Text preview for : PMA-710AE.pdf part of DENON PMA-710ae Service Manual PMA-710ae



Back to : PMA-710AE.pdf | Home

Ver. 8
Please refer to the
MODIFICATION NOTICE.




SERVICE MANUAL
MODEL JP E3 E2 EK E2A E1C E1K EUT

PMA-710AE
INTEGRATED STEREO AMPLIFIER




For purposes of improvement, specifications and design are subject to change without notice.

Please use this service manual with referring to the operating instructions without fail.

Some illustrations using in this service manual are slightly different from the actual set.




e
D&M Holdings lnc.



S0279-0V08DM/DG1105 Copyright 2011 D&M Holdings Inc. All rights reserved.
WARNING: Violators will be prosecuted to the maximum extent possible.
SAFETY PRECAUTIONS
The following check should be performed for the continued protection of the customer and service technician.

LEAKAGE CURRENT CHECK
Before returning the unit to the customer, make sure you make either (1) a leakage current check or (2) a line to chassis
resistance check. If the leakage current exceeds 0.5 milliamps, or if the resistance from chassis to either side of the
power cord is less than 460 kohms, the unit is defective.



CAUTION Please heed the points listed below during servicing and inspection.

Heed the cautions! Inspect for safety after servicing!
Spots requiring particular attention when servicing, such Check that all screws, parts and wires removed or discon-
as the cabinet, parts, chassis, etc., have cautions indicated nected for servicing have been put back in their original po-
on labels or seals. Be sure to heed these cautions and the sitions, inspect that no parts around the area that has been
cautions indicated in the handling instructions. serviced have been negatively affected, conduct an insu-
lation check on the external metal connectors and between
Caution concerning electric shock! the blades of the power plug, and otherwise check that
safety is ensured.
(1) An AC voltage is impressed on this set, so touching in-
ternal metal parts when the set is energized could
(Insulation check procedure)
cause electric shock. Take care to avoid electric shock,
Unplug the power cord from the power outlet, disconnect
by for example using an isolating transformer and
the antenna, plugs, etc., and turn the power switch on. Us-
gloves when servicing while the set is energized, un-
ing a 500V insulation resistance tester, check that the in-
plugging the power cord when replacing parts, etc.
sulation resistance between the terminals of the power
(2)There are high voltage parts inside. Handle with extra plug and the externally exposed metal parts (antenna ter-
care when the set is energized. minal, headphones terminal, microphone terminal, input
terminal, etc.) is 1M or greater. If it is less, the set must
Caution concerning disassembly and be inspected and repaired.
assembly!
Though great care is taken when manufacturing parts from
sheet metal, there may in some rare cases be burrs on the
CAUTION Concerning important safety
edges of parts which could cause injury if fingers are
moved across them. Use gloves to protect your hands.
parts

Only use designated parts! Many of the electric and structural parts used in the set
have special safety properties. In most cases these prop-
The set's parts have specific safety properties (fire resis- erties are difficult to distinguish by sight, and using re-
tance, voltage resistance, etc.). For replacement parts, be placement parts with higher ratings (rated power and
sure to use parts which have the same properties. In par- withstand voltage) does not necessarily guarantee that
ticular, for the important safety parts that are marked z on safety performance will be preserved. Parts with safety
wiring diagrams and parts lists, be sure to use the desig- properties are indicated as shown below on the wiring dia-
nated parts. grams and parts lists is this service manual. Be sure to re-
place them with parts with the designated part number.
Be sure to mount parts and arrange
the wires as they were originally! (1) Schematic diagrams ... Indicated by the z mark.
For safety reasons, some parts use tape, tubes or other in- (2) Parts lists ... Indicated by the z mark.
sulating materials, and some parts are mounted away from
Using parts other than the designated
the surface of printed circuit boards. Care is also taken with
parts could result in electric shock, fires or
the positions of the wires inside and clamps are used to
other dangerous situations.
keep wires away from heating and high voltage parts, so
be sure to set everything back as it was originally.




2
PMA-710AE
DIMENSION




max
23
344




49
165.5

265
344




50.5

20.5
102.5
20




60

434




3
PMA-710AE
WIRE ARRANGEMENT
If wire bundles are untied or moved to perform adjustment or parts replacement etc.,be sure to rearrange them neatly as
they were originally bundled or placed afterward.
Otherwise, incorrect arrangement can be a cause of noise generation.



Wire arrangement viewed from the top


Front Panel side




Back Panel side




4
PMA-710AE
DISASSEMBLY
· Disassemble in order of the arrow of the figure of following flow.
· In the case of the re-assembling, assemble it in order of the reverse of the following flow.
· In the case of the re-assembling, observe "attention of assembling" it.

