Text preview for : Voltmčtre.pdf part of MAAS KNT-5000 Stabilized DC Power Supply
MAAS KNT-5000
Back to : Maas KNT-5000.pdf | Home
M
Author:
AN557
MULTIPLEXING FOUR 7-SEGMENT LED DISPLAYS
Hardware
The PIC16C71's I/O ports have an improved sink/source specification. Each I/O pin can sink up to 25 mA and source 20 mA, in addition total PORTB source current is 100 mA and sink current is 150 mA. PORTA is rated for 50 mA source current and 80 mA sink current. This makes the PIC16C71 ideal for driving 7-segment LEDs. Since the total number of I/O pins is limited to 13, the 8-bit PORTB is used to drive the 4 LEDs, while external sink transistors or MOSFETs are used to sink the digit current (Figure 1). Another alternative is to use ULN2003 open collector sink current drivers, which are available in 16-pin DIP or very small SO-16 packages. Each transistor on the ULN2003 can sink a maximum of 500 mA and the base drive can be directly driven from the PORTA pins.
Four Channel Digital Voltmeter with Display and Keyboard
Stan D'Souza Microchip Technology Inc.
INTRODUCTION
The PIC16C71 is a member of the mid-range family of 8-bit, high-speed microcontrollers, namely the PIC16CXXX. The salient features of the PIC16C71 are: · · · · Improved and enhanced instruction set 14-bit instruction word Interrupt capability On-chip four channel, 8-bit A/D converter
This application note demonstrates the capability of the PIC16C71. This application note has been broken down into four subsections: Multiplexing Four 7-Segment LED Displays Multiplexing Four 7-Segment LED Displays and Scanning a 4x4 Keypad Multiplexing Four 7-Segment LED Displays and the A/D Channel0 Multiplexing Four 7-Segment LED Displays with a 4x4 Keypad and 4 A/D Channels
FIGURE 1:
MULTIPLEXING FOUR 7-SEGMENTS LEDS
LED Module
8 x 220 NPN 4.7k NPN 4.7k 17 18 1 2
RA0 RA1 RA2 RA3
NPN 4.7k NPN 4.7k
RB0 RB1 RB2 RB3 RB4 RB5 RB6 RB7
6 7 8 9 10 11 12 13
PIC16C71
© 1997 Microchip Technology Inc.
DS00557C-page 1
AN557
Software
The multiplexing is achieved by turning on each LED for a 5 µs duration every 20 µs. This gives an update rate of 50 Hz, which is quite acceptable to the human eye as a steady display. The 5 µs time-base is generated by dividing the 4.096 MHz oscillator clock. The internal prescaler is configured to be a divide by 32 and assigned to Timer0. TMR0 is pre-loaded with a value = 96. TMR0 will increment to FFh and then roll over to 00h after a period = (256-96)·(32·4/4096000) = 5 µs. When TMR0 rolls over, flag bit T0IF flag is set, and because bits T0IE and GIE are enabled, an interrupt is generated. The software implements a simple timer which increments at a 1 second rate. Every second, the 4 nibble (two 8-bit registers MsdTime and LsdTime) are incremented in a BCD format. The lower 4 bits of LsdTime correspond to the least significant digit (LSD) on the display. The high 4 bits of LsdTime correspond to the second significant digit of the display and so on. Depending on which display is turned on, the corresponding 4-bit BCD value is extracted from either MsdTime or LsdTime, and decoded to a 7-segment display. The TMR0 interrupt is generated at a steady rate of 5 µs and given an instruction time of 1 µs. The entire display update program can reside in the interrupt service routine with no chance of getting an interrupt within an interrupt. The Code Listing for this section is in Appendix A.
