Text preview for : Chassis E9 Komplett.pdf part of Universum FT-4201 EVELUX E9A, Universum FT-4201.
Back to : Chassis E9 Komplett.rar | Home
Chassis E9-service manual
V/2000 436551
CHASSIS E9 SERVICE MANUAL
· ·
Page TECHNICAL SPECIFICATIONS TV SETS WITS CHASSIS E9............................2 MODULES ARRANGEMENT ON CHASSIS........................................................4
GENERAL INSTRUCTIONS..........................................................5 X-RAY RADIATION..............................................................................................5 SAFETY................................................................................................................5 MEASUREMENT CONDITIONS.................................................................................6 · BLOCK DIAGRAM AND OPTIONS TABLES......................................................7 · BLOCK DIAGRAM CONTROL SIGNALS...............................................8 · BLOCK DIAGRAM - SUPPLY VOLTAGES.........................................................9 · SERVICE ADJUSTMENTS OF THE COLOUR TV WITH E9 CHASSIS.................10 · ELECTRICAL DIAGRAM OF MAIN CHASSIS E9..............................................23 · ELECTRICAL DIAGRAM OF MODULES FOR CHASSIS E9...............................24 · OSCILLOGRAMS...........................................................................................25 · MAIN CHASSIS - COMPONENT SIDE..............................................................26 · ELECTRICAL DIAGRAMS OF SEPARATE MODULES FOR CHASSIS E9..........27 · COMPONENT LOCATIONS ON SEPARATE MODULES OF CHASSIS E9 COMPONENT SIDE ......................................................................................29 · LIST OF RECOMMENDED SPARE PARTS FOR CHASSIS AND MODULES .......34
·
1
Chassis E9-service manual
E9 CHASSIS - TECHNICAL SPECIFICATION Rev.11
TVTEXT Version 1p (SDA5252-2)
1. SCREEN SIZE: 90° or 110°, 14",20",21", 25", 28", 33" (4:3). 2. AVAILABLE · PAL BG, STANDARDS: · PAL I,H (opt.), · PAL/SECAM BG (opt.), · PAL/SECAM BG / DK (opt.), · NTSC through SCART (opt.), · SECAM L/L' (opt.). HYPERBAND: VHF 2-12, 3. TUNER: UHF 21-69, S1-S41 Frequency synt. (125KHz 4. FEATURES: search steps), MENU oriented OSD (On Screen Disp.) 100 programs, Full function remote control, Automatic switch off at the end of the progr. Off timer 0 - 120 min., Organise Program Information System (OPIS) with the following functions: · Autostore · Insert · Delete · Rename, Hotel mode (opt.).
TVTEXT Version 7p (SDA 5255-2)
90° or 110°, 21", 25", 28", 33" (4:3), 28", 32" (16:9). · PAL BG, · PAL I,H (opt.), · PAL/SECAM BG (opt.), · PAL/SECAM BG / DK (opt.), · NTSC through SCART (opt.), · SECAM L/L' (opt.). HYPERBAND: VHF 2-12, UHF 21-69, S1-S41 Frequency synt. (125KHz search steps), MENU oriented OSD (On Screen Disp.) Multilanguage MENU OSD, 100 programs, Full function remote control, Automatic switch off at the end of the progr. Off timer 0 - 120 min., Organise Program Information System (OPIS) with the following functions: · Autostore with simple ATS: Autostore, Name, Order, · Insert · Delete · Rename, Copy funct. SCART2 to SCART1 (opt.), Hotel mode (opt). MONO/STEREO/DUAL sound decoder, Digital Stereo Sound Processor, Muting, 1 or 2 loudspeakers, Audio music power: 1x15W (MONO), 2x15W (STEREO), Additional 2 tweeter loudspeakers (opt.), Built in additional Subwoofer loudspeaker with 30W music power (Cabinet opt.), STEREO through SCART (opt.), German STEREO + NICAM (opt.), Automatic volume levelling (opt.),
TVTEXT Version Dolby 7p (OTP)
90° or 110°, 21", 25", 28", 33" (4:3), 28", 32" (16:9). · PAL BG, · PAL I,H (opt.), · PAL/SECAM BG (opt.), · PAL/SECAM BG / DK (opt.), · NTSC through SCART (opt.), · SECAM L/L' (opt.). HYPERBAND: VHF 2-12, UHF 21-69, S1-S41 Frequency synt. (125KHz search steps), MENU oriented OSD (On Screen Disp.) Multilanguage MENU OSD, 100 programs, Full function remote control, Automatic switch off at the end of the program Off timer 0 - 120 min., Organise Program Information System (OPIS) with the following functions: · Autostore with simple ATS: Autostore, Name, Order, · Insert · Delete · Rename, Copy function SCART2 to SCART1 (opt.), Hotel mode (opt.). Dolby Surround Pro-Logic sound , MONO/STEREO/DUAL sound decoder, Digital Stereo Sound Processor, Muting, 2 loudspeakers, Additional 2 tweeter speakers (opt.), Built in additional Subwoofer loudspeaker (Cabinet opt.), Audio music power: 60W (15W Left, 15W Right 15W Centre, 15W Surround) German STEREO + NICAM (opt.), Automatic volume levelling (opt), Separate volume adj. on Headphones.
5. SOUND:
MONO/STEREO/DUAL sound decoder, Digital Stereo Sound Processor, Muting, 1 or 2 loudspeakers (STEREO), Audio music power output: 1x15W (MONO), 2x15W (STEREO), STEREO through SCART (opt.), German STEREO + NICAM (opt.),
2
Chassis E9-service manual
Separate volume adj. on Headph.s (opt.).
TVTEXT Version 1p (SDA5252-2)
1 - page TTX with P26, Westeuropean and easteuropean language support. SCART I AV connector 7. CONNECTIONS: (21 - pin) video, RGB, SVHS, HeadPhones Socket (opt.), Antenna connection 75 ohms unbalanced. 6. TELETEXT:
TVTEXT Version 7p (SDA 5255-2)
7 - page TTX with the TOP (opt.), FLOF and P26, Westeuropean and easteuropean language support. SCART I AV connector (21 - pin) video, RGB and SVHS, HeadPhones Socket (opt.), SCART II (opt.), MINI DIN SVHS connector with chinch AV inputs (opt.), front or backside AV - cabinet dependent, External speakers connectors (opt.), Antenna connection 75 ohms unbalanced, 1TPIP - 1 tuner picture in picture (opt.), 2TPIP - 2 tuner picture in picture (opt.) with the sound on the headphones from 2nd tuner source. Black and Blue stretch, Blue back when no video, Automatic Colour limiting, Colour Temperature adjustment, CTI (opt.), ZOOM (4:3), Linear picture zoom (16:9). 65W for 90° 95W for 110° POWER REQUIREMENTS: Voltage/frequency: 230V/50Hz rating (180V - 250V)
TVTEXT Version Dolby 7p (OTP)
7 - page TTX with the TOP (opt.), FLOF and P26, Westeuropean and easteuropean language support. SCART I AV connector (21 - pin) video, RGB and SVHS, HeadPhones Socket (opt.), SCART II (opt.), External speakers connectors (Front L and R, Rear L and R MINI DIN SVHS connector with AV chinch inputs (opt.), front or backside AV - cabinet dependent, Antenna connection 75 ohms unbalanced. 1TPIP - 1 tuner picture in picture (opt.), 2TPIP - 2 tuner picture in picture (opt.) with the sound on the headphones from 2nd tuner source. Black and Blue stretch, Blue back when no video, Automatic Colour limiting, Colour Temperature adjustment, CTI (opt.), ZOOM (4:3), Linear picture zoom (16:9). 65W for 90° 95W for 110° POWER REQUIREMENTS: Voltage/frequency: 230V/50Hz Rating (180V - 250V)
8. ADDITIONAL OPTIONS
1TPIP - 1 tuner picture in picture (opt.),
9.VIDEO:
Black and Blue stretch, Blue back when no video, Automatic Colour limiting, CTI (opt.), ZOOM.
