the
function of individual system and specification.
1) Press 5 Seconds MENU buttons on both TV set and Remote Controller at the same
time to get into SVC mode.
2) Press the Yellow button several times to find SVC Data.
3) Input the corresponding SVC data referring to Table below with the Volume
Up/down key.
4) Press the OK button to memorize the data.
5) Press TV/AV button to exit SVC mode
5-1. SVC Data Table
PAGE ITEM VALUE1 VALUE2 REMARK
AGC 20 Variable Data(0-31)
RD 80 PC Contrast Coefficient-RED(0-255)
GD 80 PC Contrast Coefficient-GREEN(0-255)
DATA 1
BD 80 PC Contrast Coefficient-BLUE(0-255)
RO 32 PC Brightness Coefficient-RED(0-63)
GO 32 PC Brightness Coefficient-GREEN(0-63)
BO 32 PC Brightness Coefficient-BLUE(0-63)
S-B 20 PC Sub-Brightness(0-31)
PC CP 0 PC Charge Pump(0-7)
50 PR * * means current program NO.
FP 21 FM Prescaler(0-127)
NP 89 NICAM Prescaler(0-127)
SP 50 SCART Prescaler(0-127)
DATA 2
S1 VOL 105 SCART1 Volume(0-127)
S2 VOL 105 SCART2 Volume(0-127)
50 PR * * means current program NO.
0 100PR
200PR 0
1 200PR
0 Not apply to TEXT
TEXT 1
1 Apply to TEXT
0 TELETEXT TOP OFF
TOP 1
1 TELETEXT TOP ON
0 Apply to COMPONENT
SCART 0
1 Apply to SCART
DATA 3 0 Not apply to ACMS
ACMS 1
1 Apply to ACMS
0 Used except for CHINESS or AUSTRALIA
CH+AU 0
1 Used CHINESS or AUSTRALIA
0 BG/I/DK
SYS 2 1 BG/I/DK/L
2 BG/I/DK/M
50 PR * * means current program NO.
106 Opt 1 Translate HEX into DEC(DATA3VALUE1)
RL-17S10 SERVICE MANUAL PAGE:15
5-2. SVC Data Table
PAGE ITEM VALUE1 VALUE2 REMARK
0 Not apply to DUAL option
DUAL 0
1 Apply to DUAL option
0 Not apply to MONO option
MONO 0
1 Apply to MONO option
0 Not apply to NICAM STEREO option
A2 ST 1
1 Apply to NICAM STEREO option
0 Sound curve option 1
VOL 1
1 Sound curve option 2
0 Not apply to YUV / SCART
AV1 1
1 Apply to YUV OR SCART
0 6-KEY Key option
KEY 0
1 4-KEY
0 ENG ONLY ENGLISH ONLY
ENGLISH/GERMAN/FRANCE/ITALY/
1 EU-5EA
SPAIN
2 EU CIS EU-5EA + CIS
LANG 2 3 E+CHINA ENGLISH + CHINESS
4 E+HUNGARY ENGLISH+ HUNGRAY
5 RESERVED
6 RESERVED
7 RESERVED
DATA 4 WEST EU U.K/GERMAN/FRANCE/
0 WEST EU ITALY/SPAIN/SWEDEN/CZECH
Rep./NORWAY etc
1 EAST EU1 POLAND/SLOVENIA/ROMANIA etc
2 TURKEY EU TURKEY
3 EAST EU2 HUNGRY/SERVIA
4 CYRILLIC1 ESTONIA
5 CYRILLIC2 ESTONIA
RUSIA/UKRAINE/ESTONIA/CROATI
6 CYRILLIC3
A/KAZAKHSTAN
T-LAN 6
7 TURK GRE1
8 TURK GRE2
9 TURK GRE3 TURKEY/GREECE
10 ARAB ERA
11 ARAB ENG ARAB CULTURE
12 ARAB HEB1
13 ARAB HEB2 ARAB/HEBREW
14 FARS ENG PARSI
15 FARS FRA
16 FARS ALL
50 PR * * means current program NO.
57 Opt 2 Translate HEX into DEC(DATA4)
RL-17S10 SERVICE MANUAL PAGE:16
ADJUSTMENT
6.AGC Adjustment (SVC Data 1)
Note!! Adjust a RF AGC of world standard tuner only.
