Text preview for : Samsung TXM2790FX-XAA (Chassis KS3A(N)) (Service Manual).pdf part of Samsung TXM2790FX/XAA Samsung TXM2790FX/XAA (Chassis KS3A(N)) (Service Manual)
Back to : Samsung TXM2790FX-XAA (Ch | Home
COLOR TELEVISION RECEIVER
Chassis : KS3A(N) Model : TXM2790FX/XAA
COLOR TELEVISION RECEIVER
CONTENTS
1. Precautions 2. Reference Information 3. Specifications 4. Alignment and Adjustments 5. Troubleshooting 6. Exploded Views and Parts List 7. Electrical Parts List 8. Block Diagrams 9. Wiring Diagram 10. Schematic Diagrams
ELECTRONICS
© Samsung Electronics Co., Ltd. JUN . 2002
Printed in Korea AA82-00055A
Precautions
1. Precautions
Follow these safety, servicing and ESD precautions to prevent damage and protect against potential hazards such as electrical shock and X-rays.
1-1 Safety Precautions
1. Be sure that all of the built-in protective devices are replaced. Restore any missing protective shields. 2. When reinstalling the chassis and its assemblies, be sure to restore all protective devices, including: nonmetallic control knobs and compartment covers. 3. Make sure that there are no cabinet openings through which people--particularly children--might insert fingers and contact dangerous voltages. Such openings include the spacing between the picture tube and the cabinet mask, excessively wide cabinet ventilation slots, and improperly fitted back covers. If the measured resistance is less than 1.0 megohm or greater than 5.2 megohms, an abnormality exists that must be corrected before the unit is returned to the customer. 4. Leakage Current Hot Check (Figure 1-1): Warning: Do not use an isolation transformer during this test. Use a leakagecurrent tester or a metering system that complies with American National Standards Institute (ANIS C101.1, Leakage Current for Appliances), and Underwriters Laboratories (UL Publication UL1410, 59.7). 5. With the unit completely reassembled, plug the AC line cord directly into the power outlet. With the unit's AC switch first in the ON position and then OFF, measure the current between a known earth ground (metal water pipe, conduit, etc.) and all exposed metal parts, including: antennas, handle brackets, metal cabinets, screwheads and control shafts. The current measured should not exceed 0.5 milliamp. Reverse the powerplug prongs in the AC outlet and repeat the test.
DEVICE UNDER TEST TEST ALL EXPOSED METAL SURFACES 2-WIRE CORD ALSO TEST WITH PLUG REVERSED (USING AC ADAPTER PLUG AS REQUIRED)
LEAKAGE CURRENT TESTER
(READING SHOULD NOT BE ABOVE 0.5mA)
EARTH GROUND
Fig. 1-1 AC Leakage Test 6. Antenna Cold Check: With the unit's AC plug disconnected from the AC source, connect an electrical jumper across the two AC prongs. Connect one lead of the ohmmeter to an AC prong. Connect the other lead to the coaxial connector. 7. X-ray Limits: The picture tube is especially designed to prohibit X-ray emissions. To ensure continued X-ray protection, replace the picture tube only with one that is the same type as the original. Carefully reinstall the picture tube shields and mounting hardware; these also provide X-ray protection. 8. High Voltage Limits: High voltage must be measured each time servicing is done on the B+, horizontal deflection or high voltage circuits. Correct operation of the X-ray protection circuits must be reconfirmed whenever they are serviced. (X-ray protection circuits also may be called "horizontal disable" or "hold-down".) Heed the high voltage limits. These include the Xray Protection Specifications Label, and the Product Safety and X-ray Warning Note on the service data schematic.
Samsung Electronics
1-1
Precautions
1-1 Safety Precautions (Continued)
9. High voltage is maintained within specified limits by close-tolerance, safety-related components and adjustments. If the high voltage exceeds the specified limits, check each of the special components. 10. Design Alteration Warning: Never alter or add to the mechanical or electrical design of this unit. Example: Do not add auxiliary audio or video connectors. Such alterations might create a safety hazard. Also, any design changes or additions will void the manufacturer's warranty. 11. Hot Chassis Warning: Some TV receiver chassis are electrically connected directly to one conductor of the AC power cord. If an isolation transformer is not used, these units may be safely serviced only if the AC power plug is inserted so that the chassis is connected to the ground side of the AC source. To confirm that the AC power plug is inserted correctly, do the following: Using an AC voltmeter, measure the voltage between the chassis and a known earth ground. If the reading is greater than 1.0V, remove the AC power plug, reverse its polarity and reinsert. Re-measure the voltage between the chassis and ground. 12. Some TV chassis are designed to operate with 85 volts AC between chassis and ground, regardless of the AC plug polarity. These units can be safely serviced only if an isolation transformer inserted between the receiver and the power source. 13. Some TV chassis have a secondary ground system in addition to the main chassis ground. This secondary ground system is not isolated from the AC power line. The two ground systems are electrically separated by insulating material that must not be defeated or altered. 14. Components, parts and wiring that appear to have overheated or that are otherwise damaged should be replaced with parts that meet the original specifications. Always determine the cause of damage or overheating, and correct any potential hazards. 15. Observe the original lead dress, especially near the following areas: Antenna wiring, sharp edges, and especially the AC and high voltage power supplies. Always inspect for pinched, out-of-place, or frayed wiring. Do not change the spacing between components and the printed circuit board. Check the AC power cord for damage. Make sure that leads and components do not touch thermally hot parts. 16. Picture Tube Implosion Warning: The picture tube in this receiver employs "integral implosion" protection. To ensure continued implosion protection, make sure that the replacement picture tube is the same as the original. 17. Do not remove, install or handle the picture tube without first putting on shatterproof goggles equipped with side shields. Never handle the picture tube by its neck. Some "in-line" picture tubes are equipped with a permanently attached deflection yoke; do not try to remove such "permanently attached" yokes from the picture tube. 18. Product Safety Notice: Some electrical and mechanical parts have special safety-related characteristics which might not be obvious from visual inspection. These safety features and the protection they give might be lost if the replacement component differs from the original--even if the replacement is rated for higher voltage, wattage, etc. Components that are critical for safety are indicated in the circuit diagram by shading, ( ) or ( ). Use replacement components that have the same ratings, especially for flame resistance and dielectric strength specifications. A replacement part that does not have the same safety characteristics as the original might create shock, fire or other hazards.
1-2
Samsung Electronics
Precautions
1-2 Servicing Precautions
Warning1: First read the "Safety Precautions" section of this manual. If some unforeseen circumstance creates a conflict between the servicing and safety precautions, always follow the safety precautions. Warning2: An electrolytic capacitor installed with the wrong polarity might explode. 1. Servicing precautions are printed on the cabinet. Follow them. 2. Always unplug the unit's AC power cord from the AC power source before attempting to: (a) Remove or reinstall any component or assembly, (b) Disconnect an electrical plug or connector, (c) Connect a test component in parallel with an electrolytic capacitor. 3. Some components are raised above the printed circuit board for safety. An insulation tube or tape is sometimes used. The internal wiring is sometimes clamped to prevent contact with thermally hot components. Reinstall all such elements to their original position. 4. After servicing, always check that the screws, components and wiring have been correctly reinstalled. Make sure that the portion around the serviced part has not been damaged. 5. Check the insulation between the blades of the AC plug and accessible conductive parts (examples: metal panels, input terminals and earphone jacks). 6. Insulation Checking Procedure: Disconnect the power cord from the AC source and turn the power switch ON. Connect an insulation resistance meter (500V) to the blades of the AC plug. The insulation resistance between each blade of the AC plug and accessible conductive parts (see above) should be greater than 1 megohm. 7. Never defeat any of the B+ voltage interlocks. Do not apply AC power to the unit (or any of its assemblies) unless all solid-state heat sinks are correctly installed. 8. Always connect a test instrument's ground lead to the instrument chassis ground before connecting the positive lead; always remove the instrument's ground lead last.
Samsung Electronics
1-3
Precautions
1-3 Precautions for Electrostatically Sensitive Devices (ESDs)
1. Some semiconductor ("solid state") devices are easily damaged by static electricity. Such components are called Electrostatically Sensitive Devices (ESDs); examples include integrated circuits and some field-effect transistors. The following techniques will reduce the occurrence of component damage caused by static electricity. 2. Immediately before handling any semicon ductor components or assemblies, drain the electrostatic charge from your body by touching a known earth ground. Alternatively, wear a discharging wrist-strap device. (Be sure to remove it prior to applying power-- this is an electric shock precaution.) 3. After removing an ESD-equipped assembly, place it on a conductive surface such as aluminum foil to prevent accumulation of electrostatic charge. 4. Do not use freon-propelled chemicals. These can generate electrical charges that damage ESDs. 5. Use only a grounded-tip soldering iron when soldering or unsoldering ESDs. 6. Use only an anti-static solder removal device. Many solder removal devices are not rated as "anti-static"; these can accumulate sufficient electrical charge to damage ESDs. 7. Do not remove a replacement ESD from its protective package until you are ready to install it. Most replacement ESDs are packaged with leads that are electrically shorted together by conductive foam, aluminum foil or other conductive materials. 8. Immediately before removing the protective material from the leads of a replacement ESD, touch the protective material to the chassis or circuit assembly into which the device will be installed. 9. Minimize body motions when handling unpackaged replacement ESDs. Motions such as brushing clothes together, or lifting a foot from a carpeted floor can generate enough static electricity to damage an ESD.