10. 65W for 90° CONSUMPTION: 95W for 110° POWER REQUIREMENTS: Voltage/frequency: 230V/50Hz rating (180V 250V) 24.12.1999
3
MODULES ARRANGEMENT ON CHASSIS
12.12.1999
4
Chassis E9-service manual GENERAL INSTRUCTIONS
X-RAY RADIATION Picture tube is potential source of X-radiation of colour TV. Use exclusively original types of replacement picture tubes, specified in technical documentation. Accelerating high voltage must not exceed 30 kV. Supply voltage "B+" for horizontal output stage must be set according to the specifications given in service manual. SAFETY INSTRUCTIONS Service interventions on colour TV can be performed by authorised and qualified personnel only, considering the following instructions: · During service interventions connect the TV set to mains voltage through separating (isolating) transformer. · During servicing procedures (replacement of individual components) disconnect the cord from mains connector. · After disconnection and before servicing wait about 30 sec. so that charged electrolytes and picture tube are discharged. · Provide for additional discharge of picture tube when replacing it and use protective means to prevent injuries due to eventually broken glass. · When changing modules or complete chassis, fix it with adequate elements (screws, latches, ...). · Wires inside the TV set should not come in contact with sharp or hot areas. · Integrated circuits and other semiconductors on chassis are sensitive to overvoltages and high temperatures. During service interventions they should be protected against too long heating with soldering iron (5 sec.), electrostatic discharges, short circuits between connectors etc. Therefore the following general instructions should be followed: · Use low impedance disconnecting transformer for connection of chassis to mains voltage. · Use low voltage soldering irons with protective earthing. · Chassis earthing should be equal to earthing of measuring and calibrating equipment and tools. · When connecting instruments, first connect negative connector (mass, earth) and afterwards signal connector. · Voltages to be checked should be measured with suitable instruments. Do not use "short-circuit methods" with pincets or screwdriver. · Conductors under high voltage should not be placed near semiconductors on chassis. · Installed IC's, transistors and MOSFET's are made in various semiconductor technologies (CMOS, MOS, BIMOS or bipolar technology) and are more or less sensitive to exterior effects during handling. All these elements should be handled in accordance with the requirements for electrostatic protection. If these requirements are fulfilled, you prevent formation of undesired electrostatic discharges which can destruct semiconductors or can activate destructive mechanisms, which destroy circuit during operation. Accumulated electrostatic charge is discharged through individual connectors of IC or transistor during electrostatic discharges and current runs through semiconductor structure. Considering that thicknesses of semiconductor substrate, used for IC, are very small, this current can cause damages to IC or destroy it. For the protection of circuits the currents originating from discharges should be discharged under control. This is obtained in the following ways: · Staff handling the ICs should have earthed hands by means of a suitable wire and resistor. · Working table should as well be earthed. Working surface should be made of conducting material (conducting rubber), soldering irons and all required equipment should be earthed. · Carrying and storing is permissible only in original packaging (antistatic tubes, conducting sponges). · If IC is mounted on a base, it should not be replaced under voltage.
5
Chassis E9-service manual
MEASUREMENT CONDITIONS · HF input signal in antenna: 1mV, with Philips test signal · Input video signal on SCART connector: 1 Vpp · Input audio signal on SCART connector: 500 mVeff · Brightness, contrast and colour of picture, volume of sound set to normal (near middle of scale) · Measure DC voltages with digital voltmeter with 1% precision · Measuring instrument (voltmeter or oscilloscope) connect to tuner ground during measuring on secondary side of mains (SMPS) transformer and on primary side during measuring on primary side SMPS supply circuit.
6
BLOCK DIAGRAM AND OPTIONS TABLES
SOUN PROCESSOR TYPES
SOUN STANDARD STEREO+AM(L/L') (till 2xscart) TDA 3410D STREO+NICAM nd (more like 2xscart, 2 tuner) TDA 3401 G STEREO+VIRT. DOLBY TDA 3401 STEREO (till 2x scart) TDA 3415 STEREO+NICAM (till 2xscart) TYPE TDA 3400 PCB ST/E6-E9 ST/E6-E9 ST/E6-E9 ST/E9 ST/E9
HARDWARE OPTIONS FOR PROCESSORS (IC901)
SCART 2 J910 J911 ENABLE DISABLE SECAM L J902 ENABLE DISABLE D/K J906 ENABLE DISABLE COPY OPTION (what is on AV1, or from AV2 -> J905 to AV1) ENABLE DISABLE
K104B K104C
TUNER SELECTION*:
7p only TUNER SELECTION J901 J912 SIEL ALPS TEMIC and SELTEKA TEMIC and SELTEKA *except SDA5255 A052 - only SIEL
APD-E9
K1301 K1303
DOLBY PROLOGIC
SD1
K73
Rext Lext
SUR1
K74 K51
TDA2616A
Cext SRext SLext
1p/7p
SIGNAL & DEFL. PROCESSOR SEL.
7p only TDA8840 TDA8842 TDA8843 TDA8844 90° 90° 110° 110° PAL PAL/SECAM PAL PAL/SECAM
SUB
AP-E9
K1301 K74B
DZ1
K72
Rext Lext
SL1-E9
TDA2616 NE5532
K71
E9
SAT-EU
(na poz. KD-E6)
K-1201B K-1202B K1203B
TUNER1 FL2477/84 TUNER2 FL2477/84
SAW filter TDA884X SIGNAL AND DEFL. PROCESSOR
STEREO: ST-E9,ST-E6/9 DOLBY: STD-E9 K506A K507 MONO: / MSP34XX TDA2545A DPL3519A
K508A K510A K001C
AUDIO OUT
K104A K104B
R L
KD-E6
TDA7057A
TDA9800
K-1201B K-1202B K1203B K-1201A K-1202A K1203A
K500B, K501B, K502B, K503B, K504B K500A, K501A, K502A, K503A, K504A RGB K102A V+ VGUARD K101B
S1-IN
S-VHS VIDEO AUDIO-L AUDIO-R
K91 K92A K508B K404A L,R C,Y
VK-E9: 4:3 VK-E9T: 16:9 VK-E9M: minineck
TDA6107 TDA6108
SVHS-E9
K404B K403B
R G B
TDA8540
CVBS_ext
CVBS int
K92B K92C
VERT. OUT
TDA8351 (110) TDA8356 (90)
L,R
K401B K401A
K402B K402A K1 K2 K3 K4
SFTL-E9
K104B K104C K901B
EU-E9
IC1
VIDEO SWITCH TEA2014 IC902 IC903
CVBS_SC2
MODULES VK IN PICTURE TUBES
K806B
PR- PR+
+
M
SDA5250
IC901
PIP-E9
SAA9288 TDA8310
LZZ-E9
K751 K752 K703B K703A H.DRIVE EW DRIVE H. FLY EHT COMP K704B K704A
TP-CG
PR- PR+ +
K901B
K901B K901A
SDA525X
150V 33V 24V 12V 8V 5VA 5V 15VT
K902A
K800B,K801B,K802B,K803B,K804B,K805B K800A,K801A,K802A,K803A,K804A,K805A
M
K901B
TP-E9
PR- PR+ +
POWER SUPPLY TDA4605-2 BUZ90A
OC-E9
a a R-626 b b
CVBS_SC1
HOR. OUT
K106A K105A
M
SCART 2
SCART 1
BU508A (110) BU508D (90)
230V AC
PROCESSOR & EEPROM SELECTION Text IC901 pages
SDA5252-2 B001 EV E9 1P 17 99 SDA5255 B002 EV E9 1P 19 99 SDA5255 A052 SDA5255-2 B001 EV E9 7P 27 99 SDA5255 B003 EV E9 7P 29 99 Piggy back with SDA 5250 SDA545x OTP 1p 1p 7p 7p 7p 7p 1p/7p
Picture tube Manufacturer VK-E9 (4.3) basic for 90° in 110° pict. tubes A48EAX13X01 Thomson A48EEV13X01 Thomson A51EBV13X01 Thomson A51EAL30X01 Vista A51EAL155X01 Philips A51EJJ01X01 Ekranas VK-E9T (16:9) for 16:9 pict. tubes W66EHK50X06 Panasonic W66EHK51X26 Panasonic W76EGV23X115 Videocolor W76EGX23X115 Videocolor VK-E9T1 (16:9) for 16:9 pict. tubes W76ESF031X14 Philips VK-E9M (4:3) for minineck pict. tubes A48JAN43X02 BPL A51JAR70X05 BPL
IC902
24C08 24C08 24C16 or 24C08AT
IC903 Optional no.
