Text preview for : Samsung SP403JHAX (Chassis PLT51A) (Service Manual).pdf part of Samsung SP403JHAX Samsung SP403JHAX (Chassis PLT51A) (Service Manual)
Back to : Samsung SP403JHAX (Chassi | Home
LCD PROJECTION TELEVISION
Chassis : Model: PLT51A SP403JHAX
LCD PROJECTION TELEVISION
CONTENTS
1. Precautions 2. Reference Information 3. Specifications 4. Disassembly and Reassembly 5. Alignment and Adjustments 6. Troubleshooting 7. Exploded View and Parts List 8. Electric Parts List 9. Block Diagram 10. PCB Layout Diagram 11. Wiring Diagram 12. Schematic Diagrams
Precautions
1. Precautions
Follow these safety, servicing and ESD precautions to prevent damage and protect against potential hazards such as electrical shock and X-rays.
1-1 Safety Precautions
1. Be sure that all of the built-in protective devices are replaced. Restore any missing protective shields. 2. When reinstalling the chassis and its assemblies, be sure to restore all protective devices, including: nonmetallic control knobs and compartment covers. 3. Make sure that there are no cabinet openings through which peopleÑparticularly childrenÑmight insert fingers and contact dangerous voltages. Such openings include the spacing between the picture tube and the cabinet mask, excessively wide cabinet ventilation slots, and improperly fitted back covers. If the measured resistance is less than 1.0 megohm or greater than 5.2 megohms, an abnormality exists that must be corrected before the unit is returned to the customer. 4. Leakage Current Hot Check (Figure 1-1): Warning: Do not use an isolation transformer during this test. Use a leakagecurrent tester or a metering system that complies with American National Standards Institute (ANIS C101.1, Leakage Current for Appliances), and Underwriters Laboratories (UL Publication UL1410, 59.7). 5. With the unit completely reassembled, plug the AC line cord directly into the power outlet. With the unitÕs AC switch first in the ON position and then OFF, measure the current between a known earth ground (metal water pipe, conduit, etc.) and all exposed metal parts, including: antennas, handle brackets, metal cabinets, screwheads and control shafts. The current measured should not exceed 0.5 milliamp. Reverse the powerplug prongs in the AC outlet and repeat the test.
DEVICE UNDER TEST TEST ALL EXPOSED METAL SURFACES 2-WIRE CORD ALSO TEST WITH PLUG REVERSED (USING AC ADAPTER PLUG AS REQUIRED)
LEAKAGE CURRENT TESTER
(READING SHOULD NOT BE ABOVE 0.5mA)
EARTH GROUND
Fig. 1-1 AC Leakage Test 6. Antenna Cold Check: With the unitÕs AC plug disconnected from the AC source, connect an electrical jumper across the two AC prongs. Connect one lead of the ohmmeter to an AC prong. Connect the other lead to the coaxial connector. 7. X-ray Limits: The picture tube is especially designed to prohibit X-ray emissions. To ensure continued X-ray protection, replace the picture tube only with one that is the same type as the original. Carefully reinstall the picture tube shields and mounting hardware; these also provide X-ray protection. 8. High Voltage Limits: High voltage must be measured each time servicing is done on the B+, horizontal deflection or high voltage circuits. Correct operation of the X-ray protection circuits must be reconfirmed whenever they are serviced. (X-ray protection circuits also may be called Òhorizontal disableÓ or Òhold-downÓ.) Heed the high voltage limits. These include the XÐray Protection Specifications Label, and the Product Safety and X-ray Warning Note on the service data schematic.
Samsung Electronics
1-1
Precautions
1-1 Safety Precautions (Continued)
9. High voltage is maintained within specified limits by close-tolerance, safety-related components and adjustments. If the high voltage exceeds the specified limits, check each of the special components. 10. Design Alteration Warning: Never alter or add to the mechanical or electrical design of this unit. Example: Do not add auxiliary audio or video connectors. Such alterations might create a safety hazard. Also, any design changes or additions will void the manufacturerÕs warranty. 11. Hot Chassis Warning: Some TV receiver chassis are electrically connected directly to one conductor of the AC power cord. If an isolation transformer is not used, these units may be safely serviced only if the AC power plug is inserted so that the chassis is connected to the ground side of the AC source. To confirm that the AC power plug is inserted correctly, do the following: Using an AC voltmeter, measure the voltage between the chassis and a known earth ground. If the reading is greater than 1.0V, remove the AC power plug, reverse its polarity and reinsert. Re-measure the voltage between the chassis and ground. 12. Some TV chassis are designed to operate with 85 volts AC between chassis and ground, regardless of the AC plug polarity. These units can be safely serviced only if an isolation transformer inserted between the receiver and the power source. 13. Some TV chassis have a secondary ground system in addition to the main chassis ground. This secondary ground system is not isolated from the AC power line. The two ground systems are electrically separated by insulating material that must not be defeated or altered. 14. Components, parts and wiring that appear to have overheated or that are otherwise damaged should be replaced with parts that meet the original specifications. Always determine the cause of damage or overheating, and correct any potential hazards. 15. Observe the original lead dress, especially near the following areas: Antenna wiring, sharp edges, and especially the AC and high voltage power supplies. Always inspect for pinched, out-of-place, or frayed wiring. Do not change the spacing between components and the printed circuit board. Check the AC power cord for damage. Make sure that leads and components do not touch thermally hot parts. 16. Picture Tube Implosion Warning: The picture tube in this receiver employs Òintegral implosionÓ protection. To ensure continued implosion protection, make sure that the replacement picture tube is the same as the original. 17. Do not remove, install or handle the picture tube without first putting on shatterproof goggles equipped with side shields. Never handle the picture tube by its neck. Some Òin-lineÓ picture tubes are equipped with a permanently attached deflection yoke; do not try to remove such Òpermanently attachedÓ yokes from the picture tube. 18. Product Safety Notice: Some electrical and mechanical parts have special safety-related characteristics which might not be obvious from visual inspection. These safety features and the protection they give might be lost if the replacement component differs from the originalÑeven if the replacement is rated for higher voltage, wattage, etc. Components that are critical for safety are indicated in the circuit diagram by shading, ( ) or ( ! ). Use replacement components that have the same ratings, especially for flame resistance and dielectric strength specifications. A replacement part that does not have the same safety characteristics as the original might create shock, fire or other hazards.
1-2
Samsung Electronics
Precautions
1-2 Servicing Precautions
Warning1: First read the "Safety Precautions" section of this manual. If some unforeseen circumstance creates a conflict between the servicing and safety precautions, always follow the safety precautions. Warning2: An electrolytic capacitor installed with the wrong polarity might explode. 1. Servicing precautions are printed on the cabinet. Follow them. 2. Always unplug the unitÕs AC power cord from the AC power source before attempting to: (a) Remove or reinstall any component or assembly, (b) Disconnect an electrical plug or connector, (c) Connect a test component in parallel with an electrolytic capacitor. 3. Some components are raised above the printed circuit board for safety. An insulation tube or tape is sometimes used. The internal wiring is sometimes clamped to prevent contact with thermally hot components. Reinstall all such elements to their original position. 4. After servicing, always check that the screws, components and wiring have been correctly reinstalled. Make sure that the portion around the serviced part has not been damaged. 5. Check the insulation between the blades of the AC plug and accessible conductive parts (examples: metal panels, input terminals and earphone jacks). 6. Insulation Checking Procedure: Disconnect the power cord from the AC source and turn the power switch ON. Connect an insulation resistance meter (500V) to the blades of the AC plug. The insulation resistance between each blade of the AC plug and accessible conductive parts (see above) should be greater than 1 megohm. 7. Never defeat any of the B+ voltage interlocks. Do not apply AC power to the unit (or any of its assemblies) unless all solid-state heat sinks are correctly installed. 8. Always connect a test instrumentÕs ground lead to the instrument chassis ground before connecting the positive lead; always remove the instrumentÕs ground lead last. 9. When some parts inside the optical engine (except lamp) are damaged, replace the whole optical engine.
Samsung Electronics
1-3
Precautions
1-3 Precautions for Electrostatically Sensitive Devices (ESDs)
1. Some semiconductor (Òsolid stateÓ) devices are easily damaged by static electricity. Such components are called Electrostatically Sensitive Devices (ESDs); examples include integrated circuits and some field-effect transistors. The following techniques will reduce the occurrence of component damage caused by static electricity. 2. Immediately before handling any semicon ductor components or assemblies, drain the electrostatic charge from your body by touching a known earth ground. Alternatively, wear a discharging wrist-strap device. (Be sure to remove it prior to applying powerÑ this is an electric shock precaution.) 3. After removing an ESD-equipped assembly, place it on a conductive surface such as aluminum foil to prevent accumulation of electrostatic charge. 4. Do not use freon-propelled chemicals. These can generate electrical charges that damage ESDs. 5. Use only a grounded-tip soldering iron when soldering or unsoldering ESDs. 6. Use only an anti-static solder removal device. Many solder removal devices are not rated as Òanti-staticÓ; these can accumulate sufficient electrical charge to damage ESDs. 7. Do not remove a replacement ESD from its protective package until you are ready to install it. Most replacement ESDs are packaged with leads that are electrically shorted together by conductive foam, aluminum foil or other conductive materials. 8. Immediately before removing the protective material from the leads of a replacement ESD, touch the protective material to the chassis or circuit assembly into which the device will be installed. 9. Minimize body motions when handling unpackaged replacement ESDs. Motions such as brushing clothes together, or lifting a foot from a carpeted floor can generate enough static electricity to damage an ESD.
