Text preview for : Sony RS-232 Protcol Manual.pdf part of SONY FWD-40LX2F RS-232 Protocol Manual 1st Edition. FWD-40LX2F/X, FWD-32LX2F/X, KLH-W32/26
Back to : Sony RS-232 Protcol Manua | Home
FLAT WIDE DISPLAY MONITOR
FWD-40LX2F FWD-40LX2X FWD-32LX2F FWD-32LX2X KLH-W32 KLH-W26
PROTOCOL MANUAL 1st Edition
Table of Contents
1. Communication Parameters .......................................................... 1 2. Pin Assignment ...................................................................................... 1 3. Communication Data Format ......................................................... 1 4. General Function ................................................................................... 3 5. Picture/Sound ........................................................................................ 11 6. Size/Shift .................................................................................................. 13 7. Status Enquiry ....................................................................................... 16 8. User Reset ............................................................................................... 20 9. Service ........................................................................................................ 20
FWD-40LX2F/40LX2X/32LX2F/32LX2X KLH-W32/W26
1. Communication Parameters
Communication Method Synchronous Method Baud Rate Character Length Parity Start Bit Length Stop Bit Length Flow Control RS-232C Asynchronous 9600 bps 8bit None 1bit 1bit None
3. Communication Data Format
(a) Control message
No. 1 2 3 4 5 : : Item Header Category Function Data1 (Length) Data2 (Data1) : : Data (X-3) Check Sum Value 0x8C:Control 0xXX 0xXX 0xXX 0xXX 0xXX 0xXX 0xXX 0xXX
2. Pin Assignment
Monitor side : D-sub Host side : D-sub 9pin
X X+1
* Check Sum: Sum total of 1 to X. Lower one-byte data is validated when a value exceeds 255 (1byte). * Set the command interval to 500 ms or more when transmitting the Control command continuously. * Set the command interval to 500 ms or more when transmitting the same command (Enquiry) after the Control command.
(b) Enquiry message
FWD-40LX2F/40LX2X FWD-32LX2F/32LX2X
5 9 4 8 3 7 2 6 1
Personal computer No. 1
5 9 4 8 3 7 2 6 1
Item Header Category Function Data1 Data2 Check Sum
Value 0x83:Enquiry 0xXX 0xXX 0xFF 0xFF 0xXX
2 3
_ External view _ Pin No. 1 2 3 4 5 6 7 8 9 Signal NC RXD TXD NC GND NC NC NC NC
_ External view _ Pin No. 1 2 3 4 5 6 7 8 9 Signal NC RXD TXD NC GND NC NC NC NC
4 5 6
* Check Sum: Sum total of 1 to 5. Lower one-byte data is validated when a value exceeds 255 (1byte).
The control command is not acceptable for 3 seconds after the power is turned on from the standby state and for 5 seconds after the power is turned on when AC is set to ON from OFF state. Send the command after waiting each required time. In the case when the power is turned on from the standby state, the starting up by using the timer (KLH-W26/W32 does not have this function), the power key of main unit or the remote commander is included as well as the command from RS-232C.
FWD-40LX2F/40LX2X/32LX2F/32LX2X KLH-W32/W26
1
(c) Answer message 1 Control answer
No. 1 2 Item Header Answer
*
4 Error answer
No. Item 1 2 Header Answer* Value 0xE0:Answer 0x00:No Function Error 0x01:Check Sum Error 0x02:Data Length Error 3 Check Sum 0xXX
Value 0x70:Answer 0x00:Completed 0x01:Limit Over 0x02:Limit Under 0x03:Command Canceled
3
Check Sum
0xXX
Packet is correctly received and process is also correctly completed. Packet is correctly received, but the data value is over the upper limit. Packet is correctly received, but the data value under the lower limit. Packet is correctly received, but the data value is not correct or the request cannot be accepted in the current host state. Sum total of 1 to 2. Lower one-byte data is validated when a value exceeds 255 (1byte).
* 0x00:Completed 0x01:Limit Over 0x02:Limit Under 0x03:Command Canceled
* 0x00:No Function Error Packet header, category of function code are not included in this protocol. 0x01:Check Sum Error Check sum value of received packet is not correct. 0x02:Data Length Error Packet is correctly received, but the data size is over the upper limit. * Check Sum: Sum total of 1 to 2. Lower one-byte data is validated when a value exceeds 255 (1byte).
* Check Sum:
2 Enquiry answer (Complete)
No. Item 1 2 3 4 : : X Header Answer Value 0x70:Answer 0x00:Completed
Return Data Size 0xXX Return Data1 : : 0xXX 0xXX 0xXX
Return Data (X-3) 0xXX 0xXX
X+1 Check Sum
* 0x00:Completed * Return Data: * Check Sum:
Packet is correctly received and process is also correctly completed. Returns the read value. Sum total of 1 to X. Lower one-byte data is validated when a value exceeds 255 (1byte).