languaes
/ / up to 1 up to 4 / / / 24C32
10.12.1999
7
Chassis E9-service manual BLOCK DIAGRAM CONTROL SIGNALS
8
Chassis E9-service manual BLOCK DIAGRAM - SUPPLY VOLTAGES
9
Chassis E9-service manual SERVICE ADJUSTMENTS OF THE COLOUR TV WITH E9 CHASSIS
All necessary adjustments and settings are performed during manufacture of TV set and assure its correct operation when connected to the mains voltage and antenna or external video or audio signal. When TV set requires service intervention all settings should be checked and corrected, if necessary. DEMAGNETISING OF PICTURE TUBE Correctness of picture tube demagnetising is usually automatically checked. Magnetisation of picture tube is presented as one or more colour "clouds", consequently colour reproduction of the picture is not correct. Each time the TV set is switched on with mains switch, demagnetising system is activated. For correct demagnetising procedure disconnect the TV set with mains switch and leave it disconnected for about 15 minutes. Afterwards when you switch on the TV, demagnetising procedure is performed. In case distortion of colour reproduction still persists, special demagnetising coil should be used.
ADJUSTMENT
1. SUPPLY VOLTAGE FOR HORIZONTAL OUTPT STAGE »B+« · ·
ADJUSTMENT CONDITION
Connect the TV set to supply voltage 175...250VAC. Switch it on and set it by means of remote controller to AV mode of operation. Connect DC voltmeter to D-602 cathode.
ADJUSTMENT ACTIVITY AND RESULT OF SETTINGS
With P-601 potentiometer set supply voltage for horizontal output stage to: · 90° CTV: 118V ±0,2V · 110° CTV: 155V ±0,2V · 110°/16:9 CTV: 155V ±0,2V
·
SWITCHING TO SERVICE MODE
All other service settings of TV set are made in so called service mode of TV set operation. To enter this mode of operation press the keys in the following sequence: "TV", "I", and "STOP" in the period of 5 seconds from switching on the TV set to normal mode of operation. When the TV set is switched over to service mode the following status line with service parameter and parameter value appears on the screen:
SERVICE PARAM: XX VALUE: xx
The parameter to be set is selected with keys (P+/P-), and selected parameter is set with keys (volume+ /volume-). Each ) the value of preselected parameter is stored. Therefore when the last setting is time you press the key for parameter selection ( performed you must press one of the two keys once again. Values of individual parameters are expressed in hexadecimal form due to limited capacity of the memory. Values of individual parameters are variable from 0 to 3F, with the exception of parameters 11, 12 and 13 where values are changed from 0 to 7F and O1, O2, O3, O4, which have value range between 0 and FF. When setting is finished it should obligatory be concluded with "STOP" key. After a few seconds the status line disappears and service adjustment is accomplished.
NOTE: In case service adjustment is not ended in above specified mode (e.g. power supply breakdown), the adjustment should be repeated. 2. VERTICAL · To antenna connector of · With remote PICTURE TV set, which is switched controller set vertical POSITION on and operates in service position of the mode, connect VF signal picture: beginning of source with PHILIPS test dark part of the 4:3 picture. picture should be exactly in the centre · Select the following service of the screen (two setting on the screen: bright points on left SERVICE PARAM: VH VALUE: xx and right side of the 16:9 screen).
10
Chassis E9-service manual ADJUSTMENT
3. VERTICAL AMPLITUDE ON TOP PART OF SCREEN
ADJUSTMENT CONDITION
· To antenna connector of TV set, which is switched on and operates in service mode, connect VF signal source with PHILIPS test picture. · Select the following service setting on the screen:
SERVICE PARAM: VA VALUE: xx
ADJUSTMENT ACTIVITY AND RESULT OF SETTINGS
· With remote controller set vertical amplitude of picture on top, visible part of the screen. The beginning of test picture should be at the beginning of top part of the screen. With remote controller set vertical amplitude of picture on bottom part of the screen. The lower part of test picture should be at the edge of bottom part of the screen. During this setting the picture on top part of the screen should not change.
4:3
16:9 ·
4. VERTICAL AMPLITUDE ON BOTTOM PART OF SCREEN
·
·
To antenna connector of TV set, which is switched on and operates in service mode, connect VF signal source with PHILIPS test picture. Select the following service setting on the screen:
4:3
SERVICE PARAM: VS VALUE: xx
16:9
5. CORRECTION OF "S" VERTICAL PICTURE DISTORTION
· To antenna connector of TV set, which is switched on and operates in service mode, connect VF signal source with PHILIPS test picture. · Select the following service setting on the screen:
SERVICE PARAM: SC VALUE: xx
6. HORIZONTAL PICTURE POSITION
·
·
To antenna connector of TV set, which is switched on and operates in service mode, connect VF signal source with PHILIPS test picture. Select the following setting on the screen:
· With remote controller correct the picture. The distances between the two horizontal lines of test picture in the centre of the screen should be equal to the distances on top and bottom part of the screen. If after this setting vertical amplitude of picture changes, see pos. 5 and 6. · With remote controller set test picture to the centre of the screen (if necessary first widen the picture, see pos. 7).
4:3
16:9
4:3
SERVICE PARAM: HS VALUE: xx
16:9
11
Chassis E9-service manual ADJUSTMENT
HORIZONTAL AMPLITUDE OF PICTURE ADJUST ONLY AT: - 110°-4:3 16:9 7.
ADJUSTMENT CONDITION
· To antenna connector of TV set, which is switched on and operates in service mode, connect VF signal source with PHILIPS test picture. · Select the following service setting on the screen:
SERVICE PARAM: EW VALUE: xx
ADJUSTMENT ACTIVITY AND RESULT OF SETTINGS
· With remote controller set picture width. Edges of test picture should be just hidden behind the edges of the screen.
7/A. HORIZONTAL AMPLITUDE OF PICTURE FOR 90° ° ADJUST ONLY AT: - 90° 8. CORRECTION OF PICTURE HORIZONTAL PINCUSHION DISTORTION ADJUST ONLY AT: - 110°-4:3 16:9
· To antenna connector of TV set, which is switched on and operates in service mode, connect VF signal source with PHILIPS test picture. · For CTV is not necessary to be in service mode. · To antenna connector of TV set, which is switched on and operates in service mode, connect VF signal source with PHILIPS test picture. · Select the following service setting on the screen:
SERVICE PARAM: PW VALUE: xx
· With coil L702 set picture width. Edges of test picture should be just hidden behind the edges of the screen. ·
With remote controller correct the picture. On left and right side of test picture straight lines should appear (especially in the centre of the picture).
4:3
16:9 9. CORRECTION OF PICTURE HORIZONTAL PINCUSHION DISTORTION IN CORNERS OF THE SCREEN ADJUST ONLY AT: - 110°-4:3 16:9 10. CORRECTION OF PICTURE TRAPEZIUM DISTORTION ADJUST ONLY AT: - 110° -4:3 16:9 · To antenna connector of TV set, which is switched on and operates in service mode, connect VF signal source with PHILIPS test picture. · Select the following service setting on the screen:
SERVICE PARAM: CP VALUE: xx
·
With remote controller correct the picture. On left and right part of test picture straight lines should appear also in corners of the screen.
