Text preview for : MX-M260 MX-M310 MX-M260N MX-M310N INSTALLATION MANUAL.pdf part of Sharp Andromeda II refresh Polish and English language
Back to : Andromeda ll refresh.part | Home
INSTALLATION MANUAL
CODE: 00ZMXM310/I1E
DIGITAL MULTIFUNCTIONAL SYSTEM
MODEL
MX-M260/M310 MX-M260N/M310N
CONTENTS
[1] MX-M260/M260N/M310/M310N (Main unit) . . . . . . . . . . . . . . . . . . 1-1 [2] MX-RP10 (Reversing single pass feeder) . . . . . . . . . . . . . . . . . . . . 2-1 [3] MX-DE10/DE11 (Paper feed unit) . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1 [4] MX-DS11/DS12 (Machine stand) . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1 [5] MX-FN13 (Finisher). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1 [6] MX-TE10 (Paper exit tray) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1 [7] MX-TR11 (Job separator tray). . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1 [8] MX-PB12 (Printer expansion kit). . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1 [9] AR-SM5/SM6 (256MB Expansion memory board/ 512MB Expansion memory board) . . . . . . . . . . . . . . . . . . . . . . . . . 9-1 [10] MX-PK10 (PS3 Expansion kit) . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-1 [11] AR-PF1/PF2 (Barcode font kit/Macro font flash ROM kit) . . . . . . . 11-1 [12] MX-NSX1 (Network scanner expansion kit) . . . . . . . . . . . . . . . . . 12-1 [13] AR-FX7 (Facsimile expansion kit) . . . . . . . . . . . . . . . . . . . . . . . . . 13-1 [14] MX-FR17U/FR18U (Data security kit). . . . . . . . . . . . . . . . . . . . . . 14-1 [15] MX-AMX1 (Application integration module) . . . . . . . . . . . . . . . . . 15-1
Parts marked with " " are important for maintaining the safety of the set. Be sure to replace these parts with specified ones for maintaining the safety and performance of the set.
This document has been published to be used for after sales service only. The contents are subject to change without notice.
[1] MX-M260/M260N/M310/M310N (Main unit)
1. Installation
A. Environment
The performance of this machine is affected by the environment of the installing site. Avoid installation to the following places: · Avoid installation in direct sunlight, otherwise the plastic parts may be deformed. · Avoid installation to a place where there is ammonium gas. Installation near a diazo-copier may lead to dirty copy.
· Be sure to have enough space around the machine. Be sure to allow the required space around the machine for servicing and proper ventilation.
12" (30cm)
· Avoid installation in a place of high temperature, high humidity, low temperature or low humidity, otherwise paper may be dampened and frost may be generated in the machine to cause a paper jam and dirty copy.
12" (30cm)
12" (30cm)
B. Power source
· Check that the following power capacity is satisfied. If not, additionally provide a power source. Current capacity 100V : 12A or more 120V±10% : 15A 200V : 8A or more · Install the machine near the power outlet to facilitate connection of the power plug. · If the power plug of this machine and other illuminating apparatus are connected to the same power outlet, the lamp may flicker. Use an exclusive power outlet for this machine without connecting another lamp together. · Avoid installation to a place with much vibration, otherwise the machine may cause troubles. · Avoid complex wiring. Be careful not to damage, break, or process the power cord.
· Avoid installation in a dusty place, otherwise dust may enter the machine to cause dirty copy or machine troubles.
· Avoid installation to a place of poor ventilation.
· Earth wire connection Be sure to connect the earth wire for protection against danger. If not, improper grounding may cause a fire or an electric shock.
Earth terminal
MX-M260/M310/M260N/M310N MX-M260/M260N/M310/M310N (Main unit) 1 - 1
C. Transport
· When transporting the machine, use two people to lift the machine using the two grips provided on each side of the machine.
· When disconnecting the power plug from the power outlet, do not pull the cord.
· Do not throw toner or the toner cartridge into a fire. · Keep toner or the toner cartridge away from the children. · When the exclusive table (option) is used, be sure to use the adjusters (4 pcs.) on the floor. When it is required to move the machine for rearrangement of the office, etc., release the adjuster locks and move the machine.
D. Other precautions
· If the machine produces smoke or bad smell, stop the operation of the machine.
Adjuster Lock Release
· Do not use flammable spray near the machine. · Do not remove the cabinet of the machine. · Do not put a receptacle with water in it or metal pieces, which may drop inside the machine, causing a trouble.
· The fusing section is heated to a high temperature. When removing a paper jam, be careful not to touch the fusing section.
Fusing section
· When the machine is not used for a long time, disconnect the power plug from the power outlet for safety. · When it thunders, turn off the power and disconnect the power plug from the power outlet to prevent against an electric shock or a fire caused by lighting damage. · If a piece of metal or water enters the machine, turn off the power and disconnect the power plug from the power outlet. · Do not touch the power plug with a wet hand. · When transporting the machine, turn off the power and disconnect the power plug from the power outlet. (Remove the earth wire after disconnecting the power plug from the power outlet.)
2. Removal of protective material and fixing screw
1) Remove all tapes, then open the document cover and remove the protective material of sheet shape. 2) Use a screwdriver to remove the fixing screw. The fixing screw is required when transporting the machine. Keep it in the tray. (Refer to the later description.)
· Do not remodel the machine. · Be careful not to pinch your fingers when closing the front cover or the side cover and setting the paper feed tray to supply paper or process a paper jam.
MX-M260/M310/M260N/M310N MX-M260/M260N/M310/M310N (Main unit) 1 - 2
3. Removal and storage of fixing pin
1) Lift the knob and gently pull out the tray.
3) Remove the cover from the developer unit.