2 in 1 tuner need not AGC adjust.
Test point : AGC pin of Tuner
Adjust : Remote Controller
1) Connect RF signal (65±, 0.5dB§Å ) and tune on the TV.
Standard adjustment channel
- 07CH (frf = 175.25MHZ)
2) Press 5 seconds MENU buttons on TV set and Remote controller at the same time
to get into SVC Data.
3) Press the channel up/down button on the Remote Controller several times to find
AGC??
6) Press the volume up/down button until the AGC voltage is the same as Table below.
7) Press OK button to memorize the data.
7.Optional Function
OPTION CODE FUNCTION REMARK
0 6-KEY Local key option
KEY
1 4-KEY
0 W/O COMPONENT Disable
AV1
1 COMPONENT Enable
0 AMERICA English, French, Espanol
1 ENG 2EA English, Espanol, Portugunese
LANG
2 KOREA Korea,
3 RESERVED English
0 AMERICA Tuning option of each country
1 KOREA
TUNE
2 JAPAN
3 RESERVED
RL-17S10 SERVICE MANUAL PAGE:17
BLOCK DIAGRAM
Block Diagram
`
RL-17S10 SERVICE MANUAL PAGE:18
WAVE FORM
NOTE!!:¨Í Video = Gray scale pattern input / Audio = 1Khz input at volume step 40.
¨Î You can find number from Schematic Diagram
1)Component Y input, 2)Component Cb input,
(1V-p-p, Input = Vertical color pattern) (0.7V-p-p, Input = Vertical color pattern)
3) Component Cr input,
(0.7V-p-p, Input = Vertical color pattern) 4) S-video C signal input.
5) S-video Y signal input.(15.7Khz,1Vp-p) 6) CVBS Video signal input.(15.7Khz,1Vp-p)
RL-17S10 SERVICE MANUAL PAGE:20
WAVE FORM
NOTE!!: Video = Gray scale pattern input / Audio = 1Khz input at volume step 40.
7) Tuner sound IF output (4.5Mhz) 8)Tuner mono audio output
9) Tuner 33V input (about 32V~34V) 10)Tuner CVBS video output (15Khz,1Vp-p)
11)IC601 Pin#27,28 Audio output. 12)IC605 Audio output
RL-17S10 SERVICE MANUAL PAGE:21
WAVE FORM
NOTE!!: Video = Gray scale pattern input / Audio = 1Khz input at volume step 40.
13) IC501 Pin#28 clock output.(13.6Mhz,1.25Vp-p) 14) IC501 Pin#54 clock output.(15.7Khz,3.5Vp-p)
15) IC501 Pin#56 clock output.(15.7Khz,3.5Vp-p) 16) IC501 Pin#57 clock output.(50Hz,3.5Vp-p)
17)IC804 Output (ST-BY DC 5V) 18) IC803 Output (DC 12V)
RL-17S10 SERVICE MANUAL PAGE:22
WAVE FORM
NOTE!!: Video = Gray scale pattern input / Audio = 1Khz input at volume step 40.
19) IC801 Output (DC 5V) 20)IC801 OSC (about 52Khz, 12Vp-p)
21)IC802 OSC (Tuner 33V input) 22)Panel Dot clock input (80.53Mhz,0.7Vp-p)
23) Panel DE clock input 24) Panel VSync input (60Hz,3.5Vp-p)
RL-17S10 SERVICE MANUAL PAGE:23
WAVE FORM
NOTE!!: Video = Gray scale pattern input / Audio = 1Khz input at volume step 40.