1-4
Samsung Electronics
Reference Information
2. Reference Information
2-1 Tables of Abbreviations and Acronyms
Table 2-1 Abbreviations A Ah Å dB dBm °C °F °K F G GHz g H Hz h ips kWh kg kHz k km km/h kV kVA kW I MHz Ampere Ampere-hour Angstrom Decibel Decibel Referenced to One Milliwatt Degree Celsius Degree Fahrenheit degree Kelvin Farad Gauss Gigahertz Gram Henry Hertz Hour Inches Per Second Kilowatt-hour Kilogram Kilohertz Kilohm Kilometer Kilometer Per Hour Kilovolt Kilovolt-ampere Kilowatt Liter Megahertz MV MW M m µA µF µH µm µs µW mA mg mH mI mm ms mV nF pF Ib rpm rps s V VA W Wh Megavolt Megawatt Megohm Meter Microampere Microfarad Microhenry Micrometer Microsecond Microwatt Milliampere Milligram Millihenry Milliliter Millimeter Millisecond Millivolt Nanofarad Ohm Picofarad Pound Revolutions Per Minute Revolutions Per Second Second (Time) Volt Volt-ampere Watt Watt-hour
Samsung Electronics
2-1
Reference Information
Table 2-1 Abbreviations ABL AC ACC AF AFC AFT AGC AM ANSI APC APC A/V AVC BAL BPF B-Y CATV CB CCD CCTV Ch CRT CW DC DVM EIA ESD ESD FBP FBT FF FM FS GND G-Y H HF HI-FI IC IC IF Automatic Brightness Limiter Alternating Current Automatic Chroma Control Audio Frequency Automatic Frequency Control Automatic Fine Tuning Automatic Gain Control Amplitude Modulation American National Standards Institute Automatic Phase Control Automatic Picture Control Audio-Video Automatic Volume Control Balance Bandpass Filter Blue-Y Community Antenna Television (Cable TV) Citizens Band Charge Coupled Device Closed Circuit Television Channel Cathode Ray Tube Continuous Wave Direct Current Digital Volt Meter Electronics Industries Association Electrostatic Discharge Electrostatically Sensitive Device Feedback Pulse Flyback Transformer Flip-Flop Frequency Modulation Fail Safe Ground Green-Y High High-Frequency High Fidelity Inductance-Capacitance Integrated Circuit Intermediate Frequency I/O L L LED LF MOSFET MTS NAB NEC NTSC OSD PCB PLL PWM QIF R RC RF R-Y SAP SAW SIF SMPS S/N SW TP TTL TV UHF UL UV VCD VCO VCXO VHF VIF VR VTR VTVM TR Input/output Left Low Light Emitting Diode Low Frequency Metal-Oxide-Semiconductor-Field-Effect-Tr Multi-channel Television Sound National Association of Broadcasters National Electric Code National Television Systems Committee On Screen Display Printed Circuit Board Phase-Locked Loop Pulse Width Modulation Quadrature Intermediate Frequency Right Resistor & Capacitor Radio Frequency Red-Y Second Audio Program Surface Acoustic Wave(Filter) Sound Intermediate Frequency Switching Mode Power Supply Signal/Noise Switch Test Point Transistor Transistor Logic Television Ultra High Frequency Underwriters Laboratories Ultraviolet Variable-Capacitance Diode Voltage Controlled Oscillator Voltage Controlled Crystal Oscillator Very High Frequency Video Intermediate Frequency Variable Resistor Video Tape Recorder Vacuum Tube Voltmeter Transistor
2-2
Samsung Electronics
Reference Information
2-2 IC Line Up
Table 2 - 2 IC Line - Up BLOCK SPECIFICATION TDA9810T TDA7265 MAIN PCF8574P SAA1300 TDA6920X AV-TERMINAL TEA5114A TL062CDT MSP3410D DPL3519A SOUND TL062CDT 74HC4052 SDA30C264 ST24W16 TMS27C040 MICOM SDA5273P KM44C1004D HD74HC123P 74HC04D TDA4780 LCD-CONTROL TDA8444 CXA1853Q CXA2504N CXD2443Q CIP3215A VPC3210A TL7705AC SDA9280 FEATURE-BOX SDA9272 SDA9253 74F125 74F541 MAKER PHILLIPS SGS-THOMSON PHILIPS PHILIPS SIEMENS SGS-THOMSON T.I ITT ITT T.I PHILIPS SIEMENS SGS-THOMSON T.I SIEMENS SEC HITACHI PHILIPS PHILIPS PHILIPS SONY SONY SONY ITT ITT T.I SIEMENS SIEMENS SIEMENS PHILIPS PHILIPS FUNCTION VIF (QSS-IF&AM) STEREO AMP (25W) FAN,LEVER S/W,THERMO S/W DETECT LED CONTROL, LAMP ON/OFF 7*5 VIDEO S/W VIDEO S/W OP AMP SOUND PROCESSOR DOLBY PRO LOGIC OP AMP ANALOG-MULTIPLEXER 8-BIT MICRO CONTROLLER EEPROM (2K*8) PROGRAMMABLE ROM MEGATEXT DRAM (1M*4BIT) MULTIVIBRATOR CMOS-LOGIC RGB CONTROL DAC RGB DRIVER SAMPLE/HOLD DRIVER TIMING GENERATOR COMPONENT INTERFACE PROCESSOR VIDEO PROCESSOR POWER-ON RESET GENERATOR DISPLAY PROCESSOR VIDEO INTERPOLATION PROCESSOR DRAM BUFFER BUFFER
Samsung Electronics
2-3
Specifications
3. Specifications
MODEL Progressive MAIN Dolby Prologic CHARACTERISTICS AV- LINK TUNING SYSTEM COLOR SOUND ANTENNA INPUT CONSUMPTION POWER REQUIREMENTS FREQUENCY SIZE LCD TYPE NUMBER OF CHANNELS TUNING RANGE SOUND OUTPUT
SP-403JHA 0 0 (3D Sound) 0 Frequency Synthesizer PAL, SECAM, NTSC (only AV mode) NICAM, A2 STEREO, AM 75W, Coaxial Cable 168 W Main Voltage : 230V Input Range : 220 ~240V 50Hz 1.43" , 16:9 p-Si : Active matrix TFT 100 VHF : 2 ~ 12, UHF : 21 ~ 69, Cable : S1 ~ S41 Right : 13W Left : 13W -1 RCA Input / 1 S-Video input -Headphone Audio Output -EXT1 : full RGB Scart / AV-LINK -EXT2 : Scart (Output Selectable) -EXT3 : Decoder (Output Selectable) -Dolby Prologic Signal Output (RCA Jack)
EXT4
SOCKETS BACK (3 SCARTS)
Specifications are subject to change.
Samsung Electronics
3-1
Disassembly and Reassembly
4. Disassembly and Reassembly
4-1 Back Cover Removal
1. After removing the 16 screws, pull the bottom part of the cabinet back wards.
2. Loosen the 4 screws and remove the supporter.
3. After loosening the 4 screws, remove the lens cover and fan duct.
4. Loosen the 2 screws. Remove the optical meter.
5. Loosen the 2 screws. Remove the stabilizer.
Samsung Electronics
4-1
Disassembly and Reassembly
6. After loosening the 2 screws, remove the chassis holder and power mounting.
7. After removing the 6 screws, pull the top cabinet backwards.
4-2
Samsung Electronics
Disassembly and Reassembly
4-2 Lamp Replacement
1. Loosen the screw. 2. Remove the cover.
3. Using a hexagonal wrench, loosen the two screws that secure the lamp.
4. Pull out the lamp.
5. PROCEDURE After completing the lamp replacement, enter the Service Mode Press the remote control Keys in the following sequence: ÒDisplay P.STD Mute PowerÓ
(1) Select 01 (lamp life) with using the channel (w) key, then press the volume (+) key (See the figure below). (2) Press the Cancel key to reset the lamp life (Ò00000Ó). (3) Press the Power key to reset the factory value. (4) Press the DISPLAY key to verify that the lamp use time is ø.
00 Lamp Total time (05999) 01 Lamp Life (05999)
Samsung Electronics
4-3
Disassembly and Reassembly
4-2-1 Lamp (Bulb only) Replacement
1. Loosen the two screws.
2. Remove the lamp-bracket from the lamp assembly.
3. After loosening the two brackets, remove the lamp-holder and wires.
4. After loosening one screw and one nut, remove the bulb.
4-4
Samsung Electronics
Disassembly and Reassembly
4-3 Air Filter Check
1. Loosen the screw.
2. Remove the cover.
3. After removing the holder and filter from the cover, clean the filter.
FILTER
Samsung Electronics
4-5
Disassembly and Reassembly
4-4 Liquid Crystal Panel Replacement
1. After removing the 16 screws, pull the cabinet backwards. 2. Loosen the 3 screws. Remove the supporter.
3. After loosening the 4 screws, remove the lens cover and fan duct.
4. Loosen the 2 screws. Remove the optical meter.
5. Remove the GUIDE from the FPC-Connector.
6. Remove FPC cable from the FPC-Connector.
4-6
Samsung Electronics
Disassembly and Reassembly
7. Loosen the 2 screws, 2 PCB spacers and remove the PCB-LCD.
8. Using a hexagonal wrench, loosen the two screws.
9. Lift the LCD in the direction of arrow.
Samsung Electronics
4-7
Disassembly and Reassembly
4-5 Speaker Removal
1. Loosen the 4 screws and remove the speaker holders.
4-8
Samsung Electronics
Alignment and Adjustments
5. Alignment and Adjustments
5-1 Lens and Mirror Cleaning
1. Mix the alcohol and ethyl in appropriate proportions. 2. Use a clean cotton cloth or a cleaning paper. 3. Clean the top of the lens by turning it as shown. The pattern starts at the center and proceeds outward, as shown below:
4. Use minimal pressure when rubbing the mirror. Otherwise, the surface will be damaged.
5-2 Focus Adjustment for projection Lens
1. Loosen the 4 screws that secure the optical assembly. 2. After setting the optical assembly on the front cabinet, secure the unit temporarily using the two screws. 3. After applying the liquid crystal panel signal, input a lion head pattern from a pattern generator. 4. Move the focus adjustment screws right and left until the liquid crystal picture element is clearly displayed on the screen. 5. Reposition the optical assembly, and fasten all 4 screws. 6. Check the focus adjustment. 7. Repeat adjustments 1~5, if necessary. FOCUS SECURING SCREW FOCUS SECURING SCREW
FOCUS ADJUSTMENT SCREW
Fig. 5-1
Samsung Electronics
5-1
Alignment and Adjustments
5-3 Liquid Crystal Screen Center Adjustment
After replacing with the new liquid crystal panel, make sure that the liquid crystal screen center is aligned with the screen center. If they are not aligned, make the following adjustments: 1. Using a hexagonal wrench, loosen the two screws that secure the liquid crystal panel. Note: Loosen the screws just until the panel can move easily. 2. Using two fingers, lift the liquid crystal upward. (The screen moves downward.) 3. When moving the liquid crystal panel towards the left, the screen moves right (and vice versa). 5. Repeat adjustments 2~4 until the screen center is aligned vertically and horizontally. 6. Using a hexagonal wrench, refasten the two screws.
HEXAGONAL SCREW (FOR SECURING LIQUID CRYSTAL PANEL)
Fig. 5-2
5-2
Samsung Electronics
Alignment and Adjustments
5-4 Side Panel Controls
SIDE PANEL CONTROLS (THE OPERATION PANEL OPENS OUTWARD WHEN PRESSED)
CHANNEL
MENU
VOLUME
HEADPHONE
R A U D I O L V I D E O
E X T 4
CHANNEL
MENU
VOLUME
HEADPHONE
R A U D I O L V I D E O
E X T 4
SVIDEO
SAV
Picture/Lamp/Standby/Temp / /
1
LED Indicator
4-4-1 Rear Panel Jacks
5-4-2 Side Operation Panel
EXT3 (DECODER) AUDIO OUT EXT2 (VCR) 75W EXT1
AV-link
SURROUND REAR L L
FRONT
CENTER
CHANNEL
Channel Select Button 1. Press for the channel selection. 2. Press for the content adjustment.
R
R
MENU
VOLUME
HEADPHONE
R A U D I O L V I D E O
SVIDEO
Volume Button 1. Press for the volume UP/DOWN. 2. Press for content adjustment.
Sound Input Terminal (Right)
E X T 4
Sound Input Terminal (left)
Video Input Terminal
Seperate-Video Input Terminal
Samsung Electronics
5-3
Alignment and Adjustments
5-5 Service Mode Adjustments
5-5-1 MATRIX IC (TDA4780) Adjustment
No. 00 01 02 03 04 05 06 07 08 09 10 11 12 Item RED DRIVE GREEN DRIVE BLUE DRIVE RED CUTOFF GREEN CUTOFF BLUE CUTOFF SUB BRIGHTNESS SUB CONTRAST SUB COLOR PEAK DRIVE LIMIT P.YC DELAY SUB TINT g CORRECTION Range 63 63 63 63 63 63 20 20 20 63 15 17 63 Initial value 52 48 53 32 32 32 14 20 00 43 13 09 63 Adjustment for the R gain Adjustment for the G gain Adjustment for the B gain Adjustment for the R cutoff Adjustment for the G cutoff Adjustment for the B cutoff Adjustment for the brightness Adjustment for the contrast Adjusts the color difference signal level of YUVIN 1 Adjustment for the peak drive limit Adjustment for the P.YC delay Adjusts the center of tint (0 ®R 9 ®CENTER 17 ®G ) Adjustment for the g correction Description
5-4
Samsung Electronics
Alignment and Adjustments
5-5-2 LCD Interface IC (CXA1853_A) Adjustment
No. 00 01 02 03 04 05 06 Item Gamma gain 1 R gamma gain 1 B gamma gain 1 Gamma gain 2 R gamma gain 2 B gamma gain 2 Gamma ctrl 2 Range 63 63 63 63 63 63 63 Initial value 41 39 48 16 36 36 34 Description Adjusts the gain of black side on the gamma curve (R,G.B) Adjusts the gain of black side on the gamma curve for R Adjusts the gain of black side on the gamma curve for B Adjusts the gain of white side on the gamma curve (R,G.B) Adjusts the gain of white side on the gamma curve for R Adjusts the gain of white side on the gamma curve for R Adjusts the change point of the white side on the gamma curve (R,G,B). The smaller the value, the more it moves towards white. Adjust the DC level of R,G,B signal before doing the gamma adjustment. It determines the change point of the gamma curve. The greater the value, the darker it gets. Adjusts the DC level of R before doing the gamma adjustment. It determines the change point of the gamma curve. The greater the value, the darker it gets. Adjusts the DC level of B before doing the gamma adjustment. It determines the change point of the gamma curve. The greater the value, the darker it gets. Adjusts the limiter voltage of white peak of R,G,B video signal (applied to LCD). The greater the value, the lower the limiter voltage becomes.