3 Enquiry answer (Command cancel)
No. Item 1 2 3 Header Answer Check Sum Value 0x70:Answer 0x03:Command Canceled 0x73
Packet is correctly received, but the data value is not correct of the request cannot be accepted in the current host state.
0x03:Command Canceled
2
FWD-40LX2F/40LX2X/32LX2F/32LX2X KLH-W32/W26
4. General Function
(a) Mode Control
Syntax Control Enquiry Header 0x8C 0x83 Category 0x00 Function Code Table (1-a)[a] Data1 0x02 0xFF Data2 Code Table (1-a)[b] 0xFF Check Sum 0xXX 0xXX
Answer Control
Header 0x70 0x70 0x70 0x70
Answer 0x00 0x01 0x02 0x03
Check Sum 0x70 0x71 0x72 0x73 Completed Limit Over Limit Under Command Canceled
Answer Enquiry
Header 0x70
Answer 0x00
Return to Data Size 0x02
Return Data1 Code Table(1-a)[b]
Check Sum 0xXX Completed
Code Table (1-a)
[a]Function 0x00 Power
*1
[b]Range/Switch Code 0x00 0x01 OFF ON INPUT1 RGB (Analog) INPUT1 YUV (Analog) OPTION1 VIDEO OPTION1 S-VIDEO OPTION1 RGB OPTION1 COMPONENT OPTION2 VIDEO*2 OPTION2 S-VIDEO*2 OPTION2 RGB*2 OPTION2 COMPONENT*2 INPUT2 RGB (Digital) INPUT2 DTV (Digital) INPUT3 RGB (Digital) INPUT3 DTV (Digital) ON OFF OFF ON ON OFF
Command Control Yes
Enquiry Yes
Standby Enable
Power On Enable
0x01
Input Select*3
0x08 0x09 0x0C 0x0D 0x0E 0x0F 0x10 0x11 0x12 0x13 0x44 0x45 0x54 0x55
Yes
Yes
Disable
Enable
0x02
Force Status Display
0x00 0x01
Yes
Yes
Disable
Enable
0x03
Audio Mute
0x00 0x01
Yes
Yes
Disable
Enable
0x04
Auto Status Display
0x00 0x01
Yes
Yes
Enable
Enable
0x10 0x14
Index Number Speaker Out
0x01-0xFF 0x00 0x01 ON OFF
Yes Yes
Yes Yes
Disable Disable
Enable Enable
FWD-40LX2F/40LX2X/32LX2F/32LX2X KLH-W32/W26
3
Code Table (1-a)
[a]Function 0x18 Sync Mode [b]Range/Switch Code 0x00 0x01 0x1B Clock Display 0x00 0x01 0x24 Input Detect (Option1) 0x00 0x01 0x02 0x03 0x04 0x05 0x06 0x07 0x08 0x09 H/Comp Video OFF ON FW12 (HD15) FW10 (VIDEO, S-VIDEO) BNC FW11 (BNC) Reserved FW31/32 FW50 (RGB) FW20 (UART + CTRL-S) Reserved Reserved Reserved No Yes Disable Enable Yes Yes Disable Enable Command Control Yes Enquiry Yes Standby Disable Power On Enable
0x0A Reserved 0x0B Reserved 0x0C Reserved 0x0D Reserved 0x0E Reserved 0x0F Not Connect 0x25 Input Detect (Option2)
*2
0x00 0x01 0x02 0x03 0x04 0x05 0x06 0x07 0x08 0x09
FW12 (HD15) FW10 (VIDEO, S-VIDEO) BNC FW11 (BNC) Reserved Reserved Reserved FW20 (UART + CTRL-S) Reserved Reserved Reserved
No
Yes
Disable
Enable
0x0A Reserved 0x0B Reserved 0x0C Reserved 0x0D Reserved 0x0E Reserved 0x0F Not Connect 0x30 PAP*2 0x00 0x01 0x31 Active Picture
*2
OFF P&P Left Right Swap
Yes
Yes
Disable
Enable
0x00 0x01 0x02
Yes
No
Disable
Enable
4
FWD-40LX2F/40LX2X/32LX2F/32LX2X KLH-W32/W26
Code Table (1-a)
[a]Function 0x32 Picture Size (P&P)
*2
[b]Range/Switch Code 0x00 0x01 0x02 Large Left Even Large Right INPUT1 RGB (Analog) INPUT1 YUV (Analog) OPTION1 VIDEO OPTION1 S-VIDEO OPTION1 RGB OPTION1 COMPONENT OPTION2 VIDEO OPTION2 S-VIDEO OPTION2 RGB OPTION2 COMPONENT INPUT2 RGB (Digital) INPUT2 DTV (Digital) INPUT3 RGB (Digital) INPUT3 DTV (Digital) INPUT1 RGB (Analog) INPUT1 YUV (Analog) OPTION1 VIDEO OPTION1 S-VIDEO OPTION1 RGB OPTION1 COMPONENT OPTION2 VIDEO OPTION2 S-VIDEO OPTION2 RGB OPTION2 COMPONENT INPUT2 RGB (Digital) INPUT2 DTV (Digital) INPUT3 RGB (Digital) INPUT3 DTV (Digital) Main + Remocon Main Remocon All Off Limited*4 Every Day (Repeat) Day Of Week
