Text preview for : 05_Alignment & Adjustment.pdf part of SAMSUNG CK 3351 EZ5X MEDION CK 3351 EZ5X MEDION
Back to : Service_Manual.part1.rar | Home
Alignment and Adjustments
4. Alignment and Adjustments
4-1 Preadjustment
4-1-1 Factory Mode
1. Do not attempt these adjustments in the Video Mode. 2. The Factory Mode adjustments are necessary when either the EEPROM (IC902) or the CRT is replaced. 3. Do not tamper with the "Adjustment" screen of the Factory Mode menu. This screen is intended only for factory use.
4-1-3 When CRT Is Replaced
1. Make the following adjustments AFTER setting up after setting up purity and convergence : White Balance Sub-Brightness Vertical Center Vertical Size Horizontal Size Fail Safe (This adjustment must be the last step). 2. If the EEPROM or CRT is replaced, set SC and PVA to 10 and 45 (Factory mode). SC : 14, 16 Inch : 0 20, 21 Inch : 10
4-1-2 When EEPROM (IC902) Is Replaced
1. When IC902 is replaced all adjustment data revert to initial values. It is necessary to re-program this data. 2. After IC902 is replaced, warm up the TV for 10 seconds.
4-2 Factory/Service Mode
4-2-1 Procedure for the "Adjustment" Mode
1. This mode uses the standard remote control. The Service Mode is activated by entering the following remote-control sequence : (1) SLEEPFACTORY. (2) STAND-BYP.STDHELPSLEEP POWER ON. 2. The "SERVICE (FACTORY)" message will be displayed. The Service Mode has four components: Adjustment, Test Pattern, Option Bytes and Reset. 3. Access the Adjustment Mode by pressing the "VOLUME" keys ( Up or Down). The adjustment parameters are listed in the accompanying table, and selected by pressing the CHANNEL keys (v ,w). 4. Selection sequences for the PAL system: DOWN or UP key: AGC>VCO>SBT>SCT>SCR>SC>RG> GG>BG>CDL>BLU>PSL>PVS>PVA>PHS 5. Selection sequences for the NTSC system: DOWN or UP key: AGC>VCO>SBT>SCT>SCR>SC>RG> GG>BG>CDL>BLU>NSL>NVS>NVA>NHS 6. The VOLUME keys increase or decrease the adjustment values, (stored in the non-volatile memory when Adjustment Mode is cancelled). 7. Cancel the Adjustment Mode by re-pressing the "FACTORY" or Power OFF.
Samsung Electronics
4-1
Alignment and Adjustments
4-2-2 Main Adjustment Parameter
Table 4-1 Main Adjustment Parameter (Zilog, Phlips µ-com) FUNCTION AUTO GAIN CONTROL SUB BRIGHT SUB CONTRAST SUB COLOR RED DRIVE GAIN GREEN DRIVE GAIN BLUE DRIVE GAIN PAL VERTICAL SLOPE PAL VERTICAL SHIFT PAL VERTICAL AMPLITUDE PAL HORIZONTAL SHIFT NTSC VERTICAL SLOPE NTSC VERTICAL SHIFT NTSC VERTICAL AMPLITUDE NTSC HORIZONTAL SHIFT VOLTAGE CONTROL OSCILLATOR S-CORRECTION TTX SUB-CONTRAST CATHODE DRIVE LEVEL BLUE STRETCH MODE OSD ABBREVIATION AGC SBT SCT SCR RG GG BG PSL PVS PVA PHS NSL NVS NVA NHS VCO SC TSS CDL BLU RANGE 0 ~ 63 STEP 0 ~ 23 STEP 0 ~ 23 STEP 0 ~ 23 STEP 0 ~ 63 STEP 0 ~ 63 STEP 0 ~ 63 STEP 0 ~ 63 STEP 0 ~ 63 STEP 0 ~ 63 STEP 0 ~ 63 STEP 0 ~ 63 STEP 0 ~ 63 STEP 0 ~ 63 STEP 0 ~ 63 STEP 0 ~ 128 STEP 0 ~ 63 STEP 0 ~ 63 STEP 0 ~ 7 STEP 0 ~ 3 STEP INITIAL DATA 32 7 7 13 32 32 32 20 32 TDA8374 45 32 20 32 45 32 64 32 16 3 2 TDA8842 REMARKS
NOTE : PVS,PVA, PHS, NVS, NVA,NHS parameters must be aligned using both the 50Hz and 60Hz vertical-field rates.
4-2
Samsung Electronics
Alignment and Adjustments
4-2-3 Test Pattern (Aging Mode)
1. This mode can be used during servicing, or for confirming that the convergence and purity adjustments are correct. 2. Access the Test Pattern parameters by pressing a CHANNEL keys (v ,w) while the Service Mode is on. The cursor will move to the test pattern. Press the VOLUME keys. On-screen display: ° ·RED ° ·GREEN ° ·BLUE ° ·AGING
NON -TTX MICOM ONLY TTX MICOM
3. AGING Mode (Reference Only) This pattern is used for pre-heating the CRT during manufacturing--it is accessed in the factory by twice pressing the "SLEEP FACTORYFACTORY " key, then white pattern will be displayed. Even if the TV power is cut off, the Aging Mode is not cancelled, The aging mode is cancelled by repressing the "FACTORY" key or pressing the local "CH UP/DOWN" key. The patterns are displayed at 5 sec intervals : NON-TTX Micom only.