25) Panel HSync input (31.6Khz,3.5Vp-p) 26)P805 Pin#5 Inverter on/off (High=on)
RL-17S10 SERVICE MANUAL PAGE:24
TROUBLE SHOOTING
No Raster or Maximum White? Yes Fasten P03
Maximum White Connector
No
Check P803 12V Check appropriate
On/off: High No Circuit.(Power
ADJ-BRI : 0V Supply & u-Com
Control)
Yes
Check Inverter No Replace Inverter
output.
Yes
Replace LCD
Module
No picture & Is OSD O.K? Yes Check IC01
Sound OK Pin70(LLC)
No Pin99(FPHS)
Check IC501 Pin100(FPVS)
Pin 28/54/56/57 Pin101(FPDE)
O.K? O.K?
Yes
Yes No
Check IC501
Video Inputs Check signals
Pin71 ~ 75 From IC01~
IC05~P03
Check Vcc, X-tal
And IIC of IC01
RL-17S10 SERVICE MANUAL PAGE:25
TROUBLE SHOOTING
No Sound & Check IC601 Check appropriate
Picture OK Inputs No Signal inputs from
(Pin50/51/53/54/ Ic601 to signal
56/57/60/61/67) Source.
Yes
Check IC601 No Check IC601
Vcc/X-tal/IIC Outputs Pin27/28
Yes
Check IC605 Check IC605
Outputs(Pin7/11) No Vcc
O.K? Mute (Pin8 Low)
Yes
Check
Headphone
Jack of J402
No Text Check IC101 No Check CVBS
Pin12 (CVBS) Signal from Pin70
of IC501 to Pin12
of IC101
Yes
Check Pin38~41
of IC101
(R.G.B.FB) No Replace IC101
Yes
Check
Pin 1/2/3/79
of IC501
RL-17S10 SERVICE MANUAL PAGE:26
REPLACEMENT PART LIST
1.Parts List (Assemble process)
LEVEL PART NO PART NAME DESCRIPTIONS Q,TY
1 300-003L BOX, ACCESSORY 17.1" N/F MODEL COMMON 1
1 300-009N BOX, GIFT RL-17S10(LT-17FTP), RUS, ROLSEN 1
1 310-013C PACKING, LEFT 17.1" F/N MODEL COMMON 1
1 310-013D PACKING, RIGHT 17.1" F/N MODEL COMMON 1
1 320-001A BAG, VINYL ACCESSORY PACKING 1
1 321-002A BAG, PACKING 15.1" A/E SET PACKING 1
1 322-001A HANDLE, UP 15.1" HANDLE 1
1 322-001B HANDLE, DOWN 15.1" HANDLE 1
1 401-002X COVER, BACK 17.1" F/N MODEL, COLOR:GRAY 1
1 402-005A COVER, HINGE 17.1" N MODEL COMMON, LEFT 1
1 402-005B COVER, HINGE 17.1" N MODEL COMMON, RIGHT 1
1 404-004A BLOCK KNOB F/N-MODEL, LOCAL KEY, Chromium 1
1 407-001M SHIELD, FRONT 17.1", F/N MODEL COMMON 1
1 407-002J SHIELD, REAR 17.1" F/N MODEL COMMON, PCB ASSY COVER 1
1 407-003Q SHIELD, JACK 17.1" IPS MODEL, YUV 1
1 410-001K SCREW TTB 3*8 22
1 410-001N SCREW FTB 3*6 12
1 410-001P SCREW FTB 3*4 10
1 410-001Q SCREW BTB 4*12 10
1 410-002Q SCREW PS 4*10 4