TOP CABINET



FRONT PANEL ASSY POWER PCB REAR PANEL
Refer to "DISASSEMBLY 1.FRONT PANEL ASSY" Refer to "EXPLODED VIEW" Refer to "EXPLODED VIEW"
and "EXPLODED VIEW" POWER PCB
FRONT PCB (Ref. No. of EXPLODED VIEW : 1-2)
(Ref. No. of EXPLODED VIEW : 2-1) MAIN PCB ASSY
FUNCTION PCB Refer to "EXPLODED VIEW"
(Ref. No. of EXPLODED VIEW : 2-3) POWER TRANSFORMER MAIN PCB ASSY
VOLUME PCB Refer to "EXPLODED VIEW" (Ref. No. of EXPLODED VIEW : 1-1)
(Ref. No. of EXPLODED VIEW : 2-4) POWER TRANSFORMER MCU PCB ASSY
SW/HP PCB (Ref. No. of EXPLODED VIEW : 28) (Ref. No. of EXPLODED VIEW : 2-2)
(Ref. No. of EXPLODED VIEW : 2-5)




About the photos used for descriptions in the "DISASSEMBLY" section.
· The direction from which the photographs used herein were photographed is indicated at "Direction of photograph: ***" at
the left of the respective photographs.
· Refer to the table below for a description of the direction in which the photos were taken.
· Photographs for which no direction is indicated were taken from above the product.




The viewpoint of each photograph
(Photografy direction)
View from above Front side




5
PMA-710AE
1. FRONT PANEL ASSY
Proceeding : CABINET TOP FRONT PANEL ASSY
(1) Remove the screws.




View from bottom




(2) Cut the wire clamp bands, then loose the style pins.

cut




Style pin : Loose




Disconnect the connector wires, then remove the screws.



CN55 CN50 CN94




CN94


CN93


CN51



CN52 CN53 CN95 CN92




Please refer to "EXPLODED VIEW" for the disassembly method of each P.W.B included in FRONT PANEL ASSY.




6
PMA-710AE
2. POWER PCB
Proceeding : TOP CABINET POWER PCB


Please refer to "EXPLODED VIEW" for the disassembly method in POWER PCB.




3. REAR PANEL
Proceeding : TOP CABINET REAR PANEL


Please refer to "EXPLODED VIEW" for the disassembly method in REAR PANEL.




4. MAIN PCB ASSY
Proceeding : TOP CABINET REAR PANEL MAIN PCB ASSY


Please refer to "EXPLODED VIEW" for the disassembly method in MAIN PCB ASSY.




5. POWER TRANSFORMER
Proceeding : TOP CABINET POWER TRANSFORMER


Please refer to "EXPLODED VIEW" for the disassembly method in POWER TRANSFORMAER.




7
PMA-710AE
EQ

SOURCE DIRECT
SPEAKER A
PHONO
TONE POWER AMP
35.5dB(MM)
& 44dB SPEAKER B
CD LOUDNESS
BUFFER MAIN VOLUME




INPUT
TUNER

BALANCE HEADPHONE
LINE
2

POWER AMP
1 4

PB OUTPUT STAGE
PRE OUT
3


REC
BLOCK AND LEVEL DIAGRAM




RECODER-1
PHONO EQ ±16V
VOLATAGE
PB
TONE ±16V
REGULATOR




8
POWER AMP ±16V AC CORD
REC
FIRST STAGE




RECODER-2
CONTROL




PMA-710AE
&
PREOUT RELAY

2


1 4

30dB 50W/8ohm 20.0V(25.5dB)
STANDBY 3

20dB


10dB

0.7V/10k ohm(-3dB)
0dB


-10dB
CD etc. 100mV(-20dB)
-20dB

-30dB

-40dB

-50dB
MM 1.7mV(-55.4dB)
-60dB

-70dB
ADJUSTMENT
Idling Current
Required measurement equipment: DC Voltmeter
1. Setup
(1) Place the unit at an ordinary position avoiding direct air flow from an air-conditioner or fan. Do the adjustment at a tem-
perature between 15 °C (59 °F) and 30 °C (86 °F).
(2) Set control as follows.
· POWER switch OFF (j).
· VOLUME control fully counterclockwise ( c min.)
· SPEAKER terminals open: do not connect the speakers, dummy load etc.
2. Adjustment
(1) Remove top cover. And then connect DC Voltmeter to the test points CN31 and CN32 of CUP12196B Main PCB.
(2) Connect power cord to AC wall outlet, and turn POWER switch "ON" ( h ).
(3) Right after power on, adjust VR31 and VR32 so that the DC voltmeter reads 10 ±1mV.
(4) Then after 2 minutes warm up adjust VR31 and VR32 so that the DC voltmeter reads 10 ±1mV.
(5) And after 10 minutes warm up adjust VR31 and VR32 so that the DC voltmeter reads 10 ±0.5mV.




DC Voltmeter




CN31

VR31




Power
Trans
VR32

CN32




Volume




9
PMA-710AE
TROUBLE SHOOTING
1. The power can not be turned on. (Power indication LED does not light.)
Check the insertion of the Power Part.




Check whether power is being supplied to the coil Broken wire in standby trans-
Power not supplied.
of the standby transformer (T901). former (T901)




Malfunction of D941-944, C941
Power supplied.
or C943.




