Text preview for : List_of_Adjustment_Items.pdf part of Mitsubishi VS-50805, WT-60805, WS-55905, WS-65905, WS-73905, WS-55805, WT-46805 Mitsubishi VS-50805, WT-60805, WS-55905, WS-65905, WS-73905, WS-55805, WT-46805 (Chassis V16 N W) (Training Manual + Schematic)
Back to : Mitsubishi VS-50805, 6080 | Home
MODELS: VS-50805 / VS-60805 / WT-46805 / WS-55805 / WS-55905 / WS-65905 / WS-73905 E2PROM Replacement
IC704 stores the adjustment data. After replacing the IC, set the data to the values given in the following tables. If good performance is not obtained, perform the Adjustments Procedures given in the Notes column.
List of Adjustment Items.
Function Display Adjustment Item # Abbrev. Description 1 SCT Picture Gain Control 2 SBRT Sub Brightness 3 SCOL Sub Color 4 STIN Sub Tint 5 SCON Sub Contrast 6 RDRH R-Drive (high) 7 GDR G-Drive 8 BDRH B-Drive (high) 9 CTRH R-Cutoff (high) 10 CTGH G-Cutoff (high) 11 CTBH B-Cutoff (high) 12 RDRL R-Drive (low) 13 BDRL B-Drive (low) 14 CTRL R-Cutoff (low) 15 CTGL G-Cutoff (low) 16 CTBL B-Cutoff (low) 17 GMMA Gamma control 18 BRT Brightness control 19 COL Color Gain control 20 TINT Tint Control 21 CONT Picture Gain control 22 SHRP Sharpness control 23 SSH1 Sub Sharpness for NT 24 SHF1 Sharpness F0 for NT 25 PROV Pre/Overshoot Gain 26 LTI Y Edge Enhancement Level 27 DCOL Dynamic Color 28 CTIL CTI Level 29 ACL ABL mode 30 ACLL ACL level 31 PACL Peak ACL detect 32 DPIC Dynamic Picture 33 DCT DC Restoration 34 LMT Peak Limit level 35 AKB AKB On 36 AKBT AKB Timing Pulse 36 37 BLK Hor/Vert Blank level 38 BLKB RGB Blank bottom level 39 CLMP Clamp Pulse select 40 CLMW Clamp Width 41 SEPA H Sync Separator mode 42 SYNC Sync Detect mode 43 VSYN V Sync Separator T/C 44 HSSW HS Pulse width (Continued on next page)
VIDEO / CHROMA Function
IC2B00 (CXA2101Q) Initial Data Notes NTSC HD 480P 42 Sub Contrast 18 Black Level 2 2 2 Preset 7 10 7 " 2 2 2 " 42 42 White Balance 50 50 Preset 42 42 White Balance 15 15 " 50 50 Preset 15 15 White Balance 50 " 25 " 23 " 50 " 10 " 8 4 5 Preset 31 User 31 User 31 User 42 Preset 31 31 User 2 3 3 Preset 0 3 3 " 3 1 1 " 2 2 2 " 1 1 1 " 3 3 3 " 0 " 0 " 8 " 1 1 User 1 1 Preset 3 3 " 0 " 0 1 0 " 0 " 0~1 0 " 0~15 0 " 0~1 0 " 0~3 0 " 0~1 0 0 0 " 0~3 1 1 3 " 0~3 2 " 0~3 0 " () Automatically goes to value on the left Indicates V16W Only Data Range 0~63 0~63 0~15 0~15 0~15 0~63 0~63 0~63 0~63 0~63 0~63 0~63 0~63 0~63 0~63 0~63 0~15 0~63 0~63 0~63 0~63 0~63 0~3 0~3 0~3 0~3 0~1 0~3 0~3 0~3 0~15 0~3 0~3 0~3 0~1 0~1
Page 26
MODELS: VS-50805 / VS-60805 / WT-46805 / WS-55805 / WS-55905 / WS-65905 / WS-73905 VIDEO / CHROMA Function (Continued)
Function Display Item # Abbrev. 45 HDTC 46 HSBL 47 HSSW 48 IN-1 49 MAT 50 IN-2 51 MODE 52 VM 53 VMDL 54 YSM1 55 VMSW 56 CRO1 57 CBO1 58 CRO2 59 CB02 60 R-YR 61 R-YB 62 G-YR 63 G-YB 64 PON 65 RON 66 GON 67 BON 68 AG-1 69 AG-2 70 OSDL Adjustment Description HDTV Sync T/C HS mask on VS Input Sync select Input select-1 Matrix mode Input select-2 Input Signal mode VM Level VM Delay timing YS/YM-1 On/Off SVM On/Off by YS/YM CR Offset 1 CB Offset 1 CR offset 2 CB Offset 2 R-Y Gain of R-Y R-Y Gain of B-Y G-Y Gain of R-Y G-Y Gain of B-Y RGB On R On G On B On White Aging On /Off Black Aging On/Off OSD Level Data Initial Data Notes Range NTSC HD 480P 0~1 1 1 " 0~1 0 0~1 0 0 0 Preset 0~3 3 3 0 User 0~3 2 2 0 " 0~1 0 1 1 " 0~3 1 3 Preset 0~3 2 2 2 " 0~3 2 2 2 " 0~1 0 " 0~1 1 " 0~15 9 9 9 Cb Cr Offset 0~15 10 10 10 Cb Cr Offset 0~15 7 7 7 Preset 0~15 7 7 7 " 0~15 3 7 3 " 0~15 12 2 12 " 0~15 4 8 4 " 0~15 6 11 6 " 0~1 1 " 0~1 1 " 0~1 1 " 0~1 1 " 0~1 0 " 0~1 0 " 0~15 0 " () Automatically goes to value on the left Indicates V16W Only
AUDIO Function
Function Display Item # Abbrev. 1 AGC 2 MON 3 SUR 4 VMX
Adjustment Description Auto Gain Control On/Off Simulated Stereo Surround Effect Vocal mix (added mid freq boost)
Data Range 0~1 0~15 0~15 0~15
Initial Data 0 8 8 8
IC300 (CXA2022S) Notes MCS Check " " "
AUTO PICTURE Function
Function Display Item # Abbrev. 1 AT1 2 AT2 3 STW 4 STM 5 STS 6 CTW 7 CTM 8 CTS
Adjustment Description AGC Threshold between Strong/Middle AGC Threshold between Middle/Weak Sharpness Target for Weak Signal Sharpness Target for Middle Signal Sharpness Target for Strong Signal Color Target for Weak Signal Color Target for Middle Signal Color Target for Strong Signal
Data Range 0-225 0-225 0-63 0-63 0-63 0-63 0-63 0-63
Initial Data 160 190 16 24 31 20 26 31
Notes Preset " " " " " " "
Page 27
MODELS: VS-50805 / VS-60805 / WT-46805 / WS-55805 / WS-55905 / WS-65905 / WS-73905
DEFL JUNGLE Function