MULTIPLEXING FOUR 7-SEGMENT LED DISPLAYS AND SCANNING A 4x4 KEYPAD
Hardware
A 4x4 keypad can be very easily interfaced to the PIC16C71's PORTB (Figure 2). Internal pull-ups on pins RB7:RB4 can be enabled/disabled by clearing/setting bit RBPU (OPTION<7>). The internal pull-ups have a value of 20k at 5V (typical). In order to sense a low level at the input, the switch is "connected" to ground through a 2.2 k resistor. A key hit normally lasts anywhere from 50 ms to as long as a person holds the key down. In order not to miss any key hits, the keypad is sampled every 20 µs (just after the update of the MSD).
Software
To sample the keypad, the digit sinks are first disabled. PORTB is then configured with RB7:RB4 as inputs and RB3:RB0 as outputs driven high. The pull-ups on RB7:RB4 are enabled. Sequentially RB3:RB0 are made low while RB7:RB4 are checked for a key hit (a low level). One key hit per scan is demonstrated in this program. Multiple key hits per scan can very easily be implemented. Once the key hit is sensed, a 40 ms debounce period elapses before key sampling is resumed. No more key hits are sensed until the present key is released. This prevents erroneous key inputs. The program basically inputs the key hit and displays its value as a hexadecimal character on the multiplexed 7- segment LEDs. The Code Listing for this section is in Appendix B.
FIGURE 2:
MULTIPLEXING FOUR 7-SEGMENT LEDS WITH A 4X4 KEYPAD
LED Module 9 10 11 12
4 x 220 NPN 4.7k NPN 4.7k 17 18 1 2
RA0 RA1 RA2 RA3
NPN 4.7k NPN 4.7k
RB0 RB1 RB2 RB3 RB4 RB5 RB6 RB7 PIC16C71
6 7 8 9 10 11 12 13 4 x 220
2.2k
2.2k
2.2k
2.2k
0 4 8 C
1 5 9 D
2 6 A E
3 7 B F
DS00557C-page 2
© 1997 Microchip Technology Inc.
AN557
MULTIPLEXING FOUR 7-SEGMENT LED DISPLAYS AND THE A/D CHANNEL0
Hardware
The four analog channels are connected to RA3:RA0. If any of these pins are used normally as digital I/O, they can momentarily be used as analog inputs. In order to avoid interference from the analog source, it is advisable to buffer the analog input through a voltage follower op-amp, however, it is not always necessary. Figure 3 and Figure 4 show some typical configurations. In this application, the analog input is a potentiometer whose wiper is connected through an RC network to Channel0. The RC is necessary in order to smooth out the analog voltage. The RC does contribute to a delay in the sampling time, however the stability of the analog reading is greatly improved.
Analog input
FIGURE 3:
TYPICAL CONNECTION FOR ANALOG/DIGITAL INPUT
Digital I/O 1k RA0
PIC16C71
FIGURE 4:
TYPICAL CONNECTION FOR ANALOG/DIGITAL INPUT
Digital I/O 1k RA0 10 nF
Software
The analog input is sampled every 20 ms. The digit sinks and the drivers are turned off (i.e., PORTA is configured as an input and PORTB outputs are made low). A 1 ms settling time is allowed for the external RC network connected to the analog input to settle and then the A/D conversion is started. The result is read then converted from an 8-bit binary value to a 3-digit Binary Code Decimal (BCD) value which is then displayed on the 7-segment LEDs. The Code Listing for this section is in Appendix C.
Analog input
PIC16C71
© 1997 Microchip Technology Inc.
DS00557C-page 3
AN557
MULTIPLEXING FOUR 7-SEGMENT LED DISPLAYS WITH A 4x4 KEYPAD AND 4 A/D CHANNELS
Hardware
This section essentially incorporates the previous three sections to give a complete four channel voltmeter. Figure 5 shows a typical configuration. The analog channels are connected through individual potentiometers to their respective analog inputs and are sampled every 20 ms in a round robin fashion. The sampling rate can be increased to as fast as once every 5 µs if required. The keypad sampling need not be any faster than once every 20 µs.