2. The power turned on, but a sound does not output normally. (Both channels)
2.1.
Set remains in standby mode with power indicator
LED lit red.




The connectors are inserted
Check each connector. Malfunction of RC71 or IC41.
completely.



2.2.
Power indicator LED remains flashing red and
muting mode is not canceled (protection mode is
set).




Offset voltage output is 1V or Damaged power amplifier cir-
Check the power amplifier output's offset voltage.
greater. cuit.



Damaged temperature detec-
No offset voltage is output.
tion circuit or protection circuit.




2.3.
Set operates, but then power indicator LED
flashes red (protection mode is set).




Offset voltage output is 1V or Damaged power amplifier cir-
Check the power amplifier output's offset voltage.
greater. cuit.




No offset voltage is output. Check the bias current.




10
PMA-710AE
2.4.
Power indicator LED is lit normally (green or
Check each connector.
orange).




Is the fuse (F901) normal?




Check the voltage of each
department.




Check the operation of the
switching relay, switching IC
and speaker relay.




Check the Signal line.




3. The power turned on, but a sound does not output normally. (Single channel)
Power indicator LED is lit normally (green or
Check each connector.
orange).




Check the voltage of each
department.




Check the operation of the
switching relay, switching IC
and speaker relay.




Check the Signal line.




11
PMA-710AE
SEMICONDUCTORS
Only major semiconductors are shown, general semiconductors etc. are omitted to list.
The semiconductor which described a detailed drawing in a schematic diagram are omitted to list.


1. IC's
TMP86FH47AUG (IC41)




TMP86FH47AUG Terminal Function
Pin No. Port Name I/O Function
1 VSS VSS
2 XIN X IN
3 XOUT X OUT
4 TEST TEST
5 VDD VDD
6 P21 XTIN O MUTE/STANDBY LED
7 P22 XTOUT O
8 RESET I RESET
9 P20 INT5 STOP I STOP ACT.
10 P00 INT0 I PROTECTOR
11 P01 PDO4/PWM4/PPG4 TC4 O P. DIRECT RELAY
12 P02 RXD I RXD
13 P03 TXD O TXD
14 P04 SO O DATA
15 P05 SI O STROBE
16 P06 SCK O CLK
17 P07 INT4 O S. DIRECT RELAY
18 P17 I P. DIRECT SW
19 P16 I S. DIRECT SW
20 P15 INT3 AC RELAY 1
21 P14 PPG O VOLUME UP
22 P13 DVO O VOLUME DOWN
23 P12 INT2 TC1 I REMOTE IN
24 P11 INT1 I POWER OFF
25 P10 PDO3/PWM3 TC3 AC RELAY 2
26 P30 AIN0 AI MODEL


12
PMA-710AE
Pin No. Port Name I/O Function
27 P31 AIN1 AI SP A/B
28 P32 AIN2 AI REC. SEL
29 P33 AIN3 AI FUNC. SEL
30 P34 AIN4 STOP2 O H/P MUTE
31 P35 AIN5 STOP3 O SP A
32 P36 AIN6 STOP4 O SP B
33 P37 AIN7 STOP5
34 VAREF Vref
35 AVDD AVDD
36 AVSS AVSS
37 P40 O PHONO
38 P41 O CD
39 P42 O TUNER
40 P43 O AUX-1
41 P44 O AUX-2
42 P45 O AUX-3
43 P46 O TAPE-1
44 P47 O TAPE-2




TC9164AN (IC22)

TC9164AN
VSS GND VDD
1 14 28
VSS 1 28 VDD L-S1 2 27 R-S1
L-S1 2 27 R-S1
L-S2 3 26 R-S2
L-S2 3 26 R-S2
L-S3 4 25 R-S3 L-S3 4 25 R-S3
L-S4 5 24 R-S4
L-S4 5 24 R-S4
L-COM1 6 23 R-COM1
Level Shifter




Latch Circuit



Level Shifter
Latch Circuit




L-S5 7 R-S5 L-COM1 6 23 R-COM1
22
L-S6 8 21 R-S6 L-S5 7 22 R-S5
L-COM2 9 20 R-COM2 L-S6 8 21 R-S6
L-S7 10 19 R-S7
L-COM2 9 20 R-COM2
L-S8 11 18 R-S8
L-COM3 12 17 R-COM3 L-S7 10 19 R-S7
ST 13 16 DATA
L-S8 11 18 R-S8
GND 14 15 CK
L-COM3 12 17 R-COM3

ST 13 16 DATA
15 CK
Shift Register




TC9163AN (IC21)

TC9163AN VSS GND VDD
1 14 28
VSS 1 28 VDD L-S1 2 27 R-S1
L-S1 2 27 R-S1
L-S2 3 26 R-S2
L-S2 3 26 R-S2
L-S3 4 25 R-S3 L-S3 4 25 R-S3
L-COM1 5 24 R-COM1 24 R-COM1
L-COM1 5
L-S4 6 23 R-S4
Level Shifter