1 450-001S DECO PLATE 17.1" N/F MODEL COMMON, PAL/NTSC 1
1 490-001J FORM, SHIELD GASKET, 71TS 7-NO.3-260-00 1
1 490-011C FORM, SHIELD GASKET, 71TS-FK 20-2-34-13-S 1
1 490-011D FORM, SHIELD GASKET, 71TS-FK 7-0.5-100-13 1
1 490-011E FORM, SHIELD GASKET, 71TS-FK 7-0.5-90-13 1
1 490-011F FORM, SHIELD GASKET, 71TS-FK 7-0.5-45-13 1
1 490-011G FORM, SHIELD GASKET, 71TS-FK 12-2.5-30-13 1
1 491-001A TAPE, CONDUCTIVE W:40mm,L:20mm, COPPER 3
1 492-001A FERRITE CORE CLIP CORE, ZCAT13250530 1
1 492-001C FERRITE CORE CLIP CORE, ZCAT1518-0730 1
1 499-001C TAPE, Åõ¸í W:20mm 130mm
1 499-002A TAPE, Åõ¸í W:70mm 1300mm
1 499-004A TAPE, ACETATE W:20mm, L:30m 200mm
1 500-003X OWNER'S MANUAL RL-17S10(LT-17FTP), RUS, ROLSEN 1
1 501-001R LABEL, WARNING ROLSEN/ELSON, RUS 1
1 501-0030 LABEL, SERIAL ¿øÀÚç, SILVER /BLACK 1
1 501-016F STICKER,LOGO ROLSEN, 15/17" SIZE 40MM 1
1 501-062J LABEL, ID RL-17S10(LT-17FTP), RUS, ROLSEN 1
1 502-0010 LABEL, BOX ID CARTON BOX, ALL MODEL 1
1 507-001A LABEL, PROTECTIVE PANEL FILM FIX 2
1 510-011A REMOCON NO BRAND,ARC,PR,TEXT,ENG 1
1 520-001A BATTERY 1.5V, AAA SIZE 2
1 522-001M WARRANTY CARD ROLSEN, COMMON, RUS 1
1 610-004A SPEAKER 3W, 4 OHM 2
1 620-001C AC/DC ADAPTER 12V, 5.0A 1
1 621-001B POWER CORD 250V, 2-PIN,1.8M, BK, VDE KKP-4819R 1
1 622-005B INVERTER, DC-AC 17.1", FIF1766-31A 1
1 626-001A CABLE, PC RGB IVORY, 1.8M, 15-PIN 1
1 627-001A CABLE, PC-SOUND 1.8M, BK 1
1 AYCALT21B02A CABINET ASS'Y 17.1" F MODEL, PR 1
1 AYCOLT32A01A CONTROL PCB ASS'Y F/N MODEL, 111-A34A-30 CONTROL 1
1 AYMALT17A01C MAIN PCB ASS'Y LT-17TP, YUV+MSP3410D+TAFD-Z242D 1
1 AYSTLT21B02A STAND ASS'Y 17.1" F MODEL 1
1 CON02P200A0L LEAD ASSY 17.1" SPK, 2-PIN 270MM 1
1 CON03P200A0S LEAD ASSY 17.1" SPK, 3-PIN 600MM 1
1 CON05P200ABH LEAD ASSY 30.1" LED, 5-PIN 200MM H/H 1
1 CON07P200ADN LEAD ASSY 17.1" CONTROL, 7-PIN 420MM 1
1 CON10P100ACF LEAD ASSY 17.1" IPS INVERTER, 10-PIN 150MM 1
1 CON20P125ABL LEAD ASSY 23", Panel, 20 PIN, 200MM 1
1 PANLC171W030 PANEL, LCD COLOR 17.1", 450CD, LC171W03(A3) 1
RL-17S10 SERVICE MANUAL PAGE:27
REPLACEMENT PART LIST
2.Parts List (Main PCB)
LEVEL P/N PART NAME DISPCRIPTION LOCATION NO. Q' TY
0 AYMALT17A01C MAIN PCB ASS' Y LT-17TP, MULTI 1
1 GRLT21BS001H GR, 17.1" YUV SMD 1