IC4A01 (CXA2102Q) V16N Data V16W 55/65/73" V16W 46" Notes HD NTSC HD NTSC HD NTSC 34 39 40 44 38 44 Width 35 36 40 36 30 25 Preset 47 55 25 25 31 25 " 42 42 40 40 40 40 " 36 54 31 20 27 20 " 34 34 38 34 38 34 " 16 16 31 40 21 31 Height 0 0 0 0 0 0 V Lin. 7 7 7 7 7 7 Preset 0 0 0 0 0 0 " 0 0 0 0 0 0 " 0 0 0 0 0 0 " 1 1 1 1 1 1 " 33 33 34 34 34 34 " 14 19 14 19 14 19 " 50 31 50 31 50 31 " 42 16 24 16 24 16 " 29 16 14 16 14 16 " 31 17 17 17 17 17 " 31 31 31 31 31 31 " 31 31 31 31 31 31 " 7 7 7 7 7 7 " 0 0 0 0 0 0 " 1 1 1 1 1 1 " 7 7 7 7 7 7 " 7 7 7 7 7 7 " 0 0 0 0 0 0 " 0 0 0 0 0 0 " 18 0 0 0 0 0 " 1 0 0 0 0 0 " 0 0 0 0 0 0 " 1 1 1 1 1 1 " 2 2 2 2 2 2 " 0 0 0 0 0 0 " 141 164 141 164 141 164 " 0 0 0 0 0 0 " 8 4 8 4 8 4 " 0 0 0 0 0 0 " 7 7 7 7 7 7 " 1 1 1 1 1 1 " 1 1 1 1 1 1 " 31 31 31 31 31 31 "
Data Range 0-255 0-255 0-63 0-63 0-63 0-63 0-63 0-63 Initial Data 90 180 3 7 63 37 33 31 Notes Preset " " " " " " "
Function Display Item # Abbrev. 1 HWID 2 HKEY 3 EWPT 4 EWCT 5 EWPB 6 EWCB 7 VHGT 8 VLIN 9 VSCN 10 VLNT 11 VLNB 12 AFCR 13 AFCG 14 HPOS 15 BLKL 16 BLKR 17 BLKT 18 BLKB 19 VTIM 20 VPOS 21 SCRL 22 CLP 23 HBSW 24 VBW 25 AFCC 26 EWCM 27 VCOM 28 ZMSW 29 ASPT 30 JPSW 31 ITMD 32 ZCUT 33 VFRQ 34 VFRE 35 MXLN 36 NONI 37 HFRQ 38 FHSW 39 FHAD 40 HSSW 41 VPOF 43 BOW
Adjustment Description Horizontal Width Horizontal Keystone EW-PCC on top EW -PCC top corner EW-PCC on bottom EW-PCC bottom corner Vertical Height Vertical Linearity Vertical S-Correction Vertical Linearity on top Vertical Linearity on bottom AFC Range AFC Loop Gain Horizontal Postion Blanking on left side Blanking on right side Blanking on top Blanking on bottom AKB Timing Vertical Position Vertical Scroll Clamp Pulse Phase HBLK Control Switch Vertical Blanking Switch AFC HV Compensation EW-PCC HV Compensation Verical HV Compensation Zoom Mode Aspect Ration Jump Mode Switch Interlace Mode Switch Eliminate Jitter Vertical Frequency Free Run Setting Free Run Line Number Free Run Scan Mode Horizontal Frequency Control Horizontal Frequency Range Horizontal Frequency Adjust HSYNC/CLP Switch Vertical Protect Switch Bow
Data Range 0~63 0~63 0~63 0~63 0~63 0~63 0~63 0~15 0~15 0~15 0~15 0~1 0~3 0~63 0~63 0~63 0~127 0~127 0~127 0~63 0~63 0~15 0~1 0~1 0~15 0~15 0~15 0~1 0~63 0~1 0~3 0~1 0~15 0~1 0~255 0~1 0~255 0~1 0~15 0~1 0~1 0~63
IRIS Function
Function Display Item # Abbrev. 1 0T1 2 1T2 3 CN0 4 CN1 5 CN2 6 BRO 7 BR1 8 BR2
Adjustment Description Lower thresh hold voltage setting Higher thresh hold voltage setting Low contrast setting Middle contrast setting High contrast setting Low brightness setting Middle brightness setting High brightness setting
Page 28
MODELS: VS-50805 / VS-60805 / WT-46805 / WS-55805 / WS-55905 / WS-65905 / WS-73905
Function Display Adjustment Description Item # Abbrev. 1 1DOT 2DYC 1-kine dot reduct. On/Off 2 VLMT Vert. Enhancement Limit Level 3 VGN Vert. Enhancement Gain 4 VCOR Vert. Enhancement Corring Amplitude 5 GNCP 1-line Gain Compensation 6 2DON 2DYC Sep. Control in SVHS in mode. 7 STFR Y/C Sep. when fsc/fh are not standard 8 ER2F Edge sensitivity detection in two frames (Y and C) 9 ER1F Edge sensitivity detection in one frame (Y and C) 10 VCLP Black clip level by vertical enhancement 11 HHON Sets HH playback mode 12 HHST Sets EDTV2 mode 13 STDI Time constant for fsc/fh standard detection 14 S2NX Time constant for fsc/fh standard detection (stnd to non) 15 N2SX Time constant for fsc/fh standard detection (non to stnd) 16 HMEN Internal H mask pulse end phase 17 HMST Internal H mask pulse start phase 18 VINV Polarity of vert. sync input (pin 58) 19 KINV Polarity of color killer control input (pin 8) 20 CLON Clamping control (VCR skew countermeasure) 21 CLDA Set when clamp control is OFF 22 ACPE Analog clamp pulse end phase 23 ACPO Internal clamp pulse On/Off (ext. out, pin 61) 24 ACPI Analog clamp pulse logic (pin 61) 25 ACPS Analog clamp pulse start phase (HREF as reference) 26 HBLE Internal H blanking pulse end phase 27 FREE Controls H-PLL operation for CD generation 28 HBLS Internal H blanking pulse start phase (HREF as ref.) 29 BFPS Internal burst flag puls start phase 30 XHBE H blanking end phase for ext. out (pin 60) 31 XHBS H blanking start phase for ext. out (pin 60) 32 VLPH Latch phase of vertical sync signal (pin 58) 33 VRPH Vertical reference phase 34 XBLK Ouput blanking for ext. out (pin 60) 35 VBLE Vertical blanking end phase 36 BVBLS Vertical blanking start phase 37 STON ON/OFF of standard detection by phase comp. out level 38 STDA Data at STDCON forced setting 39 HVST Cont. detection level of H/V standard detection 40 STPH Standard Detection Reference level for phase compare output 41 XVBL On/Off of vert. blank output (pin 60) 42 MD10 ON/OFF of motion detection in one frame for Y 43 MD20 ON/OFF of motion detection in two frames for Y 44 YCSP SVHS input mode 45 MDHS Y Motion detect level adjust. for H edge portion in one frame 46 MD1F Offset for motion detection in one frame for Y (flat part) 47 MD1E Offset for motion detection in one frame for Y (edge part) 48 CCDF Offset for motion detection in two frames for C (flat part) 49 CCDE Offset for motion detection in two frames for C (edge part) 50 MD2F Offset for motion detection in two frames for C (flat part) 51 MD2E Offset for motion detection in two frames for C (edge part) (Continued on next page)