4) Rotate the MG roller in the arrow direction and supply developer evenly into the developing unit. 2) Hold the paper pressure plate and turn the fixing pin in the arrow direction.
3) Store the removed fixing pin and the fixing screw which was removed in the above procedure, together in the specified storage place in the tray.
MG roller
Shake the developer bag well before opening it. Check that the DV seal is free from developer. If developer is attached to the DV seal, clean and remove it. 5) After supplying developer into the developer unit, do not tilt or shake the developer unit.
Fixing pin
6) Attach the developer unit to the copier, and fix it with the screw.
5. Toner cartridge installation
1) Shake it about 4 - 5 times horizontally.
Fixing screw
If power is turned don without removing the fixing pin, it will be difficult to pull out the tray.
4. Developer supply
1) Hold the both sides of the front cover, and pull down to open it.
2) Press the lock release lever, and insert the unit completely into the copier along the guide groove.
2) Loosen the blue screw and pull out the developing unit. Dirt or dust must be removed from the toner cartridge before installing.
MX-M260/M310/M260N/M310N MX-M260/M260N/M310/M310N (Main unit) 1 - 3
6. Toner density sensor level adjustment
1) Open the cover with the power OFF. 2) Power ON (The mechanism cannot be initialized because the cover is open.) 3) Install the developing unit with new developer in it. 4) Enter SIM 25-2. (# C 25 START 2 START) 5) Close the cover immediately before starting the operation. 6) Press the [START] key to start. After completion of the adjustment, be sure to cancel the simulation with the [CA] key.
5) Select the size and type of paper that is loaded in the tray. The currently selected paper type will be highlighted. · To change the paper type selection, touch the appropriate type key. · To change the paper size selection, touch the appropriate size key. · To change the displayed size selections to AB sizes, touch [AB INCH].
SYSTEM SETTINGS TRAY 1 TYPE/SIZE SETTING TYPE PLAIN LETTER HEAD COLOR 11x17 8½x11 SIZE 8½x14 8½x11R AB OK INCH 8½x13 5½x8½
7. Tray paper size setting
When you change the paper in a tray, follow the steps below to change the tray's paper type and paper size settings. The settings cannot be changed when operation has stopped because the paper ran out or a misfeed occurred, or when an interrupt copy job is being performed. Even in copy mode, the settings cannot be changed while a print job or received fax is being printed. Note: · 5-1/2" x 8-1/2" (A5) size paper can only be set for tray 1. · B5 size paper cannot be set for tray 2 (However, B5R size paper can be set.). · Tray settings for trays other than the bypass tray can be prohibited in the key operator programs.
RECYCLED
6) Touch the [OK] key. 7) A message appears prompting you to check the paper in the tray. Check the paper and then touch the [OK] key. You will return to the tray settings screen.
B. Manual feed tray
Use either of the following two methods to set the bypass tray's paper type setting.
(1) From the [SYSTEM SETTINGS] key
1) Set paper on the tray. 2) Press the [SYSTEM SETTINGS] key. The system settings menu screen will appear.
A. Trays 1 4
1) Set paper on the tray. 2) Press the [SYSTEM SETTINGS] key. The system settings menu screen will appear.
LINE DATA B STATUS SYSTEM SETTINGS
LINE DATA B STATUS SYSTEM SETTINGS
3) Touch the [TRAY SETTINGS] key. The tray settings screen will appear.
TOT L COUNT CONTRA ADDRE CONTRO
3) Touch the [TRAY SETTINGS] key. The tray settings screen will appear.
TOT L COUNT CONTRA ADDRE CONTRO KEYBOARD SELECT KEY TRAY SETTINGS
TRAY SETTINGS
KEYBOARD SELECT
KEY
4) Touch the [BYPASS TRAY] key.
TYPE / SIZE
4) Select the tray in which you loaded paper. If the desired tray does not appear in the display, use the [] key or [] key to scroll until it appears.
TYPE / SIZE TRAY 1 PLAIN / 8½ x 11
TRAY 4 BYPASS TRAY
PLAIN / 11x17
PLAIN
TRAY 2 TRAY 3
PLAIN / 8½ x 14 PLAIN / 11x17
MX-M260/M310/M260N/M310N MX-M260/M260N/M310/M310N (Main unit) 1 - 4
5) Select the type of paper that is loaded in the tray.
SYSTEM SETTINGS BYPASS TRAY TYPE SETTING SELECT THE PAPER TYPE. PLAIN RECYCLED HEAVY PAPER LETTER HEAD COLOR THIN PAPER ENVELOPE LABELS TRANSPARENCY JAPANESE P/C OK
6) Touch the [OK] key. You will return to the tray settings screen.
(2) From the [PAPER SELECT] key
1) Set paper on the tray. 2) Touch the [PAPER SELECT] key.
3) Touch the paper type selection key.
4) Select the paper type. "JAPANESE P/C" refers to official postcards used in Japan.
5) Touch the [PAPER SELECT] key. You will return to the main screen of copy mode.
MX-M260/M310/M260N/M310N MX-M260/M260N/M310/M310N (Main unit) 1 - 5
[2] MX-RP10 (Reversing single pass feeder)
1. Unpacking
For unpacking, refer to the figure below. 3) Remove the right and left glass holders and remove the document glass. Remove the two screws (M3 x 8) of the left glass holder and the three screws (M3 x 8) of the right glass holder.
Screws (M3 x 8) Left glass holder
Screws (M3 x 8) Document glass
Right glass holder
4) Insert the RSPF glass holder to the document glass. Then, attach the document glass to the copier, fix the left glass holder that has been removed in step 3 using two screws (M3 x 8), and fix the RSPF glass using three screws (M3 x 8).
