Text preview for : MX-B201 - MX-B201D SERVICE MANUAL.pdf part of Sharp MX-B201 MX-B201 - MX-B201D SERVICE MANUAL
Back to : MX-B201 - MX-B201D SERVIC | Home
1 '11/Oct/17
SERVICE MANUAL
CODE: 00ZMXB201DS2E
DIGITAL MULTIFUNCTIONAL SYSTEM
MODEL
1
MX-B201 MX-B201D
MX-B201 MX-B201D
1
CONTENTS
[1] [2] [3] [4] [5] [6] [7] [8] [9] [10] [11] [12] [13] [14] [15] [16]
GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 1 SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 1 CONSUMABLE PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 1 EXTERNAL VIEWS AND INTERNAL STRUCTURES . . . . . . . . . 4 - 1 UNPACKING AND INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . 5 - 1 COPY PROCESS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 - 1 OPERATIONAL DESCRIPTIONS . . . . . . . . . . . . . . . . . . . . . . . . . 7 - 1 DISASSEMBLY AND ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . 8 - 1 ADJUSTMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 - 1 SIMULATION, TROUBLE CODES . . . . . . . . . . . . . . . . . . . . . . . 10 - 1 MAINTENANCE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 - 1 USER PROGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 - 1 ELECTRICAL SECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 - 1 CIRCUIT DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 - 1 FLASH ROM VERSION UP PROCEDURE. . . . . . . . . . . . . . . . . 15 - 1 UPDATING NETWORK BOARD FIRMWARE . . . . . . . . . . . . . . . 16 - 1
Parts marked with " " are important for maintaining the safety of the set. Be sure to replace these parts with specified ones for maintaining the safety and performance of the set.
SHARP CORPORATION
This document has been published to be used for after sales service only. The contents are subject to change without notice.
CAUTION
This product is a class 1 laser product that complies with 21CFR 1040 of the CDRH standard and IEC825. This means that this machine does not produce hazardous laser radiation. The use of controls, adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. This laser radiation is not a danger to the skin, but when an exact focusing of the laser beam is achieved on the eye's retina, there is the danger of spot damage to the retina. The following cautions must be observed to avoid exposure of the laser beam to your eyes at the time of servicing. 1) When a problem in the laser optical unit has occurred, the whole optical unit must be exchanged as a unit, not as individual parts. 2) Do not look into the machine with the main switch turned on after removing the developer unit, toner cartridge, and drum cartridge. 3) Do not look into the laser beam exposure slit of the laser optical unit with the connector connected when removing and installing the optical system. 4) The middle frame contains the safety interlock switch. Do not defeat the safety interlock by inserting wedges or other items into the switch slot.
CAUTION
INVISIBLE LASER RADIATION, WHEN OPEN AND INTERLOCKS DEFEATED. AVOID EXPOSURE TO BEAM.
VARO !
AVATTAESSA JA SUOJALUKITUS OHITETTAESSA OLET ALTTIINA NÄKYMÄTTÖMÄLLE LASERSÄTEILYLLE ÄLÄ KATSO SÄTEESEEN.
VORSICHT
UNSICHTBARE LASERSTRAHLUNG, WENN ABDECKUNG GEÖFFNET UND SICHERHEITSVERRIEGELUNG ÜBERBRÜCKT. NICHT DEM STRAHL AUSSETZEN. LASER WAVE LENGTH : 770 795nm Pulse times : 10.24sec Out put power : 0.15mW ± 0.01mW
ADVARSEL
USYNLIG LASERSTRÅLNING VED ÅBNING, NÅR SIKKERHEDSBRYDERE ER UDE AF FUNKTION. UNDGÅ UDSAETTELSE FOR STRÅLNING.
VARNING !
OSYNLIG LASERSTRÅLNING NÄR DENNA DEL ÄR ÖPPNAD OCH SPÄRREN ÄR URKOPPLAD. BETRAKTA EJ STRÅLEN. STRÅLEN ÄR FARLIG.
At the production line, the output power of the scanner unit is adjusted to 0.57 MILLI-WATT PLUS 20 PCTS and is maintained constant by the operation of the Automatic Power Control (APC). Even if the APC circuit fails in operation for some reason, the maximum output power will only be 15 MILLI-WATT 0.1 MICRO-SEC. Giving and accessible emission level of 42 MICRO-WATT which is still-less than the limit of CLASS-1 laser product.
Caution This product contains a low power laser device. To ensure continued safety do not remove any cover or attempt to gain access to the inside of the product. Refer all servicing to qualified personnel.
VAROITUS! LAITTEEN KÄYTTÄMINEN MUULLA KUIN TÄSSÄ KÄYTTÖOHJEESSA MAINITULLA TAVALLA SAATTAA ALTISTAA KÄYTTÄJÄN TURVALLISUUSLUOKAN 1 YLITTÄVÄLLE NÄKYMÄTTÖMÄLLE LASERSÄTEILYLLE.
VARNING - OM APPARATEN ANVÄNDS PÅ ANNAT SÄTT ÄN I DENNA BRUKSANVISNING SPECIFICERATS, KAN ANVÄNDAREN UTSÄTTAS FÖR OSYNLIG LASERSTRÅLNING, SOM ÖVERSKRIDER GRÄNSEN FÖR LASERKLASS 1.
The foregoing is applicable only to the 220V model, 230V model and 240V model.
LUOKAN 1 LASERLAITE KLASS 1 LASER APPARAT
CONTENTS
[1] [2] GENERAL 1. Major functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 SPECIFICATIONS 1. Basic Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1 2. Operation specifications. . . . . . . . . . . . . . . . . . . . . . . . 2-1 3. Copy performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2 4. SPLC printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3 5. Scan function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3 6. RSPF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3 [3] CONSUMABLE PARTS 1. Supply system table. . . . . . . . . . . . . . . . . . . . . . . . . . . A. Asia . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B. SMEF/Dealer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C. SRH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D. Europe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E. North America . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1 3-1 3-1 3-1 3-1 3-1 [7] OPERATIONAL DESCRIPTIONS 1. Outline of operation . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-1 2. Scanner section. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-2 A. Scanner unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-2 B. Optical system . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-2 C. Drive system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-2 3. Laser unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-3 A. Basic structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-3 B. Laser beam path . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-3 C. Composition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-3 4. Fuser section. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-3 A. General description. . . . . . . . . . . . . . . . . . . . . . . . . .7-4 5. Paper feed section and paper transport section . . . . . .7-4 A. Paper transport path and general operations . . . . . .7-4 6. RSPF section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-7 A. Outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-7 B. Document transport path and basic composition . . .7-7 C. Operational descriptions . . . . . . . . . . . . . . . . . . . . . .7-7 D. RSPF open/close detection (book document detection) . . . . . . . . . . . . . . . . . . . .7-8 7. D-D (Duplex to Duplex) mode paper/document transport (Duplex model) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-8 A. Initial state. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-8 B. Front copy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-8 C. Back copy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-9 8. Shifter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-9 [8] DISASSEMBLY AND ASSEMBLY 1. High voltage section . . . . . . . . . . . . . . . . . . . . . . . . . . .8-1 A. List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-1 B. Disassembly procedure . . . . . . . . . . . . . . . . . . . . . .8-1 C. Assembly procedure . . . . . . . . . . . . . . . . . . . . . . . . .8-1 D. Charger wire cleaning . . . . . . . . . . . . . . . . . . . . . . . .8-1 E. Charger wire replacement. . . . . . . . . . . . . . . . . . . . .8-2 2. Operation panel section . . . . . . . . . . . . . . . . . . . . . . . .8-2 A. List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-2 B. Disassembly procedure . . . . . . . . . . . . . . . . . . . . . .8-2 C. Assembly procedure . . . . . . . . . . . . . . . . . . . . . . . . .8-3 3. Optical section. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-3 A. List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-3 B. Disassembly procedure . . . . . . . . . . . . . . . . . . . . . .8-3 C. Assembly procedure . . . . . . . . . . . . . . . . . . . . . . . . .8-5 4. Fusing section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-5 A. List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-5 B. Disassembly procedure . . . . . . . . . . . . . . . . . . . . . .8-5 C. Assembly procedure . . . . . . . . . . . . . . . . . . . . . . . . .8-8 5. Tray paper feed/transport section . . . . . . . . . . . . . . . . .8-8 A. List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-8 B. Disassembly procedure . . . . . . . . . . . . . . . . . . . . . .8-8 C. Assembly procedure . . . . . . . . . . . . . . . . . . . . . . . .8-13 6. Manual paper feed section . . . . . . . . . . . . . . . . . . . . .8-14 A. List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-14 B. Disassembly procedure . . . . . . . . . . . . . . . . . . . . .8-14 C. Assembly procedure . . . . . . . . . . . . . . . . . . . . . . . .8-15 D. Pressure plate holder attachment . . . . . . . . . . . . . .8-15 7. Rear frame section . . . . . . . . . . . . . . . . . . . . . . . . . . .8-16 A. List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-16 B. Disassembly procedure . . . . . . . . . . . . . . . . . . . . .8-16 C. Assembly procedure . . . . . . . . . . . . . . . . . . . . . . . .8-16