Page 29
3DYC Function
IC2000 (TC90A28F) Data Initial Notes Range Data 0~1 0 Preset 0~31 2 " 0~7 1 " 0~7 5 " 0~1 0 " 0~1 0 " 0~1 1 " 0~15 7 " 0~15 7 " 0~15 11 " 0~1 1 " 0~1 0 " 0~3 3 " 0~1 1 " 0~1 0 " 0~31 5 " 0~31 14 " 0~1 0 " 0~1 0 " 0~1 1 " 0~1 1 " 0~63 14 " 0~1 0 " 0~1 0 " 0~63 24 " 0~127 50 " 0~1 0 " 0~127 113 " 0~127 52 " 0~127 34 " 0~127 97 " 0~15 6 " 0~511 247 " 0~1 1 " 0~31 23 " 0~63 21 " 0~1 0 " 0~1 0 " 0~7 4 " 0~63 19 " 0~1 0 " 0~1 1 " 0~1 1 " 0~1 0 " 0~1 1 " 0~15 6 " 0~15 6 " 0~15 5 " 0~15 5 " 0~15 4 " 0~15 4 "
MODELS: VS-50805 / VS-60805 / WT-46805 / WS-55805 / WS-55905 / WS-65905 / WS-73905 3DYC Function (continued)
Function Display Adjustment Description Item # Abbrev. 52 B22H Controls output of identification line 53 BSCR BS coring level (dispersal countermeasure) 54 CCR1 Cross color reduction register 1 55 CCR2 Cross color reduction register 2 56 ENCH Polarity of external memory read/write enable 57 ENDL Delay of external memory read/write enable 58 WDLY Fine phase adj. of external memory write enable 59 HDLY Phase adjust of internal H reset (HREF as reference) 60 RSTH Polarity of reset to external memory 61 RDLY Fine phase adj. of external memory read enable 62 VDLY Internal V reset phase adj. 63 PSTD MUSE/NTSC converter mode setting 64 EVSL V blank phase adj. for EDTV2 65 ED47 (16/7)fsc APC time constant 66 EDAP Amplitude reference for EDTV2 ID 67 EDTM Reference for detecting EDTV2 68 EDPH ON/OFF phase error correction for detection EDTV2 ID 69 BCNT Adjust timing generator phase for EDTV2 ID 70 CBPF ON/OFF of BPF at SVHS-C output 71 SDRG Reference for fsc/fH standard detection (standard to non) 72 SDON Reference for fsc/fH standard detection (non to standard) 73 MDFS Motion detection sensitivity in two frames for Y (flat part) 74 CCDE Motion detection sensitivity in two frames for Y (edge part) 75 HHGN HH signal gain adjustment 76 HHCR HH signal coring adjustment 77 PCBO Offset for HH/C signal separation 78 NSTL Non-standard detect Level for fsc/fv standard detection 79 DISP Dispersal countermeasure 80 HSTD Standard detect level for fsc/fv standard detection 81 HSTU Non-standard detect Level for fsc/fv standard detection 82 S7SW Integration range for (4/7)fsc demodulation in-phase comp. 83 SDHR H/V standard detect result in fsc/fH standard detection 84 NDCE Error level in DC level detect at EDTV2 ID 85 CDLY Adjust C output delay 86 NBYE Error level in fsc demodulation burst axis at EDTV2 ID 87 NS7E Error level in (4/7)fsc demodulation in-phase at EDTV2 ID 88 DOS7 Select mode for (4/7)fsc demodulation in-phase detection 89 VS7 Forced setting for (4/7)fsc demodulation in-phase, DOS7=1 90 DOBY Select mode for fsc demodulation burst axis level detection 91 VBY Forced setting for (4/7)fsc burst axis level, DOBY=1 92 DODC Select mode for DC level at EDTV2 ID 93 VDC Forced setting for DC level at EDTV2 ID 94 DNRZ Select mode for NRZ det. at EDTV2 ID 95 VNRZ Forced setting for NRZ at EDTV2 ID 96 OFHH HH addition control at EDTV2 (on to off) 97 ONHH HH addition control at EDTV2 (off to on) 98 UVBY Ref. for level comparison upper fsc demod. in-phase 99 LVBY Ref. for level comparison lower fsc demod. in-phase 100 UV7S Ref. for level comparison upper (4/7)fsc demod. in-phase 101 LV7S Ref. for level comparison lower (4/7)fsc demod. in-phase 102 UNRZ Ref. for level comp. upper DC integr. (NRZ part) (Continued on next page)
Page 30
Data Initial Range Data 0~1 0 0~15 0 0~255 6 0~255 6 0~1 0 0~1 1 0~15 1 0~1023 54 0~1 0 0~15 4 0~1023 242 0~1 0 0~3 2 0~3 0 0~15 6 0~255 2 0~1 0 0~63 41 0~1 1 0~63 10 0~63 6 0~1 0 0~1 0 0~7 2 0~15 3 0~15 6 0~255 12 0~1 1 0~127 6 0~127 13 0~1 0 0~1 1 0~7 3 0~3 0 0~7 4 0~7 2 0~1 0 0~1 0 0~1 0 0~1 0 0~1 0 0~1 0 0~1 0 0~1 0 0~7 4 0~7 6 0~15 11 0~15 12 0~15 11 0~15 0 0~15 3
Notes Preset " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " "
MODELS: VS-50805 / VS-60805 / WT-46805 / WS-55805 / WS-55905 / WS-65905 / WS-73905 3DYC Function (continued)
Function Display Item # Abbrev. 103 LNRZ 104 UVDC 105 LVDC 106 VEDG 107 YCIN 108 SLIS 109 NRZB 110 HHAC 111 DCRC 112 VCRC 113 PCMB 114 COMB 115 AFMD 116 INRZ 117 CRCB 118 DOHH 119 VHH 120 HBEP 121 HBSP 122 MNC1 123 MNC2 124 OKIM 125 LINE 126 HREF 127 SWTM 128 RRST 129 LEAK 130 22ID 131 MDFC 132 MDEC 133 TL3D Adjustment Description Data Initial Range Data 0~15 5 0~15 11 0~15 11 0~15 8 0~1 0 0~15 0 0~1 0 0~1 1 0~1 0 0~1 0 0~1 0 0~1 0 0~1 1 0~1 0 0~1 0 0~1 0 0~1 0 0~7 5 0~31 16 0~1 0 0~1 0 0~1 1 0~1 0 0~1 0 0~3 2 0~3 0 0~1 1 0~1 1 0~15 6 0~15 6 0~7 4 Notes Preset " " " " " " " " " " " " " " " " " " " " " " " " " " " " " "