4-2-4 Option Bytes
In the Service Mode, various can be selected via the Option Bytes (8 bits each). Example:
SYSTEM OSD DISPLAY BYTE 0 : 8 BYTE 1 : 0
BIT 6 L (BIT :0)
BIT 5 L (BIT : 0)
BIT 4 L (BIT : 0) L (BIT : 0)
BIT 3 H (BIT : 8) L (BIT : 0)
BIT 2 L (BIT : 0) L (BIT : 0)
BIT 1 L (BIT : 0) L (BIT : 0)
BIT 0 L (BIT : 0) L (BIT : 0)
TDA8374, CK SYSTEM, RCA JACK SYSTEM OSD DISPLAY BYTE 0 : 11 L (BIT : 1) H (BIT : 0) L (BIT : 0) H (BIT : 0) L (BIT : 1)
Samsung Electronics
4-3
Alignment and Adjustments
4-2-4 (A) OPTION BYTE TABLE
BYTE BIT D7 D6 LOW (0) 16:9 not functional during "Zoom" in the A/V Mode No Child Lock CH Up/down functional in the A/V mode (SCART Jack) SOUND-I SYSTEM USED
D2 D1 0 1 0 1 COLOR SYSTEM CK : PAL ONLY (NO OSD) CW : -. RF : AUTOPAL SECAMNT4.43 -. A/V : AUTOPALSECAM NT4.43 NT3.58 CB : -RF : PAL ONLY -A/V : AUTOPAL NT4.43NT3.58 CS : - RF : AUTOPAL SECAM NT4.43NT 3.58 -A/V : AUTOPAL SECAM NT4.43 NT3.58
HIGH (1)
Application MICOM -
16:9 functional during "Zoom" in the A/V Mode Child Lock CH Up/down not functional in the A/V mode (RCA Jack) SOUND-I SYSTEM NOT USED
SOUND SYSTEM B/GD/K I B/GD/K I B/G ONLY ( No OSD) B/GD/K I NT M
D5 D4 B Y T E 0
D3
D2
0 0 1 1
D1
D0
D7 D6 0 1 0 1
TDA8374
Southeast/Middle East Asia /Africa English Only English/Arabian English/Arabian/French English Only Vietnam/India English Only
TDA8842
Thailand/Malaysia English Only English/Thai English/Malay English/Thai /Malay CIS
Onechip
China
D7
0 0 1 1
English Only English only English/CIS English /Chinese
English/Vietnamese English/Indonesian English/Vietnamese /Indonesian
D6
B Y T E 1
D5 D4 D3 D2
AFT ON (always) Existing sharpness level No Auto Power On NTSC : 25KHz (NTSC Table) PAL : 50KHz (PAL Table)
D1 D0 0 1 0 1
AFT OFF (after fine tuning) Sharpness level Up Auto Power ON NTSC : 25KHz (NTSC Table) PAL : 50KHZ (PAL Table)
System DIG D/K I NT-M
March 12, 1997 Last State Memory PAL Table always used in the A/V Mode (March 12, 1997) Sound system during the auto search (All should be set for the system which is selected during the Factory Reset.)
D1
0 0
D0
1 1
4-4
Samsung Electronics
Alignment and Adjustments
4-2-4 (B) TTX MICOM (SPM-197EE/ER/EG) OPTION TABLE (FOR EUROPE)
BYTE BIT D7 D6 LOW (0) 3 BAND 16:9 not functional during zoom in the A/V mode (NORMAL-ZOOM) LED RED AT STAND-BY CH Up/down functional in the A/V mode (SCART Jack) P-STD MAX D2 0 0 D1 1 1 D0 D7 D6 Western OSD :English/German/French/Dutch/ Italian/Spanish/Swedish Eastern OSD :English/Croatian/Rumanian/ Hungarian/Hungarian/Polish/Czech D1 0 1 0 1 SOUND SYSTEM B/G D/K : CK MODEL AUTO (NO OSD) HIGH (1) UHF ONLY 16:9 functional during zoom in the A/V mode (NORMAL-ZOOM-16:9) LED GREEN AT STAND-BY (POLAND) CH Up/down not functional in the A/V mode (RCA Jack) P-STD NORMAL COLOR SYSTEM ALL Application MICOM ALL ALL (BASIC : LOW)
D5 D4 B Y T E 0
ALL (J900 DELETE AT H) ALL
D3
ALL (BASIC : HIGH)
D2
I ONLY (NO OSD) : CI, CII MODEL B/G ONLY (NO OSD) : CB, CX MODEL NOT USED TDA8374A NOT USED
TDA8842
ALL ALL (FIX : LOW) SPM- 197EE ONLY used * SPM-197ER : English/Russian/ Bulgarian *SPM-197EG: English/Greek/ Yugosiavian ALL (BASIC : HIGH) ALL (BASIC : HIGH) ALL (RF VOL. CURVE) BASIC : LOW (AV VOL. CURVE : PAL CURVE) Sound system during the auto search (All should be set for the system which is selected during the Factory Reset.) Note : Available when the sound is B/G D/K in the Byte 0
D5
B Y T E 1
D4 D3
Existing sharpness level (when using TDA6108 RGB AMP) No Auto Power On NTSC : 25KHz (NTSC TABLE) PAL : 50KHz (PAL TABLE)
Sharpness level up (when using TDA6107Q AMP) Auto Power On NTSC : 25KHz (NTSC TABLE) PAL : 27KHz (PAL TABLE)
D2
D1
NOT USED (FIX : LOW)
D0
B/G SOUND
D/K SOUND
q P-STD Classification (CON./BRI./SHRP.COL.)