1-4
Samsung Electronics
Reference Information
2. Reference Information
2-1 Tables of Abbreviations and Acronyms
Table 2-1 Abbreviations A Ah Å dB dBm °C °F °K F G GHz g H Hz h ips kWh kg kHz k km km/h kV kVA kW I MHz Ampere Ampere-hour Angstrom Decibel Decibel Referenced to One Milliwatt Degree Celsius Degree Fahrenheit degree Kelvin Farad Gauss Gigahertz Gram Henry Hertz Hour Inches Per Second Kilowatt-hour Kilogram Kilohertz Kilohm Kilometer Kilometer Per Hour Kilovolt Kilovolt-ampere Kilowatt Liter Megahertz MV MW M m µA µF µH µm µs µW mA mg mH mI mm ms mV nF pF Ib rpm rps s V VA W Wh Megavolt Megawatt Megohm Meter Microampere Microfarad Microhenry Micrometer Microsecond Microwatt Milliampere Milligram Millihenry Milliliter Millimeter Millisecond Millivolt Nanofarad Ohm Picofarad Pound Revolutions Per Minute Revolutions Per Second Second (Time) Volt Volt-ampere Watt Watt-hour
Samsung Electronics
2-1
Reference Information
Table 2-2 Table of Acronyms ABL AC ACC AF AFC AFT AGC AM ANSI APC APC A/V AVC BAL BPF B-Y CATV CB CCD CCTV Ch CRT CW DC DVM EIA ESD ESD FBP FBT FF FM FS GND G-Y H HF HI-FI IC IC IF Automatic Brightness Limiter Alternating Current Automatic Chroma Control Audio Frequency Automatic Frequency Control Automatic Fine Tuning Automatic Gain Control Amplitude Modulation American National Standards Institute Automatic Phase Control Automatic Picture Control Audio-Video Automatic Volume Control Balance Bandpass Filter Blue-Y Community Antenna Television (Cable TV) Citizens Band Charge Coupled Device Closed Circuit Television Channel Cathode Ray Tube Continuous Wave Direct Current Digital Volt Meter Electronics Industries Association Electrostatic Discharge Electrostatically Sensitive Device Feedback Pulse Flyback Transformer Flip-Flop Frequency Modulation Fail Safe Ground Green-Y High High-Frequency High Fidelity Inductance-Capacitance Integrated Circuit Intermediate Frequency I/O L L LED LF MOSFET MTS NAB NEC NTSC OSD PCB PLL PWM QIF R RC RF R-Y SAP SAW SIF SMPS S/N SW TP TTL TV UHF UL UV VCD VCO VCXO VHF VIF VR VTR VTVM TR Input/output Left Low Light Emitting Diode Low Frequency Metal-Oxide-Semiconductor-Field-Effect-Tr Multi-channel Television Sound National Association of Broadcasters National Electric Code National Television Systems Committee On Screen Display Printed Circuit Board Phase-Locked Loop Pulse Width Modulation Quadrature Intermediate Frequency Right Resistor & Capacitor Radio Frequency Red-Y Second Audio Program Surface Acoustic Wave(Filter) Sound Intermediate Frequency Switching Mode Power Supply Signal/Noise Switch Test Point Transistor Transistor Logic Television Ultra High Frequency Underwriters Laboratories Ultraviolet Variable-Capacitance Diode Voltage Controlled Oscillator Voltage Controlled Crystal Oscillator Very High Frequency Video Intermediate Frequency Variable Resistor Video Tape Recorder Vacuum Tube Voltmeter Transistor
2-2
Samsung Electronics
Reference Information
2-2 IC Line Up
Table 2 - 3 IC Line - Up NO BOARD LOC. NO IC201S IC601 IC901 IC902 IC602 HIC201 HIC202 HIC203 HIC204 HIC401 IC301 Q402 Q401 D414 IC401 1 MAIN Q404 IC801S D801S PC801S IC802 D805 D806 D807 D802 IC201 IC804 IC803 IC903 IC904 Q909 Q910 TU01S TU02S Samsung Electronics TCLN3181PA09A TCPN3081PD09A Main Tuner with IF Block Sub Tuner with IF Block Refer to Table 2-3-4 Refer to Table 2-3-5 2-3 FMG-G2CS KA78RM33 KA7806 KA78R08 KA78RM33 KIA7025AP 2N7000 3.3V Regulator 6V Regulator 8V Controlled Regulator 3.3V Regulator MICOM Reset IC IIC Level Shifter VDPY FML-G12S Rectifier Diode HC801 DDRI001 LA7845 KSC2073-H2 KSD5703 FMP-3FU KA393 IRF620 3S1265R RBV606 PC123Y KA78R05 SPS Controllor Bridge Diode Photo Coupler 5V Controlled Regulator E/W Drive IC Horizontal Drive IC HC401 100Hz Horizontal Pulse AMP Vertical IC Option DRGB001 RGB Drive AMP Hybrid IC SPEC VDP3130Y MSP3451G SIM408AY KS24L161 TDA7297 DESCRIPTION Video Processor Multistandard Sound Processor MICOM, TTX(MTP) EEPROM Audio AMP Refer to Table 2-3-3 VM Option REMARK Refer to Table 2-3-1 Refer to Table 2-3-2
Reference Information
Table 2 - 3 IC Line - Up NO BOARD LOC. NO IC501 IC502 IC503 2 CRT QF04 QF05 QG02 QG03 ICG01 3 4 5 DOUBLE FOCUS V-S/W PIP ICH01 QH01 ICS01 ICP01 ICP02 2SC2344 2SA1011 KSA940 KSD2073-H2 KA4558 KA4558 2SC4636RB TEA6425 SDA9388X EZ1086CM OP-AMP (TILT) OP-AMP TR-Power Video Switching IC with Adder Output High-end Picture-In Picture IC 3.3V Regulator Option Option Option Push-Pull (VM) Option TR-Power (TILT) TDA6111Q Video Output AMP R.G.B Drive SPEC DESCRIPTION REMARK
2-4
Samsung Electronics
Reference Information
Table 2-3-1 VIDEO IC (IC201S) SPEC VDP3108B VDP3112B VDP3120B VDP3130Y VDP3140D 50Hz Basic 50Hz, 2H Comb Filtr 50Hz, 2H Comb Filter, Horizontal Scaler 50Hz, 2H Comb Filter, DVD Input 100Hz FUNCTION REMARK
Table 2-3-2 SOUND IC (IC601) SPEC MSP3400D MSP3410D MSP3411G MSP3440G MSP3451G Multistandard, A2 Stereo Multistandard, A2 Stereo, Nicam Multistandard, A2 Stereo, Vitual Dolby Multistandard, A2 Stereo, Vitual Dolby Multistandard, A2 Stereo, Vitual Dolby FUNCTION REMARK
Table 2-3-3 SOUND AMP (IC602) SPEC TDA7297 15W x 2CH, 10W x 2CH FUNCTION REMARK
Table 2-3-4 1'st TUNER (TU01S) SPEC TCLN3181PA09A TCPN3081PC09A TCPN3081PA09A Note FUNCTION NTSC, PAL N.M, LNA Function PAL N.M, NTSC, LNA Function PAL N.M, NTSC, LNA Function REMARK Main, F-Jack Main, Thin Jack Main 1Tuner
TCPS3001PD09A(S) is out-of-date, TCPS3001PD09D(S) which is up-to-date has the same function.
Table 2-3-5 2'nd TUNER (TU02S) SPEC TCLN3181PD09A TCPN3081PD09A FUNCTION NTSC, PAL N.M LNA Function NTSC Sub Sub REMARK
Samsung Electronics
2-5
MEMO
2-6
Samsung Electronics
Specifications
3. Specifications
Television System
Multi NTSC-M, PAL N.M 75ohms, Coaxial Cable 160W (Applied When 29" Flat) Free Volts(100V-240Volts) Free Voltage Frequency 50/60Hz 15W x 2CH Output 10W x 2CH 5W x 2CH Vitual Dolby Effect Turbo Sound Pseudo Stereo RCA Input Front (AV2) S-VHS Head-Phone
Option Option Not Present R815
Antena Input
Consumption
Power
Requirements
Sound
Jacks
Back
2 AV Input DVD Input(YPbPr) AV2 Monitor Audio Output S-VHS
Option Option Option
Specifications are subject to change.
Specifications for Model Name Function P 2 TUNER PIP NOTE
Samsung Electronics
3-1
MEMO
3-2
Samsung Electronics
Alignment and Adjustments
4. Alignment and Adjustments
4-1 General Alignment Instructions
1. Usually, a color TV-VCR needs only slight touch-up adjustment upon installation. Check the basic characteristics such as height, horizontal and vertical sync and focus. 2. Observe the picture for good black and white details. There should be objectionable color shading; if color shading is present, demagnetize, perform purity and convergence adjustments described below. 3. Use the specified test equipment or its equivalent. 4. Correct impedance matching is essential. 8. To protect against shock hazard, use an isolation transformer. 5. Avoid overload. Excessive signal from a sweep generator might overload the front-end of the TV. When inserting signal markers, do not allow the marker generator to distort test results. 6. Connect the TV only to an AC power source with voltage and frequency as specified on the backcover nameplate. 7. Do not attempt to connect or disconnect any wires while the TV is turned on. Make sure that the power cord is disconnected before replacing any parts.
4-2 Automatic Degaussing
A degaussing coil is mounted around the picture tube, so that external degaussing after moving the TV should be unnecessary. But the receiver must be properly degaussed upon installation. The degaussing coil operates for about 1 second after the power is switched ON. If the set is moved or turned in a different direction, the power should be OFF for at least 10 minutes. If the chassis or parts of the cabinet become magnetized, poor color purity will result. If this happens, use an external degaussing coil. Slowly move the degaussing coil around the faceplate of the picture tube and the sides and front of the receiver. Slowly withdraw the coil to a distance of about 6 feet before turning power OFF. If color shading persists, perform the following Color purity and Convergence adjustments.
4-3 High voltage Check
CAUTION : There is no high voltage adjustment on this chassis. The B+ power supply should be +135 volts (with full color- bar input and normal picture level).
1. Connect a digital voltmeter to the second anode of the picture tube. 2. Turn on the TV. Set the Brightness and Contrast controls to minimum (zero beam current). 3. Adjust the Brightness and contrast controls to both extremes. Ensure that the high voltage does not exceed 32 KV under any conditions.
Samsung Electronics
4-1
Alignment and Adjustments
4-4 Dynamic Focus Adjustment
1. A dynamic focus adjustment should be done after replacing the CRT PCB, FBT or CRT. 2. Input a crosshatch pattern.
3. Enter " STANDARD " in video mode. 4. Turn the Dynamic focus VR fully clockwise (maximum).( ) 5. Turn the Static focus VR fully counterclockwise (maximum).( ) 6. Slowly turn the static focus VR counterclockwise. Adjust until the vertical line in the middle of the screen has maximum clarity.( ) 7. Slowly turn the dynamic focus VR (clockwise) and adjust the 3rd horizontal line for maximum clarity.( ) 8. Repeat 4-7, if necessary.
H
STATIC FOCUS VR
V
DYNAMIC FOCUS VR
SCREEN
4-5 SCREEN Adjustment
1. Input Toshiba Pattern 2. Enter "Service Mode".(Refer to "Service Mode") 3. Select "G2-Adjust". 4. Set the values as below. IBRM = 200 WDRV = 35 CDL = 200 COLR G B = 120 120 120
4-2
Samsung Electronics
Alignment and Adjustments
5. Turn the SCREEN VR until "MRCR G B" and "MRWDG" are green and those value are about 100. (The incorrect SCREEN Voltage may result that "MRCR G B" and "MRWDG" should be red)
Note 1. When you do not have Toshiba Pattern, follow this method. 1. 2. 3. 4. 5. Set the TV on the condition that AV mode no signal(black) Enter the "Menu" and set the mode to blue screen off. Enter the "Service Mode". Select " G2-Adjust". Set the values as below. IBRM = 200 WDRV = 35 CDL = 200 COLR G B = 120 120 120 6. Turn the SCREEN VR until the value of " MRCR G B" is about 120. Do not mind that the "OSD" Color is red.
s After completing G2-Adjust, follow this procedure. x Enter the "Video Adjust 1". Choose any item in menu. (ex. Select "Red Cutoff") Change the value of item you select, and recover the value.
For example, when the value of "Red Cutoff" is 127, change the value to 128 and restore the value to 127. If you do not follow this procedure, the picture may be abnormal. For example, when the TV set is on, the picture becames brighter gradually.
Samsung Electronics
4-3
Alignment and Adjustments
4-6 E2PROM (IC902) Replacement
1. When IC902 is replaced, all adjustment data revert to the initial values. So, all adjustment values when servicing should be readjusted. 2. After IC902 is replaced, connect the AC power supply cord. 3. Turn the power switch ON. 4. In stand-by, warm up the TV for at least 10 seconds. 5. Power on the TV.