Command Control Yes
Enquiry Yes
Standby Disable
Power On Enable
0x35
PAP Input Detect (Left)
*2
0x08 0x09 0x0C 0x0D 0x0E 0x0F 0x10 0x11 0x12 0x13 0x44 0x45 0x54 0x55
No
Yes
Disable
Enable
0x36
PAP Input Detect (Right)
*2
0x08 0x09 0x0C 0x0D 0x0E 0x0F 0x10 0x11 0x12 0x13 0x44 0x45 0x54 0x55
No
Yes
Disable
Enable
0x45
Control Mode
0x00 0x01 0x02 0x03 0x04
Yes
Yes
Disable
Enable
0x46
On Off Timer Mode*2
0x00 0x01
Yes
Yes
Enable
Enable
FWD-40LX2F/40LX2X/32LX2F/32LX2X KLH-W32/W26
5
Code Table (1-a)
[a]Function 0x47 On Timer Enable
*2
[b]Range/Switch Code bit0 bit1 bit2 bit3 bit4 bit5 bit6 bit7 Sunday 1:Enable, 0:Disable Monday 1:Enable, 0:Disable Tuesday 1:Enable, 0:Disable Wednesday 1:Enable, 0:Disable Thursday 1:Enable, 0:Disable Friday 1:Enable, 0:Disable Saturday 1:Enable, 0:Disable Every day 1:Enable, 0:Disable Sunday 1:Enable, 0:Disable Monday 1:Enable, 0:Disable Tuesday 1:Enable, 0:Disable
Command Control Yes
Enquiry Yes
Standby Enable
Power On Enable
0x48
Off Timer Enable*2
bit0 bit1 bit2 bit3 bit4 bit5 bit6 bit7
Yes
Yes
Enable
Enable
Wednesday 1:Enable, 0:Disable Thursday 1:Enable, 0:Disable Friday 1:Enable, 0:Disable Saturday 1:Enable, 0:Disable Every day 1:Enable, 0:Disable Yes Yes Enable Enable
0x65
IP Setting Mode
0x00 DHCP 0x01 Manual 0x02 Speed
0x66
IP Setting Execute
0x00 No 0x01 Yes
No
Yes
Enable
Enable
0x67
IP Setting Result
0x00 Done 0x01 Error 1 (UART Commu.) 0x02 Error 2 (Duplication) 0x03 Error 3 (IP Add Setting) 0x04 Error 4 (GW Add setting) 0x05 Error 5 (DNS1 Setting) 0x06 Error 6 (DNS2 Setting) 0x07 Error 7 (Sbnt Msk Setting)
Yes
No
Enable
Enable
0x68
Speed Setting
0x00 100 Mbps/Full Duplex 0x01 100 Mbps/Half Duplex 0x02 10 Mbps/Full Duplex 0x03 10 Mbps/Half Duplex 0x04 Auto
Yes
Yes
Enable
Enable
0x70
Input Skip
bit0 bit1 bit2 bit3 bit4 bit5 bit6 bit7
HD15 HDMI1 HDMI2 Reserved Reserved Reserved Reserved Reserved
Yes
Yes
Disable
Enable
6
FWD-40LX2F/40LX2X/32LX2F/32LX2X KLH-W32/W26
Code Table (1-a)
[a]Function 0x71 Default Input [b]Range/Switch Code 0x00 0x01 0x73 Auto Signal Detect 0x00 0x01 0x74 HDMI Signal Detect
*5
Command Control Yes
Enquiry Yes
Standby Enable
Power On Enable
Last Memory Option1 Off On VIDEO PC Stable Unstable/No Signal NTSC PAL/SECAM
Yes
Yes
Enable
Enable
0x00 0x01
No
Yes
Disable
Enable
0x75
Signal Status *6
0x00 0x01
No
Yes
Disable
Enable
0x76
VIDEO Signal Detect
0x00 0x01
No
Yes
Disable
Enable
*1: Transmit the next command 3 seconds Power On and Power Off commands are transmitted. If not,correct data may not be able to be acquired. *2: KLH-W26/W32 does not have this function. *3: This unit automatically detects the input signal. Therefore changing in automatically if not setting a kind of signal. (RGB and Component, PC and VIDEO in HDMI etc) *4: Restricts the following key operations. [Remote Commander] Menu, Picture, Sound, ECO (Power Saving), Sleep, Contrast+/_, Brightness, Chroma, H Shift, V Shift, V size, PAP [Main] Menu *5: HDMI Signal Detect is Enable only when the signal is in Stable. *6: In the case of two windows, returns Signal Status of Active Window.
