Text preview for : CDP-C160Z.pdf part of Sony CDP-C160Z Entire service manual
Back to : CDP-C160Z.pdf | Home
CDP-C160Z/C260Z/CE215/CE315
SERVICE MANUAL
US Model
CDP-C160Z/C260Z/CE215/CE315
Canadian Model
CDP-C260Z/CE215/CE315
AEP Model Australian Model
CDP-CE215/CE315
UK Model E Model
CDP-CE315
Photo : CDP-CE315
Model Name Using Similar Mechanism CD Mechanism Type Base Unit Type Optical Pick-up Type
CDP-C250Z/C350Z/CE305/CE405 CDM27A2-5BD20 BU-5BD20 KSS-213BA/F-NP
SPECIFICATIONS
Compact Disc Player Laser Semiconductor laser ( = 780 nm) Emission duration: continuous Laser output Max 44.6 µW* * This output is the value measured at a distance of 200 mm from the objective lens surface on the Optical Pick-up block with 7 mm aperture. Frequency response 2 Hz to 20 kHz ± 0.5 dB Signal-to-noise ratio More than 102 dB Dynamic range More the 98 dB Harmonic distortion Less than 0.0045% General Power requirements Where purchased US, Canadian Power requirements 120V AC, 60 Hz
AEP, UK, CIS, Singapore 220-230V AC, 50/60 Hz North European, East European Australian E 240V AC, 50/60 Hz 110-120V, 220-240V adjustable, 50/60 Hz 14W 430 × 120 × 385 mm (17 × 4 3/4 × 15 1/4 in.) incl. projecting parts 5.4 kg (11 lbs 15 oz)
Power consumption Dimensions (approx.) (w/h/d) Mass (approx.)
Output Jack type LINE OUT Phono jacks Maximum output level Load impedance Supplied accessories Audio cord (2 phono plugs2 phono plugs) (1) Remote commander (remote) (CDP-CE315 and CDP-C260Z only) Sony SUM-3 (NS) batteries (2) (CDP-CE315 and CDP-C260Z only) Design and specifications are subject to change without notice.
2V Over 10 kilohms (at 50 kilohms) 18 dBm Wave length: 660nm
DIGITAL OUT Optical (OPTICAL) output (AEP,UK,CIS, connector North European, East European models only)
COMPACT DISC PLAYER
MICROFILM
The following caution label is located inside of the unit.
1. 2.
2-1. 2-2. 2-3. 2-4. This appliance is classified as a CLASS 1 LASER product. The CLASS 1 LASER PRODUCT MARKING is located on the rear exterior.
TABLE OF CONTENTS GENERAL ..................................................................... 5 DISASSEMBLY
Case, Bottom Plate and Front Panel ··································· 6 Back Panel and Disc Table ················································· 6 Optical Pick-up Block Assembly ······································· 7 Bracket (Gear) Assembly ··················································· 7
3. 4.
4-1. 4-2. 4-3. 4-4. 4-5. 4-6. 4-7. 4-8. 4-9
ELECTRICAL BLOCK CHECKING ..................... 8 DIAGRAMS
Circuit Boards Location ··················································· 10 Printed Wiring Board -- BD Section -- ·························· 11 Schematic Diagram -- BD Section -- ····························· 13 Printed Wiring Board -- Main Section -- ······················· 15 Schematic Diagram -- Main Section -- ·························· 17 Schematic Diagram -- Display Section -- ······················ 19 Printed Wiring Board -- Display Section -- ··················· 21 IC Block Diagrams ··························································· 23 IC Pin Functions · IC101 Digital Signal Processor (CXD2545Q) ··············· 25 · IC302 System Control (CXP82324-082Q) ···················· 28
CAUTION
Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.
5.
5-1. 5-2. 5-3. 5-4.
EXPLODED VIEWS
Front Panel and Case Section ··········································· 30 Back Panel and Disc Table Section ·································· 31 Chassis Section ································································· 32 Base Unit Section (BU-5BD20) ······································· 33
6.
ELECTRICAL PARTS LIST ................................... 34
SAFETY-RELATED COMPONENT WARNING!! COMPONENTS IDENTIFIED BY MARK ! OR DOTTED LINE WITH MARK ! ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT À LA SÉCURITÉ! LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE ! SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
--2--
MODEL IDENTIFICATION -- BACK PANEL --
SAFETY CHECK-OUT
(US model only) After correcting the original service problem, perform the following safety checks before releasing the set to the customer: Check the antenna terminals, metal trim, "metallized" knobs, screws, and all other exposed metal parts for AC leakage. Check leakage as described below.
4-987-
CDP-C160Z US Model : 782-4 CDP-C260Z US Model : 783-7 Canadian Model : 783-8 CDP-CE215 US Model : 782-0 Canadian Model : 782-1 AEP Model : 782-2 Australian Model : 782-3 CDP-CE315 AEP, East European, North Europian, CIS Model : 783-0 UK Model : 783-1 Singapore Model : 783-2 Australian Model : 783-3 E Model : 783-4 US Model : 783-5 Canadian Model : 783-6
LEAKAGE
The AC leakage from any exposed metal part to earth ground and from all exposed metal parts to any exposed metal part having a return to chassis, must not exceed 0.5 mA (500 microampers). Leakage current can be measured by any one of three methods. 1. A commercial leakage tester, such as the Simpson 229 or RCA WT-540A. Follow the manufacturers' instructions to use these instruments. A battery-operated AC milliammeter. The Data Precision 245 digital multimeter is suitable for this job. Measuring the voltage drop across a resistor by means of a VOM or battery-operated AC voltmeter. The "limit" indication is 0.75 V, so analog meters must have an accurate low-voltage scale. The Simpson 250 and Sanwa SH-63Trd are examples of a passive VOM that is suitable. Nearly all battery operated digital multimeters that have a 2V AC range are suitable. (See Fig. A)
2.
3.
NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK OR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostatic breakdown because of the potential difference generated by the charged electrostatic load, etc. on clothing and the human body. During repair, pay attention to electrostatic breakdown and also use the procedure in the printed matter which is included in the repair parts. The flexible board is easily damaged and should be handled with care.
To Exposed Metal Parts on Set
0.15µF
1.5k
AC voltmeter (0.75V)
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused on the disc reflective surface by the objective lens in the optical pickup block. Therefore, when checking the laser diode emission, observe from more than 30 cm away from the objective lens.
Earth Ground Fig. A. Using an AC voltmeter to check AC leakage.
--3--
HOW TO OPEN THE DISC TRAY WHEN POWER SWITCH TURNS OFF
Insert a tapering driver into the aperture of the unit bottom, and turn in the direction of arrow (to OUT direction). * To close the disc tray, turn the driver in the reverse direction (to IN direction).
IN
OU
T
Tray
NOTE FOR MAIN GEAR INSTALLATION
5 Stopper washer (5)
4 Install the MAIN GEAR as show in the drawing.
3 Rotate the GEAR (U/D) to the arrow Adirection.
A
B
2 Slide the SET LEVER to the arrow B direction.
1 Set the mark of ROTARY ENCODER.
--4--
SECTION 1 GENERAL
Identifying the Parts Front Panel
1 23456 7
8
!¡ !£ 9 0 !TM
!¢
@¢ @ @£ @TM
@¡ !ª !¶ @º !· !§ !
1 2 3 4 5 6 7 8 9 !º !¡ !TM
POWER switch CONTINUE button SHUFFLE button PROGRAM button REPEAT button DISC CHECK button: CE215/CE315 model TIME button: C160Z/C260Z model DISC 1-5 button Display window " (play) button P (pause) button p (stop) button EX-CHANGE button
!£ !¢ ! !§ !¶ !· !ª @º @¡ @TM @£ @¢ @
DISC SKIP button 6 OPEN/CLOSE button AMS knob FADER button MUSIC SCAN button CLEAR button CHECK button ) (forward) button 0 (backward) button Disc tray PEAK SEARCH button: CE215/CE315 model EDIT/TIME FADE button: CE215/CE315 model TIME button: CE215/CE315 model
--5--
SECTION 2 DISASSEMBLY
Note : Follow the disassembly procedure in the numerical order given.