4-7 White Balance Adjustment
s Equipment : Color-Analyzer (CA-100) s Input Signal : Pattern signal (Toshiba pattern) 1. Select STANDARD from the menu. 2. Input an 100% White pattern. 3. Enter the "Service Mode". (Refer to "4-8 Service Mode") 4. Warm up the TV set at least for 30 minutes. 5. Input a Toshiba pattern signal. 6. Enter the "Video Adjust1". - Adjust "Sub Contrast" so that Y (luminance) becomes 50 ft ± 3. - Use "Red Drive" and " Blue Drive" to adjust High-Light (x : 275, y : 295) - Adjust "Sub Bright" so that Y (luminance) becomes 1.5ft ± 0.3. - Use "Red Cutoff" and "Blue Cutoff" to adjust Low-Light (x : 275, y : 295). 7. Adjust CA-100 so that the final adjustment value can be fixed. 8. Use the Channel Up/Down (v/w) buttons to move the cursor on the adjustment modes. 9. Use the Volume +/- buttons to change the adjustment value.
4-4
Samsung Electronics
Alignment and Adjustments
4-8 Factory Adjustment
4-8-1 Service Mode
1. To enter the "Service Mode", Press the remote-control keys in this sequence : - If you do not have Factory remote-control
PICTURE OFF MUTE Keys Number 1,8,2 PICTURE ON
- If you have Factory remote-control
PICTURE ON DISPLAY ( ) FACTORY
2. After the Service Mode is entered, the initial screen is as shown in the figure below.
Service Deflection Video Adjust 1 Video Adjust 2 Video Adjust 3 Option Reset G2-Adjust Others VDP Verision : Y
*
These hexa * depends on digits are check sum value which the MICOM. If check sum value is changed, the value of 2 E PROM Data newly initialed.
3. Use the Channel Up/Down buttons to move the cursor in the adjustment parameters. Note 2. - When CRT, CRT PCB, FBT, E PROM (sometimes MICOM) is replaced, the adjustment values should be controlled. - After the Service adjustment is completed, Do not select "Reset" in the service mode menu. (After above procedure is done, power is on initially and the "Plug and Play" will be operated.)
2
Note 3. - When E PROM (IC902) and Micom are replaced at the same time : 1. After the Factory Mode is entered, check the VDP version in the service list. 2. Set the version so that the VDP version is identical with the video chip (IC201S) 3. After all settings are completed, adjust the service value of each mode to its default. 4. Refer to "Service Manual" for factory value. 5. Check the version a. Check the VDP version "Y" in the Factory Mode. b. Version Mode : "Y", "B" from IC201S(Video Chip) VDD3130"Y" VDD3112"B", VDD3108"B"
2
Samsung Electronics
4-5
Alignment and Adjustments
4-8-2 Memory Data
4-8-2(A) DEFLECTION (GEOMETRIC ADJUSTMENT VALUE)
DEFLECTION H Bow H Angle H DSCC V SHIFT V AMP V SLOPE V SC H EW H TRAPEZIUM H PARABOLA H SYMMETRY H CORNER H SHIFT PIP CONTRAST PIP TINT PIP PAL V.POS PIP NTSC V.POS PIP H.POS
Initial Value 0 0 1 -40 5 -2 -7 64 -20 -13 13 15 4 15 0 12 10 15
Adjustment Value Fixed Adjustment Fixed Adjustment Adjustment Adjustment Fixed Adjustment Adjustment Adjustment Fixed Adjustment Fixed Fixed Fixed Fixed Fixed
SAM2540 SAM2740 0 0 1 -18 18 -4 -13 24 20 17 13 69 13 -
TXK3276 0 0 1 -27 -17 -3 -13 71 -50 10 13 -13 20 -
CL29A6 0 10 3 -55 0 0 -17 45 -50 -5 13 25 -20 15 0 12 10 15
TXK3279 0 0 3 -51 -35 -2 0 49 -30 18 13 -34 -6 10 0 12 10 15
TXK3676 0 0 1 -27 -17 -3 -13 71 -50 10 13 -13 20 -
TXK3679 0 0 3 -51 -35 -2 0 49 -30 18 13 -34 -6 10 0 12 10 15
4-6
Samsung Electronics
Alignment and Adjustments
4-8-2(B) SCREEN CHANGE (I2C BUS GEOMETRIC ADJUSTMENT)
1
V Shift
6
V Amp
2
V Slope
7
V SC
3
H EW
8
H Trapizium
4
H Parabola
9
H Symmetry
5
H Corner
10
H Shift
Samsung Electronics
4-7
Alignment and Adjustments
4-8-2(C) VIDEO ADJUST 1
VIDEO ADJUST1 RED CUT OFF GREEN CUT OFF BLUE CUT OFF RED DRIVE GREEN DRIVE BLUE DRIVE SUB BRIGHT SUB CONTRAST SUB COLOR SUB TINT BCL THRESHOLD BCLGAIN BCL TIME DVD SUBTint N. YC DELAY
Initial Value 127 127 127 127 127 127 110 52 27 30 62 8 13 0
Adjustment Value Adjustment Fixed Adjustment Adjustment Fixed Adjustment Adjustment Adjustment Fixed Fixed Fixed Fixed Fixed Fixed
SAM2540 SAM2740 127 127 127 127 127 127 100 52 50 70 58 8 10 3
TXK3276 127 127 127 127 127 127 100 52 50 70 58 8 10 3
CL29A6 127 127 127 127 127 127 100 52 50 40 65 8 6 25 3
TXK3279 127 127 127 127 127 127 100 52 50 70 60 9 5 25 3
TXK3676 127 127 127 127 127 127 100 52 50 70 58 8 10 3
TXK3679 127 127 127 127 127 127 100 52 50 70 60 9 5 25 3
Note 3. Beam Control Limit Characteristic
beam
MIN 1.8mA 1.6mA BCL THESHOLD BCL GAIN MAX
Table 1. YC Delay Adjustment Table N.YC Delay Value NTSC Def. 4 M 3
The "Def." means that TV is in AV mode.
WDRGB
50
IRE
4-8
Samsung Electronics
Alignment and Adjustments
4-8-2(D) VIDEO 2 ADJUST
VIDEO ADJUST2 B STRETCH-BTHR B DTRETCH-BTLT B STERTCH-BAM CORING NTSC COMB FILTER RGB BRIGHT RG B CONTRAST EHT TIME EHT COMPENSATION DTI CORING DTI GAIN DTI BAND EHT Offset EHT Horizontal
Initial Value 50 8 4 31 1 0 0 0 60
Adjustment Value Fixed Fixed Fixed Fixed Fixed Fixed Fixed Fixed Fixed Fixed Fixed Fixed Fixed
SAM2540 SAM2740 50 8 4 31 1 0 0 0 60 0 1 1 -
TXK3276 50 8 4 31 1 45 15 0 60 0 1 1 -
CL29A6 50 8 4 31 3 0 0 3 60 0 1 1 0 0
TXK3279 50 8 4 31 3 45 15 8 60 0 1 1 0 0
TXK3676 50 8 4 31 1 45 15 0 60 0 1 1 -
TXK3679 50 8 4 31 3 45 15 8 60 0 1 1 0 0
0 0
Coring : The Value of Center Frequency for the active bandwidth.
4-8-2(E) VIDEO 3 ADJUST
VIDEO ADJUST3 PEAK Threshold SOFT LIMIT SLOPE B HARD LIMIT MODULATION ON/OFF A TILT POINT B TILT POINT GAIN 1 (VIDEO) DELAY 1 (VIDEO) PEAK VIDEO REF PEAK VIDEO GAIN LIMIT VALUE VELOCITY DELAY VELOCITY CORING ACC-REF ACCR
Initial Value 255 4 255 0 0 0
Adjustment Value Fixed Fixed Fixed Fixed Fixed Fixed Fixed Fixed Fixed Fixed Fixed Fixed Fixed Fixed Fixed
SAM2540 SAM2740 255 4 255 0 0 114 11 3 0 0 74 7 10 20 21
TXK3276 255 4 255 0 0 114 31 3 0 0 74 7 10 20 21
CL29A6 255 4 255 0 0 114 31 3 0 0 127 7 2 20 21
TXK3279 255 4 255 0 0 114 31 3 0 0 74 7 10 20 21
TXK3676 255 4 255 0 0 114 31 3 0 0 74 7 10 20 21
TXK3679 255 4 255 0 0 114 31 3 0 0 74 7 10 20 21
20 21
Samsung Electronics
4-9
Alignment and Adjustments
Note 5. Soft Limit & Hard Limit
Output 511
Part 1
Part 2
Slope 1 [0...15]
Hard limiter
0 2 4 6 8 10 12 14
Slope 2 [0...15]
400
300
200
0 2 4 6 8 10 12 14
Soft Limit Slope B
range=256...511
"Soft Limit" is that Limitting the peak white without feed-back, but "Peak Limit" is that with feed-back for white peak level
100 tilt 1 [0...511] 0 0 100 200 300 400 500 600 700 800 900 tilt 2 [0...511] Li 1023
4-8-2(F) OPTION
Model No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 Description SYSTEM ACS(CT, CTA) SOUND CRT AV MODE(V,Y) AUDIO MUTE X-RAY VIDEO-MUTE TILT CONTROL GAME+DEMO(CN) LNA PIP VCHIP(CT,CTA) BLUE SCREEN AKB AUTO POWER ON HOTEL Option Byte Note 6. V-DOLBY MSP3451G, MSP3440GB6 CL29A6 Initial Value CN(EN+SP+PO) OFF VIRTUAL DOLBY 4:3 2RCA + S + D ON OFF ON ON ON ON 2-TUNER OFF ON ON OFF OFF 04 DE 12 1C SAM2540 SAM2740 Initial Value CT(EN+SP+FR) ON STEREO 4:3 1RCA ON ON OFF OFF OFF OFF OFF ON OFF OFF OFF 01 01 80 09 TXK3276 TXK3676 Initial Value CT(EN+SP+FR) ON STEREO 4:3 2RCA +S ON ON OFF OFF OFF OFF OFF ON OFF OFF OFF 01 01 88 09 TXK3279 TXK3679 Initial Value CT(EN+SP+FR) ON VIRTUAL DOLBY 4:3 2RCA +S+D ON ON OFF OFF OFF OFF 2-TUNER ON OFF OFF OFF 04 01 92 09 TXK3279 TXK3679 Initial Value CT(EN+SP+FR) OFF VIRTUAL DOLBY 4:3 2RCA +S+D ON ON ON ON OFF ON 2-TUNER OFF ON ON OFF OFF
4-10
Samsung Electronics
Alignment and Adjustments
4-8-2(G) OTHERS
OTHERS VSU VSU2 H QEW H ZOOM Parabola H 16:9 Parabola DVD Tint Control PAL V SHIFT PAL H SHIFT Melidy Volume PIP BRIGHT PIP COLOR