4:3
16:9 · With remote controller correct the picture. On left and right part of test picture perfectly straight and vertical lines should appear.
·
·
To antenna connector of TV set, which is switched on and operates in service mode, connect VF signal source with PHILIPS test picture. Select the following service setting on the screen:
4:3
16:9 REMARK: If after correcting pincushion and trapezoidal distortion, changes the horizontal amplitude of picture, is necessary to correct also horizontal amplitude of picture according to explanation in point 7.
SERVICE PARAM: TC VALUE: xx
12
Chassis E9-service manual ADJUSTMENT
11. HORIZONTAL AMPLITUDE FOR 16:9 PICTURE TUBES ADJUST ONLY AT: 16:9 ·
ADJUSTMENT CONDITION
To antenna connector of TV set, which is switched on and operates in service mode, connect VF signal source with PHILIPS test picture. Select the following service setting on the screen: ·
ADJUSTMENT ACTIVITY AND RESULT OF SETTINGS
With remote controller set picture width. Correct 4:3 picture geometry should be obtained.
·
SERVICE PARAM: EW VALUE: xx
12
ZOOM OF PICTURE GEOMETRY (4:3)
·
ADJUST ONLY AT: 4:3
·
To antenna connector of TV set, which is switched on and operates in service mode, connect VF signal source with PHILIPS test picture. Select the following setting:
SERVICE PARAM: X1 VALUE: xx
· Select the following setting:
SERVICE PARAM: E1 VALUE: xx
· Select the following setting:
SERVICE PARAM: S1 VALUE: xx
· Set vertical geometry of picture. The picture should expand up to first horizontal white line on test picture. · Increase horizontal amplitude of picture. The picture should be expanded up to the first vertical white line on test picture. · Set the picture to the centre of the screen (if necessary).
hatched line: expand (ZOOM) picture
12/A. »MOVIE EXPAND« GEOMETRY OF ZOOM PICTURE (16:9) REMARK: The setting enables reproduction of 4:3 picture through entire 16:9 screen (with cut off edges on top and bottom side) and "letterbox" picture without black edges. This format is also automatically selected if WSS code is present (PALplus). ADJUST ONLY AT: 16:9
·
·
To antenna connector of TV set, which is switched on and operates in service mode, connect VF signal source with 16:9 "letterbox" test picture. Select the following setting:
SERVICE PARAM: X1 VALUE: xx
· Select the following setting:
SERVICE PARAM: E1 VALUE: xx
· Select the following setting:
SERVICE PARAM: S1 VALUE: xx
· Set vertical geometry of the picture. The picture should be expanded up to the edges of the test on top and bottom side. · Set horizontal amplitude of picture. The picture should be expanded up to the edge of test. · Set position of the picture to the centre of the screen.
4:3 picture
»letterbox picture«
13
Chassis E9-service manual ADJUSTMENT
13. PIP PICTURE POSITION ON LEFT SIDE Adjust only at CTV with PIP module. ·
ADJUSTMENT CONDITION
To antenna connector of TV set, which is switched on and operates in service mode, connect VF signal source with PHILIPS test picture. Select the following setting: ·
ADJUSTMENT ACTIVITY AND RESULT OF SETTINGS
·
SERVICE PARAM: P1 VALUE: xx
With remote controller set desired PIP position of picture.
14.
PIP PICTURE POSITION ON RIGHT SIDE Adjust only at CTV with PIP module.
·
To antenna connector of TV set, which is switched on and operates in service mode, connect VF signal source with PHILIPS test picture. · With remote controller set desired PIP position of picture.
· Select the following setting:
SERVICE PARAM: P2 VALUE: xx
PIP PICTURE POSITION ON LEFT SIDE (ZOOM) Adjust only at CTV with PIP module.
15.
·
To antenna connector of TV set, which is switched on and operates in service mode, connect VF signal source with PHILIPS test picture. · With remote controller set desired position of PIP picture when picture is expanded.
· Select the following setting:
SERVICE PARAM: P3 VALUE: xx
16.
PIP PICTURE POSITION ON RIGHT SIDE (ZOOM) Adjust only at CTV with PIP module.
· To antenna connector of TV set, which is switched on and operates in service mode, connect VF signal source with PHILIPS test picture. · Select the following setting:
SERVICE PARAM: P4 VALUE: xx
·
With remote controller set desired position of PIP picture when picture is expanded..
14
Chassis E9-service manual ADJUSTMENT
17. »ZOOM1« GEOMETRY OF ZOOM PICTURE (16:9) The setting enables reproduction of 4:3 expanded picture on 16:9 screen (black edges on left and right side decrease, a part of picture at top and bottom is cut off). Setting is possible only when colour TV is configured for 16:9 picture tubes). ADJUST ONLY AT: 16:9 ·
ADJUSTMENT CONDITION
To antenna connector of TV set, which is switched on and operates in service mode, connect VF signal source with PHILIPS test picture. Select the following setting: ·
ADJUSTMENT ACTIVITY AND RESULT OF SETTINGS
·
SERVICE PARAM: X2 VALUE: xx
Set vertical geometry of picture which should be expanded up to the first horizontal white line on test picture of page. Set picture width so as to get correct 4:3 picture geometry. Set picture position in the centre of the screen.
»ZOOM1«
· Select the following setting:
SERVICE PARAM: E2 VALUE: xx
·
· Select the following setting:
SERVICE PARAM: S2 VALUE: xx
·
17/A. »ZOOM1« GEOMETRY OF ZOOM PICTURE AT 4:3 The setting enables correct reproduction of »letterbox« picture on 4:3 screen (black edges on top and bottom).
·
To antenna connector of TV set, which is switched on and operates in service mode, connect VF signal source with letterbox 16:9 test picture. Select the following setting: · Set vertical geometry of picture as long as circle get correct round form in letterbox test picture. Set picture width as long as the edges of test picture should be just hidden behind the edges of the screen. Set picture position in the centre of the screen.
·
SERVICE PARAM: X2 VALUE: xx
· Select the following setting:
SERVICE PARAM: E2 VALUE: xx
. ·
»Letterbox« on 4:3 picture tube
· Select the following setting:
SERVICE PARAM: S2 VALUE: xx
·
15
Chassis E9-service manual ADJUSTMENT
18. »ZOOM2« GEOMETRY OF ZOOM PICTURE (16:9) ·
ADJUSTMENT CONDITION
To antenna connector of TV set, which is switched on and operates in service mode, connect VF signal source with PHILIPS test picture. Select the following setting: ·
ADJUSTMENT ACTIVITY AND RESULT OF SETTINGS
The setting enables reproduction of 4:3 expanded picture on 16:9 screen (black edges on left and right side decrease, a part of top part of picture is cut off so that subtitles are visible. Setting is possible only in case the colour TV is configured for 16:9 picture tubes. ADJUST ONLY AT: 16:9
·
SERVICE PARAM: X3 VALUE: xx
Set vertical geometry of picture which should be expanded up to the first horizontal white line on test picture of page. Set picture width so as to get correct 4:3picture geometry.
»ZOOM2« (»Titled Movie Expand)
· Select the following setting:
SERVICE PARAM: E3 VALUE: xx
·
· Select the following setting:
SERVICE PARAM: S3 VALUE: xx
·
19. OPERATING THRESHOLD OF AUTOMATIC AMPLIFICATION REGULATION
·
· · ·
To antenna connector of TV set, which is set to channel 12, connect VF signal source of frequency 224,25 MHz (C12) with RF amplitude 60dB/uV (1mV/75E). Connect voltmeter, dc, on C107. Switch the TV set to service mode of operation. Select the following service setting:
Set picture position. Picture should be shifted upwards (bottom edge of picture up to bottom edge of screen). · With remote controller keep changing the value of AC setting until 7.5V±0,5V appears on voltmeter display. REMARK: If in chassis is inserted WW form of tuner (small casing), with 5V supply, set on voltmeter value 2,8V±0,1V.