07
Main bright
63
42
08
R main bright
63
36
09
B main bright
63
36
10
White limit
63
41
Samsung Electronics
5-5
Alignment and Adjustments
5-5-3 LCD Interface IC (CXA1853_B) Adjustment
No. 00 Item Gamma ctrl 1 off Range 63 Initial value 36 Description Adjusts the change point of the black side on the gamma curve (R,G,B). The greater the value, the more it moves towards black Adjusts the change point of the back side on the (R,G,B) gamma curve. Moves the change point to the white side. The value is always less than the one of the gamma ctrl 1 off. Adjusts the change point of the back side on the gamma curve for R. The greater the value, the more it moves towards black. Adjusts the change point of the black side on the gamma curve for B. The greater the value, the more it moves towards black. Adjusts the brightness of R, G, B after doing the gamma adjustment. No change of the gamma curve. The greater the value, the darker it gets. Adjusts the brightness of R after doing the gamma adjustment. No change on the gamma curve. The greater the value, the darker it gets. Adjusts the brightness of B after doing the gamma adjustment. No change on the gamma curve. The greater the value, the darker it gets. Adjusts the common voltage (applied to LCD) Adjusts the DC level of composite video signals (applied to LCD). Set the signal center to 7V. Adjusts the gain of R, G, B (applied to LCD). Adjusts the gain of R (applied to LCD). Adjusts the gain of B (applied to LCD).
01
Black Stretch On
36
33
02
R gamma ctrl 1
63
40
03
B gamma ctrl 1
63
32
04
Sub bright
20
10
05
R sub bright
63
35
06
B sub bright
63
42
07 08
Common ctrl Signal center
63 63
30 15
09 10 11
Sub contrast R sub contrast B sub contrast
63 63 63
47 42 34
5-5-4 LCD CONTROLLER (CXD2443Q) Adjustment
No. 00 Item LCD h pos Range 255 Initial value 70 Description Determines the start location of horizontal indication by picture element. Determines the start location of vertical indication (within 1H) Determines the phase of the sample/hold pulse.
01 02
LCD v pos SH position
15 15
3 6
5-6
Samsung Electronics
Alignment and Adjustments
5-5-5 Lamp's Total Hours
No. 00 Item lamp total time Range 05999 Initial value Description Records total elapsed time (from the time where power is first applied). Reset not possible Records total elapsed time (from the point where power is first applied). Reset (using the cancel key). The lamp time is displayed by using the Display key. Reset must be done during the set shipment. Reset must be done after lamp replacement.
01
lamp time
05999
5-5-6 Option
No. 00 01 02 03 04 05 06 07 08 09 10 11 12 13 Epg Av_link Palplus 27Mhz external 16 : 9 wide Dolby prologic 3d sound S-audio mute Blue screen UHF only Vga Atm one run Size key Vip option Item Range on/off on/off on/off on/off on/off on/off on/off on/off on/off on/off on/off on/off on/off on/off Initial value off on off on on on off on on off off on off on Electronic program guide Av_link 27Mhz external 16 : 9 wide Dolby prologic 3d sound Scart audio mute Blue screen UHF only Vga input Atm one run ("OFF" for France) Size key Vip option Description
Samsung Electronics
5-7
Alignment and Adjustments
5-6 Circuit Adjustments
5-6-1 LCD Control Board PLL Adjustment
1. Input a color bar signal. 2. Connect CNL06,RPD to an oscilloscope, and check the waveforms. (1 V/div, 20 u sec/div) 1. Input a 10-step signal (Color OFF). 2. Connect CNL07 (G output) to an oscilloscope, and check the waveform. (0.5 V/div, 10 u sec/div) 3. Adjust the green drive so that the signal amplitude becomes 0.7Vp-p.
5-6-4 Matrix G Output Signal Amplitude Adjustment (Green Drive)
DC2.8V RPD
5-6-2 Matrix IC (TDA4780) Sub Tint Adjustment
1. Input a color bar signal. 2. Connect CNL07 (B output) to an oscilloscope, and check the waveform. (0.5 V/div, 20 u sec/div)
5-6- 5 Matrix B Output Signal Amplitude Adjustment (Blue Drive)
1. Input a 10-step signal (Color OFF). 2. Connect CNL07 (B output) to an oscilloscope, and check the waveform. (0.5 V/div, 10 u sec/div) 3. Adjust the blue drive so that the signal amplitude becomes 0.7Vp-p.
5-6-6 Main Brightness Adjustment
1. Input a 10-step signal (Color OFF).
5-6-3 Matrix R Output Signal Amplitude Adjustment (Red Drive)
1. Input a 10-step signal (Color OFF). 2. Connect CNL07 (R output) to an oscilloscope, and check the waveform. (0.5 V/div, 10 u sec/div) 3. Adjust the red drive so that the signal amplitude becomes 0.7Vp-p. 4. Adjust the Sub-brightness of TDA4780 so that the waveform (without sync) is seen as shown in the figure below.
2. Connect LCD CNL08(R1) input to an oscilloscope, and check the waveform. (2 V/div, 10 u sec/div) 3. Adjust the main brightness so that the Ref pulse is positioned on the center of signal. Note : The change point (on gamma curve) is determined by Ref.
REF Pulse
Sync
5-8
Samsung Electronics
Alignment and Adjustments
5-6-7 R Main Brightness & B Main Brightness Adjustments
1. Input a 5-step signal (Color OFF).
5-6-9 B Sub-brightness & B Contrast Adjustments
1. Input a 5-step signal (Color OFF). 2. Connect CH1 to LCD G1 input and CH2 to LCD B1 input. (1 V/div, 10 u sec/div) 3. Reverse the CH2 signal, and add CH1 and CH2 in ADD mode. 4. Adjust B sub-contrast and B sub-brightness waveforms, as shown below:
2. Connect CH1 to LCD G1 input and CH2 to LCD R,B input. (1 V/div, 10 u sec/div) 3. Reverse the CH2 signal, and add CH1 and CH2 in ADD mode. 4. Adjust R,B main brightness for the waveform shown below. Note: The R,B main brightness adjustment should be done with Gamma Adjustment OFF (gamma ctrl1 = 63, gamma ctrl2 = 17).
Contrast Adjustment
Brightness Adjustment Brightness Adjustment
5-6-10 Gamma Adjustment 5-6-8 R Sub-brightness & R Contrast Adjustments
1. Input a 5-step signal (Color OFF). 2. Connect CH1 to LCD G1 input and CH2 to LCD R1 input. (1 V/div, 10 u sec/div) 3. Reverse the CH2 signal, and add CH1 and CH2 in ADD mode. 4. Adjust R sub-contrast and R sub-brightness waveforms, as shown below: 1. Input a 5-step signal (Color OFF). 2. Connect LCD G1 input to an oscilloscope. (2 V/div, 10 u sec/div) 3. Adjust the gamma gain1, gain2 and the gamma ctrl1, crtl2 for the waveform shown below.
Contrast Adjustment
Brightness Adjustment
Samsung Electronics
5-9
Alignment and Adjustments
5-6-11 Sub-Contrast Adjustment
1. Input a 5-step signal (Color OFF). 2. Connect LCD G1 input to an oscilloscope. (2 V/div, 10 u sec/div) 3. Adjust the sub-contrast so that the signal level is 3V, as shown below:
5-6-14 White Balance Adjustment
1. Input a lion head pattern from a pattern generator. 2. Adjust the sub-brightness so that the white cannot be saturated. 3. Adjust R,B contrast for the high light of white balance. 4. Adjust R,B sub-brightness when the middle tone is not black and white,but colored. Repeat adjustments 3 ~ 4 for optimum. 5. Adjust gamma crtl1 for adjusting the brightness of the black side.
Center 7V
3V
6. Adjust R,B gamma crtl1 while checking the tone of the black side so that any color is not seen. 7. Repeat adjustments 2 ~ 6, if necessary.
5-6-12 Signal Center Adjustment 5-6-15 Center Convergence Adjustment
1. Input a 5-step signal (Color OFF). 2. Connect LCD G1 input to an oscilloscope, and check the waveform. (2 V/div, 10 u sec/div) 3. Set the signal center to 7V. 1. Input a lion head pattern from a pattern generator. 2. Adjust the LCD Horizontal/Vertical POS.
5-6-13 Common Voltage Adjustment
1. Connect LCD COMMON input to an oscilloscope, and check the waveform. (1 V/div, 10 u sec/div) 2. Set the common control to 6.8V.
5-10
Samsung Electronics
Alignment and Adjustments
5-7 LED Display Check
PICTURE
LAMP
STAND BY/TEMP
Green
Red
Red
: OFF No 1 2 Status Master Power ON (in the Stand-by Mode) Normal operation Picture
: ON Lamp
: Blinking Stand By Temp
3
Lamp is warming up. The normal picture comes on after 25 seconds. Air vent cover in the rear of the TV is not properly installed.
or
4
5
Inside temperature of the TV is over normal. Clean the air vent cover in the rear of the TV. Turn the TV back on after 1 hour. (see below "Temperature") The lamp needs to be replaced.
6
x Temperature Wen the inside temperature of the TV becomes too high, the TV set is automatically turned off. You will observe the following. 1. "TEMP" LED is blinking for about 5 ~ 6 seconds. 2. The picture is turned to blue screen and "TEMPERATURE" character blinks for about 5 ~ 6 seconds. 3. The power is turned off and "TEMP" LED is blinking for about 20 seconds. (This is not a TV set failure and normal operation)
Samsung Electronics
5-11
Troubleshooting
6. Troubleshooting
6-1 Service Mode
1. To enter the Service Mode, press the remote-control keys in the following sequence: Display ® Picture Standard ® Mute ® Power
2. Use the Channel UP/DOWN keys to move within the Service Mode.
3. Use the Vol (+) key and Vol ( - ) key to change data. (1) Press the Vol (+) key to increase data. (2) Press the Vol (-) key to decrease data.