Initial Value 108 0 8 -10 0
Adjustment Value Fixed Fixed Fixed Fixed Fixed Fixed Fixed Fixed Fixed Fixed
SAM2540 SAM2740 105 0 0 8 -18 0 -29 18 7
TXK3276 105 0 0 8 -18 0 -29 18 7
CL29A6 98 0 0 12 -19 1 -66 -15 7 3 7
TXK3279 108 0 0 12 -19 1 -62 -1 7 5 7
TXK3676 105 0 0 0 0 0 -29 18 7
TXK3679 108 0 0 0 0 0 -20 -3 7 5 7
5
4-8-2(G) G2 ADJUST
Initial Value Adjustment Value SAM2540 SAM2740
G2 Adjust MRC R G B MRWDG IBRM WDRV CDL COL VDP Version
TXK3276
CL29A6
TXK3279
TXK3676
TXK3679
-10 0
FIX FIX FIX FIX
200 35 150 130 B
195 35 170 130 B
200 35 200 120 Y
195 35 170 130 Y
195 35 170 130 B
195 35 170 130 Y
WHITE BALANCE
H L
275,295,35 275,295,1.2
275,295,28 275,295,50 275,295,28 275,295,28 275,295,28 275,295,1.0 275,295,1.5 275,295,1.0 275,295,1.0 275,295,1.0
Samsung Electronics
4-11
Alignment and Adjustments
4-9 MICOM
4-9-1 Pin Layout
Write Protect EEPROM SDA EEPROM SCL Bus-Stop Main SDA Main SCL Sound Reset Video Reset VDD 2.5V GND VDD 3.3V CVBS Input VDD 2.5V GND AFT AV1 Ident AV2 Ident Key 1 H-Sync V-Sync Key 3 Key 2 X-Ray Protect IR Input Stand-By LED Time LED
1 2 3 4 5 6 7 8 9 10 11 12 13 14
I/O I/O IO I/O I/O I/O I/O I/O
PWM I/O I/O
52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28
15 ADC 16 ADC 17 ADC 18 ADC 19 20 21 I/O 22 I/O 23 I/O 24 I/O 25 I/O 26 I/O
S I M 4 0 8 A Y
I/O
27
Tilt N.C. Power Sound Mute N.C. N.C. PX. Y PX. Y VDD 3.3V GND VDD 2.5V CORE OSD-B OSD-G OSD-R VDD 2.5V GND X-TAL Out X-TAL In MICOM Reset N.C. N.C. VDD 3.3V GND N.C. Relay
4-12
Samsung Electronics
Alignment and Adjustments
4-9-2 Pin Assignment Specification
PIN NO FUNCTION 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 I/O I/O I/O I/O I/O I/O I/O I/O Vdd GND Vdd CVBS Vdd GND ADC ADC ADC ADC HS VS I/O I/O I/O I/O I/O I/O
ASSIGN Write Protect ROM SDA ROM SCL Bus Stop Main SDA Main SCL Sound Reset Video Reset VDD 2.5V
IN/OUT Out I/O I/O In I/O I/O Out Out
ACTIVE H/L Low
DESCRIPTION EEPROM Write Protection EEPROM Serial Data Line EEPROM Serial Clock Line
Low
Disable Micom IIC Peripheral IC Serial Data Line
Low Low
Peripheral IC Serial Clock Line MSP IC Initial Control VDP IC Initial Control
VDD 3.3V CVBS Input VDD 2.5V In TTX CVBS Input Analog B+ Analog Ground AFT AV1-ID AV2-ID Key1 H-Sync V-Sync Key3 Key2 X-Ray IR-In STD-LED TIM-LED In In In In In In In In In In Out Out Auto Fine Tuning Control AV1 Ident AV2 Ident Key1 Input Horizontal Sync Input Vertical Sync Input Key3 Input Key2 Input X-Ray Protection Remocon Signal Input LED Drive Output(Red) LED Drive Output(Green)
Samsung Electronics
4-13
Alignment and Adjustments
4-9-2 Pin Assignment Specification (Continued)
PIN NO FUNCTION 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 I/O N.C. GND Vdd N.C. N.C. Reset X-In X-Out GND Vdd R G B COR Vdd GND Vdd I/O I/O N.C. Not Used (Programmed Gound Level) N.C. I/O I/O N.C. I/O Tilt Out PWM S-Mute Power Out Out High Low Sound Amp Mute Picture On/Off Control Not Used (Programmed Gound Level) Tilt Control Output VDD 3.3V PX.Y PX.Y In When The Caption Function Adopted, Used. Out VDD 2.5V OSD-R OSD-G OSD-B CORE VDD 2.5V Out Out Out Out Reset X-TAL In X-TAL Out In In Out Low 6MHz 6MHz VDD 3.3V ASSIGN Relay
IN/OUT Out
ACTIVE H/L Low
DESCRIPTION Activate Degausssing Coil Not Used (Programmed Gound Level) Analog Ground Not Used (Programmed Gound Level) Not Used (Programmed Gound Level) Micom Hardware Reset Crystal Oscillation Input Crystal Oscillation Output Analog Ground Analog B+ OSD/Caption Output (Red) OSD/Caption Output (Green) OSD/Caption Output (Blue) Fast Blank/Half Contrast Output
4-14
Samsung Electronics
Plug in Power Cord
Samsung Electronics
ON Check LED lamp OFF Normal Normal Check and Replace the MICOM Normal Check and Replace IC903 Check IC901 MICOM Input Voltage Abnormal Normal Abnormal Check the MICOM Power #59 With Remote Controller Replace the MICOM Abnormal Replace Q908 Normal Normal Check IC802, IC803 Replace IC802, IC803 Normal Check IC201S VDP H-OUT #50 Abnormal Replace IC201S Normal Check Q401 H-TR Replace Q401 Normal Check 135V Line Check PC801S, IC801S Normal Replace FBT Abnormal Abnormal Check R828 and D805 Abnormal Check IC801S and FP801S Normal Check and Replace R828 or D805 Abnormal Check IC804 Input Voltage Abnormal Normal Check and Replace IC804 Check D801 and D811 Abnormal Abnormal Replace D801 or D811 Check IC903 3.3V Regulator Input Voltage Normal Replace Q908
5-1 No Power
5. Troubleshooting
Abnormal
Check MICOM IIC #5, #6
Check Level Shifter Q909, Q910 Output(If 2N7000 Output has the DC Component over 0.7V, it is broken)
Normal
Abnormal
Check MICOM IIC #2, #3
Abnormal
Replace Q909, Q910
Normal
Check IC902 EEPROM
Replace EEPROM(IC902)
Normal
Check IC201S
Note : When you check whether any component is normal, you must let the output pin be open in order not to be affected by the side of output.
Troubleshooting
5-1
No Picture, but sound is in normal operation
Normal
Turn the VR of FBT, higher screen voltage and Check the Deflection is in Normal Operation (If the deflection is in operation, flyback signal is appeared)
Abnormal
Normal
Check CRT PCB RK, BK, GK
Abnormal
Normal
Check IC201S #31
Abnormal
Check Heater Voltage Abnormal Normal Check CRT and FBT
Check HIC202, HIC203, HIC204 Output
Abnormal
Check 8V Check IC201S #63 or #59 Normal Abnormal Normal Normal
Abnormal
Check DZ202
Abnormal
Check CRT and FBT
Normal
Check IC803 Replace IC201S Check 200V, 16.5V Line Check Tuner CVBS Output Check IC301
Replace DZ202
Replace IC201S
5-2 No Picture
Troubleshooting
5-2
Samsung Electronics
Troubleshooting
5-3 No Sound
No Sound, but Picture is in normal operation
Normal
Check the CN602 Connection and Signal
Abnormal
Check the Speaker Wire Connection
Normal
Check 14V Line
Abnormal
Check IC602 #7 (If the pin is in low state, Sound is mute) Normal
Abnormal
Check FA803S
Check D816, Q906 Check IC601 #24, #25 Normal Replace IC602 Check IC601 Input Voltages (5V,8V) Normal Check the coils around IC601 Check IC601 Input Signal Normal Replace IC601 Check the Tuner Abnormal Abnormal Abnormal
Samsung Electronics
5-3
MEMO
5-4
Samsung Electronics
Exploded View & Parts List
6. Exploded View & Parts List
6-1 TXM2790FX/XAA
No 1 1-1 1-2 1-3 1-4 1-5 1-6 1-7 1-8 1-9 1-10 1-11 1-12 1-13 Code No AA64-02959A AA64-70117B AA64-02544A AA61-60003J AA61-40113A 6006-001095 AA96-00960A AA64-02546A 6003-001019 AA64-02548A 6003-001019 AA65-30105A 3001-000274 6003-001026 Description;Specification CABINET-FRONT;29K7,HIPS,VO,BLK,DG703P,SE BADGE-BRAND;AL,SS,R2000,25,SILVER CT-633 KNOB-POWER;29K7,ABS,HB,G3676 SPRING-CS;-,-,SUS304,0.5,OD6,H STOPPER-PCB;-,ABS,HB,NTR. SCREW-ASS'Y TAPT;WP,BH,+,M4,L12,ZPC(YEL) ASSY-PCB;A/V FRONT;KS3A,29 KNOB-CONTROL;29K7,ABS,HB,G3676 SCREW-TAPTITE;RH,+,B,M4,L12,ZPC(BLK),SWR WINDOW-RMC,LED;29K7,PC,CLR SCREW-TAPTITE;RH,+,B,M4,L12,ZPC(BLK),SWR CLAMP-WIRE;NYLON 66N,VO,NTR,15MM SPEAKER-GENERAL;5W8OHM100X50MM SCREW-TAPTITE;RH,+,B,M4,L15,ZPC(BLK),SWR Q'ty 1 1 1 1 1 2 1 1 1 1 1 1 2 8 Remark F/C BADGE KP SPRING STOPPE AV+CF A/A-V KC KC+CF WR WR+CF CWFCL SPK SPK+CF
2 2-1 2-2
AA03-00360A AA65-30113A AA60-10050V
CRT COLOR;A68QCP891X100(M),+380MG,1.11MH CLAMP-D,COIL;NYLON66,V2,BLK,TVI25~29,SCREW-ASSY;WC,HH,+,M6,L30,SWRCH18A,ZPC(S
1 4 4
CRT CDCOIL CRT+CF
3 3-1 3-2
AA64-02543A 6003-001026 AA96-00695A
CABINET-BACK,29K7,HIPS,VO,BLK SCREW-TAPTITE;RH,+,B,M4,L15,ZPC(BLK),SWR ASSY-POWER,CORD;EP2/YES,H/C450,ME301P
1 7 1
B/C CB+CF PWR/AC
Samsung Electronics
6-1
Electrical Parts List
7. Electrical Parts List
7-1 TXM2790FX/XAA