FWD-40LX2F/40LX2X/32LX2F/32LX2X KLH-W32/W26
7
(b) Time Control Clock Set (Hour, Minute)
Syntax Header Category Control 0x8C 0x00 Function 0x22 Data1 0x03 Data2 Hour: 0x00-0x17 Data3 Minute: 0x00-0x3B Check Sum 0xXX
Syntax Enquiry
Header 0x83
Category 0x00
Function 0x22
Data1 0xFF
Data2 0xFF
Check Sum 0xA3
Answer Control
Header 0x70 0x70 0x70 0x70
Answer 0x00 0x01 0x02 0x03
Check Sum 0x70 0x71 0x72 0x73 Completed Limit Over Limit Under Command Canceled
Answer Header Enquiry 0x70
Answer Return to Data Size 0x00 0x03
Return Data1 Hour: 0x00-0x17
Return Data2 Minute: 0x00-0x3B
Check Sum 0xXX Completed
Clock Set (Week)
Syntax Control Header 0x8C Category 0x00 Function 0x23 Data1 0x02 Data2 Week: Code Table (1-e) Check Sum 0xXX
Syntax Enquiry
Header 0x83
Category 0x00
Function 0x23
Data1 0xFF
Data2 0xFF
Check Sum 0xA4
Answer Control
Header 0x70 0x70 0x70 0x70
Answer 0x00 0x01 0x02 0x03
Check Sum 0x70 0x71 0x72 0x73 Completed Limit Over Limit Under Command Canceled
Answer Enquiry
Header 0x70
Answer 0x00
Return to Data Size 0x02
Return Data1 Week:Code Table (1-e)
Check Sum 0xXX Completed
8
FWD-40LX2F/40LX2X/32LX2F/32LX2X KLH-W32/W26
Code Table (1-e)
Week Select 0x00 0x01 0x02 0x03 0x04 0x05 0x06 Sunday Monday Tuesday Wednesday Thursday Friday Saturday
On Timer, Off Timer*1
Syntax Control Header 0x8C Category 0x00 Function Code Table (1-f)[a] Data1 0x03 Data2 Hour: 0x00-0x17 Data3 Minute: 0x00-0x3B Check Sum 0xXX
Syntax Enquiry
Header 0x83
Category 0x00
Function Code Table (1-f)[a]
Data1 0xFF
Data2 0xFF
Check Sum 0xXX
Answer Control
Header 0x70 0x70 0x70 0x70
Answer 0x00 0x01 0x02 0x03
Check Sum 0x70 0x71 0x72 0x73 Completed Limit Over Limit Under Command Canceled
Answer Enquiry
Header 0x70
Answer 0x00
Return to Data Size 0x03
Return Data1 Hour: 0x00-0x17
Return Data2 Minute: 0x00-0x3B
Check Sum 0xXX Completed
FWD-40LX2F/40LX2X/32LX2F/32LX2X KLH-W32/W26
9
Code Table(1-f)
[a]Function Clock Set 0x22 0x23 On Timer 0x50 0x51 0x52 0x53 0x54 0x55 0x56 0x57 Off Timer 0x58 0x59 0x5A 0x5B 0x5C 0x5D 0x5E 0x5F Sunday Monday Tuesday Wednesday Thursday Friday Saturday Every day Yes Yes Disable Enable Sunday Monday Tuesday Wednesday Thursday Friday Saturday Every day Yes Yes Disable Enable Hour, Minute Week Yes Yes Disable Enable [b]Range/Switch code Command Control Enquiry Standby Power On
*1: KLH-W26/W32 does not have this function.
(c) IP Address Setting IP Address
Syntax Control Header 0x8C Category 0x00 Function 0x42 Data1 0x05 Data2 Address 0 0x00-0xFF Data3 Address 1 0x00-0xFF Data4 Address 2 0x00-0xFF Data5 Address 3 0x00-0xFF Check Sum 0xXX
Subnet Mask
Syntax Control Header 0x8C Category 0x00 Function 0x61 Data1 0x05 Data2 Address 0 0x00-0xFF Data3 Address 1 0x00-0xFF Data4 Address 2 0x00-0xFF Data5 Address 3 0x00-0xFF Check Sum 0xXX
Gateway Address
Syntax Control Header 0x8C Category 0x00 Function 0x62 Data1 0x05 Data2 Address 0 0x00-0xFF Data3 Address 1 0x00-0xFF Data4 Address 2 0x00-0xFF Data5 Address 3 0x00-0xFF Check Sum 0xXX
10
FWD-40LX2F/40LX2X/32LX2F/32LX2X KLH-W32/W26
DNS Primary
Syntax Control Header 0x8C Category 0x00 Function 0x63 Data1 0x05 Data2 Address 0 0x00-0xFF Data3 Address 1 0x00-0xFF Data4 Address 2 0x00-0xFF Data5 Address 3 0x00-0xFF Check Sum 0xXX
DNS Secondary
Syntax Control Header 0x8C Category 0x00 Function 0x64 Data1 0x05 Data2 Address 0 0x00-0xFF Data3 Address 1 0x00-0xFF Data4 Address 2 0x00-0xFF Data5 Address 3 0x00-0xFF Check Sum 0xXX
Answer Control
Header 0x70 0x70
Answer 0x00 0x03
Check Sum 0x70 0x73 Completed Command Canceled
192(0xC0)...Address 0 128(0x80)...Address 1 14(0x0E)...Address 2 1(0x01)...Address 3 * IP address command can be carried out even in the standby state.