Latch Circuit



Level Shifter
Latch Circuit




L-S5 7 R-S5 L-S4 6 23 R-S4
22
L-S6 8 21 R-S6 L-S5 7 22 R-S5
L-COM2 9 20 R-COM2 L-S6 8 21 R-S6
L-S7 10 19 R-S7
L-COM2 9 20 R-COM2
L-S8 11 18 R-S8
L-COM3 12 17 R-COM3 L-S7 10 19 R-S7
ST 13 16 DATA
L-S8 11 18 R-S8
GND 14 15 CK
L-COM3 12 17 R-COM3

ST 13 16 DATA
15 CK
Shift Register




13
PMA-710AE
---MEMO---




14
PMA-710AE
PRINTED WIRING BOARDS
MAIN PCB ASSY (1/2)




COMPONENT SIDE



15
PMA-710AE
MAIN PCB ASSY (2/2)




FOIL SIDE




16
PMA-710AE
FRONT PCB ASSY (1/2)




COMPONENT SIDE


17
PMA-710AE
FRONT PCB ASSY (2/2)




FOIL SIDE




18
PMA-710AE
NOTE FOR PARTS LIST
1. Parts for which "nsp" is indicated on this table cannot be supplied.

2. When ordering of part, clearly indicate "1" and "I" (i) to avoid mis-supplying.

3. Ordering part without stating its part number can not be supplied.

4. Part indicated with the mark " " is not illustrated in the exploded view.

5. Not including General-purpose Carbon Film Resistor in the P.W.Board parts list. (Refer to the Schematic Diagram for those parts.)

6. Not including General-purpose Carbon Chip Resistor in the P.W.Board parts list. (Refer to the Schematic Diagram for those parts.)
WARNING:
Parts marked with this symbol z have critical characteristics.
Use ONLY replacement parts recommended by the manufacturer.

Resistors
Ex.: RN 14K 2E 182 G FR

Type Shape Power Resist- Allowable Others
and per- ance error
formance

RD : Carbon 2B : 1/8 W F : 1% P : Pulse-resistant type
RC : Composition 2E : 1/4 W G : 2% NL : Low noise type
RS : Metal oxide film 2H : 1/2 W J : 5% NB : Non-burning type
RW: winding 3A : 1 W K : 10% FR : Fuse-resistor
RN : Metal film 3D : 2 W M : 20% F : Lead wire forming
RK : Metal mixture 3F : 3 W
3H : 5 W

Resistance

1 8 2 1800ohm=1.8kohm

Indicates number of zeros after effective number.
2-digit effective number.

1 R 2 1.2ohm

1-digit effective number.
2-digit effective number, decimal point indicated by R.
: Units: ohm

Capacitors

Ex.: CE 04W 1H 3R2 M BP

Type Shape Dielectric Capacity Allowable Others
and per- strength error
formance

CE : Aluminum foil 0J : 6.3 V F : 1% HS : High stability type
electrolytic 1A : 10 V G : 2% BP : Non-polar type
CA : Aluminium solid 1C : 16 V J : 5% HR : Ripple-resistant type
electrolytic 1E : 25 V K : 10% DL : For change and discharge
CS : Tantalum electrolytic 1V : 35 V M : 20% HF : For assuring high requency
CQ : Film 1H : 50 V Z : 80% U : UL part
CK : Ceramic 2A : 100 V : - 20% C : CSA part
CC : Ceramic 2B : 125 V P : +100% W : UL-CSA part
CP : Oil 2C : 160 V C : 0.25pF F : Lead wire forming
CM: Mica 2D : 200 V D : 0.5pF
CF : Metallized 2E : 250 V = : Others
CH : Metallized 2H : 500 V
2J : 630 V

Capacity (electrolyte only)

2 2 2 2200 F 2 R 2 2.2 F

Indicates number of zeros after effective number. 1-digit effective number.

2-digit effective number. 2-digit effective number, decimal point indicated by R
Units: F. Units: F.


Capacity (except electrolyte)

2 2 2 2200pF=0.0022 F 2 2 1 220pF

Indicates number of zeros after efective number. Indicates number of zeros after effective numver.
(More than 2) (0 or 1)

2-digit effective number. 2-digit effective number.
Units:pF Units:pF

When the dielectric strength is indicated in AC,"AC" is included after the dieelectric strength value.