Screws (M3 x 8) Screws (M3 x 8)
· Parts included
Document glass
Left glass holder
RSPF glass holder Intermediate tray RSPF glass cover
2. Installation
1) Turn off the main switch of the copier and then remove the power plug of the copier from the outlet. 2) Lift the platen cover and remove it from the copier. 5) Insert the hinge portion of the RSPF to the mounting portion of the copier by holding the RSPF at an angle toward the rear side.
Hinge
Hinge
MX-M260/M310/M260N/M310N MX-RP10 (Reversing single pass feeder) 2 - 1
6) Remove the filament tape located in the positions shown in the illustration.
3. Adjustments
Insert the power plug of the copier to the outlet and turn on the main switch of the copier.
Filament tape
A. Adjust the RSPF white correction pixel
· Open the RSPF and execute SIM 63-7 to adjust the RSPF auto white correction pixel.
Filament tape
1) Open the SPF unit and press the START key.
SIMULATION 63-7 SHADING POSITION ADJUSTMENT. PRESS START.
Filament tape
7) Connect the Centronics connector of the RSPF to the connector of the copier and then tighten the screws of the connector.
2) Shading position adjustment is performed. (Cannot interrupt) If the simulation is executed with the SPF unit closed, an error is resulted.
SIMULATION 63-7 SHADING POSITION ADJUSTMENT. EXECUTING...
Screw Screw
3) [ ] indicates the order number of the pixel of the white sheet for SPF exposure correction in the SPF position. When the adjustment is completed normally, "COMPLETE" is displayed, and data are written into the EEPROM.
SIMULATION 63-7 SHADING POSITION ADJUSTMENT. COMPLETE. [160]
8) Insert the intermediate tray all the way into the RSPF.
Intermediate tray
When the adjustment is completed abnormally, "ERROR" is displayed and data are not written into the EEPROM.
SIMULATION 63-7 SHADING POSITION ADJUSTMENT. ERROR. [ 0]
The SPF white correction start pixel = Displayed pixel position -34.
B. Adjust the document guide width (Sim53-6)
Caution: If this adjustment is not performed, the document size display remains special. 1) With the document guide opened to the full, set A/3 (A/4) (WLT (LT) in the inch system) paper and adjust the guide. Press the start key.
SIMULATION 53-6 SPF TRAY ADJUSTMENT. WLT PAPER SET, AND PRESS START KEY.
MX-M260/M310/M260N/M310N MX-RP10 (Reversing single pass feeder) 2 - 2
2) Set to A4R (LTR) size, adjust the guide and press the start key.
SIMULATION 53-6 SPF TRAY ADJUSTMENT. LTR PAPER SET, AND PRESS START KEY.
3) Fold the A/4 (LTR) paper in half, set to the A5R (Invoice R) size, adjust the guide and press the start key.
SIMULATION 53-6 SPF TRAY ADJUSTMENT. INVR PAPER SET, AND PRESS START KEY.
4) Adjust the guide to the minimum width and press the start key.
SIMULATION 53-6 SPF TRAY ADJUSTMENT. MIN POSITION SET, AND PRESS START KEY.
5) Make sure the indicator reads 60 before pressing the start key.
SIMULATION 53-6 SPF TRAY ADJUSTMENT. INPUT VALUE 1-99, AND PRESS START. 60
6) Make sure the indicator reads 40 before pressing the start key.
SIMULATION 53-6 SPF TRAY ADJUSTMENT. INPUT VALUE 1-99, AND PRESS START. 40
7) Make sure the document size is correctly shown in Sim2-2.
C. Check the copy magnification ratio
1) Place a scale on the original table, and make a 100% copy to make a test chart. 2) Place the test chart on the RSPF and make a 100% copy. 3) Compare the scale image and actual image. 4) If adjustment is required. Execute Sim48-1
D. Check the center displacement
1) Place the center position adjustment test chart on the RSPF. 2) Make a copy from the manual paper feed tray and check the printed copy with the test chart. 3) If adjustment is required. Execute Sim 50-12
E. Check the scan position
1) Open RSPF, place a white paper on the document glass. 2) Execute Sim 53-8 and press start key. Installation of RSPF is now complete.
MX-M260/M310/M260N/M310N MX-RP10 (Reversing single pass feeder) 2 - 3
[3] MX-DE10/DE11 (Paper feed unit)
1. Unpacking
Turn off the main switch of the copier and then remove the power plug of the copier from the outlet.
A. Remove the rear cover from the copier
1) Remove the two screws and then remove the rear cover from the copier.
MX-DE10
Screw Rear cover
MX-DE11
Screw
B. Remove the rear cover from the optional paper feed unit
1) Remove the two screws and then remove the rear cover from the optional paper feed unit.
2. Installation
PARTS INCLUDED
Screw Rear cover Screws (M4 x 12): 8 pcs. Fixing plates: 4 pcs. Paper size label Screw
C. Remove the connector cover
Cassette relay harness (contained in the optional paper feed unit)
Remove all pieces of fixing tape and fixing materials from the paper feed unit. 1) Remove the cover from the connector.
Connector cover
MX-M260/M310/M260N/M310N MX-DE10/DE11 (Paper feed unit) 3 - 1
D. Attach the copier
1) Place the copier on the optional paper feed unit and remove the second and third paper trays. Connect the copier to the paper feed unit using four fixing plates and two screws (M4 x 12) for each plate.
E. Connect the harness
1) Connect the cassette interface harness contained in the optional paper feed unit to the paper feed unit interface PWB. · For two tray type
Detailed view Front side
Fixing plate Screws (M4 x 12) Screws (M4 x 12) Fixing plate Right of rear side
Cassette relay harness
Left of rear side
Fixing plate
· For one tray type
Fixing plate Screws (M4 x 12)
Screws (M4 x 12)
Cassette relay harness
F. Attach the rear covers of the copier and the optional paper feed unit
1) Attach the rear covers of the copier and the optional paper feed unit using two screws respectively.