Code Size
Four 7-segment LEDs Program Memory: Data Memory: Four 7-segment LEDs and 4x4 keypad sampling Four 7-segment LEDs and A/D Four 7-segment LEDs, 4x4 keypad sampling, and A/D Program Memory: Data Memory: Program Memory: Data Memory: Program Memory: Data Memory: 139 6 207 13 207 11 207 13
Software
The program samples the analog inputs and saves the result in four consecutive locations starting at "ADVALUE", with Channel0 saved at the first location and so on. KEY 0 ˇ Channel0 or KEY 1 ˇ Channel0 Key hits greater than 3 are ignored. The code listing for this section is in Appendix D.
CONCLUSION
The four A/D channels on the PIC16C71 can be multiplexed with digital I/O, thus reducing overall pin counts and improving I/O pin usage in an analog application.
FIGURE 5:
FOUR CHANNEL VOLTMETER WITH DISPLAY AND KEYPAD
LED Module
9 10 11 12
4 x 220 NPN 4.7k NPN 4.7k 17 18 1 2
RA0 RA1 RA2 RA3
NPN 4.7k NPN 4.7k
RB0 RB1 RB2 RB3 RB4 RB5 RB6 RB7
6 7 8 9 10 11 12 13 4 x 220
PIC16C71
2.2k 2.2k 2.2k 2.2k
0 10 nF 4x1k +5V +5V +5V +5V 8 C 10 nF 10 nF 10 nF 4
1 5 9 D
2 6 A E
3 7 B F
500
500
500
500
DS00557C-page 4
© 1997 Microchip Technology Inc.
AN557
Please check the Microchip BBS for the latest version of the source code. Microchip's Worldwide Web Address: www.microchip.com; Bulletin Board Support: MCHIPBBS using CompuServe® (CompuServe membership not required).
APPENDIX A: MPLX.ASM
MPASM 01.40 Released LOC OBJECT CODE VALUE MPLX.ASM LINE SOURCE TEXT 1-16-1997 16:20:47 PAGE 1
0000000C 0000000D 0000000E 0000000F 00000010 00000011 00000001 00000002 00000026 00000027 0000 0000 2805 0004 0004 281D 0005 0005 2008 0006 2012 0007 0007 2807 0008 0008 0009 000A 000B 000C 000D 000E 000F
1683 3003 0088 0185 0186 1283 0185 0186
00001 00002 00003 00004 00005 00006 00007 00008 00009 00010 00011 00012 00013 00014 00015 00016 00017 00018 00019 00001 00002 00142 00020 00021 00022 00023 00024 00025 00026 00027 00028 00029 00030 00031 00032 00033 00034 00035 00036 00037 00038 00039 00040 00041 00042 00043 00044 00045 00046 00047 00048 00049 00050 00051 00052
;********************************************************************* ;This program demonstrates how to multiplex four 7 segment LED ;digits using a PIC16C71. The four digits will start at 0000 and ;increment at a 1 sec rate up to 9999. ;The LEDs are updated every 5 mS, for a multiplexing rate of 20 mS. ;The TMR0 timer is used in internal interrupt mode to generate the ;5 mS. ; ; Stan D'Souza 5/8/93 ; ; Program: MPLX.ASM ; Revision Date: ; 1-15-97 Compatibility with MPASMWIN 1.40 ; ;********************************************************************** LIST P=16C71 ERRORLEVEL -302 ; include LIST ; P16C71.INC Standard Header File, Version 1.00 Microchip Technology LIST ; TempC equ 0x0c ;temp general purpose regs TempD equ 0x0d TempE equ 0x0e Count equ 0x0f ;count MsdTime equ 0x10 ;most significant Timer LsdTime equ 0x11 ;Least significant Timer OptionReg equ 1 PCL equ 2 BcdMsd equ 26 Bcd equ 27 ; org 0 goto Start ;skip over interrupt vector ; org 4 goto ServiceInterrupts ; Start call InitPorts call InitTimers loop goto loop ; InitPorts bsf STATUS,RP0 ;select Bank1 movlw 3 ;make RA0-3 digital I/O movwf ADCON1 ; / clrf TRISA ;make RA0-4 outputs clrf TRISB ;make RB0-7 outputs bcf STATUS,RP0 ;select Bank0 clrf PORTA ;make all outputs low clrf PORTB ; /
© 1997 Microchip Technology Inc.
