Text preview for : Lens-Screen-DiamondShield-WS-55905-65905-73905-WT-46805.pdf part of Mitsubishi VS-50805, WT-60805, WS-55905, WS-65905, WS-73905, WS-55805, WT-46805 Mitsubishi VS-50805, WT-60805, WS-55905, WS-65905, WS-73905, WS-55805, WT-46805 (Chassis V16 N W) (Training Manual + Schematic)
Back to : Mitsubishi VS-50805, 6080 | Home
MODELS: VS-50805 / VS-60805 / WT-46805 / WS-55805 / WS-55905 / WS-65905 / WS-73905
SERVICING THE LENTICULAR SCREEN AND FRESNEL LENS
CAUTION: Wear gloves when handling the Lenticular Screen and Fresnel Lens. This prevents cuts and finger prints. Do not place Fresnel Lens in the sun. This may cause fine and heat related injuries.
WS-55905 / WS-65905 / WS-73905 / WT-46805 1a. Lenticular Screen and Fresnel Lens Removal
1. Remove the screen assembly shown in the Cabinet Disassembly procedure. 2. Remove the Screen Frame top section by removing 4 screws (a). 3. Carefully grasp the Lenticular Screen and Fresnel Lens combination and pull upward and out of the Screen Frame Assembly. Note: When separating the Lenticular Screen from the Fresnel Lens, use caution while prying the Screen and Lens apart. Use a slot type screw drive, and remove the pressure sensitive double sided tape.
Page 11
MODELS: VS-50805 / VS-60805 / WT-46805 / WS-55805 / WS-55905 / WS-65905 / WS-73905
SERVICING THE LENTICULAR SCREEN AND FRESNEL LENS
2. Lenticular Screen and Fresnel Lens Installation.
Note: Store the Lenticular Screen and Fresnel Lens in a cool dry place. High humidity may deform the Lenticular Screen and Fresnel Lens. 1. Apply double coated tape (Part # LENS-TAPE) along the top front edge of the Fresnel Lens as shown below. Refer to the Table below for proper tape length. 2. Place the Fresnel Lens on top of the Lenticular Screen and apply pressure at the top edge to bond them together as shown below.
MODEL VS-50805 VS-60805 WS-55805 WS-55905 WS-65905 WS-73905 WT-46805
SCREEN TAPE SIZE LENGTH 50" 60" 55" 55" 65" 73" 46" 37.5" 45" 45" 45" 53" 60" 37.5"
Page 12
MODELS: VS-50805 / VS-60805 / WT-46805 / WS-55805 / WS-55905 / WS-65905 / WS-73905
SERVICING THE DIAMONDSHIELDTM 1. DiamondShieldTM Removal Procedure
Note: Wear gloves when handling the DiamondShieldTM to prevent finger prints.
1. Remove the left and right molding clips by gently inserting a small screwdriver between the DiamondShieldTM and one end of the clip.
2. Gently pry both clips loose and remove them by pulling toward you.
3. Carefully insert a small screwdriver into the gap between the DiamondShieldTM and the Lenticular Screen at the side/center point. Pivot the screwdriver up and forward to pull the side edge of the DiamondShieldTM slightly away from the unit. Then, with your left and right hands placed at the approximate points shown, gently bow the DiamondShieldTM toward you and away from the unit to remove.
4. Complete the DiamondShieldTM removal by replacing the molding clips removed in step 2. For both the left and right, press the clip into place starting at one corner. Then, run a finger along the length of the clip to press it into place. Do not force.
Page 15
MODELS: VS-50805 / VS-60805 / WT-46805 / WS-55805 / WS-55905 / WS-65905 / WS-73905 2. DiamondShieldTM Installation Procedure *(See Parts List for DiamondShieldTM part numbers)
1. Remove the left and right molding clips by gently inserting a small screwdriver between the DiamondShieldTM and one end of the clip.
2. Gently pry both clips loose and remove them by pulling toward you.
3. Install the DiamondShieldTM by first inserting the bottom edge into the bottom channel. Then, with your left and right hands placed at the approximate points shown, gently bow the shield toward you and insert the top end of the DiamondShieldTM into the top channel.
4. Complete the DiamondShieldTM installation by replacing the molding clips removed in step 2. For both the left and right, press the clip into place starting at one corner. Then, run a finger along the length of the clip to press it into place. Do not force.
Page 16