D3 BIT STANDARD MODE 0 1 100/50/50/50 90/50/50/50 DYAMIC MODE 100/50/75/50 100/50/50/50 MOVIE MODE 90/50/75/50 75/55/50/50 MILD MODE 60/50/75/50 60/50/50/50 CUSTOM MODE 100/50/50/50 90/55/25/50
q Function Required : 1. PICTURE OFF (after 15 minutes) during no signal 3. No BLUE SCREEN Samsung Electronics
2. AUDIO MUTE (during no signal) 4. NO TIMER (CLOCK ON/OFF) 4-5
Alignment and Adjustments
4-2-4 (C) TTX MICOM (SPM-197EP/EPR/EA) OPTION TABLE (FOR MIDDLE EAST)
BYTE BIT D7 D6 LOW (0) NOT USED 16:9 not functional during zoom (NORMAL-ZOOM) NOT USED CH Up/down functional in the A/V mode (SCART Jack) SOUND-I SYSTEM USED
D2 0 0 1 1 D1 0 1 0 1 COLOR SYSTEM CK : AUTO (No OSD) CW : -. RF : AUTOPAL SECAMNT4.43 -. A/V : AUTOPALSECAM NT4.43 NT3.58 CB : -RF : PAL ONLY (No OSD) -A/V : AUTOPAL NT4.43NT3.58 CS : - RF : AUTOPAL SECAM NT4.43NT 3.58 -A/V : AUTOPAL SECAM NT4.43 NT3.58
HIGH (1)
Application MICOM ALL (FIX : LOW)
16:9 functional during zoom (NORMAL-ZOOM-16:9)
EP is an OPTION during A/V (BASIC : LOW) ALL (FIX : LOW) ALL
D5 D4 B Y T E 0
CH Up/down not functional in the A/V mode (RCA Jack) SOUND-I SYSTEM NOT USED
SOUND SYSTEM (?)B/GD/K (?)B/GD/K I B/G ONLY ( No OSD) (?)B/GD/K I NT M
D3
ALL
D2
D1
D0 D7 D6 D5 D4 D3 B Y T E 1
TDA8374A
TDA8842
EP VERSION : TDA8374A ONLY
NOT USED Existing Sharpness level (when using the TDA6108 RGB AMP) No Auto Power On NTSC : 25KHz (NTSC TABLE) PAL : 50KHz (PAL TABLE Sharpness level up (when using the TDA6107Q RGB AMP) Auto Power On NTSC : 25KHz (NTSC TABLE) PAL : 27KHz (PAL TABLE
ALL (FIX : LOW)
ALL (BASIC : HIGH) ALL (BASIC : HIGH) ALL (RF VOL. CURVE) BASIC : LOW (AV VOL. CURVE : PAL CURVE) Sound system during the auto search (All should be set for the system which is selected during the Factory Reset.) Note : A single sound in the Byte 0 is unavailable
D2
D1 D1 0 0 D0 1 1
D0 0 1 0 1
SYSTEM B/G D/K I ?(B/G & D/K OR M) /EP VER. : M
q OSD Language by MiCOM 1. Persian (for Iran) : English/Persian (Iranian) 2. Arab (Middle East, Africa) : English/French/Arabian q Function Required : 1. PICTURE OFF (after 15 minutes) during no signal 3. No BLUE SCREEN 2. AUDIO MUTE (during no signal) 4. No TIMER (CLOCK ON/OFF)
4-6
Samsung Electronics
Alignment and Adjustments
4-2-4 (D) TTX MICOM (SPM-193EE/EER) OPTION TABLE (FOR EUROPE)
BYTE BIT D7 LOW (0) 3 BAND HIGH (1) UHF ONLY REMARK SZM-193EE : H NOT functional SZM-193EER : Basic Specification : LOW
D6
16:9 not functional during zoom in the A/V mode (NORMAL-ZOOM) LED RED AT STAND-BY CH Up/down functional in the A/V mode (SCART Jack) P-STD MAX D2 0 0 D1 0 1 0 1
16:9 functional during zoom in the A/V mode (NORMAL-ZOOM-16:9) LED GREEN AT STAND-BY CH Up/down not functional in the A/V mode (RCA Jack) P-STD NORMAL
D5 D4 B Y T E 0
POLAND (J900 DELETE AT H) BASIC : LOW
D3
ALL (BASIC : HIGH)
D2
SOUND SYSTEM B/G D/K : CK MODEL
COLOR SYSTEM
I ONLY (NO OSD) : CI, CII MODEL B/G ONLY (NO OSD) : CB, CX MODEL NOT USED TDA8374A
D7 D6 0 1 0 1 OSD Language English/German/French/Dutch/ Italian/Spanish/Swedish English/Romanian/Hungarian/ Croatian/Polish/Czech/Russian English/Bulgarian/Greek/Yugo
D1
1 1
AUTO (NO OSD)
SOUND SYSTEM OPTION
D0
TDA8842
IC201 (ONE-CHIP) OPTION
D7
0 0 1
Language Option
D6
1
D5 B Y T E 1 D4 D3 D2
AFT ON (always) Existing Sharpness level (when using TDA6108 RGB AMP) No Auto Power On NTSC : 25KHz (NTSC TABLE) PAL : 50KHz (PAL TABLE)
AFT OFF (after fine tuning) Sharpness level up (when using TDA6107Q AMP) Auto Power On NTSC : 25KHz (NTSC TABLE) PAL : 27KHz (NTSC TABLE)
BASIC : LOW BASIC : HIGH BASIC: HIGH RF VOL. : CURVE, BASIC : LOW (AV VOL. CURVE:PAL CURVE) Sound system during the Auto search (All should be set for the system which is selected during the Factory Reset.) Note: Only available during the specification of CK model in the Byte 0
D1
NOT USED (FIX : LOW)
D0
SOUND B/G
SOUND D/K
q P-STD Classification (CON./BRI./SHRP./COL.)