2. Environmental . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2 3. Production control number (lot No.) identification . . . . 3-2 4. Toner cartridge replacement . . . . . . . . . . . . . . . . . . . . 3-3 [4] EXTERNAL VIEWS AND INTERNAL STRUCTURES 1. Appearance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1 2. Internal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1 3. Operation panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2 4. Motors and solenoids. . . . . . . . . . . . . . . . . . . . . . . . . . 4-3 5. Sensors and switches . . . . . . . . . . . . . . . . . . . . . . . . . 4-4 6. PWB unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5 7. Cross sectional view . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6 [5] UNPACKING AND INSTALLATION 1. Copier installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1 2. Cautions on handling . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1 3. Checking packed components and accessories . . . . . 5-1 4. Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2 5. Removing protective packing materials . . . . . . . . . . . . 5-2 6. Developer unit installation . . . . . . . . . . . . . . . . . . . . . . 5-2 7. Toner cartridge installation. . . . . . . . . . . . . . . . . . . . . . 5-3 8. Loading paper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3 9. Software. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A. Before installation . . . . . . . . . . . . . . . . . . . . . . . . . . B. Installing the software . . . . . . . . . . . . . . . . . . . . . . . C. Setting up Button Manager . . . . . . . . . . . . . . . . . . . 5-4 5-4 5-5 5-8
10. Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-9 11. Moving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-9 12. Scanner moisture-proof kit. . . . . . . . . . . . . . . . . . . . . . 5-9 A. Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-9 B. Precautions at installation . . . . . . . . . . . . . . . . . . . . 5-9 C. Attachment method . . . . . . . . . . . . . . . . . . . . . . . . 5-10 [6] COPY PROCESS 1. Functional diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1 2. Outline of print process . . . . . . . . . . . . . . . . . . . . . . . . 6-2 3. Actual print process . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2
1 '11/Oct/17
8. Power section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A. List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B. Disassembly procedure . . . . . . . . . . . . . . . . . . . . . C. Assembly procedure . . . . . . . . . . . . . . . . . . . . . . .
1
8-17 8-17 8-17 8-17 8-17 8-17 8-17 8-17 8-17 8-17 8-17 8-17 8-18 8-18 8-18 8-18 8-18 8-18 8-19 8-20 8-20 8-21 8-21 8-22 8-22 8-22 8-23
[13] ELECTRICAL SECTION 1. Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13-1 A. Overall block diagram . . . . . . . . . . . . . . . . . . . . . . .13-1 2. Actual wiring diagram . . . . . . . . . . . . . . . . . . . . . . . . .13-2 A. MCU PWB. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13-2 B. RSPF unit (MX-B201: Option, MX-B201D: Option or Standard (due to sales area)) . . . . . . . . . . . . . . . . .13-3 C. 2nd CASSETTE (Option) . . . . . . . . . . . . . . . . . . . .13-3 D. ANB, FAX (Option) . . . . . . . . . . . . . . . . . . . . . . . . .13-4 3. Signal name list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13-5 [14] CIRCUIT DIAGRAM 1. MCU PWB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14-1 2. OPERATION PWB . . . . . . . . . . . . . . . . . . . . . . . . . .14-15 [15] FLASH ROM VERSION UP PROCEDURE 1. Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15-1 2. Download procedure . . . . . . . . . . . . . . . . . . . . . . . . . .15-1 3. Installation procedure . . . . . . . . . . . . . . . . . . . . . . . . .15-3 A. USB joint maintenance program installation . . . . . .15-3 B. Installation procedure on Windows XP . . . . . . . . . .15-3 C. Installation procedure on Windows 2000 . . . . . . . .15-4 [16] UPDATING NETWORK (FAX) BOARD FIRMWARE 1. Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16-1 2. Upgrading procedures. . . . . . . . . . . . . . . . . . . . . . . . .16-1
1
9. Duplex motor section (MX-B201D only). . . . . . . . . . . A. List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B. Disassembly procedure . . . . . . . . . . . . . . . . . . . . . C. Assembly procedure . . . . . . . . . . . . . . . . . . . . . . . 10. Reverse roller section (MX-B201D only) . . . . . . . . . . A. List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B. Disassembly procedure . . . . . . . . . . . . . . . . . . . . . C. Assembly procedure . . . . . . . . . . . . . . . . . . . . . . . 11. RSPF section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A. Front cabinet, rear cabinet . . . . . . . . . . . . . . . . . . B. Upper door unit . . . . . . . . . . . . . . . . . . . . . . . . . . . C. Document tray unit . . . . . . . . . . . . . . . . . . . . . . . . D. Upper door open/close sensor . . . . . . . . . . . . . . . E. Reverse clutch, paper exit roller . . . . . . . . . . . . . . F. Drive unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G. Shutter solenoid . . . . . . . . . . . . . . . . . . . . . . . . . . H. Pickup roller, take-up roller . . . . . . . . . . . . . . . . . . I. Paper empty sensor . . . . . . . . . . . . . . . . . . . . . . . J. PS roller. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . K. Upper transport roller . . . . . . . . . . . . . . . . . . . . . . L. Paper sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . M. Lower transport roller . . . . . . . . . . . . . . . . . . . . . . N. Paper exit sensor . . . . . . . . . . . . . . . . . . . . . . . . . [9] ADJUSTMENTS
1 1 1
1
1. Optical section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-1 A. Copy magnification ratio adjustment . . . . . . . . . . . . 9-1 B. Image position adjustment . . . . . . . . . . . . . . . . . . . 9-2 2. Copy density adjustment . . . . . . . . . . . . . . . . . . . . . . . A. Copy density adjustment timing . . . . . . . . . . . . . . . B. Note for copy density adjustment . . . . . . . . . . . . . . C. Necessary tool for copy density adjustment . . . . . . D. Features of copy density adjustment. . . . . . . . . . . . E. Copy density adjustment procedure . . . . . . . . . . . . 9-4 9-4 9-4 9-4 9-4 9-5
3. High voltage adjustment . . . . . . . . . . . . . . . . . . . . . . . 9-5 A. Main charger (Grid bias) . . . . . . . . . . . . . . . . . . . . . 9-5 B. DV bias check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-6 4. Duplex adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-6 A. Adjusting the paper reverse position in memory for duplex copying . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-6 B. Adjusting trailing edge void in duplex copy mode . . 9-6 5. RSPF scan position automatic adjustment . . . . . . . . . 9-7 6. RSPF mode sub scanning direction magnification ratio adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-8 7. Automatic black level correction . . . . . . . . . . . . . . . . . 9-8 [10] SIMULATION, TROUBLE CODES 1. Entering the simulation mode . . . . . . . . . . . . . . . . . . 10-1 2. Key rule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-1 3. List of simulations . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-1 4. Descriptions of various simulations . . . . . . . . . . . . . . 10-3 5. Trouble codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-42 A. Trouble codes list . . . . . . . . . . . . . . . . . . . . . . . . 10-42 B. Details of trouble codes . . . . . . . . . . . . . . . . . . . . 10-42 [11] MAINTENANCE 1. Maintenance table . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-1 2. Maintenance display system . . . . . . . . . . . . . . . . . . . 11-1 3. Remaining toner indication . . . . . . . . . . . . . . . . . . . . 11-1 [12] USER PROGRAM 1. User programs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-1 2. Selecting a setting for a user program . . . . . . . . . . . . 12-5
1 '11/Oct/17
[1] GENERAL
1. Major functions
Configurations
Item Model MXB201 CPM (A4) PPM (A4) Color SPCL PCL Sharp E-SORT Duplex Shifter FAX desk Scanner printer printer o o Opt o o Opt o
SB/MB 2 Tray SPF RSPF MB Opt Opt
USB o (2.0 Hispeed) o (2.0 Hispeed)
Network Opt
1
20CPM 20PPM
MXB201D
20CPM 20PPM
MB
Opt
Opt/ o *1
o
o
Opt
o
o
o
Opt
o
Opt
1
*1: Option or standard due to sales area.