2 0TRKE3875STS TRANSISTOR, CHIP KTC3875S Q401,Q402,Q403 3
2 0RHSS750DJTS RESISTOR, CHIP 75 OHM, 1608 J C409,C410 2
2 0RHSS474DJTS RESISTOR, CHIP 470K OHM, 1608 J R445,R446 2
2 0RHSS473DJTS RESISTOR, CHIP 47K OHM, 1608 J R402,R416,R419 3
2 0RHSS333DJTS RESISTOR, CHIP 33K OHM, 1608 J R403,R417,R420 3
2 0RHSS102DJTS RESISTOR, CHIP 1K OHM, 1608 J R404,R418,R421 3
2 0RHSS101DJTS RESISTOR, CHIP 100 OHM, 1608 J R406,R514 2
R424,R425,R540,R541,
2 0RHSS000DJTS RESISTOR, CHIP 0 OHM, 1608 J 6
R542,R546
1 GRLT21BS001F GR, 17.1" LVDS SMD 1
2 WAFYH20125AS WAFER, PIN 20-PIN, P1.25mm ANGLE P01 1
2 1ICNS90C385S IC, LVDS DS90C385 IC02 1
2 0RHSS220DJTS RESISTOR, CHIP 22 OHM, 1608 J R30 1
2 0RHSS000DJTS RESISTOR, CHIP 0 OHM, 1608 J R78,R82 2
2 0LBSS101DJTS BEAD, CHIP 100 OHM, 2012 L03 1
C76,C78,C79,C80,
2 0CHSS104DZTS CAPACITOR, CHIP 0.1UF,1608 5
C81
1 GRLT21BS001D GR, 17.1" MULTI SMD 1
2 1ICMI3410DBS IC, SOUND DECODER MSP3410D IC601 1
2 0RHSS821DJTS RESISTOR, CHIP 820 OHM, 1608 J R553 1
2 0RHSS472DJTS RESISTOR, CHIP 4.7K OHM, 1608 J R136,R137 2
2 0RHSS221DJTS RESISTOR, CHIP 220 OHM, 1608 J R117 1
2 0DHKEC102STS DIODE, CHIP KRC102S Q101,Q102 2
1 GRLT21BS001A GR, 17.1" COMMON SMD 1
2 WAFJS10100AS WAFER, PIN 10-PIN, P1.0mm P803 1
2 1ICSE24C16TS IC, EEPROM 16K IC102,IC203 2
2 0RHSS392DJTS RESISTOR, CHIP 3.9K OHM, 1608 J R609,R610 2
R119,R125,R127,R129,
2 0RHSS332DJTS RESISTOR, CHIP 3.3K OHM, 1608 J R143,R145,R170,R171, 10
R172,R213
2 0RHSS273DJTS RESISTOR, CHIP 27K OHM, 1608 J R18,R606 2
2 0RHSS272DJTS RESISTOR, CHIP 2.7K OHM, 1608 J R196,R197,R533 3
2 0RHSS270DJTS RESISTOR, CHIP 27 OHM, 1608 J R01 1
2 0RHSS223DJTS RESISTOR, CHIP 22K OHM, 1608 J R104,R153,R183 3
2 0RHSS221DJTS RESISTOR, CHIP 220 OHM, 1608 J R181,R182 2
R04,R05,R06,R07,R11,
R13,R14,R140,R141,
R142,R15,R151,R152,
R176,R177,R190,R191,
R192,R20,R203,R206,
2 0RHSS220DJTS RESISTOR, CHIP 22 OHM, 1608 J 40
R207,R21,R211,R214,
R215,R216,R22,R246,
R248,R253,R254,R405,
R516,R517,R518,R519,
R520,R534,R813
2 0RHSS182DJTS RESISTOR, CHIP 1.8K OHM, 1608 J R814 1
2 0RHSS151DJTS RESISTOR, CHIP 150 OHM, 1608 J R557,R630 2
2 0RHSS123DJTS RESISTOR, CHIP 12K OHM, 1608 J R178 1
2 0RHSS122DJTS RESISTOR, CHIP 1.2K OHM, 1608 J R807 1