2-1.
CASE, BOTTOM PLATE AND FRONT PANEL
4 Case 1 Two screws (M3 × 8) 3 Two screws (BV3 × 8)
!º Two screws (BVTT3 × 8)
9 Flat type wire (9 core) (MAIN board, to CN402)
2 Two screws (M3 × 8)
!TM Front panel
8 Flat type wire (35 core) (MAIN board, to CN402)
6 Three screws (BVTP3 × 10) !¡ Three screws (BVTP3 × 10) 7 Bottom plate 5 Four screws (BVTP3 × 10)
2-2.
BACK PANEL AND DISC TABLE
!£ Screw (PTPWH3 × 12) !¢ Disc table (B) 3 Back panel 2 Five screws (BVTP3 × 10) ! Disc table (A) !TM Bracket
(guideB1) !¡ Screw (BVTP3 × 8)
1 Connector 9 Screw (BVTP3 × 8) 0 Bracket (guide F1) 4 Flat type wire (6 core) (MAIN board, to CN404) 6 Bracket (guide B1) 5 Screw (BVTP3 × 8)
8 Bracket (guide F1)
7 Screw (BVTP3 × 8)
--6--
2-3.
OPTICAL PICK-UP BLOCK ASSEMBLY
2 Screw (PTPWH3 × 12) 3 Two screws (PTPWH2.6 × 6) 4 Two screws (PTPWH2.6 × 6)
8 Optical pick-up block assembly 6 Compression spring (BU) 1 Flat type wire (16 core) (BD board, to CN101)
5 Holder (BU)
7 Compression spring (BU)
2-4.
BRACKET (GEAR) ASSEMBLY
1 Stopper washer (5) 3 Stopper washer (5) 2 Gear (REV) 7 Stopper washer (5) 4 Gear (MAIN) 8 Gear (U/D)
5 Screw (BVTP3 × 8)
9 Five screws (BVTP3 × 8) 0 Bracket (GEAR) assembly
6 Rotary encoder
Note : As for the installation of the main gear, refer to "Note for MAIN GEAR installation" on page 4.
--7--
SECTION 3 ELECTRICAL BLOCK CHECKING
Note : 1. CD Block is basically designed to operate without adjustment. Therefore, check each item in order given. 2. Use YEDS-18 disc (3-702-101-01) unless otherwise indicated. 3. Use an oscilloscope with more than 10M impedance. 4. Clean the object lens using an applicator with neutral detergent when the signal level is low than specified value with the following checks. Note : A clear RF signal waveform means that the shape " " can be clearly distinguished at the center of the waveform. RF signal waveform
VOLT/DIV : 200mV TIME/DIV : 500ns
S Curve Check
oscilloscope BD board TP (FE) TP (VC)
level : 1.25 ± 0.25 Vp-p
E-F Balance Check
oscilloscope BD board
Procedure : 1. Connect oscilloscope to test point TP (FE) on BD board. 2. Connect between test point TP (FEI) and TP (VC) by lead wire. 3. Turn Power switch on. 4. Put disc (YEDS-18) in and turn Power switch on again and actuate the focus search. (Actuate the focus search when disc table is moving in and out.) 5. Check if the oscilloscope waveform (S-curve) is symmetrical between A and B. And confirm peak to peak level within 3±1 Vp-p. S-curve waveform
symmetry
TP (TE) TP (VC)
Procedure : 1. Connect test point TP1 (ADJ) to ground with a lead wire. 2. Connect oscilloscope to test point TP (TE) on BD board. 3. Turned Power switch on. 4. Put disc (YEDS-18) in to play the number five track. 5. Press the "3" button. (The tracking servo and the sledding servo are turned OFF.) 6. Check the level B of the oscilloscope's waveform and the A (DC voltage) of the center of the Traverse waveform. Confirm the following : A/B × 100 = less than ± 22% Traverse waveform
A within 3 ± 1 Vp-p B
Center of the waveform B
6. After check, remove the lead wire connected in step 2. 0V Note : · Try to measure several times to make sure than the ratio of A : B or B : A is more than 10 : 7. · Take sweep time as long as possible and light up the brightness to obtain best waveform. 7.
A (DC voltage)
level : 1.3 ± 0.6 Vp-p
RF Level Check
oscilloscope BD board TP (RF) TP (VC)
Press the "8" button. (The tracking servo and sledding servo are turned ON.) Confirm the C (DC voltage) is almost equal to the A (DC voltage) is step 6. Traverse waveform
0V Procedure : 1. Connect oscilloscope to test point TP (RF) on BD board. 2. Turned Power switch on. 3. Put disc (YEDS-18) in to play the number five track. 4. Confirm that oscilloscope waveform is clear and check if RF signal level is correct or not.
C (DC voltage)
Tracking servo Sledding servo OFF
Tracking servo Sledding servo ON
8.
Disconnect the lead wire of TP (ADJ) connected in step 1.
--8--
CDP-C160Z/C260Z/CE215/CE315 SECTION 4 DIAGRAMS
RF PLL Free-run Frequency Check
Procedure : 1. Connect frequency counter to test point (PLCK) with lead wire.
BD board TP (PLCK) frequency counter
Adjustment Location :
4-1.
CIRCUIT BOARDS LOCATION
[ BD BOARD ] -- Conductor Side --
1
20
(FE) (FEI)
IC103
(RF)
11
BD BOARD TABLE MOTOR BOARD SENSOR BOARD
2. 3.
Turned Power switch on. Put the disc (YEDS-18) in to play the number five track. Confirm that reading on frequency counter is 4.3218MHz.
10
(TE)
(VC)
LOADING MOTOR BOARD
(PLCK) IC101
POWER SW BOARD
[ MAIN BOARD ] -- Conductor Side --
KEY BOARD
MAIN BOARD
DISPLAY BOARD
41 40 64 65 80 1 25
IC302
24
TP1 (ADJ)
--9--
-- 10 --
CDP-C160Z/C260Z/CE215/CE315
4-8.