Descriptions of items
CPM: PPM: SB/MB: 2 Tray: SPF: R-SPF: Color Scanner: SPCL printer: PCL printer: E-SORT: Duplex: Shifter: FAX: Sharpdesk: USB: Network: Copy speed (Copies Per Minute) Print speed (Print Per Minute) SB = Manual feed single bypass, MB = Manual feed multi-bypass Second cassette unit. Original feed unit Duplex original feed unit Color scanner function SPCL printer function with USB PCL printer function Electronic sort function Auto duplex copy/print function Job separator function FAX function. Scanner utilities Interface port (USB) Network
Descriptions of table
o : Standard provision : No function or no option available Opt: Option
MX-RP13
1
MX-NB11
1
MX-B201/B201D MX-CS10
1
MX-FX12
MX-B201/B201D GENERAL 1 - 1
1 '11/Oct/17
[2] SPECIFICATIONS
1. Basic Specifications
Item Type Copy system Segment (class) Copier dimensions Desktop Dry, electrostatic Digital personal copier 518mm (W) x 460mm (D) x 298mm (H) (20-3/8" (W) x 18-1/8" (D) x 11-3/4"(H)) 518mm (W) x 460mm (D) x 298mm (H) (20-3/8" (W) x 18-1/8" (D) x 11-3/4"(H)) 518mm (W) x 460mm (D) x 376mm (H) (20-3/8" (W) x 18-1/8" (D) x 14-3/4"(H)) 16.3kg (35.9 lbs.) 16.3kg (35.9 lbs.) Not including toner cartridges. 18.9kg (41.7lbs.)
1
MX-B201 MX-B201D MX-B201 MX-B201D
OC Model RSPF Model OC Model RSPF Model
1
Weight (Approximately)
2. Operation specifications
Paper feed section Section, item Paper feed system AB system Tray paper feed section Details 1 tray (250 sheet) + multi-bypass (50 sheet) Paper size Paper weight Paper feed capacity Kinds Remark Paper size Paper weight Paper feed capacity Kinds Remark Paper size Paper weight Paper feed capacity Kinds Remark Paper size Paper weight Paper feed capacity Kinds Remark Paper exit section Originals Exit way Capacity of output tray Original set Max. original size Original kinds Original size detection Scanning system CCD sensor Lighting lamp A4, B5, A5 (Landscape) 56 - 80g/m2 (15 - 21 lbs.) 250 sheets Standard paper, specified paper, recycled paper User adjustment of paper guide available Max, feedable size: A4 / Min, feedable size: 89 x 140mm 56 - 128g/m2 (15 - 34.5 lbs.) 50 sheets (80g/m2) Standard paper, specified paper, recycled paper, OHP, Label, (Single copy) User adjustment of paper guide available 8-1/2" x 14", 8-1/2" x 13", 8-1/2" x 11", 8-1/2" x 5-1/2" (Landscape) 15 - 21 lbs. 250 sheets Standard paper, specified paper, recycled paper User adjustment of paper guide available Max, feedable size: 8-1/2" x 14" / Min, feedable size: 3.87" x 5.83" 15 - 34.5 lbs. 50 sheets (80g/m2) Standard paper, specified paper, recycled paper, OHP, Label, Envelope (Single copy) User adjustment of paper guide available Face down 200 sheets Center Registration (left edge) A4 (8-1/2" x 14") sheet, book None 3 CCDs (RGB) sensor scanning by lighting white lamp 600 dpi CCFL 560Vrms 2.8W Output: R, G, B 1 or 8 bits/pixel / Input: A/D 16 bits (12 bits actual) Writing to OPC drum by the semiconductor laser 600 dpi
Multi-bypass paper feed section
Inch system
Tray paper feed section
Multi-bypass paper feed section
Optical section
Scanning section
Resolution Type Voltage Power consumption
Output data Writing section Writing system Laser unit
Resolution
MX-B201/B201D SPECIFICATIONS 2 - 1
Image forming
Section, item Photoconductor Charger
Fusing section
Developing Cleaning Fusing system Upper heat roller Lower heat roller Heater lamp
Details Type Life Charging system Transfer system Separation system Developing system Cleaning system Type Type Type Voltage Power consumption Voltage Frequency Max. Average (during copying) Average (stand-by) Pre-heat mode
Electrical section
Power source Power consumption
OPC (30ø) 25k Saw-tooth charging with a grid, / (-) scorotron discharge (+) DC corotron system (-) DC corotron system Dry, 2-component magnetic brush development system Counter blade system (Counter to rotation) Heat roller system Teflon roller Silicon rubber roller Halogen lamp 120V / 220 - 240V 800W 120V / 220 - 240V Common use for 50 and 60Hz Less than 1000W 380Wh/H or less 80Wh/H or less 28Wh/H or less
3. Copy performance
Copy ratio Section, item Document glass Details Variable: 25% to 400% in 1% increments (total 376 steps) Fixed: AB System: 25%, 50%, 70%, 86%, 100%, 141%, 200%, 400% INCH System: 25%, 50%, 64%, 78%, 100%, 129%, 200%, 400% Variable: 50% to 200% in 1% increments (total 151 steps) Fixed: 50%, 70%, 86%, 100%, 141%, 200% (50%, 64%, 78%, 100%, 129%, 200%) 5 steps 8.0 seconds (When user program 24 is set to OFF) 10.7 seconds (paper: A4 (8-1/2" x 11"), exposure mode: AUTO, copy ratio: 100%) 20 20 99 1 - 4mm 4mm or less 0.5mm or more (per side) 4.5mm or less (total of both sides) same size: 3.0mm or less (OC) / 4mm or less (RSPF) Enlarge: 1.5mm or less (OC) / 3mm or less (RSPF) Warm-up time Reduction (50%): 6.0mm or less (OC) / 8mm or less (RSPF) ---
RSPF
Manual steps (Text, Photo) Copy speed (CPM) First-copy time *1 (Approximately) AB system A4 (Landscape) Inch system 8-1/2" x 11" (Landscape) Max. continuous copy quantity Void Void area Same size Same size
Leading edge Trailing edge Side edge void area Leading edge
Image loss
*1: The first-copy time is measured after the power save indicator turns off following power on, using the document glass with the polygon rotating in the copy ready state and "Selection of copy start state" set to ON in the user programs (A4 (8-1/2" x 11"), paper fed from paper tray). The first-copy time may vary depending on machine operating conditions and ambient conditions such as temperature.