D3 BIT STANDARD MODE 0 1 100/50/50/50 90/50/50/50 DYAMIC MODE 100/50/75/50 100/50/50/50 MOVIE MODE 90/50/75/50 75/55/50/50 MILD MODE 60/50/75/50 60/50/50/50 CUSTOM MODE 100/50/50/50 90/55/25/50
q Function Required : 1. PICTURE OFF (after 15 minutes) during no signal 2. AUDIO MUTE (during no signal) 3. No BLUE SCREEN during no RF signal (Blue screen during A/V 4. NO TIMER Samsung Electronics 4-7
Alignment and Adjustments
4-2-4 (E) TTX MICOM (SZM-193EA/EAR/EV) OPTION TABLE
BYTE BIT D7 D6 LOW (0) LINE STEREO OFF 16:9 not function during zoom in the A/V mode (Normal-ZOOM) CHILD LOCK OFF CH Up/down functional in the A/V mode (SCART Jack) SOUND-I SYSTEM USED
D2 D1 0 1 0 1 COLOR SYSTEM CK : AUTO (No OSD)
HIGH (1) LINE STEREO ON 16:9 functional during zoom in the A/V mode (NORMAL-ZOOM-16:9) CHILD LOCK ON CH Up/down not functional in the A/V mode (RCA Jack) SOUND-I SYSTEM NOT USED
SOUND SYSTEM B/GD/K
Application MICOM ALL BASIC : LOW
D5 D4 B Y T E 0
ALL (No SZM193EA) ALL
D3
ALL
D2
0 0 1 1
CW : -. RF : AUTOPAL SECAMNT4.43 B/GD/K I -. A/V : AUTOPALSECAM NT4.43 NT3.58 CB : -RF : PAL ONLY -A/V : AUTOPAL NT4.43NT3.58 CS : - RF : AUTOPAL SECAM NT4.43NT 3.58 -A/V : AUTOPAL SECAM NT4.43 NT3.58 B/G ONLY ( No OSD) B/GD/K I NT M
D1
D0
D7 0 0
TDA8374A
D6 Middle East/Africa Version 0 1 0 1 English ONLY English/Arabian English/Arabian/French English ONLY
TDA8842
Asia Version (SZM193EV) English only English/Indonesian/Malay/Thai/Vietnamese English/Vietnamese/Indonesian English/Thai/Malay
ALL (No SZM193EA)
D7
D6
1 1
D5 B Y T E 1 D4 D3
AFT ON (always) Existing Sharpness level (when using TDA6108 RGB AMP) No Auto Power On NTSC : 25KHz(NTSC TABLE) PAL : 50 KHz (PAL TABLE)
AFT OFF after fine tuning (for India) Sharpness level up (when using TDA6107Q RGB AMP) Auto Power On NTSC : 25KHz (NTSC TABLE) PAL : 27KHz (NTSC TABLE)
ALL (No SZM-193EA) ALL (BASIC : HIGH) ALL (BASIC : HIGH) ALL (RF VOL.: HIGH) BASIC : LOW (AV VOL. CURVE : PAL CURVE) Initial sound system during the auto search (All should be for the system which is selected during the Factory Reset.) Note : Unavailable during the CB model in the byte 0
D2
D1
D0 0 1 0 1
SYSTEM B/G D/K I NT-M
D1
0 0
D0
1 1
q Function Required : 1. PICTURE OFF (after 15 minutes) during no signal 3. No BLUE SCREEN
2. AUDIO MUTE (during no signal) 4. TIMER (CLOCK ON/OFF)
4-8
Samsung Electronics
Alignment and Adjustments
4-2-4 (F) TTX MICOM (SZM-191ER) OPTION TABLE (FOR RUSSIA, OCEANIA)
BYTE BIT D7 D6 LOW (0) NOT USED 16:9 not functional during zoom in the A/V mode (NORMAL-ZOOM) 16:9 functional during zoom in the A/V mode (NORMAL-ZOOM-16:9) HIGH (1) Application MICOM FIX : LOW BASIC : LOW
D5 D4 B Y T E 0
NOT USED CH Up/down functional in the A/V mode (SCART Jack) SOUND-I SYSTEM USED
D2 D1 0 1 0 1 COLOR SYSTEM CK : AUTO (No OSD) CW : -. RF : AUTOPAL SECAMNT4.43 -. A/V : AUTOPALSECAM NT4.43 NT3.58 CB : -RF : PAL ONLY (No OSD) -A/V : AUTOPAL NT4.43NT3.58 CS : - RF : AUTOPAL SECAM NT4.43NT 3.58 -A/V : AUTOPAL SECAM NT4.43 NT3.58
FIX : LOW
CH Up/down not functional in the A/V mode (RCA Jack) SOUND-I SYSTEM NOT USED
SOUND SYSTEM B/GD/K B/GD/K I B/G OSD B/GD/K I NT M
D3
BASIC : LOW
D2
0 0 1 1
D1
D0 D7 D6 D5 D4 B Y T E 1 D3 D2
TDA8374A NOT USED English ONLY AFT ON (always) Existing Sharpness level (when using TDA6108 RGB AMP) No Auto Power On NTSC : 25KHz (NTSC TABLE) PAL : 50KHz (PAL TABLE)
D1 D0 0 1 0 1
TDA8842
IC201(ONE-CHIP) OPTION FIX : LOW
English/Russian AFT OFF (after fine tuning) Sharpness level up (when using the TDA6107Q RGB AMP) Auto Power On NTSC : 25KHz (NTSC TABLE) PAL : 27KHz (PAL TABLE)
System DIG D/K I NT-M
Language option BASIC : LOW BASIC : HIGH
BASIC : HIGH ALL (RF VOL. CURVE) , BASIC :LOW (AV VOL. CURVE: PAL CURVE) Initial sound system during the auto search (All should be set for the system which is selected during the Factory Reset.) Note : Unavailable during the CB model in the Byte 0
D1
0 0
D0
1 1
q Function Required : 1. PICTURE OFF (after 15 minutes) during no signal 3. BLUE SCREEN ON/OFF
2. AUDIO MUTE during no signal 4. No TIMER CLOCK
q The SZM191ER is to be diverted to Australia/New Zealand because of the non-functionality of RGB (of pin 21). (OPTION BYTE : 55/1C) When using TDA8842 N1, the BLOOMING check is required.