IC101
IC BLOCK DIAGRAMS
CXA2545Q
VCKI VPCO FSTO XTAI XTAO XTSL
67 62 63 64 20 19 32K RAM
IC301
INIT 1 SYSM 2
CXD8567AM
28 D Vdd 2
IC603
GND 2
M5293L
MODE
FILI FILO CLTV RFAC ASYI ASYO ASYE WFCK SCOR EXCK SBSO EMPH SQCK SQSO MON FSW MDP MDS
SYNC PROTECTOR ASYMMETRY CORRECTION MUX
SERIAL PARALLEL PROCESSOR
LATCH 5 256FSO 6
SAMPLE HOLD (X1)
FIR3
D/A DATA PROCESSOR
79 MUTE
SHIFT 4
3RD ORDER NOISE SHAPER
C4M C16M PDO VCO1 VCO0 PCO
NOISE SHAPER
18-TIMES OVERSAMPLING FILTER
RFDC 26 TE 27 SE 28 FE 29 VC 30
SWITCH & BUFFER
SERVO DSP A/D CONVERTER SLED SERVO TRACKING SERVO FOCUS SERVO
PWM GENERATOR SLED PWM GENERATOR TRACKING PWM GENERATOR FOCUS PWM GENERATOR
MUTE R 14
2 2 2 2 2 2 3, 100 1, 2 4, 7 5, 6 8, 11 4, 7 9, 10 SFON, SFDR SRON, SRDR TFDR, TFON TRON, TRDR FFDR, FFON TRON, FRDR
MUTE CIRCUIT
MIRR DFCT FOK DETECTOR
89 91 92 93
COUT MIRR DFCT FOK
LRCK 12 MUTE L 13
PLM
68 69 18 13 12 33 32 31 34 36 38 39 42 73 74 76 75 72 78 77 95 94 96 97
CLOCK GENERATOR DIGITAL PLL VARI-PITCH DOUBLE SPEED
DC DITHER
AC DITHER
5k
27 L1 (+)
RESISTER
43 PSSL ADRESS GENERATOR PRIORITY ENCODER 16 61 - 46 DA01-16
5 27k + 3
REFERENCE VOLTAGE
EFM DEMODULATOR
ATT 3
PLM
26 A Vdd L 25 L2 (+) 24 A Vss L 23 X Vss
OUT
ON/OFF
4
REFERENCE VOLTAGE
OVERHEAT PROTECTION OVERCURRENT LIMITTER
IN
1
TIMING CIRCUIT
FIR2
TIMING GENERATOR 1 SUBCODE P-W PROCESSOR SUBCODE 0 PROCESSOR CLV PROCESSOR ERROR CORRECTOR
PEAK DETECTOR DIGITAL OUT 71 D OUT 70 MD2 86 DATA 88 CLOK 87 XLAT
TEST1 7 D Vss 8 MCKSEL 9 XBCK 10 DATA 11
CLOCK GENERATOR
22 512IN 21 X OUT 20 X Vdd
CPU INTERFACE
ATT
19 A Vss R
S/P
TIMING GENERATOR 2 SERVO MICRO PROGRAM INTERFACE
SERVO AUTO SEQUENCER
IIR
80 SENS
18 R2 (+) 17 A Vdd R 16 R1 (+) 15 D Vdd 1
25 24
14 16 17
21 40 23 35
41 90 15 65
81
22 37 44 45 66 82 83 84 85 98 99
IC102
BA6392FP
BUFF F BUFF R LEVEL SHIFT BUFF BUFF 27 CH4 OUT F 26 CH4 OUT R 25 VB IN INTERFACE 24 VS IN BUFF 23 VB IN
IGEN BIAS WDCK LRCK FSTI DIRC SCLK OFSW ATSK LOCK SSTP
AVDD AVDD AVSS AVSS
RFC ADIO
TEST TES2 TES3
ADD ADD DVSS DVSS
XRST
IC103
LD 1 28 GND
CXA1821M
VCC VCC 20 VCC 19 LD ON 18 LC/PD RF EQ AMP 17 RFE VC RF SUMMING AMP VC 16 RFO 15 FE FOCUS ERROR AMP VEE VC VC VC 14 FE BIAS 13 TE VC VC VC BUFFER VC VCC VEE 11 EO 12 VC
IC601
V IN 1
FIR1
LA5602
CH1 OUT F 1 CH1 OUT R 2 CAPA IN 1 3 CH1 R IN 4 CH1 F IN 5 VREF IN 6 VREF OUT 7 GND 8 CH2 F IN 9 CH2 R IN 10 CAPA IN 2 11 CH2 OUT R 12 CH2 OUT F 13 GND 14
PD 2 A 3 VEE B 4 C 5 D 6
REFERENCE VOLTAGE OVER CURRENT LIMITTER OVER HEAT PROTECTION EN 2 ON/OFF
ERROR AMP
VREF
APC LD AMP VEE
R F
22 VCC VEE 7 21 VCC F R INTERFACE INTERFACE F R 20 CH3 F IN 19 CH3 R IN 18 CAPA IN 3 BUFF F R MUTE 15 MUTE BUFF 17 CH3 OUT R 16 CH3 OUT F F 8 E 9 EI 10
TRACKING ERROR AMP
CDEL
3
RESET GEN
GND
4
R BUFF BUFF
F
RES CN
5 6
V OUT
7
-- 23 --
-- 24 --
4-9.
IC PIN FUNCTIONS
· IC101 DIGITAL SIGNAL PROCESSOR (CXD2545Q)
Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 SRON SRDR SFON TFDR TRON TRDR TFON FFDR FRON FRDR FFON VCOO VCOI TEST DVss TES2 TES3 PDO VPCO VCKI AVD2 IGEN AVS2 ADIO RFC RFDC TE SE FE VC FILO FILI PCO CLTV AVS1 RFAC BIAS ASYI ASYO AVD1 Pin Name I/O O O O O O O O O O O O O I I -- I I O O I -- I -- I O I I I I I O I O I -- I I I O -- Sled drive output (Not used) Sled drive output Sled drive output (Not used) Tracking drive output Tracking drive output (Not used) Tracking drive output Tracking drive output (Not used) Focus drive output Focus drive output (Not used) Focus drive output Focus drive output (Not used) VCO output for analog EFM PLL (Not used) VCO output for analog EFM PLL (Ground) TEST pin connected normally to ground Digital ground TEST pin connected normally to ground TEST pin connected normally to ground Charge-pump output for analog EFM PLL (Not used) Charge-pump output for variable pitch PLL (Not used) Clock input from variable pitch external VCO (Ground) Analog power supply Power supply pin for operational amplifiers Analog ground (Not used) (Not used) RF signal input Tracking error signal input Sled error signal input Focus error signal input Center voltage input pin Filter output for master PLL Filter input for master PLL Charge-pump output for master PLL Control voltage input for master VCO Analog ground EFM signal input Asymmetry circuit constant current input Asymmetry comparate voltage input EFM full swing output Analog power supply Function
-- 25 --
Pin No. 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 DVDD ASYE PSSL
Pin Name
I/O -- I I O O O O O O O O O O O O O O O O O O I O I -- I O O O I O O O O O I O I I O Digital power supply Asymmetry circuit ON/OFF Audio data output mode selection input 48-bit slot D/A interface. Word clock. 48-bit slot D/A interface. LR clock.