4. Use the Power key to exit and store data in memory.
Samsung Electronics
6-1
Troubleshooting
6-2 No Power
Check Stand-by 5V on the Main Board
Yes
No Check SDA1/SCL1 on the Micom Module See "6-5 No Standy" Yes Check LED Operation See "5-7 LED Display Check"
No
Check/Replace Tuner MICOM Module AUDIO Module A/V Terminal Board (TDA6920) Progressive Module LCD Control Board (TDA4780)
6-2
Samsung Electronics
Troubleshooting
6-3 No Picture
Yes
Check IC101 (TDA9810) #10 (AGC), #12 (CVBS)
No
No
Check Progressive Module M-Y/CVBS,2Hsync,Vsync, 2Y,2R-Y,2B-Y,Href
Yes Check/Replace IC101, Tuner
Replace Progressive Module
No
Check ICL404 (TDA4780) #14 (Sand castle pulse)
Yes
No
Check IC401,402,403 #5 (74HC1230
Yes No Check ICL404(TDA4780)#6(B-Y) #7(R-Y),#8(Y),#27(SDA) #28(SCL) Yes
First check the circuitry connected to the IC and replace the IC
No
Check CL129, 130,131 and AC2 5P connector for #6,7,8 Check AC1 12P and SDA,SCL output of micom module for #27,28
Yes
Check the circuitry near ICL404 and replace micom module
No
Check ICL404(TDA4780) #20(B-OUT),#22(G-OUT) #24(R-OUT) Yes
Check the circuitry near ICL404, replace IC201 (TDA4780) No Check ICL204(CXA1853Q) #9(R-in),#10(G-in),#11(B-in) Yes
Check the circuitry near QL401,QL402,QL403 around of ICL404(TDA4780)
No
Check ICL205(CXA2504N) #23,#25,#27,#33,#35,#37
Yes
Replace ICL205(CXA2504N)
Check/ Replace CNL04 (24P)
Samsung Electronics
6-3
Troubleshooting
6-4 No Sound
Yes
Check IC601,# 5 (MUTE)
No
No
Check Audio Module MAIN-L, SUR, CENTER, S-RESET, QSS-IN
Yes Check/Replace Q602, Q603 Micom Module IC601
Check/Replace IC101 Micom Module Audio Module
No
Check IC604 #9, #14, #15
Yes
Check/Replace IC604 MICOM Module
Replace IC601
6-5 No Standby (+5V)
Check the voltage of IC808 pin 5 (over 6V) No
Yes
Check/Replace IC808 Regulator IC (SI-3050C)
Check the AC power supply of D826
Yes
Check the associated circuitry parts of T802, IC801
No
Check F801
Yes
Replace F801 (AC250V/6.3A)
No
Check L801,L802, C801, C802, V801, R801
6-4
Samsung Electronics
Troubleshooting
6-6 No FAN Voltage (+8V)
Check the voltage of IC805 pin 5 (12V) No
Yes
Check /Replace IC805 Regulator IC (SI-3050C)
Check the voltage of T801 pin12
Yes
Check L811, D821, C836
No
Check T801/Replace trans
6-7 Lamp Does Not Work
Standby/Temp LED, Picture LED, Lamp LED flicker at the same time? Or, check the lamp time (6000 hrs)
Yes
Check/Replace Lamp
No
Check the DC voltage of BALLAST (about 300V)
Yes
Check the voltage of AB1 (connector) pin1 on the Main Board (over 3.5V)
Yes
No Check F801 (on the Power Board), D803, and surrounding circuitry
No Check the voltage of IC904(SAA1300) pin 6 (over 3.5V)on the Main Board
Check AB1 on the Ballast Board
Samsung Electronics
6-5
Troubleshooting
6-8 Horizontal Sync Flows
Horizontal Sync Flows
Yes Check the output of 2H-Sync from the progressive module Yes Check the output of 2H-Sync HREF to LCD Control Board Yes
No
Replace the progressive module
No
Check Connector Assy AC1
Check the input of 2H-sync to ICL301(CXD2443Q) Pin 13 on the LCD Control Board Yes
No
Check ICL402 (74HC123) Pin13,FI302
Check the voltage of CNL06 RPD (2.8V)
No
Check voltage of TL301 so that the voltage of CNL06 RPD is 2.8V
Yes Check the connector to LCD panel (CNL04)
6-6
Samsung Electronics
Troubleshooting
6-9 Vertical Sync Flows
Vertical Sync Flows
Yes Check the output of V-Sync HREF from progressive module Yes Check the input of V-Sync to LCD Control Board Yes Check the input of V-Sync to ICL301 Pin 14 on LCD Control Board Yes
No
Replace the progressive module
No
Check Connector Assy AC1
No
Check ICL402 (74HC123) Pin 5
Check CNL04 (connector to LCD panel)
Samsung Electronics
6-7
Exploded View & Parts List
7. Exploded View & Parts List
7-1 SP403JHAX
No
1-17 1-18 1-19 1-20 1-21 2 2-1 2-2 2-3 2-4 2-5 3 3-1 3-2 3-3 3-4 3-5 3-6 3-7 3-8 3-9 3-10 3-11 3-12 4 4-1 4-2 4-3 4-4 4-5 4-6 4-7 4-8 4-9 4-10 4-11 4-12 4-13 4-14 4-15 4-16 4-17 4-18 4-19 5 5-1 5-2 5-3 5-4 5-5 5-6 5-7 5-8 5-9 5-10 5-11 5-12 5-13 5-14 5-15
Code No
AA95-90031M AA95-90031J AA61-20217A AA95-10010X AA60-10008A AA67-70049A AA61-20215B AA67-70051A AA61-20214B 6002-000522 AA61-20215A AA67-20024A AA61-10341A AA61-10371A AA61-10344A AA61-10337A AA61-10340A AA61-10338A AA63-60052G AA61-10342A AA61-10339A AA63-60052F AA61-10323A AA61-10343A AA64-30854B AA63-30130A 6002-000522 AA91-20069A AA63-30180A AA63-30181A AA61-11006A 4712-000121 AA63-30176A AA64-60411B AA64-31012B 6002-000522 AA61-10379A AA64-60442A AA61-20253A AA63-60112B AA60-10050K AA63-30183B AA95-90033C AA61-11005 AA91-20057A AA61-20252A AA07-10002A AA95-90033B AA61-10185A 3409-000178 AA63-60123A AA95-90033B AA63-30223A AA63-30178A AA91-20069A AA63-30179A AA63-60123B AA63-50351A
Description
ASSY-PCB,MICOM ASSY-AV,TERMINAL HOLDER-CHASS/POWER ASSY-PCB,POWER SCREW-TAPPING SUN-SCREEN HOLDER-SCREEN,S SCREEN-TINT HOLDER-SCREEN,T SCREW-TAPPING HOLDER-SCREEN,T MIRROR-FRONT BRACKET-MIRROR,SUP BRACKET-BACK,SUP(A) BRACKET-BACK,BOT BRACKET-BACK,TOP BRACKET-MIRROR,SUP BRACKET-MIRROR,BOT SPACER-MIRROR BRACKET-MIRROR,SIDE BRACKET-MIRROR,TOP SPACER-MIRRORPVC BRACKET-FRONT,T BRACKET-MIRROR,SIDE CABINET-B/TOP COVER-DUCT SCREW-TAPPING ASSY-DUCT,IN COVER-DUCT,OUT,R COVER-DUCT,OUT,L BRACKET-LAMP THERMOSTAT COVER-LENS,A INLAY-LAMP CABINET-BACK,BO SCREW-TAPPING BRACKET-COVER INLAY-TERMINAL,PAL HOLDER-SPONGE,A SPACER-SPONGE,DUCT SCREW-MACHINE COVER-FAN,A ASSY-PCB,PFC BRACKET-PFC ASSY-LENS,MECHA BALLAST-PCB HOLDER-CHASSIS LCD ASSY-PCB,LCD CONTROL BRACKET-SENSOR SWITCH-LEVER SPACE-SPONGE,LCD ASSY-LAMP ASSY-PCB,LCD CONTROL COVER-LCD COVER-DUCT,IN,R ASSY-DUCT,IN COVER-DUCT,IN,L SPACE-SPONGE,LCD GRILLE-LAMP
Specification
-,SPT-403J,PLT51A,PAL,-,-,SP403JHA,PLT51A,-,-,EU ABS VO GRAY SP-403JHA,PLT51A,40,-,EC,TH,+,M3,L10,ZPC(YEL),SWRCH185 -,SVP-403J,P=0.72,PMMA,-,T=3.0 -,S40LW,HIPS,HB,BLK,-,SVP-403J,P=0.72,PMMA,-,T=3.0 -,SVP403J,HIPS,HB,BLK,TH,+,2,M4,L15,ZPC(BLK),SWRCH18 -,SVP403J,HIPS,HB,BLK,40,GLASS,3,-,SURFACE,779x460x -,SVP-403J,SECC-1,T1.6,BLK,RIG -,SVP-403J,SECC-1,T1.2,BLK,-,-,SVP-403J,SECC-1,T1.2,BLK,-,-,SVP-403J,SECC-1,T1.2,BLK,-,-,SVP-403J,SECC-1,T1.6,BLK,LEF -,SVP-403J,SECC-1,T1.2,BLK,-,PVC,HB,BLK,390,SVP403J,-,SVP-403J,SECC-1,T1.6,BLK,LEF -,SVP-403J,SECC-1,T1.2,BLK,-,,-,BLK,HB 720,SVP-403J,-,SVP-403J,SECC-1,T1.2,BLK,-,-,SVP-403J,SECC-1,T1.6,BLK,RIG HIPS V2 GRAY -,SVP403J,-,HIPS,V0,BLK,-,TH,+,2,M4,L15,ZPC(BLK),SWRCH18 -,VO,FAN,SVP403J -,SVP-403J,-,HIPS,VO,BLK,-,-,SVP-403J,-,HIPS,VO,BLK,-,-,SVP-403J,SECC-1,T1.0,-,-,125V/250V,15A/7.5A,95+-5C,85+-,SVP-403J,-,HIPS,VO,BLK,-,SPT-403J,-,PS,T0.5,BLK,-,T-,SPM-403J,-,HIPS,V2,GRAY,-,TH,+,2,M4,L15,ZPC(BLK),SWRCH18 -,SVP403J,SECC,T1.0,-,-,SPM-403J,-,PS,T0.5,BLK,-,-,SVP-403J,ABS,HB,BLK,PU FORM,T5,BLK,-,SVP403J,FH,M4,L15.5,ZPC(BLK),SWRC -,SPM-403J,-,HIPS,V2,GRAY,-,-,SP-403JHA,PLT51A,EC,-,SP403J -,-,DS001AKB-61B,SVP-403J -,ABS,VO,GRY,-,SVP-403J SP403J -,SP-403JHA,PLT51A,EC,-,-,L3300,SECC,T1.0,-,-,12V,100mA,SPDT,-,27deg SPONGE,VO,BLK -,SP-403JHA,PLT51A,EC,-,ABS VO BLK -,SVP-403J,-,HIPS,VO,BLK,-,-,VO,FAN,SVP403J -,SVP-403J,-,HIPS,VO,BLK,-,SPONGE,VO,BLK SECC-1 T0.5
Q'ty
1 1 1 1 1 2 1 2 18 2 1 1 1 1 1 1 1 3 1 1 1 1 1 1 1 4 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Remark
No
1 1-1 1-2 1-3 1-4 1-5 1-6 1-7 1-8 1-9 1-10 1-11 1-12 1-13 1-14 1-15 1-16
Code No
AA91-10308L AA64-30853E AA63-30128A AA61-20061A AA63-30127F AA64-10775A AA61-60004N AA61-20301A AA64-40381A AA64-70105A AA63-30177A AA63-30126B AA91-20056C AA91-60225A 6002-000522 AA95-90032Z AA95-90032Y AA94-00724A
Description