DS00557C-page 5
AN557
0010 1585 0011 0008 00053 00054 00055 00056 00057 00058 00059 00060 00061 00062 00063 00064 00065 00066 00067 00068 00069 00070 00071 00072 00073 00074 00075 00076 00077 00078 00079 00080 00081 00082 00083 00084 00085 00086 00087 00088 00089 00090 00091 00092 00093 00094 00095 00096 00097 00098 00099 00100 00101 00102 00103 00104 00105 00106 00107 00108 00109 00110 00111 00112 00113 00114 00115 00116 00117 00118 bsf return PORTA,3 ;enable MSB digit sink ; ; ;The clock speed is 4.096Mhz. Dividing internal clk. by a 32 prescaler, ;the TMR0 will be incremented every 31.25uS. If TMR0 is preloaded ;with 96, it will take (256-96)*31.25uS to overflow i.e. 5mS. So the ;end result is that we get a TMR0 interrupt every 5mS. InitTimers clrf MsdTime ;clr timers clrf LsdTime ; / bsf STATUS,RP0 ;select Bank1 movlw B'10000100' ;assign ps to TMR0 movwf OptionReg ;ps = 32 bcf STATUS,RP0 ;select Bank0 movlw B'00100000' ;enable TMR0 interrupt movwf INTCON ; movlw .96 ;preload TMR0 movwf TMR0 ;start counter retfie ; ServiceInterrupts btfsc INTCON,T0IF ;TMR0 interrupt? goto ServiceTMR0 ;yes then service movlw B'00100000' ;else clr rest movwf INTCON retfie ; ServiceTMR0 movlw .96 ;initialize TMR0 movwf TMR0 bcf INTCON,T0IF ;clr int flag call IncTimer ;inc timer call UpdateDisplay ;update display retfie ; ;The display is incremented every 200*5mS = 1 Sec. IncTimer incf Count,W ;inc count xorlw .200 ;= 200? btfsc STATUS,Z ;no then skip goto DoIncTime ;else inc time incf Count, F return DoIncTime clrf Count ;clr count incf LsdTime,W ;get lsd andlw 0x0F ;mask high nibble xorlw 0x0a ; = 10? btfsc STATUS,Z ;no then skip goto IncSecondLsd ;inc next lsd incf LsdTime, F ;else inc timer return IncSecondLsd swapf LsdTime,W ;get hi in low nibble andlw 0x0F ;mask hi nibble addlw 1 ;inc it movwf LsdTime ;restore back swapf LsdTime, F ; / xorlw 0x0a ; = 10? btfsc STATUS,Z ;no then skip goto IncThirdLsd ;else inc next lsd return IncThirdLsd clrf LsdTime incf MsdTime,W ;get 3rd lsd
0012 0012 0013 0014 0015 0016 0017 0018 0019 001A 001B 001C 001D 001D 001E 001F 0020 0021 0022 0022 0023 0024 0025 0026 0027
0190 0191 1683 3084 0081 1283 3020 008B 3060 0081 0009
190B 2822 3020 008B 0009
3060 0081 110B 2028 2050 0009
0028 0028 0029 002A 002B 002C 002D 002E 002E 002F 0030 0031 0032 0033 0034 0035 0036 0036 0037 0038 0039 003A 003B 003C 003D 003E 003F 003F 0040
0A0F 3AC8 1903 282E 0A8F 0008 018F 0A11 390F 3A0A 1903 2836 0A91 0008 0E11 390F 3E01 0091 0E91 3A0A 1903 283F 0008 0191 0A10
DS00557C-page 6
© 1997 Microchip Technology Inc.