Function
WDCK LRCK DATA BCLK 64DATA 64BCLK 64LRCK GTOP XUGF XPLCK GFS PFCK C2PO XRAOF MNT3 MNT2 MNT1 MNT0 XTAI XTAO XTSL DVss FSTI FSTO FSOF C16M MD2 DOUT EMPH WFCK SCOR SBSO EXCK SUBQ SQCK MUTE SENS
DA 16 output when PSSL=1.48-bit slot serial data when PSSL=0 DA 15 output when PSSL=1.48-bit slot data when PSSL=0 DA 14 output when PSSL=1.64-bit slot data when PSSL=0 (Not used) DA 13 output when PSSL=1.64-bit slot data when PSSL=0 (Not used) DA 12 output when PSSL=1.64-bit slot data when PSSL=0 (Not used) DA 11 output when PSSL=1.GTOP output when PSSL=0 (Not used) DA 10 output when PSSL=1.XUGF output when PSSL=0 (Not used) DA 09 output when PSSL=1.XPLCK output when PSSL=0 DA 08 output when PSSL=1.GFS output when PSSL=0 DA 07 output when PSSL=1.RFCK output when PSSL=0 DA 06 output when PSSL=1.C2PO output when PSSL=0 (Not used) DA 05 output when PSSL=1.XRA0F output when PSSL=0 DA 04 output when PSSL=1.MNT3 output when PSSL=0 DA 03 output when PSSL=1.MNT2 output when PSSL=0 DA 02 output when PSSL=1.MNT1 output when PSSL=0 DA 01 output when PSSL=1.MNT0 output when PSSL=0 X'tal oscillator circuit input X'tal oscillator circuit output (Not used) X'tal selection input pin (Ground) Digital ground 2/3 divider output of pins 62, 63 2/3 divider output of pins 62, 63 (Not used) 16.9344 MHz output (Not used) Digital-out ON/OFF control pin (+5V) Digital-out output pin Playback disc output in emphasis mode (Not used) WFCK output Sub-code sync output Sub-P through Sub-W serial output (Not used) Clock input for SBS0 read-out (Ground) Sub-Q 80-bit output Muting selection pin SENS output System reset
-- 26 --
Pin No. 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100
Pin Name XRST DIRC SCLK DFSW ATSK DATA XLAT CLOK COUT DVDD MIRR DFCT FOK FSW MON NDP MDS LOCK SSTP SFDR
I/O I I I I I I I I O -- O O O O O O O O I O System reset Used in 1-track jump mode (+5v) SENS serial data read-out clock DFCT selection pin (Ground) Input pin for anti-shock (Ground) Serial data input, supplied from CPU Latch input, supplied from CPU
Function
Serial data transfer clock input, supplied from CPU Numbers of track counted signal output (Not used) Digital power supply Mirror signal output Defect signal output Focus OK output Output to select spindle motor output filter (Not used) Output to control ON/OFF of spindle motor (Not used) Output to control spindle motor servo Output to control spindle motor servo (Not used) GFS is sampled by 460 Hz. H when GFS is H (Not used) Input signal to detect disc inner most track Sled drive output
-- 27 --
· IC302 SYSTEM CONTROL (CXP82324-082Q)
Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 to 37 38 39 40 Pin Name BUS IN RM IN ADJ XLT LD ON TSENS PRGL CLK AMUTE DATA SQCK SUBQ SCLK S1 S2 S3 LED LDOUT LDIN TBLL TBLR CD123 KEY1 KEY2 KEY3 KEY4 KEY5 KEY6 VERSION XRST EXTAL XTAL Vss NC P1 P2 P3 I/O I I I O O I O O O O O I O I I I O O O O O I I I I O O I I I -- -- -- O O O O Not used. (Pull up) Remote control signal input ADJ mode setting pin CXD2545 latch output Laser diode ON output Table position sensor input CXD8567 latch output CXD2545/CXD8567 serial clock output Mute output pin CXD2545/CXD8567 serial data output Subcode Q read clock Subcode Q read data input CXD2545 data read serial clock output CDM27 table rotary encoder input 1 CDM27 table rotary encoder input 2 CDM27 table rotary encoder input 3 Not used. (Open) Loading-out output Loading-in output Rotary table rotation counter-clockwise rotation output Rotary table rotation clockwise rotation output Not used. (Pull up) A/D input 1 for key input A/D input 2 for key input A/D input 3 for key input Not used. (Open) Not used. (Open) A/D input 6 for key input Version setting input pin Reset input Oscillator connection pin Oscillator connection pin Ground Not used. (Open) FL display tube segmant output 1 FL display tube segmant output 2 FL display tube segmant output 3 Function
-- 28 --
Pin No. 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 to 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 P4 P5 P6 P7 P8 P9 P10 P11 P12 P13 P14 P15 P16 P17 P18 P19 P20 NC G1 G2 G3 G4 G5 G6 G7 G8 VG VDD NC NC NC
Pin Name
I/O O O O O O O O O O O O O O O O O O O O O O O O O O O -- -- -- O O I O I I I FL display tube segmant output 4 FL display tube segmant output 5 FL display tube segmant output 6 FL display tube segmant output 7 FL display tube segmant output 8 FL display tube segmant output 9 FL display tube segmant output 10 FL display tube segmant output 11 FL display tube segmant output 12 FL display tube segmant output 13 FL display tube segmant output 14 FL display tube segmant output 15 FL display tube segmant output 16 FL display tube segmant output 17 FL display tube segmant output 18 FL display tube segmant output 19 FL display tube segmant output 20 Not used. (Open) FL display tube grid output 1 FL display tube grid output 2 FL display tube grid output 3 FL display tube grid output 4 FL display tube grid output 5 FL display tube grid output 6 FL display tube grid output 7 FL display tube grid output 8
Function
FL display tube filament voltage (30 V) +5V +5V Not used. (Open) Not used. (Open) AFADJ mode setting pin Not used. (Open) Disc sensor input CXD2545 internal state monitor input Subcode sync. input
AFADJ BUS OUT DSENS SENS SCOR
-- 29 --
SECTION 5 EXPLODED VIEWS
NOTE: · Items marked "*" are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. · The mechanical parts with no reference number in the exploded views are not supplied. · Hardware (#mark) list is given in the last of this parts list. · Abbreviation CND : Canadian model EE : East European model AUS : Australian model AED: North European model SP: Singapore model
The components identified by mark ! or dotted line with mark ! are critical for safety. Replace only with part number specified. Les composants identifiés par une marque ! sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifie.
5-1. FRONT PANEL AND CASE SECTION 11
12 13
#2 not supplied
13 5
8 3 18 20 16 9 4 17 19 7 1 10 21
#1
5 5 6 5
2
5
not supplied #1
#1
14 #1
15
22
Ref. No. 1 2 2 3 4 5 * 6 7 * 8 9 10 10 10 10
Part No. 4-987-780-01 4-987-779-01 4-987-779-11 4-977-589-01 3-008-600-01 4-951-620-01 1-664-522-11 1-777-837-11 1-664-523-11 1-777-838-11 4-987-773-01 4-987-773-11 4-987-773-21 4-987-773-71
Description PANEL, LOADING WINDOW (FL) (C160Z/CE215) WINDOW (FL) (C260Z/CE315) BUTTON (POWER) EMBLEM (5-AR), SONY SCREW (2.6X8), +BVTP DISPLAY BOARD WIRE (FLAT TYPE) (35 CORE) POWER SW BOARD WIRE (FLAT TYPE) (6 CORE) PANEL, FRONT (CE215) PANEL, FRONT (CE315) PANEL, FRONT (C160Z) PANEL, FRONT (C260Z)
Remarks
Ref. No. * 11 12 13 14 14 * 15 * 16 17 18 19 20 21 22
Part No. 4-978-492-11 3-703-685-21 3-704-366-01 X-4946-618-1 X-4946-641-1 4-978-398-21 1-664-524-11 4-987-775-01 4-987-776-01 4-987-777-01 4-987-774-01
Description CASE SCREW (+BV 3X8) SCREW (CASE) (M3X8) FOOT ASSY (US,CND) FOOT ASSY (EXCEPT US,CND) CUSHION KEY BOARD BUTTON (PLAY) BUTTON (FUNC)(CE215/CE315) BUTTON (FF) BUTTON (MODE)
Remarks
4-987-994-01 KNOB (AMS) 4-977-593-01 RING (DIA. 50), ORNAMENTAL (EXCEPT US,CND)
-- 30 --
5-2. BACK PANEL AND DISC TABLE SECTION
#3
52
not supplied
53 55
51
#4 not supplied
M801
56
US, CND MODEL
63 65 66 67
#6
#5
57 58
UK MODEL
59
AUS MODEL
64 63 60 61
59
59
AEP, AED, EE, CIS, SP MODEL
62 59 63 64 73 54 72
#4
E MODEL
59 68 70
#1 #1 #1
64 63
74
#4 not supplied #4
not supplied
71
#4
not supplied
69
#4 not supplied
Ref. No. 51 52 53 * 54 * 55 56 57 58 ! 59 ! 59 ! 59 ! 59 ! 59 60 61 62 63 64 65 66 67 Part No. 4-957-299-11 4-957-304-01 X-4943-479-1 1-659-737-11 1-647-364-11 3-325-697-01 4-957-284-01 X-4943-477-1 1-558-943-61 1-575-651-21 1-590-926-11 1-696-845-11 1-751-529-11 4-957-293-01 4-957-291-11 4-957-868-01 X-4924-457-1 4-934-376-01 4-957-292-11 Description TABLE (B), DISC BELT (RM) GEAR (ROTARY A) ASSY SENSOR BOARD TABLE MOTOR BOARD WASHER GEAR (ROTARY B) BRACKET (RM) ASSY CORD, POWER (E) CORD, POWER (AEP,AED,EE,CIS,SP) CORD, POWER (US,CND) CORD, POWER (AUS) CORD, POWER (UK) SPRING (RACK RELEASE) LEVER (RACK RELEASE) SCREW (+PTPWH 2.6X20) ROLLER ASSY SHAFT (ROLLER) SLIDER (RACK) Remarks
#4
Ref. No. ! 68 * 69 * 70 * 70 * 71 * 71 * 71 * 71 * 71 * 71 * 71 * 71 * 71 * 71 * 71 * 71 * 71 * 71 72 73 74 M801 Part No. 1-569-007-11 4-951-619-01 3-703-244-00 3-703-571-11 4-987-782-01 4-987-782-11 4-987-782-21 4-987-782-31 4-987-782-41 4-987-783-01 4-987-783-11 4-987-783-21 4-987-783-31 4-987-783-41 4-987-783-51 4-987-783-61 4-987-783-71 4-987-783-81 1-751-052-11 Description ADAPTOR, CONVERSION 2P (E) CUSHION (A) BUSHING (2104), CORD (EXCEPT E) BUSHING (S) (4516), CORD (E) PANEL, BACK (CE215:US) PANEL, BACK (CE215:CND) PANEL, BACK (CE215:AEP) PANEL, BACK (CE215:AUS) PANEL, BACK (C160Z,US) PANEL, BACK (CE315:AEP,AED,EE,CIS) PANEL, BACK (CE315:UK) PANEL, BACK (CE315:SP) PANEL, BACK (CE315:AUS) PANEL, BACK (CE315:E) PANEL, BACK (CE315:US) PANEL, BACK (CE315:CND) PANEL, BACK (C260Z:US) PANEL, BACK (C260Z:CND) WIRE (FLAT TYPE) (6 CORE) Remarks
4-957-294-01 SPRING (D.T), TENSION 4-957-298-01 TABLE (A), DISC
X-4943-480-1 BRACKET (ROLLER D) ASSY 1-500-455-11 CORE, FERRITE A-4660-525-A MOTOR ASSY, ROTARY (TABLE)
The components identified by mark ! or dotted line with mark ! are critical for safety. Replace only with part number specified. Les composants identifiés par une marque ! sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifie.
