Text preview for : Philips 15MF605T-17, 20MF605T-17 (Chassis F1) (Service Manual).pdf part of Philips 15MF605T/17, 20MF605T/17 Service manual for the LCD TV sets Philips 15MF605T/17, 20MF605T/17 (Chassis F1).
Back to : Philips 15MF605T-17, 20MF | Home
F1 LCD Monitor/TV
F1-15" F1-20"
Service Service Service
15MF605T/17 20MF605T/17
Horizontal frequencies F1-15"30 - 49kHz F1-20"30 - 40KHz
TABLE OF CONTENTS
Description Page Important Safety Notice------------------------------- 2 Technical Data/Installation------------------------3~8 On-Screen Display/Aging Mode------------------9~11 Warning message/Factory Mode----------------12~13 Trouble shooting--------------------------------------14 Failure Mode Of Panel/Wiring Diagram---------15~16 Mechanical/Electrical Instructions-------------17~22 Display adjustment-------------------------------23~24 DDC DATA/Instructions--------------------------25~32 ISP Instructions----------------------------------33~34 Block /DC/DC POWER Diagram-----------------35~36 PC-IN/SCART Diagram---------------------------37~38 VIDEO-IN/VIDEO DECODER Diagram----------39~40 Description Page T/T DECODER Diagram------------------------------41 MCU/Scaler Diagram----------------------------42~43 SRAM/Panel Interface Diagram----------------44~45 Sound DECODER/Audio Diagram--------------46~47 Scaler Board C.B.A------------------------------48~49 Key And IR Diagram/C.B.A---------------------50~51 YPbPr-IN/Inverter Diagram/C.B.A-------------52~56 Exploded View--------------------------------------- 57 Recommended/Spare/Different parts list----58~62 Repair Tips/Repair Flow Chart-----------------63~66 General product specification------------------67~90 Circuit description-------------------------------90~91 Safety Test Requirements---------------------------92
SAFETY NOTICE
ANY PERSON ATTEMPTING TO SERVICE THIS CHASSIS MUST FAMILIARIZE HIMSELF WITH THE CHASSIS AND BE AWARE OF THE NECESSARY SAFETY PRECAUTIONS TO BE USED WHEN SERVICING ELECTRONIC EQUIPMENT CONTAINING HIGH VOLTAGES.
CAUTION: USE A SEPARATE ISOLATION TRANSFORMER FOR THIS UNIT WHEN SERVICING.
REFER TO BACK COVER FOR IMPORTANT SAFETY GUIDELINES
Published by BCU Monitors
Printed in suzhou
Copyright reserved
Subject to modification F Jan . 21 2005
GB
3138 106 10444
2
Magnavox LCD TV Go to cover page
Important Safety Notice
FOR PRODUCTS CONTAINING LASER : DANGERInvisible laser radiation when open. AVOID DIRECT EXPOSURE TO BEAM. CAUTIONUse of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. CAUTIONThe use of optical instruments with this product will increase eye hazard.
Proper service and repair isimportant to the safe, reliable operation of all HPConsumer Electronics Company** Equipment. The service procedures recommended by HP and described in this service manual are effective methods of performing service operations. Some ofthese service operations require the use of tools specially designed for the purpose. The special tools should be used when and as recommended. It is important to note that this manual contains various CAUTIONS and NOTICES which should be carefully read in order to minimize the risk of personal injury to service personnel. The possibility exists that improper service methods may damage the equipment. It is also important to understand that these CAUTIONS and NOTICES ARE NOT EXHAUSTIVE. HP could not possibly know, evaluate and advise the service trade of all conceivable ways in which service might be done or of the possible hazardous consequences of each way. Consequently, HP has not undertaken any such broad evaluation. Accordingly, a servicer who uses a service procedure or tool which is not recommended by HP must first satisfy himself thoroughly that neither his safety nor the safe operation of the equipment will be jeopardized by the service method selected. * * Hereafter throughout this manual, HP Consumer Electronics Company will bereferred to as HP.
WARNING
TO ENSURE THE CONTINUED RELIABILITY OF THIS PRODUCT, USE ONLY ORIGINAL MANUFACTURER'S REPLACEMENT PARTS, WHICH ARE LISTED WITH THEIR PART NUMBERS IN THE PARTS LIST SECTION OF THIS SERVICE MANUAL.
Take care during handling the LCD module with backlight unit - Must mount the moduleusing mounting holes arranged infour corners. - Do not press onthe panel, edge of theframe strongly or electric
Critical components having special safety characteristics are identified with a bythe Ref. No. inthe parts list and enclosed within a broken line* (where several critical components are grouped in one area) along with the safety symbol on the schematics or exploded views. Use of substitute replacement parts which do not have the same specified safety characteristics may create shock, fire, or other hazards. Under no circumstances should the original design be modified or altered without written permission from Philips. Philips assumes no liability, express or implied, arising out of any unauthorized modification of design. Servicer assumes all liability. * Broken Line
shock as this will result in damage to the screen. - Do not scratch orpress on the panel withany sharp objects, such as pencil or pen asthis may result in damage to the panel. - Protect the module fromthe ESD as it maydamage the electronic circuit (C-MOS). - Make certain that treatment person s body are grounded through wrist band. - Do not leave themodule in high temperature andin areas of high humidity for a long time. - Avoid contact with water as it may ashort circuit within the module. - If the surface ofpanel become dirty, please wipe it off with a soft material. (Cleaning with a dirty or rough cloth may damage the panel.)
Technical Data(15MF605T/17)
1. General 1.1. Product description This 15 LCD Monitor/TV is specified as a display peripheral with analog video signal input and include TV function with 15 TFT LCD display. Horizontal scan range is 30 -49KHz and refresh range is65 - 62Hz. This scan range allows it to display resolution up to1024*768 non-interlaced at60 Hz efresh rate. The image can be adjust through OSD control, these adjustments can be stored on a board memory Including 11 factory pre - load modes. 1.2. Basic data 1.2.1. LCD 1.2.1.1 LPL panel Type NR. : LC150X02 Display area(mm) : 304.128(H) x 228.096(V) (15.0- inch diagonal) Number of Pixels : 1024(H) x 768(V) Pitch ( mm ) : 0.297(H)x 0.297(V) Color pixel arrangement : RGB vertical stripes Display operatingmode : Transmissive mode,normally white Color depth : 16M colors( 6 bits with FRC) Brightness (cd/m^2) : 450(cd/m^2)(Center 1 points Typ.) Viewing angle (CR>10) : -65 ~ 65 (H), -55 ~ 45 (V)(Typ.) Surface treatment :Hard coating(3H) &Anti-glare (Haze 13%) Electrical interface : LVDS (1 pixel/clock) Response Time : 16ms(typ.) (Tr+Tf ) Power Consumption (W) : 16.9(typ.) Contrast ratio : Typical 400 : 1 Module size (mm) : 332.8(W) x 262.8(H) x 18.0(D) Module weight (g) : 1750 Backlight : 4 CCFL 1.2.1.2.AUO panel Type NR. : T150XG01 Display area(mm): 304. 128(H) x 228.096(V) (15.0- inch diagonal) Number of Pixels : 1024(H) x 768(V) Pitch ( mm ) : 0.297(H) x 0.297(V) Color pixel arrangement : RGB vertical stripes Display operatingmode : TN mode, normally white Color depth : 16M colors( 6 bits with FRC) Brightness (cd/m^2) : 450 nit (typ. ) @ 6.0mA Viewing angle (CR>10) : -70 ~ 70 (H), -60 ~ 60 (V)(Typ.) Surface treatment :Hard coating(3H) &AG Electrical interface :1ch LVDS (8bit) Response Time : 16ms(typ.) (Tr+Tf) Power Consumption(W) : 22 (typ.)@ 6.0mA Contrast ratio : Typical 450 : 1 Module size (mm) : 32 6.5(W) x 253.5(H) x 14.4(D) (typ.) Module weight (g) : 1350 Backlight : 4 CCFL 1.2.1.3.CPT panel Type NR. : CLAA150XP03 Display area(mm) :30.41(H) x 228.1(V) (15.0-inch diagonal) . Number of Pixels : 1024(H) x 768(V) Pitch ( mm ) : 0.297(H) x 0.297(V) Color pixel arra ngement : RGB vertical stripe Display operatingmode : Normally white TN , Color depth : 16.2M colors( 6 bits with FRC) Brightness (cd/m^2) : 400nit(typ.) (center, 6.5mA) Viewing angle (CR>10) : -70 ~ 70 (H), -60 ~ 65 (V)(Typ.) Surface treatment :Anti-glare Wide viewing angle technology : Optical Compensation Film Response Time : 16ms(typ.) Power Consumption(W) :17.1 (typ.) Contrast ratio : Typical 500 : 1 Module size (mm) : 32 6.5(W) x 253.5(H) x 14.0(D) (typ.) Module weight (g) : 1300 Backlight : CCFL, 4 tables, edge -light (top/bottom) 1.2.2. Power supply AC/DC Power adapter: +16V DC/3.75A (100V~240V) Power consumption: 40 W (typical) Power cord length and type: 1.8M, USA type Power indicator : LED (On:Green ,Sleeping mode Amber ) : Auto power saving : EPA 1.2.3. Horizontal scan : 30- 49KHz 1.2.4. Vertical scan : 56 - 62 Hz
Magnavox LCD TV
3
Go to cover page
1.2.5. Input signals 1.PC Signal type Analog Video: 0.7 Vp Linear , positive polarity -p Sync : TTL level , separate , positive or negative polarity 2.TV signal type RF signal : Aerial input Video signal : S -video input CVBS YPbPr 3.Audio signal : S -video L/R ,YPbPr L/R audio input PC line in 1.2.6 Input connectors (1) Input analog D -sub connector pin assignme nt:
Sync polarity : -Hori.sync -Vert.sync
positive/negative positive/negative
4
Magnavox LCD TV Go to cover page
1. General 1.1. Product description This 20 " LCD Monitor/TV is specified as a display peripheral with analog video signal input and include TV function with 20 " TFT LCD display. Horizontal scan range is 30-40K Hz and refresh rate 56-62Hz. This scan range allows it to display resolution up to 800*600 non-interlaced at 60 Hz refresh rate. The image can be adjust through OSD control, these adjustments can be stored on a board memory including 8 factory pre-load modes. 1.2. Basic data 1.2.1 LCD panel Type NR. :A201SN02 (AUO) Display area(mm) : 408(H) x 306(V) (20.1-inch diagonal) Display mode : TN type, Normal white + SWV film Number of Pixels : 800(H) x 600(V) Pitch ( mm ) : 0.51(H) x 0.51(V) Color pixel arrangement : RGB vertical stripes Display mode : normally white TN Number of color : 16.7M ( 8 bits) Brightness (cd/m^2) : 450nit(typ.) Viewing angle : -80 ~ 80 (H), -60 ~ 60 (V)(Typ.) Response time : 16ms typ. (Tr+Tf) Surface treatment : Hard Coating + AR Electrical interface : TTL (1 port) Total module power(W) : 35W(typ.) Contrast ratio : Typical 500 : 1 Overall dimension (mm) : 448(W) x 347(H) x 23(D)(max.) Module weight (g) : 3500 Backlight : 6 CCFL **Income inspection, please refer to panel specification.** 1.2.2. Power supply Power consumption : Operating 55 W (typical) Power cord length : 1.8M Power cord type : USA type Power indicator : LED (On: Green ,Sleeping mode: Amber ) Auto power saving : EPA 1.2.3. Horizontal scan : 30 - 40KHz 1.2.4. Vertical scan : 56 - 62 Hz 1.2.5. Input signals 1.PC Signal type Analog Video: 0.7 Vp-p Linear , positive polarity Sync : TTL level , separate , positive or negative polarity 2.TV signal type RF signal : Aerial input
Sync polarity
: -Hori.sync positive/negative -Vert.sync positive/negative
Video signal : S -video input CVBS Y PbPr
3.Audio signal : S -video L/R ,YPbPr L/R audio input PC line in
1.2.6
Input connectors
(1) Input analog D-sub connector pin assignment:
Installation
Before installation Before proceed to install your new LCD TV ,please follow the steps and diagrams as shownto familiarize yourself with the correct and safe way of unfolding the base. 1.Place the set facing down on a fl at surface and aprotective sheet. 2.Unfold the base f llowing the direction as shown on the diagram. o 3.Place the set upright, you LCD TV is now ready for install.