ASSY-CABINET,FRONT CABINET-FRONT COVER-GRILLE HOLDER-GRILLE COVER-HORN,L KNOB-POWER,MASTER SPRING-ES HOLDER-INDICATOR INDICATOR-LED BADGE-BRAND COVER-DUCT,BOT COVER-HORN,R ASSY-DOOR ASSY-HOLDER,SPK SCREW-TAPPING ASSY-PCB,MASTER ASSY-PCB,REMOCON ASSY-PCB,MAIN(OPT)
Specification
-,SPM403JHARX/NWT,PLT51A UKRAINE -,-,DG-703P,HIPS,HB,BLK,-,-,SVP-403J,-,HIPS,HB,BLK,-,-,S5288,NEOPRENE,HB,BLK,-,SP403JHAR,-,ABS,HB,BLK, -,SP403JHA,-,PC,-,VIOLET -,SUS304,0.6,OD8.1,H10,N5,-,-, -,SPM-403J,PC,VO,VIOLET,-,SVP403J,-,ACRYL,HB,CLEAR,AL,SS FLAT,SILVER,L70,-,-,-,SVP40LW,-,HIPS,HB,BLK,-,-,SP403JHA,DG703P,HIPS,HB,BLK, -,ABS HB,DG-703P,SPM403J -,PP,HB,BLK,8R20W,168BR20K TH,+,2,M4,L15,ZPC(BLK),SWRCH18 -,SP-403JHA,PLT51A,EC,-,-,SP-403JHA,PLT51A,EC,-,SP403JHARX/NWT,PLT51A,UKRANINE-
Q'ty
1 1 1 2 1 1 1 1 1 1 1 1 1 1 8 1 1 1
Remark
Samsung Electronics
7-1
Electric Parts List
8. Electric Parts List
8-1 SP403JHAX Parts List
Loc. No. Code No. Description ; Specification Remark Loc. No. Code No. Description ; Specification Remark
ASSY-PCB,MAIN(OPT)
* * * * * * * * * * * * * * * AB1 AF1 AF3 AF4 AT1 C101 C103 C104 C105 C107 C108 C109 C111 C112 C113 C114 C115 C116 C117 C119 C120 C121 C267 C270 C290 C296 C603 C604 C605 C606 C607 BUYER : SRSC AA94-00274A ASSY-PCB,MAIN(OPT);SP403JHARX/NWT, PLT51A,UKRAI BUYER : AMFO AA94-10148Y SSY-PCB,MAIN(OPT);SP403JHAX/AMF,PLT51A,NETHERAN BUYER : ANA AA94-10149HASSY-PCB,MAIN(OPT);SP403JHAX/ANA,PLT51A,RUMA BUYER : ATR AA94-10149F ASSY-PCB,MAIN(OPT);SP403JHAX/ATR,PLT51A,SWISS,BUYER : BOB AA94-10149J ASSY-PCB,MAIN(OPT);SP403JHAX/BOB,PLT51A,BULGARIA, BUYER : NSI AA94-10148WASSY-PCB,MAIN(OPT);SP403JHAX/NSI,PLT51A,DEN BUYER : ELS AA94-10149AASSY-PCB,MAIN(OPT);SP403JHAX/ELS,PLT51A,AUSTRIA,BUYER : EUP AA94-10149E ASSY-PCB,MAIN(OPT);SP403JHAX/EUP,PLT51A,CROATIA,BUYER : INT AA94-10149GASSY-PCB,MAIN(OPT);SP403JHAX/INT,PLT51A,SLOVENIA, BUYER : XEC AA94-10148UASSY-PCB,MAIN(OPT);SP403JHAX/XEC,PLT51A,SPAIN,BUYER : XEF AA94-10143R ASSY-PCB,MAIN(OPT);SP-403JHAX/XEF,PLT51A,FRANCE,BUYER : XEH AA94-10149DASSY-PCB,MAIN(OPT);SP403JHAX/XEH,PLT51A,HUNGARY,BUYER : XEO AA94-10149C ASSY-PCB,MAIN(OPT);SP403JHAX/XEO,PLT51A,POLAND,BUYER : XEU AA94-10148S ASSY-PCB,MAIN(OPT);SP403JHAX/XEU,PLT51A,U.K,BUYER : SEI AA94-10148T ASSY-PCB,MAIN(OPT);SP403JHAX/XET,PLT51A,ITALY,3711-002642 3711-002642 3711-002642 3711-002642 3711-002642 2305-000665 2305-000665 2401-000660 2305-000665 2305-000289 2401-000667 2401-002300 2201-000292 2401-000947 2201-000180 2201-000292 2201-000180 2401-001176 2201-000982 2401-000302 2401-000302 2401-002300 2201-000146 2201-000375 2201-000376 2201-000558 2401-000192 2301-000530 2401-000192 2301-000530 2401-000192 CONNECTOR-HEADER;BOX,3P,1R,2.5mm,STRAIGHT,SN CONNECTOR-HEADER;BOX,3P,1R,2.5mm,STRAIGHT,SN CONNECTOR-HEADER;BOX,3P,1R,2.5mm,STRAIGHT,SN CONNECTOR-HEADER;BOX,3P,1R,2.5mm,STRAIGHT,SN CONNECTOR-HEADER;BOX,3P,1R,2.5mm,STRAIGHT,SN C-FILM,MPEF;100nF,5%,63V,TP,7.5x4.0x5.0mm, C-FILM,MPEF;100nF,5%,63V,TP,7.5x4.0x5.0mm, C-AL;2.2uF,20%,50V,GP,TP,5x11,5 C-FILM,MPEF;100nF,5%,63V,TP,7.5x4.0x5.0mm, C-FILM,MPEF;220nF,5%,63V,TP,-,5mm C-AL;2.2uF,20%,50V,WT,TP,5x11,5 C-AL;47uF,20%,50V,GP,TP,6.3x11,5 C-CERAMIC,DISC;1nF,10%,50V,Y5P,TP,5x3,5 C-AL;22uF,20%,35V,GP,TP,5x11,5 C-CERAMIC,DISC;10nF,10%,50V,Y5V,TP,6.5*3,5 C-CERAMIC,DISC;1nF,10%,50V,Y5P,TP,5x3,5 C-CERAMIC,DISC;10nF,10%,50V,Y5V,TP,6.5*3,5 C-AL;33uF,20%,25V,GP,TP,5x11,5 C-CERAMIC,DISC;10nF,+80-20%,50V,Y5V,TP,6.5x3, C-AL;100uF,20%,25V,GP,TP,6.3x11,5 C-AL;100uF,20%,25V,GP,TP,6.3x11,5 C-AL;47uF,20%,50V,GP,TP,6.3x11,5 C-CERAMIC,DISC;100pF,5%,50V,SL,TP,5x3,5 C-CERAMIC,DISC;220pF,5%,50V,RH,TP,9.5x3.0,5 C-CERAMIC,DISC;220pF,5%,50V,SL,TP,4x4,5 C-CERAMIC,DISC;470pF,10%,50V,Y5P,TP,5x3,5 C-AL;1000uF,20%,50V,GP,TP,16x25,7.5 C-FILM,PEF;100nF,5%,100V,TP,11.5x12.5x6.5 C-AL;1000uF,20%,50V,GP,TP,16x25,7.5 C-FILM,PEF;100nF,5%,100V,TP,11.5x12.5x6.5 C-AL;1000uF,20%,50V,GP,TP,16x25,7.5
C608 C609 C610 C611 C621 C622 C623 C624 C629 C633 C634 C635 C636 C637 C638 C639 C831 C832 C833 C835 C836 C837 C838 C839 C840 C841 C842 C843 C851 C852 C863 C864 C866 C870 C901 C902 C903 C904 C905 CN704A CN705A CNM01 CNM02 CNM08 CNM09 CNM09A CNM10 CNM10A CNM11 CNM11A CNM12 CNM13 CNM14 CNM15 D101 D103 D104 D601 D602 D603 D901 D902 DZ102 DZ201 DZ202
2301-000530 C-FILM,PEF;100nF,5%,100V,TP,11.5x12.5x6.5 2401-000603 C-AL;1uF,20%,50V,GP,TP,5x11,5 2401-000318 C-AL;100uF,20%,25V,LZ,TP,8x11.5,5 2401-000603 C-AL;1uF,20%,50V,GP,TP,5x11,5 2301-000383 C-FILM,PEF;10nF,5%,50V,TP,6x7x3.2mm,5mm 2301-000383 C-FILM,PEF;10nF,5%,50V,TP,6x7x3.2mm,5mm 2301-000530 C-FILM,PEF;100nF,5%,100V,TP,11.5x12.5x6.5 2401-000603 C-AL;1uF,20%,50V,GP,TP,5x11,5 2401-000962 C-AL;22uF,20%,50V,GP,TP,5x11,5 2401-000480 C-AL;10uF,20%,50V,GP,TP,5x11,5 2305-000665 C-FILM,MPEF;100nF,5%,63V,TP,7.5x4.0x5.0mm, 2401-000480 C-AL;10uF,20%,50V,GP,TP,5x11,5 2401-000302 C-AL;100uF,20%,25V,GP,TP,6.3x11,5 2401-000302 C-AL;100uF,20%,25V,GP,TP,6.3x11,5 2401-000302 C-AL;100uF,20%,25V,GP,TP,6.3x11,5 2401-000302 C-AL;100uF,20%,25V,GP,TP,6.3x11,5 2401-002286 C-AL;470uF,20%,16V,WT,TP,10x12.5,5 2305-000665 C-FILM,MPEF;100nF,5%,63V,TP,7.5x4.0x5.0mm, 2401-003034 C-AL;220uF,20%,16V,WT,TP,8x11.5,5 2305-000665 C-FILM,MPEF;100nF,5%,63V,TP,7.5x4.0x5.0mm, 2401-002286 C-AL;470uF,20%,16V,WT,TP,10x12.5,5 2401-002286 C-AL;470uF,20%,16V,WT,TP,10x12.5,5 2305-000665 C-FILM,MPEF;100nF,5%,63V,TP,7.5x4.0x5.0mm, 2401-003034 C-AL;220uF,20%,16V,WT,TP,8x11.5,5 2401-003034 C-AL;220uF,20%,16V,WT,TP,8x11.5,5 2305-000665 C-FILM,MPEF;100nF,5%,63V,TP,7.5x4.0x5.0mm, 2401-000302 C-AL;100uF,20%,25V,GP,TP,6.3x11,5 2305-000665 C-FILM,MPEF;100nF,5%,63V,TP,7.5x4.0x5.0mm, 2305-000665 C-FILM,MPEF;100nF,5%,63V,TP,7.5x4.0x5.0mm, 2305-000665 C-FILM,MPEF;100nF,5%,63V,TP,7.5x4.0x5.0mm, 2401-001397 C-AL;470uF,20%,25V,GP,TP,10x16,5 2305-000665 C-FILM,MPEF;100nF,5%,63V,TP,7.5x4.0x5.0mm, 2401-002273 C-AL;220uF,20%,25V,HR,TP,10x20mm,5m 2305-000665 C-FILM,MPEF;100nF,5%,63V,TP,7.5x4.0x5.0mm, 2305-000665 C-FILM,MPEF;100nF,5%,63V,TP,7.5x4.0x5.0mm, 2401-000914 C-AL;22uF,20%,16V,GP,TP,5x11,5 2301-000383 C-FILM,PEF;10nF,5%,50V,TP,6x7x3.2mm,5mm 2401-002235 C-AL;10uF,20%,16V,GP,TP,5x11mm,5mm 2301-000452 C-FILM,PEF;47nF,5%,50V,TP,8x11x4.5mm,5mm 3710-001208 CONNECTOR-SOCKET;32P,2R,2.54mm,STRAIGHT,AUF 3710-001208 CONNECTOR-SOCKET;32P,2R,2.54mm,STRAIGHT,AUF 3711-002645 CONNECTOR-HEADER;BOX,6P,1R,2.5mm,STRAIGHT,SN 3711-003641 CONNECTOR-HEADER;BOX,12P,1R,2.5mm,STRAIGHT,SN 3711-001054 CONNECTOR-HEADER;BOX,6P,1R,2.5mm,STRAIGHT,SN 3711-003641 CONNECTOR-HEADER;BOX,12P,1R,2.5mm,STRAIGHT,SN AA39-20032C LEAD-CONNECTOR,ASSY;-,67096-012,S,12P,400,1007#26 3711-002645 CONNECTOR-HEADER;BOX,6P,1R,2.5mm,STRAIGHT,SN AA39-20038DLEAD-CONNECTOR,ASSY;-,67096-006,S,6P,300,1185#26 3711-002641 CONNECTOR-HEADER;BOX,10P,1R,2.54mm,STRAIGHT,Sn AA39-20025E LEAD-CONNECTOR,ASSY;-,67096-010,S,10P,400,1007#26 3711-000900 CONNECTOR-HEADER;BOX,3P,1R,2.5mm,STRAIGHT,SN 3711-002643 CONNECTOR-HEADER;BOX,4P,1R,2.5mm,STRAIGHT,SN 3711-003359 CONNECTOR-HEADER;BOX,10P,1R,2.5mm,STRAIGHT,SN 3711-000392 CONNECTOR-HEADER;3WALL,10P,1R,2.5mm,STRAIGHT,0401-000005 DIODE-SWITCHING;1N4148,75V,300mA,DO-35,TP 0401-001024 DIODE-SWITCHING;BAW75,25V,300mA,DO-35,TP 0401-001024 DIODE-SWITCHING;BAW75,25V,300mA,DO-35,TP 0401-000005 DIODE-SWITCHING;1N4148,75V,300mA,DO-35,TP 0401-000005 DIODE-SWITCHING;1N4148,75V,300mA,DO-35,TP 0401-000005 DIODE-SWITCHING;1N4148,75V,300mA,DO-35,TP 0401-000005 DIODE-SWITCHING;1N4148,75V,300mA,DO-35,TP 0401-000005 DIODE-SWITCHING;1N4148,75V,300mA,DO-35,TP 1203-000451 IC-VOLTAGE REGULATOR;33,TO-92,3P,-,PLASTIC,31/35V,2 0403-000297 DIODE-ZENER;MTZ6.2B,6.2V,5.96-6.27V,500mW, 0403-000297 DIODE-ZENER;MTZ6.2B,6.2V,5.96-6.27V,500mW,
Samsung Electronics
8-1
Electric Parts List
Loc. No.