-- 31 --
5-3.
CHASSIS SECTION 101 101 102 103 101
BU-5BD20
107
#3
107
104 109 108 125
#4 #4 #4 not supplied
108 110
105
106 128 114 117 116 115 127 112 113
not supplied
#4
118
T601 M802 not supplied
119
#8
121
#1
120
124
#1
123 122
Ref. No. 101 102 103 104 105 106 107 108 109 110 112 113 114 115 116 117 * 118 119
Part No. 4-957-283-01 4-957-288-01 4-957-287-01 4-957-286-01 1-466-996-11 X-4946-195-1 4-933-134-01 4-948-503-01 1-765-443-11 4-957-289-12 4-957-281-01 4-957-279-11 4-957-303-01 4-934-375-01 4-957-285-01
Description WASHER (5), STOPPER GEAR (MAIN) GEAR (REV) GEAR (U/D) ENCODER, ROTARY BRACKET (GEAR) ASSY SCREW (+PTPWH M2.6X6) SPRING (BU), COMPRESSION WIRE (FLAT TYPE) (23 CORE) HOLDER (BU) SPRING (LOCK LEVER) LEVER, LOCK GEAR (LOADING C) GEAR (LOADING B) LEVER, SET
Remarks
Ref. No. 120 * 121 * 122 123 * 124 * 124 * 124 * 124 * 124 125 * 127 * 128 ! T601 ! T601 ! T601 M802
Part No. 4-944-490-01 4-957-555-01 4-957-556-01 3-531-576-11 A-4699-469-A A-4699-472-A
Description
Remarks
BELT (TIMING) SHEET, INSULATING (EXCEPT US,CND) SHEET, INSULATING (EXCEPT US,CND) RIVET (EXCEPT US,CND) MAIN BOARD, COMPLETE (C160Z/C260Z) MAIN BOARD, COMPLETE (CE215:AUS/CE315:AUS,SP) A-4699-476-A MAIN BOARD, COMPLETE (CE215:US,CND/CE315:US,CND) A-4699-477-A MAIN BOARD, COMPLETE (CE215:AEP/CE315:AEP,UK,AED,EE,CIS) A-4699-565-A MAIN BOARD, COMPLETE (CE315:E) 1-452-838-12 4-981-731-01 4-981-731-11 1-429-956-11 1-431-076-11 1-431-168-11 A-4660-914-A MAGNET (ASSY) CUSHION (U/D) CUSHION (U/D) TRANSFORMER, POWER (US,CND) TRANSFORMER, POWER (EXCEPT US,CND,E) TRANSFORMER, POWER (E) MOTOR ASSY (LOADING)
4-962-087-01 SPRING (S), TENSION 1-659-738-11 LOADING MOTOR BOARD X-4941-529-1 PULLEY ASSY
-- 32 --
The components identified by mark ! or dotted line with mark ! are critical for safety. Replace only with part number specified.
Les composants identifiés par une marque ! sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifie.
5-4.
BASE UNIT SECTION (BU-5BD20)
751
752
753
#7
755
M101
754
M102
754
S101
756
757 758
Ref. No. ! 751 752 753 754 755 756
Part No. 8-848-379-31 1-769-069-11 4-917-567-01 4-951-940-01 4-917-565-01 4-917-564-01
Description OPTICAL PICK UP KSS-213BA/F-NP WIRE (FLAT TYPE) (16 CORE) GEAR (M) INSULATOR (BU) SHAFT, SLED GEAR (P), FLATNESS
Remarks
Ref. No. * 757 758 M101 M102 S101
Part No. A-4673-510-A 4-951-620-01 X-4917-523-3 X-4917-504-1 1-572-085-11
Description BD BOARD, COMPLETE SCREW (2.6X8), +BVTP MOTOR ASSY (SPINDLE) MOTOR ASSY (SLED) SWITCH, LEAF (LIMIT)
Remarks
-- 33 --
The components identified by mark ! or dotted line with mark ! are critical for safety. Replace only with part number specified.
Les composants identifiés par une marque ! sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifie.
BD
NOTE:
DISPLAY
·
SECTION 6 ELECTRICAL PARTS LIST
Due to standardization, replacements in the parts list may be different from the parts specified in the diagrams or the components used on the set. Items marked "*" are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. RESISTORS All resistors are in ohms METAL: Metal-film resistor F : nonflammable · SEMICONDUCTORS In each case, u: µ , for example: uA...: µ A..., uPA...: µ PA..., uPB...: µ PB..., uPC...: µ PC..., uPD...: µ PD... CAPACITORS uF : µ F COILS uH : µ H Abbreviation CND : Canadian model EE : East European model AUS : Australian model AED: North European model SP: Singapore model
When indicating parts by reference number, please include the board naame. The components identified by mark ! or dotted line with mark ! are critical for safety. Replace only with part number specified. Les composants identifiés par une marque ! sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifie.
·
· · ·
·
Ref. No. *
Part No.
Description
Remarks
Ref. No.
Part No.
