Text preview for : Tda3653b.pdf part of Philips TDA3653b Philips Quality Data Sheet
Back to : Tda3653b.pdf | Home
INTEGRATED CIRCUITS
DATA SHEET
TDA3653B TDA3653C Vertical deflection and guard circuit (90°)
Product specification File under Integrated Circuits, IC02 March 1991
Philips Semiconductors
Product specification
Vertical deflection and guard circuit (90°)
GENERAL DESCRIPTION
TDA3653B TDA3653C
The TDA3653B/C is a vertical deflection output circuit for drive of various deflection systems with currents up to 1.5 A peak-to-peak. Features · Driver · Output stage · Thermal protection and output stage protection · Flyback generator · Voltage stabilizer · Guard circuit QUICK REFERENCE DATA PARAMETER Supply (note 1) Supply voltage range pin 9 pin 6 Output (pin 5) Peak output voltage during flyback Output current Operating junction temperature range Thermal resistance junction to mounting base (SOT110B) (SOT131) Note to the quick reference data 1. The maximum supply voltage should be chosen such that during flyback the voltage at pin 5 does not exceed 60 V. PACKAGE OUTLINES TDA3653B: 9-lead SIL; plastic (SOT110B); SOT110-1; 1996 November 25. TDA3653C: 9-lead SIL; plastic power (SOT131); SOT131-2 November 25. Rth j-mb Rth j-mb - - 10 3.5 - - K/W K/W V5-4M I5(p-p) Tj - - -25 - 1.2 - 60 1.5 +150 V A °C VP = V9-4 V6-4 10 - - - 40 60 V V SYMBOL MIN. TYP. MAX. UNIT
March 1991
2
Philips Semiconductors
Product specification
Vertical deflection and guard circuit (90°)
TDA3653B TDA3653C
Fig.1 Block diagram.
March 1991
3
Philips Semiconductors
Product specification
Vertical deflection and guard circuit (90°)
FUNCTIONAL DESCRIPTION Output stage and protection circuit
TDA3653B TDA3653C
Pin 5 is the output pin. The supply for the output stage is fed to pin 6 and the output stage ground is connected to pin 4. The output transistors of the class-B output stage can each deliver 0.75 A maximum. The maximum voltage for pin 5 and 6 is 60 V. The output power transistors are protected such that their operation remains within the SOAR area. This is achieved by the co-operation of the thermal protection circuit, the current-voltage detector, the short-circuit protection and the special measures in the internal circuit layout. Driver and switching circuit Pin 1 is the input for the driver of the output stage. The signal at pin 1 is also applied via external resistors to pin 3 which is the input of a switching circuit. When the flyback starts, this switching circuit rapidly turns off the lower output stage and so limits the turn-off dissipation. It also allows a quick start of the flyback generator. External connection of pin 1 to pin 3 allows for applications in which the pins are driven separately. Flyback generator During scan the capacitor connected between pins 6 and 8 is charged to a level which is dependent on the value of the resistor at pin 8 (see Fig.1). When the flyback starts and the voltage at the output pin (pin 5) exceeds the supply voltage, the flyback generator is activated. The supply voltage is then connected in series, via pin 8, with the voltage across the capacitor during the flyback period. This implies that during scan the supply voltage can be reduced to the required scan voltage plus saturation voltage of the output transistors. The amplitude of the flyback voltage can be chosen by changing the value of the external resistor at pin 8. It should be noted that the application is chosen such that the lowest voltage at pin 8 is > 2.5 V, during normal operation. Guard circuit When there is no deflection current and the flyback generator is not activated, the voltage at pin 8 reduces to less than 1.8 V. The guard circuit will then produce a DC voltage at pin 7, which can be used to blank the picture tube and thus prevent screen damage. Voltage stabilizer The internal voltage stabilizer provides a stabilized supply of 6 V to drive the output stage, which prevents the drive current of the output stage being affected by supply voltage variations.
March 1991
4
Philips Semiconductors
Product specification
Vertical deflection and guard circuit (90°)
RATINGS Limiting values in accordance with the Absolute Maximum System (IEC 134); pins 4 and 2 externally connected to ground. PARAMETER Supply voltage (pin 9) Supply voltage output stage (pin 6) Output voltage (pin 5) Input voltage (pins 1 and 3) External voltage at pin 7 Peak output current (pin 5) repetitive non-repetitive Peak output current (pin 8) repetitive non-repetitive Total power dissipation Storage temperature range Operating ambient temperature range Operating junction temperature range Note 1. Non-repetitive duty factor maximum 3.3%. I8RM ± I8SM Ptot Tstg Tamb Tj -25 -55 0.85 - 0.75 1.5 see Fig.2 +150 see Fig.2 +150 ± I5RM ± I5SM - - 0.75 1.5 SYMBOL VP = V9-4 V6-4 V5-4 V1; 3-2 V7-2 - - - - - MIN. 40 60 60 VP 5.8 MAX.