IP Address ex) 192.128.14.1
Code Table(1-a)
[a]Function 0x42 0x61 0x62 0x63 0x64 IP Address Subnet Mask Gateway Address DNS Primary DNS Secondary [b]Range/Switch code Command Control Yes Enquiry Yes Standby Enable Power On Enable
5. Picture/Sound
(a) Picture/Sound
Syntax Control Enquiry Header 0x8C 0x83 Category 0x10 Function Code Table (2-a)[a] Data1 0x02 0xFF Data2 Code Table (2-a)[b] 0xFF Check Sum 0xXX 0xXX
Answer Control
Header 0x70 0x70 0x70 0x70
Answer 0x00 0x01 0x02 0x03
Check Sum 0x70 0x71 0x72 0x73 Completed Limit Over Limit Under Command Canceled
Answer Enquiry
Header 0x70
Answer 0x00
Return to Data Size 0x02
Return Data1 Code Table (2-a)[b]
Check Sum 0xXX Completed
FWD-40LX2F/40LX2X/32LX2F/32LX2X KLH-W32/W26
11
Code Table (2-a)
[a]Function 0x00 0x01 0x02 0x03 0x04 Contrast Brightness Chroma Phase Color Temp [b]Range/Switch code 0x00-0x64 0x00-0x64 0x00-0x64 0x00-0x64 0x00 0x01 0x02 0x10 Picture Mode 0x00 0x01 0x02 0x05 0x30 0x31 0x32 0x33 0x35 Volume Treble*1 Bass*1 Balance Sound Mode 0x00-0x64 0x00-0x0C 0x00-0x0C 0x00-0x1E 0x00 0x01 0x02 0x03 0x36 0x37 Default Volume Set 0x00-0x64 Volume Select 0x00 0x01 0x38 Max Volume Set 0x00 0x01 0x02 0x39 Common Audio Select 0x00 0x01 0x02
*1: *2:
Command Control Yes Yes Yes Yes
Enquiry Yes Yes Yes Yes Yes
Standby Disable Disable Disable Disable Disable
Power On Enable Enable Enable Enable Enable
Cool Neutral Warm Standard Vivid Custom TC Control
Yes
Yes
Yes
Disable
Enable
Yes Yes Yes Yes Dynamic Standard SRS Custom Yes Last Memory Default Setting 100 70 50 HD15 HDMI1 HDMI2 Yes Yes Yes Yes
Yes Yes Yes Yes Yes
Enable Disable Disable Disable Disable
Enable Enable Enable Enable Enable
Yes Yes
Enable Enable
Enable Enable
Yes
Enable
Enable
Yes
Disable
Enable
Sound mode = Custom and Speaker = On is enable KLH-W26/W32 does not have this function.