Code No.
Description ; Specification
Remark
Loc. No.
Code No.
Description ; Specification
Remark
! ! ! ! ! ! ! ! !
DZ203 DZ205 DZ601 DZ602 DZ603 DZ604 FI102 FI103 FI105 IC101 IC601 IC604 IC802 IC803 IC805 IC806 IC904 IC905 J295 L101 L104 L105 L106 L107 L108 L109 L110 L113 L276 L277 L278 L279 L280 L601 L602 L901 Q101 Q102 Q104 Q105 Q602 Q603 Q901 Q902 Q903 Q904 Q905 R101 R102 R105 R106 R107 R109 R110 R111 R113 R116 R121 R122 R123 R124 R125 R126 R258 R259 R268 R269 R270 R601 R602 R603 R604 R605 R606 R607 R608 R609
0403-000296 DIODE-ZENER;MTZ5.6B,5.6V,5.45-5.73V,500mW, 0403-000296 DIODE-ZENER;MTZ5.6B,5.6V,5.45-5.73V,500mW, 0403-000654 DIODE-ZENER;MTZ12B,12V,11.44-12.03V,500mW, 0403-000654 DIODE-ZENER;MTZ12B,12V,11.44-12.03V,500mW, 0403-000654 DIODE-ZENER;MTZ12B,12V,11.44-12.03V,500mW, 0403-000654 DIODE-ZENER;MTZ12B,12V,11.44-12.03V,500mW, 2904-000301 FILTER-SAW AV;38.90MHz,SIP5K,ST,14.5dB,PAL-B 2903-000181 FILTER-CERAMIC;TR,5.5MHz,-,-,-,TP,TPS5.5MB-TF 2904-000302 FILTER-SAW AV;38.90MHz,-,ST,13.9dB,PAL-B/G,1204-001276 IC-SOUND PROCESSOR;TDA9810T,DIP,24P,400MIL,PLASTI 1201-001026 IC-POWER AMP;7265,ZIP,11P,19.6MIL,DUAL,1000 0801-000961 IC-CMOS LOGIC;4053,MUTIPLEXER,DIP,16P,300MIL 1203-000203 IC-POSI.ADJUST REG.;3050,TO-220,5P,-,PLASTIC,5V,1. 1203-000203 IC-POSI.ADJUST REG.;3050,TO-220,5P,-,PLASTIC,5V,1. 1203-000293 IC-POSI.FIXED REG.;7808,TO-220,3P,-,PLASTIC,7.7/8 1203-000298 IC-POSI.FIXED REG.;7809,TO-220,3P,-,PLASTIC,8.65/ 1001-001038 IC-ANALOG SWITCH;SAA1300,-,SOT-142,9P,-,SINGLE, 0904-001121 IC-I/O SUPPORT CHIP;8574,8BIT,DIP,16P,300MIL,100KH 2001-000812 R-CARBON;5.6Kohm,5%,1/8W,AA,TP,1.8x3.2m AA26-10006GTRANS-IF;-,7mG,VIF,-,7mm,8pF,77.8MHz,ST 2701-000101 INDUCTOR-AXIAL;1.2uH,10%,2.5x3.4mm 2701-000120 INDUCTOR-AXIAL;12uH,10%,2.5x3.4mm 2701-000115 INDUCTOR-AXIAL;10uH,10%,2.8x7mm 2701-000115 INDUCTOR-AXIAL;10uH,10%,2.8x7mm 2701-000115 INDUCTOR-AXIAL;10uH,10%,2.8x7mm 2701-000114 INDUCTOR-AXIAL;10uH,10%,2.5x3.4mm 2701-000114 INDUCTOR-AXIAL;10uH,10%,2.5x3.4mm 2701-000115 INDUCTOR-AXIAL;10uH,10%,2.8x7mm 2701-000114 INDUCTOR-AXIAL;10uH,10%,2.5x3.4mm 2701-000114 INDUCTOR-AXIAL;10uH,10%,2.5x3.4mm 2701-000146 INDUCTOR-AXIAL;2.2uH,10%,2.5x3.4mm 2701-000114 INDUCTOR-AXIAL;10uH,10%,2.5x3.4mm 2701-000114 INDUCTOR-AXIAL;10uH,10%,2.5x3.4mm 2701-000114 INDUCTOR-AXIAL;10uH,10%,2.5x3.4mm 2701-000114 INDUCTOR-AXIAL;10uH,10%,2.5x3.4mm 2701-000115 INDUCTOR-AXIAL;10uH,10%,2.8x7mm 0504-000137 TR-DIGITAL;KSR1202,PNP,300mW,10K-10K,TO-9 0504-000123 TR-DIGITAL;KSR1010,NPN,300mW,10K,TO-92,TP 0504-000123 TR-DIGITAL;KSR1010,NPN,300mW,10K,TO-92,TP 0501-000389 TR-SMALL SIGNAL;KSC815,NPN,400mW,TO-92,TP,1200504-000123 TR-DIGITAL;KSR1010,NPN,300mW,10K,TO-92,TP 0504-000123 TR-DIGITAL;KSR1010,NPN,300mW,10K,TO-92,TP 0501-000389 TR-SMALL SIGNAL;KSC815,NPN,400mW,TO-92,TP,1200504-000117 TR-DIGITAL;KSR1002,NPN,300mW,10K-10K,TO-9 0504-000117 TR-DIGITAL;KSR1002,NPN,300mW,10K-10K,TO-9 0504-000117 TR-DIGITAL;KSR1002,NPN,300mW,10K-10K,TO-9 0501-000283 TR-SMALL SIGNAL;KSA539,PNP,400mW,TO-92,TP,1202001-000522 R-CARBON;22Kohm,5%,1/8W,AA,TP,1.8x3.2mm 2001-000522 R-CARBON;22Kohm,5%,1/8W,AA,TP,1.8x3.2mm 2001-000290 R-CARBON;10Kohm,5%,1/8W,AA,TP,1.8x3.2mm 2001-000660 R-CARBON;33Kohm,5%,1/8W,AA,TP,1.8x3.2mm 2001-000331 R-CARBON;12Kohm,5%,1/8W,AA,TP,1.8x3.2mm 2001-000490 R-CARBON;200ohm,5%,1/8W,AA,TP,1.8x3.2mm 2001-000734 R-CARBON;4.7Kohm,5%,1/8W,AA,TP,1.8x3.2m 2001-000515 R-CARBON;220ohm,5%,1/8W,AA,TP,1.8x3.2mm 2001-001138 R-CARBON(S);390ohm,5%,1/2W,AA,TP,2.4x6.4mm 2001-000969 R-CARBON;75ohm,5%,1/8W,AA,TP,1.8x3.2mm 2001-000522 R-CARBON;22Kohm,5%,1/8W,AA,TP,1.8x3.2mm 2001-000857 R-CARBON;560ohm,5%,1/8W,AA,TP,1.8x3.2mm 2001-000241 R-CARBON;1.5Kohm,5%,1/8W,AA,TP,1.8x3.2m 2001-000241 R-CARBON;1.5Kohm,5%,1/8W,AA,TP,1.8x3.2m 2001-000429 R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm 2001-000362 R-CARBON;150ohm,5%,1/8W,AA,TP,1.8x3.2mm 2001-000302 R-CARBON;10ohm,5%,1/8W,AA,TP,1.8x3.2mm 2001-000302 R-CARBON;10ohm,5%,1/8W,AA,TP,1.8x3.2mm 2001-000302 R-CARBON;10ohm,5%,1/8W,AA,TP,1.8x3.2mm 2001-000302 R-CARBON;10ohm,5%,1/8W,AA,TP,1.8x3.2mm 2001-000302 R-CARBON;10ohm,5%,1/8W,AA,TP,1.8x3.2mm 2001-001055 R-CARBON(S);1.8Kohm,5%,1/2W,AA,TP,2.4x6.4m 2001-001055 R-CARBON(S);1.8Kohm,5%,1/2W,AA,TP,2.4x6.4m 2001-001146 R-CARBON(S);4.7ohm,5%,1/2W,AA,TP,2.4x6.4mm 2001-001055 R-CARBON(S);1.8Kohm,5%,1/2W,AA,TP,2.4x6.4m 2001-000290 R-CARBON;10Kohm,5%,1/8W,AA,TP,1.8x3.2mm 2001-001146 R-CARBON(S);4.7ohm,5%,1/2W,AA,TP,2.4x6.4mm 2001-000290 R-CARBON;10Kohm,5%,1/8W,AA,TP,1.8x3.2mm 2001-000628 R-CARBON;300ohm,5%,1/8W,AA,TP,1.8x3.2mm 2001-000628 R-CARBON;300ohm,5%,1/8W,AA,TP,1.8x3.2mm
R621 R622 R623 R624 R626 R630 R631 R901 R902 R903 R904 R905 R906 R907 R908 R909 R910 R911 R912 R913 R914 R915 R916 R917 R925 R926 R927 R928 R929 R930 R933 TU01 VR101 VR102
2001-000429 R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm 2001-000429 R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm 2001-000290 R-CARBON;10Kohm,5%,1/8W,AA,TP,1.8x3.2mm 2001-000273 R-CARBON;100Kohm,5%,1/8W,AA,TP,1.8x3.2m 2001-000522 R-CARBON;22Kohm,5%,1/8W,AA,TP,1.8x3.2mm 2001-001055 R-CARBON(S);1.8Kohm,5%,1/2W,AA,TP,2.4x6.4m 2001-000109 R-CARBON(S);470ohm,5%,1/2W,AA,TP,2.4x6.4mm 2001-000577 R-CARBON;2Kohm,5%,1/8W,AA,TP,1.8x3.2mm 2001-000577 R-CARBON;2Kohm,5%,1/8W,AA,TP,1.8x3.2mm 2001-000290 R-CARBON;10Kohm,5%,1/8W,AA,TP,1.8x3.2mm 2001-000290 R-CARBON;10Kohm,5%,1/8W,AA,TP,1.8x3.2mm 2001-000734 R-CARBON;4.7Kohm,5%,1/8W,AA,TP,1.8x3.2m 2001-000290 R-CARBON;10Kohm,5%,1/8W,AA,TP,1.8x3.2mm 2001-000273 R-CARBON;100Kohm,5%,1/8W,AA,TP,1.8x3.2m 2001-000429 R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm 2001-000429 R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm 2001-000429 R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm 2001-001097 R-CARBON(S);2.4Kohm,5%,1/2W,AA,TP,2.4x6.4m 2001-000734 R-CARBON;4.7Kohm,5%,1/8W,AA,TP,1.8x3.2m 2001-000281 R-CARBON;100ohm,5%,1/8W,AA,TP,1.8x3.2mm 2001-000281 R-CARBON;100ohm,5%,1/8W,AA,TP,1.8x3.2mm 2001-000109 R-CARBON(S);470ohm,5%,1/2W,AA,TP,2.4x6.4mm 2001-000109 R-CARBON(S);470ohm,5%,1/2W,AA,TP,2.4x6.4mm 2001-000109 R-CARBON(S);470ohm,5%,1/2W,AA,TP,2.4x6.4mm 2001-000734 R-CARBON;4.7Kohm,5%,1/8W,AA,TP,1.8x3.2m 2001-000290 R-CARBON;10Kohm,5%,1/8W,AA,TP,1.8x3.2mm 2001-000290 R-CARBON;10Kohm,5%,1/8W,AA,TP,1.8x3.2mm 2001-000281 R-CARBON;100ohm,5%,1/8W,AA,TP,1.8x3.2mm 2001-000281 R-CARBON;100ohm,5%,1/8W,AA,TP,1.8x3.2mm 2001-000429 R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm 2001-000812 R-CARBON;5.6Kohm,5%,1/8W,AA,TP,1.8x3.2m AA40-10005P TUNER-B/S;TELE9-042A,PAL-B/G,TR,181 CH 2103-000672 VR-SEMI;20Kohm,25%,1/5W,TOP 2103-000676 VR-SEMI;50Kohm,25%,1/5W,TOP