Samsung Electronics
4-9
Alignment and Adjustments
4-2-4 (G) TTX MICOM (SZM-193EVR) OPTION TABLE (FOR ASIA)
BYTE BIT D7 D6 LOW (0) LINE STEREO OFF 16:9 not function during zoom in the A/V mode (Normal-ZOOM) CHILD LOCK OFF CH Up/down functional in the A/V mode (SCART Jack) SOUND-I SYSTEM USED
D2 D1 0 1 0 1 COLOR SYSTEM CK : AUTO (No OSD)
HIGH (1) LINE STEREO ON 16:9 functional during zoom in the A/V mode (NORMAL-ZOOM-16:9) CHILD LOCK ON CH Up/down not functional in the A/V mode (RCA Jack) SOUND-I SYSTEM NOT USED
SOUND SYSTEM B/GD/K
Application MICOM
BASIC : LOW
D5 D4 B Y T E 0
BASIC : HIGH
D3
D2
0 0 1 1
CW : -. RF : AUTOPAL SECAMNT4.43 B/GD/K I -. A/V : AUTOPALSECAM NT4.43 NT3.58 CB : -RF : PAL ONLY -A/V : AUTOPAL NT4.43NT3.58 CS : - RF : AUTOPAL SECAM NT4.43NT 3.58 -A/V : AUTOPAL SECAM NT4.43 NT3.58 B/G ONLY ( No OSD) B/GD/K I NT M
D1
D0
D7 0 0
TDA8374A
D6 0 1 0 1 English ONLY OSD Language
TDA8842
IC201 (ONE-CHIP) OPTION
D7
English/Indonesian/Malay/Thai/Vietnamese English/Vietnamese/Indonesian English/Thai/Malay
Language option
D6
1 1
D5 B Y T E 1 D4 D3
AFT ON (always) CLOCK DISPLAY OFF No Auto Power On NTSC : 25KHz(NTSC TABLE) PAL : 50 KHz (PAL TABLE)
AFT OFF (after fine tuning) CLOCK DISPLAY ON Auto Power On NTSC : 25KHz (NTSC TABLE) PAL : 27KHz (NTSC TABLE)
BASIC : LOW(India : HIGH) BASIC : LOW Indonesia : HIGH BASIC : HIGH ALL (RF VOL.: HIGH) BASIC : LOW (AV VOL. CURVE : PAL CURVE) Initial sound system during the auto search (All should be set for the system which is selected during the Factory Reset.) Note : Unavailable during the CB model in the Byte 0
D2
D1
D0 0 1 0 1
SYSTEM B/G D/K I NT-M
D1
0 0
D0
1 1
q Function Required : 1. PICTURE OFF (after 15 minutes) during no signal 3. BLUE SCREEN On/off
2. AUDIO MUTE during no signal 4. TIMER CLOCK ON/OFF
4-10
Samsung Electronics
Alignment and Adjustments
4-2-4 (H) NON TTX MICOM (SZM-193EV2) OPTION TABLE (FOR ASIA)
BYTE BIT D7 D6 LOW (0) LINE STEREO OFF 16:9 not function during zoom (Normal-ZOOM) CHILD LOCK OFF CH Up/down functional in the A/V mode (SCART Jack) SOUND-I SYSTEM USED
D2 D1 0 1 0 1 COLOR SYSTEM CK : AUTO (No OSD) CW : -. RF : AUTOPAL SECAMNT4.43 -. A/V : AUTOPALSECAM NT4.43 NT3.58 CB : -RF : PAL ONLY (No OSD) -A/V : AUTOPAL NT4.43NT3.58 CS : - RF : AUTOPAL SECAM NT4.43NT 3.58 -A/V : AUTOPAL SECAM NT4.43 NT3.58
HIGH (1) LINE STEREO ON 16:9 functional during zoom (NORMAL-ZOOM-16:9) CHILD LOCK ON CH Up/down not functional in the A/V mode (RCA Jack) SOUND-I SYSTEM NOT USED
SOUND SYSTEM (?)B/GD/K (?)B/GD/K I B/G ONLY ( No OSD) (?)B/GD/K I NT M
Application MICOM
BASIC : LOW
D5 D4 B Y T E 0
BASIC : HIGH
D3
D2
0 0 1
D1
1
D0
D7 0 0
TDA8374A
D6 0 1 0 1 English ONLY OSD Language
TDA8842
IC201 (ONE-CHIP) OPTION
D7
English/Indonesian/Malay/Thai/Vietnamese English/Vietnamese/Indonesian English/Thai/Malay
Language option
D6
1 1
D5 B Y T E 1 D4 D3
AFT ON (always) CLOCK DISPLAY OFF No Auto Power On NTSC : 25KHz(NTSC TABLE) PAL : 50 KHz (PAL TABLE)
AFT OFF (after fine tuning) CLOCK DISPLAY ON Auto Power On NTSC : 25KHz (NTSC TABLE) PAL : 27KHz (NTSC TABLE)
BASIC : LOW(India : HIGH) BASIC : LOW Indonesia : HIGH BASIC : HIGH RF VOL.CURVE BASIC : LOW (AV VOL. CURVE : PAL CURVE) Initial sound system during the auto search (All should be set for the system which is selected during the Factory Reset.) Note: Unavailable during the CB model in the Byte 0
D2
D1
D0 0 1 0 1
SYSTEM B/G D/K I ?) B/G & D/K OR M
D1
0 0
D0
1 1
q Function Required : 1. PICTURE OFF (after 15 minutes) during no signal 3. BLUE SCREEN On/off
2. AUDIO MUTE during no signal 4. TIMER Clock On/Off
Samsung Electronics
4-11
Alignment and Adjustments
4-2-4 (I) TTX MICOM (SPM-193EA2) OPTION TABLE (FOR MIDDLE EAST ASIA/AFRICA)
BYTE BIT D7 D6 LOW (0) LINE STEREO OFF 16:9 not functional during zoom in the A/V mode (NORMAL-ZOOM) CHILD LOCK OFF CH Up/down functional in the A/V mode (SCART Jack) SOUND-I SYSTEM USED