Rear cover
Screws
Rear cover Screws
MX-M260/M310/M260N/M310N MX-DE10/DE11 (Paper feed unit) 3 - 2
G. Remove the securing fixture for packing the paper feed unit and remove the packing material
1) Remove the securing fixture for packing that fixes the paper pressure plate of the tray by rotating it in the direction of the arrow and remove the packing material.
Securing fixture for packing Packing material
Caution: Be sure to remove the securing fixture bofore turning on the power.
H. Change the paper size in the tray
1) Hold the grip and slide the tray side plate to adjust it to the paper to be used. Then, fit the rear end plate to the specified size position.
Rear plate
Side plate
Insert the power plug of the copier to the outlet and turn on the main switch of the copier. Then, carry out the following procedure.
I. Load paper into the paper tray
1) Do not exceed the maximum height line.
J. Check for center displacement
· Set an original on the document glass and copy it using the paper tray in the copier. Then, copy an original using the attached optional paper feed unit. · If the center of the copy image from the tray in the copier is different from that of the copy image from the optional paper feed unit, carry out adjustment referring to the service manual. Installation of Paper feed unit is now complete. MX-M260/M310/M260N/M310N MX-DE10/DE11 (Paper feed unit) 3 - 3
[4] MX-DS11/DS12 (Machine stand)
1. Unpacking
Unpack the package, and check to confirm that all the parts are provided.
2. Installation
1) Attach the casters to the desk. Remove the desk from the package, and put it on the floor as shown below. Attach the four casters and fix them with caster fixing screws. (3 screws for each caster)
Machine stand
Packed parts add
Casters
Caster fixing screws (3 for each caster)
Rear side Casters
Front side MX-DS11
2) Attach the adjusters. Attach the front adjusters (2 pcs.) and the rear adjusters (2 pcs.) as shown in the figure below.
Rear adjusters( 80)
MX-DS12
Front adjuster ( 110) Rear side Front adjuster ( 110) Front side
Packed parts
Screw the adjusters into
the hole so that the adjuster tips do not extend out from the hole.
Casters: 4pcs.
Front adjusters: 2 pcs. ( 110)
Rear adjusters: 2 pcs. ( 80)
Adjuster covers: 2 pcs.
Caster fixing screws: 12 pcs.
Copier connecting fixtures: 2 pcs.
Screws (S tight): 2 pcs.
Screws (P tight): 4 pcs.
MX-M260/M310/M260N/M310N MX-DS11/DS12 (Machine stand) 4 - 1
3) Attach the adjuster covers. Put the desk on the floor in the normal state, and open the door. (MX-DS11 only) Slide the adjuster covers (2 pcs.) as shown in the figure below and attach them. Then, close the door.
6) Connect the copier with the desk. Connect the copier with the desk with two screws (P tight, packed together with the copier) and the fixture.
Front side
MX-DS11
Front side
Screws (P tight)
Adjuster covers
Screws (P tight)
MX-DS12
7) Remove the two screws, and remove the rear cover.
Front side
Adjuster covers
4) Remove the paper tray. Pull out the paper feed unit tray from the copier until it stops. Lift it and remove it from the copier.
8) Connect the copier (or the paper feed unit) and the desk with two screws (P tight) and two screws (S tight) packed together with the copier. When connecting, be careful of the direction of the connecting fixture of the copier.
5) Put the copier (or the paper feed unit) on the desk. Insert the positioning pins (2 pcs.) of the desk into the positioning holes of the copier (or the paper feed unit). At that time, be careful not to break the fixtures on the desk side.
Back side
Copier connecting fixture Screws (P tight)
Screws (S tight) Positioning pin Screws (P tight) Screws (S tight)
Copier connecting fixture
Copier
Fixture Be careful not to hit.
Machine stand
Positioning pin
MX-M260/M310/M260N/M310N MX-DS11/DS12 (Machine stand) 4 - 2
9) Attach the rear cover, and fix it with the two screws.
10) Install the paper tray. Install the paper tray to the original position.
MX-M260/M310/M260N/M310N MX-DS11/DS12 (Machine stand) 4 - 3
[5] MX-FN13 (Finisher)
1) Unpacking 2) Remove the paper exit tray cover as shown in the figure below.
3) Open the front cover.
When removing the finisher, put your hand beneath the unit and lift it up as shown below.
4) Remove the five screws, and remove the left cabinet.
Check to confirm that all the packed parts are provided.
FIN connection unit
FIN front cover
Paper holding arm
5) Remove the screws (3 positions) which are fixing the paper exit tray.
Second paper exit unit
Rail dummy cover
Resin grip
Harness clamp (2 pcs.) M3 x 8 S tight bind M3 x 10 S tight bind (with M3 screw) (4 pcs.) (4 pcs.)
Staple position label
MX-M260/M310/M260N/M310N MX-FN13 (Finisher) 5 - 1
6) Remove the paper exit tray by using care for the tray paper presence detection harness which is connected to the back side of the paper exit tray.
10) Remove the screw, and remove the right cabinet lever cover.
7) Insert the tray paper presence detection harness into the dummy connector on the fan duct.
11) Open the manual feed tray and the right door. Remove the two screws, and remove the right cabinet.
8) Disengage the pawls in the sequence of 1 and 2 and remove the paper exit dummy cover.
2 2 1 1
12) Pass the harness (packed together with the unit) of the second paper exit unit though inside of the frame plate as shown in the figure. Install the second paper exit unit to the machine, and fix it with the four M4 S tight screws which are packed together with the finisher. Connect the connector of the harness.