Magnavox LCD TV
5
Go to cover page
INSTALLING LCD TV ON THE WALL The stand of your LCD TV is comply with Standard VESA 75 standard, if you intend to install the LCD TV on the wall, please consult a professional technician for proper installing.The manufacture accepts no liability for installations not performed by p rofessional technician.
Television and remote control
1.
Plug the DC adapter into the DC IN 16V jack on the LCD TV. Plug the power cableinto an outlet.
2. 3.
Press POWER to turn on the LCD TV. Press VOLUME + to increase the sound level. Or, press VOLUME to lower thesound level.
4. 5.
Press CH+ or CH to select channels. Point the remote control toward on the front of the LCD TV when operating the LCD TV with the remote.
Battery installation
6. Remove the battery compartment lid on the back of the remote. 7. Place two AAA batteries in the remote. Be sure the (+) and ( -) ends of thebatteries line up as marked inside the battery compartment. 8. Reattach the battery compartment lid.
6
Magnavox LCD TV Go to cover page
Installation
ANTENNA CONNECTION Acombination antenna receives normal broadcast channels (VHF 2 13 and UHF 14 69). Your connection is easy because there is only one 75 (ohm) antenna jack on the back of your TV, and that s where the antenna goes.
1.Power : Power On/Standby 2.Numerica keys : (0~9) ,Channel setting 3.Mute : Sound mute function 4.Prev-CH : Recall previous CH 5.Menu : Main menu select and OK key 6.VOL: Left/Volume Down 7.OK : OK 8.Source : Source select for PC,Tuner,CVBS,S-video,HD 9.Closed cap. : Closed caption on/off 10.SAP(2nd audio) : Sound select 11.CH: Down/Channel Down 12.PIP : PIP size select (Small/Medium/Large/PBP) 13.VOL+ : Right/Volume Up 14.CH+ : Up/ Channel Up 15.Display Format : Select display format (4:3, Expand 4:3, Compress 16:9) 16.Smart Sound : Select sound effect (Personal/News/Music/Theatre) 17.Smart Picture : Select picture effect (Personal/Movie/Sports/ weak signal/multimedia/Night) 18.Sleep Timer : Sleep timer 15,30,60,120,180,240 OFF
1 2
18
17
BASIC CABLE TV CONNECTION Your Cable TV signal into your home may be a single, 75 (ohm) cable. If so, this connection is very simple. Follow the step below to connect your Cable TV signal to your new LCD TV. 1.Connect the Cable TV signal to one end of the supplied L-Adapter as shown, and connect the other end of the adapter to the TV jack on the LCD TV.
3 16
5 15
6 13 8
4
12 7
9
11 14
10
CABLE BOX CONNECTIONS If you have a Cable Box, follow either set of these steps to complete your connections. Cable Box with RF In/Out Jacks This connection will not supply Stereo sound to the LCD TV. 1.Connect the Cable TV signal to the IN jack (or RF IN or CABLE IN) on the Cable Box. 2.Connect an RF coaxial cable (not supplied) to the OUT jack (or TO TV or RF OUT) of the Cable Box. 3.Connect the other end of the coaxial cable to one end of the supplied L-Adapter as shown, and connect the other end of the adapter to the TV jack on the LCD TV. 4.Plug the DC adapter into the DC IN 16V jack on the LCD TV. Plug the power cable into an outlet. 5.Set the Channel 3/4 (or Output channel) switch of the Cable Box to 3 or 4. Set the TV to the same channel. When watching TV programming, change channels at the Cable Box, not the LCD TV.
Installation
Magnavox LCD TV
7
Go to cover page
AUDIO/VIDEO INPUT CONNECTIONS The AUDIO and VIDEO In jacks on the rear of the LCD TV enable quick connections of other equipment. Connect a VCR, DVD Player, Video Game, Camcorder, tc., to these jacks. To view the e material playing on the other equipment, Set the LCD TV to its AV Mode. 1. Connect a RCA-style video cable(usually yellowor marked CVBS) To the VIDEO OUT jacks of the other equipment (DVD Player, Camcorder,etc.) and to the yellow VIDEO jack on the side of the LCD TV. 2. Connect RCA -style audio cables (usuallyred and white) to the AUDIO OUT (leftand right) jacks on the other equipment. Connect the other end of the cables to the AUDIO jack on the side of the LCD TV. 3.Plug the DC Adapter into the DC IN 16V jack on the TV. Plug the power cable into an outlet. Turn on the TV and other quipment. e 4.Press the Source button to set the TV to AV Mode. 5.Press PLAY on the other equipment to view its material on the TV.
Cable Box with Audio/Video Out Jacks This connection will supply Stereo sound to theLCD TV. 1. Connect the Cable TV signal to the IN jack (or RF IN or CABLE IN) on the Cable Box. 2. Using an RCA -type video cable (not supplied) connect one end of the Video cable to the Video Out jack of the Cable Box. Connect the other end of the cable tothe yellow VIDEO jack on the side of the TV. Video cablesare usually marked with yellow and are available from Magnavox orelectronics retailers. Video jacks on most equipment are yellow. 3. Using RCA-type, stereo audio cables (not supplied), connect one end of the cablesto the left and right Audio Out jacks of the Cable Box. Connect the other end of that able to the Audio jack on the side of the c LCD TV. Audio cables ar usually markedwith red and white and are e .The right audio jack is available fromMagnavox or electronics retailers red and the left audio jack is white. Match the cable colors to the jack colors. 4. Plug the DC adapter into the DC IN 16V jack on the LCD TV. Plug the power cableinto an outlet.
The S-Video connection on the rear of the LCD TV can provide you with better LCD picture detail and clarity for the playbackof accessory sources such as DBS (digital broadcast satellite), DVD (digital video discs), video games, and VHS VCR (video casse tte recorder) tapes than the normal antenna picture connections. Note: The accessory device must have an S-VIDEO OUT (put) jack in order for you to complete the connection on this page. 1. Connect an S-Video cable to the S - VIDEO jack of the other equipment(DVD Player,Camcorder, etc.) and to the S - VIDEO jack on the rear of the LCD TV. 2. Connect RCA -style audio cables (usually red and white) to the AUDIO OUT (left and right) jacks on the other equipment.Connect the other end of the cables to the AUDIO jack on the side of the LCD TV. 3.Plug the DC Adapter into the DC IN 16V jack on the LCD TV. Plug the power cableinto an outlet. Turn on the LCD TV and other equipment. 4.Press the Source button to set he LCD TV to its S t -VIDEO mode. 5.Press PLAY on the other equipment toview its material on the LCD TV.
8
Magnavox LCD TV Go to cover page
Installation
PC (MONITOR) CONNECTION This LCD TV can be used as a PC . Your computer will have to be Equipped with a VGA type video output and VGA cable. 1. Connect one end of the VGA Video cable (not supplied) to the Monitor(video) output on the computer, while connecting the other ends to the VGA INPUT jack on the LCD TV. 2. Although audio connections are not required, the LCD TV can Reproduce the computers audio out by an AUDIO ADAPTER to the Audio output jack on the computer (if available) while connecting the other ends of the Audio cables to the PC AUDIO Jacks on the bottom of the TV. 3.Plug the DC Adapter into the DC IN 16V jack on the LCD TV. Plug the power cable into an outlet. Turn on the LCD TV and PC. 4.Press the SOURCE button until PC MODE appears on the screen.