D2 0 0 1 1 D1 0 1 0 1 COLOR SYSTEM CK : AUTO (No OSD) CW : -. RF : AUTOPAL SECAMNT4.43 -. A/V : AUTOPALSECAM NT4.43 NT3.58 CB : -RF : PAL ONLY (No OSD) -A/V : AUTOPAL NT4.43NT3.58 CS : - RF : AUTOPAL SECAM NT4.43NT 3.58 -A/V : AUTOPAL SECAM NT4.43 NT3.58
HIGH (1) LINE STEREO ON 16:9 functional during zoom in the A/V mode (NORMAL-ZOOM-16:9) CHILD LOCK ON CH Up/down not functional in the A/V mode (RCA Jack) SOUND-I SYSTEM NOT USED
SOUND SYSTEM (?)B/GD/K (?)B/GD/K I B/G ONLY ( No OSD) (?)B/GD/K I NT M
Application MICOM
BASIC : LOW
D5 D4 B Y T E 0
D3
D2
D1
D0 D7 D6 D5 D4 D3
TDA8374A NOT USED AFT ON (always) Existing Sharpness level (when using the TDA6108 RGB AMP) No Auto Power On NTSC : 25KHz (NTSC TABLE) PAL : 50KHz (PAL TABLE)
TDA8842
IC201 (ONE-CHIP) OPTION FIX : LOW
AFT OFF (after fine tuning) Sharpness level up (when using the TDA6107Q RGB AMP) Auto Power On NTSC : 25KHz (NTSC TABLE) PAL : 27KHz (PAL TABLE)
BASIC : LOW BASIC : HIGH BASIC : HIGH ALL (RF VOL. CURVE) BASIC : LOW (AV VOL. CURVE : PAL CURVE) Initial sound system during the auto search (All should be set for the system which is selected during the Factory Reset.) Note : Unavailable during the CB model in the Byte 0
B Y T E 1
D2
D1 D1 0 0 D0 1 1
D0 0 1 0 1
SYSTEM B/G D/K I ? B/G & D/K OR M
q Function Required : 1. PICTURE OFF (after 15 minutes) during no signal 3. BLUE SCREEN On/Off
2. AUDIO MUTE (during no signal) 4. No Timer Clock On/Off
4-12
Samsung Electronics
Alignment and Adjustments
4-2-4 (J) TTX MICOM (SZM-193EC) OPTION TABLE (FOR CHINA)
BYTE BIT D7 D6 LOW (0) LINE STEREO OFF 16:9 not functional during zoom in the A/V mode (NORMAL-ZOOM) CHILD LOCK OFF CH Up/down functional in the A/V mode (SCART Jack) SOUND-I SYSTEM USED
D2 D1 0 1 0 1 COLOR SYSTEM CK : AUTO (No OSD) CW : -. RF : AUTOPAL SECAMNT4.43 -. A/V : AUTOPALSECAM NT4.43 NT3.58 CB : -RF : PAL ONLY (No OSD) -A/V : AUTOPAL NT4.43NT3.58 CS : - RF : AUTOPAL SECAM NT4.43NT 3.58 -A/V : AUTOPAL SECAM NT4.43 NT3.58
HIGH (1) LINE STEREO ON 16:9 functional during zoom in the A/V mode (NORMAL-ZOOM-16:9) CHILD LOCK ON CH Up/down not functional in the A/V mode (RCA Jack) SOUND-I SYSTEM NOT USED
SOUND SYSTEM B/GD/K B/GD/K I B/G OSD B/GD/K I NT M
Remark BASIC : LOW BASIC : LOW
D5 D4 B Y T E 0
BASIC : LOW
D3
BASIC : HIGH
D2
0 0 1 1
D1
D0 D7 D6 D5 D4 B Y T E 1 D3 D2
TDA8374A NOT USED English ONLY AFT ON (always) Existing Sharpness level (when using TDA6108 RGB AMP) No Auto Power On NTSC : 25KHz (NTSC TABLE) PAL : 50KHz (PAL TABLE)
D1 D0 0 1 0 1
TDA8842
IC201(ONE-CHIP) OPTION FIX : LOW
English/Russian AFT OFF (after fine tuning) Sharpness level up (when using the TDA6107Q RGB AMP) Auto Power On NTSC : 25KHz (NTSC TABLE) PAL : 27KHz (PAL TABLE)
System DIG D/K I NT-M
Language option BASIC : LOW BASIC : HIGH
BASIC : HIGH ALL (RF VOL. CURVE) , BASIC:LOW (AV VOL. CURVE: PAL CURVE) Initial sound system during the auto search (All should be set for the system which is selected during the Factory Reset.) Note : Unavailable during the CD model in the Byte 0
D1
0 0
D0
1 1
q Function Required : 1. PICTURE OFF (after 15 minutes) during no signal 3. BLUE SCREEN On/Off
2. AUDIO MUTE during no signal 4. TIMER CLOCK On/Off
Samsung Electronics
4-13
Alignment and Adjustments
4-2-4 (K) NON TTX MICOM (SZM-191EC) OPTION TABLE (FOR CHINA)
BYTE BIT D7 D6 LOW (0) NOT USED 16:9 not functional during zoom (NORMAL-ZOOM) NOT USED CH Up/down functional in the A/V mode (SCART Jack) SOUND-I SYSTEM USED
D2 D1 0 1 0 1 COLOR SYSTEM CK : AUTO (No OSD) CW : -. RF : AUTOPAL SECAMNT4.43 -. A/V : AUTOPALSECAM NT4.43 NT3.58 CB : -RF : PAL ONLY (No OSD) -A/V : AUTOPAL NT4.43NT3.58 CS : - RF : AUTOPAL SECAM NT4.43NT 3.58 -A/V : AUTOPAL SECAM NT4.43 NT3.58
HIGH (1)
Application MICOM FIX : LOW
16:9 functional during zoom (NORMAL-ZOOM-16:9)
BASIC : LOW
D5 D4 B Y T E 0
FIX : LOW
CH Up/down not functional in the A/V mode (RCA Jack) SOUND-I SYSTEM NOT USED
SOUND SYSTEM B/GD/K B/GD/K I B/G OSD B/GD/K I NT M
D3
BASIC : LOW
D2
0 0 1 1
D1
D0 D7 D6 D5 D4 B Y T E 1 D3 D2