19
PMA-710AE
PARTS LIST OF PCB UNIT
Parts for which "nsp" is indicated on this table cannot be supplied.
The parts listed below are for maintenance only, might differ from the parts used in the unit in appearances or dimensions.
Note: The symbols in the column "Remarks" indicate the following destinations.
E2 : Europe model E1C : China model


MAIN PCB UNIT ASS'Y
Ref No. Part No. Part Name Remark Q'ty New
SEMICONDUCTORS GROUP
IC10 00D9430198207 IC NJM2068DD HVINJM2068DD 1
IC21 00D2622487009 IC TC9163AN CVITC9163AN 1
IC22 00D9430198401 IC TC9164AN HVITC9164AN 1
IC91 00D2631100021 IC KIA7812API-U/P HVIKIA7812API 1 d
IC92 00D2631100018 IC KIA7806API-U/P HVIKIA7806API 1 d

Q215,216 00D9430107804 TR KRC102M HVTKRC102MT 2
Q251,252 00D9430154404 TR KTC3198Y HVTKTC3198YT 2
Q253 90M-HT600010R TR KTA1266Y HVTKTA1266YT 1
Q254 00D9430154200 TR KRA102M HVTKRA102MT 1
Q255,256 00D9430154404 TR KTC3198Y HVTKTC3198YT 2
Q301-304 00D9430198906 TR KTC3200GR HVTKT3200GRT 4
Q307-310 00D9430198906 TR KTC3200GR HVTKT3200GRT 4
Q311-314 00D9430198702 TR KTA1024Y HVTKTA1024YT 4
Q315,316 00D9430199002 TR KTC3206YA HVTKTC3206YAT 2
Q317,318 943219005820S TR 2SC4495 FM20 CVT2SC4495 2
Q319,320 00D9430200700 TR 2SD2083P CVT2SD2083P-OKM 2
Q321,322 00D9430197004 TR 2SD1383P CVT2SB1383P-OKM 2
Q323,324 00D9430198906 TR KTC3200GR HVTKT3200GRT 2
Q325 00D9430006206 TR KTA1268GR HVTKA1268GRT 1
Q330 00D9430107804 TR KRC102M HVTKRC102MT 1
Q901 00D2720164004 TR KTD2058Y HVTKTD2058Y 1
Q902 00D2740202001 TR KTB1366Y HVTKTB1366Y 1


D215,216 00D9430182609 DIODE 1SS133 HVD1SS133MT 2
D221,222 00D9430182609 DIODE 1SS133 HVD1SS133MT 2
D309,310 00D9430196102 DIODE , ZENER MTZJ3.3B 1/2W HVDMTZJ3.3BT 2
D311,312 00D9430182609 DIODE 1SS133 HVD1SS133MT 2
D313,314 00D9430196102 DIODE , ZENER MTZJ3.3B 1/2W HVDMTZJ3.3BT 2
D315,316 00D9430182609 DIODE 1SS133 HVD1SS133MT 2
D328-332 00D9430182609 DIODE 1SS133 HVD1SS133MT 5
D363,364 00D9430182609 DIODE 1SS133 HVD1SS133MT 2
D901 943203003140S DIODE FCH20A20 CVDFCH20A20 1
D902 943203004970S DIODE FRH20A20 CVDFRH20A20 1
D903,904 00D9430195909 ZENER DIODE ZJ16B HVDMTZJ16BT 2
D909,910 00D9430182502 DIODE 1N4003 CVD1N4003ST 2
D921-924 00D9430182502 DIODE 1N4003 CVD1N4003ST 4
D941-946 00D9430182502 DIODE 1N4003 CVD1N4003ST 6
D951,952 00D9430182609 DIODE 1SS133 HVD1SS133MT 2


RESISTORS GROUP
R313,314 nsp METAL OXIDE RES 3900 ohm 1W J KRG1SANJ392RT 2
R345-348 00MGG05033160 CARBON FILM RES 3.3ohm 1/4W J NB - 4 h
R349-356 nsp METAL OXIDE RES 0.47 ohm 2W J KRG2SANJR47RT 8
R373,374 nsp METAL OXIDE RES 10 ohm 1W J KRG1SANJ100RT 2
R381,382 nsp METAL OXIDE RES 390 ohm 1W J KRG1SANJ391RT 2
R901,902 00MGG05010160 CARBON FILM RES 1ohm 1/4W J NB - 2 h
R921,922 00MGG05010160 CARBON FILM RES 1ohm 1/4W J NB - 2 h
R923 00D9430194308 RES. FUSE 0.3ohm 1/6W K CRQ16AKR30T 1 h
R924,925 nsp METAL OXIDE RES 68 ohm 1W J KRG1SANJ680RT 2 h
R929 00MGG05022140 CARBON FILM RES 2.2ohm 1/4W J NB - 1 h

