Text preview for : 05-disassembly(xerox).pdf part of xerox phaser 3116 service manual xerox phaser 3116
Back to : serv manual 3116.rar | Home
Disassembly and Reassembly
5
5. Disassembly and Reassembly
5.1 General Precautions on Disassembly
Releasing Plastic Latches
Many of the parts are held in place with plastic latches. The latches break easily; release them carefully. To remove such parts, press the hook end of the latch away from the part to which it is latched.
When you disassemble and reassemble components, you must use extreme caution. The close proximity of cables to moving parts makes proper routing a must. If components are removed, any cables disturbed by the procedure must be restored as close as possible to their original positions. Before removing any component from the machine, note the cable routing that will be affected.
Whenever servicing the machine, you must perform as follows:
1. Check to verify that documents are not stored in memory. 2. Be sure to remove the toner cartridge before you disassemble parts. 3. Unplug the power cord. 4. Use a flat and clean surface. 5. Replace only with authorized components. 6. Do not excessive force on components made of plastic, they may break. 7. Make sure all components are in their proper position.
Service Manual
5-1
Disassembly and Reassembly
5.2 Top Cover
1. Pull the Cassette out of the printer. 4. Unlatch the front ends of the Top Cover.
Cassette
2. Remove the Front Cover in the direction of arrow.
5. Remove the Top Cover in the direction of arrow.
Top Cover
Front Cover
3. Remove four screws.
6. Remove the Rear Cover from the Top Cover.
Rear Cover
5-2
Service Manual
Disassembly and Reassembly
5.3 Fuser (Heat Lamp Type)
1. Before you remove the Fuser, you should remove: - Top Cover (see page 5-2) - Power Supply Cover (see 5.8 Engine Shield Ass'y) 2. Unplug two connectors from the boards, then remove four screws. 5. Remove one screw and take the Idle Gear out.
Idle Gear
Fuser Ass'y
6. Remove four screws and divide the Fuser into two parts
Fuser Cover
3. Remove two screws and take the Thermostat out of the Fuser.
Thermostat
7. Remove the Thermister from the Fuser Cover. 4. Remove two screws and take the Halogen Lamp out of the Heat Roller.
Heat Roller
Thermister
Halogen Lamp
Service Manual
5-3
Disassembly and Reassembly
5.4 Exit Roller
1. Before you remove the Exit Roller, you should remove: - Top Cover (see page 5-2) 2.Remove the Exit Gear, Bearing and Exit Roller as shown to the right
1 2 Exit Gear Bearing Exit Roller
5.5 LSU
1. Before you remove the LSU, you should remove: - Top Cover (see page 5-2) 2. Remove two screws and unplug one connector from the Frame. 4. Unplug two connectors from the LSU
5. Unplug four screws and take the LSU out.
LSU
3. Remove the LED PBA Ass'y as shown below.
LED PBA Cover
5-4
Service Manual
Disassembly and Reassembly
5.6 Fan
1. Before you remove the Fan, you should remove: - Top Cover (see page 5-2) 2. Unplug the connector from the SMPS and remove the one screw. Then take out the Fan.
DC Fan
5.7 Drive Ass'y
1. Before you remove the Drive Ass'y, you should remove: - Top Cover (see page 5-2) 2. Remove six screws from the Drive Ass'y. 3. Unplug one connector from the Drive Ass'y
Drive Ass'y
Caution : The six screws have numbers stamped into the Drive Ass'y base plate. When refitting the Drive Ass'y tighten the screws the order they are numbered.
Service Manual
5-5
Disassembly and Reassembly
5.8 Engine Shield Ass'y
1. Before you remove the Engine Shield Ass'y, you should remove: - Top Cover (see page 5-2) - Power Supply Cover - Fuser Connectors (see page 5-3) 2. Remove the twelve screws securing from the Engine Shield Ass'y and unplug the all connectors. Then remove the Engine Shield Ass'y.
Power Supply Cover
Engine Shield Ass'y
5.9 Main PBA
1. Before you remove the Main PBA, you should remove: - Top Cover (see page 5-2) - Power Supply Cover - Engine Shield Ass'y (see page 5-8) 2. Unplug one connector and remove two screws from the Main PBA. Then lift the Main PBA out, as shown below.
Main PBA
Connector (CN4)
5-6
Service Manual
Disassembly and Reassembly
5.10 SMPS
1. Before you remove the SMPS, you should remove: - Top Cover (see page 5-2) - Power Supply Cover - Engine Shield Ass'y (see page 5-8) 2. Unplug one connector and remove three screws then take the Inlet Bracket out.
Inlet Bracket
3. Remove one screw and unplug one connector from the Main PBA.
4. Remove three screws and take the SMPS out.
SMPS
Service Manual
5-7
Disassembly and Reassembly
5.11 Transfer Roller
1. Before you remove the Transfer Roller, you should remove: - Top Cover (see page 5-2) - LSU (see page 5-6) 2. Remove three screws and take the Transfer Earth out. 3. Unplug the PTL Holder Connector, then remove the PTL Holder and PTL Lens, as shown below.
PTL Holder PTL Lens
Transfer Earth
4. Unlatch the Bush and remove it. Then lift the Transfer Roller out, as shown below.
Transfer Roller Bush
5-8
Service Manual
Disassembly and Reassembly
5.12 Feed Roller
1. Before you remove the Feed Roller, you should remove: - Top Cover (see page 5-2) - Drive Ass'y (see page 5-7) 2. Remove two screws from the Guide Paper and take it out.
Guide paper
5. Remove the Idle Gear and Feed Gear2.
Feed Gear2
Idle Gear
6. Remove the Feed Gear 1 Ass'y, as shown below.
3. Pull up the Feed Idle Bush and Feed Idle Shaft, as shown below.
Feed Idle Shaft Bush
Feed Gear1 Ass'y
7. Remove the Feed Roller and Feed Roller 1, as shown below. 4. Remove three screws from the Feed Bracket and take it out.
Feed Bracket Feed Roller
Feed Roller1
Service Manual
5-9
Disassembly and Reassembly
5.13 Pick Up Roller & Solenoid
1. Before you remove the Pick up Roller, you should remove: - Top Cover (see page 5-2) - Drive Ass'y (see page 5-7) - Engine Shield Ass'y (see page 5-8) 2. Remove three screws from the Feed Bracket and take it out.
Feed Bracket Bush
4. Remove the Pick up Ass'y, as shown below.
1 2
Pick up Ass'y
5. Remove two screws then remove the Manual Solenoid and Pick Up Solenoid. 3. Remove the Pick up Gear Ass'y, as shown below.
Pick up Gear Ass'y (Pick up) Solenoid (Manual) Solenoid
5-10
Service Manual