TDA8374A NOT USED English ONLY AFT ON (always) Existing Sharpness level (when using TDA6108 RGB AMP) No Auto Power On NTSC : 25KHz (NTSC TABLE) PAL : 50KHz (PAL TABLE)
D1 D0 0 1 0 1
TDA8842
IC201(ONE-CHIP) OPTION FIX : LOW
English/Russian AFT OFF (after fine tuning) Sharpness level up (when using the TDA6107Q RGB AMP) Auto Power On NTSC : 25KHz (NTSC TABLE) PAL : 27KHz (PAL TABLE)
System DIG D/K I NT-M
Language option BASIC : LOW BASIC : HIGH
BASIC : HIGH ALL (RF VOL. CURVE) , BASIC :LOW (AV VOL. CURVE: PAL CURVE) Initial sound system during the auto search (All should be set for the system which is selected during the Factory Reset.) Note : Unavailable during the CD model in the Byte 0
D1
0 0
D0
1 1
q Function Required : 1. PICTURE OFF (after 15 minutes) during no signal 3. BLUE SCREEN ON/OFF
2. AUDIO MUTE during no signal 4. No TIMER CLOCK
4-14
Samsung Electronics
Alignment and Adjustments
4-2-5 RESET
The Reset Mode is used during factory inspection. Function Reset: 1. 2. 3. 4. 5. 6. 7. 8. 9. Channels Sort System Timer Blue Screen Child Lock Picture Volume CH. Skip Add/Erase Non Auto off off off standard 26 Erased
4-3 Other Adjustments
4-3-1 General
1. Usually, a color TV needs only slight touchup adjustment upon installation. Check the basic characteristics such as height, horizontal and vertical sync and focus. 2. The picture should have good black and white details. There should be no objectionable color shading; if color shading is present, perform the purity and convergence adjustments described below. 3. Use the specified test equipment or its equivalent. 4. Correct impedance matching is essential. 5. Avoid overload. Excessive signal from a sweep generator might overload the front-end of the TV. When inserting signal markers, do not allow the marker generator to distort test results. 6. Connect the TV only to an AC power source with voltage and frequency as specified on the backcover nameplate. 7. Do not attempt to connect or disconnect any wires while the TV is turned on. Make sure that the power cord is disconnected before replacing any parts. 8. To protect against shock hazard, use an isolation transformer.
4-3-2 Automatic Degaussing
A degaussing coil is mounted around the picture tube, so that external degaussing after moving the TV should be unnecessary. But the receiver must be properly degaussed upon installation. The degaussing coil operates for about 1 second after the power is switched ON. If the set has been moved or turned in a different direction, disconnect its AC power for at least 10 minutes. If the chassis or parts of the cabinet become magnetized, poor color purity will result. If this happens, use an external degaussing coil. Slowly move the degaussing coil around the faceplate of the picture tube and the sides and front of the receiver. Slowly withdraw the coil to a distance of about 6 feet before removing power.
Samsung Electronics
4-15
Alignment and Adjustments
4-3-3 High Voltage Check
CAUTION: There is no high voltage adjustment on this chassis. The B+ power supply must be set to +125 volts (Full color bar input and normal picture level).
4-3-6 Purity Adjustment
1. Warm up the receiver for at least 20 minutes. 2. Plug in the CRT deflection yoke and tighten the clamp screw. 3. Plug the convergence yoke into the CRT and set in as shown in Fig. 4-2. 4. Input a black and white signal. 5. Fully demagnetize the receive by applying an external degaussing coil. 6. Turn the CONTRAST and BRIGHTNESS controls to maximum. 7. Loosen the clamp screw holding the yoke. Slide the yoke backward or forward to provide vertical green belt. (Fig. 4-3). 8. Tighten the convergence yoke. 9. Slowly move the deflection yoke forward, and adjust for the best overall green screen. 10. Temporarily tighten the deflection yoke. 11. Produce blue and red rasters by adjusting the low-light controls. Check for good purity in each field. 12. Tighten the deflection yoke.