Ref. for level comp. lower DC integr. (NRZ part) Ref. for level comp. upper DC integr. (NRZ part) Ref. for level comp. lower DC integr. (NRZ part) Cross color reduction countermeasure SVHS input mode setting 2 Adj. offset of NRZ slice level Target bits for NRZ slice level offset adj. Condition for HH addition control CTC error detection Forced setting for CRC error det. (DOCRC=1) Pre-combing operation Forced setting for pre-combing Operation mode NRZ error detection condition Target bits for CRC error detection HH addition control signal/forced operation Forced setting for HH addition control signal End phase fine adj. for horizontal blanking Start phase fine adj. for horizontal blanking ON/OFF mot. det. In one frame for Y at MNC input ON/OFF mot. det. In two frames for Y at MNC input Select external field memory Forced through mode for internal line memory Timing of HREF signal to detect vertical sync signal Timing to switch between line memory and 3DYC Delay time for RRST for ext. FIFO memory ON/OFF control for color leaks improvement Line 22 ID for EDTV2 signal Offset for mot. det. In one frame for C (flat part) Offset for mot. det. In one frame for C (edge part) Timing to switch between line memory and 3DYC
1H LUMINANCE Function
Function Display Item # Abbrev. 1 DELY 2 SHRP 3 8MHZ 4 SRT 5 SRTL 6 LTTR 7 YNR 8 GMM1 9 GMM2 10 BEXP 11 BCMP 12 BDTC 13 VM 14 DAC1 15 DAC2 16 TEST
Adjustment Description Controls ON/OFF of DL APAC Controls sharpness Controls gain of correction at 8MHz Super Real Trans (SRT) On/Off SRT starting level Luminance Transient Tracking Ratio Y noise reduction (YNR) ON/OFF Gamma correction starting point Gamma correction curve characteristic Black expansion ON/OFF Black level compensation ON/OFF Black area detect maximum level Controls gain of SVM Y output signal 1-bit DAC output 1-bit DAC output Pin-20 output signal in test mode
Page 31
Data Range 0-1 0-127 0-7 0-1 0-3 0-7 0-1 0-3 0-1 0-1 0-1 0-3 0-3 0-1 0-1 0-3
IC7310 (TA1226N) Initial Notes Data 1 Preset 25 " 1 " 1 " 0 " 7 " 1 " 3 " 0 " 0 " 0 " 0 " 0 " 0 " 0 " 3 "
MODELS: VS-50805 / VS-60805 / WT-46805 / WS-55805 / WS-55905 / WS-65905 / WS-73905 2H LUMINANCE Function
Function Display Item # Abbrev. 1 PEAK 2 STEP 3 LWC 4 COR 5 STB 6 AMS 7 FHS 8 CFS Adjustment Description Peaking amplitude control Transient step control Line width control Coring level control Standby bit Y-input amplitude selection Line frequency selection Contour Filter selection Data Range 0-63 0-63 0-63 0-63 0-1 0-1 0-1 0-1 IC2D00 (TDA9177) Initial Notes Data 45 Preset 55 " 63 " 7 User 1 Preset 1 " 1 " 1 "
PTC CONTROL Function
Function Display Item # Abbrev. 1 E0F 2 ELN 3 MOF 4 MLN 5 FMC 6 FSC 7 YLVL 8 HENA 9 HENB 10 VEN 11 FIL 12 MDET 13 CCNT 14 CCTC 15 CCTD 16 MUX 17 COR
Adjustment Description Edge Detection Offset Endge Detection Sensitivity Monitor Detection Offset Monitor Detection Sensitivity Quantity of Moving Pixel Quantity of Still Pixel Y Level for Enhacer Horizontal Enhance 2 Gain Horizontal Enhance 1 Gain Vertical enhance Gain Interpolation Filter Monitor Detection for Black Achroma Adjust On/Off Chroma Adjust c Chroma Adjust d Chroma MPX On/Off Coring Level
Data Range 0~15 0~15 0~31 0~7 0~15 0~15 0~3 0~3 0~3 0~3 0~1 0~1 0~1 0~1 0~1 0~1 0~3
Initial Data 15 6 23 5 1 15 2 3 0 2 0 0 0 0 0 1 1
Notes Preset " " " " " " " " " " " " " " " "
Function Display Adjustment Item # Abbrev. Description 1 HPOS Picture Horiz. Position 2 VPOS Picture Vert. Position 3 HS HSYNC Phase Control 4 FS Field Sync Vert. Position 5 FPDS Field Pulse Detect Area Start 6 FPDE Field Pulse Detect Area Stop 7 ICW Input Clamp Pulse Width 8 ICP Input Clamp Pulse Position 9 ICVM Input Clamp Pulse V-mask On 10 BON Blanking Pulse Output On/Off 11 BLKP Horiz. Blank Pluse Pos. for BE 12 BMOD Blanking Output Mode 13 BLKL Blanking Level 14 OEHW OE Horiz. Width for SVP 15 OEHP OE Horiz. Position 16 OEVW OE Vert. Width for SVP 17 OEVS OE Vert. Position (Continued on next page)
Page 32
PTC LOGIC Function
Data Range 0~1023 0~1023 0~1023 0~511 0~31 0~31 0~15 0~1023 0~1 0~1 0~7 0~3 0~15 0~31 0~1023 0~63 0~1023
Initial Data V16N V16W 203 203 11 19 120 120 173 17 13 13 27 27 7 7 72 72 1 1 0 0 0 0 0 1 0 0 0 0 267 267 0 0 0 0
Notes Preset " " " " " " " " " " " " " " " "
MODELS: VS-50805 / VS-60805 / WT-46805 / WS-55805 / WS-55905 / WS-65905 / WS-73905 PTC LOGIC Function (Continued)
Function Display Item # Abbrev. 18 CMPX 19 FS1F 20 VDP 21 FP 22 FPP 23 FDP 25 MODE 26 DSEN 27 ABEN 28 ABDT 29 P3 30 P2 31 P1 32 P0 40 HPO1 41 HPO2 42 VPO1 43 VPO2 44 ICW1 45 ICP1 46 ICW2 47 ICP2 Adjustment Description Chroma MPX Pol. Pos/Neg FSYNC period ½ field VD Pulse Polarity Field Pulse Internal/External Field Pulse Polarity HD Pulse Polarity Display Mode Format Change Auto/Manual Format Change Auto/Manual Abnormal Mode detective time Extension Port #3 Extension Port #2 Extension Port #1 Extension Port #0 Horiz. Position for DVD Horiz. Position for SD Vert. Position for DVD Vert. Position for SD Clamp Width for DVD Clamp Position for DVD Clamp Width for SD Clamp Width for SD Data Range 0~1 0~1 0~1 0~1 0~1 0~1 0~3 0~1 0~1 0~15 0~1 0~1 0~1 0~1 0~1023 0~1023 0~1023 0~1023 0~15 0~1023 0~15 0~1023 Initial Data V16N V16W 0 0 1 1 1 1 0 0 1 0 1 1 0 3 1 1 1 1 0 0 0 0 0 0 0 0 0 0 193 193 193 193 19 19 19 19 1 1 72 72 7 7 72 72 Notes Preset " " " " " " " " " " " " " " " " " " " " "