Description < RESISTOR >
Remarks
A-4673-510-A BD BOARD, COMPLETE ******************* < CAPACITOR > C101 C102 C103 C105 C106 C107 C108 C109 C110 C111 C112 C113 C115 C116 C117 C118 C119 C123 C124 C140 C141 C151 C153 C154 C156 C157 C159 C161 1-163-005-11 1-163-038-00 1-163-005-11 1-135-155-21 1-164-346-11 1-164-346-11 1-163-035-00 1-163-145-00 1-163-017-00 1-163-251-11 1-163-038-00 1-163-038-00 1-126-607-11 1-126-607-11 1-126-209-11 1-163-275-11 1-163-231-11 1-164-232-11 1-164-005-11 1-163-038-00 1-163-038-00 1-163-237-11 1-163-038-00 1-164-336-11 1-163-237-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP TANTALUM CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CHIP ELECT CHIP ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 470PF 0.1uF 470PF 4.7uF 1uF 10% 10% 10% 50V 25V 50V 16V 16V 16V 50V 50V 50V 50V 25V 25V 4V 4V 4V 50V 50V 50V 25V 25V 25V 50V 25V 25V 50V 50V 50V 25V R101 R102 R103 R104 R105 R106 R107 R108 R109 R110 R112 R123 R124 R125 R126 R127 R131 R135 R136 R137 R138 R141 R142 R143 R144 R146 R147 R148 R149 R158 R159 R160 R161 R162 1-216-077-00 1-216-097-00 1-216-077-00 1-216-085-00 1-216-097-00 1-216-061-00 1-216-061-00 1-216-073-00 1-216-121-00 1-216-025-00 1-216-049-11 1-216-073-00 1-216-097-00 1-216-049-11 1-216-049-11 1-216-049-11 1-216-037-00 1-216-295-00 1-216-295-00 1-216-295-00 1-216-295-00 1-216-089-00 1-216-081-00 1-216-103-00 1-216-103-00 1-216-073-00 1-216-081-00 1-216-001-00 1-216-003-11 1-216-111-00 1-216-101-00 1-216-295-00 1-216-308-00 1-216-101-00
METAL CHIP METAL GLAZE METAL CHIP METAL CHIP METAL GLAZE METAL CHIP METAL CHIP METAL CHIP METAL GLAZE METAL GLAZE METAL GLAZE METAL CHIP METAL GLAZE METAL GLAZE METAL GLAZE
15K 100K 15K 33K 100K 3.3K 3.3K 10K 1M 100 1K 10K 100K 1K 1K
5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W
1uF 0.047uF 0.0015uF 5% 0.0047uF 5% 100PF 5% 0.1uF 0.1uF 47uF 47uF 100uF 0.001uF 15PF 0.01uF 0.47uF 0.1uF 0.1uF 27PF 0.1uF 0.33uF 27PF
20% 20% 20% 5% 5%
METAL GLAZE 1K METAL CHIP 330 CONDUCTOR, CHIP (2012) CONDUCTOR, CHIP (2012) CONDUCTOR, CHIP (2012) CONDUCTOR, CHIP (2012) METAL GLAZE 47K METAL CHIP 22K METAL CHIP 180K METAL CHIP 180K METAL CHIP METAL CHIP METAL CHIP METAL GLAZE METAL GLAZE 10K 22K 10 12 390K
5%
5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W
5%
1-163-145-00 CERAMIC CHIP 1-163-019-00 CERAMIC CHIP 1-163-038-00 CERAMIC CHIP < CONNECTOR >
0.0015uF 5% 0.0068uF 10% 0.1uF
CN101 CN102
1-770-072-11 CONNECTOR,(LIF(NON-ZIF))FFC23P 1-770-014-11 CONNECTOR, FFC/FPC 16P < IC >
METAL CHIP 150K CONDUCTOR, CHIP (2012) METAL CHIP 4.7 METAL CHIP 150K < SWITCH >
IC101 IC102 IC103
8-752-369-78 IC CXD2545Q 8-759-176-09 IC BA6392FP 8-752-072-45 IC CXA1821M < TRANSISTOR >
S101 1-572-085-11 SWITCH, LEAF (LIMIT) ************************************************************ * 1-664-522-11 DISPLAY BOARD ************* < CAPACITOR >
Q101
8-729-010-08 TRANSISTOR MSB710-R C801 1-126-968-11 ELECT 100uF 20% 6.3V
-- 34 --
DISPLAY
Ref. No. Part No. Description < CONNECTOR > * CN810 1-691-958-11 SOCKET, CONNECTOR 35P < FILTER > FL810 1-517-616-11 TUBE, FLUORESCENT INDICATOR < IC > * IC810 8-759-459-84 IC NJL56H400 < RESISTOR > R801 R802 R811 R812 R813 R814 R815 R816 R817 R818 R819 R820 R821 R822 R823 R824 1-247-807-31 1-247-807-31 1-249-415-11 1-249-417-11 1-249-419-11 1-249-421-11 1-247-843-11 1-249-427-11 1-249-415-11 1-249-417-11 1-249-419-11 1-249-421-11 1-247-843-11 1-249-427-11 1-249-431-11 CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON 100 100 680 1K 1.5K 2.2K 3.3K 6.8K 680 1K 1.5K 2.2K 3.3K 6.8K 15K 15K 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 1/4W 1/4W 1/4W F 1/4W F 1/4W F 1/4W 1/4W 1/4W 1/4W 1/4W F F F F * S713 Remarks Ref. No.
KEY
Part No.
LOADING MOTOR
Description < SWITCH >
MAIN
Remarks
1-554-303-21 SWITCH, TACTILE (PEAK SEARCH) (CE215/CE315) S714 1-554-303-21 SWITCH, TACTILE (EDIT/TIME FADE) (CE215/CE315) S715 1-554-303-21 SWITCH, TACTILE (TIME)(CE215/CE315) ************************************************************ 1-659-738-11 LOADING MOTOR BOARD ********************* < MOTOR > M802 A-4660-914-A MOTOR ASSY (LOADING) ************************************************************ * * A-4699-469-A MAIN BOARD, COMPLETE (C160Z/C260Z) ********************* A-4699-472-A MAIN BOARD, COMPLETE ********************* (CE215:AUS/CE315:AUS,SP) A-4699-476-A MAIN BOARD, COMPLETE ********************* (CE215:US,CND/CE315:US,CND) A-4699-477-A MAIN BOARD, COMPLETE ********************* (CE215:AEP/CE315:AEP,UK,AED,EE,CIS) A-4699-565-A MAIN BOARD, COMPLETE (CE315:E) ********************* 7-685-871-01 SCREW +BVTT 3X6 (S)
* 1/4W F 1/4W F 1/4W 1/4W F 1/4W 1/4W
*
1-249-431-11 CARBON < SWITCH >
< CAPACITOR > C301 C302 C303 C304 C305 C306 C307 C308 C316 C317 C374 S812 1-554-303-21 SWITCH, TACTILE (P) S813 1-554-303-21 SWITCH, TACTILE (·) S814 1-473-957-11 ENCODER, ROTARY (AMS) ************************************************************ * 1-664-524-11 KEY BOARD ********** < CONNECTOR > CN701 CN702 1-568-849-11 SOCKET, CONNECTOR 6P 1-750-195-11 CONNECTOR, BOARD TO BOARD 6P < RESISTOR > R713 R714 1-249-415-11 CARBON 680 5% 1/4W F (CE215/CE315) 1-249-417-11 CARBON 1K 5% 1/4W F (CE215/CE315) C406 C407 C408 C410 C412 C501 C502 C503 C504 C505 1-124-443-00 1-161-494-00 1-104-664-11 1-162-290-31 1-164-159-11 1-162-282-31 1-162-215-31 1-162-215-31 1-130-479-00 1-130-472-00 ELECT CERAMIC ELECT CERAMIC CERAMIC CERAMIC CERAMIC CERAMIC MYLAR MYLAR 100uF 0.022uF 47uF 470PF 0.1uF 100PF 47PF 47PF 0.0047uF 0.0012uF 20% 20% 10% 10V 25V 16V 50V 50V 50V 50V 50V 50V 50V C375 C401 C402 C403 C404 C405 1-162-199-31 1-162-199-31 1-164-159-11 1-164-159-11 1-124-443-00 1-124-442-00 1-164-159-11 1-164-159-11 1-164-159-11 1-161-494-00 CERAMIC CERAMIC CERAMIC CERAMIC ELECT ELECT CERAMIC CERAMIC CERAMIC CERAMIC 10PF 10PF 0.1uF 0.1uF 100uF 330uF 0.1uF 0.1uF 0.1uF 0.022uF 5% 5% 50V 50V 50V 50V 10V 6.3V 50V 50V 50V 25V
S801 S802 S803 S804 S805 S806 S808 S809 S810 S811