(b) Color Temp
Syntax Control Header 0x8C Category 0x10 Function Code Table (2-b)[a] Data1 0x03 Data2 Code Table (2-c) Data3 Code Table (2-b)[b] Check Sum 0xXX
Syntax Enquiry
Header 0x83
Category 0x10
Function Code Table (2-b)[a]
Data1 Code Table (2-c)
Data2 0xFF
Check Sum 0xXX
12
FWD-40LX2F/40LX2X/32LX2F/32LX2X KLH-W32/W26
Answer Control
Header 0x70 0x70
Answer 0x00 0x03
Check Sum 0x70 0x73 Completed Command Canceled
Answer Enquiry
Header 0x70
Answer 0x00
Return to Data Size 0x03
Return Data1 Code Table (2-c)
Return Data2 Code Table (2-b)[b]
Check Sum 0xXX Completed
Code Table (2-b)
[a]Function 0x05 0x06 0x07 Red Gain Green Gain Blue Gain [b]Range/Switch code 0x00-0xFF 0x00-0xFF 0x00-0xFF Command Control Yes Enquiry Yes Standby Disable Power On Enable
Code Table (2-c)
Format Select 0x00 0x01 0x02 Cool Neutral Warm
6. Size/Shift
(a) 8Bits Register
Syntax Control Enquiry Header 0x8C 0x83 Category 0x20 Function Code Table (3-b)[a] Data1 0x02 0xFF Data2 Code Table (3-b)[b] 0xFF Check Sum 0xXX 0xXX
Answer Control
Header 0x70 0x70 0x70 0x70
Answer 0x00 0x01 0x02 0x03
Check Sum 0x70 0x71 0x72 0x73 Completed Limit Over Limit Under Command Canceled
Answer Enquiry
Header 0x70
Answer 0x00
Return to Data Size 0x02
Return Data1 Code Table (3-b)[b]
Check Sum 0xXX Completed
FWD-40LX2F/40LX2X/32LX2F/32LX2X KLH-W32/W26
13
Code Table (3-b)
[a]Function 0x01 0x02 0x03 0x04 H Shift V Size
*2
[b]Range/Switch code (PC) 0x00-0x3C, (Video) 0x00-0x0A (Video) 0x00-0x0A (PC) 0x00-0x28, (Video) 0x00-0x0A 0x00 0x01 0x02 0x04 0x05 0x06 Wide Zoom (VIDEO Only) Zoom (VIDEO Only) Full (VIDEO Only) Normal (PC, VIDEO) Full 1 (PC Only) Full 2 (PC Only) OFF x2 x3 x4 Execute Position1 Position2 Position3 Position4 Position1 Position2 Position3 Position4 Position5 Position6 Position7 Position8 Position9
Command Control Yes Yes Yes Yes
Enquiry Yes Yes Yes Yes
Standby Disable Disable Disable Disable
Power On Enable Enable Enable Enable
V Shift Aspect
0x05
Multi Display
*3
0x00 0x01 0x02 0x03
Yes
Yes
Disable
Enable
0x06 0x0B
Auto Pixel Adjust Multi Position (x2)
*1*3
0xFF 0x00 0x01 0x02 0x03
Yes Yes
No Yes
Disable Disable
Enable Enable
0x0C
Multi Position (x3)
*1*3
0x00 0x01 0x02 0x03 0x04 0x05 0x06 0x07 0x08
Yes
Yes
Disable
Enable
14
FWD-40LX2F/40LX2X/32LX2F/32LX2X KLH-W32/W26
[a]Function 0x0D Multi Position (x4)*1*3
[b]Range/Switch code 0x00 0x01 0x02 0x03 0x04 0x05 0x06 0x07 0x08 0x09 0x0A 0x0B 0x0C 0x0D 0x0E 0x0F Position1 Position2 Position3 Position4 Position5 Position6 Position7 Position8 Position9 Position10 Position11 Position12 Position13 Position14 Position15 Position16 Tiles Window Normal _1 _2
Command Control Yes
Enquiry Yes
Standby Disable
Power On Enable
0x0F
Multi Display Output Format
*3
0x00 0x01 0x00 0x01 0x02
Yes
Yes
Disable
Enable
0x10
Display Area*3
Yes
Yes
Disable
Enable
*1: Arrangement of Multi Position.
Multi Position (x2)
1 3 2 4
Multi Position (x3)
1 4 7 2 5 8 3 6 9
Multi Position (x4)
1 5 9 13 2 6 10 14 3 7 11 15 4 8 12 16
*2: VIDEO Mode Only is Enabled. *3: KLH-W26/W32 does not have this function.
FWD-40LX2F/40LX2X/32LX2F/32LX2X KLH-W32/W26
15
7. Status Enquiry
(a) Model Name
Syntax Enquiry Header 0x83 Category 0x30 Function 0x00 Data1 0xFF Data2 0xFF Check Sum 0xB1
Answer Enquiry
Header 0x70
Answer 0x00
Return to Data Size 0x02
Return Data1 Code Table (4-a)
Check Sum 0xXX Completed
Code Table(4-a)
Format Select 0x0C 0x0D 0x0E 0x0F 0x60 0x61 FWD-40LX2X FWD-32LX2X FWD-40LX2F FWD-32LX2F KLH-W26 KLH-W32
(b) Serial Number
Syntax Enquiry Header 0x83 Category 0x30 Function 0x01 Data1 0xFF Data2 0xFF Check Sum 0xB2
Answer Header Enquiry 0x70
Answer 0x00
Return to Data Size 0x05
Return Data1 Upper 8bit Data
Return Data2 Middle Upper Data
Return Data3 Return Data4 Check Sum Middle Lower Data Lower 8bit Data 0xXX Completed
Return Data1-Data4: 0x00000000-0x0098967F (0,000,000-9,999,999)
(c) Operation Time
Syntax Enquiry Header 0x83 Category 0x30 Function 0x02 Data1 0xFF Data2 0xFF Check Sum 0xB3
Answer Header Enquiry 0x70
Answer 0x00
Return to Data Size 0x05
Return Data1 Upper 8bit Data
Return Data2 Middle Upper Data
Return Data3 Return Data4 Check Sum Middle Lower Data Lower 8bit Data 0xXX Completed
Return Data1-Data4: 0x00000000-0x15751BF0 (0sec._359,996,400 sec.)