MX-B201/B201D SPECIFICATIONS 2 - 2
1 '11/Oct/17
4. SPLC printer
Print speed First print time Duplex ROPM CPU Memory Interface Network Emulation MIB support Resolution Supported OS WHQL support Application *1: Engine Resolution *2: Running change Max. 20ppm (Paper size: A4/Letter, excluding manual paper feed) * Varies depending on the PC performance. 8 sec. (without data transfer time) Yes (MX-B201D only) Yes None 64MB USB2.0 (Hi Speed) Option SPLC (JBIG GDI) No 600dpi *1 Windows 2000, Windows XP/XPx64, Windows Vista/Vistax64, Windows 7/7x64 Yes *2 Status window
1
5. Scan function
Type Scanning system Light source Resolution Originals Output data Scan range Scan speed Protocol Interface Scanner utility Scan key/lamp Duplex scan Supported OS Void area WHQL supported Flat Bed Color Scanner Original table/RSPF 3 CCDs (RGB) sensor scanning by lighting white lamp (1 pcs of CCFL) Optical: 600 x 600dpi Setting range: 50 - 9600dpi (Preview resolution is fixed at 75dpi) Sheet type / Book type R, G, B 1 or 8 bits/pixel OC / RSPF : 8.5" (H) x 14.0" (V) Original position: Left Center OC / RSPF : Max. 2.88ms/line TWAIN / WIA (XP, Vista, 7) / STI USB 2.0 (Hi speed support) Button Manager / Sharpdesk / Composer Yes Yes (MX-B201D only) Windows 2000 Professional, Windows XP Home Edition/Professional, Windows Vista, Windows 7 *1 No (User settable by PC) Yes *2
1 1
1
*1: 32 bit and 64 bit are supported for Windows Vista, Windows 7, and Windows XP, Server 2003, Server 2008. *2: By running change
6. RSPF
Original capacity Original size Original replacement speed 50 sheets (56 - 90g/m2) or 6.5mm, 1/4" or less. A4 to A5 / 8-1/2" x 14" to 5-1/2" x 8-1/2" (Landscape) A4 / 8-1/2" x 11" 13 sheets/min. (600 x 300dpi) 7 sheets/min. (600 x 600dpi) S to S 17cpm (85% Original conversion rate) (A4/8.5" x 11" 10 originals, 5 copies) S to D 12cpm (60% Original conversion rate) (A4/8.5" x 11" 10 originals, 5 copies) D to D 8cpm (40% Original conversion rate) (A4/8.5" x 11" 10 originals (20 faces), 5 copies) Face up 56 - 90g/m2 (15 - 23.9lbs.) No Thermal paper, punched paper, folded paper, stapled paper, clipped paper, taped paper, paper with correction fluid, transparent originals such as OHP films, photos, and catalog pages.
1 1 1
Job speed (Tray 1, Landscape) Original placement Original weight Mixed feeding Unacceptable originals
1
[Conditions] Speed with tray 1, normal size, paper size of A4 (8.5" x 11"), and RSPF.
MX-B201/B201D SPECIFICATIONS 2 - 3
1 '11/Oct/17
[3] CONSUMABLE PARTS
1. Supply system table
A. Asia
No. 1 Name Toner cartridge (Black) Content Toner cartridge x 1 (Black toner: Net 243g) IC-Chip: Yes Stirring function: Yes Developer x 1 (Black developer: Net 170g) OPC drum x 1 Drum fixing plate x 1 Life 8K (A4 6% Document) 25K 25K Product name MX-B20AT1 Package 10
2 3
Developer (Black) Drum
MX-B20AV1 AR-152DR
10 10
B. SMEF/Dealer
No. 1 Name Toner cartridge (Black) Content Toner cartridge x 1 (Black toner: Net 243g) IC-Chip: Yes Stirring function: Yes Developer x 1 (Black developer: Net 170g) OPC drum x 1 Drum fixing plate x 1 Life 8K (A4 6% Document) 25K 25K Product name MX-B20FT1 Package 10
2 3
Developer (Black) Drum
MX-B20AV1 AR-152DR
10 10
C. SRH
No. 1 Name Toner cartridge (Black) Content Toner cartridge x 1 (Black toner: Net 243g) IC-Chip: Yes Stirring function: Yes Developer x 1 (Black developer: Net 170g) OPC drum x 1 Drum fixing plate x 1 Life 8K (A4 6% Document) 25K 25K Product name MX-B20AT1 Package 10
2 3
Developer (Black) Drum
MX-20AV1 AR-152DR-C
10 10
D. Europe
No. 1 Name Toner cartridge (Black) Content Toner cartridge x 1 (Black toner: Net 243g) IC-Chip: Yes Stirring function: Yes Developer x 1 (Black developer: Net 170g) OPC drum x 1 Drum fixing plate x 1 Life 8K (A4 6% Document) 25K 25K Product name MX-20GT1 Package 10
2 3
Developer (Black) Drum
MX-20GV1 AR-152DM
10 10
E. North America
No. 1 Name Toner cartridge (Black) Content Toner cartridge x 1 (Black toner: Net 243g) IC-Chip: Yes Stirring function: Yes Developer x 1 (Black developer: Net 170g) OPC drum x 1 Drum fixing plate x 1 Life 8K (A4 6% Document) 25K 25K Product name MX-B20NT1 Package 10
2
1
Developer (Black) Drum
MX-B20NV1 AR-152DR
10 10
3
MX-B201/B201D CONSUMABLE PARTS 3 - 1
1 '11/Oct/17
2. Environmental
The environmental conditions for assuring the copy quality and the machine operations are as follows:
3. Production control number (lot No.) identification
(1)
Normal operating condition
Temperature: 20°C to 25°C Humidity: 65 ± 5%RH
(2)
Acceptable operating condition
Humidity (RH) 85% 60%
: Model name : Color code : Destination : Skating : Production place : Production date (YYYYMMDD) : Serial number : Version number
20%
10°C
(3) Transportation condition
30°C
35°C
Humidity (RH) 90%
Production control label attachment position
1
60%
15%
25°C
(4) Supply storage condition
30°C
40°C
1 2 3 4 5 6 7 8 9 10
Humidity (RH) 90%
The lot number is of 10 digits. Each digit indicates the content as follows. The number is printed on the flange on the front side. 1: 2: 3: Number For this model, this digit is 2. Alphabet Indicates the model conformity code. Number Indicates the end digit of the production year. Number or X, Y, Z Indicates the production month. X stands for October, Y November, and Z December. Number Indicates the day of the production date. Number Indicates the day of the month of packing. X stands for October, Y November, and Z December. Number Indicates the day of the packing date. Alphabet Indicates the production factory.
20%
4:
5°C
45°C
5/6: 7:
8/9: 10:
MX-B201/B201D CONSUMABLE PARTS 3 - 2
Sub lot Production day Production month End digit of year Production place
4. Toner cartridge replacement
1) Open the front and side cabinets of the copier. 2) Keep holding Toner lever, and push down. 3) Carefully pull out Toner unit from the copier.
2
3 1
4) Put Toner unit in a collection bag immediately after removing it from the copier
Note: Never carry exposed Toner unit. Be sure to put it in the collection bag.