ASSY-PCB,POWER
* C801 C802 C804 C805 C807 C816 C817 C818 C819 C820 C823 C824 C825 C826 C827 C828 C829 C830 C831 C832 C833 C834 C835 C836 C837 C838 C839 C840 C841 C842 C843 C844 C845 C846 C847 C848 C849 AA95-10010X ASSY-PCB,POWER;SP-403JHA,PLT51A,40,-,EC,2306-000321 2306-000321 2201-000315 2201-000315 2401-003031 2303-000159 2401-002289 2401-000851 2301-000192 2401-002262 2201-000551 2401-000737 2401-000192 2201-000551 2401-002231 2401-001115 2401-001115 2201-000551 2401-000136 2401-000689 2201-000551 2401-001661 2401-000384 2201-000551 2401-002215 2401-000703 2401-001397 2305-000412 2201-000332 2201-000332 2401-001563 2401-002292 2401-001363 2401-002144 2401-002594 2201-000556 2401-000611 C-FILM,MPPF;470nF,5%,275V,TP,-,22.5mm C-FILM,MPPF;470nF,5%,275V,TP,-,22.5mm C-CERAMIC,DISC;2.2nF,+80-20%,250VAC,Y5U,TP,9x C-CERAMIC,DISC;2.2nF,+80-20%,250VAC,Y5U,TP,9x C-AL;470uF,20%,450V,GP,BK,35x45mm,1 C-FILM,PPF;2.2nF,5%,1.6KV,BK,31x15.5x8.5, C-AL;470uF,20%,35V,WT,TP,10x20,5 C-AL;220uF,20%,35V,HR,TP,13x25,5 C-FILM,PEF;1nF,5%,50V,TP,5.3x10mm,5mm C-AL;10uF,20%,160V,WT,TP,10x20,5 C-CERAMIC,DISC;470pF,10%,1KV,Y5P,TP,8x5,5 C-AL;2200uF,20%,50V,GP,TP,18x35.5,7 C-AL;1000uF,20%,50V,GP,TP,16x25,7.5 C-CERAMIC,DISC;470pF,10%,1KV,Y5P,TP,8x5,5 C-AL;470uF,20%,50V,WT,TP,13x20mm,5m C-AL;330uF,20%,25V,GP,TP,10x12.5,5 C-AL;330uF,20%,25V,GP,TP,10x12.5,5 C-CERAMIC,DISC;470pF,10%,1KV,Y5P,TP,8x5,5 C-AL;1000uF,20%,16V,LZ,TP,13x20,5 C-AL;2200uF,20%,16V,GP,TP,13x25,5 C-CERAMIC,DISC;470pF,10%,1KV,Y5P,TP,8x5,5 C-AL;68uF,20%,100V,GP,TP,10x16,5 C-AL;10uF,20%,100V,GP,TP,6.3x11,5mm C-CERAMIC,DISC;470pF,10%,1KV,Y5P,TP,8x5,5 C-AL;2200uF,20%,25V,WT,TP,13x25,5 C-AL;2200uF,20%,25V,GP,-,12.5x25mm, C-AL;470uF,20%,25V,GP,TP,10x16,5 C-FILM,MPEF;470nF,5%,63V,TP,-,5mm C-CERAMIC,DISC;2.2nF,20%,250VAC,Y5U,TP,11x7,7 C-CERAMIC,DISC;2.2nF,20%,250VAC,Y5U,TP,11x7,7 C-AL;47uF,20%,400V,GP,TP,16x25,7.5 C-AL;47uF,20%,25V,WT,TP,8X11,5 C-AL;470uF,20%,16V,GP,TP,10x12.5,5 C-AL;47uF,20%,16V,GP,TP,5x11,5 C-AL;220uF,20%,16V,GP,TP,8x11.5,5 C-CERAMIC,DISC;470pF,10%,500V,Y5P,TP,7x4,5 C-AL;1uF,20%,50V,WT,TP,5x11,5
8-2
Samsung Electronics
Electric Parts List
Loc. No.
Code No.
Description ; Specification
Remark
Loc. No.
Code No.
Description ; Specification
Remark
!
!
!
! ! ! ! ! ! ! !
! !
C850 C851 C852 C853 C854 C855 CNP01 CNP01A CNP02 CNP02A CNP03 CNP03A D803 D808 D811 D812 D813 D814 D815 D816 D817 D818 D819 D820 D821 D822 D823 D825 D826 D827 D828 D829 D830 D831 D832 F801 F801A F801B F802 F802A F802B F803 F803A F803B F805 IC802 IC803 IC805 IC806 IC807 IC808 IC809 JP801A L801 L802 L803 L804 L805 L806 L807 L808 L809 L810 L811 L812 L813 L816 L817 L818 L819 P802F P805D P807A Q801 Q804 R801 R802
2401-002215 C-AL;2200uF,20%,25V,WT,TP,13x25,5 2401-002215 C-AL;2200uF,20%,25V,WT,TP,13x25,5 2401-001333 C-AL;470nF,20%,50V,GP,TP,5x11,5 2401-001333 C-AL;470nF,20%,50V,GP,TP,5x11,5 2201-000990 C-CERAMIC,DISC;4.7nF,20%,400V,Y5U,BK,7x16,10m 2201-000990 C-CERAMIC,DISC;4.7nF,20%,400V,Y5U,BK,7x16,10m 3711-002645 CONNECTOR-HEADER;BOX,6P,1R,2.5mm,STRAIGHT,SN AA39-20027C LEAD-CONNECTOR,ASSY;-,67096-006,S,6P,500,1007#26 3711-003641 CONNECTOR-HEADER;BOX,12P,1R,2.5mm,STRAIGHT,SN AA39-20032E LEAD-CONNECTOR,ASSY;-,67096-012,S,12P,600,1007#26 3711-002647 CONNECTOR-HEADER;BOX,8P,1R,2.5mm,STRAIGHT,SN AA39-20030DLEAD-CONNECTOR,ASSY;-,67096-008,S,8P,600,1007#26 0402-000549 DIODE-BRIDGE;RBV606,600V,6A,-,BK 0402-000213 DIODE-RECTIFIER;ERB12-06,600V,1.0A,DO-41,TP 0402-000546 DIODE-RECTIFIER;TVR10G,400V,1.0A,DO-41,TP 0402-000546 DIODE-RECTIFIER;TVR10G,400V,1.0A,DO-41,TP 0402-000546 DIODE-RECTIFIER;TVR10G,400V,1.0A,DO-41,TP 0403-000704 DIODE-ZENER;TZP7.5B,7.5V,7.5-8.4V,1W,DO-41 0402-000546 DIODE-RECTIFIER;TVR10G,400V,1.0A,DO-41,TP 0402-000546 DIODE-RECTIFIER;TVR10G,400V,1.0A,DO-41,TP 0402-000233 DIODE-RECTIFIER;FML-G12S,200V,5A,-,0402-000546 DIODE-RECTIFIER;TVR10G,400V,1.0A,DO-41,TP 0402-000233 DIODE-RECTIFIER;FML-G12S,200V,5A,-,0402-000546 DIODE-RECTIFIER;TVR10G,400V,1.0A,DO-41,TP 0402-000233 DIODE-RECTIFIER;FML-G12S,200V,5A,-,0403-000656 DIODE-ZENER;MTZ15C,15V,14.35-15.09V,500mW, 0402-000546 DIODE-RECTIFIER;TVR10G,400V,1.0A,DO-41,TP 0402-000132 DIODE-RECTIFIER;1N4004,400V,1A,DO-41,TP 0402-000102 DIODE-BRIDGE;D2SB60,600V,1.5A,0406-001007 DIODE-TVS;P6KE180A,171/180/189V,600W,CAS 0402-000243 DIODE-RECTIFIER;RC2-V1,2000V,0.2A,DO-201 0401-000005 DIODE-SWITCHING;1N4148,75V,300mA,DO-35,TP 0402-000534 DIODE-RECTIFIER;RG10V,400V,1.2A,DO-201,TP 0402-000546 DIODE-RECTIFIER;TVR10G,400V,1.0A,DO-41,TP 0402-000233 DIODE-RECTIFIER;FML-G12S,200V,5A,-,3601-001007 FUSE-FERRULE;250V,6.3A,TL,GLASS,5.2x20mm 3602-000114 FUSE-HOLDER;-,-,30mohm 3602-000114 FUSE-HOLDER;-,-,30mohm 3601-000261 FUSE-FERRULE;250V,3.15A,TL,GLASS,5.2x20mm 3602-000114 FUSE-HOLDER;-,-,30mohm 3602-000114 FUSE-HOLDER;-,-,30mohm 3601-000261 FUSE-FERRULE;250V,3.15A,TL,GLASS,5.2x20mm 3602-000114 FUSE-HOLDER;-,-,30mohm 3602-000114 FUSE-HOLDER;-,-,30mohm 3601-001086 FUSE-FERRULE;125V,5A,FA,GLASS,2.4x7.5mm AA13-20002K IC-HYBRID;-,STR-S6709 LF953,SIP,9P,SMPS 1203-001583 IC-SWITCH VOL. REG.;801,SIP,10P,157MIL,PLASTIC,5/9 1203-000203 IC-POSI.ADJUST REG.;3050,TO-220,5P,-,PLASTIC,5V,1. 1203-001197 IC-POWER PRESCALER;012,SIP,3P,TO-220,PLASTIC,12V, 1203-000640 IC-PWM CONTROLLER;210,DIP,8P,245MIL,PLASTIC,12V, 1203-000203 IC-POSI.ADJUST REG.;3050,TO-220,5P,-,PLASTIC,5V,1. 