COMPONENT (YPBPR) CONNECTIONS Component Video input provide the highest possible color and picture resolution in the playback of digital signal source material, such as with DVD players. Note: The accessory device must have an component(YPbPr) output jack in order for you to complete the connection on this page. 1. Connect the component (Y, Pb, Pr) Video OUT jacks from the DVD player(or similar device) to the COMP(onent) VIDEO Input jacks on the bottom of the LCD TV. 2.Connect the red and white AUDIO CABLES to the Audio (left ad right) output jacks on the rear of the accessory device to the AUDIO IN jack. Connect the other end of the cable to the Audio jack on the rear of LCD TV. 3. Plug the DC Adapter into the DC IN 16 V jack on the LCD TV. Plug the power cable into an outlet. Turn on the LCD TV and other equipment. 4.Press the SOURCE button on the remote control to select HD. HD will appear in the upper left corner on the TV screen. 5.Insert a DVD disc into the DVD player and press the PLAY button on the DVD Player.
On Screen Display
PC MODE 1st Layer PICTURE 2nd Layer SMART PICTURE 3rd Layer NORMAL WARM COOL
Magnavox LCD TV
9
Go to cover page
BRIGHTNESS CONTRAST AUTO ADJUST
YES IN PROGRESS STORE? PHASE CLOCK HORIZONTAL VERTICAL PERSONAL NEWS MUSIC THEATRE TREBLE BASS BALANCE STEREO VIRTUAL SURROUND OFF YES NO SIZE
YES NO
MANUAL ADJUST
AUDIO SMART SOUND
SETTINGS
STEREO VIRTUAL SURROUND AVL FEATURES PIP
VIDEO
AUDIO DISPLAY
OFF SMALL MEDIUM LARGE PBP TV AV S-VIDEO COMPONENT PC PIP ICON1 ICON2 ICON3 ICON4
SOURCE
PC TV AV S-VIDEO HD ENGLISH FRANÇ AIS ESPAÑ OL YES? 3rd Layer PERSONAL MOVIES SPORTS WEAK SIGNAL MULTIMEDIA NIGHT 4th Layer 5th Layer
INSTALL LANGUAGE
1st Layer PICTURE
FACTORY RESET TV / AV/ S-VIDEO / HDTV MODE 2nd Layer SMART PICTURE
BRIGHTNESS CONTRAST COLOR SHARPNESS TINT AUDIO SMART SOUND PERSONAL NEWS MUSIC THEATRE
10
Magnavox LCD TV Go to cover page
On Screen Display
AUDIO
SETTINGS
STEREO
VIRTUAL SURROUND AVL FEATURES SOURCE
TREBLE BASS BALANCE STEREO SAP MONO VIRTUAL SURROUND OFF YES NO PC TV AV S-VIDEO HD 4:3 EXPAND 4:3 COMPRESS 16:9 LOCK PROGRAM CHANGE CODE CLEAR ALL BLOCK OPTION MOVIE RATING
PICTURE FORMAT
PICTURE ALIGNMENT AUTO LOCK
TV RATING
YES ON OFF ON OFF G PG PG13 R NC17 X TV Y TV Y7 TV G TV PG
ON/OFF ON/OFF ON/OFF ON/OFF ON/OFF ON/OFF ON/OFF BLOCK FV ON/OFF BLOCK V S L D BLOCK V S L D BLOCK V S L ON/OFF ON/OFF ON/OFF ON/OFF ON/OFF ON/OFF ON/OFF ON/OFF ON/OFF ON/OFF ON/OFF ON/OFF ON/OFF ON/OFF ON/OFF ON/OFF
TV 14
TV MA
CLOSED CAPTION
CAPTION MODE
CC DISPLAY INSTALL LANGUAGE ENGLISH FRANÇ AIS ESPAÑ OL ATENNA CABLE AUTO START? CHANNEL SKIPPED
CC1 CC2 CC3 CC4 TXT1 TXT2 TXT3 TXT4 CC MUTE ON OFF
TUNER MODE
AUTO PROGRAM CHANNEL EDIT
ACTIVE SKIPPED
MANUAL FINE TUNE FACTORY RESET
YES?
Aging Mode
Magnavox LCD TV
11
Go to cover page
ATTENTION NO VIDEO INPUT
Access Aging.. Mode
Step 1 : Select the source "PC" and then turn off LCD-TV, and disconnect Interface Cable between Monitor and PC. Step 2 : [Push "power " button and then push the "VOL- " and "VOL+" buttons at the same time immediately and hold it] untill comes out " AGING screen" then release all buttons. Bring up:
AGING...
After 55 seconds, bring up:
After 5 seconds, bring up:
AGING...
After 55 seconds, bring up:
------------------repeatly Connect Signal cable again=> go back to normal display
12
Magnavox LCD TV Go to cover page
Warning Message
1.Automatic adjustment (for factory only) Press Volume+ and Volume- on front key at the same time (PC mode only). It adjusts PC image to the best and save the screen automatically. 2. OUT OF RANGE If PC input timing is out of range, it shows "OUT OF RANGE " warning message on the center of the screen. The range of horizontal frequency is between 14 - 63 KHz. The range of vertical frequency is between 45 - 76 Hz. The OSD won' t timeout. 3.NO VIDEO INPUT When PC input timing has either horizontal frequency or vertical frequency. Or neither has horizontal frequency nor vertical frequency. It shows on the center of the screen for 30 seconds, then it will enter sleep mode.
Factory Mode
Access factory. Mode how to get into factory mode menu Step 1 : Select the source "PC" and then turn off LCD-TV. Step 2 : [Push "power " button and then push the "VOL- " and "VOL+" buttons at the same time immediately and hold it] about five seconds then release all buttons. Press "menu"button and bring up factory mode indication as shown in Fig.1
Magnavox LCD TV
13
Go to cover page
MAIN CONTROLS PICTURE AUDIO FEATURES INSTALL
1024X768@60HZ
SMART PICTURE BRIGHTNESS CONTRAST AUTO ADJUST MANUAL ADJUST
F1/FL1 NAFTA V1.01.05 041208 LG15XGA
Fig.1 Use the CHNNEL- and CHNNEL+ to select the "F1/FL1 NAFTA V1.01. 05 041208 LG15XGA" and then press the "VOL +" button
Menu Item
Scalar Gain R G B Auto-Color ADC Offset R G B ADC Gain R G B PC Offset R G B 711X SDTV Brightness 711X SDTV SAT. 711X SDTV Contrast 711X SDTV TINT TV Shift H V HD Shift H V Show Lock Message HDTV ADC Offset R G B HDTV ADC Gain R G B Video Scalar Gain R G B Scalar Hue
Description
Scalar Gain for Normal/Warm/Cool in PC mode. Adjust color from received signal (either in PC or HDTV mode). Adjust AD 9883 for PC ADC offset. Adjust AD 9883for PC ADC gain. PC analog scalar offset. Adjust SA 7119 SDTV brightness. Adjust SA 7119 SDTV saturation. Adjust SA 7119 SDTV contrast. Adjust SA 7119 SDTV tint (hue). Adjust TV screen position horizontally/vertically. Adjust HDTV screen position horizontally/vertically. Show OSD lock message. Adjust AD 9883 for HDTV ADC offst. e Adjust AD 9883 for HDTV ADC gain. Adjust scalar gain for Video mode. Adjust scalar hue.
14
Magnavox LCD TV Go to cover page
Trouble shooting
No Power .Check the TV power cord. Disconnect the power cord from the power outlet for 10 seconds, then reinsert the plug into the outlet. Press POWER to turn on the TV again. .Make sure the outlet is not on a wall switch. .Make sure a fuse has not blown at the power outlet. No Picture .Check the antenna or Cable TV connections. Connect the antenna or Cable TV signal securely to the TV' 75ohm jack on the rear of the TV. s .Set TUNER MODE correctly. Details are on page 15. .Activate AUTO PROGRAM to find all available channels. In case you hear only sound and don' see any picture in S-Video or t Video (CVBS) mode. Please check if you have connected Video signal to S-Video or Video (CVBS) input. Only one of the two video inputs can be connected to sound. This means that the same sound can be heared in S-Video and Video (CVBS) mode. No Sound .Press the VOL+ and VOL- buttons to adjust the volume. .Press the MUTE button on the remote control to cancel or restore the volume. .If you have connected other equipment to the TV (such as a VCR or DVD Player), make sure the audio cables are connected securely between the TV and the other equipment. .Check the SOUND settings. .In case you hear wrong sound in S-Video or Video (CVBS) mode. Please check if you have connected the right sound signal to AV in (S-Video or Video input). Only one of the two video inputs can be connected to sound, but both video signals can be connected. This means that only one of the two sound inputs can be heared in S-Video and Video (CVBS) mode. Remote Control does not work. .Check the batteries. If necessary, replace them with two AAA heavy duty (zinc chloride) or alkaline batteries. .Clean the remote control as well as the remote control sensor on the front of the TV. .Check the TV power cord. Disconnect the power cord from the power outlet for 10 seconds, then reinsert the plug into the outlet. Press POWER to turn on the TV again. .Make sure the outlet is not on a wall switch. .Make sure a fuse has not blown at the power outlet. .Always point the remote control toward the front of the TV (toward the remote sensor). .Make sure that you use the supplied Magnavox Remote control, only the supplied Magnavox Remote control can be used with this LCD-TV set. TV displays wrong channel or no channels. .Repeat channel selection. .Add the channel number(s) into the TV' memory. Use STORE. s .Make sure TUNER MODE is set correctly. Then activate AUTO PROGRAM to set up all available channels.