VR31,32 00D9430196908 SEMI FIXED RESISTOR 500 ohm CVN1GE501B01T 2

20
PMA-710AE
Ref No. Part No. Part Name Remark Q'ty New
CAPACITORS GROUP
C101-104 nsp CERAMIC CAP 100pF 50V KB CCKT1H101KB 4
C105,106 nsp ELECT CAP 10uF 50V CCEA1HH100T 2
C109,110 nsp ELECT CAP 220uF 50V CCEA1CH221T 2
C111,112 nsp MYLAR CAP 6800pF 50V J HCQI1H682JZT 2
C113,114 nsp MYLAR CAP 0.018pF 50V J HCQI1H183JZT 2
C115,116 nsp MYLAR CAP 6800pF 50V J HCQI1H682JZT 2
C117,118 nsp ELECT CAP 10uF 50V CCEA1HH100T 2
C119,120 nsp MYLAR CAP 3900pF 50V J HCQI1H392JZT 2
C121,122 00D2544569924 ELECT CAP RA3-25V 101MF3 CCEA1ERA38P101T 2
C209,210 nsp CERAMIC CAP 100PF 50V K CCKT1H101KB 2
C213,214 nsp CERAMIC CAP 100PF 50V K CCKT1H101KB 2
C215,216 00D2544702956 ELECT CAP RFS-50V 100MG3 CCEA1HRFSA100E 2
C220 00D2544573994 ELECT CAP RA3-50V 220ME3 CCEA1HRA38P220T 1
C221 00D2544569924 ELECT CAP RA3-25V 101MF3 CCEA1ERA38P101T 1
C223 00D2544569924 ELECT CAP RA3-25V 101MF3 CCEA1ERA38P101T 1
C251 nsp ELECT CAP 33UF 50V CCEA1HH330T 1
C252 nsp CEMICONDUCTOR CAP 0.022uF 50VZF CCFT1H223ZF 1
C254 nsp CEMICONDUCTOR CAP 0.047uF 50VZF CCFT1H473ZF 1
C256 nsp ELECT CAP 47uF 25V CCEA1EH470T 1
C258 943134006150S ELECT CAP RA3-10V 471MG3 CCEA1ARA38P471T 1
C301,302 00D2544703751 ELECT CAP RFS-50V 220MH3 CCEA1HRFSA220E 2
C303,304 nsp CERAMIC CAP 220PF 50V K CCKT1H221KB 2
C305,306 nsp CERAMIC CAP 100pF 50V K CCKT1H101KB 2
C307,308 nsp CERAMIC CAP 1000pF 50V K CCKT1H102KB 2
C309-312 00D2544774719 ELECT CAP RFS-25V 221MI5 CCEA1ERFSA221E 4
C319-322 nsp MYLAR CAP 3900pF 50V J HCQI1H392JZT 4
C323,324 00D2544703777 ELECT CAP RFS-50V 470MH4 CCEA1HRFSA470T 2
C325,326 nsp CERAMIC CAP 22PF 50V J CCCT1H220JC 2
C327,328 nsp CERAMIC CAP 1000PF 50V K CCKT1H102KB 2
C329,330 00D2544703777 ELECT CAP RFS-50V 470MH4 CCEA1HRFSA470T 2
C331,332 00D2544702956 ELECT CAP RFS-50V 100MG3 CCEA1HRFSA100E 2
C341,342 nsp CERAMIC CAP 33PF 50V J CCCT1H330JC 2
C367 nsp ELECT CAP 4.7uF 50V CCEA1HH4R7T 1
C373,374 nsp MYLAR CAP 0.1UF 50V J HCQI1H104JZT 2
C375-378 nsp MYLAR CAP 0.047upF 50V J E2 HCQI1H473JZT 4
C379,380 nsp CERAMIC CAP 0.01UF/50V E2 CCKT1H103KB 2
C383,384 00D2544569924 ELECT CAP RA3-25V 101MF3 CCEA1ERA38P101T 2
C901,902 00D2546262009 ELECT CAP LAO-56V 822MS49WP CCET56VLAO822NZ 2
C903,904 nsp METALLIZED CAP 0.1uF 250V J KCME2E104JP04T 2
C907,908 00D2544702956 ELECT CAP RFS-50V 100MG3 CCEA1HRFSA100E 2
C909,910 00D2544664706 ELECT CAP RFS-63V 101MI6 CCEA1JRFSA101E 2
C921,922 nsp CERAMIC CAP 0.01uF 50V Z CCFT1H103ZF 2
C923 nsp ELECT CAP 1000uF 25V CCEA1EH102E 1
C924 nsp ELECT CAP 0.47uF 50V CCEA1HHR47T 1
C925-928 nsp CEMICONDUCTOR CAP 0.1uF 50VZF CCFT1H104ZF 4
C929,930 00D2544569911 ELECT CAP RA3-25V 470ME3 CCEA1ERA38P470T 2
C941 nsp ELECT CAP 1000uF 25V CCEA1EH102T 1
C942 nsp ELECT CAP 0.47uF 50V CCEA1HHR47T 1
C943 nsp CERAMIC CAP 0.01uF 50V Z CCFT1H103ZF 1
C944 nsp CEMICONDUCTOR CAP 0.1uF 50VZF CCFT1H104ZF 1
C951,952 nsp CERAMIC CAP 0.0047uF 2.5KV KCKDKS472ME 2



OTHERS PARTS GROUP
BK91 nsp PCB BRACKET (A) CMD1A188 1
BN91 nsp WIRE ASSY(2P, 300MM, 7.9MM) CWB4DA32300UZ 1


CN31,32 nsp WAFER 3PIN 2MM CJP03GA01ZY 2
CN51 nsp STRAIGHT WAFER 7PIN 2MM CJP07GI236ZW 1
CN52 nsp STRAIGHT WAFER 7PIN 2.5MM CJP07GI237ZW 1