Function Display Adjustment Item # Abbrev. Description 1 PIP PIP on/off 2 FRM Field/Frame display 3 LDB Line doubled or read once 4 R27 read at 13.5/27(MHz) 5 PLO Internal PLL off 6 FRZ Freeze pip picture 7 SYS System pin activation 8 HPM 2 MSB's of horizontal position 9 MXD Mixed display mode selection 10 SLD Delay of SEL output from PIP 11 HPO Horizontal position 12 VPO Vertical position 13 YDL Delay of Y signal 14 SW1 Switch output 1 15 SW2 Switch output 2 16 IMP Line standard of inset 17 PMD Line standard of parent 18 CHI Chrominance input selection 19 IHV Sync input selection 20 DECH Horizontal decimation (3:1,4:1) 21 DECV Vertical decimation (3:1,4:1) 22 HSD Delay of H-sync 23 CSW Clock source 24 CFX ADC clamp dependence 25 32C Clamp cycles per line 26 VSD Vertical sync delay (Continued on next page) Page 33
PIP Function V16N only
Data Range 0~1 0~1 0~1 0~1 0~1 0~1 0~1 0~3 0~1 0~15 0~255 0~255 0~7 0~3 0~3 0~3 0~3 0~1 0~1 0~1 0~1 0~15 0~1 0~1 0~1 0~31
IC6P00 (SDA9288X) Initial Notes Data 0 Preset 1 " 0 " 0 " 0 " 0 " 0 " 2 " 0 " 1 " 13 " 157 " 2 " 0 " 0 " 2 " 2 " 0 " 0 " 0 " 0 " 15 " 1 " 0 " 0 " 2 " * Must be manually set
MODELS: VS-50805 / VS-60805 / WT-46805 / WS-55805 / WS-55905 / WS-65905 / WS-73905 PIP Function V16N only (continued)
Function Display Item # Abbrev. 27 VSQ 28 ASC 29 VPD 30 VSPQ 31 PARS 32 FRY 33 CON 34 FRU 35 FRV 36 FWH 37 FWV 38 SLD2 39 OFR 40 CHP 41 MT0 42 MT1 43 MT2 44 PLT 45 DAC 46 PDU 47 PDV 48 HSD1 49 HSD2 50 VSD1 51 VSD2 52 VPD1 53 VPD2 Adjustment Description Noise reduction of VSI pulse Amp for decimation filters Delay of parent V-sync pulse Noise reduction of VPI pulse Parent sync input selection Y-component of frame PIP contrast control U-component of frame color V-component of frame color Frame width horizontal Frame width vertical SEL, SELD output selection Output selection Chrominance output selection NTSC matrix selection USA format selection Automatic/Fixed matrix selection PLL time constant damping Output current adjustment Pedestal for U adjust Pedestal for V adjust Delay of inset H-sync (DVD) Delay of inset H-sync (SD) Delay of inset V-sync (DVD) Delay of inset V-sync (SD) Delay of parent V-sync (DVD) Delay of parent V-sync (SD) Data Range 0~1 0~1 0~31 0~1 0~1 0~15 0~15 0~15 0~15 0~7 0~3 0~1 0~1 0~1 0~1 0~1 0~1 0~3 0~1 0~15 0~15 0~15 0~15 0~31 0~31 0~31 0~31 Initial Notes Data 0 " 0 " 0 " 0 " 0 " 0 " 4 " 0 " 0 " 0 " 0 " 1 " 0 " 0 " 1 " 0 " 0 " 2 " 0 " 0* Cr Cb PIP Offset 0* Cr Cb PIP Offset 14 Preset 14 " 6 " 6 " 3 " 3 " * Must be manually set Data Range 0-63 0-63 0-63 0-31 0-31 0-31 0-31 0-15 0-15 0-15 0-15 0-31 0-31 0-63 0-4095 0-7 0-255 0-15 0-3 0-7 0-7 Initial Data 50 42 20 25 23 25 23 8 8 8 8 23 18 15 2751 3 74 5 1 0 0 Notes Preset " " " " " " " " " " " " " " " " " " " "
Function Display Adjustment Item # Abbrev. Description 1 BRTH Brightness maximum limit 2 MBLK Main scalar Y-BLK offset at DVD/SD YPrPb input 3 COR 2H enhancement coring adjustment 4 H1M1 PTC logic HPOS offset at DVD 4:3 mode 5 H1M2 PTC logic HPOS offset at DVD 3:4 mode 6 H2M1 PTC logic HPOS offset at SD YPrPb 4:3 mode 7 H2M2 PTC logic HPOS offset at SD YPrPb 3:4 mode 8 V1M1 PTC logic VHPOS offset at DVD 4:3 mode 9 V1M2 PTC logic VPOS offset at DVD 3:4 mode 10 V2M1 PTC logic VPOS offset at SD YPrPb 4:3 mode 11 V2M2 PTC logic VPOS offset at SD YPrPb 3:4 mode 12 CRX1 Video Chroma CR offset at Doubler Zoom (3:4) mode 13 CBX1 Video Chroma CB offset at Doubler Zoom (3:4) mode 14 DVCF DVD allowed format combination 15 DTCF DTV allowed format combination 16 VHGA Jungle VHGT offset for composite, S-Video and DVD 17 BLKA Jungle BLKB offset at Doubler 4:3 mode 18 GMMA Gamma control for external inputs 19 DCT DC transmission control for external inputs 20 TSR1 Main scalar H position offset at 4:3 SP with DVD/SD 21 TSR2 Main scalar H position offset at DW with DVD/SD (Continued on next page) Page 34
MISC. Function
MODELS: VS-50805 / VS-60805 / WT-46805 / WS-55805 / WS-55905 / WS-65905 / WS-73905 MISC. Function (Continued)