Failure Mode Of Panel
Quick reference for failure mode of LCD panel this page presents problems that could be made by LCD panel. It is not necessary to repair circuit board. Simply follow the mechanical instruction on this manual to eliminate failure by replace LCD panel.
Magnavox LCD TV
15
Go to cover page
Polarizer has bubbles
Failure description
Phenomenon
Vertical block defect
Polarizer has bubbles
Vertical dim lines
Foreign material inside polarizer. It shows liner or dot shape. Vertical lines defect (Always bright or dark)
Concentric circle formed
Horizontal block defect
Bottom back light of LCD is brighter than normal Horizontal dim lines
Back light un-uniformity
Horizontal lines defect (Always bright or dark)
Has bright or dark pixel
Backlight has foreign material. Black or white color, liner or circular type
16
Magnavox LCD TV Go to cover page
Wiring diagram
Magnavox LCD TV
17 Go to cover page
Front view
Fig.5 Fig.1
Back view, remove the cover as Fig.2 Fig.6
Fig.2
Fig.7
Remove the base: unscrew the screws as Fig.3
Fig.3
Remove the Matel frame board - Remove the five screws - Remove the matel frame board as shown in Fig.8
Remove the back cover, unscrew the screws as Fig.4 and the open the clicks and then remove the back cover as Fig.5 Fig.6 Fig.7 Fig.8
Remove the inverter board ,YPbPr-in and scaler board unscrew the screws and disconnect the connector as shown in Fig.9
Fig.4
18
Magnavox LCD TV Go to cover page
Fig.9
Fig.10
Fig.13
Fig.11
Fig.14
Fig.12
Electrical instruction(15MF607T/17)
1.General points 1.1 During the test and measuring, supply a distortion free AC mains Voltage to the apparatus via an isolated transformer with low Internal resistance. 1.2 All measurements mentioned hereafter are carried out at a normal mains voltage (90 - 132 VAC for USA version, 195 -264 VAC for EUROPEAN version, or 90 - 264 VAC for the model with full range power supply, unless otherwise stated.) 1.3 All voltages are to be measurement or applied with respect to ground, unless otherwise stated. 1.4 The test has to be done on a complete set including LCD panel in a room with temperature of 25 +/- 5 degree C. 1.5 All values mentioned in these test instruction are only applicable of a Well aligned apparatus, with correct signal. 1.6 The letters symbols (B) and (S) placed behind the test instruction Denotes (B): carried out 100% inspection at assembly line (S): carried out test by sampling 1.7 The white balance (color temperature), has to be tested in subdued Lighted room. 1.8 Repetitive power on/off cycle are allowed except it should be avoided within 6 sec. 2. Input signal 2.1.1 PC Signal type Analog Video : 0.7 Vp-p linear, positive polarity Separate Sync. : TTL level, separate, positive or negative polarity Audio signal : Mini-jack audio input Input level: 500 mVrms ((Speaker outpout 3W when Input level > 630mVrms and Volume control at 100%)) Signal source: pattern generator format as attachment (table 1 to 11) Reference generator : CHROMA 2200 or 2250 2.1.2 TV Signal type RF Signal : Aerial input, NTSC cable and antenna system. Video signal : Cinch input, CVBS with NTSC and PAL system. Level: 1.0Vp-p (0.7V video + 0.3V sync.) S video input: Y/C signal, NTSC and PAL system. Level: Y: 1.0Vp-p (0.7V video + 0.3V sync.) C: +/- 0.3V. Component input: Cinch G/B/R-> YPbPr cinch input. Level: Y: 1.0Vp-p Pb/Pr: +/- 0.35V Audio signal : Side cinch R/L for CVBS and S-video Bottom cinch R/L for component input. Input level: 500 mVrms ((Speaker outpout 3W when Input level > 630mVrms and Volume control at 100%)) 2.2 PC Input signal mode PRE-LOAD VIDEO RESOLUTION Mode 3, 6, 7, 10 are preset modes that should pass QA inspection. Mode 1, 2, 4, 5, 8, 9, 11 will run auto adjustment only, and W/O QA checking. Mode Resolution V.freq (Hz) Dot rate (MHz) H.freq 1 2 3 4 5 6 7 8 9 10 11 25.175 28.322 25.175 30.240 31.500 36.000 40.000 49.500 57.300 65.000 78.750 31.469 31.469 31.469 35.000 37.500 35.156 37.879 46.875 49.700 48.363 60.023 IBM VGA IBM VGA IBM VGA MACINTOSH VESA VESA VESA VESA MACINTOSH VESA VESA 640 * 350 720 * 400 640 * 480 640 * 480 640 * 480 800 * 600 800 * 600 800 * 600 832 * 624 1024 * 768 1024 * 768 70.087 70.087 59.940 66.667 75.000 56.250 60.317 75.000 75.000 60.004 75.029
Magnavox LCD TV
19
Go to cover page
2.3 TV input signal Channel and pattern for Nafta model (Table1) Signal Distribution Table ( NTSC)
Table 1 3. TV mode display adjust ment 3.1 White balance adjustment (B) General set-up : Equipment Requirements: Color analyzer. Input requirements: Input Signal Type : CVBS-NTSC signal. Frequency = 187.25 MHz (CH. 9). Alignment method: Initial Set-up : Set TV (7119) Brightness=124; Contrast=64, Saturate= 70 in Factory mode (can be fine tuned) Set Smart picture as "Personal "(Brightness=50, Color=50, Contrast=50) Apply" 100% Full White/100IRE" pattern by TV pattern generator. Alignment : Adjust the VIDEO SCALER GAIN R G B in Factory Mode NORMAL . (See Fig 1.) [ Enter factory menu : press Volume - and Volume + keys together around six seconds] The 1931 CIE chromaticity (X, Y) co-ordinates shall be: Picture Mode Normal (Original) X 0.289 ± 0.005 y 0.304 ± 0.005
Table3.1: Readings with Minolta CA -110.
20
Magnavox LCD TV Go to cover page
FACTORY ADJUST MENU NORMAL SCALER GAIN R G B AUTO-COLOR (OK) ADC OFFSET R G B ADC GAIN R G B PC OFFSET R G B 7119 SDTV SAT TV SHIFT H V HD SHIFT H V SHOW LOCK MESSAGE HDTV ADC OFFSET R HDTV ADC GAIN R VIDEO SCALER GAIN R SCALER HUE EXIT Value
Electrical instruction
(Or FLUKE 54200, apply576i, DIGITAL SCAN/DIGI_ADC1 pattern.)
TINT
Alignment method: Initial Set up : Set Smart picture as Personal, Brightness=50, Color=50, Contrast=50) et AUTO-COLOR process. S Alignments :Check chromaticity (X, Y) co -ordinates s pecification:
G B G B G B
Picture Mode
Fig.1 4. PC mode display adjustment 4.1Display quality adjustment Use timing mode as de s cribe in 2.2, and use the POPO (pixel on pixel off) patternto adjust the clock until no stripe and adjust the phase until clear picture.(AUTO ADJUST hot key: press Volume- and Volume + keys togetherfor 1 second.) Check all pre 4 modes. set 4.2 WHITE-D adjustment (B) 4.2.1 At factory mode apply 1024X768/60Hzmode with 64 gray pattern. Set main controls Brightness at 50% and Contrast to 50%. Select AUTO-COLOR function for ADC OFFSETand ADC GAIN setup. " 4.2.2 Set smart picture as NORMAL" Set SCALER GAIN R G B= VIDEO SCALER GAIN R G B (alignment done). The 1931 CIE chromaticity (X, Y) co -ordinates shall be: Normal/ (8500°K)
If out of specification, fine-tune HDTV ADC Gainin factory mode. 6. Preset EEPROM data 6.1 EEPROM data has to be preset data according following table. Factory mode preset. Preset value Function SCALER GAIN ADC Offset R/G/B ADC Gain R/G/B PC OFFset R/G/B 7119 ? brightness 7119 Saturation 7119 contrast 7119 TINT TV shift H TV shift V HD SHIFT H HD SHIFT V HD ADC OFFset R G B HD ADC GAIN R G B Video Scaler Gain Scaler Hue Regular 127 127 127 127 127 127 127 127 127 127 127 127 124 (TV,AV,S-video,HD) 64 (TV,AV,S-video,HD) 70 (TV,AV,S-video,HD) 24 (TV,AV,S-video,HD) NTSC PAL 170 20 See below. 181 22
127 127 127
127 127 127 50
127 127 127
Readings with Minolta CA 110. 4.2.3 Set Smart picture as WARM , and COOL The SCALER GAIN RG B = . Normal/ the R' \B' are \G' gain after alignment. ' ' ' 4.3 Check the analog interface cable ' ' ' ' ' ' WARM COOL
Factory mode:
In user Picture alignment
Check the color poor & noise condition of 64 gray pattern. 5. HDTV mode display adjust ment 5.1 White balance adjustment (B) General set-up: Equipment : Quantum Data Pattern Generator 801GD or 802G. Apply 1080i, RGBWgray pattern.