Loc. No. Code No. Description ; Specification Remark Loc. No. Code No. Description ; Specification Remark
ASSY-CHASSIS
1 A/CHAS 2 2 2 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 4 4 4 4 3 4 4 4 4 4 4 3 4 4 CW FBT A/MAIN Q402 Q404 PC801S IC902 IC401 IC803 IC903 IC601 IC201S PT801S NT802S R807 CY802S C423 C407 C426 CX801S CX802S C405 C406 C803 C820 C815 SW906 RL801S FP801S CN501 CN602 CN502 CN702 JA701 JA702 IC901 T801S T444S T401 L402 L405 L808 L403 L408 LX801S LX802S GT101 TU01S RM901 L/PQS IC804 AA91-04214L AA65-30018A AA65-30018A AA94-08533D 0502-001007 0505-000156 0604-001038 1103-001177 1202-000103 1203-001697 1203-001944 1204-001737 1204-001812 1404-000002 1404-001045 2006-001083 2201-000446 2301-001192 2301-001338 2306-000204 2306-000318 2306-000318 2306-000330 2306-000330 2401-001652 2401-003076 2401-003602 3404-001004 3501-001040 3601-000293 3711-002641 3711-002644 3711-002646 3711-002647 3722-001333 3722-001596 AA09-00243A AA26-00044C AA26-00105A AA26-50001L AA27-00067A AA27-00096A AA27-00098A AA27-00099A AA27-00103A AA29-00012A AA29-00012A AA39-20010B AA40-00074A AA59-60001U AA68-01018A AA96-00243C 0205-000129 1203-000284 6003-000335 AA62-00045A AA96-00275A 0205-000129 0402-001296 0502-001136 6003-000335 AA60-30001A AA62-00051A AA96-00276C 0205-000129 0402-001399 ASSY-CHASSIS;KS3A;SPACE,27,SEA/SECA CLAMP-WIRE;-,NYLON6.6,-,-,DATL CLAMP-WIRE;-,NYLON6.6,-,-,DATL ASSY-PCB MAIN;KS3A,27,SEA/SECA TR-POWER;KSC2073-H2,NPN,150V,1 FET-SILICON;IRF620,N,200V,5A,0.8ohm,50W, PHOTOCOUPLER;TR,130-260%,200MW IC-EEPROM24WC16,2048x8bit,DIP,8P,2.5V IC-VOLTAGECOMP.393,DIP,8P,300MIL,DUAL, IC-VOLTAGEREGULATOR78R08,TO-220,4P,P IC-POSI.FIXEDREG.78RM33,TO-220,3P,PLAST IC-SOUND PROCESSOR;MSP3451G-PO-A2,DIP,52 IC-VIDEO PROCESS;VDP3130Y-B2,DIP,64P,760 THERMISTOR;NTC,90HM,20%,TR,AC290VRMS,120 THERMISTOR NTC;4.7OHM,15%,2900K,35.0MW,T R-CEMENT;120ohm,5%,5W,CJ,TP,14x10x27mm C-CERAMIC,AC;CK45PE400V332-M(T C-FILM,MPPF;820nF,5%,400V,TP,29x18.5x25. C-FILM,MPE,PPF0.68nF,5%,1.6kV,TP,28x7x1 C-FILM,MPPF;430NF,5%,400V,-,20 C-FILM,MPPF;220NF,20%,250V,-,2 C-FILM,MPPF;220NF,20%,250V,-,2 C-FILM;CF922P1.6KVT772-HBUP C-FILM;CF922P1.6KVT772-HBUP C-ELECTROLYTIC;CE04W250V680M-M C-AL;3300uF,20%,50V,WP,BK,18x35.5mm C-AL;220uF,20%,160V,GP,BK,22x25mm,1 SWITCH TACT;12V,50MA,160GF8.4X22.7MM RELAYPOWER;12VDC,500MW,10A,1FO FUSE-CARTRIDGE;250V,5A,SLOW-BLOW,GLASS,5 POST-HEADER;67094-010(AUTO) POST-HEADER;67094-005(AUTO) POST-HEADER;67094-007(AUTO) POST-HEADER;67094-008(AUTO) JACK-RCA9P,3.2mm,NI,BLK JACK-RCA;3P/9P,3.5mm,NI,BLK(GRN/BLU/RED IC MICOM;SIM-408A3,CL-21A8,52P,-0.3~+7, TRANS SWITCHING,CODE-NO,CT-21A8,AC90-260 TRANS FBT;FUH-29C001(S),CT29A5P,4.3MH,13 HORIZ.DRIVE;-,29MH,133UH,4.5UH COIL HORIZ. WIDTH;-,240uH,YL9N 12x20 C:6 COIL HORIZ. WIDTH;-,10.0mH,DR15 X 27.5,U COIL CHOKE;-,-,24uH,10%,-,0.1,3.0A,DR10X COIL LINEARITY;23.5uH,23.5uH,DR14x15C:5. COIL CHOKE;600UH,-,600UH,+-10%,600UH,0.5 FILTER LINE NOISE;CS29A6PF8X/HAC,-,0.1MA FILTER LINE NOISE;CS29A6PF8X/HAC,-,0.1MA LEAD-CONNECTOR,ASSY;-,YFH800-01,500MM,1P TUNER;TCPN3081PA09A(B),NTSC,181CH,45 MODULE-REMOCON;-,ORC-50VF,38KH LABEL-PQS,-,50mmX,13,-,WHITE,ASSY H/S;-,REGULATOR,AA62-00045A,KA7806 GREASE-SILICON;SC102,JAPAN IC-POSI.FIXEDREG.;7806,TO-220, SCREW-TAPTITE;RH,+,2S,M3,L8,ZPC(YEL),SWR HEAT SINK-PS;-,-,T1.0,-,-,DREAM,-,-,-,-, ASSY H/S;-,COMPLEX,AA62-00051A,KSD5703, GREASE-SILICON;SC102,JAPAN DIODE-RECTIFIER;FMP-3FU,1500V,5A,T0-3PF TR-POWER;KSD5703,NPN,70W,TO-3PF,ST,8SCREW-TAPTITE;RH,+,2S,M3,L8,ZPC(YEL),SWR WASHER-PLATE;-,M3,ID3.5,15X8.5,T1.0,-,SB HEAT SINK-PS;-,-,-,SILVER,HOLE 31mm,ALL, ASSY H/S;-,BRIDGE ,AA62-00052A,GSIB660, GREASE-SILICON;SC102,JAPAN DIODE-BRIDGE;GSIB660,600V,6A,SIP-4,BK
! ! !
!
! ! ! !
!
! !
! !
! ! !
!
! ! !
!
! ! !
!
! ! !
HC401
!
D801S
4 4 4 3 3 4 4 4 4 4 4 3 4 4 3 4 4 4 4 3 4 4 4 4 4 4 3 4 4 4 3 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4
LD901 HC801
PWR/AC
IC602
IC801S
IC301
A/AUTO D201 D202 D207 D208 D209 D210 D211 D602 D604 D804 D906 DZ402 D405 D408 D402 DR01S D413 D401 D404 D301 D411 D803 D816 D801 D403 D406 D407 D808 D810 D811 D907 DZ201 DZ202 DZ204 DZ205 DZ601 DZ603 DZ605
6003-000335 AA60-30003A AA62-00052A AA96-00461A AA96-00475A 0205-000129 0402-000233 0402-001230 1203-001006 6003-000334 AA62-00066B AA96-00695A AA39-10007Y AA61-20284A AA96-50372B 0205-000129 1201-001308 6003-000333 AA62-30181J AA96-50371F 0205-000129 6003-000333 AA02-00007A AA13-00101A AA61-10386A AA62-30181H AA96-50406A 1204-000517 6003-000333 AA62-30180K AA97-07506P 0401-000005 0401-000005 0401-000005 0401-000005 0401-000005 0401-000005 0401-000005 0401-000005 0401-000005 0401-000005 0401-000005 0401-000005 0402-000493 0402-000493 0402-000534 0402-000534 0402-000537 0402-000540 0402-000540 0402-000546 0402-000546 0402-000546 0402-000546 0402-001111 0402-000132 0402-000132 0402-000132 0402-000132 0402-000132 0402-000132 0402-000132 0403-000508 0403-000508 0403-000508 0403-000508 0403-000508 0403-000508 0403-000508
SCREW-TAPTITE;RH,+,2S,M3,L8,ZPC(YEL),SWR WASHER;-,-,-,-,T1.5,-,SBHG-1 HEAT SINK-PS;-,-,-,SILVER,HOLE 18.5mm, 2 ASSY LED GUIDE;-,-,SL-255D,RED/GRN ASSY H/S;-,REGULATOR,AA62-00066B,FML-G1 GREASE-SILICON;SC102,JAPAN DIODE-RECTIFIER;FML-G12S,200V, DIODE-RECTIFIERFMG-G2CS,1000V,3A,TO-22 IC-VOLTAGEREGULATOR78R05,TO-220F,4P SCREW-TAPTITE;RH,+,2S,M3,L6,ZP HEAT SINK;D2,D3,AL ,T1.0,89,70,-,AA62-00 ASSY-POWER,CORD;EP2/YES,H/C450,ME301P POWER-CORD;-,EP2/YES,SPT-2 18AWGx2C,2.4m HOLDER P CORD;PP,VO,BLK,KE-002 ASSY-H/S;SOUND AMP,AA62-30181J,TDA7266S GREASE-SILICON;SC102,JAPAN IC-POWERAMP;7266,ZIP,15P,-,DUAL,26dB,PL SCREW-TAPTITE;RH,+,2S,M3,L10,ZPC(YEL),SW HEAT-SINK,ES,AL6063 EXTR,2,WHT,40MM,AN ASSY H/S;-,PWM,AA62-30181H,KA3S1265RD GREASE-SILICON;SC102,JAPAN SCREW-TAPTITE;RH,+,2S,M3,L10,ZPC(YEL),SW MICA;DPM-04,MICA,22x29x0.15mm IC HYBRID;KA3A1265RD,CN5039,5Pin,-50to12 BRACKET-IC;-,-,SECC100,T1.0,-,KA2S0680, HEATSINK-ES;-,AL6063EXTR.,2,WHT,50MM,ASSY-H/S;LA62-30180K,LA7845 IC-LINEAR;LA7845SIPVERTICALAMP SCREW-TAPTITE;RH,+,2S,M3,L10,ZPC(YEL),SW HEATSINK-ES;-,A6063EXTR,-,WHT,50/13,-, ASSY-AUTO;MAIN;KS3A,27,SEA/SECA DIODE;1N4148,100V,300mA,1V,8nS,TAPING DIODE;1N4148,100V,300mA,1V,8nS,TAPING DIODE;1N4148,100V,300mA,1V,8nS,TAPING DIODE;1N4148,100V,300mA,1V,8nS,TAPING DIODE;1N4148,100V,300mA,1V,8nS,TAPING DIODE;1N4148,100V,300mA,1V,8nS,TAPING DIODE;1N4148,100V,300mA,1V,8nS,TAPING DIODE;1N4148,100V,300mA,1V,8nS,TAPING DIODE;1N4148,100V,300mA,1V,8nS,TAPING DIODE;1N4148,100V,300mA,1V,8nS,TAPING DIODE;1N4148,100V,300mA,1V,8nS,TAPING DIODE;1N4148,100V,300mA,1V,8nS,TAPING DIODE-RECTIFIER;1R5GU41,400V,1 DIODE-RECTIFIER;1R5GU41,400V,1 DIODE-RECTIFIER;RG10V,400V,1.5 DIODE-RECTIFIER;RG10V,400V,1.5 DIODE-RECTIFIER;RH1A,600V,0.6A, DIODE-RECTIFIER;RU20A,600V,1.5 DIODE-RECTIFIER;RU20A,600V,1.5 DIODE-RECTIFIER;TVR10G,400V,1. DIODE-RECTIFIER;TVR10G,400V,1. DIODE-RECTIFIER;TVR10G,400V,1. DIODE-RECTIFIER;TVR10G,400V,1. DIODE-RECTIFIER;1N5397GP,600V,1.5A,DO-2 DIODE-RECTIFIER;1N4004,400V,1A,DO-41 DIODE-RECTIFIER;1N4004,400V,1A,DO-41 DIODE-RECTIFIER;1N4004,400V,1A,DO-41 DIODE-RECTIFIER;1N4004,400V,1A,DO-41 DIODE-RECTIFIER;1N4004,400V,1A,DO-41 DIODE-RECTIFIER;1N4004,400V,1A,DO-41 DIODE-RECTIFIER;1N4004,400V,1A,DO-41 DIODE-ZENER;MTZJ5.6B,5.6V,5.45-5.73V,500 DIODE-ZENER;MTZJ5.6B,5.6V,5.45-5.73V,500 DIODE-ZENER;MTZJ5.6B,5.6V,5.45-5.73V,500 DIODE-ZENER;MTZJ5.6B,5.6V,5.45-5.73V,500 DIODE-ZENER;MTZJ5.6B,5.6V,5.45-5.73V,500 DIODE-ZENER;MTZJ5.6B,5.6V,5.45-5.73V,500 DIODE-ZENER;MTZJ5.6B,5.6V,5.45-5.73V,500
Samsung Electronics
7-1
Electrical Parts List
Loc. No.