21
PMA-710AE
Ref No. Part No. Part Name Remark Q'ty New
CN53 nsp STRAIGHT WAFER 7PIN 2MM CJP07GI236ZW 1
CN54 nsp WAFER 13PIN 2MM BMW200 CJP13GA98ZY 1
CN90 nsp WAFER 2PIN 2MM CJP02KA060ZY 1
CN91 nsp WAFER 2PIN 2MM CJP02GA89M 1
CN92 nsp STRAIGHT WAFER 5PIN 2MM CJP05GI236ZW 1
CN93 nsp STRAIGHT WAFER 3PIN 2.5MM CJP03GI237ZW 1
CN95 nsp STRAIGHT WAFER 3PIN CJP03GA90ZY 1


z F901 00D9430199109 FUSE 2.5A 250V E2 KBA2C2500TLEY 1
z F901 00D9430199109 FUSE 2.5A 250V E1C KBA2C2500TLEY 1
z F902 00D9430199109 FUSE 2.5A 250V E2 KBA2C2500TLEY 1


JK11 00D9430191700 2P JACK,IN/OUT CJJ4N034Z 1
JK21-24 00D9430191807 4P JACK,IN/OUT CJJ4P028Z 4
JK31 00D9430191904 SPEAKER TERMINAL CJJ5Q006Z 1


L101,102 00D9430193601 TOROIDAL COIL CLU9S004Z 2


OL91 943641005850S AC OUTLET JACK (230V , 3P) E2 CJJ7A031Z 1 *


RY31 00D9430195103 RELAY G5V-2-H1 CSL4A015ZU 1
RY32,33 00D9430195006 RELAY G5PA-28 CSL3A018ZE 2
RY51,52 00D9430195103 RELAY G5V-2-H1 CSL4A015ZU 2
RY91 00D9430200807 POWER RERAY G2R-14 CSL2C002ZE 1
RY92 00D9430194900 POWER RERAY G5PA-1 CSL1E002ZE 1


TH09 00D9430194609 POSISTOR PTFM04BB222QN34 CRTPTFM04BB222Q 1
TH51 00D9430194502 THERMISTOR ASSY(170MM) CRT0217025MM 1


z T901 00D9430193203 SUB TRANSFORMER E2 CLT5I008ZE 1
z T901 943101005870S SUB TRANSFORMER E1C CLT5I008ZH 1 *


nsp HFUSE HOLDER KJCFC5S 4
nsp HEAT SINK CMY2A048 3
nsp SCREW 3X8 CTB3+8JR 3




22
PMA-710AE
FRONT PCB UNIT ASS'Y
Ref No. Part No. Part Name Remark Q'ty New
SEMICONDUCTORS GROUP
IC41 943243100670D CVIANAM1468A MICOM PMA510AE IC U-COM PMA510AE 1 *
(CVITMP86FH47BUG)
jk
IC42 00D9430196500 IC LB1930M CVILB1930M 1
IC43 00D9430038902 IC KIA1117S/F33, SOT-223 CVIKIA1117S33 1
IC52 00D9430198207 IC NJM2068DD HVINJM2068DD 1

Q408 00D9430037903 CHIP TR KRC102S HVTKRC102S 1
Q449,450 00D9430037903 CHIP TR KRC102S HVTKRC102S 2
Q451 00D9430072502 CHIP TR KTC2875B HVTKTC2875B 1
Q452,453 00D9430037903 CHIP TR KRC102S HVTKRC102S 2
Q454-457 00D9430072502 CHIP TR KTC2875B HVTKTC2875B 4
Q464 00D9430037903 CHIP TR KRC102S HVTKRC102S 1
Q465-467 00D9430038009 CHIP TR KRA102S HVTKRA102S 3
Q468 00D9430072502 CHIP TR KTC2875B HVTKTC2875B 1
Q469 00D9430037903 CHIP TR KRC102S HVTKRC102S 1
Q472,473 00D9430037903 CHIP TR KRC102S HVTKRC102S 2
Q474 00D9430038009 CHIP TR KRA102S HVTKRA102S 1
Q562,563 00D9430038009 CHIP TR KRA102S HVTKRA102S 2
Q564,565 00D9430037903 CHIP TR KRC102S HVTKRC102S 2
Q571-576 00D9430037903 CHIP TR KRC102S HVTKRC102S 6
Q582,583 00D9430038009 CHIP TR KRA102S HVTKRA102S 2