Electrical instruction
6.2 Smart picture &Smart sound: 6.2.1 Final TV mode out box setting. Smart Picture : Sport
Smart sound
Magnavox LCD TV
21
Go to cover page
Smart Picture
TIMING FOR F1 15" TFT XGA COLOR LCD MONITOR (VESA monitor timing standard Version 1.0 Release 0.7) REFERENCE PATTERN GENERATOR : CHROMA 2200 or2250 TABLE 1: 31.469 KHz/70.087Hz, 640 X 350, pixel=25.175 MHz Vertical Horizontal Frame border=0 Frame border=0 Total size =31.778 ms Total size =14.268 ms Display size=25.422 ms Display size=11.122 ms Rear porch= 1.907 ms Rear porch= 1.907 ms Sync width= 3.813 ms Sync width= 0.064 ms Sync polarity=+ Sync polarity= TABLE 2: 31.469 KHz/70.087Hz, 7 20 X 400, pixel=28.322 MHz Vertical Horizontal Frame border=0 Frame border= 0 Total size =31.778 ms Total size =14.268 ms Display size=25.422 ms Display size=12.711 ms Rear porch= 1.907 ms Rear porch= 1.112 ms Sync width= 3.813 ms Sync width= 0.064 ms Sync polarity=Sync polarity=+ TABLE 3: 31.469 KHz/59.940Hz, 640 X 480, pixel=25.175 MHz Vertical Horizontal Frame border=0 Total size =31.778 ms Display size=25.422 ms Rear porch= 1.907 ms Sync width= 3.813 ms Sync polarity=Smart Sound : Personal SOUND VOLUME : 15 BASE : 50 TREBLE : 50 Balance : 0 Virtuel SURROUND: OFF AVL : NO Frame border=0 Total size =16.683 ms Display size=15.253 ms Rear porch= 1.049 ms Sync width= 0.064 ms Sync polarity=-
TABLE 4: 35.000 KHz/66..667Hz, 640 X 480, pixel=30.240 MHz Vertical Horizontal Frame border=0 Total size =28.571 ms Display size=21.164 ms Rear porch= 3.175 ms Sync width= 2.116 ms Sync polarity=Frame border=0 Total size =15.000 ms Display size=13.714 ms Rear porch= 1.114 ms Sync width= 0.086 ms Sync polarity=-
22
Magnavox LCD TV Go to cover page
Electrical instruction
TABLE 10: 48.363 KHz/60.004Hz, 1024 X 768, pixel=65.000 MHz Horizontal Vertical Frame border=0 Total size =20.677 ms Display size=15.754ms Rear porch= 2.462ms Sync width= 2.092ms Sync polarity= Frame border=0 Total size =16.666 ms Display size=15.880 ms Rear porch= 0.600 ms Sync width= 0.124 ms Sync polarity= -
TABLE 5: 37.500 KHz/75.000Hz, 640 X 480, pixel=31.500 MHz Horizontal Vertical Frame border=0 Total size =26.667 ms Display size=20.317ms Rear porch= 3.810ms Sync width= 2.032 ms Sync polarity= Frame border=0 Total size =13.333 ms Display size=12.800 ms Rear porch= 0.427 ms Sync width= 0.080 ms Sync polarity= -
TABLE 6: 35.156 KHz/56.250Hz, 800 X 600, pixel=36.000 MHz Horizontal Vertical Frame border=0 Total size =28.444 ms Display size=22.222ms Rear porch= 3.556ms Sync width= 2.000ms Sync polarity= + Frame border=0 Total size =17.778 ms Display size=17.067 ms Rear porch= 0.626 ms Sync width= 0.057 ms Sync polarity= +
TABLE 11: 60.023 KHz/75.029Hz, 1024 X 768, pixel=78.750 MHz Horizontal Frame border=0 Total size =16.660 ms Display size=13.003ms Rear porch= 2.235ms Sync width= 1.219ms Sync polarity= + Vertical Frame border=0 Total size =13.328 ms Display size=12.795 ms Rear porch= 0.466 ms Sync width= 0.050 ms Sync polarity= +
TABLE 7: 37.879 KHz/60.317Hz, 800 X 600, pixel=40.000 MHz Horizontal Frame border=0 Total size =26.400 ms Display size=20.000ms Rear porch= 2.200ms Sync width= 3.200ms Sync polarity= + Vertical Frame border=0 Total size =16.579 ms Display size=15.840 ms Rear porch= 0.607 ms Sync width= 0.106 ms Sync polarity= +
TABLE 8: 46.875 KHz/75.000Hz, 800 X 600, pixel=4 9.500 MHz Vertical Horizontal Frame border=0 Total size =21.333 ms Display size=16.162ms Rear porch= 3.232ms Sync width= 1.616ms Sync polarity =+ Frame border=0 Total size =13.333 ms Display size=12.800 ms Rear porch= 0.448 ms Sync width= 0.064 ms Sync polarity= +
TABLE 9: 49.722 KHz/74.546Hz, 832 X 624, pixel=57.280 MHz Horizontal Vertical Frame border=0 Total size =20.110 ms Display size=14.520ms Rear porch= 3.910ms Sync width= 1.117ms Sync polarity= + Frame border=0 Total size =13.410 ms Display size=12.550 ms Rear porch= 0.784 ms Sync width= 0.060 ms Sync polarity= +
Display adjustment
Display adjustment
Access factory. Mode how to get into factory mode menu Step 1 : Select the source "PC" and then turn off LCD-TV. Step 2 : [Push "power " button and then push the "VOL- " and "VOL+" buttons at the same time immediately and hold it] about five seconds then release all buttons. Press "menu"button and bring up factory mode indication as shown in Fig.1
Magnavox LCD TV
23
Go to cover page
Fig.3
MAIN CONTROLS PICTURE AUDIO FEATURES INSTALL
1024X768@60HZ
2. Apply a 1024x768/60Hz signal with white pattern.Set brightness control at 50% and contrast control at 50%. Adjust the R.G.B gain to reach special color temperature on center of screen. 2.1 Aim the probe CA-A30 at the center of screen as Fig. 4 2.2 Remove the lens protective cover of probe CA-A30.
SMART PICTURE BRIGHTNESS CONTRAST AUTO ADJUST MANUAL ADJUST
F1/FL1 NAFTA V1.01.05 041208 LG15XGA
Fig. 1 Use the CHNNEL- and CHNNEL+ to select the "F1/FL1 NAFTA V1.01. 05 041208 LG15XGA" and then press the "VOL +" button
2.3 Set Measuring/viewing selector to Measuring position for reset analyzer. (Zero calibration) as Fig. 5 2.4 Turn on the colour analyzer (CA-110). 2.5 Press 0-CAL button to start reset analyzer. See Fig. 6
Cover (black) Measurement viewing selector
Fig.4
Fig.5
O-CAL
Fig.6
Fig.2
2.6 Switch light probe to Viewing position. 2.7 Move the Lens barrel forward or backward to get clear image as shown in Fig. 7 2.8 Switch light probe to Measuring position. It should be able to indicate colour value on the CA-110.
Clear image
PC mode WHITE-D adjustment (B) 1 Apply 1024X768/60Hz mode with 5 block pattern as Fig 3. Set main controls brightness control at 50% and contrast to 50% on User mode. Set color setting at natural color on User mode. Move cursor to "AUTO-color" item on factory mode, press "menu" key to active this function, then scaler will adjust RGB and Color RGB automatically by it self.
Measurement/viewing selector
Fig.7
24
Magnavox LCD TV Go to cover page
Display Adjustment
2.9 Set smart picture as " NORMAL" Set SCALER GAIN R G B = VIDEO SCALER GAIN R G B(alignment done). The 1931 CIE chromaticity (X, Y) co-ordinates shall be: Normal/ (8500°K) x (center) y (center) 0.289 ± 0.030 0.304 ± 0.030
Readings with Minolta CA-110. 2.10 Set Smart picture as" WARM", and " COOL" The SCALER GAIN R G B = . Normal/ the R' \G' \B' are R gain G gain B gain gain after alignment. R' G' B' WARM R' G '-10 B '-10 COOL
' R -10
G' -10 B'
DDC DATA
LPL panel: ********************************************************************** EDID log file ********************************************************************** Vendor/Product Identification ID Manufacturer Name ID Product Code ID Serial Number Week of Manufacture Year of Manufacture EDID Version, Revision Version Revision Monitor Descriptor #4 Monitor Range Limits Min. Vt rate Hz Max. Vt rate Hz Min. Horiz. rate kHz Max. Horiz. rate kHz Max. Supported Pixel
Magnavox LCD TV
25
Go to cover page
: 58 : 62 : 30 : 49 : 70
: : : : :
PHL 4650 (HEX.) 1010101 (HEX.) 0 2004
No secondary GTF timing formula supported. Extension Flag Check sum : 0 : F8 (HEX.)