MX-B201/B201D CONSUMABLE PARTS 3 - 3
[4] EXTERNAL VIEWS AND INTERNAL STRUCTURES
1. Appearance
RSPF Original guides Document feeder cover Exit area Document feeder tray Interface 14
USB connector 1 2 3 4 12
1 4 7 10 13 Document glass Paper tray Bypass tray paper guides Paper output tray extension Power cord socket 2 5 8 11 14 Operation panel Side cover Original output tray extension Power switch Paper holder arm 3 6 9 12
5 6 7
8 9 10 11 12 13
Front cover Side cover open button Paper output tray Handles
2. Internal
Toner cartridge
Photoconductive drum
2
3
1
4 5
1 4
Front cover Transfer charger
2 5
Side cover Charger cleaner
3
Fusing unit release lever
MX-B201/B201D EXTERNAL VIEWS AND INTERNAL STRUCTURES 4 - 1
1 '11/Oct/17
3. Operation panel
1 2 3 4 5
6 7
8 9 10 11
12 13 14
15
Display
16
17
READY TO COPY. 100% A4
0
18
19
20
21
1
[MODE SELECT] key / Mode indicators Press this key to select the mode. The indicator of the selected mode lights (copy, printer, scanner, fax mode indicators). Numeric keys Use these to enter the number of copies and other numerical settings. The keys can also be used to select items in function setting menus. Power save indicator This lights up when the power save function is activated. Error indicator This lights steadily or blinks when a paper misfeed or other error occurs. Tray location indicator Indicates the selected paper tray. The indicator blinks when the tray is out of paper or is not closed. [2-SIDED COPY ( [2-SIDED SCAN ( )] key (MX-B201D) )] key (MX-B201)
2
3
4
Display This shows messages indicating the machine status and any problems that occur, as well as user programs and function setting menus. [CLEAR] key ( ) Use this to clear the set number of copies, as well as cancel a job that is in progress. When a setting menu appears, use this key to move back to the previous menu level. RSPF indicator This lights up when an original is placed in the RSPF. [TRAY SELECT] key ( ) Use to select the paper tray that has the desired paper for copying. [MENU] key Press this key to select the paper size for copying, to configure a user program or to display the total count. [E-SORT/SP.FUN ( )] key Press to select the sort function, 2 IN 1 copy function, ID CARD COPY or margin shift function.
5 7
6 8
9
10
1 1
11
12
13
15
Use to copy both sides of an original. [ ] key ( ), [ ] key ( ), [OK] key Press the [ ] key ( ) or [ ] key ( )to select an item in a function setting menu. Press the [OK] key to enter a selection. [ZOOM] key Press to select an enlargement or reduction ratio. To select a preset ratio setting, press the [ZOOM] key and select the desired preset ratio. To select a ratio that is not preset, press the [ZOOM] key, select the preset ratio that is closest to the desired ratio, and then press the [ ] key ( ) or [ ] key ( ) to increase or decrease the ratio in increments of 1%. [START] key ( ) / Ready indicator The ready indicator lights up when copying or scanning is possible. To begin copying, press the [START] key ( ). The [START] key ( ) is also pressed to return to normal operation from auto power shut-off mode. Shows the selected paper size. A checkmark " " appears when the exposure has been changed, or when two-sided copying, sort, 2 IN 1, ID CARD COPY or margin shift is selected.
14 [EXPOSURE ( )] key Use to switch from auto exposure adjustment to text mode or photo mode. 16 [CLEAR ALL] key ( ) This returns all functions to the default settings. When pressed in a setting menu, this returns the settings and display to the initial state.
17
18
Shows the current copy ratio.
19 21
20
Shows the number of copies that has been entered with the numeric keys.
MX-B201/B201D EXTERNAL VIEWS AND INTERNAL STRUCTURES 4 - 2
1 '11/Oct/17
4. Motors and solenoids
11
12 8
2
4
1
5
7 6 10 3 9
No. 1 2 3 4 5 6 7 8 9 10 11 12 Name Main motor Scanner motor Toner motor Cooling fan motor Resist roller solenoid Paper feed solenoid Multi paper feed solenoid Drive motor Duplex motor Shifter motor Reverse clutch Paper feed solenoid (RSPF) Control signal MM MRMT TM VFM RRS CPFS1 MPFS SPMT DMT SFTM SRVC SPUS Function / Operation Drives the copier. Drives the optical mirror base (scanner unit). Supplies toner. Ventilate the fuser section. Resist roller rotation control solenoid Cassette Paper feed solenoid 1 Multi manual pages feed solenoid Drives the RSPF. Devices the duplex paper transport section (Duplex model only) Drives the shifter. Reverses the rotating direction of the roller. Feeds paper.
1
MX-B201/B201D EXTERNAL VIEWS AND INTERNAL STRUCTURES 4 - 3
5. Sensors and switches
7 2 1 8
10
9
3
4
5 6
No. 1 2 3 4 5 6 7 8 9 10 Name Scanner unit home position sensor POD sensor PPD2 sensor Cassette detection switch PPD1 sensor Door switch Paper empty sensor Paper exit sensor Paper sensor Upper door open/close sensor Signal MHPS POD PPD2 CED1 PPD1 DSW SPID SRJD SPPD SCOD Type Transmission sensor Transmission sensor Transmission sensor Micro-switch Transmission sensor Micro-switch Transmission sensor Transmission sensor Transmission sensor Transmission sensor Function / Operation Scanner unit home position detection Paper exit detection Paper transport detection 2 Cassette installation detection Paper transport detection 1 Door open/close detection (safety switch for 24V) Paper entry detection Paper exit detection Paper transport detection Cover open/close detection Output "H" at home position "H" at paper pass "L" at paper pass "H" at cassette insertion "L" at paper pass 1 or 0V of 24V at door open "H" paper empty "H" paper empty "H" paper empty "L" open
MX-B201/B201D EXTERNAL VIEWS AND INTERNAL STRUCTURES 4 - 4
6. PWB unit
5 1
2
8
6
9 4 3 7
No. 1 2 3 4 5 6 7 8 9 Name Exposure lamp invertor PWB Main PWB (MCU) Operation PWB High voltage PWB CCD sensor PWB LSU motor PWB TCS PWB LSU PWB Power PWB Function / Operation Exposure lamp (CCFL) control Copier control Operation input/display High voltage control For image scanning For polygon motor drive For toner sensor control For laser control AC power input, DC voltage control
MX-B201/B201D EXTERNAL VIEWS AND INTERNAL STRUCTURES 4 - 5
7. Cross sectional view
3 18 5 15 16 17
1
2
4 19 20
6 7 8 9 10
14
No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Name Scanner unit Exposure lamp LSU (Laser unit) Paper exit roller Main charger Heat roller Pressure roller Drum Transfer unit Pickup roller Manual paper feed tray Manual paper feed roller PS roller unit Paper feed roller Pickup roller Separation roller Upper transport roller Paper exit roller Lower transport roller PS roller
13
12
11
Function / Operation Illuminates the original with the copy lamp and passes the reflected light to the lens unit (CCD). Exposure lamp (CCFL) Illuminates original Converts the original image signal into laser beams and writes onto the drum. Roller for paper exit Provides negative charges evenly to the drum surface. Fuses toner on the paper. (Teflon roller) Fuses toner on the paper. (Silicon rubber roller) Forms images. Transfers images onto the drum. Picks up the manual feed paper. (In multi feed only) Tray for manual feed paper Transport the paper from the manual paper feed port. Takes synchronization between the lead edge and the rear edge of the paper. Picks up a sheet of paper from the cassette. Picks up documents. Separates documents to feed properly. Transports of a document. Discharges documents. Transports of a document. Feeds documents to the scanning section.