9) Remove the screw, and remove the maintenance cover. Remove the four screws, and remove the rear cabinet.
MX-M260/M310/M260N/M310N MX-FN13 (Finisher) 5 - 2
13) Install the right cabinet to the original position, and fix it with two screws. Close the right door and the manual paper feed tray.
16) Remove one round-head screw from the connection unit which is packed with the finisher, and remove the front cabinet lower and the connection cabinet temporarily.
17) Slide the rail under the connection unit to the lock position.
14) Install the rear cabinet to the original position, and fix it with four screws. Install the maintenance cover, and fix it with one screw.
18) Engage the finisher connection plate with the notch in the stay at the right bottom of the machine. Slide the connection plate to the bottom, and attach one M3 screw as shown. (Use the screw bundled to the package.) Press the right side of the connection plate.
15) Attach the rail dummy cover to the guide rail by sliding it along the guide rail in the arrow direction as shown in the figure.
19) After attaching the screw, pull the connection plate toward you.
MX-M260/M310/M260N/M310N MX-FN13 (Finisher) 5 - 3
When holding the finisher, hold the front frame side and the rear frame side.
23) Install the finisher connection cabinet from the left. (A hook pawl is provided on the back. Be careful not to float.)
20) Insert the finisher along the connection plate rail from the left side of the machine until it locks.
24) Install the finisher front cabinet lower with four screws. (First attach the A screw.) A: M3 round-head screw (1 position) Use the screw which was removed from the FIN connection unit. B: M4 P tight screws (3 positions) Use the screws which were removed from the paper exit tray of the machine.
A
21) Press the finisher from the front to slide to the rear together with the connection plate.
B
B
B
25) Install the left cabinet to the original position. (M3 screws 3 positions, M4 screws 2 positions)
22) Fix the connection plate from the front with the M3 screws (3 positions) which are packed with the finisher.
26) Install the finisher front cover from the left side by sliding, and fix the center of the fulcrum point with the resin clip.
MX-M260/M310/M260N/M310N MX-FN13 (Finisher) 5 - 4
27) Install the paper holding arm.
30) Attach the staple position label to the document feed unit.
10mm
10mm
28) Close the finisher front cover and the machine front cover.
Cleaning caution label
29) Connect the machine connection connector, and remove two mounting screws of the plate cover at the back of the machine. Attach two clamps (with screws) which are packed together with the finisher as shown in the figure, and arrange the cable.
Non LPS Do not connect to devices other than specified peripheral devices of our company.
MX-M260/M310/M260N/M310N MX-FN13 (Finisher) 5 - 5
[6] MX-TE10 (Paper exit tray)
1. Parts included
3) Insert the harness of the right paper exit unit to the hole of the second paper exit. Note: Wire the harness to the upper of the rib. If wiring it to the under of the rib, the harness may come into contact with the gear. 4) Insert the pawl of the right paper exit unit to the oval hole of the frame of the main unit. Insert the positioning boss of the main unit to the round hole in lower side.
Paper exit unit
Paper exit tray
Paper holding arm
Rib Gear Harness cover OP Paper exit right cover Right paper exit actuator
Screw (M3 x 4)
Screw (M4 x 10)
Screw (M3 x 8)
2. Installation
1) Remove two EPE cushions. 5) When tightening the screw, tighten in the sequence of 1, 2, 3 and 4.
3
1
4 2
2) Remove five screws and remove the rear cabinet. 6) Wiring
MX-M260/M310/M260N/M310N MX-TE10 (Paper exit tray) 6 - 1
7) Install the paper exit right cover sub and tightening the screw. 3 x 4 screw (S) 2PCS
9) Remove the screw and remove the paper exit fan connector sheet. 10) Install the harness cover OP and tightening the screw.
8) Install the right paper exit actuator and the paper holding arm.
Insert it to the hole of the paper exit right cover (R side, F side)
Paper holding arm
Right paper exit actuator
Insertion direction
Right paper exit paper full detection fulcrum
MX-M260/M310/M260N/M310N MX-TE10 (Paper exit tray) 6 - 2
[7] MX-TR11 (Job separator tray)
1. Parts included
3) Remove the right cabinet AS. M4 x 10 P tight (2pcs)
Job separator unit
Second paper exit tray holder
Second paper exit unit
M4 x 10 (5 pcs.)
Mylar
2. Installation
1) Remove the rear cabinet right and the rear cabinet maintenance cover.
4) Attach the mylar sheet to the bottom of the scanner.
Front side Outline of rear side Reference of square hole. Reference R end
R end
Reference Rear side
5) Install the second paper exit UN. M4 x 10 S tight (4pcs) 6) Connect the second paper exit UN connector to MCU UN. 2) Remove the right cabinet lever cover. (Dispose of the part after installation) (M4 x 12 P tight) Fixation treatment of the harness is required.
MX-M260/M310/M260N/M310N MX-TR11 (Job separator tray) 7 - 1
7) Disengage the pawls in the sequence of 1 and 2 and remove the paper exit dummy cover.
12) Install the right cabinet AS. M4 x 10 P tight (2pcs)
2 2 1 1
8) Remove the paper holding arm, install it to job separator AS. (Same as the current state)
13) Install the rear cabinet right and the rear cabinet maintenance cover.
Paper holding arm
9) Install the second paper exit tray holder. (New part) M4 P tight tightening 10) Install the job separator tray AS. 11) Install the rail dummy cover part to the guide rail so that slide the over part from front side to rear side. After that, insert the rib of tray part to the location of insertion of the second paper exit tray holder. Check that it is caught while being pushing up the tray. 14) Job separator setting in simulation 26-1.