SERVICE PARAM: AC VALUE: xx
20. RED COMPONENT OF WHITE
·
·
To antenna connector of TV set, which is switched on and operates in service mode, connect VF signal source with PHILIPS test picture. Select the following service setting:
· With remote controller set value: 1F: Pict. Tube Philips, Panasonic. 1F: Pict. Tube Thomson. This value is for orientation and depends of picture tube.
SERVICE PARAM: R VALUE: xx
16
Chassis E9-service manual ADJUSTMENT
21. GREEN COMPONENT OF WHITE ·
ADJUSTMENT CONDITION
To antenna connector of TV set, which is switched on and operates in service mode, connect VF signal source with PHILIPS test picture. Select the following service setting: To antenna connector of TV set, which is switched on and operates in service mode, connect VF signal source with PHILIPS test picture. Select the following service setting: With remote controller following service setting:
SERVICE PARAM: I1 VALUE: xx
ADJUSTMENT ACTIVITY AND RESULT OF SETTINGS
· With remote controller set value: 24: Pict. Tube Philips, Panasonic. 28: Pict. Tube Thomson. This value is for orientation and depends of picture tube. · With remote controller set value: 24: Pict. Tube Philips, Panasonic. 20: Pict. Tube Thomson. This value is for orientation and depends of picture tube. PAL /SECAM BG/L select the · With keys for set value changing set parameter value.
SERVICE PARAM: I1 VALUE:40
· 22. BLUE COMPONENT OF WHITE ·
SERVICE PARAM: G VALUE: xx
· 23. REFERENCE OSCILLATING CIRCUIT OF DEMODULATOR
SERVICE PARAM: B VALUE: xx
·
PAL /SECAM /L' · With remote controller following service setting:
SERVICE PARAM: I2 VALUE: 00
select
the
· With keys for set value changing set parameter value.
SERVICE PARAM: I2 VALUE: 00
PAL /SECAM /DK · With remote controller following service setting:
SERVICE PARAM: I3 VALUE: 40
select
the
· With keys for set value changing set parameter value.
SERVICE PARAM: I3 VALUE: 40
24. TIME DELAY OF LUMINANCE SIGNAL
·
· 25. MAX. VOLUME FOR HOTEL TV Setting is possible only for colour TV configured for hotel TV. 26. OPTION BYTE 1
To antenna connector of TV set, which is switched on and operates in service mode, connect VF signal source with PHILIPS test picture. Select the following setting:
· With remote controller set such delay
setting that signals of colour and black - white picture overlap.
SERVICE PARAM: YD VALUE:xx
Recommended value: D
· Select the following setting:
SERVICE PARAM: HM VALUE: xx
·
With remote controller set desired value of volume.
· Select the following setting:
SERVICE PARAM: O1 VALUE: xx
· ·
· ·
See option bytes.
27. OPTION BYTE 2
· Select the following setting:
SERVICE PARAM: O2 VALUE: xx
See option bytes. See option bytes. See option bytes.
28. OPTION BYTE 3 29. OPTION BYTE 4
· Select the following setting:
SERVICE PARAM: O3 VALUE: xx
· Select the following setting:
SERVICE PARAM: O4 VALUE: xx
17
Chassis E9-service manual ADJUSTMENT
30. VOLTAGE FOR PICTURE TUBE BEAM FOCUSING ·
ADJUSTMENT CONDITION
Switch the colour TV with STOP key on remote controller to normal mode of operation. Connect signal with Philips test picture to antenna connector. ·
ADJUSTMENT ACTIVITY AND RESULT OF SETTINGS
With potentiometer for focusing voltage adjustment on HV transformer set such value of voltage, that gives sharp picture on entire surface of the screen. Sharpness should be equal in corners and in centre of the screen.
·
31.
VOLTAGE OF SECOND GRID OF UG2 PICTURE TUBE
Required instruments: · oscilloscope, · oscilloscope probe 100:1; · Cp=2,5pF (oscilloscope setting 0,5V/div; 5ms/div: ext. actuation with vertical time basis of TV set). Procedure: · To antenna connector connect signal with Philips test picture. · With oscilloscope probe search on video output stage for the cathode of picture tube on which video signal has highest voltage level of black (oscilloscope setting: 0,5V/div; 20 us/div: int. triggering). The probe should remain connected to this cathode. · Change the setting of oscilloscope to 5ms/div and ext. Triggering with vertical time basis of TV set and on oscillogram search for measuring "ABS" impulse (automatic black point stabilisation). · To antenna connector of TV set, which is switched on and operates in service mode, connect VF signal source with PHILIPS test picture and with 1kHz modulated sound carrier.
·
With potentiometer for second grid voltage adjustment on HV transformer set such value of »ABS« pulse to voltage 130±2 V.
ABS pulse 130V 0V
32.
REFERENCE OSCILLATING CIRCUIT OF SOUND DEMODULATOR
·
Connect oscilloscope probe IC525 to connector 12.
·
Rotating the core of L521 coil set min. content of video signal.
Applies to stereo version of TV set.
18
Chassis E9-service manual OPTION BYTES
Option bytes enable programme configuration of colour TV set. Changing individual bites of a byte modifies the characteristics of TV set.
O1:
7 6 BIT 0 1 2 3 4 5 6 7 5 4 3 2 1 0 0 NTSC DISABLE BLUE BACK DISABLE DYNAMIC SCIN CORRECTION ANGLE 118º DYNAMIC SCIN CONTROL DISABLE BLUE STRATCH DISABLE BLACK STRATCH DISABLE HOTEL MODE DISABLE COMB FILTER DISABLE 1 NTSC ENABLE BLUE BACK ENABLE DYNAMIC SCIN CORRECTION ANGLE 123º DYNAMIC SCIN CONTROL ENABLE BLUE STRATCH ENABLE BLACK STRATCH ENABLE HOTEL MODE ENABLE COMB FILTER ENABLE
O2:
7 6 BIT 0 1 2 3 4 5 6 7 5 4 3 2 1 0 0 PAL I DISABLE MULTISTANDARD DISABLE (if PAL I enable - only PAL I; BG/DK if option jumper DK not insert) HBL bit DISABLE OPTION LANGUAGE DISABLE 4:3 TOP DISABLE USER SET 06 HEADPHONE MENU ENABLE 1 PAL I ENABLE MULTISTANDARD ENABLE (BG/DK- if option jumper not insert; I- if bit PAL I enable) HBL bit ENABLE OPTION LANGUAGE ENABLE 16:9 TOP ENABLE USER SET 38 HEADPHONE MENU DISABLE
O3:
7 6 BIT 0 1 2 3 4 5 6 7 5 4 3 2 1 0 1 0 CTI ENABLE CTI DISABLE WELCOME MESSAGE ENABLE WELCOME MESSAGE DISABLE MSP 3401 ENABLE MSP3401 DISABLE AUTOMATIC SWITCH ON (B SEC) 8 SEC. DELAYED SWITCH ON AVL OPTION ENABLE AVL DISABLE HBL & TXT OFF (110 chassis) HBL & TXT ON (ONLY pure TXT not in UPDATE or MIX) - 90 chassis always ON ZOOM is DISABLE (only 4:3) ZOOM is ENABLE ITALIAN CHANNELS (C13-C20) ITALIAN CHANNELS DISABLE ENABLE
19
Chassis E9-service manual O4:
7 BIT 0 1 2 3&4 6 5 4 3 2 1 0 0 LOW STANDBY DISABLE AUTO ON DISABLE ZET CORRECTION DISABLE FUNCTION SPACE effect 3D effect VIRTUAL DOLBY effect VIRTUAL DOLBY, but in MENU text 3D DK SOUND 6.5MHz and 6.25MHz bit 4 0 0 1 1 bit 3 0 1 0 1 1 LOW STANDBY ENABLE (save and read Zoom_settings at switch off and anew switch on) AUTO ON ENABLE (for automatic switch on at connection to supply voltage) ZET CORRECTION ENABLE (additional menu for setting rotation of picture) VIRTUAL OPTION
5
DK ALTERNATE SOUND 6.5Mhz and 5.74MHz (RED button in menu ADJUST switching between 6.25 in 5.74 at DK sound standard)
6 7 Option bytes are set so that besides selected option byte also hexadecimal number is set on the basis of above tables. Example: · blue back-enable · dynamic scin control enable · blue stratch enable Select option byte O1 and for items, which should be activated, set "1" (other bites are "0"). In our case is as follows:
O1:
7 0 6 0 1 5 0 4 1 3 1 2 0 A 1 1 0 0
Shaded binary number should now be converted to hexadecimal value (darker frame). Afterwards set this value. SERVICE PARAM: O1 VALUE: 1A · CAUTION: Option bytes are Factory adjusted and must NOT be changed later, because they change TV set characteristics.