: 1 : 3
Basic Display Parameters/Features Video Input Definition : Analog Video Input 0.700V/0.300V (1.00Vpp) without Blank-to-Black Setup Separate Sync without Composite Sync without Sync on Green no Serration required Maximum H Image Size Maximum V Image Size : 30 : 23
********************************************************************** EDID data (128 bytes) ********************************************************************** 0: 00 1: ff 2: ff 3: ff 4: ff 5: ff 6: ff 7: 00 8: 41 9: 0c 10: 50 11: 46 12: 01 13: 01 14: 01 15: 01 16: 00 17: 0e 18: 01 19: 03 20: 08 21: 1e 22: 17 23: 78 24: ee 25: b4 26: 43 27: 9e 28: 57 29: 4c 30: 94 31: 26 32: 15 33: 4a 34: 4d 35: 23 36: 08 37: 00 38: 01 39: 01 40: 01 41: 01 42: 01 43: 01 44: 01 45: 01 46: 01 47: 01 48: 01 49: 01 50: 01 51: 01 52: 01 53: 01 54: 00 55: 00 56: 00 57: ff 58: 00 59: 0a 60: 20 61: 20 62: 20 63: 20 64: 20 65: 20 66: 20 67: 20 68: 20 69: 20 70: 20 71: 20 72: 00 73: 00 74: 00 75: ff 76: 00 77: 0a 78: 20 79: 20 80: 20 81: 20 82: 20 83: 20 84: 20 85: 20 86: 20 87: 20 88: 20 89: 20 90: 00 91: 00 92: 00 93: fc 94: 00 95: 50 96: 68 97: 69 98: 6c 99: 69 100: 70 101: 73 102: 20 103: 46 104: 31 105: 20 106: 31 107: 35 108: 00 109: 00 110: 00 111: fd 112: 00 113: 3a 114: 3e 115: 1e 116: 31 117: 07 118: 00 119: 0a 120: 20 121: 20 122: 20 123: 20 124: 20 125: 20 126: 00 127: f8
Display Transfer Characteristic : 2.2 (gamma) Feature Support (DPMS) : Standby Suspend Active Off
Display Type : RGB color display Standard Default Color Space : Primary color space Preferred Timing Mode : Detailed timing block 1 Color Characteristics Red X coordinate Red Y coordinate Green X coordinate Green Y coordinate Blue X coordinate Blue Y coordinate White X coordinate White Y coordinate Established Timings Established Timings I
: 0.619 : 0.343 : 0.298 : 0.578 : 0.149 : 0.082 : 0.289 : 0.304
: 640 x 480 @60Hz (IBM,VGA) 800 x 600 @56Hz (VESA) 800 x 600 @60Hz (VESA) : 1024 x 768 @60Hz (VESA) : : Unused
Established Timings II Manufacturer's timings Standard Timing Identification Monitor Descriptor #1 Serial Number Monitor Descriptor #2 Serial Number Monitor Descriptor #3 Monitor Name
:
:
: Philips F1 15
26
Magnavox LCD TV
Go to cover page
DDC DATA
Monitor Descriptor #3 Monitor Name Monitor Descriptor #4 Monitor Range Limits Min. Vt rate Hz Max. Vt rate Hz Min. Horiz. rate kHz Max. Horiz.rate kHz Max. Supported Pixel : Philips F1 15
AUO panel: ********************************************************************** EDID log file ********************************************************************** Vendor/Product Identification ID Manufacturer Name ID Product Cod e ID Serial Number Week of Manufacture Year of Manufacture EDID Version, Revision Version Revision
: 58 : 62 : 30 : 49 : 70
: PHL : 4650 (HEX.) : 1010101 (HEX.) : 0 : 2004
No secondary GTF timing formula supported. Extension Flag : 0 : 44 (HEX.)
: 1 : 3
Check sum
Basic Display Parameters/Features Video Input Definition : Analog Video Input 0.700V/0.300V (1.00Vpp) without Blank -to-Black Setup Separate Sync without Composite Sync without Sync on Green no Serration required Maximum H Image Size Maximum V Image Size : 30 : 23
**************************************** ****************************** EDID data (128 bytes) ********************************************************************** 0: 00 1: ff 2: ff 3: ff 4: ff 5: ff 6: ff 7: 00 8: 41 9: 0c 10: 50 11: 46 12: 01 13: 01 14: 01 15: 01 16: 00 17: 0e 18: 01 19: 03 20: 08 21: 1e 22: 17 23: 8c 24: ee 25: b9 26: ea 27: 9a 28: 58 29: 48 30: 95 31: 25 32: 16 33: 47 34: 4a 35: 23 36: 08 37: 00 38: 01 39: 01 40: 01 41: 01 42: 01 43: 01 44: 01 45: 01 46: 01 4 7: 01 48: 01 49: 01 50: 01 51: 01 52: 01 53: 01 54: 00 55: 00 56: 00 57: ff 58: 00 59: 0a 60: 20 61: 20 62: 20 63: 20 64: 20 65: 20 66: 20 67: 20 68: 20 69: 20 70: 20 71: 20 72: 00 73: 00 74: 00 75: ff 76: 00 77: 0a 78: 20 79: 20 80: 20 81: 20 82: 20 83: 20 84: 20 85: 20 86: 20 87: 20 88: 20 89: 20 90: 00 91: 00 92: 00 93: fc 94: 00 95: 50 96: 68 97: 69 98: 6c 99: 69 100: 70 101: 73 102: 20 103: 46 104: 31 105: 20 106: 31 107: 35 108: 00 109: 00 110: 00 111: fd 112: 00 113: 3a 114: 3e 115: 1e 116: 31 117: 07 118: 00 119: 0a 120: 20 121: 20 122: 20 123: 20 124: 20 125: 20 126: 00 127: 44
Display Transfer Characteristic : 2.4 (gamma) Feature Support (DPMS) : Standby Suspend Active Off
Display Type : RGB color display Standard Default Color Space : Primary color space Preferred Timing Mode : Detailed timing block 1 Color Characteristics Red X coordinate Red Y coordinate Green X coordinate Green Y coordinate Blue X coordinate Blue Y coordinate White X coordinate White Y coordinate Established Timings Established Timings I
: 0.604 : 0.347 : 0.283 : 0.583 : 0.147 : 0.088 : 0.279 : 0.291
: 640 x 480 @60Hz (IBM,VGA) 800 x 600 @56Hz (VESA) 800 x 600 @60Hz (VESA) : 1024 x 768 @60Hz (VESA) : : Unused
Established Timings II Manufacturer's timings Standard Timing Identification Monitor Descriptor #1 Serial Number Monitor Descriptor #2 Serial Number
:
:
DDC DATA
9.3 CPT panel: ********************************************************************** EDID log file ********************************************************************** Vendor/Product Identification ID Manufacturer Name ID Product Code ID Serial Number Week of Manufacture Year of Manufacture EDID Version, Revision Version Revision Monitor Name
Magnavox LCD TV
27
Go to cover page
: Philips F1 15
: PHL : 4650 (HEX.) : 1010101 (HEX.) : 0 : 2004
Monitor Descriptor #4 Monitor Range Limits Min. Vt rate Hz Max. Vt rate Hz Min. Horiz. rate kHz Max. Horiz. rate kHz Max. Supported Pixel
: 58 : 62 : 30 : 49 : 70
No secondary GTF timing formula supported. Extension Flag Check sum : 0 : DE (HEX.)
: 1 : 3
Basic Display Parameters/Features Video Input Definition : Analog Video Input 0.700V/0.300V (1.00Vpp) without Blank-to-Black Setup Separate Sync without Composite Sync without Sync on Green no Serration required Maximum H Image Size Maximum V Image Size : 30 : 23
********************************************************************** EDID data (128 bytes) ********************************************************************** 0: 00 1: ff 2: ff 3: ff 4: ff 5: ff 6: ff 7: 00 8: 41 9: 0c 10: 50 11: 46 12: 01 13: 01 14: 01 15: 01 16: 00 17: 0e 18: 01 19: 03 20: 08 21: 1e 22: 17 23: 82 24: ee 25: b2 26: 45 27: a4 28: 55 29: 4c 30: 96 31: 24 32: 14 33: 50 34: 54 35: 23 36: 08 37: 00 38: 01 39: 01 40: 01 41: 01 42: 01 43: 01 44: 01 45: 01 46: 01 47: 01 48: 01 49: 01 50: 01 51: 01 52: 01 53: 01 54: 00 55: 00 56: 00 57: ff 58: 00 59: 0a 60: 20 61: 20 62: 20 63: 20 64: 20 65: 20 66: 20 67: 20 68: 20 69: 20 70: 20 71: 20 72: 00 73: 00 74: 00 75: ff 76: 00 77: 0a 78: 20 79: 20 80: 20 81: 20 82: 20 83: 20 84: 20 85: 20 86: 20 87: 20 88: 20 89: 20 90: 00 91: 00 92: 00 93: fc 94: 00 95: 50 96: 68 97: 69 98: 6c 99: 69 100: 70 101: 73 102: 20 103: 46 104: 31 105: 20 106: 31 107: 35 108: 00 109: 00 110: 00 111: fd 112: 00 113: 3a 114: 3e 115: 1e 116: 31 117: 07 118: 00 119: 0a 120: 20 121: 20 122: 20 123: 20 124: 20 125: 20 126: 00 127: de
Display Transfer Characteristic : 2.3 (gamma) Feature Support (DPMS) : Standby Suspend Active Off
Display Type : RGB color display Standard Default Color Space : Primary color space Preferred Timing Mode : Detailed timing block 1 Color Characteristics Red X coordinate Red Y coordinate Green X coordinate Green Y coordinate Blue X coordinate Blue Y coordinate White X coordinate White Y coordinate Established Timings Established Timings I
: 0.643 : 0.335 : 0.297 : 0.588 : 0.142 : 0.078 : 0.313 : 0.329
: 640 x 480 @60Hz (IBM,VGA) 800 x 600 @56Hz (VESA) 800 x 600 @60Hz (VESA) : 1024 x 768 @60Hz (VESA) : : Unused
Established Timings II Manufacturer's timings Standard Timing Identification Monitor Descriptor #1 Serial Number Monitor Descriptor #2 Serial Number Monitor Descriptor #3
:
:
28
Magnavox LCD TV Go to cover page
DDC INSTRUCTIONS
Note: The alignment box has already build-in a batteries socket for using batteries (8~12V) as power source. Pull out the socket by remove four screws at the rear of box. Please do not forget that remove batteries after programming. The energy of batteries can only drive circuits for a short period of time.
General
DDC Data Re-programming In case the DDC data memory IC or main EEPROM which storage all factory settings were replaced due to a defect, the serial numbers have to be re-programmed"Analog DDC IC, & EEPROM". It is advised to re-soldered DDC IC and main EEPROM from the old board onto the new board if circuit board have been replaced, in this case the DDC data does not need to be re-programmed. Additional information Additional information about DDC (Display Data Channel) may be obtained from Video Electronics Standards Association (VESA). Extended Display Identification Data(EDID) information may be also obtained from VESA.