1-554-303-21 1-554-303-21 1-554-303-21 1-554-303-21 1-554-303-21 1-554-303-21 1-554-303-21 1-554-303-21 1-554-303-21 1-554-303-21
SWITCH, TACTILE (FADER) SWITCH, TACTILE (MUSIC SCAN) SWITCH, TACTILE (CLEAR) SWITCH, TACTILE (CHECK) SWITCH, TACTILE ()) SWITCH, TACTILE (0) SWITCH, TACTILE (OPEN/CLOSE) SWITCH, TACTILE (DISC SKIP) SWITCH, TACTILE (EX-CHANGE) SWITCH, TACTILE (p)
20% 20%
1-104-664-11 ELECT 1-161-494-00 1-162-282-31 1-162-215-31 1-162-215-31 1-130-479-00 1-130-472-00
47uF 20% 16V (CE215:AEP/CE315:AEP,UK,AED,EE,CIS) CERAMIC 0.022uF 25V (CE215:AEP/CE315:AEP,UK,AED,EE,CIS) CERAMIC 100PF 10% 50V CERAMIC 47PF 5% 50V CERAMIC 47PF 5% 50V MYLAR 0.0047uF 5% 50V MYLAR 0.0012uF 5% 50V
10% 5% 5% 5% 5%
-- 35 --
MAIN
Ref. No. C506 C507 C508 C509 C510 C512 C602 C603 C604 C605 C606 C607 C608 C609 C610 C614 C616 C619 C620 C622 C625 C626 C628 C648 C649 C651 Part No. 1-124-443-00 1-161-494-00 1-104-664-11 1-126-962-11 1-162-290-31 1-164-159-11 1-126-944-11 1-126-942-61 1-126-963-11 1-126-963-11 1-126-963-11 1-126-941-11 1-104-666-11 1-124-918-11 1-124-907-11 1-104-665-11 1-161-494-00 1-104-664-11 1-161-494-00 1-161-494-00 1-161-494-00 1-161-494-00 1-104-664-11 1-161-494-00 1-161-494-00 Description ELECT CERAMIC ELECT ELECT CERAMIC CERAMIC ELECT ELECT ELECT ELECT ELECT ELECT ELECT ELECT ELECT ELECT CERAMIC ELECT CERAMIC CERAMIC CERAMIC CERAMIC ELECT CERAMIC CERAMIC 100uF 0.022uF 47uF 3.3uF 470PF 0.1uF 3300uF 1000uF 4.7uF 4.7uF 4.7uF 470uF 220uF 47uF 10uF 100uF 0.022uF 47uF 0.022uF 0.022uF 0.022uF 0.022uF 47uF 0.022uF 0.022uF 47uF 20% 20% 20% 10% Remarks 10V 25V 16V 50V 50V 50V 16V 16V 50V 50V 50V 6.3V 10V 63V 50V 16V 25V 16V 25V 25V 25V 25V 16V 25V 25V 16V Q601 < CONNECTOR > < RESISTOR > CN401 CN402 CN403 * CN404 * CN601 1-750-640-11 1-764-411-11 1-568-849-11 1-568-825-11 1-573-047-11 CONNECTOR, FFC/FPC 23P PIN, CONNECTOR (PC BOARD) 35P SOCKET, CONNECTOR 6P SOCKET, CONNECTOR 6P PIN, CONNECTOR (PC BOARD) 2P < DIODE > D302 D601 D602 D603 D604 D605 D606 D608 D609 8-719-987-63 8-719-200-82 8-719-200-82 8-719-200-82 8-719-200-82 8-719-200-82 8-719-923-60 8-719-987-63 8-719-010-34 DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE < IC > IC301 IC302 IC304 IC371 IC401 IC501 IC601 IC602 IC603 8-759-362-47 8-752-884-93 8-759-356-03 8-749-921-12 8-759-145-58 8-759-145-58 8-759-061-65 8-749-011-78 8-759-633-42 IC IC IC IC IC IC IC IC IC CXD8567AM CXP82324-082Q BA6780 GP1F32T (DIGITAL OUT) (CE215:AEP/CE315:AEP,UK,AED,EE,CIS) uPC4558C uPC4558C LA5602 BA17807T M5293L 1N4148M 11ES2 11ES2 11ES2 11ES2 11ES2 MTZJ-T-77-9.1A 1N4148M UZ-4.7BSC R254 R262 R263 R301 R302 R303 R304 R305 R308 R309 R310 R311 R312 R313 R314 R315 R316 R317 R318 R319 R321 R322 R323 R324 R325 1-249-430-11 1-249-382-11 1-249-382-11 1-249-424-11 1-247-807-31 1-249-411-11 1-249-413-11 1-249-417-11 1-249-429-11 1-249-417-11 1-249-417-11 1-249-425-11 1-249-437-11 1-249-429-11 1-249-425-11 1-249-425-11 1-249-425-11 1-249-427-11 1-249-427-11 1-249-427-11 1-249-429-11 1-249-429-11 1-249-441-11 1-249-429-11 1-249-429-11 CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON 12K 1.2 1.2 3.9K 100 330 470 1K 10K 1K 1K 4.7K 47K 10K 4.7K 4.7K 4.7K 6.8K 6.8K 6.8K 10K 10K 100K 10K 10K 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 1/4W 1/6W F 1/6W F 1/4W F 1/4W 1/4W 1/4W F 1/4W F 1/4W 1/4W F 1/4W F 1/4W F 1/4W 1/4W 1/4W F 1/4W 1/4W 1/4W 1/4W 1/4W F F F F F R205 R206 R251 R252 R253 1-249-430-11 1-249-429-11 1-249-429-11 1-249-426-11 1-249-425-11 CARBON CARBON CARBON CARBON CARBON 12K 10K 10K 5.6K 4.7K 5% 5% 5% 5% 5% 1/4W 1/4W 1/4W 1/4W 1/4W F 8-729-119-76 TRANSISTOR 2SA1175-HFE Ref. No. Part No. Description < COIL > L301 L302 L303 L304 L305 L306 L307 L401 L501 L601 L603 L604 L605 L606 L607 L608 L609 1-410-503-11 1-412-473-21 1-410-503-11 1-410-503-11 1-410-397-21 1-412-473-51 1-412-473-21 1-410-503-11 1-410-503-11 1-412-473-21 1-412-473-21 1-412-473-21 1-410-503-11 1-410-397-21 1-410-503-11 INDUCTOR 3.3uH INDUCTOR 0uH INDUCTOR 3.3uH INDUCTOR 3.3uH FERRITE BEAD INDUCTOR INDUCTOR INDUCTOR INDUCTOR INDUCTOR INDUCTOR 0uH 0uH 3.3uH 3.3uH 0uH Remarks
20% 20% 20% 20% 20% 20% 20% 20% 20% 20% 20%
INDUCTOR 0uH INDUCTOR 0uH INDUCTOR 3.3uH FERRITE BEAD INDUCTOR INDUCTOR 3.3uH 3.3uH 0uH
1-410-503-11 INDUCTOR 1-412-473-21 INDUCTOR
< TRANSISTOR > Q201 Q402 Q404 Q502 Q503 8-729-119-78 8-729-141-26 8-729-119-78 8-729-141-26 8-729-029-56 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR 2SC2785-HFE 2SC3622A-LK 2SC2785-HFE 2SC3622A-LK DTA144ESA
20%
1-104-664-11 ELECT
20%
< JACK > J301 1-770-719-11 JACK, PIN 2P (LINE OUT)
5% 1/4W 5% 1/4W 5% 1/4W 5% 1/4W 5% 1/4W (C160Z/C260Z)
-- 36 --
MAIN
Ref. No. R331 R333 R403 R404 R405 R406 R407 R408 R409 R410 R411 R412 R416 R503 R504 R505 R506 R507 R508 R509 R510 R511 R512 R516 R517 R601 R602 R603 R604 R607 Part No. 1-249-427-11 1-249-429-11 1-249-436-11 1-249-436-11 1-249-431-11 1-249-431-11 1-215-461-00 1-215-461-00 1-249-419-11 1-249-419-11 1-247-887-00 1-249-417-11 1-249-425-11 1-249-436-11 1-249-436-11 1-249-431-11 1-249-431-11 1-215-461-00 1-215-461-00 1-249-419-11 1-249-419-11 1-247-887-00 1-249-417-11 1-249-425-11 1-249-441-11 1-249-435-11 1-249-429-11 1-249-438-11 1-249-429-11 1-249-411-11 Description CARBON CARBON CARBON CARBON CARBON CARBON METAL METAL CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON METAL METAL CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON < SWITCH > ! S601 6.8K 10K 39K 39K 15K 15K 47K 47K 1.5K 1.5K 220K 1K 4.7K 39K 39K 15K 15K 47K 47K 1.5K 1.5K 220K 1K 4.7K 100K 33K 10K 56K 10K 330 5% 5% 5% 5% 5% 5% 1% 1% 5% 5% 5% 5% 5% 5% 5% 5% 5% 1% 1% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5%
POWER SW
Remarks 1/4W F 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W F 1/4W F 1/4W 1/4W F 1/4W F 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W F 1/4W F 1/4W 1/4W F 1/4W F 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W Ref. No. Part No.