20
Chassis E9-service manual
For conversion from binary to hexadecimal help us next table: BIN 0 0 0 0 0 1 0 1 1 0 1 0 1 1 1 1 0 0 0 0 0 1 0 1 1 0 1 0 1 1 1 1 HEX 0 1 2 3 4 5 6 7 8 9 A B C D E F
0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1
0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1
33. INFORMATION MENU ABOUT INTEGRIRATED CIRCUITS, CONNECTED TO I2CBUS If you press i key (info) on remote control when the TV set is in service mode, you will get on the screen information about the version of current software (e.g.: VER:E9F1.6) and devices connected on I2C bus: SERVICE VER: E9F1.6 VIDEO PR. OK TDA8843 MSP 34XX OK SDA9288 XX TUNER2 XX TDA 8540 TDA8425
WD:00 SP:FF
Video processor: MSP 34XX: SDA 9288: TUNER2: TDA 8540: TDA 8425:
Bus controlled TV processor for video and audio signal Digital stereo sound processor PIP processor Second tuner for PIP picture SVHS video matrix switch HI-FI Stereo audio processor for stereo through SCART connector
If device is installed and properly connected on I2C bus it will respond with "OK" beside the name of device, otherwise there will be "XX" on this place.
21
ELECTRICAL DIAGRAM OF MAIN CHASSIS E9
23
ELECTRICAL DIAGRAM OF MODULES FOR CHASSIS E9
24
Chassis E9-service manual OSCILLOGRAMS
25
MAIN CHASSIS COMPONENT SIDE
26
Chassis E9-service manual ELECTRICAL DIAGRAMS OF SEPARATE MODULES OF CHASSIS E9
27
Chassis E9-service manual
28
Chassis E9-service manual COMPONENT LOCATIONS ON SEPARATE MODULES OF CHASSIS E9 COMPONENT SIDE
VK-E9T1
VK-E9T
VK-E9
VK-E9M
29
Chassis E9-service manual PIP-E9
SOLDER SIDE
COMPONENT SIDE
30
Chassis E9-service manual ST-E9
S1-IN
SVHS-E9
APD-E9
AP-E9
31
Chassis E9-service manual SFTL-E9 OC-E9
TP-CG
TP-E9
LZZ-E9
32
Chassis E9-service manual STD-E6 (module Dolby surround)
ST-E6 (module stereo)
33
Chassis E9-service manual LIST OF RECOMMENDED SPARE PARTS FOR CHASSIS AND MODULES
INDEX 110 90 CODE VALUE MAIN CHASSIS 220U M400V C/EL C/EL 100U M400V C/EL PR 5,0 2U2 M350V C/EL PR 5,0 10U T250V C/EL PR 5,0 47U M160V C/EL TR 5,0 1U0 M250V C/EL TR 5,0 2U2 M250V C/K/KO/Z/2E4 * 2N2M250VAC C/MPP PR * U47 J 250V C/MPP PR * U33 J 250V C/MPP PR * U39 J 250V MODULE CAP-E9 PH1 MODULE CAP-E9 34 C/MPP PR * U68 M 250V C/PP PR * U015 J 1,6KV MODULE CAP-E9 34 C/PP PR* 7800P J 1,6KV C/PP PR* U011 J 1,6KV C/PP PR* 6800P J 1,6KV C/PP PR* 8200P J 1,6KV C/PP PR* 8500P J 1,6KV C/PP PR* U012 J 1,6KV C/PP PR* U033 K 630V C/PP PR* U015 J 1KV C/PP PR* U033 K 630V C/PP PR* U012 J 1,6KV C/PP PR15,0 220P J 1,6KV C/X2 PR* U47 M 275VAC C/X2 PR15,0 U10 M 275VAC C/X2 PR22,5 U22 M 275VAC D/SI/1N4001 TA D/SI/1N4001 TA D/SI/1N4003 TA D/SI/1N4148 TA D/SI/1N4148 TA D/SI/1N4148 TA D/SI/1N4148 TA D/SI/1N4148 TA D/SI/1N4148 TA D/SI/1N4148 TA D/SI/1N4148 TA D/SI/1N4148 TA D/SI/1N4148 TA D/SI/1N4148 TA D/SI/1N4148 TA D/SI/1N4148 TA D/SI/BAT85 TA POSITION C-9642 - // C-9709 C-9606 C-9605 C-9714 C-9202 C-9645 C-9707 - // - // - // - // C-9715 C-9711 - // - // - // - // - // - // - // C-9627 C-9713 - // - // C-9625 C-9641 C-9646 C-9636 D-9701 D-9702 D-9205 D-9104 D-9105 D-9106 D-9109 D-9601 D-9606 D-9705 D-9710 D-9902 D-9904 D-9906 D-9911 D-9912 D-9108
412499 414653 415949 338557 414794 415947 415032 412517 W, 90 414655 110, W28<< 413778 W-PH 415881 110-PH 429359 110-34« 433921 413782 W-32« 425838 110-34« 433920 90-EK 316792 110 338584 90-VC 412924 90-PH 413777 90-PH 415688 W-28« 425986 415936 W-32« 428781 110 415936 W-28« 425986 415937 429609 429610 429611 313551 313551 300874 51666 51666 51666 51666 51666 51666 51666 51666 51666 51666 51666 51666 51666 412464
5,0 5,0 5,0 5,0 5,0
22,5
22,5
15,0 15,0 22,5 12,5 12,5 12,5 10,0 10,0 10,0 12,5 12,5 12,5 12,5 12,5 10,0 10,0 10,0 12,5 12,5 17,5
34
Chassis E9-service manual
INDEX CODE 324669 410680 410680 410680 410680 410680 410680 424580 424580 424580 424580 424580 424279 415931 415931 415931 415931 417320 417320 68571 325626 304326 416865 416961 429960 415922 415922 322956 415923 430695 415921 419821 425757 425758 427444 427442 427443 427445 366430 423189 431379 426141 426141 423429 423427 424019 424019 423988 423989 VALUE MAIN CHASSIS TA TA TA TA TA TA TA POSITION D-9706 D-9708 D-9605 D-9605 D-9607 D-9609 D-9614 D-9302 D-9604 D-9703 D-9704 D-9709 D-9608 D-9610 D-9611 D-9612 D-9613 D-9602 D-9707 D-9711 D-9910 D-9603 DU-9602 - // IC-9902 IC-9602 IC-9604 IC-9605 IC-9603 IC-9901 IC-9601 IC-9102 IC-9301 - // IC-9101 - // - // - // IC-9104 TUN-9102 K-9102A K-9901A K-9103A K-9701 K-9001A K-9301A K-9702A K-9104A 20,0/H10 20,0/H10 15,0/H10 15,0/H10 15,0/H10 15,0/H10 15,0/H10 12,5 12,5 12,5 12,5 12,5 12,5 12,5 12,5 12,5 12,5 15,0/H10 15,0/H5 10,0 10,0 12,5