AN557
0041 0042 0043 0044 0045 0046 0047 0047 0048 0049 004A 004B 004C 004D 004E 004F 390F 3A0A 1903 2847 0A90 0008 0E10 390F 3E01 0090 0E90 3A0A 1903 0190 0008 00119 00120 00121 00122 00123 00124 00125 00126 00127 00128 00129 00130 00131 00132 00133 00134 00135 00136 00137 00138 00139 00140 00141 00142 00143 00144 00145 00146 00147 00148 00149 00150 00151 00152 00153 00154 00155 00156 00157 00158 00159 00160 00161 00162 00163 00164 00165 00166 00167 00168 00169 00170 00171 00172 00173 00174 00175 00176 00177 00178 00179 00180 00181 00182 00183 00184 andlw xorlw btfsc goto incf return IncMsd swapf andlw addlw movwf swapf xorlw btfsc clrf return ; ; UpdateDisplay movf clrf andlw movwf bsf rrf btfss bcf btfsc goto btfsc goto btfsc goto UpdateLsd movf andlw goto Update2ndLsd call btfss swapf andlw goto Update3rdLsd call btfss movf andlw goto UpdateMsd swapf andlw btfsc movlw DisplayOut call movwf movf movwf return ; ; LedTable addwf retlw retlw MsdTime,W 0x0F 1 MsdTime MsdTime, F 0x0a STATUS,Z MsdTime ;get hi in lo nibble ;mask hi nibble ;inc timer ;restore back ; / ;= 10? ;no then skip ;clr msd 0x0F 0x0a STATUS,Z IncMsd MsdTime, F ;mask hi nibble ;= 10? ;no then skip ;else Msd ;else inc timer
0050 0050 0051 0052 0053 0054 0055 0056 0057 0058 0059 005A 005B 005C 005D 005E 005E 005F 0060 0061 0061 0062 0063 0064 0065 0066 0066 0067 0068 0069 006A 006B 006B 006C 006D 006E 006F 006F 0070 0071 0072 0073
0805 0185 390F 008C 160C 0C8C 1C03 118C 180C 286B 188C 2866 190C 2861 0811 390F 286F 2080 1D03 0E11 390F 286F 2088 1D03 0810 390F 286F 0E10 390F 1903 300A 2074 0086 080C 0085 0008
PORTA,W PORTA 0x0f TempC TempC,4 TempC, F STATUS,C TempC,3 TempC,0 UpdateMsd TempC,1 Update3rdLsd TempC,2 Update2ndLsd LsdTime,W 0x0f DisplayOut Chk2LsdZero STATUS,Z LsdTime,W 0x0f DisplayOut ChkMsdZero STATUS,Z MsdTime,W 0x0f DisplayOut MsdTime,W 0x0f STATUS,Z 0x0a LedTable PORTB TempC,W PORTA
;present sink value in w ;disable all digits sinks ;save sink value in tempC ;preset for lsd sink ;determine next sink value ;c=1? ;no then reset LSD sink ;else see if Msd ;yes then do Msd ;see if 3rdLsd ;yes then do 3rd Lsd ;see if 2nd Lsd ;yes then do 2nd lsd ;get Lsd in w ; / ;enable display ;msd = 0 & 2 lsd 0? ;yes then skip ;get 2nd Lsd in w ;mask rest ;enable display ;msd = 0? ;yes then skip ;get 3rd Lsd in w ;mask low nibble ;enable display ;get Msd in w ;mask rest ;msd != 0 then skip
;get digit output ;drive leds ;get sink value in w
0074 0074 0782 0075 343F 0076 3406
PCL, F B'00111111' B'00000110'
;add to PC low ;led drive for 0 ;led drive for 1
© 1997 Microchip Technology Inc.