16
FWD-40LX2F/40LX2X/32LX2F/32LX2X KLH-W32/W26
(d) Soft Version (Main CPU)
Syntax Enquiry Header 0x83 Category 0x30 Function 0x03 Data1 0xFF Data2 0xFF Check Sum 0xB4
Answer Enquiry
Header 0x70
Answer 0x00
Return to Data Size 0x03
Return Data1 Upper 8bit Data
Return Data2 Lower 8bit Data
Check Sum 0xXX Completed
Return Data1-Data2: 0x0000-0x9999 (BCD Format) ex) In Version0.100, it is set to 01 and 00.
(e) 8bits Register
Syntax Enquiry Header 0x83 Category 0x30 Function Code Table (4-b) Data1 0xFF Data2 0xFF Check Sum 0xXX
Answer Enquiry
Header 0x70
Answer 0x00
Return to Data Size 0x02
Return Data1 Code Table (4-b)
Check Sum 0xXX Completed
Code Table(4-b)
Function 0x0A 0x0D 0x10 0x16 Temp1 Temp (P/S) Analog 5 V Analog 13 V Return Data 0x00-0xFF 0x00-0xFF 0x00-0xFF 0x00-0xFF Unit
(f) Shutdown Log
Syntax Enquiry Header 0x83 Category 0x30 Function 0x11 Data1 0xFF Data2 0xFF Check Sum 0xC2
Answer Enquiry
Header 0x70
Answer 0x00
Return to Data Size 0x02
Return Data1 Shutdown Log Code
Check Sum 0xXX Completed
Return Data1: 0x00-0xFF
Code Table (4-c)
Shutdown bit0 bit1 bit2 bit3 bit4 bit5 bit6 bit7 Information Reserved Reserved 1: Panel communication Abnormal, 0: Normal 1: Temperature Sensor Abnormal, 0: Normal Reserved Reserved 1: Analog Power Abnormal (13 V, 5 V) 0: Normal Reserved
FWD-40LX2F/40LX2X/32LX2F/32LX2X KLH-W32/W26
17
(g) Auto Input Detect
Syntax Enquiry Header 0x83 Category 0x30 Function 0x30 Data1 0xFF Data2 0xFF Check Sum 0xE1
Answer Header Enquiry 0x70
Answer 0x00
Return to Data Size 0x0C
Return Data1 Input1 Input Type Code Table (4-e)
Return Data2 Input2 Input Type Code Table (4-e)
Return Data3 Input3 Input Type Code Table (4-e)
Return Data4 Input4 Input Type Code Table (4-e)
Return Data5 Input5 Input Type Code Table (4-e)
Return Data6 Option1 Option Type Code Table (4-e)
Return Data7 Option1 Input Type Code Table (4-e)
Return Data8 Option2 Option Type Code Table (4-e)
Return Data9 Option2 Input Type Code Table (4-e)
Return Data10 Option3 Option Type Code Table (4-e)
Return Data11 Option3 Input Type Code Table (4-e)
Check Sum 0xXX Completed
FWD-40LX2F/40LX2X/32LX2F/32LX2X
Input INPUT1 INPUT2 INPUT3 INPUT4 INPUT5 OPTION1 Input Type (Basic) 0x06 0x08 0x08 0x00 0x00 RGB/YUV (Analog) HDMI HDMI No Input No Input 0x00 0x00 0x00 0x00 0x03 OPTION2 0x00 0x00 0x00 0x00 0x03 OPTION3 0x00 Analog Only Analog Only Analog Only Analog Only Com Only Analog Only Analog Only Analog Only Analog Only Com Only Analog Only 0x00 0x03 0x06 0x07 0x00 0x00 0x03 0x06 0x07 0x00 0x00 No Input Video/S-Video RGB/YUV (Analog) Video/S-Video/RGB/YUV (Analog) No Input No Input Video/S-Video RGB/YUV (Analog) Video/S-Video/RGB/YUV (Analog) No Input No Input Option Type Input Type (Option)
18
FWD-40LX2F/40LX2X/32LX2F/32LX2X KLH-W32/W26
KLH-W26/W32
Input INPUT1 INPUT2 INPUT3 INPUT4 INPUT5 OPTION1 Input Type (Basic) 0x06 0x08 0x08 0x00 0x00 RGB/YUV (Analog) HDMI HDMI No Input No Input 0x00 0x00 0x00 0x00 0x03 OPTION2 OPTION3 0x00 0x00 Analog Only Analog Only Analog Only Analog Only Com Only Analog Only Analog Only 0x00 0x03 0x06 0x07 0x00 0x00 0x00 No Input Video/S-Video RGB/YUV (Analog) Video/S-Video/RGB/YUV (Analog) No Input No Input No Input Option Type Input Type (Option)
(h) Auto Panel Type Detect
Syntax Enquiry Header 0x83 Category 0x30 Function 0x31 Data1 0xFF Data2 0xFF Check Sum 0xE2
Answer Enquiry
Header 0x70
Answer 0x00
Return to Data Size 0x02
Return Data1 Code Table (4-h)
Check Sum 0x72 Completed