110 90
110 90 110-P 90-P 90-PS 110-PS
EURO
D/SI/BY228 D/SI/BY399 D/SI/BY399 D/SI/BY399 D/SI/BY399 D/SI/BY399 D/SI/BY399 D/SI/BYT52G D/SI/BYT52G D/SI/BYT52G D/SI/BYT52G D/SI/BYT52G D/SI/BYT52M TA D/SI/BYW54 TA D/SI/BYW54 TA D/SI/BYW54 TA D/SI/BYW54 TA D/SI/BYW76 TA D/SI/BYW76 TA DIODE Z/ 2,7V/C/0,5W DIODE Z/ 3,9V/C/0,5W TA DIODE Z/33 V/C/0,5W TA MAINS CHOKE 2X70 MH MAINS CHOKE 2X33 MH IC AT24C08-10 PC IC LM317T IC LM317T IC MC7805CT IC MC7808T IC SDA545XOTP-B 13 IC TDA4605-2 IC TDA7057AQ IC TDA8351 IC TDA8356/N5 IC TDA8843/N2C IC TDA8840/N2C IC TDA8842/N2C IC TDA8844/N2C IC VIDEO SWITCH TUNER FDL2473/84A TUNER EL2787-84 CONNECTOR M / 7/2,5 90647-1007 CONNECTOR M / 7/2,5 90647-1007 CONNECTOR M/ / 2/2,5 MKS1951 CONNECTOR M/ / 4/2,5 MKS1954 CONNECTOR M/ 3/2,5 90647-1003 CONNECTOR M/ 3/2,5 90647-1003 CONNECTOR M/4/2,5 90647-1004 CONNECTOR M/ 5/2,5 90647-1005
35
Chassis E9-service manual
INDEX CODE 319045 431081 316831 316831 316831 421055 79039 420919 410208 410208 338708 410208 68503 68503 419741 338569 415965 68152 52777 372123 372123 372123 372123 372123 421131 421131 411567 415009 411572 411574 411574 419823 330380 330380 313601 429553 419824 419824 419825 416940 433776 316701 420920 420920 429521 419822 416508 415953 415952 VALUE MAIN CHASSIS CRYSTAL 4,4 MHz CRYSTAL 6 MHz FUSE HOLDER FUSE HOLDER FUSE HOLDER METAL SHIELD E6/E7 PASTE SILICON P12 WASHER CRT B10-301ST 0330770023 MICA WASHER MICA WASHER MICA WASHER MICA WASHER IC SOCKET 8 IC SOCKET 8 R/NTC B57234-S709-M R/PL TA R47 J 0,5 W R/PL TA 5K1 J 0,33 W R/PL TA 100K J 0,25 W R/PL TA 120K J 0,25 W R/PL/VR TA 2R2 J 0,33W R/PL/VR TA 2R2 J 0,33W R/PL/VR TA 2R2 J 0,33W R/PL/VR TA 2R2 J 0,33W R/PL/VR TA 2R2 J 0,33W R/PL/VR TA 47R J 0,33W R/PL/VR TA 47R J 0,33W R/PL/VR TA 120R J 0,75W R/PL/VR/NG TA 1K0 J 0,5 W R/PL/VR/VT TA R15 K 0,75W R/PL/VR/VT TA R22 K 0,4 W R/PL/VR/VT TA R22 K 0,4 W R/PLK 0204 TA 2K05 F 0,25 W R/PLK 0204 TA 3K F 0,25 W R/PLK 0204 TA 3K F 0,25 W R/PLK 0204 TA 10K F 0,25 W R/PLK 0204 TA 39K F 0,25 W R/PLK 0204 TA 243R F 0,25 W R/PLK 0204 TA 243R F 0,25 W R/PLK 0204 TA 715R F 0,25 W R/PLK/VN TA 220K J 1 kV R/PLK/VN TA 820K J 1,6KV R/PLKO TA R82 J 1W R/PLKO TA 1R0 J 1W R/PLKO TA 1R0 J 1W R/PLKO TA 2R7 J 4W R/PLKO TA 10R J 2W R/PLKO TA 22K J 2W R/PLKO TA 27K K 6W R/PLKO TA 47K J 1,5W POSITION Q-9101 Q-9901 FOR VA-9601 FOR VA-9602 FOR VA-9603 MP-9101 FOR HEATSINK 318695 PD-9201 FOR IC-9602 FOR IC-9604 FOR T-9602 FOR T-9705 FOR IC-9902 FOR IC-9903 R-9629 R-9703 15,0 R-9610 10,0 R-9615 IN SER. W. R120K R-9615 IN SER. W. R100K R-9121 15,0/H10 R-9156 15,0/H10 R-9715 15,0/H10 R-9953 12,5 R-9977 12,5 R-9304 15,0/H10 R-9609 15,0/H10 R-9210 20,0/H10 R-9707 15,0/H10 R-9622 15,0/H10 R-9710 15,0/H15 R-9713 15,0/H15 R-9618 12,5 R-9118 10,0 R-9308 12,5 R-9909 10,0 R-9122 12,5 R-9616 12,5 R-9623 12,5 R-9625 12,5 R-9701 12,5 R-9613 12,5 R-9702 15,0 R-9207 15,0/H10 R-9306 20,0/H10 R-9714 20,0/H15 R-9725 20,0/H20 R-9603 20,0/H15 R-9624 35,0/H20 R-9606 20,0/H10
36
Chassis E9-service manual
INDEX CODE 429522 417319 430531 338709 338709 338709 338709 338709 338709 422699 423137 338580 411262 411262 411262 411262 411262 411262 411262 411262 411262 411262 411262 411262 411262 415900 413787 415928 415928 411261 411261 411261 411261 414036 420389 425763 425764 427975 425765 425766 378773 339150 413801 429470 429703 433863 427974 21108 21108 VALUE MAIN CHASSIS R/PLKO TA 75K J 4 W R/PLKO TA 120R K4 W R/PTC 16:9 T209 CLIP IC CLIP IC CLIP IC CLIP IC CLIP IC CLIP IC CLIP IC T/FET/BUZ90A T/NPN/AF/BC639 TR T/NPN/BC547B TR T/NPN/BC547B TR T/NPN/BC547B TR T/NPN/BC547B TR T/NPN/BC547B TR T/NPN/BC547B TR T/NPN/BC547B TR T/NPN/BC547B TR T/NPN/BC547B TR T/NPN/BC547B TR T/NPN/BC547B TR T/NPN/BC547B TR T/NPN/BC547B TR T/NPN/BU508AF T/NPN/BU508D/BU508DF/BU508DR T/NPN/PH2369 TR T/NPN/PH2369 TR T/PNP/BC212B/BC557B TR T/PNP/BC212B/BC557B TR T/PNP/BC212B/BC557B TR T/PNP/BC212B/BC557B TR T/PNP/BD242 TRANSFORM. SMPS E6 TRANSFORM. SMPS E9 110 TRANSFORM. SMPS E9 90 TRANSFORM.HV E9 16:9 TRANSFORM.HV E9 TRANSFORM.HV E9 90 TRANSFORM. DRIVER G2/E5 LINEARITY COIL 12-25 LINEARITY COIL G4/E5 LINEARITY COIL EKM 12-126 LINEARITY COIL EKM 12-127 LINEARITY COIL EKM 12-134 COIL EW E9 FUSE T 1,25 A L 250V FUSE T 1,25 A L 250V POSITION R-9604 20,0/H15 R-9305 20,0/1-110 R-9628 FOR IC-9102 FOR IC-9301 FOR IC-9602 FOR IC-9604 FOR T-9602 FOR T-9701 FOR T-9705 T-9602 T-9703 T-9104 T-9105 T-9106 T-9108 T-9601 T-9603 T-9702 T-9706 T-9902 T-9904 T-9905 T-9906 T-9908 T-9701 - // T-9109 T-9903 T-9107 T-9110 T-9704 T-9911 T-9705 TR-9601 - // - // TR-9701 - // - // TR-9702 L-9701 - // - // - // - // L-9703 VA-9601 VA-9602