Function Display Item # Abbrev. 22 TSR3 23 TSR4 24 TRPS 25 TRPE 26 PRH1 27 PRH2 28 PRH3 29 WRS1 30 WRS2 31 WRS3 32 WRS4 33 WRS5 34 WRS6 35 WRS7 Adjustment Description Main scalar H position offset at 3POP with DVD/SD Main scalar H position offset at 9POP with DVD/SD Side panel start position offset with DVD/SD Side panel end position offset with DVD/SD PIP window H position offset at DW with DVD/SD PIP window H position offset at 3POP with DVD/SD PIP window H position offset at 9POP with DVD/SD PIP H position offset at DW with SD RGBHV input PIP H position offset at 3POP with SD RGBHV input PIP H position offset at 9POP with SD RGBHV input PIP H position offset at 1/9W with SD RGBHV input PIP H position offset at 1/16W with SD RGBHV input PIP H position offset at 1/9 with SD RGBHV input PIP H position offset at 1/16 with SD RGBHV input Data Range 0-7 0-7 0-7 0-7 0-7 0-7 0-7 0-7 0-7 0-7 0-7 0-7 0-7 0-7 Initial Data 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Notes Preset " " " " " " " " " " " " "
Function Display Adjustment Item # Abbrev. Description 1 TNTM Main Tint 2 COLM Main Color 3 YDRM Main Gain Control 4 VPDM Main-V Pedestal DC Control 5 UPDM Main-U Pedestal DC Control 6 SHPM Main Sharpness 7 SPFM Main Sharpness fo Adjust 8 POVM Main Pre/Over Shoot Ratio 9 YDLM Main Y-Delay 10 DCTM Main DC Transmission Ratio 11 DPCM Black Level Expansion 12 TOTM Main Chroma TOT Filter 13 KILM Main Color Killer Monitor 14 HLKM Main VCO/Sync Monitor 15 FSCM Main fsc Output 16 Y2DM G+ (Y) Gain Control 17 U2PM G+ (U) Pedestal Control 18 V2PM G+ (V) Pedestal Contrl 19 U2DM G+ (U) Gain Control 20 V2DM G+ (V) Gain Control 21 SCNM Sub Contrast Adjustment 22 SCLM Sub Color Adjustment 23 SHUM Sub Tint Adjustment 24 AFCM AFC Loop Gain 25 CDMM V-SYNC Velocity Switch 26 SCRM BGP rise phase for SCP 27 SCFM BGP fall phase for SCP 28 VFQM No signal Vertical Frequency 29 3DCM 3H (bottom & top) to DC Sw. 30 EXTC DET Switch 31 TRPM Chroma Trap 32 TAJM Chroma Trap fo Adjustment 33 XPIN Xtal choice (Continued on next page)
Page 35
MAIN DECODER Function
Data Range 0~63 0~63 0~31 0~15 0~15 0~15 0~1 0~3 0~3 0~7 0~1 0~1 0~1 0~1 0~1 0~31 0~15 0~15 0~31 0~31 0~15 0~15 0~15 0~3 0~1 0~3 0~3 0~3 0~1 0~1 0~1 0~15 0~3
IC2200 (CXA2019AQ) Initial Notes Data 29 Preset 18 " 7 Main Y Level 7 Preset 7 " 5 " 3 " 3 " 0 " 0 " 1 " 0 " Sig. dep. " Sig. dep. " 1 " 30 " 5 " 6 " 15 " 15 " 3 " 4 " 7 " 2 " 0 " 3 " 3 " 0 " 0 " 0 " 0 " 9 " 0 "
MODELS: VS-50805 / VS-60805 / WT-46805 / WS-55805 / WS-55905 / WS-65905 / WS-73905 MAIN DECODER Function (Continued)
Function Display Item # Abbrev. 34 CSYS 35 C-LP 36 CYCM 37 ABL 38 ABLG 39 ABLC 40 VCOF 41 SECA 42 5060 43 NTPL 46 MSKM 47 SCR1 48 SCR2 49 SCF1 50 SCF2 Adjustment Description Color System Select Choice of Color Loop SW to select Input Switch RY-Out ABL Switch ABL Gain Control ABL Center Voltage Control Burst Frequency Monitor SECAM Monitor 50/60 Hertz Monitor NTSC/PAL Monitor Macro-vision Countermeasure SCP Clamp rising edge control (DVD) SCP Clamp rising edge control (SD) SCP Clamp falling edge control (DVD) SCP Clamp falling edge control (SD) Data Range 0~3 0~3 0~1 0~1 0~1 0~3 0~1 0~1 0~1 0~1 0~1 0~3 0~3 0~3 0~3 IC2200 (CXA2019AQ) Initial Notes Data 0 Preset 0 " 1 " 1 " 0 " 0 " " " " " 1 " 3 " 3 " 3 " 3 " IC2300 (CXA2019AQ) Initial Notes Data 29 Sub Picture Tint 19 Sub Color 7 Sub Y Level 7 Preset 7 " 5 " 0 " 3 " 0 " 0 " 1 " 0 " Sig. dep. " Sig. dep. " 1 " 30 " 5 " 6 " 15 " 15 " 3 " 4 " 7 " 2 " 0 " 3 " 3 " 0 " 0 " 0 " 1 "
Function Display Adjustment Item # Abbrev. Description 1 TNTS Sub Tint 2 COLS Sub Color 3 YDRS Sub Gain Control 4 VPDS Sub-V Pedestal DC Control 5 UPDS Sub-U Pedestal DC Control 6 SHPS Sub Sharpness 7 SPFS Sub Sharpness fo Adjust 8 POVS Sub Pre/Over Shoot Ratio 9 YDLS Sub Y-Delay 10 DCTS Sub DC Transmission Ratio 11 DPCS Black Level Expansion 12 TOTS Sub Chroma TOT Filter 13 KILS Sub Color Killer Monitor 14 HLKS Sub VCO/Sync Monitor 15 FSCS Sub fsc Output 16 Y2DS G+ (Y) Gain Control 17 U2PS G+ (U) Pedestal Control 18 V2PS G+ (V) Pedestal Contrl 19 U2DS G+ (U) Gain Control 20 V2DS G+ (V) Gain Control 21 SCNS Sub Contrast Adjustment 22 SCLS Sub Color Adjustment 23 SHUS Sub Tint Adjustment 24 AFCS AFC Loop Gain 25 CDMS V-SYNC Velocity Switch 26 SCRS BGP rise phase for SCP 27 SCFS BGP fall phase for SCP 28 VFQS No signal Vertical Frequency 29 3DCS 3H (bottom & top) to DC Sw. 30 EXTC DET Switch 31 TRPS Chroma Trap (Continued on next page)
Page 36
SUB DECODER Function
Data Range 0~63 0~63 0~31 0~15 0~15 0~15 0~1 0~3 0~3 0~7 0~1 0~1 0~1 0~1 0~1 0~31 0~15 0~15 0~31 0~31 0~15 0~15 0~15 0~3 0~1 0~3 0~3 0~3 0~1 0~1 0~1
MODELS: VS-50805 / VS-60805 / WT-46805 / WS-55805 / WS-55905 / WS-65905 / WS-73905 SUB DECODER Function (Continued)
Function Display Item # Abbrev. 32 TAJS 33 XPIN 34 CSYS 35 C-LP 36 CYCS 37 ABL 38 ABLG 39 ABLC 40 VCOF 41 SECA 42 5060 43 NTPL 46 MSKS Adjustment Description Chroma Trap fo Adjustment Xtal choice Color System Select Choice of Color Loop SW to select Input Switch RY-Out ABL Switch ABL Gain Control ABL Center Voltage Control Burst Frequency Monitor SECAM Monitor 50/60 Hertz Monitor NTSC/PAL Monitor Macro-vision Countermeasure Data Range 0~15 0~3 0~3 0~3 0~1 0~1 0~1 0~3 0~1 0~1 0~1 0~1 0~1 IC2300 (CXA2019AQ) Initial Notes Data 9 Preset 0 " 0 " 0 " 0 " 1 " 0 " 0 " " " " " 1 " IC7000 (TC90A18AF) Initial Notes Data 0 Preset 2047 " 64 " 0 " 32 " 0 " 64 " 0 " 68 " 0 " 71 " 0 " 73 " 0 " 75 " 0 " 76 " 0 " 77 " 0 " 77 " 0 " 76 " 0 " 75 " 0 " 73 " 0 " 71 " 0 " 68 " 0 " 64 " 0 " 58 "