TDA3653B TDA3653C
UNIT V V V V V A A(1) A A(1) °C °C
Fig.2 Power derating curves (for SOT110B).
Fig.3 Quiescent current I4 as a function of supply voltage VP.
March 1991
5
Philips Semiconductors
Product specification
Vertical deflection and guard circuit (90°)
TDA3653B TDA3653C
CHARACTERISTICS VP = V9-4 = 26 V; Tamb = 25 °C; pins 2 and 4 externally connected to ground; unless otherwise specified PARAMETER Supply Supply voltage (pin 9) Supply voltage (pin 6) Total supply current (pin 6 and pin 9) Quiescent current (pin 4) Variation of quiescent current with temperature Output current Output current (pin 5) (peak-to-peak value) Output current flyback generator (pin 8) Output current flyback generator (pin 8) Output voltage Peak voltage during flyback Saturation voltage to supply at -I5 = 0.75 A at I5 = 0.75 A at -I5 = 0.60 A at I5 = 0.60 A Saturation voltage to ground at I5 = 0.75 A at I5 = 0.60 A Flyback generator Saturation voltage at -I8 = 0.85 A at I8 = 0.75 A at -I8 = 0.70 A at I8 = 0.60 A Flyback generator active if: Leakage current at pin 8 Input Input current (pin 1) Input voltage during scan (pin 1) Input voltage during scan (pin 3) pins 1 and 3 not connected March 1991 6 V3-2 0.8 - VP V I5 = 0.75 A I5 = 0.75 A I1 V1-2 - - 0.33 1.5 0.55 2.4 mA V note 3 note 3 V9-8sat V8-9sat V9-8sat V8-9sat V5-9 -I8 - - - - 4.0 - 1.6 2.3 1.4 2.2 - 5.0 2.1 2.8 1.9 2.7 - 100 V V V V V µA V5-4sat V5-4sat - - 2.3 2.1 2.7 2.4 V V note 3 note 3 V6-5sat V5-6sat V6-5sat V5-6sat - - - - 2.5 2.5 2.2 2.3 3.0 3.0 2.7 2.8 V V V V V5-4M - - 60 V I8 - 0.6 0.75 A -I8 - 0.7 0.85 A I5(p-p) - 1.2 1.5 A I4 - -0.04 - mA/K note 2 see Fig.3 IP = I6 + I9 I4 34 25 50 40 85 65 mA mA note 1 note 1 VP = V9-4 V6-4 10 - - - 40 60 V V CONDITIONS SYMBOL MIN. TYP. MAX. UNIT
Philips Semiconductors
Product specification
Vertical deflection and guard circuit (90°)
TDA3653B TDA3653C
MIN. 0.03 - 3.9 - - - - 5.3 - - TYP. - 0.21 6.7 250 250 MAX. UNIT mA mA k mV mV
PARAMETER Input current during scan (pin 3) pins 1 and 3 not connected pins 1 and 3 connected Input resistance (pin 3) Input voltage during flyback (pin 1) Input voltage during flyback (pin 3) Guard circuit Output voltage (pin 7) loaded with 100 k loaded with 0.5 mA Internal series resistance of pin 7 Guard circuit active if V8-2 is lower than General data Thermal protection becomes active if junction temperature exceeds Thermal resistance junction to mounting base Open loop gain at 1 kHz Frequency response (-3 dB) Notes to the characteristics
CONDITIONS I3 I3 R3
SYMBOL
V1-2 V3-2 note 4 V7-2 V7-2 Ri7 note 5 V8-2
4.4 3.6 0.95 -
5.1 4.4 1.35 -
5.8 5.3 1.7 1.8
V V k V
Tj Rth j-mb note 6 note 7 GoI f
158 - - -
175 10 42 40
192 12 - -
°C K/W dB kHz
1. The maximum supply voltage should be chosen such that during flyback the voltage at pin 5 does not exceed 60 V. 2. When V5-4 = 13 V and no load at pin 5. 3. Duty factor maximum 3.3%. 4. Guard circuit is active. 5. During normal operation the voltage V8-2 may not be lower than 2.5 V. 6. Rload = 8 ; Iload(rms) = 125 mA. 7. With 220 pF between pins 1 and 5.
March 1991
7
Philips Semiconductors
Product specification
Vertical deflection and guard circuit (90°)
APPLICATION INFORMATION
TDA3653B TDA3653C
Note to deflection coils AT1236/20: L = 29 mH, R = 13.6 ; deflection current without overscan is 0.82 A peak-to-peak and EHT voltage is 25 kV.