Code No.
Description ; Specification
Remark
Loc. No.
Code No.
Description ; Specification
Remark
!
!
!
! !
4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4
DZ802 DZ806 DZ901 DZ902 DZ905 DZ906 DZ907 DZ908 DZ909 DZ910 DZ306 DZ804 DZ602 DZ803 DZ305 DZ203 DZR01S DZ801 DZ808 DZ401 DZ302 DZ303 DZ304 D203 D204 D205 D206 D901 D902 D903 D904 QR01S Q802 Q201 Q202 Q203 Q204 Q601 Q901 Q902 Q903 Q904 Q905 Q906 Q907 Q908 Q911 QR02S DZ805 IC904 VP801S VX801S R223 R248 R249 R250 R934 R916 R918 R303 R412 R809 R411 R422 R825 R228 R207 R213 R822 J904 R102 R103 R203 R204 R231 R232 R604
0403-000508 0403-000508 0403-000508 0403-000508 0403-000508 0403-000508 0403-000508 0403-000508 0403-000508 0403-000508 0403-000700 0403-000700 0403-000720 0403-001167 0403-001221 0403-001321 0403-001321 0403-001322 0403-001322 0403-001325 0403-001329 0403-001329 0403-001329 0404-000156 0404-000156 0404-000156 0404-000156 0404-000156 0404-000156 0404-000156 0404-000156 0501-000283 0501-000369 0501-000389 0501-000389 0501-000389 0501-000389 0501-000389 0501-000389 0501-000389 0501-000389 0501-000389 0501-000389 0501-000389 0501-000389 0501-000389 0501-000389 0501-000389 1203-001217 1203-001943 1405-000152 1405-000152 2001-000003 2001-000003 2001-000003 2001-000003 2001-000003 2001-000007 2001-000009 2001-000016 2001-000020 2001-000022 2001-000028 2001-000037 2001-000066 2001-000117 2001-000221 2001-000232 2001-000273 2001-000281 2001-000281 2001-000281 2001-000281 2001-000281 2001-000281 2001-000281 2001-000281
DIODE-ZENER;MTZJ5.6B,5.6V,5.45-5.73V,500 DIODE-ZENER;MTZJ5.6B,5.6V,5.45-5.73V,500 DIODE-ZENER;MTZJ5.6B,5.6V,5.45-5.73V,500 DIODE-ZENER;MTZJ5.6B,5.6V,5.45-5.73V,500 DIODE-ZENER;MTZJ5.6B,5.6V,5.45-5.73V,500 DIODE-ZENER;MTZJ5.6B,5.6V,5.45-5.73V,500 DIODE-ZENER;MTZJ5.6B,5.6V,5.45-5.73V,500 DIODE-ZENER;MTZJ5.6B,5.6V,5.45-5.73V,500 DIODE-ZENER;MTZJ5.6B,5.6V,5.45-5.73V,500 DIODE-ZENER;MTZJ5.6B,5.6V,5.45-5.73V,500 DIODE-ZENER;TZP33A,33V,31-35V, DIODE-ZENER;TZP33A,33V,31-35V, DIODE-ZENER;MTZJ9.1B,9.1V,8.57-9.01V,500 DIODE-ZENER;MTZJ30D,30V,29.02-30.51V,500 DIODE-ZENER;UZ39BSB,35.36-37.19V,500MW,D DIODE-ZENER;MTZJ6.8C,6.66-7.01V,500mW,DO DIODE-ZENER;MTZJ6.8C,6.66-7.01V,500mW,DO DIODE-ZENER;MTZJ8.2B,7.78-8.19V,500mW,DO DIODE-ZENER;MTZJ8.2B,7.78-8.19V,500mW,DO DIODE-ZENER;MTZJ15C,14.35-15.09V,500mW,D DIODE-ZENER;MTZJ24B,22.61-23.77V,500mW, DIODE-ZENER;MTZJ24B,22.61-23.77V,500mW, DIODE-ZENER;MTZJ24B,22.61-23.77V,500mW, DIODE-SCHOTTKY;RB441Q,10V,100MA,DO-34,TP DIODE-SCHOTTKY;RB441Q,10V,100MA,DO-34,TP DIODE-SCHOTTKY;RB441Q,10V,100MA,DO-34,TP DIODE-SCHOTTKY;RB441Q,10V,100MA,DO-34,TP DIODE-SCHOTTKY;RB441Q,10V,100MA,DO-34,TP DIODE-SCHOTTKY;RB441Q,10V,100MA,DO-34,TP DIODE-SCHOTTKY;RB441Q,10V,100MA,DO-34,TP DIODE-SCHOTTKY;RB441Q,10V,100MA,DO-34,TP TRANSISTOR;KSA539-Y(TAPG)/YTAM TRANSISTOR;KSC2331-Y(TAPG) TRANSISTOR;KSC815-Y(TAPG)/YTAM TRANSISTOR;KSC815-Y(TAPG)/YTAM TRANSISTOR;KSC815-Y(TAPG)/YTAM TRANSISTOR;KSC815-Y(TAPG)/YTAM TRANSISTOR;KSC815-Y(TAPG)/YTAM TRANSISTOR;KSC815-Y(TAPG)/YTAM TRANSISTOR;KSC815-Y(TAPG)/YTAM TRANSISTOR;KSC815-Y(TAPG)/YTAM TRANSISTOR;KSC815-Y(TAPG)/YTAM TRANSISTOR;KSC815-Y(TAPG)/YTAM TRANSISTOR;KSC815-Y(TAPG)/YTAM TRANSISTOR;KSC815-Y(TAPG)/YTAM TRANSISTOR;KSC815-Y(TAPG)/YTAM TRANSISTOR;KSC815-Y(TAPG)/YTAM TRANSISTOR;KSC815-Y(TAPG)/YTAM IC-POST,ADJUSTREG;431,T0-92,3P,4.58MIL,P IC-VOL.DETECTOR;7025,T0-92,3P,PLASTIC VARISTOR;560V,2500A,14X8.5MM,T VARISTOR;560V,2500A,14X8.5MM,T R-CARBON;330OHM,5%,1/8W,AA,TP, R-CARBON;330OHM,5%,1/8W,AA,TP, R-CARBON;330OHM,5%,1/8W,AA,TP, R-CARBON;330OHM,5%,1/8W,AA,TP, R-CARBON;330OHM,5%,1/8W,AA,TP, R-CARBON;3KOHM,5%,1/8W,AA,TP,1 R-CARBON;20KOHM,5%,1/8W,AA,TP, R-CARBON(S);1OHM,5%,1/2W,AA,TP R-CARBON(S);22OHM,5%,1/2W,AA,T R-CARBON(S);33OHM,5%,1/2W,AA,T R-CARBON(S);100OHM,5%,1/2W,AB, R-CARBON(S);330OHM,5%,1/2W,AA, R-CARBON(S);10KOHM,5%,1/2W,AA, R-CARBON(S);68ohm,5%,1/2W,AA,TP,2.4x6.4m R-CARBON;1.2KOHM,5%,1/8W,AA,TP R-CARBON;1.3KOHM,5%,1/8W,AA,TP R-CARBON;100KOHM,5%,1/8W,AA,TP R-CARBON;100OHM,5%,1/8W,AA,TP, R-CARBON;100OHM,5%,1/8W,AA,TP, R-CARBON;100OHM,5%,1/8W,AA,TP, R-CARBON;100OHM,5%,1/8W,AA,TP, R-CARBON;100OHM,5%,1/8W,AA,TP, R-CARBON;100OHM,5%,1/8W,AA,TP, R-CARBON;100OHM,5%,1/8W,AA,TP, R-CARBON;100OHM,5%,1/8W,AA,TP,
! !
!
4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4
R605 R612 R613 R627 R628 R723 R907 R909 R925 R940 R941 R942 R947 R202 R205 R206 R211 R243 R245 R246 R309 R310 R601 R602 R606 R609 R620 R629 R715 R716 R935 R952 RR07S RR10S R208 R214 R209 R216 R234 R235 R252 R603 R607 R608 R817 R902 R910 R911 R912 R914 R924 R929 R930 R936 RR08S R236 R237 R238 R247 R932 R943 R215 R823 R915 R949 R105 R251 R833 R901 R903 R904 R905 R921 R927 R928 R937 R938
2001-000281 2001-000281 2001-000281 2001-000281 2001-000281 2001-000281 2001-000281 2001-000281 2001-000281 2001-000281 2001-000281 2001-000281 2001-000281 2001-000290 2001-000290 2001-000290 2001-000290 2001-000290 2001-000290 2001-000290 2001-000290 2001-000290 2001-000290 2001-000290 2001-000290 2001-000290 2001-000290 2001-000290 2001-000290 2001-000290 2001-000290 2001-000290 2001-000290 2001-000290 2001-000405 2001-000411 2001-000429 2001-000429 2001-000429 2001-000429 2001-000429 2001-000429 2001-000429 2001-000429 2001-000429 2001-000429 2001-000429 2001-000429 2001-000429 2001-000429 2001-000429 2001-000429 2001-000429 2001-000429 2001-000429 2001-000515 2001-000515 2001-000515 2001-000515 2001-000515 2001-000515 2001-000522 2001-000522 2001-000577 2001-000660 2001-000702 2001-000734 2001-000734 2001-000734 2001-000734 2001-000734 2001-000734 2001-000734 2001-000734 2001-000734 2001-000734 2001-000734
R-CARBON;100OHM,5%,1/8W,AA,TP, R-CARBON;100OHM,5%,1/8W,AA,TP, R-CARBON;100OHM,5%,1/8W,AA,TP, R-CARBON;100OHM,5%,1/8W,AA,TP, R-CARBON;100OHM,5%,1/8W,AA,TP, R-CARBON;100OHM,5%,1/8W,AA,TP, R-CARBON;100OHM,5%,1/8W,AA,TP, R-CARBON;100OHM,5%,1/8W,AA,TP, R-CARBON;100OHM,5%,1/8W,AA,TP, R-CARBON;100OHM,5%,1/8W,AA,TP, R-CARBON;100OHM,5%,1/8W,AA,TP, R-CARBON;100OHM,5%,1/8W,AA,TP, R-CARBON;100OHM,5%,1/8W,AA,TP, R-CARBON;10KOHM,5%,1/8W,AA,TP, R-CARBON;10KOHM,5%,1/8W,AA,TP, R-CARBON;10KOHM,5%,1/8W,AA,TP, R-CARBON;10KOHM,5%,1/8W,AA,TP, R-CARBON;10KOHM,5%,1/8W,AA,TP, R-CARBON;10KOHM,5%,1/8W,AA,TP, R-CARBON;10KOHM,5%,1/8W,AA,TP, R-CARBON;10KOHM,5%,1/8W,AA,TP, R-CARBON;10KOHM,5%,1/8W,AA,TP, R-CARBON;10KOHM,5%,1/8W,AA,TP, R-CARBON;10KOHM,5%,1/8W,AA,TP, R-CARBON;10KOHM,5%,1/8W,AA,TP, R-CARBON;10KOHM,5%,1/8W,AA,TP, R-CARBON;10KOHM,5%,1/8W,AA,TP, R-CARBON;10KOHM,5%,1/8W,AA,TP, R-CARBON;10KOHM,5%,1/8W,AA,TP, R-CARBON;10KOHM,5%,1/8W,AA,TP, R-CARBON;10KOHM,5%,1/8W,AA,TP, R-CARBON;10KOHM,5%,1/8W,AA,TP, R-CARBON;10KOHM,5%,1/8W,AA,TP, R-CARBON;10KOHM,5%,1/8W,AA,TP, R-CARBON;180OHM,5%,1/8W,AA,TP, R-CARBON;18KOHM,5%,1/8W,AA,TP, R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;220OHM,5%,1/8W,AA,TP, R-CARBON;220OHM,5%,1/8W,AA,TP, R-CARBON;220OHM,5%,1/8W,AA,TP, R-CARBON;220OHM,5%,1/8W,AA,TP, R-CARBON;220OHM,5%,1/8W,AA,TP, R-CARBON;220OHM,5%,1/8W,AA,TP, R-CARBON;22KOHM,5%,1/8W,AA,TP, R-CARBON;22KOHM,5%,1/8W,AA,TP, R-CARBON;2KOHM,5%,1/8W,AA,TP,1 R-CARBON;33KOHM,5%,1/8W,AA,TP, R-CARBON;39KOHM,5%,1/8W,AA,TP, R-CARBON;4.7KOHM,5%,1/8W,AA,TP R-CARBON;4.7KOHM,5%,1/8W,AA,TP R-CARBON;4.7KOHM,5%,1/8W,AA,TP R-CARBON;4.7KOHM,5%,1/8W,AA,TP R-CARBON;4.7KOHM,5%,1/8W,AA,TP R-CARBON;4.7KOHM,5%,1/8W,AA,TP R-CARBON;4.7KOHM,5%,1/8W,AA,TP R-CARBON;4.7KOHM,5%,1/8W,AA,TP R-CARBON;4.7KOHM,5%,1/8W,AA,TP R-CARBON;4.7KOHM,5%,1/8W,AA,TP R-CARBON;4.7KOHM,5%,1/8W,AA,TP
7-2
Samsung Electronics
Electrical Parts List
Loc. No.