Function Display Data Item # Abbrev. Range 1 UYDL 0-7 2 UCDL 0-7 3 UHPW 0-1 4 UHPG 0-3 5 UYVS 0-1 6 YCLE 0-3 7 UCCL 0-3 8 UVCL 0-3 9 H6LD 0-2047 10 H4LD 0-2047 11 TS22 0-1023 12 TS28 0-1023 13 TSHD 0-2047 14 TSPY 0-1023 15 TSPC 0-1023 16 TSPV 0-1023 17 MSPY 0-63 18 MBLK 0-63 19 MCDY 0-7 20 SPCB 0-31 21 MYDY 0-7 22 MPCA 0-31 26 MBKA 0-31 27 MGTS 0-11 28 MBKB 0-31 29 MGTE 0-511 30 TSCD 0-7 31 TSWS 0-2047 32 TWED 0-15 33 TTPH 0-1 34 THAD 0-2047 35 TSWE 0-2047 36 TKMD 0-3 37 TSRS 0-2047 38 TSDL 0-2047 (Continued on next page)
MAIN SCALAR Function (V16W, NTSC Only)
Initial Data 0 0 0 0 1 1 1 1 0 0 11 273 1310 62 62 24 48 31 0 0 0 0 1 0 0 251 1 0 6 1 64 1278 0 46 44 Notes Preset " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " "
Function Display Item # Abbrev. 39 TRPS 40 TRPE 41 TSHK 42 TPH7 43 TAD0 44 TSB0 45 TAD1 46 TSB1 47 TAD2 48 TSB2 49 TAD3 50 TSB3 51 TAD4 52 TSB4 53 TAD5 54 TSB5 55 TAD6 56 TSB6 57 TAD7 58 TSB7 59 TAD8 60 TSB8 61 TAD9 62 TSB9 63 TADA 64 TSBA 65 TADB 66 TSBB 67 TADC 68 TSBC 69 TADD 70 TSBD 71 TADE 72 TSBE 73 TADF
Data Range 0-2047 0-2047 0-255 0-255 0-255 0-255 0-255 0-255 0-255 0-255 0-255 0-255 0-255 0-255 0-255 0-255 0-255 0-255 0-255 0-255 0-255 0-255 0-255 0-255 0-255 0-255 0-255 0-255 0-255 0-255 0-255 0-255 0-255 0-255 0-255
Page 37
MODELS: VS-50805 / VS-60805 / WT-46805 / WS-55805 / WS-55905 / WS-65905 / WS-73905 MAIN SCALAR Function (V16W, NTSC Only)
Function Display Item # Abbrev. 74 TSBF 75 TRBS 76 TRBE 77 TSPS 78 TSPE 81 CHAD 82 CVPR 83 CHPR 84 CHLE 85 CNRM 86 CHLS 87 CVOE 88 CVOS 89 CVPE 90 CVPS 91 CVLE 92 CVLS 94 LLMT 95 LREF 96 LCBG 97 LYBG 98 LSEL 99 LKKL 100 LGKL 101 LGPS 102 LBUR 103 LVMS 104 LVME 105 BWRF 106 BBRF 107 BWNM 108 BGNM 109 BVST 110 BUOF 111 BEOF 112 VJEN 113 VDSL 114 VUSL 115 VDUM 116 VUUM 117 VUPD 118 VDWD 119 VUSB Data Range 0-255 0-2047 0-2047 0-2047 0-2047 0-1 0-1 0-1 0-2047 0-1 0-2047 0-2047 0-2047 0-2047 0-2047 0-2047 0-2047 0-255 0-255 0-255 0-255 0-3 0-1 0-1 0-1023 0-2047 0-511 0-511 0-255 0-255 0-255 0-255 0-511 0-15 0-15 0-1 0-1 0-1 0-3 0-3 0-511 0-511 0-511 Initial Data 0 161 1286 28 118 0 0 0 0 0 0 0 0 1024 0 0 0 27 12 10 4 3 0 0 96 30 18 249 65 10 50 100 253 3 3 0 0 1 3 0 80 180 60 Notes Preset " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " Function Display Item # Abbrev. 120 VDMV 121 VDST 122 VUMV 123 VUST 124 NMAX 125 NMIN 126 NDIF 127 NREF 128 NSET 129 NSTH 130 NINS 131 NRST 132 NJCL 133 NKLD 134 NEGT 135 NPTM 136 NNTL 137 NJDT 138 NPLJ 139 NKJL 140 NEGM 141 NMXM 142 NKLU 143 NNBL 144 NJCM 145 NMSL 146 NPTL 147 NBKL 148 NJTH 149 NPBL 150 NMON 151 EINT 152 EDCT 153 ENTH 154 EDLY 155 EB35 156 EDSW 157 ENRZ 158 EDCF 160 SCRS 161 SCRD 162 SCRT Data Range 0-15 0-15 0-15 0-15 0-255 0-255 0-255 0-255 0-255 0-7 0-31 0-1 0-1 0-1 0-3 0-3 0-511 0-3 0-1 0-1 0-1 0-1 0-1 0-511 0-1 0-15 0-511 0-7 0-7 0-511 0-1 0-1 0-127 0-255 0-255 0-3 0-1 0-31 0-15 0-127 0-255 0-1 Initial Data 10 4 10 4 47 32 10 20 8 3 5 0 0 0 2 2 30 1 0 0 0 0 0 243 1 3 30 7 7 253 0 0 50 33 98 1 1 16 15 10 30 0 (Continued) Notes Preset " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " "
Page 38
MODELS: VS-50805 / VS-60805 / WT-46805 / WS-55805 / WS-55905 / WS-65905 / WS-73905 SUB SCALAR Function (V16W, NTSC Only)
Function Display Item # Abbrev. 1 YCF1 2 YCF0 3 YCMN 4 C2HF 5 Y2HF 6 WNSL 7 KMOD 8 YDL 9 KTC 10 KD0 11 KD1 12 KD2 13 KD3 14 KD4 16 KD6 17 KD7 19 WCSL 20 PAPF 21 WHST 22 WHMD 23 WXIV 24 WHED 25 WYIV 26 WYDL 27 IEIV 28 KWST 29 WCIV 30 WCDL 31 KWED 32 WHTH 33 WHIV 34 WIV2 35 MOH 36 WRST 37 WKHY 38 WHI1 39 WYI1 40 W263 41 HYJ 42 WCMP 43 RKHY 44 RHI1 45 RINV 46 R263 47 HIJ 48 RCMP 49 VFA1 50 VFA2 51 VFA3 52 VFA4 61 FMIN 62 FMON Data Range 0-1 0-1 0-1 0-1 0-1 0-1 0-1 0-15 0-7 0-15 0-15 0-15 0-15 0-15 0-15 0-15 0-3 0-1 0-2047 0-15 0-1 0-2047 0-1 0-7 0-1 0-2047 0-1 0-7 0-2047 0-1 0-1 0-1 0-1 0-4095 0-1 0-1 0-1 0-1 0-7 0-511 0-1 0-1 0-1 0-1 0-7 0-511 0-15 0-15 0-15 0-15 0-1 0-1 Initial Data 0 0 1 8 3 11 1 15 7 1039 16 16 375 5 1 Notes Function Display Item # Abbrev. Preset 63 PIP " 64 WXH1 " 65 WVST " 66 WMOD " 67 STLL " 68 WXLO " 69 WVED " 70 VFTH " 71 WKYF " 72 MULT " 73 AUTI " 74 WXCP " 75 W9HB " 76 W9IE " 77 WINT " 78 W9HS " 79 W9MV " 80 W9MH " 81 W9VS " 82 HYJM " 83 LRST " 84 CLST " 85 CLED " 86 HYPH " 87 HIQP " 88 MOSY " 89 MSIF " 90 MSQF " 91 MSIB " 92 MSQB " 93 HFRI " 94 HFRQ " 95 HFRY " 96 HWNI " 97 HWNQ " 98 HWNY " 99 R11S " 100 RF11 " 101 R12S " 102 RF12 " 103 R13S " 104 RF13 " 105 R14S " 106 RF14 " 107 R15S " 108 RF15 " 109 R16S " 110 RF16 " 111 R17S " 112 RF17 " 113 R18S " 114 RF18 (Continued on next page)