110, W 90
D, SW ST 90 W 110 90 110 90 W-32« W-28« 110-34«
37
Chassis E9-service manual
INDEX CODE 431998 427639 428383 429975 430836 VALUE MAIN CHASSIS FUSE T2A E 250V MODULES MODULE KD-E6/9 MODULE SVHS-E9 MODULE APD-E9 MODULE STD-E6/9 II MODULE ST E-6/9 MODULE ST E-9 MODULE PIP2 E9/1 S2 MODULE LZZ-E9/1 MODULE KD FILTER CER.SFE 5,5 MHz 5,5MC FILTER CER.TRAP TPS 5,5 MB FILTER OFW G 1968 IC TDA9800 TUNER FL 2477/84 CONNECTOR Z/32/ 3/2,54 CONNECTOR Z/32/ 4/2,54 REFEREN. COIL 77,8MHZ CONTACT HEADER / 2/2,5 P/PL/NA/LIN/V 25K 0,05W T/NPN/BC547B TR T/NPN/BC547B TR T/PNP/BC212B/BC557B TR MODULE SVHS IC TDA8540 CONNECTOR Z/32/13/2,54 CONNECTOR Z/32/ 5/2,54 CONNECTOR M/ / 3/2,5 MKS2953 STERO MODULE DIODE Z/ 8,2V/C/0,5W TA IC DPL3519A IC MSP3400 IC MSP3410D IC MSP3401G IC TDA2545A IC TDA4445B IC TDA7050 CONNECTOR Z/ /3/2,5 CONNECTOR Z/32/ 4/2,54 CONNECTOR Z/32/ 5/2,54 CONNECTOR Z/32/11/2,54 CONNECTOR M/ / 3/2,5 MKS2953 CONNECTOR M/ / 3/2,5 MKS2953 CONNECTOR M/ / 7/2,5 MKS2957 CONNECTOR M/ 3/2,5 90649-1003 CRYSTAL 18,432MHZ 4730006848 REFEREN. COIL 38,9MHZ KZS-73 POSITION VA-9603 K-1201 - K-1203 K-401 - K402 K-001 K-500 - K-504 - // - // K-800 - K-805 K-703, K-704
D D ST
433983 431365
52819 413802 419135 423180 416507 420732 420735 423179 413792 51900 411262 411262 411261 419731 427631 420734 423419 419734 425590 420187 425622 433927 378782 422733 419728 338638 420735 420734 420736 423419 423419 423417 423991 420188 424135
Q-1204 Q-1202 F-1201 IC-1201 TUN-1201 K-1202B K-1201 B L-1201 K-1203B P-1201 T-1201 T-1203 T-1202 IC-401 K-401 B K-402B K-404B D-521 12,5 IC-523 IC-521 - // - // IC-523 IC-524 IC-522 K-506B K-501 B K-504B K-502B K-506A K-508A K-507A K-51 OA Q-521 L-521
D D N
38
Chassis E9-service manual
INDEX CODE 413792 414955 411262 411262 411262 419754 419736 330418 338577 411262 424406 423425 424019 338709 411262 415949 427971 414037 51666 51666 51666 424580 415923 423987 415009 419485 419485 314862 431359 412710 412710 412710 51666 51666 412464 420773 425756 366430 427630 420732 420734 420734 427631 423418 319045 420070 VALUE CONTACT HEADER 2/2,5 R/PL/VR/VT TA 10R K 0,4 W T/NPN/BC547B TR T/NPN/BC547B TR T/NPN/BC547B TR MODULE OC DIODE Z/130 V/C/2W TA IC SFH617 P/PL/NA/LIN/H 1K 0,05W R/PLK/VN TA 10M K 10 kV T/NPN/BC547B TR MODULE AP IC TDA2616Q CONNECTOR M/ / 7/2,5 MKS1957 CONNECTOR M/ 3/2,5 90647-1003 CLIP IC T/NPN/BC547B TR MODULE LZZ C/EL PR 5,0 2U2 M350V C/MPP PR22,5 1U0 J 400V C/PP PR * 2200P J 1,6KV D/SI/1N4148 TA D/SI/1N4148 TA D/SI/1N4148 TA D/SI/BYT52G IC MC7808T CONNECTOR M/ 2/2,5 90647-1002 R/PL/VR/NG TA 1 KO J 0,5 W T/NPN/337 T/NPN/337 T/PNP/BC327 BRIDGE COIL E9/2 MODULE PIP C/ELB TR 5,0 10U M 40V C/ELB TR 5,0 10U M 40V C/ELB TR 5,0 10U M 40V D/SI/1N4148 TA D/SI/1N4148 TA D/SI/BAT85 TA IC SDA9288 IC TDA8310A IC VIDEO SWITCH CONNECTOR Z/32/ 2/2,54 CONNECTOR Z/32/ 3/2,54 CONNECTOR Z/32/ 5/2,54 CONNECTOR Z/32/ 5/2,54 CONNECTOR Z/32/13/2,54 CONNECTOR M/ / 4/2,5 MKS2954 CRYSTAL 4,4 MHz CRYSTAL 20,48MHZ POSITION K-503B R-555 T-523 T-524 T-525 D-661 IC-661 P-661 R-665 T-661 12,5
12,5
22,5
IC-91302 K-91301 K-91303 FOR IC-91302 T-91301 C-9752 C-9751 C-9753 D-9752 D-9753 D-9754 D-9751 IC-9751 K-9751 R-9751 T-9751 T-9753 T-9752 L-9751 C-9834 C-9845 C-9846 D-9800 D-9802 D-9801 IC-9802 IC-9801 IC-9803 K-9803A K-9801 B K-9802B K-9805B K-9804B K-9806B Q-9801 Q-9802 5,0 22,5 12,5 12,5 12,5 15,0/H10
15,0/H10
5,0 5,0 5,0 12,5 12,5 12,5
39
Chassis E9-service manual INDEX CODE 413792 426647 420581 420580 420580 426571 372123 372123 415206 415206 415206 415206 415206 415206 427809 411261 414025 VALUE CONTACT HEADER / 2/2,5 CONTACT HEADER 36/ 2/2,54 CONTACT HEADER 36/ 3/2,54 CONTACT HEADER 36/ 5/2,54 CONTACT HEADER 36/ 5/2,54 CONTACT HEADER 36/13/2,54 R/PL/VR TA 2R2 J 0,33W R/PL/VR TA 2R2 J 0,33W T/NPN/SMD BC847B T T/NPN/SMD BC847B T T/NPN/SMD BC847B T T/NPN/SMD BC847B T T/NPN/SMD BC847B T T/NPN/SMD BC847B T T/NPN/SMD PMBT2369 T/PNP/BC212B/BC557B TR T/PNP/SMD BC857 T POSITION K-9800B K-9803A K-9801A K-9802A K-9805A K-9804A R-9817 10,0/H10 R-9826 12,5 T-9801 T-9807 T-9808 T-9810 T-9811 T-9812 T-9804 T-9809 T-9806
LEGEND:
110............110 picture tube W..............16:9 picture tube PH............. PHILIPS D............... DOLBY SW............ SUBWOOFER
90..............90 picture tube W-28«.........28<<, 16:9 picture tube EK.............. EKRANAS S............... STEREO
40
Chassis E9-service manual
NOTES:
41