MX-M260/M310/M260N/M310N MX-TR11 (Job separator tray) 7 - 2
[8] MX-PB12 (Printer expansion kit)
1. Parts included
3) Attach the PCL PWB unit. Attach the support post to the mounting plate of machine options. Then connect the PCL PWB connector to the mother board connector and fit the PCL PWB with the six screws with M3 spring washer (packed with the unit). CD-ROM: 1 pc. Operation manual Then, attach the USB connector portion using the supplied three screws.
PCL PWB: 1 pc.
M3 screws with spring washer
Support post
M3 screws with M3 screws: 1 pc. spring washer : 6 pcs. (For installation of (For installation of the the USB connectors) PCL PWB)
Support post: 2 pcs.
M3 screw
2. Installation procedure
Turn off the main switch of the copier and then remove the power plug of the copier from the outlet. 1) Remove the shielding plate. Remove five screws and remove the shielding plate.
PCL PWB M3 screws with spring washer
4) Attach the shielding plate. Attach the shielding plate using five screws.
Screws Screws
Screws Screws
2) Cut and remove the cut-out portion from the left rear cabinet. Cut and remove the cut-out portion of the left rear cabinet using a tool such as diagonal cutters. (Be careful about the direction of the tool so that the cut surface is flat) Insert the power plug of the copier to the outlet and turn on the main switch. Then, carry out the following procedure. 5) Check for the PCL PWB. Press the PRINT key on the operation panel to check to see if the copier enters the print mode. 6) Check for the language. Check for the language setting (26-22) following the procedure described in the service manual (section of simulation). 7) Check for printing. For installation of printer drivers on a computer, see the supplied operation manual.
Cut-out portion
Then, connect a USB cable to the computer and execute printing to check to see if printing can be executed properly.
MX-M260/M310/M260N/M310N MX-PB12 (Printer expansion kit) 8 - 1
3. Mounting of additional memory
(After mounting it, Installation proceed to step 4.) Insert the memory module until it clicks. The memory module is lock when it is inserted. However, be sure to check that the module slit is engaged with the connector rib when it is inserted.
Memory module (S.O.DIMM)
MX-M260/M310/M260N/M310N MX-PB12 (Printer expansion kit) 8 - 2
[9] AR-SM5/SM6 (256MB Expansion memory board/512MB Expansion memory board)
1. Parts included
AR-SM5 AR-SM6
256MB SDRAM memory module (168 pin DIMM): 1 pc. Installation caution sheet
512MB SDRAM memory module (168 pin DIMM): 1 pc. Installation caution sheet
2. Installation procedure
Turn off the main switch of the copier and then remove the power plug of the copier from the outlet. 1) Remove the shielding plate. Remove the screw and remove the cabinet.
2) Attach the SDRAM memory module. Attach the SDRAM memory module to CN1 and CN2 of the IMC board. When only one SDRAM memory module is used, attach it to CN1.
CN2
CN1
MX-M260/M310/M260N/M310N AR-SM5/SM6 (256MB Expansion memory board/512MB Expansion memory board) 9 - 1
[10] MX-PK10 (PS3 Expansion kit)
1. Parts included
CD-ROM: 1 License agreement Installation caution sheet
NOTE : Do not use the CD-ROM packed in MX-PK10, but use the CDROM packed together with the MX-PB12 for setting the PS driver.
2. Installation procedure
To enable the PS3, the product key must be acquired. (For the method of acquiring the product key, contact the SHARP authorized dealer.) 1) Check that MX-PB12 operates normally. · Turn on the power and wait until warming up is complete. · Press the PRINT key on the operation panel of the main unit. · If the LCD in the operation panel of the main unit switches to the print mode normally, MX-PB12 is operating normally. · If it is not operating normally, follow the MX-PB12 Installation Manual to check and modify the system configuration settings and check the operation. 2) Enable the PS3. To enable the system configuration, use the keys on the main unit to set the mode. Enter the product key with the key operator program. (Refer to the Operation Manual of Key Operator Program.) Setting of the product key is complete. To update the system, press the CA key to exit the setting mode. 3) Check the PS3. Make the following sequence of selections on the control panel. · Press Special Functions , highlight Configuration and press OK. · Use the up and down keys to highlight Test print menu and press OK. · Use the up/down keys to highlight Configuration page and press OK. A configuration page will be printed. Check that the option memory capacity is 128 MB or more. Check that the PS3 has been installed.
Please keep below important information. This information will use for other products.
APPLICATION NUMBER MACHINE SERIAL NUMBER PRODUCT KEY
MX-M260/M310/M260N/M310N MX-PK10 (PS3 Expansion kit) 10 - 1
[11] AR-PF1/PF2 (Barcode font kit/Macro font flash ROM kit)
1. Parts included
AR-PF1
CD-ROM: 1 pc. Operation manual Installation caution sheet Bar code board: 1 pc. AR-PF2
Operation manual Installation caution sheet Flash ROM board: 1 pc.
2. Installation
Turn off the main switch of the copier and then remove the power plug of the copier from the outlet. 1) Remove the shielding plate. Remove five screws and remove the shielding plate.
Screws
Screws
2) Attach the bar code board/flash ROM. Attach the bar code board/flash ROM board to CN7 of the printer board.
Bar code board/ Flash ROM board/ Font ROM board
MX-M260/M310/M260N/M310N AR-PF1/PF2 (Barcode font kit/Macro font flash ROM kit) 11 - 1
[12] MX-NSX1 (Network scanner expansion kit)
1. Packed items
This network scanner kit includes the following items in the package. · CD-ROM (Network Scanner Tool and Sharpdesk, Installer, Sharp TWAIN driver, etc.) · Installation caution sheet and Operation Manual (License numbers of 10 user clients of Sharpdesk are specified.) 2) Mount the memory module. Insert the memory module until it clicks. The memory module is lock when it is inserted. However, be sure to check that the module slit is engaged with the connector rib when it is inserted.