SENSOR
Description < SWITCH >
TABLE MOTOR
Remarks
S701 S702 S703 S704 S705 S706 S707 S708 S709 S710
1-554-303-21 1-554-303-21 1-554-303-21 1-554-303-21 1-554-303-21 1-554-303-21 1-554-303-21 1-554-303-21 1-554-303-21 1-554-303-21
SWITCH, TACTILE (DISC 1) SWITCH, TACTILE (DISC 2) SWITCH, TACTILE (DISC 3) SWITCH, TACTILE (DISC 4) SWITCH, TACTILE (DISC 5) SWITCH, TACTILE (CONTINUE) SWITCH, TACTILE (SHUFFLE) SWITCH, TACTILE (PROGRAM) SWITCH, TACTILE (REPEAT) SWITCH, TACTILE (CE215,CE315:DISC CHECK/C160Z,C260Z:TIME)
S751 1-554-118-00 SWITCH, PUSH (1 KEY) (POWER) ************************************************************ * 1-659-737-11 SENSOR BOARD ************ < CONNECTOR > CN851 CN852 1-573-383-11 PIN, CONNECTOR (PC BOARD) 2P 1-750-243-11 SOCKET, CONNECTOR 6P < DIODE > D851 D852 8-749-924-18 DIODE PHOTO INTERRUPTER RPI-1391 8-749-924-30 DIODE PHOTO REFLECTOR GP2S28 < RESISTOR > R851 1-249-416-11 CARBON 820 5% 1/4W F R852 1-249-406-11 CARBON 120 5% 1/4W F ************************************************************ * 1-647-364-11 TABLE MOTOR BOARD ****************** < MOTOR > M801 A-4660-525-A MOTOR ASSY, ROTARY (TABLE) ************************************************************ MISCELLANEOUS ************** 7 9 ! 59 ! 59 ! 59 ! 59 ! 59 ! 68 72 74 105 109 125 ! 751 752 1-777-837-11 1-777-838-11 1-558-943-61 1-575-651-21 1-590-926-11 1-696-845-11 1-751-529-11 1-569-007-11 1-751-052-11 1-500-455-11 1-466-996-11 1-765-443-11 1-452-838-12 8-848-379-31 1-769-069-11 WIRE (FLAT TYPE) (35 CORE) WIRE (FLAT TYPE) (6 CORE) CORD, POWER (E) CORD, POWER (AEP,AED,EE,CIS,SP) CORD, POWER (US,CND) CORD, POWER (AUS) CORD, POWER (UK) ADAPTOR, CONVERSION 2P (E) WIRE (FLAT TYPE) (6 CORE) CORE, FERRITE ENCODER, ROTARY WIRE (FLAT TYPE) (23 CORE) MAGNET (ASSY) OPTICAL PICK UP KSS-213BA/F-NP WIRE (FLAT TYPE) (16 CORE)
1-572-675-11 SWITCH, POWER VOLTAGE CHANGE (VOLTAGE SELECTOR)(E) < VIBRATOR >
X301 1-579-833-21 VIBRATOR, CRYSTAL 33MHz X401 1-579-175-11 VIBRATOR, CERAMIC 10MHz ************************************************************ * 1-664-523-11 POWER SW BOARD **************** < CONNECTOR > CN703 1-750-186-11 CONNECTOR, BOARD TO BOARD 6P < RESISTOR > R701 R702 R703 R704 R705 R706 R707 R708 R709 R709 1-249-415-11 1-249-417-11 1-249-419-11 1-249-421-11 1-247-843-11 CARBON CARBON CARBON CARBON CARBON 680 1K 1.5K 2.2K 3.3K 6.8K 15K 1.5K 2.2K 680 5% 5% 5% 5% 5% 1/4W 1/4W 1/4W 1/4W 1/4W F F F F
1-249-427-11 CARBON 1-249-431-11 CARBON 1-249-419-11 CARBON 1-249-421-11 CARBON 1-249-415-11 CARBON
5% 1/4W F 5% 1/4W 5% 1/4W F (CE215/CE315) 5% 1/4W F (CE215/CE315) 5% 1/4W F (C160Z/C260Z)
-- 37 --
The components identified by mark ! or dotted line with mark ! are critical for safety. Replace only with part number specified.
Les composants identifiés par une marque ! sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifie.
CDP-C160Z/C260Z/CE215/CE315
Ref. No. M101 M102 M801 M802
Part No. X-4917-523-3 X-4917-504-1 A-4660-525-A A-4660-914-A
Description MOTOR ASSY (SPINDLE) MOTOR ASSY (SLED) MOTOR ASSY, ROTARY (TABLE) MOTOR ASSY (LOADING)
Remarks
Ref. No.
Part No.
Description ************** HARDWARE LIST **************
Remarks
S101 1-572-085-11 SWITCH, LEAF (LIMIT) ! T601 1-429-956-11 TRANSFORMER, POWER (US,CND) ! T601 1-431-076-11 TRANSFORMER, POWER (EXCEPT US,CND,E) ! T601 1-431-168-11 TRANSFORMER, POWER (E) ************************************************************ ACCESSORIES & PACKING MATERIALS ******************************* 1-473-519-11 REMOTE COMMANDER (RM-DC41) (C260Z/CE315) 1-558-271-11 CORD, CONNECTION (AUDIO)108cm 3-859-177-11 MANUAL, INSTRUCTION (ENGLISH) (US,UK,AUS) 3-859-177-21 MANUAL, INSTRUCTION (ENGLISH/FRENCH/SPANISH/PORTUGUESE/CHINESE) (CND,AEP,E,SP) 3-859-177-31 MANUAL, INSTRUCTION (GERMAN/DUTCH/ITALIAN/SWEDISH)(AEP,AED) 3-859-177-41 MANUAL, INSTRUCTION (DANISH/FINNISH) (AED) 3-859-177-51 MANUAL, INSTRUCTION (ENGLISH/POLISH/RUSSIAN)(EE,CIS) 4-941-762-11 COVER (MLY), BATTERY (C260Z/CE315) ************************************************************
The components identified by mark ! or dotted line with mark ! are critical for safety. Replace only with part number specified. Les composants identifiés par une marque ! sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifie.
#1 #2 #3 #4 #5 #6 #7 #8
7-685-647-79 7-685-872-09 7-685-648-79 7-685-646-79 7-621-772-00
SCREW +BVTP 3X10 TYPE2 N-S SCREW +BVTT 3X8 (S) SCREW (M3X12), TAPPING SCREW +BVTP 3X8 TYPE2 N-S SCREW +B 2X3
7-685-134-19 SCREW (+ PTPWH) (2.6X8) 7-621-255-15 SCREW +P 2X3 7-685-871-01 SCREW +BVTT 3X6 (S)
Sony Corporation
9-960-872-11
Home A&V Products Company
-- 38 --
97B1694-1 Printed in Japan © 1997.2 Published by Service and Safety Engineering Dept. (Shibaura)