2 0RHSS112DJTS RESISTOR, CHIP 1.1K OHM, 1608 J R552 1
2 0RHSS105DJTS RESISTOR, CHIP 1M OHM, 1608 J R08,R602 2
2 0RHSS104DJTS RESISTOR, CHIP 100K OHM, 1608 J R149,R806 2
R210,R247,R249,R603,
2 0RHSS103DJTS RESISTOR, CHIP 10K OHM, 1608 J 7
R631,R802,R805
RL-17S10 SERVICE MANUAL PAGE:28
REPLACEMENT PART LIST
3.Parts List (Main PCB)
LEVEL P/N PART NAME DISPCRIPTION LOCATION NO. Q'TY
R109,R115,R154,R155,
R160,R163,R255,R256,
R611,R612,R613,R614,
2 0RHSS102DJTS RESISTOR, CHIP 1K OHM, 1608 J 23
R615,R616,R622,R629,
R632,R633,R661,R662,
R801,R804,R821
R03,R106,R107,R111,
R112,R113,R114,R118,
R122,R124,R126,R128,
R130,R132,R144,R17,
2 0RHSS101DJTS RESISTOR, CHIP 100 OHM, 1608 J R174,R175,R179,R193, 34
R194,R195,R23,R258,
R259,R506,R509,R510,
R511,R526,R601,R607,
R608,R617
2 0RHSS100DJTS RESISTOR, CHIP 10 OHM, 1608 J R260,R532,R605 3
R102,R12,R164,R166,
R201,R205,R209,R212,
2 0RHSS000DJTS RESISTOR, CHIP 0 OHM, 1608 J R430,R501,R502,R505, 17
R507,R508,R808,R812,
R815
LA01,LA02,LA03,LA04,
LA05,LA06,LA07,LA08,
LA09,LA10,LA11,LA12,
2 0LYSS600DJTS INDUCTOR, ARRAY CHIP 60 OHM, 3216 LA13,LA14,LA15,LA16, 25
LA17,LA18,LA19,RA01,
RA02,RA03,RA04,RA05,
RA06
2 0LBSS601KJTS BEAD, CHIP 600 OHM, 3A 3216 L803,L804 2
L04,L05,L06,L07,L106,
2 0LBSS601FJTS BEAD, CHIP 600 OHM, 3216 L209,L210,L601,L602, 11
L603,L604
2 0LBSS260DJTS BEAD, CHIP 26 OHM, 2012 L202 1
L02,L243,L244,L245,
2 0LBSS101DJTS BEAD, CHIP 100 OHM, 2012 L406,L407,L409,L411, 11
L412,L440,L441
2 0ICVI4925DTS IC, MOSFET CHIP SI4925 IC803,IC822 2
2 0ICSS41616BS IC, CMOS SDRAM CHIP 512K*16BIT*2 SDRAM IC03,IC04 2
2 0ICKE78L9FTS IC, REGULATOR CHIP KIA78L09F, 9.0V IC807 1
2 0ICKE78L5FTS IC, REGULATOR CHIP KIA78L05F, 5.0V IC804 1
2 0ICKE7042FTS IC, RESET CHIP KIA7042AF, 4.2V RESET IC603 1
2 0ICKE7027FTS IC, RESET CHIP KIA7027AF, 2.7V RESET IC07,IC103 2
2 0DSSCB340ATS DIODE, SCHOTTKY CHIP B340A, 3A D803 1
D102,D603,D604,D801,
2 0DHKEKDS181S DIODE, CHIP KDS181 5
D805
2 0CHSS683DKTS CAPACITOR, CHIP 0.068UF,1608 C501,C502,C559 3
2 0CHSS620DJTS CAPACITOR, CHIP 62PF,1608 C151,C152 2
2 0CHSS560DJTS CAPACITOR, CHIP 56PF,1608 C424,C604,C605 3
2 0CHSS474DZTS CAPACITOR, CHIP 0.47UF,1608 C800 1
2 0CHSS472DKTS CAPACITOR, CHIP 4700PF,1608 C638 1