2. Installation procedure
To use the scanner expansion kit, a S.O.DIMM memory module (128 MB or more) is needed. If no memory is added, an S.O.DIMM module must be mounted on PCL PWB. For the mounting method and the memory capacity, see below. To enable the scanner function, the product key must be acquired. (For the method of acquiring the product key, contact the SHARP authorized dealer.) 1) Check the capacity of the Printer PWB memory. Use the keys of the copier to print the configuration page. (For details, see the operation manual.) Check that the capacity of the optional memory is 128 MB or more. 2) Enable the network scanner feature. To enable the system configuration, use the keys on the copier to set the mode. Enter the product key with the key operator program. (Refer to the Operation Manual of Key Operator Program.) Setting of the product key is completed. Press the [EXIT] key to update the system and exit the setting mode.
Screws
Memory module (S.O.DIMM)
3) Reattach the shielding plate. Reattach the shielding plate using the five screws.
3. Mounting the additional memory
Turn off the main switch of the copier and then remove the power plug of the copier from the outlet. 1) Remove the shielding plate. Remove the five screws and remove the shielding plate.
Screws
Screws
Screws
MX-M260/M310/M260N/M310N MX-NSX1 (Network scanner expansion kit) 12 - 1
[13] AR-FX7 (Facsimile expansion kit)
1. Parts included
2) Work the left rear cabinet. Cut and remove the cut-out portion from the left rear cabinet using a tool such as nippers. Be careful about the direction of the tool so that the cut surface is flat.
Cut-out portion
PWB spacers: 2 pcs. Fax PWB: 1 pc. TEL/LIU PWB: 1 pc.
Speaker unit: 1pc.
Fax connector cover: 1 pc.
Line cable: 1 pc.
3) Attach the speaker. Attach the speaker to the left rear cabinet using supplied two golden screws (M3).
M3 screws: 2 pcs.
M3 screws with washer: 8 pcs.
Supplied label: 1 sheet
M3 screws
Installation manual: 1 sheet
Operation manuals: 1 pc.
2. Installation procedure
Turn off the main switch of the copier and then remove the power plug of the copier from the outlet. 1) Remove the shielding plate and the left rear cabinet. Remove the five screws that fix the shielding plate and then remove the shielding plate by inserting a flat-blade screwdriver. Then, remove the two screws that secure the left rear cabinet and slide the cabinet toward the rear side of the main unit to remove it. 4) Attach the fax PWB Mount the two spacers on the fax PWB. Then, insert the connector of the FAX PWB to the connector of the FAX expansion PWB and secure it using six M3 screws with washer.
M3 Screws with washer
Fax PWB
Shielding plate Screws Screws Left rear cabinet
Spacers
M3 Screws with washer
MX-M260/M310/M260N/M310N AR-FX7 (Facsimile expansion kit) 13 - 1
5) Attach the TEL/LIU PWB. Insert the connector of the TEL/LIU PWB to the connector of the FAX PWB, fit two spacers to the TEL/LIU PWB, and attach the TEL/LIU PWB using two M3 screws with washer.
8) Reattach the shielding plate. Fit the pawls of the shielding plate to the main unit and secure the plate using five screws.
Spacers TEL/LIU PWB
Screws
M3 Screws with washer
Shielding plate
Insert the power plug of the copier to the outlet and turn on the main switch. Then, carry out the following procedure. 9) Paste the label on the left rear cabinet of the copier. Paste the FCC label to the position shown in the illustration. In order to manifest the compliance with FCC Part 68 and IC CS-03, it is required to provide the machine with the FCC Registration Number (USA), Ringer Equivalence (USA) and Ringer Equivalence (Canada). After installing the FAX expansion kit in the machine, please put the registration label, packed with the kit, on the prescribed location.
6) Reattach the left rear cabinet. <1> Pass the speaker harness through the hole of the frame of the fax expansion PWB and connect it to the connector of the fax PWB. <2> Fit the pawls of the left rear cabinet to the mounting portions of the main unit. Slide the cabinet toward the front of the main unit to attach it. <3> Secure the left rear cabinet using two screws. <4> Attach the supplied fax connector cover.
Speaker harness
Screws
Left rear cabinet
FCC label
Fax connector cover
10) Clear the image memory. If an extended memory (AR-MM9) has been mounted in step 7, be sure to carry out this step. If no extended memory has been mounted, this step is not necessary. <1> [P], [], [C], and [] to enter the simulation mode. <2> Use the 10-key pad to enter "66" in the main code entry screen shown below and press the START key.
Screw Pawls
If you need not to mount an extended memory, proceed to step 8. 7) Mount an additional memory (AR-MM9) Insert the additional memory into the socket on the FAX PWB.
<3> Use the 10-key pad to enter "10" in the sub-code entry screen shown below.
MX-M260/M310/M260N/M310N AR-FX7 (Facsimile expansion kit) 13 - 2
<4> Use the 10-key pad to enter "1" in the submenu screen shown below and press the START key.
<5> The screen shown below is displayed and memory clear operation is executed to restart the main unit.
<6> After several minutes, memory clear operation is completed and then the screen shown below is displayed. Press the Reset key to restart the main unit.
11) Connect the FAX board unit line cable. Connect the line cable to the FAX board unit.
Line cable
MX-M260/M310/M260N/M310N AR-FX7 (Facsimile expansion kit) 13 - 3
[14] MX-FR17U/FR18U (Data security kit)
· This installation manual is provided for the MX-M260/M310 series. · For installation to other models, see the service manual. For improvement of workability, part of the description in this manual may be modified without prior notice.
Parts included
MCU ROM: 1 pc.