D401,402 90M-HD201840R DIODE 1SR159 HVD1SR159-200 2
D403 00D9430182502 DIODE 1N4003 CVD1N4003T 1
D404 90M-HD201840R DIODE 1SR159 HVD1SR159-200 1
D405 00D9430182502 DIODE 1N4003 CVD1N4003T 1
D406,407 90M-HD201840R DIODE 1SR159 HVD1SR159-200 2
D408 90M-HD302310R ZENER DIODE MTZJ27B HVDMTZJ27BT 1
D409 943202005890S ZENER DIODE MTZJ9.1B HVDMTZJ9.1BT 1
D421,422 90M-HD201840R RECTIFIER DIODE 1SR159 HVD1SR159-200 2
D458 90M-HZ200190R SWITCHING DIODE RSL4148 HVDRLS4148SR 1
D461 90M-HZ200190R SWITCHING DIODE RSL4148 HVDRLS4148SR 1
D464 90M-HZ200190R SWITCHING DIODE RSL4148 HVDRLS4148SR 1
D468 00D9430196306 ZENER DIODE MTZJ7.5B HVDMTZJ7.5BT 1
D469 00D9430196209 ZENER DIODE MTZJ4.7B HVDMTZJ4.7BT 1
D501 00D9430198100 2 COLOR LED SML1216W HVDSML1216W 1
D551 943209001080S CHIP DIODE 1SS355 CVD1SS355T 1
D553 943209001080S CHIP DIODE 1SS355 CVD1SS355T 1
D555 943209001080S CHIP DIODE 1SS355 CVD1SS355T 1
D557 943209001080S CHIP DIODE 1SS355 CVD1SS355T 1
D559 943209001080S CHIP DIODE 1SS355 CVD1SS355T 1
D561 943209001080S CHIP DIODE 1SS355 CVD1SS355T 1
D571-576 00D9430195705 LED, ORANGE TITNED SEL2915A CVDSEL2915A 6
D661-672 943209001080S CHIP DIODE 1SS355 CVD1SS355T 12

RESISTORS GROUP
VR51 00D9430197305 MOTOR VR CVV9Y13B503Z 1
VR52 00D9430197101 VARIABLE RES RA1450GOE0D-HA1 CVV2X13M104Z 1
VR53 00D9430197208 TONE VR D103-Q1-FB200B1 CVV2X18D103Z 1
VR54 00D9430215504 TONE VR D303-Q1-FB200B1 CVV2X19D303Z 1
VR55 943663005900S ROTARY SW CSR6A001Z 1
VR56 00D9430195200 ROTARY SW CSRCA001Z 1

CAPACITORS GROUP
C401 nsp ELECT CAP 100uF 16V CCEA1CH101T 1
C402 nsp CHIP CAP 0.01uF 50V CCUS1H103KC 1
C403 nsp ELECT CAP 100uF 16V CCEA1CH101T 1
C404 nsp CHIP CAP 0.01uF 50V CCUS1H103KC 1
C405 nsp ELECT CAP 3300uF 16V CCEA1CH332E 1
C406 nsp ELECT CAP 22uF 50V CCEA1HH220T 1

23
PMA-710AE
Ref No. Part No. Part Name Remark Q'ty New
C407,408 nsp CHIP CAP 0.01uF 50V CCUS1H103KC 2
C421 nsp ELECT CAP 10uF 50V CCEA1HH100T 1
C445 nsp CHIP CAP 0.1uF 50V CCUS1H104KC 1
C458 nsp ELECT CAP 2.2uF 50V CCEA1HH2R2T 1
C461 nsp CHIP CAP 0.01uF 50V CCUS1H103KC 1
C464 nsp ELECT CAP 1uF 50V CCEA1HH1R0T 1
C465 nsp ELECT CAP 10uF 50V CCEA1HH100T 1
C466 nsp ELECT CAP 470uF 10V CCEA1AH471T 1
C481,482 nsp CERAMIC CAP 1000pF 50V CCKT1H102KB 2
C486-489 nsp CHIP CAP 0.01uF 50V CCUS1H103KC 4
C503,504 nsp ELECT CAP 4.7uF 50V CCEA1HH4R7T 2
C505,506 00D2544569924 ELECT CAP RA3-25V 101MF3 CCEA1ERA38P101T 2
C507,508 nsp ELECT CAP 10uF 50V CCEA1HH100T 2
C509,510 nsp MYLAR CAP 0.033uF 50V HCQI1H333JZT 2
C513,514 nsp ELECT CAP 0.22uF 50V CCEA1HHR22T 2
C519,520 nsp ELECT CAP 0.1uF 50V CCEA1HH0R1T 2
C521,522 nsp ELECT CAP 0.47uF 50V CCEA1HHR47T 2
C533,534 nsp MYLAR CAP 0.047uF 50V HCQI1H473JZT 2
C535,536 nsp ELECT CAP 0.47uF 50V CCEA1HHR47T 2
C537,538 nsp MYLAR CAP 0.033uF 50V HCQI1H333JZT 2
C539,540 nsp CERAMIC CAP 39pF 50V CCCT1H390JC 2
C541,542 nsp MYLAR CAP 3300pF 50V HCQI1H332JZT 2
C563 nsp CHIP CAP 0.01uF 50V CCUS1H103KC 1
C565 nsp ELECT CAP 100uF 10V CCEA1AH101T 1
C566 nsp CHIP CAP 0.1uF 50V CCUS1H104KC 1
C583 nsp CHIP CAP 0.01uF 50V CCUS1H103KC 1
C591 nsp ELECT CAP 22uF 16V