MX-B201/B201D EXTERNAL VIEWS AND INTERNAL STRUCTURES 4 - 6
1 '11/Oct/17
[5] UNPACKING AND INSTALLATION
1. Copier installation
Improper installation may damage the copier. Please note the following during initial installation and whenever the copier is moved. Caution: If the copier is moved from a cool place to a warm place, condensation may form inside the copier. Operation in this condition will cause poor copy quality and malfunctions. Leave the copier at room temperature for at least 2 hours before use. Do not install your copier in areas that are: · damp, humid, or very dusty
2. Cautions on handling
Be careful in handling the copier as follows to maintain the performance of this copier. Do not drop the copier, subject it to shock or strike it against any object.
Do not expose the drum cartridge to direct sunlight. · exposed to direct sunlight Doing so will damage the surface (green portion) of the drum cartridge, causing poor print quality.
· poorly ventilated
Store spare supplies such as drum cartridges and toner cartridges in a dark place without removing from the package before use. If they are exposed to direct sunlight, poor print quality may result. Do not touch the surface (green portion) of the drum cartridge. Doing so will damage the surface of the cartridge, causing poor print quality. · subject to extreme temperature or humidity changes, e.g., near an air conditioner or heater.
1
3. Checking packed components and accessories
Open the carton and check if the following components and accessories are included.
1
The copier should be installed near an accessible power outlet for easy connection. Be sure to connect the power cord only to a power outlet that meets the specified voltage and current requirements. Also make certain the outlet is properly grounded. Be sure to allow the required space around the machine for servicing and proper ventilation.
Start Guide (Leaflet)
Operation Guide (CD)
20cm (8")
20cm (8") 10cm (4")
10cm (4")
MX-B201/B201D UNPACKING AND INSTALLATION 5 - 1
1 '11/Oct/17
4. Unpacking
Be sure to hold the handles on both sides of the unit to unpack the unit and carry it to the installation location.
7) Remove the screw (1 pc). 8) Remove Upper developer unit.
5. Removing protective packing materials
Remove all pieces of tape shown in the illustration below. Then open the SPF and remove protective materials. After that, take out the bag containing the toner cartridge.
9) Shake the aluminum bag to stir developer 10) Supply developer from the aluminum bag to the top of the MX roller evenly.
1
6. Developer unit installation
1) 2) 3) Open the side and front cabinets of the copier. 4) Remove the locking tape of the developer unit. 5) Remove the screw which is fixing the copier and Developer unit. 6) Remove Developer unit slowly from the copier.
Note: Be careful not to spill developer outside Developer unit. 11) Attach Upper developer unit and fix it with a screw. 12) Rotate the MG roller gear to distribute developer evenly.
5 3
1
2
4
Note: Never rotate the gear in the reverse direction.
MX-B201/B201D UNPACKING AND INSTALLATION 5 - 2
Note: When carrying Developer unit, do not tilt it extremely as shown with the arrow in the figure below. (To prevent spilling developer)
4) Insert Toner unit carefully into the copier. 5) Insert until the hook is engaged with the copier as shown in the figure below.
13) Insert Developer unit carefully into the copier. Note: Quick insertion may result in splash of developer. Be sure to insert carefully. 14) Confirm that Developer unit is completely inserted to the bottom of the machine, fix Developer unit and the machine with a screw. 15) Completion of Developer unit installation 6) Pull out the shutter in the arrow direction.
7. Toner cartridge installation
1) To prevent against uneven distribution of toner, hold Toner unit with both hands and shake it several times horizontally.
Note: Do not carry the toner unit by the shutter, it may come off and cause the toner unit to be dropped. 7) Completion of Toner unit installation Close the front and side cabinets. 2) Hold the section of Toner unit shown in the figure below, remove the packing tape, and remove the cushion. 3) Pull out the cushion in the arrow direction.
8. Loading paper
1) Raise the handle of the paper tray and pull the paper tray out until it stops.
2) Remove the pressure plate lock. Rotate the pressure plate lock in the direction of the arrow to remove it while pressing down the pressure plate of the paper tray.
MX-B201/B201D UNPACKING AND INSTALLATION 5 - 3
1 '11/Oct/17
3) Store the pressure plate lock which has been removed in step 2). To store the pressure plate lock, rotate the lock to fix it on the relevant location.
9. Software
The CD-ROM that accompanies the machine contains the following software:
Pressure plate lock
MFP driver
Printer driver The printer driver enables you to use the printer function of the machine.
1
Scanner driver (USB only) 4) Adjust the paper guides on the paper tray to the copy paper width and length. Squeeze the lever of paper guide (A) and slide the guide to match with the width of the paper. Move paper guide (B) to the appropriate slot as marked on the tray. The scanner driver allows you to use the scanning function of the machine with TWAIN-compliant and WIA-compliant applications.
Button Manager
Button Manager allows you to use the scanner menus on the machine to scan a document.
Sharpdesk
Sharpdesk is an integrated software environment that makes it easy to manage documents and image files, and launch applications.
Paper guide (B) Paper guide (A)
5) Fan the paper and insert it into the tray. Make sure the edges go under the corner hooks. Note: Do not load paper above the maximum height line ( Exceeding the line will cause a paper misfeed. ).
A. Before installation
(1) Hardware and software requirements
Check the following hardware and software requirements in order to install the software. Computer type Operating system *2 *3 *4 Display Hard disk free space Other hardware requirements IBM PC/AT or compatible computer equipped with a USB2.0 *1 Windows 2000 Professional, Windows XP, Windows Vista, Windows 7 1024 x 768 dots resolution and 16-bit color or higher is recommended. 150 MB or more An environment on which any of the operating systems listed above can fully operate
6) Gently push the paper tray back into the unit.
*1: Compatible with Windows 2000 Professional, Windows XP Professional/Home Edition, Windows Vista or Windows 7 preinstalled model standardly equipped with a USB port. *2: Printing is not available in MS-DOS mode. *3: The machine does not support printing from a Macintosh environment. *4: Administrator's rights are required to install the software using the installer.
MX-B201/B201D UNPACKING AND INSTALLATION 5 - 4
(2)
Installation environment and usable software
The following table shows the drivers and software that can be installed for each version of Windows and interface connection method. Cable USB Operating System Windows 2000/XP/ Vista/7 MFP Driver Button Sharpdesk* Printer Scanner Manager driver driver Available
7) To install all of the software, click the "Standard" button and go to step 12). To install particular packages, click the "Custom" button and go to next step.
* Sharpdesk can not be used under Windows 2000 environment.
B. Installing the software
Note: · The screen images in this manual are mainly for Windows XP. With other versions of Windows, some screen images may be different from those in this manual. · In the following explanations it is assumed that the mouse is configured for right hand operation. · The scanner feature only works when using a USB cable. · If an error message appears, follow the instructions on the screen to solve the problem. After the problem is solved, the installation procedure will continue. Depending on the problem, you may have to click the "Cancel" button to exit the installer. In this case, reinstall the software from the beginning after solving the problem.
8) Click the "MFP Driver" button. Click the "Display Readme" button to show information on packages that are selected.
(1)
Using the machine with a USB connection
1) The USB cable must not be connected to the machine. Make sure that the cable is not connected before proceeding. If the cable is connected, a Plug and Play window will appear. If this happens, click the "Cancel" button to close the window and disconnect the cable. Note: The cable will be connected in step 13). 2) Insert the CD-ROM into your computer's CD-ROM drive. 3) Click the "start" button, click "My Computer" ( double-click the CD-ROM icon ( ). ), and then
· On Windows Vista/7, click the "Start" button, click "Computer", and then double-click the CD-ROM icon. · On Windows 2000, double-click "My Computer", and then double-click the CD-ROM icon. 4) Double-click the "setup" icon ( ). On Windows Vista/7, if a message screen appears asking you for confirmation, click "Allow". 5) The "SOFTWARE LICENSE" window will appear. Make sure that you understand the contents of the software license, and then click the "Yes" button. Note: You can show the "SOFTWARE LICENSE" in a different language by selecting the desired language from the language menu. To install the software in the selected language, continue the installation with that language selected. 6) Read the "Readme First" in the "Welcome" window and then click the "Next" button.