Code No.
Description ; Specification
Remark
Loc. No.
Code No.
Description ; Specification
Remark
!
!
!
! !
!
! !
4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4
RR02S R224 R225 R226 R614 R615 R616 R617 R812 R831 R919 R920 R931 R933 RR09S R816 R244 R210 R106 R824 R917 RR04S R923 R241 R709 R913 C251 C253 R242 R704 R705 R719 R720 RR06S L905 L401 R404 R808 R418 RR430S R421 R820 R818 R432 R429 R805 R806 R813 R832 R423 R810 R428 RP802S RY802S R426 R401 R402 R233 R434 R802 R803 R804 R433 R403 R436 R409 R410 R305 R306 R835 R836 R212 RR05S R313 R417 R301 R420
2001-000766 2001-000780 2001-000780 2001-000780 2001-000780 2001-000780 2001-000780 2001-000780 2001-000780 2001-000780 2001-000780 2001-000780 2001-000780 2001-000780 2001-000780 2001-000780 2001-000786 2001-000812 2001-000864 2001-000864 2001-000878 2001-000908 2001-000924 2001-000938 2001-000938 2001-000947 2001-000969 2001-000969 2001-000969 2001-000969 2001-000969 2001-000969 2001-000969 2001-000977 2001-000995 2001-001038 2001-001038 2001-001079 2001-001088 2001-001088 2001-001093 2001-001096 2001-001113 2001-001122 2001-001139 2001-001150 2001-001150 2001-001153 2001-001153 2001-001155 2001-001178 2001-001184 2002-001010 2002-001013 2003-000540 2003-000586 2003-000586 2003-000592 2003-000664 2003-001025 2003-001025 2003-001025 2003-001042 2003-001091 2003-002008 2003-002009 2003-002009 2003-002157 2003-002157 2003-002211 2003-002211 2004-000218 2004-000531 2004-001137 2004-001382 2004-001397 2004-001402
R-CARBON;43KOHM,5%,1/8W,AA,TP, R-CARBON;470ohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;470ohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;470ohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;470ohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;470ohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;470ohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;470ohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;470ohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;470ohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;470ohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;470ohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;470ohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;470ohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;470ohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;470ohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;47KOHM,5%,1/8W,AA,TP, R-CARBON;5.6Kohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;56Kohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;56Kohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;6.2KOHM,5%,1/8W,AA,TP R-CARBON ;62Kohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;680ohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON ;68ohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON ;68ohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;7.5KOHM,5%,1/8W,AA,TP R-CARBON;75OHM,5%,1/8W,AA,TP,1 R-CARBON;75OHM,5%,1/8W,AA,TP,1 R-CARBON;75OHM,5%,1/8W,AA,TP,1 R-CARBON;75OHM,5%,1/8W,AA,TP,1 R-CARBON;75OHM,5%,1/8W,AA,TP,1 R-CARBON;75OHM,5%,1/8W,AA,TP,1 R-CARBON;75OHM,5%,1/8W,AA,TP,1 R-CARBON;8.2Kohm,5%,1/8W,AA,TP,1.8x3.2m R-CARBON;820OHM,5%,1/8W,AA,TP, R-CARBON(S);0.56OHM,5%,1/2W,AA,TP,2.4X6. R-CARBON(S);0.56OHM,5%,1/2W,AA,TP,2.4X6. R-CARBON(S);15OHM,5%,1/2W,AB,T R-CARBON(S);1KOHM,5%,1/2W,AA,TP,2.4X6.4 R-CARBON(S);1KOHM,5%,1/2W,AA,TP,2.4X6.4 R-CARBON(S);2.2KOHM,5%,1/2W,AA,TP,2.4X6. R-CARBON(S);2.2OHM,5%,1/2W,AA, R-CARBON(S);270KOHM,5%,1/2W,AA R-CARBON/METALFILM;RD1/2T3.9KR-CARBON(S);39KOHM,5%,1/2W,AA, R-CARBON(S);470KOHM,5%,1/2W,AA R-CARBON(S);470KOHM,5%,1/2W,AA R-CARBON(S);47OHM,5%,1/2W,AA,T R-CARBON(S);47OHM,5%,1/2W,AA,T R-CARBON(S);5.6Kohm,5%,1/2W,AA,TP,2.4x6. R-CARBON(S);680OHM,5%,1/2W,AA, R-CARBON(S);750KOHM,5%,1/2W,AB R-COMPOSITION;1.8MOHM,5%,1/2W,AA,TP,3.7X R-COMPOSITION;4.7MOhm,5%,1/2W,AA,TP,3.7X R-METALOXIDE(S);1KOHM,5%,2W,AD R-METALOXIDE(S);22KOHM,5%,2W,A R-METALOXIDE(S);22KOHM,5%,2W,A R-METALOXIDE(S);22OHM,5%,2W,AD R-METAL OXIDE(S);330HM,5%,2W,AF,TP,4X12M R-METALOXIDE(S);15KOHM,5%,2W,A R-METALOXIDE(S);15KOHM,5%,2W,A R-METALOXIDE(S);15KOHM,5%,2W,A R-METALOXIDE(S);5.6KOHM,5%,2W,AF,TP,3.9X R-METALOXIDE;RS2RT(S)100-J10R R-METAL OXIDE(S);18KOHM,5%,2W,AF,TP,3.9X R-METALOXIDE(S);390OHM,5%,2W,A R-METALOXIDE(S);390OHM,5%,2W,A R-METAL OXIDE;220OHM,5%,2W,AG,TP,6X16MM R-METAL OXIDE;220OHM,5%,2W,AG,TP,6X16MM R-METALOXIDE(S)91Kohm,5%,2W,AG,TP,3x R-METALOXIDE(S)91Kohm,5%,2W,AG,TP,3x R-METAL;10KOHM,1%,1/8,1.8X3.2M R-METAL;20Kohm,1%,1/2W,AA,TP,3.3x9mm R-METAL;6.8KOHM,1%,1/8W,AA,TP,1.8*3.2M R-METAL(S);13KOHM,1%,1/2W,AA,TP,2.4X6.4M R-METAL(S);4.7KOHM,1%,1/2W,AA, R-METAL(S);6.8KOHM,1%,1/2W,AA,
!
!
!