3) Replace the MCU ROM. Push the lock release lever of CN500 to remove the ROM PWB. Then, giving attention to the insertion direction of the supplied MCU ROM PWB, push the PWB in until it locks.
FAX ROM: 1 pc. ("320xx O" is printed on the IC1 label.)
CN1
Lock release lever CN11
IMC PWB for security: 1 pc.
PCL ROM: 1 pc. ("VH129L" is printed on the IC3 label.)
CN500
MCU ROM PWB
· To enable the data security function, the product key must be acquired. The information used for acquiring the product key is on the cover page of English operational manual. (For the method of acquiring the product key, contact the dealer.) Note: If image data remains before installation of the data security kit, be sure to output or clear the data in advance. Note that image data that has not been output before installation cannot be output after installation. Turn off the main switch of the main unit and remove the power plug of the main unit from the outlet. 1) Remove the rear cabinet and the shielding plate. Remove the screw and then remove the left cover of the rear cabinet. Then, remove the four screws and then remove the rear cabinet. Remove the five screws and then remove the shielding plate.
Screw CN13
CN13
CAUTION: Cutout
4) Replace the PCL ROM. When installing this kit to a main unit on which the PCL PWB is not mounted, proceed to step 5. Push up the lock release lever of CN13 and remove the ROM PWB. Then, giving attention to the insertion direction of the supplied PCL ROM PWB, push the PWB in until it locks.
PCL ROM PWB Lock release lever
CAUTION: Cutout
Rear cabinet Screws
5) Replace the FAX ROM. When installing this kit to a main unit on which the FAX PWB is not mounted, proceed to step 6. Push up the lock release lever of CN11 and remove the ROM PWB. Then, giving attention to the insertion direction of the supplied FAX ROM PWB, push the PWB in until it locks.
Screw Screw Left cover
Screws Screws Shielding plate
2) Replace the IMC PWB to the one for security. Remove the four screws that secure the IMC PWB. Remove the IMC PWB while narrowing the head of the spacer. Connect the connector of the supplied IMC PWB to the connector of the MCU PWB of the main unit and fit the spacer. Then, use the four M3 x 8 screws that have been removed to secure the IMC PWB.
Connector of MCU PWB M3 x 8 screws
CN11
Lock release lever
CAUTION: Cutout
FAX ROM PWB
Spacer IMC PWB
M3 x 8 screws
MX-M260/M310/M260N/M310N MX-FR17U/FR18U (Data security kit) 14 - 1
6) Reattach the shielding plate and the rear cabinet. Fit the two pawls at the upper part of the shielding plate to the main unit and secure the plate with the five screws. Then, reattach the rear cabinet to its original position and secure it with the four screws. Reattach the left cover of the rear cabinet to the rear cabinet and secure it with the screw.
M3 x 8 S Tite Pawls Shielding plate
Rear cabinet M3 x 8 machine screws
M4 x 10 S Tite M3 x 8 machine screw Left cover Left cover
M3 x 8 machine screws
Insert the power plug of the main unit to the outlet and turn on the main switch of the main unit. Then, carry out the following procedure. · To enable the data security function, use the keys on the operation panel to enter the product key and turn off the power and then on again. If a key mark is displayed on the job status screen on the operation panel, the security function is enabled.
key mark
· If the fax expansion kit (AR-FX7) and/or the printer expantion kit (MX-PB12) is not already installed, give the customer the enclosed FAX ROM PWB and/or PCL ROM PWB. The customer is required to enable the data security function after purchasing these kits.
MX-M260/M310/M260N/M310N MX-FR17U/FR18U (Data security kit) 14 - 2
[15] MX-AMX1 (Application integration module)
1. Unpacking
A. Check the packed items
1
No. 1 2 3 CD-ROM
2
Names of bundles
3
Quantity 1 1 1
MX-AMX1 GETTING STARTED GUIDE Sharpdesk license kit Operation Manual
2. Installation
To enable the Application Integration Module function, the product key must be acquired.
A. Make preparations to enable the Application Integration Module function
1) To enable the Application Integration Module function, enter the product key by the key operation of the operation panel. a) Touch [PRODUCT KEY INPUT]. b) Enter the product key with the 10-key and touch [OK] key. 2) After completion of the product key entry, turn OFF the power switch and the main power switch of the machine, and turn them ON again.
B. Check the operation of the Application Integration Module function
1) Send image data and meta data by referring to MX-AMX1 GETTING STARTED GUIDE (Package part No. 2). Check to confirm that image data and meta data are properly received.
MX-M260/M310/M260N/M310N MX-AMX1 (Application integration module) 15 - 1
COPYRIGHT 2009 BY SHARP CORPORATION
All rights reserved. Printed in Japan. No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic; mechanical; photocopying; recording or otherwise without prior written permission of the publisher.
Trademark acknowledgements
Microsoft ® Windows ® operating system is a trademark or copyright of Microsoft Corporation in the U. S.A. and other countries. Windows® 95, Windows® 98, Windows ® Me, Windows NT ® 4.0, Windows ® 2000, Windows ® XP, Windows ® Vista, Windows ® 2000 Server, Windows ® Server 2003 and Internet Explorer® are trademarks or copyrights of Microsoft Corporation in the U.S.A. and other countries. IBM and PC/AT are trademarks of International Business Machines Corporation. Acrobat ® Reader Copyright ® 1987 -2002 Adobe Systems Incorporated. All rights reserved. Adobe, the Adobe logo, Acrobat, and the Acrobat logo are trademarks of Adobe Systems Incorporated. All other trademarks and copyrights are the property of their respective owners.
SHARP CORPORATION Business Solution Group CS Promotion Center Yamatokoriyama, Nara 639-1186, Japan
2009 August Printed in Japan