Page 39
Data Range 0-1 0-7 0-511 0-15 0-1 0-3 0-511 0-1 0-1 0-3 0-1 0-127 0-7 0-1023 0-15 0-511 0-3 0-7 0-255 0-1 0-1023 0-255 0-255 0-7 0-3 0-255 0-15 0-15 0-15 0-15 0-15 0-15 0-255 0-15 0-15 0-255 0-1 0-1023 0-1 0-1023 0-1 0-1023 0-1 0-1023 0-1 0-1023 0-1 0-1023 0-1 0-1023 0-1 0-1023
IC7001 (TC90A17F) Initial Notes Data 1 Preset " 25 " 4 " " 2 " 250 " " " " " " 0 " 0 " " 0 " " " 0 " " 32 " 143 " 147 " " " " " " " " " " " " 7 " 63 " " " " " " " " " " " " " " " " "
MODELS: VS-50805 / VS-60805 / WT-46805 / WS-55805 / WS-55905 / WS-65905 / WS-73905 SUB SCALAR Function (V16W, NTSC Only)
Function Display Item # Abbrev. 115 R19S 116 RF19 117 R1AS 118 RF1A 119 REHI 120 RHWE 121 REMD 122 RHWS 123 RELO 124 RVWE 125 RSHI 126 RVWS 127 RSMD 128 RHSZ 129 RSLO 130 RVSZ 131 RRH 132 RRV 133 RWRN 134 RWRA 135 RHFH 136 RHFV 137 RHIV 138 PRHP 139 PVPG 140 RREI 141 RRST 142 RCKI Data Range 0-1 0-1023 0-1 0-1023 0-15 0-4095 0-15 0-4095 0-15 0-1023 0-15 0-1023 0-15 0-4095 0-15 0-1023 0-4095 0-1023 0-1023 0-1023 0-1 0-1 0-1 0-4095 1023 0-1 0-1 0-1 Initial Data 2 250 15 11 1 15 2 1 15 253 0 75 275 245 55 55 990 87 Notes Preset " " " " " " " " " " " " " " " " " " " " " " " " " " " Function Display Item # Abbrev. 143 RREP 144 RMUT 145 YSVO 146 PAPS 147 FRF1 148 ROEA 149 RFIS 150 RFIA 151 RFIH 152 RFIH 153 OSYA 154 OSYB 155 OSXA 156 OSXB 157 OSXC 158 OSXD 159 OSXE 160 ODDX 161 OSDX 162 ODDY 163 OSDY 164 OKDS 165 OSDS 166 OLSL 167 ON1B 168 OWRS 169 OCRW 170 OKRW Data Range 0-3 0-1 0-1 0-1 0-1 0-1 0-1 0-1 0-15 0-15 0-3 0-3 0-3 0-3 0-3 0-3 0-3 0-255 0-255 0-255 0-255 0-1 0-1 0-1 0-1 0-1 0-1 0-1 Initial Data 0 1 134 (Continued) Notes Preset " " " " " " " " " " " " " " " " " " " " " " " " " " "
HR Function
Item 1
ABBREV Description NTSC HD HR OSD Horizontal Positioning 128 128
Note: The data tables for the I/O Expander and Sub Micro Functions are not given. These are for factory use only. If data is changed, it will automatically default to the factory setting when the Circuit Adjustment mode is terminated.
DF (Dynamic Focus)
Item Number 0 1 Abbrev. Name DFH DFV
Description
Dynamic Focus Horizontal Dynamic Focus Vertical
(MENU-1-2-5-9-5) Data (SD & HD) Notes V16N V16W 175 200 Preset 50 40 "
Page 40
MODELS: VS-50805 / VS-60805 / WT-46805 / WS-55805 / WS-55905 / WS-65905 / WS-73905 CONV MISC Items
Item Abbrev. Description Number Name 0 HVOL High Voltage Control 1 VSTR Vertical Correction Signal Start Point 2 VCNT Vert. Correction Increment per line 3 STLN Horiz. Correction Start Line Number 4 FPHS Fine H-Phase of Correction Signal 5 CPHS Coarse H-Phase of Correction Signal 6 DPHS Dynamic Focus H-Phase 7 TPHS Test Pattern H-Phase 8 HDLY HBLK Delay 9 PLWD HBLK Pulse Width * Do not change "0 HVOL" if it has been previously set. (MENU-1-2-5-9-6) SD Data HD Data Notes V16N V16W V16N V16W 197* 197* 197* 197* HV Adj. 0 0 0 0 Preset 29 29 29 29 " 49 39 81 81 " 186 178 186 178 " 23 23 29 29 " 250 245 250 245 " 83 90 83 92 " 235 235 240 240 " 0 0 31 31 "
CONV GREEN Items
Item Number 0 1 2 3 4 5 6 7
Abbrev. Description Name HSTA* Horizontal Position SPCC Side Pincushion Correction HWID Width SKEW Skew (Y axis rotation) VSTA* Vertical Position VKEY Vertical Keystone Correction TBPC Top/Bottom Pincushion Correction TILT Horizontal Tilt (X axis rotation) *HSTA and VSTA must not exceed ±200
50-60" -35/-35 0/0 0/0 0/0 -35/-35 0/-10 -220/-150 0/0
Data (SD/HD) 55-65-73" 46" 0/0 0/0 -220/-200 -220/-200
(MENU-1-2-5-9-5) Notes Centering Geo. (Conv) Geo. (Conv) Geo. (Conv) Centering Geo. (Conv) Geo. (Conv) Geo. (Conv)
CONV RED Items
Item Number 0 1 2 3 4 5 6 7
Abbrev. Description Name HSTA* Horizontal Position HLIN Horiz. Linearity SKEW Skew (Y axis rotation) HWID Width HSBW Horiz. Side Bow Correction VST* Vertical Position VKEY Vertical Keystone Correction TILT Horizontal Tilt (X axis rotation) *HSTA and VSTA must not exceed ±200
50-60" +50/+50 -220/-200 0/0 0/0 30/30 -20/-20 -140/-120 0/0
Data (SD/HD) 55-65-73" 46" +40/+50 +75/+75 -210/-200 -225/-210 +10/+10 +5/+5 -25/-5 +15/+20 -100/-100 -115/-85
(MENU-1-2-5-9-5) Notes Static Conv. Coarse Conv. Coarse Conv. Coarse Conv. Coarse Conv. Static Conv. Coarse Conv. Coarse Conv.
CONV BLUE Items
Item Number 0 1 2 3 4 5 6 7
Abbrev. Description Name HSTA* Horizontal Position HLIN Horiz. Linearity SKEW Skew (Y axis rotation) HWID Width HSBW Horiz. Side Bow Correction VST* Vertical Position VKEY Vertical Keystone Correction TILT Horizontal Tilt (X axis rotation) *HSTA and VSTA must not exceed ±200
Data (SD/HD) 50-60" 55-65-73" 46" -50/-50 -40/-40 -75/-75 +220/+200 +240/+220 +240/+215 0/0 -10/-10 0/0 0/0 -20/-5 -15/-20 -50/-50 -45/-45 -45/-45 -20/-20 -10/-10 -5/-5 +140/+120 +115/+115 +115/+105 0/0 0/0
(MENU-1-2-5-9-5) Notes Static Conv. Coarse Conv. Coarse Conv. Coarse Conv. Coarse Conv. Static Conv. Coarse Conv. Coarse Conv.
Page 41