C407,C408,C411,C425,
2 0CHSS471DJTS CAPACITOR, CHIP 470PF,1608 7
C426,C441,C442
2 0CHSS470DJTS CAPACITOR, CHIP 47PF,1608 C124,C125 2
C219,C228,C232,C237,
2 0CHSS393DKTS CAPACITOR, CHIP 0.039UF,1608 8
C519,C537,C548,C557
2 0CHSS392DKTS CAPACITOR, CHIP 3900PF,1608 C222 1
2 0CHSS391DJTS CAPACITOR, CHIP 390PF,1608 C521,C540,C550 3
RL-17S10 SERVICE MANUAL PAGE:29
REPLACEMENT PART LIST
4.Parts List (Main PCB)
LEVEL P /N PART NAME D IS P C R IP T IO N L O C A T IO N N O . Q 'T Y
2 0C H S S 332D K TS C A P A C ITO R , C H IP 3300P F,1608 C 623 1
2 0C H S S 331D JTS C A P A C ITO R , C H IP 330P F,1608 C 181,C 182 2
2 0C H S S 330D JTS C A P A C ITO R , C H IP 33PF,1608 C 105,C 106,C 419 3
C 110,C 511,C 512,C 513,
C 514,C 515,C 516,C 523,
2 0C H S S 224D ZTS C A P A C ITO R , C H IP 0.22U F,1608 C 541,C 552,C 626,C 631, 18
C 632,C 633,C 634,C 635,
C 661,C 662
C 528,C 617,C 618,C 627,
2 0C H S S 222D K TS C A P A C ITO R , C H IP 2200P F,1608 C 628,C 629,C 630,C 663, 9
C 664
2 0C H S S 220D JTS C A P A C ITO R , C H IP 22PF,1608 C 524,C 529,C 530 3
2 0C H S S 200D JTS C A P A C ITO R , C H IP 20PF,1608 C 32,C 503 2
C 538,C 539,C 558,C 615,
2 0C H S S 152D K TS C A P A C ITO R , C H IP 1500P F,1608 5
C 616
2 0C H S S 150D JTS C A P A C ITO R , C H IP 15PF,1608 C 39,C 40,C 420 3
C 571,C 572,C 573,C 574,
2 0C H S S 105D ZTS C A P A C ITO R , C H IP 1U F,1608 8
C 575,C 576,C 577,C 578
C 01,C 02,C 03,C 04,C 05,
C 07,C 107,C 114,C 116,
C 118,C 127,C 129,C 131,
C 143,C 145,C 203,C 204,
C 205,C 206,C 207,C 209,
C 210,C 212,C 213,C 214,
C 215,C 216,C 217,C 218,
C 225,C 229,C 230,C 233,
C 234,C 235,C 240,C 243,
2 0C H S S 104D ZTS C A P A C ITO R , C H IP 0.1U F,1608 73
C 33,C 36,C 37,C 38,C 41,
C 42,C 421,C 505,C 506,
C 507,C 508,C 509,C 510,
C 542,C 555,C 614,C 620,
C 624,C 636,C 647,C 651,
C 654,C 67,C 68,C 69,
C 70,C 71,C 72,C 73,
C 74,C 802,C 808,C 811,
C 812,R 809,R 810
C 102,C 103,C 104,C 108,
C 111,C 112,C 113,C 417,
2 0C H S S 103D K TS C A P A C ITO R , C H IP 0.01U F,1608 13
C 418,C 603,C 609,C 612,
C 640
2 0C H S S 102D K TS C A P A C ITO R , C H IP 1000P F,1608 C 223,C 522,C 531,C 551 4
2 0C H S S 101D JTS C A P A C ITO R , C H IP 100P F,1608 C 109,C 404 2