To Monitor D-sub cable
To Printer port
System and equipment requirements
1. 2. An i486 (or above) personal computer or compatible. Microsoft operation system Windows 95/98 . You have to Install the EDID_PORT_Tool under Win2000/XP . As Fig. 1 . Fig. 1
To PC
Fig. 3
Pin assignment
SIGNAL A.PIN No. 15-pin D-Sub Connector 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Red Green Blue GND GND Red GND Green GND Blue GND +5V (Supply from PC) Sync GND GND Bi-directional data H-sync V-sync Data clock
A. Cody the "UserPort.sys" to C:\WINNT\system32\drivers(win2000)
C:\WINDOWS\system32\drivers(winXP) B. Running " io.exe" everytime, Before you start to programming edid data .
3. 4.
EDID45.EXE program . A/D Alignment kits (3138 106 10396): inclusion : a. Alignment box x1 (as Fig. 2)
Fig. 2
b. Printer cable x1 c. (D-Sub) to (D-Sub) cable x1
DDC INSTRUCTIONS
Magnavox LCD TV
29
Go to cover page
3. At the submenu, type the letter of your computer's hard disk drive followed by :EDID45 (for example, C:\EDID45, as shown in Fig. 6).
5
Fig. 6
1
4. Click OK button. The main menu appears (as shown in Fig. 7). This is for initialize alignment box.
PC
1=Power connector 2=D-SUB connector
Fig. 7
To printer port (LTP1)
Fig. 4
----->
----->
1
Printer Port
To Monitor
2
To PC
Note 1: If the connection is improper, you will see the following error message (as shown in Fig. 8) before entering the main menu. Meanwhile, the (read EDID) function will be disable. At this time, please make sure all cables are connected correctly and
TO VIDEO CARD 2
Method 1: Start on DDC program
Fig. 8
1
Fig. 5
Fig. 9
30
Magnavox LCD TV Go to cover page
DDC INSTRUCTIONS
Step 3: Modify DDC data (verify EDID version, week, year) 1. Click (new function) icon from the tool bar, bring up Step 1 of 9 as shown in Fig. 14 . EDID45 DDC application provides the function selection and text change (select & fill out) from Step 1 to Step 9.
Re-programming DDC IC
Step 1: After initialize alignment box, connecting all cables and box as shown in Fig. 10
PC
1=Power connector 2=D-SUB connector
To printer port (LTP1)
1
3138 106 10369
Printer Port To Monitor
-----> ----->
2
Fig. 10
To PC
To PC Video port (D-sub)
Step 2: Read DDC data from monitor 1. Click icon as shown in Fig. 11 from the tool bar to bring up the Channels "Configuration Setup" windows as shown in Fig. 12.
Fig. 14
Step 4: Modify DDC data (Monitor Serial No.) 1. Click Next , bring up Fig. 15.
Fig. 11 2. Select the DDC2Bi as the communication channel. As shown in Fig. 12.
Fig. 12
3. Click OK button to confirm your selection. 2. 4. Click icon (Read EDID function) to read DDC EDID data from monitor. The EDID codes will display on screen as shown in Fig. 13. Click Next , bring up Fig. 16.
Fig. 15
Fig. 13
Don't close this screen. --->
Fig. 16
DDC INSTRUCTIONS
3. Click Next , bring up Fig. 17. 6.
Magnavox LCD TV
31
Go to cover page
Click Next , bring up Fig. 20. - Serial number can be filled up or be changed at this moment.
Fig. 17 Fig. 20 4. Click Next , bring up Fig. 18. 7. Click Next , bring up Fig. 21.
Fig. 18 8.
Fig. 21 Click Next , bring up Fig. 20.
5.
Click Next , bring up Fig. 19.
Fig. 19
Fig. 22
32
Magnavox LCD TV Go to cover page
DDC INSTRUCTIONS
Step 7: Exit DDC program Pull down the File menu and select Exit as shown in Fig. 25.
Step 5: Write DDC data 1. Configuration should be as Fig. 23. And press OK.
Fig. 23 Access factory. Mode Step 1 : Select the source "PC" and then turn off LCD-TV. Step 2 : [Push "power " button and then push the "VOL- " and "VOL+" buttons at the same time immediately and hold it] about five seconds then release all buttons. Press "menu"button and bring up factory mode indication Fig. 25
3. Click (Write EDID) icon from the tool bar to write DDC data. Bring up "Writing 0%~100%, ready" a progressing bar on the left down corner. 4. Turn off/on monitor
Step 6: Save DDC data Sometimes, you may need to save DDC data as a text file for using in other IC chip. To save DDC data, follow the steps below: 1. Click (Save) icon (or click "file"-> "save as") from the tool bar And give a file name as shown in Fig. 24. The file type is EDID45 file (*.ddc) which can be open in WordPad. By using WordPad, the texts of DDC data & table (128 bytes, hex code) can be modified. If DDC TEXTS & HEX Table are completely correct, it can be saved as .ddc flie to re-load it into DDC IC for DDC Data application.
150S5-DDC 150F1-DDC
C:\My documents\150F1-DDC
45
Fig. 24 2. Click Save.
ISP Instruction
Configuration and procedure
"Easywriter " The software is provided by Novatek to upgrade the firmware of CPU. It is a windows-based program, which cannot be run in MS-DOS. DDC2BI_ISP TOOL (3138 106 10396) is for the interface between "Parallel Port of PC" and "15 pin-D-SUB connector of Monitor".
Magnavox LCD TV
33
Go to cover page
Fig. 4
System and equipment requirements
1. 2. 3. 4. An i486 (or above) personal computer or compatible. Microsoft operation system Windows 95/98/2000/XP. ISP Software " Easywrite " DDC2BI_ISP TOOL (3138 106 10396) as shown in Fig. 1
Step 5 :Copy the .hex code to C:\easywrite as shown in Fig. 5 .
170S5
Parallel Port to Print Port in PC
D-SUB to monitor Fig. 5 Update the firmware 1. Press the load hex then select the .hex code as shown in Fig.6
Fig. 1
5.
Connect DDC2BI_ISP TOOL and Mains cord to Monitor as shown in Fig. 2. Fig. 6
150F1 LCD TV(B)
D-Sub
PC
Monitor (A)
To printer port (LTP1)
To video card
- - - - - - - - - - - - - - - ->
Connect to Mains cord at this moment.
Connect to Mains cord
2. Press the AUTO to run the program,the firmware be updated as shown in Fig7`Fig.8
Video cable
Fig.2
ISP box
6. Run the Easywriter program Step 1 : Make a folder in your PC as shown in Fig. 3. For example : C:\easywrite Step 2 : Copy ISP Software Easywriter.zip into your folder as shown in Fig.3. Step 3 : Unzip Easywriter.zip into your folder as shown in Fig. 3. Step 4 : Double click the EasywriterV2.07.exe icon to run the Application as Fig. 4. Fig. 7
170S5
9
Fig.8
34
Magnavox LCD TV Go to cover page
ISP Instruction
Press the file
exit to end program, as shown in Fig.9
Fig.9
If there is a warring message coming as shown in Fig 10. , you have to check the AC power, Video cable, or Novatek MCU.