MX-B201/B201D UNPACKING AND INSTALLATION 5 - 5
9) Select "Connected to this computer" and click the "Next" button. Follow the on-screen instructions.
12) When installing is finished, click the "Close" button. Caution: · If you are using Windows Vista or 7 and a security warning window appears, be sure to click "Install this driver software anyway". · If you are running Windows 2000/XP and a warning message appears regarding the Windows logo test or digital signature, be sure to click "Continue Anyway" or "Yes". A message will appear instructing you to connect the machine to your computer. Click the "OK" button. Note: After the installation, a message prompting you to restart your computer may appear. In this case, click the "Yes" button to restart your computer. 13) Make sure that the power of the machine is turned on, and then connect the USB cable. Windows will detect the machine and a Plug and Play screen will appear.
Caution: · If you are using Windows Vista or 7 and a security warning window appears, be sure to click "Install this driver software anyway". · If you are running Windows 2000/XP and a warning message appears regarding the Windows logo test or digital signature, be sure to click "Continue Anyway" or "Yes". 10) You will return to the window of step 8). If you wish to install Button Manager or Sharpdesk, click the "Utility Software" button. If you do not wish to install the Utility Software, click the "Close" button and go to step 12). Note: After the installation, a message prompting you to restart your computer may appear. In this case, click the "Yes" button to restart your computer. Installing the Utility Software 11) Click the "Button Manager" or the "Sharpdesk" button. Click the "Display Readme" button to show information on packages that are selected. Follow the on-screen instructions.
14) Follow the instructions in the plug and play window to install the driver. Follow the on-screen instructions. Caution: · If you are using Windows Vista or 7 and a security warning window appears, be sure to click "Install this driver software anyway". · If you are running Windows 2000/XP and a warning message appears regarding the Windows logo test or digital signature, be sure to click "Continue Anyway" or "Yes". This completes the installation of the software. · If you installed Button Manager, set up Button Manager as explained in "SETTING UP BUTTON MANAGER". · If you installed Sharpdesk, the Sharpdesk setup screen will appear. Follow the instructions in the screen to set up Sharpdesk.
(2)
Connecting a USB cable
Follow the procedure below to connect the machine to your computer. A USB cable for connecting the machine to your computer is not included with the machine. Please purchase the appropriate cable for your computer. Caution: · USB is available with a PC/AT compatible computer that was originally equipped with USB and had Windows 2000 Professional, Windows XP, Windows Vista or Windows 7 preinstalled. · Do not connect the USB cable before installing the printer driver. The USB cable should be connected during installation of the printer driver. Note: · If the machine will be connected using a USB 2.0 port of your computer, please purchase a USB cable that supports USB 2.0. · Use the machine's "HI-SPEED" mode only when using a computer that is running Windows 2000/XP/Vista or 7. · Even when the Microsoft USB 2.0 driver is used, it may not be possible to obtain full USB 2.0 speed if a PC card supporting USB 2.0 is used. To obtain the latest driver (which may enable a higher speed), contact the manufacturer of your PC card. 1) Insert the cable into the USB connector on the machine.
2) Insert the other end of the cable into your computer's USB port. MX-B201/B201D UNPACKING AND INSTALLATION 5 - 6
(3)
Using the machine as a shared printer
If the machine will be used as a shared printer on a network, follow these steps to install the printer driver in the client computer. Note: To configure the appropriate settings in the print server, see the operation manual or help file of your operating system. 1) Perform steps 2) through 6) in "Installing the software". 2) Click the "Custom" button.
5) Click the "Add Network Port" button. In Windows Vista/7, the "Add Network Port" button does not appear.
6) Select the network printer that is shared and click the "OK" button. Ask your network administrator for the server name and printer name of the machine on the network.
3) Click the "MFP Driver" button. Click the "Display Readme" button to show information on packages that are selected.
7) In the printer port selection window, verify the network printer that is shared and whether the machine is to be used as the default printer, make the selections and click the "Next" button. Follow the on-screen instructions. Caution: · If you are using Windows Vista/7 and a security warning window appears, be sure to click "Install this driver software anyway". · If you are running Windows 2000/XP and a warning message appears regarding the Windows logo test or digital signature, be sure to click "Continue Anyway" or "Yes". 8) You will return to the window of step 3). Click the "Close" button. Note: After the installation, a message prompting you to restart your computer may appear. In this case, click the "Yes" button to restart your computer. This completes the installation of the software.
4) Select "Connected via the network" and click the "Next" button.
MX-B201/B201D UNPACKING AND INSTALLATION 5 - 7
C. Setting up Button Manager
Button Manager is a software program that works with the scanner driver to enable scanning from the machine. To scan using the machine, Button Manager must be linked with the scan menu on the machine. Follow the steps below to link Button Manager to scanner events.
(1)
Windows XP/Vista/7
1) Click the "Start" button, click "Control Panel", click "Printers and Other Hardware", and then click "Scanners and Cameras". · In Windows Vista/7, click the "start" button, select "Control Panel" and click "Printers and Other Hardware", and then click "Scanners and Cameras". 2) Click the "SHARP MX-xxxx" icon and select "Properties" from the "File" menu. · On Windows Vista/7, select "Properties" from the "Organize" menu. 3) In the "Properties" screen, click the "Events" tab. 4) Select "SC1:" from the "Select an event" pull-down menu.
7) Repeat Steps 4) through 6) to link Button Manager to "SC2:" through "SC6:". Select "SC2:" from the "Select an event" pull-down menu. Select "Start this program", select "Sharp Button Manager T" from the pull-down menu, and then click the "Apply" button. Do the same for each ScanMenu through "SC6:". When the settings have been completed, click the "OK" button to close the screen. Button Manager is now linked to the scan menu (1 through 6). The scan settings for each of scan menu 1 through 6 can be changed with the setting window of Button Manager. For the factory default settings of the scan menu and the procedures for configuring Button Manager settings, see "Button Manager Settings" in the Online Manual.
(2)
Windows 2000
1) Click the "Start" button, select "Settings", and then click "Control Panel". 2) Double-click the "Scanners and Cameras" icon. 3) Select "SHARP MX-xxxx" and click the "Properties" button. 4) In the "Properties" screen, click the "Events" tab. 5) Select "SC1:" from the "Scanner events" pull-down menu.
5) Select "Start this program" and then select "Sharp Button Manager Y" from the pull-down menu. 6) Select "Sharp Button Manager Y" in "Send to this application". Note: If other applications are shown, deselect the checkboxes for the other applications and leave only the Button Manager checkbox selected.
6) Click the "Apply" button.
7) Click the "Apply" button. MX-B201/B201D UNPACKING AND INSTALLATION 5 - 8
1 '11/Oct/17
8) Repeat Steps 5) through 7) to link Button Manager to "SC2:" through "SC6:". Select "SC2:" from the "Scanner events" pull-down menu. Select "Sharp Button Manager Y" in "Send to this application" and click the "Apply" button. Do the same for each ScanMenu through "SC6:". When the settings have been completed, click the "OK" button to close the screen. Button Manager is now linked to the scan menu (1 through 6). The scan settings for each of scan menu 1 through 6 can be changed with the setting window of Button Manager. For the factory default settings of the scan menu and the procedures for configuring Button Manager settings, see "Button Manager settings".