0604-001038 PHOTO-COUPLER;TR,130-260%,200mW,DIP-4,ST AA39-20010ALEAD CONNECTOR-ASSY;-,YFH800-01,S,1P,200,1617#22 AA29-30002DFILTER-LINE;-,10mH,2.8A,-,SQE-3535H AA29-30002DFILTER-LINE;-,10mH,2.8A,-,SQE-3535H AA27-10001C COIL-CHOKE;-,100uH,K,-,5.0A,ST,700UH-K(RO 3301-000287 CORE-FERRITE BEAD;AA,3.5x1.0x6.0mm,1500,2400G 3301-000287 CORE-FERRITE BEAD;AA,3.5x1.0x6.0mm,1500,2400G 3301-000287 CORE-FERRITE BEAD;AA,3.5x1.0x6.0mm,1500,2400G AA27-10001UCOIL-CHOKE;-,20uH,K,-,2A,-,20UH-K(2A),12x 3301-000287 CORE-FERRITE BEAD;AA,3.5x1.0x6.0mm,1500,2400G AA27-10001UCOIL-CHOKE;-,20uH,K,-,2A,-,20UH-K(2A),12x 2701-000112 INDUCTOR-AXIAL;100uH,10%,2.8x7mm 3301-000287 CORE-FERRITE BEAD;AA,3.5x1.0x6.0mm,1500,2400G AA27-10001C COIL-CHOKE;-,100uH,K,-,5.0A,ST,700UH-K(RO 3301-000287 CORE-FERRITE BEAD;AA,3.5x1.0x6.0mm,1500,2400G 3301-000287 CORE-FERRITE BEAD;AA,3.5x1.0x6.0mm,1500,2400G AA27-10002L COIL-CHOKE;-,24uH,K,-,2A,-,24UH-K,10x10mm AA27-10001Y COIL-CHOKE;-,100uH,K,25,1A,-,100UH-K(1.0A AA27-10001Y COIL-CHOKE;-,100uH,K,25,1A,-,100UH-K(1.0A AA39-20010B LEAD-CONNECTOR,ASSY;-,YFH800-01,S,1P,500,1617#22 AA39-20176E LEAD CONNECTOR-ASSY;-,YFH800-03,S,3(2)P,500mm,1617 AA39-20010B LEAD-CONNECTOR,ASSY;-,YFH800-01,S,1P,500,1617#22 0503-000153 TR-DARLINGTON;TIP102,NPN,2W,TO-220,TP,1000-2 0501-000369 TR-SMALL SIGNAL;KSC2331-Y,NPN,1W,TO-92L,-,1202002-001011 R-COMPOSITION;3.3Mohm,10%,1/2W,AA,TP,3.7x9mm 1404-001045 THERMISTOR-NTC;4.7ohm,15%,2900K,35.0mW,TP
R806 R807 R812 R813 R814 R815 R816 R817 R818 R819 R820 R821 R822 R823 R826 R827 R828 R831 R832 R833 R834 R835 R836 R838 R839 R840 R841 R842 R843 REL801 ! T801 ! T802 V801 V802 V803
2001-001129 R-CARBON(S);330Kohm,5%,1/2W,AA,TP,2.4x6.4m 2001-001129 R-CARBON(S);330Kohm,5%,1/2W,AA,TP,2.4x6.4m 2003-001090 R-METAL OXIDE(S);10Kohm,5%,2W,AF,TP,4x12mm 2003-001090 R-METAL OXIDE(S);10Kohm,5%,2W,AF,TP,4x12mm 2006-000307 R-CEMENT;20ohm,5%,5W,CH,BK,9.5x27x9.5mm 2003-001090 R-METAL OXIDE(S);10Kohm,5%,2W,AF,TP,4x12mm 2001-001088 R-CARBON(S);1Kohm,5%,1/2W,AA,TP,2.4x6.4mm 2001-001093 R-CARBON(S);2.2Kohm,5%,1/2W,AA,TP,2.4x6.4m 2001-001143 R-CARBON(S);4.3Kohm,5%,1/2W,AA,TP,2.4x6.4m 2001-001410 R-CARBON(S);43ohm,5%,1/2W,AA,TP,2.4x6.4mm 2001-001117 R-CARBON(S);2Kohm,5%,1/2W,AA,TP,2.4x6.4mm 2001-001117 R-CARBON(S);2Kohm,5%,1/2W,AA,TP,2.4x6.4mm 2009-000021 R-METAL PLATE;0.33ohm,10%,5W,CL,TP,5x14x18mm 2001-001117 R-CARBON(S);2Kohm,5%,1/2W,AA,TP,2.4x6.4mm 2008-000270 R-FUSIBLE;3.3ohm,5%,1/2W,AA,TP,4.7x11mm 2002-001013 R-COMPOSITION;4.7Mohm,10%,1/2W,AA,TP,3.7x9mm 2002-001013 R-COMPOSITION;4.7Mohm,10%,1/2W,AA,TP,3.7x9mm 2008-000270 R-FUSIBLE;3.3ohm,5%,1/2W,AA,TP,4.7x11mm 2001-000052 R-CARBON(S);3.3Kohm,5%,1/2W,AA,TP,2.4x6.4m 2001-001088 R-CARBON(S);1Kohm,5%,1/2W,AA,TP,2.4x6.4mm 2001-000109 R-CARBON(S);470ohm,5%,1/2W,AA,TP,2.4x6.4mm 2001-001096 R-CARBON(S);2.2ohm,5%,1/2W,AA,TP,2.4x6.4mm 2001-000109 R-CARBON(S);470ohm,5%,1/2W,AA,TP,2.4x6.4mm 2001-001088 R-CARBON(S);1Kohm,5%,1/2W,AA,TP,2.4x6.4mm 2001-001116 R-CARBON(S);27ohm,5%,1/2W,AA,TP,2.4x6.4mm 2008-000179 R-FUSIBLE(S);10ohm,5%,1/2W,AA,TP,2.5x6.5mm 2001-001106 R-CARBON(S);220Kohm,5%,1/2W,AA,TP,2.4x6.4m 2001-001112 R-CARBON(S);24Kohm,5%,1/2W,AA,TP,2.4x6.4mm 2001-000085 R-CARBON(S);100Kohm,5%,1/2W,AA,TP,2.4x6.4m 3501-001053 RELAY-POWER;5Vdc,530mW,10A,1FormA,15mS,5mS AA26-20007T TRANS-SWITCHING;-,AC80V~AC280V,34/36/12/8/8,-, AA26-20004MTRANS-SWITCHING;-,90~260V,KS,EE2118,7.92MH,-,C 1405-000152 VARISTOR;560V,2500A,14x8.5mm,TP 1405-000152 VARISTOR;560V,2500A,14x8.5mm,TP 1405-000152 VARISTOR;560V,2500A,14x8.5mm,TP
ASSY-SOUND
* C601 C602 C603 C604 C605 C606 C610 C611 C612 C613 C614 C615 C616 C617 C618 C619 C620 C621 C622 C623 C624 C625 C626 C627 C628 C629 C630 C631 C632 C633 C634 C635 C636 C637 C638 C639 AA95-40009Z ASSY-SOUND;-,CW764AHD,SCT53A,DOLBY,3D,2203-000192 2203-000192 2401-001840 2401-001840 2401-000480 2203-000979 2401-000603 2401-000590 2203-000716 2203-000716 2401-002235 2203-000595 2203-000938 2203-000142 2203-000444 2203-000444 2401-000603 2401-000603 2203-000701 2203-000701 2203-001077 2203-001077 2401-002235 2203-000938 2203-000142 2203-001077 2401-002235 2203-000192 2203-000753 2203-000753 2203-000784 2203-000784 2203-000192 2401-001026 2401-002235 2401-002235 C-CERAMIC,CHIP;100nF,+80-20%,50V,Y5V,TP,2012, C-CERAMIC,CHIP;100nF,+80-20%,50V,Y5V,TP,2012, C-AL;100uF,20%,16V,GP,TP,6.3x11,5 C-AL;100uF,20%,16V,GP,TP,6.3x11,5 C-AL;10uF,20%,50V,GP,TP,5x11,5 C-CERAMIC,CHIP;47nF,10%,50V,X7R,TP,2012,C-AL;1uF,20%,50V,GP,TP,5x11,5 C-AL;1uF,20%,50V,GP,TP,3x5,5 C-CERAMIC,CHIP;3.3nF,10%,50V,X7R,TP,2012,C-CERAMIC,CHIP;3.3nF,10%,50V,X7R,TP,2012,C-AL;10uF,20%,16V,GP,TP,5x11mm,5mm C-CERAMIC,CHIP;220pF,5%,50V,NPO,TP,2012,C-CERAMIC,CHIP;470pF,5%,50V,NPO,TP,2012,C-CERAMIC,CHIP;1.5nF,10%,50V,X7R,TP,2012,C-CERAMIC,CHIP;1nF,10%,50V,X7R,TP,2012,C-CERAMIC,CHIP;1nF,10%,50V,X7R,TP,2012,C-AL;1uF,20%,50V,GP,TP,5x11,5 C-AL;1uF,20%,50V,GP,TP,5x11,5 C-CERAMIC,CHIP;2pF,0.25pF,50V,NPO,TP,2012,C-CERAMIC,CHIP;2pF,0.25pF,50V,NPO,TP,2012,C-CERAMIC,CHIP;56pF,5%,50V,NPO,TP,2012,C-CERAMIC,CHIP;56pF,5%,50V,NPO,TP,2012,C-AL;10uF,20%,16V,GP,TP,5x11mm,5mm C-CERAMIC,CHIP;470pF,5%,50V,NPO,TP,2012,C-CERAMIC,CHIP;1.5nF,10%,50V,X7R,TP,2012,C-CERAMIC,CHIP;56pF,5%,50V,NPO,TP,2012,C-AL;10uF,20%,16V,GP,TP,5x11mm,5mm C-CERAMIC,CHIP;100nF,+80-20%,50V,Y5V,TP,2012, C-CERAMIC,CHIP;330nF,+80-20%,50V,Y5V,TP,3216, C-CERAMIC,CHIP;330nF,+80-20%,50V,Y5V,TP,3216, C-CERAMIC,CHIP;330pF,5%,50V,NPO,TP,2012,2mm C-CERAMIC,CHIP;330pF,5%,50V,NPO,TP,2012,2mm C-CERAMIC,CHIP;100nF,+80-20%,50V,Y5V,TP,2012, C-AL;3.3uF,20%,50V,GP,TP,5x11,5 C-AL;10uF,20%,16V,GP,TP,5x11mm,5mm C-AL;10uF,20%,16V,GP,TP,5x11mm,5mm
Samsung Electronics
8-3
Electric Parts List
Loc. No.
Code No.
Description ; Specification
Remark
Loc. No.
Code No.
Description ; Specification
Remark
C640 C641 C642 C643 C644 C645 C646 C647 C648 C649 C650 C651 C653 C654 C655 C656 C657 C658 C659 C660 C661 C662 C663 C664 C665 C666 C667 C668 C669 C670 C671 C672 C679 C680 C681 C682 C683 C684 C685 C688 C691 C692 C694 C695 C696 C697 CD601 CD602 CD603 CD604 CD605 CD