Magnavox LCD TV
35
BLOCK DIAGRAM
Go to cover page
Go to cover page
Go to cover page
Go to cover page
Go to cover page
40 Go to cover page
Go to cover page
Go to cover page
Go to cover page
Go to cover page
Go to cover page
Go to cover page
47 Go to cover page
48 Go to cover page
49 Go to cover page
Go to cover page
Go to cover page
Go to cover page
Go to cover page
Go to cover page
55 Go to cover page
Go to cover page
823827717261 DC-AC INVERTER(LIVP-2001A) 823827717271 DC-AC INVERTER(LIVP-2001 A) 1183 313815414981 DOOR-CABLE 41
313815860881 KEY BOARD ASSY 1180
313815414931 CONTROL BUTTON
313815862151 MAIN FRAME+WIRE ASSY 313815862291 MAIN FRAME+WIRE ASSY
1054
91
40 1051 1050 93 313815414881 BACK COVER
Exploded View
7 313815758301 BASE ASSY
11
313815758281 BEZEL ASSY
1053
1185
823827717371 LCD LC150X02(series) 823827717471 TFT-LCD MOD T150XG01 V_0(AUO0)
3138 15136441 SHIELD SCALER 313815860781 SCALER PCB ASSY(NAFT)15"LPL 313815862131 SCALER PCB ASSY(NAFT)15"AUO
313815860811 IR PCB ASSY
823827717441 LSP BOX8R3W-L/R(P150B)
Magnavox LCD TV
Go to cover page
58
Magnavox LCD TV Go to cover page
0011 0030 0031 0032 0007 0040 0090 0091 0092 7901 6901 6901 6902 6902 6001 6002 6003 6006 6101 6201 6202 7001 7002 7003 7004 7005 7006 7009 7011 7012 7101 7102 7151 7201 7202 7301 7301 7302 7303 7304 7305 7305 7401 7402 7403 7404 7502 7501 7621 7622 7623
313815758281 313815414871 313815414921 313815414911 313815758301 313815414881 313815523361 313815414931 313815522331 932217439685 313815862261 932220313667 313815862171 932214603682 932221745685 932220347685 932221745685 933913910115 933913910115 933913910115 933913910115 932219076668 932217438685 932217438685 932219076668 932217438685 932216638668 932217438685 932217438685 932216638668 932219412671 933714830653 932222035668 935245720165 932216972682 313815862181 823827716771 932217438685 932219183685 932222076668 313815862211 932218650682 932222013671 932222075668 932222076668 932222076668 932216677682 932216677682 935276561518 932222077668 932222076668
BEZEL ASSY BEZEL LENS-IR POWER BUTTON BASE ASSY BACK COVER PLASTIC COVER CONTROL BUTTON SMART TIPS-WALL MOUNTING TRA SIG SM BC857C (KEC0) R IR + HOLDER ASSY IR RECEIVER TSOP34136SB1 L LED + HOLDER ASSY LED VS L-3WYGW (KIEL) B DIO REC SM SSA34 (VISH) R DIO REG SM BZX84-B16 (VISH) R DIO REC SM SSA34 (VISH) R DIO SIG SM BAS32L (PHSE) R DIO SIG SM BAS32L (PHSE) R DIO SIG SM BAS32L (PHSE) R DIO SIG SM BAS32L (PHSE) R IC SM L5972D (ST00) R TRA SIG SM BC847C (KEC0) R TRA SIG SM BC847C (KEC0) R IC SM L5972D (ST00) R TRA SIG SM BC847C (KEC0) R FET POW SM SI5441DC-E3 (VISH)R TRA SIG SM BC847C (KEC0) R TRA SIG SM BC847C (KEC0) R FET POW SM SI5441DC-E3 (VISH)R IC SM MSP3445G-QI-B8V3(MIAS) Y IC SM 74HC4052D (PHSE) R IC SM TPA3005D2PHP (TI00) R IC SM 74HCT1G14GW (PHSE) R IC SM AT24C02N-10SC-2.7(ATME)L CPU ASSY (LPL -F1 15") NT68F632AL CPU TRA SIG SM BC847C (KEC0) R IC SM LM809M3-2.93 NOPB(NSC0)R IC SM AME1117CCGTZ (ST00) R EEPROM ASSY (LPL-F1 15") IC AT24C16A-10PI-2.7 (ATME) L IC SM MST51512L-LF (MSTA) Y IC SM AME1117BCGTZ (ST00) R IC SM AME1117CCGTZ (ST00) R IC SM AME1117CCGTZ (ST00) R IC SM M12L16161A-7T (ESMT) L IC SM M12L16161A-7T (ESMT) L IC SM SAA7119E/V2/G (PHSE) R IC SM AME1117ECGTZ (ST00) R IC SM AME1117CCGTZ (ST00) R
Magnavox LCD TV
59
Go to cover page
Model: 15MF605T/17 Mechanical parts 0011 313815758281 0030 313815414871 0031 313815414921 0032 313815414911 0007 313815758301 0040 313815414881 0090 313815523361 0091 313815414931 0092 313815522331 LCD Panel 1050 823827717371 PACKING 0450 313815639351 0451 313815639341 0452 313815639331 0453 313815621481 0458 313815636361 Accessory Assessory 4444 313810610443 4444 313810610444 0291 313815565881 0615 313811708201 0292 313815565881 0145 313815523431 0041 313815414891 PCB ASSY 1051 313815860781 1052 313815860801 1053 313815860811 1054 313815860881 Miscellanea 1305 243803100435 8175 313819874531 1001 242202518821 1002 242208611053 1003 242202605309 1101 242254301364 1151 242202518888 1152 313816877251 1153 242202518894 1201 242202518053 1211 243803100429 1251 242202518817 1253 242202605451 1254 242202605452 1301 823827716691 1302 242202518818 1303 242202518894 1401 243854300086 1501 313815862241 1172 313818870491 1175 908210090002 1176 823827717511 1177 313818876621 1180 313815862151 8161 313819874541 1183 823827717261 1184 823827717461 1185 823827717441 8174 313819874571 8176 313819874581 1551 242202505567 1601 313914722661 1621 243854300089 PCB ASSY 1051 2001 2002 2009 2113 2121 2122 2131 2132 2133 2134 313815860781 SCALER PCB ASSY (NAFT)15"LPL 223858619812 223858619812 223891619849 222224119876 223886715159 223886715159 222224119876 223878615649 223878615649 223878615649 CER2 0603 Y5V 50V 100N P8020 R CER2 0603 Y5V 50V 100N P8020 R CER2 0603 Y5V 25V 100N P8020 R CER2 1206 Y5V 10V 10U P8020 R CER1 0603 NP0 50V 15P PM5 R CER1 0603 NP0 50V 15P PM5 R CER2 1206 Y5V 10V 10U P8020 R CER2 0603 X7R 16V 100N PM10 R CER2 0603 X7R 16V 100N PM10 R CER2 0603 X7R 16V 100N PM10 R 2135 2152 2154 2155 2156 2157 2169 2172 2173 2174 2176 2181 2182 2186 2187 2191 2194 2201 2209 2211 2212 2213 2214 2215 2251 2252 2253 2254 2255 2256 2257 2258 2259 2261 2262 2302 2303 2304 2306 2317 2318 2321 2322 2415 2416 2417 2418 2421 2425 2426 2431 2432 2433 2434 2435 2436 2437 2438 2441 2442 2443 2444 2445 2446 2447 2452 2453 2454 2455 2456 2457 2458 2655 2658 2461 2462 2463 2464 2465 2466 2501 2502 2504 223878615649 223891619849 223886715101 223858119716 223886715101 223891619849 223891619849 223886715101 223858119716 223886715101 223891619849 223886115221 223878615649 223891619849 223891619849 223891619849 223891619849 223878615649 223878615649 223886715331 223886715331 223886715331 223886715331 222224119876 223886715331 223886715331 223886715101 223886715331 223886715331 223886715331 223886715331 223886715101 223886715229 223886715101 223886715229 223878615649 223886715229 223886715229 223886715109 223878615649 223878615649 223886715229 223886715229 223858615636 223878615649 223886715229 223886715229 223878615649 223878615649 222224119876 222224119876 223878615649 223878615649 223878615649 223878615649 223878615649 223878615649 223878615649 222224119876 223878615649 223878615649 223878615649 223878615649 223878615649 223878615649 223878615649 223878615649 223878615649 223878615649 222224119876 223878615649 223878615649 223878615649 223878616641 222224119876 223878615649 223878619854 223878619854 223878619854 223878619854 223878615649 223878615649 223878615649 CER2 0603 X7R 16V 100N PM10 R CER2 0603 Y5V 25V 100N P8020 R CER1 0603 NP0 50V 100P PM5 R CER2 1206 Y5V 50V 470N PM20 R CER1 0603 NP0 50V 100P PM5 R CER2 0603 Y5V 25V 100N P8020 R CER2 0603 Y5V 25V 100N P8020 R CER1 0603 NP0 50V 100P PM5 R CER2 1206 Y5V 50V 470N PM20 R CER1 0603 NP0 50V 100P PM5 R CER2 0603 Y5V 25V 100N P8020 R CER1 0805 NP0 50V 220P PM5 R CER2 0603 X7R 16V 100N PM10 R CER2 0603 Y5V 25V 100N P8020 R CER2 0603 Y5V 25V 100N P8020 R CER2 0603 Y5V 25V 100N P8020 R CER2 0603 Y5V 25V 100N P8020 R CER2 0603 X7R 16V 100N PM10 R CER2 0603 X7R 16V 100N PM10 R CER1 0603 NP0 50V 330P PM5 R CER1 0603 NP0 50V 330P PM5 R CER1 0603 NP0 50V 330P PM5 R CER1 0603 NP0 50V 330P PM5 R CER2 1206 Y5V 10V 10U P8020 R CER1 0603 NP0 50V 330P PM5 R CER1 0603 NP0 50V 330P PM5 R CER1 0603 NP0 50V 100P PM5 R CER1 0603 NP0 50V 330P PM5 R CER1 0603 NP0 50V 330P PM5 R CER1 0603 NP0 50V 330P PM5 R CER1 0603 NP0 50V 330P PM5 R CER1 0603 NP0 50V 100P PM5 R CER1 0603 NP0 50V 22P PM5 R CER1 0603 NP0 50V 100P PM5 R CER1 0603 NP0 50V 22P PM5 R CER2 0603 X7R 16V 100N PM10 R CER1 0603 NP0 50V 22P PM5 R CER1 0603 NP0 50V 22P PM5 R CER1 0603 NP0 50V 10P PM5 R CER2 0603 X7R 16V 100N PM10 R CER2 0603 X7R 16V 100N PM10 R CER1 0603 NP0 50V 22P PM5 R CER1 0603 NP0 50V 22P PM5 R CER2 0603 X7R 50V 10N PM10 R CER2 0603 X7R 16V 100N PM10 R CER1 0603 NP0 50V 22P PM5 R CER1 0603 NP0 50V 22P PM5 R CER2 0603 X7R 16V 100N PM10 R CER2 0603 X7R 16V 100N PM10 R CER2 1206 Y5V 10V 10U P8020 R CER2 1206 Y5V 10V 10U P8020 R CER2 0603 X7R 16V 100N PM10 R CER2 0603 X7R 16V 100N PM10 R CER2 0603 X7R 16V 100N PM10 R CER2 0603 X7R 16V 100N PM10 R CER2 0603 X7R 16V 100N PM10 R CER2 0603 X7R 16V 100N PM10 R CER2 0603 X7R 16V 100N PM10 R CER2 1206 Y5V 10V 10U P8020 R CER2 0603 X7R 16V 100N PM10 R CER2 0603 X7R 16V 100N PM10 R CER2 0603 X7R 16V 100N PM10 R CER2 0603 X7R 16V 100N PM10 R CER2 0603 X7R 16V 100N PM10 R CER2 0603 X7R 16V 100N PM10 R CER2 0603 X7R 16V 100N PM10 R CER2 0603 X7R 16V 100N PM10 R CER2 0603 X7R 16V 100N PM10 R CER2 0603 X7R 16V 100N PM10 R CER2 1206 Y5V 10V 1