4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4
R811 R821 RR03S R819 R302 R314 R415 R315 R405 R414 R304 RR01S R828 R827 R413 R424 R425 R829 C424 C656 C657 C804 C805 C828 C814 C401 C403 C421 CR01S C601 C419 C817 C819 C822 C654 C910 C911 C224 C225 C303 C115 C116 C244 C245 C113 C246 C248 C627 C629 C638 C639 C642 C644 C701 C709 C710 C711 C647 C903 C211 C607 C608 C905 C632 C247 C908 C218 C219 C220 C252 C254 C901 C919 C921 C922 C649 C821
2004-001408 2004-001891 2004-001897 2004-001983 2004-001984 2004-001986 2004-004048 2004-004970 2008-000253 2008-000253 2008-000254 2008-000264 2008-000266 2008-000284 2008-001018 2008-001018 2008-001018 2008-001029 2201-000132 2201-000304 2201-000304 2201-000332 2201-000332 2201-000374 2201-000406 2201-000556 2201-000556 2201-000556 2201-000556 2201-000558 2201-000599 2201-000599 2201-000599 2201-000599 2201-000611 2201-000980 2201-000980 2201-002031 2201-002031 2201-002103 2202-000121 2202-000121 2202-000121 2202-000121 2202-000127 2202-000210 2202-000210 2202-000231 2202-000231 2202-000231 2202-000231 2202-000231 2202-000231 2202-000231 2202-000243 2202-000243 2202-000243 2202-000286 2202-000719 2202-000796 2202-000796 2202-000796 2202-000796 2202-000806 2202-000849 2202-000863 2202-002037 2202-002037 2202-002037 2202-002037 2202-002037 2202-002037 2202-002037 2202-002037 2202-002037 2301-000108 2301-000192
R-METAL(S);91KOHM,1%,1/2W,AA,T R-METAL(S);133KOHM,1%,1/2W,AA, R-METAL(S);43.2KOHM,1%,1/2W,AA R-METAL;2.49KOHM,1%,1/2W,AA,TP,2.4X6.4 R-METAL;26.7KOHM,1%,1/2W,AA,TP R-METAL;35.7KOHM,1%,1/2W,AA,TP R-METAL(S);3.9Kohm,1%,1/2W,AA,TP,2.5x6.5 R-METAL(S);62Kohm,1%,1/8W,AA,TP,1.8x3.2m R-FUSIBLE(S);0.47OHM,5%,1W,AF, R-FUSIBLE(S);0.47OHM,5%,1W,AF, R-FUSIBLE(S);0.68OHM,5%,2W,AF, R-FUSIBLE(S);1OHM,5%,1W,AF,TP, R-FUSIBLE(S);1OHM,5%,2W,AF,TP, R-FUSIBLE(S);0.1OHM,10%,2W,AF,TP,3.9X10M R-FUSIBLE(S);0.47OHM,10%,2W,AF R-FUSIBLE(S);0.47OHM,10%,2W,AF R-FUSIBLE(S);0.47OHM,10%,2W,AF R-FUSIBLE(S);5.6OHM,5%,2W,AF,T C-CERAMIC,DISC;100PF,10%,500V,Y5P,6X3MM, C-CERAMIC,DISC0.001nF,0.25pF,50V,NP0,TP C-CERAMIC,DISC0.001nF,0.25pF,50V,NP0,TP C-CERAMIC,AC;CK45PTAPGE250V222 C-CERAMIC,AC;CK45PTAPGE250V222 C-CERAMIC,DISC;220pF,5%,50V,CH,TP,12.5x3 C-CERAMIC,HIC;CK45(T)B2KV271-K C-CERAMIC,DISC;470PF,10%,500V, C-CERAMIC,DISC;470PF,10%,500V, C-CERAMIC,DISC;470PF,10%,500V, C-CERAMIC,DISC;470PF,10%,500V, C-CERAMIC,DISC;470PF,10%,50V,Y C-CERAMIC,DISC;560PF,10%,500V, C-CERAMIC,DISC;560PF,10%,500V, C-CERAMIC,DISC;560PF,10%,500V, C-CERAMIC,DISC;560PF,10%,500V, C-CERAMIC,DISC;56PF,5%,50V,NPO C-CERAMIC,DISC;30PF,5%,50V,NPO,5.0X3.0,5 C-CERAMIC,DISC;30PF,5%,50V,NPO,5.0X3.0,5 C-CERAMIC,DISC;5pF,0.25pF,50V,NPO,TP,5x3 C-CERAMIC,DISC;5pF,0.25pF,50V,NPO,TP,5x3 C-CERAMIC,DISC;0.015nF,5%,500V,NP0,TP,6. C-CERAMIC,MLC-AXIAL;100PF,10%, C-CERAMIC,MLC-AXIAL;100PF,10%, C-CERAMIC,MLC-AXIAL;100PF,10%, C-CERAMIC,MLC-AXIAL;100PF,10%, C-CERAMIC,MLC-AXIAL;10NF,+80-2 C-CERAMIC,MLC-AXIAL;270pF,10%,50V,Y5P,TP C-CERAMIC,MLC-AXIAL;270pF,10%,50V,Y5P,TP C-CERAMIC,MLC-AXIAL;330PF,10%,50V,Y5P,3. C-CERAMIC,MLC-AXIAL;330PF,10%,50V,Y5P,3. C-CERAMIC,MLC-AXIAL;330PF,10%,50V,Y5P,3. C-CERAMIC,MLC-AXIAL;330PF,10%,50V,Y5P,3. C-CERAMIC,MLC-AXIAL;330PF,10%,50V,Y5P,3. C-CERAMIC,MLC-AXIAL;330PF,10%,50V,Y5P,3. C-CERAMIC,MLC-AXIAL;330PF,10%,50V,Y5P,3. C-CERAMIC,MLC-AXIAL;33PF,5%,50 C-CERAMIC,MLC-AXIAL;33PF,5%,50 C-CERAMIC,MLC-AXIAL;33PF,5%,50 C-CERAMIC,MLC-AXIAL;56PF,5%,50 C-CERAMIC,MLC-AXIAL;6.8nF,20%,16V,Y5R,TP C-CERAMIC,MLC-AXIAL;1NF,10%,50 C-CERAMIC,MLC-AXIAL;1NF,10%,50 C-CERAMIC,MLC-AXIAL;1NF,10%,50 C-CERAMIC,MLC-AXIAL;1NF,10%,50 C-CERAMIC,MLC-AXIAL;220pF,10%,50V,Y5P,TP C-CERAMIC,MLC-AXIAL;18pF,5%,50V,CH,TP,3. C-CERAMIC;CKOAX7R50VT561-KUP050561 C-CERAMIC,MLC-AXIAL;100NF,+80-20 C-CERAMIC,MLC-AXIAL;100NF,+80-20 C-CERAMIC,MLC-AXIAL;100NF,+80-20 C-CERAMIC,MLC-AXIAL;100NF,+80-20 C-CERAMIC,MLC-AXIAL;100NF,+80-20 C-CERAMIC,MLC-AXIAL;100NF,+80-20 C-CERAMIC,MLC-AXIAL;100NF,+80-20 C-CERAMIC,MLC-AXIAL;100NF,+80-20 C-CERAMIC,MLC-AXIAL;100NF,+80-20 C-FILM,PEF;1.5NF,5%,50V,6.5X3.0X5.5MM,5M C-FILM,PEF;1NF,5%,50V,5.3X10MM
Samsung Electronics
7-3
Electrical Parts List
Loc. No.
Code No.
Description ; Specification
Remark
Loc. No.
Code No.
Description ; Specification
Remark
!
4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4
C902 C212 C416 C411 C213 C412 C306 C228 C230 C809 C810 C811 C101 C103 C105 C909 C415 C610 C611 C420 C425 C409 C807 C305 C304 C408 C233 C234 C235 C236 C308 C907 CR04S C206 C214 C216 C240 C605 C620 C635 C646 C825 C829 C831 C837 C839 C914 C916 C637 C640 C641 C643 C912 C816 C210 C826 C302 C307 C413 C617 C917 C201 C301 C604 C106 C841 C818 C237 C208 C217 C636 C402 C404 C102 C422 C634 C832
2301-000192 2301-000224 2301-000224 2301-000232 2301-000310 2301-000313 2301-000342 2301-000356 2301-000356 2301-000356 2301-000356 2301-000356 2301-000383 2301-000383 2301-000383 2301-000383 2301-000445 2301-000445 2301-000445 2301-001065 2301-001259 2301-001268 2301-001397 2305-000149 2305-000285 2305-000382 2305-000411 2305-000411 2305-000411 2305-000411 2305-000411 2305-000411 2305-000412 2305-000665 2305-000665 2305-000665 2305-000665 2305-000665 2305-000665 2305-000665 2305-000665 2305-000665 2305-000665 2305-000665 2305-000665 2305-000665 2305-000665 2305-000665 2401-000027 2401-000027 2401-000027 2401-000027 2401-000027 2401-000262 2401-000287 2401-000287 2401-000360 2401-000360 2401-000493 2401-000493 2401-000493 2401-000603 2401-000603 2401-000603 2401-000611 2401-000611 2401-000722 2401-000914 2401-001026 2401-001026 2401-001026 2401-001397 2401-001397 2401-001513 2401-001527 2401-001840 2401-001840
C-FILM,PEF;1NF,5%,50V,5.3X10MM C-FILM,PEF;22NF,5%,50V,7.4X3.9 C-FILM,PEF;22NF,5%,50V,7.4X3.9 C-FILM,PEF;3.3NF,5%,50V,8.1X4. C-FILM,PEF;68NF,5%,50V,8.0X8.5 C-FILM,PEF;8.2NF,5%,100V,7X3.2 C-FILM,PEF;2.2nF,5%,50V,TP,7.4x3.9x13mm, C-FILM,PEF;47nF,5%,50V,TP,7.5x4.0x6.5,5m C-FILM,PEF;47nF,5%,50V,TP,7.5x4.0x6.5,5m C-FILM,PEF;47nF,5%,50V,TP,7.5x4.0x6.5,5m C-FILM,PEF;47nF,5%,50V,TP,7.5x4.0x6.5,5m C-FILM,PEF;47nF,5%,50V,TP,7.5x4.0x6.5,5m C-FILM,PEF;10nF,5%,50V,TP,6x7x3.2mm,5mm C-FILM,PEF;10nF,5%,50V,TP,6x7x3.2mm,5mm C-FILM,PEF;10nF,5%,50V,TP,6x7x3.2mm,5mm C-FILM,PEF;10nF,5%,50V,TP,6x7x3.2mm,5mm C-FILM,PEF;4.7nF,5%,50V,TP,5.5x7x3mm,5mm C-FILM,PEF;4.7nF,5%,50V,TP,5.5x7x3mm,5mm C-FILM,PEF;4.7nF,5%,50V,TP,5.5x7x3mm,5mm C-FILM,MPPF;47NF,55,630V,TP,19 C-FILM,MPPF;100nF,5%,400V,TP,19x8x16,7.5 C-FILM,PPF;33nF,5%,630V,TP,20x11x17,7.5 C-FILM,PPF;2.2nF,5%,1.2kV,TP,15x8.5x13.5 C-FILM;CF922N100VT104-J-40/105 C-FILM,MPEF;220NF,5%,100V,-,5M C-FILM,MPEF;4.7NF,5%,400V,TP,-,5MM. C-FILM,MPEF;470NF,5%,50V,7.3X4 C-FILM,MPEF;470NF,5%,50V,7.3X4 C-FILM,MPEF;470NF,5%,50V,7.3X4 C-FILM,MPEF;470NF,5%,50V,7.3X4 C-FILM,MPEF;470NF,5%,50V,7.3X4 C-FILM,MPEF;470NF,5%,50V,7.3X4 C-FILM,MPEF;470NF,5%,63V,-,5MM C-FILM;104J, 60V,5MM TAPING C-FILM;104J, 60V,5MM TAPING C-FILM;104J, 60V,5MM TAPING C-FILM;104J, 60V,5MM TAPING C-FILM;104J, 60V,5MM TAPING C-FILM;104J, 60V,5MM TAPING C-FILM;104J, 60V,5MM TAPING C-FILM;104J, 60V,5MM TAPING C-FILM;104J, 60V,5MM TAPING C-FILM;104J, 60V,5MM TAPING C-FILM;104J, 60V,5MM TAPING C-FILM;104J, 60V,5MM TAPING C-FILM;104J, 60V,5MM TAPING C-FILM;104J, 60V,5MM TAPING C-FILM;104J, 60V,5MM TAPING C-AL;4.7UF,20%,50V,GP,5*11MM,5MEA C-AL;4.7UF,20%,50V,GP,5*11MM,5MEA C-AL;4.7UF,20%,50V,GP,5*11MM,5MEA C-AL;4.7UF,20%,50V,GP,5*11MM,5MEA C-AL;4.7UF,20%,50V,GP,5*11MM,5MEA C-AL;100UF,20%,160V,GP,16X25MM,5MM, C-AL;100UF,20%,16V,WT,6X11MM,5 C-AL;100UF,20%,16V,WT,6X11MM,5 C-AL;100UF,20%,50V,GP,8X11MM,5 C-AL;100UF,20%,50V,GP,8X11MM,5 C-AL;10UF,20%,50V,WT,5X11MM,5M C-AL;10UF,20%,50V,WT,5X11MM,5M C-AL;10UF,20%,50V,WT,5X11MM,5M C-AL;1UF,20%,50V,GP,5X11MM,5MM C-AL;1UF,20%,50V,GP,5X11MM,5MM C-AL;1UF,20%,50V,GP,5X11MM,5MM C-AL;1UF,20%,50V,WT,5X11MM,5MM C-AL;1UF,20%,50V,WT,