11. Moving
Moving instructions
When moving the unit, follow the procedure below. Note: When moving this unit, be sure to remove the toner cartridge and developer unit in advance. 1) Turn the power switch off and remove the power cord from the outlet. 2) Open the side cover and front cover, in that order. Remove the toner cartridge and developer unit and close the front cover and side cover, in that order. To open and close the side cover and front cover, and to remove the toner cartridge and developer unit. 3) Raise the handle of the paper tray and pull the paper tray out until it stops. 4) Push the center of the pressure plate down until it locks in place and lock the plate using the pressure plate lock which has been stored in the front of the paper tray. 5) Push the paper tray back into the unit. 6) Lock the scan head locking switch. Note: When shipping the unit, the scan head locking switch must be locked to prevent shipping damage. 7) Close the multi-bypass tray and the paper output tray extension, and attach the packing materials and tape which were removed during installation of the unit. 8) Pack the unit into the carton.
1 1
1
10. Interface
Connector
Type-B connector
Cable
Shielded twisted pair cable (2 m (6 feet) Max.: high-speed transmission equivalent)
Pin configuration
The pin numbers and signal names are listed in the following table.
2 1
12. Scanner moisture-proof kit
If the machine is installed in a highly humid environment, you can alleviate dew condensation inside the scanner by installing the scanner moisture-proof kit described below.
A. Components
Scanner moisture-proof kit (DKIT-0016QSZZ)
3 4
1 2 3 4 5 6 7
Pin No. 1 2 3 4
Signal name +5V -DATA +DATA GND
Name Scanner condensation prevention mylar Optical right hole mylar B Scanner motor metal plate cushion Scanner upper surface cushion Scanner motor lower mylar Scanner UPG mylar J3 Fan housing cushion
Part code PSHEZ0493QSZZ PSHEZ0469QSZZ PMLT-0106QSZZ PMLT-0105QSZZ PSHEP0600QSZZ PSHEP0599QSZZ PMLT-0108QSZ1
Qty 3 2 2 1 1 1 1
B. Precautions at installation
Clean the position where each cushion/mylar is attached with industrial alcohol before the work.
MX-B201/B201D UNPACKING AND INSTALLATION 5 - 9
C. Attachment method
Turn the main switch to the "OFF" position and remove the power plug from the outlet. 1) Remove original cover.
4) Attach the Scanner condensation prevention mylar at the 3 positions on the rear side of the main unit as described below. Note: The hole should be covered with the mylar. Align the edge of the mylar to the R part (the yellow line in the diagram below) so that the hole of the metal plate is covered as much as possible.
2) Remove the rear cabinet. Remove the three screws and then remove the rear cabinet. Align the edge of the mylar to the R part (the yellow line in the diagram below) so that the hole of the metal plate is covered as much as possible.
3) Remove the rear cover for the document glass. <1> Remove the two screws and then remove the right glass holder. <2> Slide the rear cover for the document glass to remove it. <3> Remove the table glass. Attach along the edge of the projection (the yellow line in the diagram below).
1
3 2
MX-B201/B201D UNPACKING AND INSTALLATION 5 - 10
5) Attach the Optical right hole mylar B at the 2 positions shown in the diagrams below which are at the top of the rear side of the main unit. Note: The holes should be covered with the mylar. Attach along the edge of the cushion (the yellow line in the diagram below). Align with the inside line of the bent part (the yellow line in the diagram below).
7) Attach the Scanner upper surface cushion on the top and the rear side at the rear side of the main unit. Align the cushion with the side of the raised part (the yellow line in the diagram below).
Stick the excessive part on the side.
Align with the raised part (the yellow line in the diagram below). Match the center of the mylar (in the horizontal direction) to the center of the raised part.
Stick the excessive part on the side.
6) Attach the Scanner motor metal plate cushion at 1 position on the attachment plate of the motor on the rear side of the main unit. Note: The hole on the top of the motor unit should be covered with the mylar. Align the edge of the metal plate and the edge of the cushion (the yellow line in the diagram below).
Do not cover this hole.
Align the edge of the cushion with the edge of the metal plate.
Bend the part which is sticking out to the rear side of the scanner and attach to the surface.
Press the cushion at the steps shown in the diagram so that there will be no gap. Press the cushion to make sure all the holes are covered.
20mm - 25mm
Press and attach the cushion aligning it to the metal plate so that there will be no gap between them.
MX-B201/B201D UNPACKING AND INSTALLATION 5 - 11
8) Bend the edge of the Scanner motor lower mylar and stick together.
10) Attach the Scanner motor metal plate cushion covering the bottom part of the Scanner motor lower mylar. Note: The hole under the motor unit should be covered. Attach the cushion to cover the gap between the mylar and the metal plate (the yellow mark).
Stick the lower part of the cushion to the mylar, too.
Stick together.
Stick together.
9) Attach the Scanner motor lower mylar at 1 position under the motor attachment plate on the rear side of the main unit. Note: The mylar should cover the hole under the motor unit. Attach matching the hole (the yellow mark in the diagram) and along with the side edge (the yellow arrow in the diagram). Disconnect the motor harness from the connector and take off the snap band from the hole.
Press the cushion with a sharp-pointed stick or something to fill the gap between the mylar and the metal plate.
11) Attach the motor connector and the snap band to the original position.
12) Attach the Scanner UPG mylar J3 to cover the hole on the right side of inside of the scanner. Note: The mylar should cover the hole shown by the arrow in the diagram. Press the mylar with a sharp-pointed stick or something so that it is stuck correctly. Attach along with the bent part of the metal plate and align the edge of the mylar with the line shown in the diagram (the yellow line in the diagram).
MX-B201/B201D UNPACKING AND INSTALLATION 5 - 12
13) Attach the Fan housing cushion to the cooling fan at the position shown in the diagram below. Cover the top and the right side of the fan housing when you see the fan housing from the backside of the machine. Note: Please make sure the double-sided tape is not exposed where the cushion is sticking out from the edge of the fan housing.
A
View from the arrow A
Back side
Reference position Attach the cushion leaving 3 - 7mm from the edge.
3 - 7mm
Attach the cushion leaving 3 - 7mm from the edge so that the gap between the Fan housing cushion and the filter of the rear cabinet is filled for sure. 14) Attach the parts removed in the items 1), 2), and 3).
MX-B201/B201D UNPACKING AND INSTALLATION 5 - 13
[6] COPY PROCESS
An OPC drum is used for the photoconductor. (Structure of the OPC drum layers) OPC layer (20 microns thick) Pigment layer (0.2 to 0.3 microns thick) Aluminum drum
1. Functional diagram
Main charger Laser beam Cleaning blade
MG roller
Drum
Transfer unit Resist roller
(Basic operation cycle)
Semiconductor laser
Focus correction lens
Main high voltage unit Exposure
Saw tooth
Charge
Toner
Drum Developing
Cleaning
Cleaning blade
Developer
Waste toner box
PS roller
To face down tray
Paper release
Fusing
Separation
Transfer
Synchronization with drum
Manual feed
Heat roller Heater lamp
Electrode
Transfer charger Transfer high voltage unit
Cassette paper feed
Print process
Paper transport route
MX-B201/B201D COPY PROCESS 6 - 1
2. Outline of print process
This printer is a non-impact printer that uses a semiconductor laser and electrostatic print process. This printer uses an OPC (Organic Photo Conductor) for its photoconductive material. First, voltage from the main corona unit charges the drum surface and a latent image is formed on the drum surface using a laser beam. This latent image forms a visible image on the drum surface when toner is applied. The toner image is then transferred onto the print paper by the transfer corona and fused on the print paper in the fusing section with a combination of heat and pressure. Step-1: Charge Step-2: Exposure * Latent image is formed on the drum. Step-3: Developing Latent image formed on the drum is then changed into visible image with toner. Step-4: Transfer The visible image (toner image) on the drum is tr