Code Table (4-h)
Panel Type 0x00 LCD
Code Table (4-d)
[a]Function 0x00 0x01 0x02 0x03 0x0A 0x0D 0x10 0x11 0x16 0x30 0x31 Model Name Serial Number Operation Time Soft Version (Main) Temp1 Temp(P/S) Analog5V Shutdown Log Analog13V Auto Input Detect Auto Panel Type Detect [b]Range/Switch code 0x0C-0x11, 0x40-0x41, 0x60 0x00000000-0x0098967F 0x00000000-0x15751BF0 0x0000-0x9999 0x00-0xFF 0x00-0xFF 0x00-0xFF 0x00-0xFF 0x00-0xFF Command Control No Enquiry Yes Standby Enable Power On Enable
FWD-40LX2F/40LX2X/32LX2F/32LX2X KLH-W32/W26
19
8. User Reset
Syntax Control Header 0x8C Category 0x50 Function Code Table (5) Data1 0x02 Data2 0xFF Check Sum 0xXX
Answer Control
Header 0x70 0x70
Answer 0x00 0x03
Check Sum 0x70 0x73 Completed Command Canceled
Code Table (5)
Function 0x00 0x01 0x02 0x03 0x04 Picture Reset Audio Reset Size Reset Picture Reset2 (FW50) All Reset Size, Shift, Dot Clock, Phase Contrast, Brightness, Chroma, Phase Range/Switch code Command Control Yes Enquiry No Standby Disable Power On Enable
9. Service
(a) Mode
Syntax Control Header 0x8C Category 0xF0 Function Code Table (6) Data1 0x02 Data2 0xFF Check Sum 0xXX
Syntax Enquiry
Header 0x83
Category 0xF0
Function 0x00
Data1 0xFF
Data2 0xFF
Check Sum 0x71
Answer Control
Header 0x70 0x70
Answer 0x00 0x03
Check Sum 0x70 0x73 Completed Command Canceled
Answer Enquiry
Header 0x70
Answer 0x00
Return to Data Size 0x02
Return Data1 Code Table (7)
Check Sum 0xXX Completed
20
FWD-40LX2F/40LX2X/32LX2F/32LX2X KLH-W32/W26
Code Table (6)
Function 0x00 0x01 Service Mode IN Service Mode Exit Range/Switch code Command Control Yes Enquiry Yes Normal Mode Disable Service Mode Enable
Code Table (7)
Function 0x00 0x01 User Mode Service Mode Range/Switch code Command Control Yes Enquiry Yes Normal Mode Disable Service Mode Enable
(b) Factory Reset
Syntax Control Header 0x8C Category 0x40 Function Code Table (8) Data1 0x02 Data2 0xFF Check Sum 0xXX
Answer Control
Header 0x70
Answer 0x00
Check Sum 0x70 Completed
Code Table (8)
Function 0x88 Factory Reset Range/Switch code Command Control Yes Enquiry No Normal Mode Disable Service Mode Enable
FWD-40LX2F/40LX2X/32LX2F/32LX2X KLH-W32/W26
21
The material contained in this manual consists of information that is the property of Sony Corporation. Sony Corporation expressly prohibits the duplication of any portion of this manual or the use thereof for any purpose other than the operation or maintenance of the equipment described in this manual without the express written permission of Sony Corporation.
Le matériel contenu dans ce manuel consiste en informations qui sont la propriété de Sony Corporation. Sony Corporation interdit formellement la copie de quelque partie que ce soit de ce manuel ou son emploi pour tout autre but que des opérations ou entretiens de l'équipement à moins d'une permission écrite de Sony Corporation.
Das in dieser Anleitung enthaltene Material besteht aus Informationen, die Eigentum der Sony Corporation sind. Die Sony Corporation untersagt ausdrücklich die Vervielfältigung jeglicher Teile dieser Anleitung oder den Gebrauch derselben für irgendeinen anderen Zweck als die Bedienung oder Wartung der in dieser Anleitung beschriebenen Ausrüstung ohne ausdrückliche schriftliche Erlaubnis der Sony Corporation.
FWD-40LX2F/40LX2X/32LX2F/32LX2X KLH-W32/W26
FWD-40LX2F (WW) FWD-40LX2X (WW) FWD-32LX2F (WW) FWD-32LX2X (WW) KLH-W32 (WW) KLH-W26 (WW) E 9-834-146-01 Printed in Japan 2006. 12 22 ©2006
Sony Corporation