1. Connect a digital voltmeter to the second anode of the picture tube. 2. Turn on the TV. Set the Brightness and Contrast controls to minimum (zero beam current). 3. The high voltage should not exceed 27.5KV. 4. Adjust the Brightness and contrast controls to both extremes. Ensure that the high voltage does not exceed 27.5KV under any conditions.
4-3-4 FOCUS Adjustment
1. Input a black and white signal. 2. Adjust the tuning control for the clearest picture. 3. Adjust the FOCUS control for well defined scanning lines in the center area of the screen.
4-3-5 Cathode Voltage Adjustment (Screen Adjustment)
1. Connect CRT socket pin GK to an oscilloscope probe. 2. Input a gray scale pattern. (Use a pattern generator, PM5518) 3. Use the P mode key (on the remote control) for the STANDARD picture. 4. Adjust the Screen VR (on the FBT) so that the _ voltage on the oscilloscope becomes 130+2.5V (See Fig. 4-1).
_ 130 + 2.5V
GND
_ 14, 16" :120 + 2.5V + 20, 21" : 130 _ 2.5V
Fig. 4-1 4-16 Samsung Electronics
Alignment and Adjustments
4 Pole Magnet 6 Pole Magnet Clamper Screw 2 Pole Magnet
2 POLE PURITY
ADJUST THE ANGL (VERTICAL LINES)
YOKE CLAMP SCREW 6 POLE CONVERGENCE 4 POLE CONVERGENCE
Fig. 4-2 Convergence Magnet Assembly
Vertical Green Belt
31m/m
Fig. 4-3 Center Convergence Adjustment
4-3-7 White Balance Adjustment
(a) Set up 1. Warm up the TV for at least 30 minutes in the Aging Mode (OSD White). This mode is displayed by entering the following sequence: 1 SLEEP FACTORY FACTORY 2. Input a Toshiba pattern. (b) High-Light Adjustment 2 1. Set SBT to 2.0 fL in the Factory Service Mode with using CA100. See Fig. 4-4 . 2. Adjust RG,BG so that the levels are suitable to each local area. Fig. 4-4 (c) Low-Light Adjustment 1. Set SCT to 50.0 fL in the Factory Service Mode with using CA100. See Fig. 4-4 x.
Samsung Electronics
4-17
Alignment and Adjustments
4-3-8 Center Convergence Adjustment
1. Warm up the receiver for at least 20 minutes. 2. Adjust the two tabs of the 4 pole magnets to change the angle between them. Superimpose the red and blue vertical lines in the center area of the screen. 3. Adjust the Brightness and Contrast controls for a well defined picture. 4. Adjust the two-tab pairs of the 4 pole magnets, and change the angle between them. Superimpose the red and the blue vertical lines in the center area of the screen. 5. Turn the both tabs at the same time, keeping the angle constant, and superimpose the red and blue horizontal line in the center of the screen. 6. Adjust the two-tab pairs of the 6-pole magnets to superimpose the red and blue line onto the green. (Changing the angle affects the vertical lines, and rotating both magnets affects the horizontal lines.) 7. Repeat adjustments 2~6, if necessary. 8. Since the 4-pole magnets and 6-pole magnets interact, the dot movement is complex (Fig. 4-5).
BLUE
RED
RED/BLUE
GREEN
BLUE RED
RED/BLUE GREEN
4-Pole Magnet Movement
6-Pole Magnet Movement
Fig. 4-5 Center Convergence Adjustment
4-3-9 VCO Adjustment
1. Turn on the TV. VCO 63 SIGNAL DETECTOR AFA RGB
8V I2C-BUS 5V
SET
SD : ON IN BELOW AFB
2. Set IF port of tuner to 38.9MHz. (Use a pattern generator). 3. Input a color bar pattern (PAL-B/G system). 4. In the Factory Service Mode, select "Adjustment VCO" and set VCO data to 63. 5. Ensure "SD On" (Signal Input) and "SD Off" (No Signal). 6. Adjust T201 (connected to TDA8374A pins3,4) so that AFA Bit is "INSIDE WINDOW" (the AFB Bit is above~below).
TUNER
IF (38.9MHz)
IC201 (TDA8374)
IC902
Fig. 4-6
4-18
Samsung Electronics
Alignment and Adjustments
4-3-10 RF AGC Adjustment
1. Connect a pattern generator (PM5418) RF signal to tuner RF. 2. Select a gray scale pattern and PAL-B/G system. Set to 479.25MHz. 3. Connect IC201 (ONECHIP) pin 53 to a digital multimeter. 4. Adjust AGC (using volume keys)in the Factory Service Mode. Set IC201 (ONECHIP) _ pin 54 to 3.7 + 0.05V (DC). 5. Adjust AGC within 20 seconds after power ON.
4-3-12 Geometry Adjustment
(SC PVAPVS PSL PHS) 1. Input a lion head pattern (in the PAL channel). 2. Set the SC (S-Correction) 10 data steps and PSL 20 data steps so that the lion head circle becomes oval. 3. Adjust with PVS (Vertical-shift) : Lion head pattern and mechanical centers must be aligned. 4. Adjust with PVA (Vertical-Amplitude) : Top margin of the picture is 4.
4
4-3-11 Sub-Color Adjustment
Set the SCR data steps to 15 in the Factory Mode.
Fig. 4-7 5. Adjust with PSL (Vertical-Slope) : Bottom margin of the picture is 4.
4
Fig. 4-8 6. Adjust with PHS (Horizontal Shift) : Lion head pattern and CRT centers are aligned.
5
5
Fig. 4-9 7. Adjust PHS (using the width coil) so that left and right margins of the picture are 5.
Samsung Electronics
4-19
MEMO
4-20
Samsung Electronics