Fig.4
Typical application circuit diagram of the TDA3653B/C (vertical output), when used in combination with the TDA2578A (see Fig.5).
March 1991
8
Philips Semiconductors
Product specification
Vertical deflection and guard circuit (90°)
TDA3653B TDA3653C
Fig.5 Typical application circuit diagram; for combination of the TDA2578A with the TDA3653B/C (see Fig.4).
March 1991
9
March 1991
Philips Semiconductors
Vertical deflection and guard circuit (90°)
10
(1) Dependent on PCB layout.
Product specification
TDA3653B TDA3653C
Fig.6 Application circuit diagram for combination with TDA2579A for 90° picture tube.
Philips Semiconductors
Product specification
Vertical deflection and guard circuit (90°)
PACKAGE OUTLINES SIL9MPF: plastic single in-line medium power package with fin; 9 leads
TDA3653B TDA3653C
SOT110-1
D
D1 q P P1 A2
A3 q1 q2
A A4 seating plane E pin 1 index
L 1 Z b2 e b b1 w M 9 Q
c
0
5 scale
10 mm
DIMENSIONS (mm are the original dimensions) UNIT mm A 18.5 17.8 A2 max. 3.7 A3 8.7 8.0 A4 15.8 15.4 b 1.40 1.14 b1 0.67 0.50 b2 1.40 1.14 c 0.48 0.38 D (1) 21.8 21.4 D1 21.4 20.7 E (1) 6.48 6.20 e 2.54 L 3.9 3.4 P 2.75 2.50 P1 3.4 3.2 Q 1.75 1.55 q 15.1 14.9 q1 4.4 4.2 q2 5.9 5.7 w 0.25 Z (1) max. 1.0
Note 1. Plastic or metal protrusions of 0.25 mm maximum per side are not included. OUTLINE VERSION SOT110-1 REFERENCES IEC JEDEC EIAJ EUROPEAN PROJECTION
ISSUE DATE 92-11-17 95-02-25
March 1991
11
Philips Semiconductors
Product specification
Vertical deflection and guard circuit (90°)
TDA3653B TDA3653C
SIL9P: plastic single in-line power package; 9 leads
SOT131-2
non-concave x Dh
D Eh
view B: mounting base side d A2
B seating plane j E
A1 b
L
c 1 Z e bp w M 0 5 scale DIMENSIONS (mm are the original dimensions) UNIT mm A1 max. 2.0 A2 4.6 4.2 b max. 1.1 bp 0.75 0.60 c 0.48 0.38 D (1) 24.0 23.6 d 20.0 19.6 Dh 10 E (1) 12.2 11.8 e 2.54 Eh 6 j 3.4 3.1 L 17.2 16.5 Q 2.1 1.8 w 0.25 x 0.03 Z (1) 2.00 1.45 10 mm 9 Q
Note 1. Plastic or metal protrusions of 0.25 mm maximum per side are not included. OUTLINE VERSION SOT131-2 REFERENCES IEC JEDEC EIAJ EUROPEAN PROJECTION
ISSUE DATE 92-11-17 95-03-11
March 1991
12
Philips Semiconductors
Product specification
Vertical deflection and guard circuit (90°)
SOLDERING Introduction There is no soldering method that is ideal for all IC packages. Wave soldering is often preferred when through-hole and surface mounted components are mixed on one printed-circuit board. However, wave soldering is not always suitable for surface mounted ICs, or for printed-circuits with high population densities. In these situations reflow soldering is often used. This text gives a very brief insight to a complex technology. A more in-depth account of soldering ICs can be found in our "IC Package Databook" (order code 9398 652 90011). Soldering by dipping or by wave The maximum permissible temperature of the solder is 260 °C; solder at this temperature must not be in contact with the joint for more than 5 seconds. The total contact time of successive solder waves must not exceed 5 seconds. DEFINITIONS Data sheet status Objective specification Preliminary specification Product specification Limiting values
TDA3653B TDA3653C
The device may be mounted up to the seating plane, but the temperature of the plastic body must not exceed the specified maximum storage temperature (Tstg max). If the printed-circuit board has been pre-heated, forced cooling may be necessary immediately after soldering to keep the temperature within the permissible limit. Repairing soldered joints Apply a low voltage soldering iron (less than 24 V) to the lead(s) of the package, below the seating plane or not more than 2 mm above it. If the temperature of the soldering iron bit is less than 300 °C it may remain in contact for up to 10 seconds. If the bit temperature is between 300 and 400 °C, contact may be up to 5 seconds.
This data sheet contains target or goal specifications for product development. This data sheet contains preliminary data; supplementary data may be published later. This data sheet contains final product specifications.
Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information Where application information is given, it is advisory and does not form part of the specification. LIFE SUPPORT APPLICATIONS These products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips for any damages resulting from such improper use or sale.
March 1991
13