C 242,C 43,C 44,C 45,
C 46,C 47,C 48,C 49,C 50,
C 51,C 52,C 53,C 54,C 55,
2 0C H S S 100D JTS C A P A C ITO R , C H IP 10PF,1608 25
C 56,C 57,C 58,C 59,C 60,
C 61,C 62,C 63,C 64,C 65,
C 66
2 0C H S S 080D C TS C A P A C ITO R , C H IP 8P F,1608 C 403,C 423 2
2 0C H S S 030D C TS C A P A C ITO R , C H IP 3P F,1608 C 208,C 553,C 554 3
2 0C H S S 020D C TS C A P A C ITO R , C H IP 2P F,1608 C 607,C 608 2
2 1IC R O 6161FTS IC , R E G U LA TO R B A 6161F IC 802 1
2 1IC R O 033FP TS IC , R E G U LA TO R 3.3V 1A , B A 033FP IC 104,IC 806 2
2 1IC P H 74F08TS IC , A N D G A TE 74F08 IC 202 1
2 1IC M I3230D B S IC , VID EO D EC O D ER VPC 3230D IC 501 1
2 1IC A D 9883A B S IC , A /D C O N VER TER A D 9883A -110M H Z IC 201 1
2 1IC 88L284A B S IC , S C A LER M X88L284- A E C IC 01 1
RL-17S10 SERVICE MANUAL PAGE:30
REPLACEMENT PART LIST
5.Parts List (Main PCB)
LEVEL P/N PART NAME DISPCRIPTION LOCATION NO. Q'TY
ZD240,ZD241,ZD242,
ZD243,ZD244,ZD245,
ZD246,ZD402,ZD403,
2 1DZSC5231BTS DIODE, ZENER CHIP 5.1V 17
ZD404,ZD409,ZD410,
ZD411,ZD412,ZD413,
ZD414,ZD415
2 111-A40A PCB, MAIN SEVIT 17.1" MAIN 1
Q103,Q104,Q111,Q301
,
2 0TRKE3875STS TRANSISTOR, CHIP KTC3875S 9
Q302,Q505,Q801,Q802
2 0TRKE1504STS TRANSISTOR, CHIP KTA1504S Q601,Q602,Q604 3
R243,R244,R245,R408
2 0RHSS750DJTS RESISTOR, CHIP 75 OHM, 1608 J , 8
R431 R432 R434 R512
2 0RHSS683DJTS RESISTOR, CHIP 68K OHM, 1608 J R628 1
2 0RHSS680DJTS RESISTOR, CHIP 68 OHM, 1608 J R156 1
2 0RHSS562DJTS RESISTOR, CHIP 5.6K OHM, 1608 J R131 1
2 0RHSS561DJTS RESISTOR, CHIP 560 OHM, 1608 J R620,R627 2
2 0RHSS513DJTS RESISTOR, CHIP 51K OHM, 1608 J R423 1
R426,R427,R435,R437
2 0RHSS512DJTS RESISTOR, CHIP 5.1K OHM, 1608 J , 6
R443 R444
2 0RHSS474DJTS RESISTOR, CHIP 470K OHM, 1608 J R436,R438,R441,R442 4
R146,R147,R19,R167,
R168,R250,R251,R252
2 0RHSS472DJTS RESISTOR, CHIP 4.7K OHM, 1608 J , 16
R515,R618,R619,R625
R110,R134,R135,R407
2 0RHSS471DJTS RESISTOR, CHIP 470 OHM, 1608 J , 5
R433
2 0RHSS470DJTS RESISTOR, CHIP 47 OHM, 1608 J R138,R139 2
2 0RHSS433DJTS RESISTOR, CHIP 43K OHM, 1608 J R116 1
2 0RHSS3R3DJTS RESISTOR, CHIP 3.3 OHM, 1608 J R623,R624 2
2 0RHSS393DJTS RESISTOR, CHIP 39K OHM, 1608 J R422 1
1 GRLT21BM001G GR, 17.1" MULTI MANUAL