DS00557C-page 7
AN557
0077 0078 0079 007A 007B 007C 007D 007E 007F 345B 344F 3466 346D 347D 3407 347F 3467 3400 00185 00186 00187 00188 00189 00190 00191 00192 00193 00194 00195 00196 00197 00198 00199 00200 00201 00202 00203 00204 00205 00206 00207 00208 00209 00210 00211 00212 00213 retlw retlw retlw retlw retlw retlw retlw retlw retlw ; ; Chk2LsdZero call btfss return swapf andlw btfss return retlw ; ChkMsdZero movf btfss return retlw ; end '-' = Unused) B'01011011' B'01001111' B'01100110' B'01101101' B'01111101' B'00000111' B'01111111' B'01100111' B'00000000' ;led drive ;led drive ;led drive ;led drive ;led drive ;led drive ;led drive ;led drive ;blank led for 2 for 3 for 4 for 5 for 6 for 7 for 8 for 9 drive
0080 0080 0081 0082 0083 0084 0085 0086 0087 0088 0088 0089 008A 008B
2088 1D03 0008 0E11 390F 1D03 0008 340A
ChkMsdZero STATUS,Z LsdTime,W 0x0f STATUS,Z .10
;msd = 0? ;yes then skip ;else return ;get 2nd lsd ;mask of LSD ;0? then skip ;else return with 10
0810 1D03 0008 340A
MsdTime,W STATUS,Z .10
;get Msd in w ;= 0? skip ;else return ;ret with 10
MEMORY USAGE MAP ('X' = Used,
0000 : X---XXXXXXXXXXXX XXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXX 0040 : XXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXX 0080 : XXXXXXXXXXXX---- ---------------- ---------------- ---------------All other memory blocks unused. Program Memory Program Memory Errors : Warnings : Messages : Words Used: Words Free: 0 0 reported, 0 reported, 137 887 0 suppressed 3 suppressed
DS00557C-page 8
© 1997 Microchip Technology Inc.
AN557
Please check the Microchip BBS for the latest version of the source code. Microchip's Worldwide Web Address: www.microchip.com; Bulletin Board Support: MCHIPBBS using CompuServe® (CompuServe membership not required).
APPENDIX B: MPLXKEY.ASM
MPASM 01.40 Released MPLXKEY.ASM 1-16-1997 16:24:40 PAGE 1
LOC OBJECT CODE VALUE
LINE SOURCE TEXT
0000000C 0000000D 0000000E 00000020 00000021 0000000F 00000010 00000011 00000012 00000000 00000001 00000002 00000003 00000013 00000014 0000002F 0000002E 00000001 00000002
00001 00002 00003 00004 00005 00006 00007 00008 00009 00010 00011 00012 00013 00014 00015 00016 00017 00018 00019 00020 00021 00022 00001 00002 00142 00023 00024 00025 00026 00027 00028 00029 00030 00031 00032 00033 00034 00035 00036 00037 00038 00039 00040 00041 00042 00043 00044 00045 00046 00047 00048 00049 00050 00051
;********************************************************************* ;This program is to demonstrate how to multiplex four 7 segment LED ;digits and a 4x4 keypad using a PIC16C71. ;The four digits will start as '0000' and when a key is hit ;it is displayed on the 7 segment leds as a hex value 0 to F. The last ;digit hit is always displayed on the right most led with the rest of ;the digits shifted to the left. The left most digit is deleted. ;The LEDs are updated every 20mS, the keypad is scanned at a rate of 20 ;mS. The TMR0 timer is used in internal interrupt mode to generate the ;5 mS. ; ; Stan D'Souza 5/8/93 ; ; Program: MPLXKEY.ASM ; Revision Date: ; 1-15-97 Compatibility with MPASMWIN 1.40 ; ;********************************************************************** LIST P=16C71 ERRORLEVEL -302 ; include LIST ; P16C71.INC Standard Header File,Ver. 1.00 Microchip Technology, Inc. LIST ; TempC equ 0x0c ;temp general purpose regs TempD equ 0x0d TempE equ 0x0e PABuf equ 0x20 PBBuf equ 0x21 Count equ 0x0f ;count MsdTime equ 0x10 ;most significant Timer LsdTime equ 0x11 ;Least significant Timer KeyFlag equ 0x12 ;flags related to key pad keyhit equ 0 ;bit 0 --> key-press on DebnceOn equ 1 ;bit 1 --> debounce on noentry equ 2 ;no key entry = 0 ServKey equ 3 ;bit 3 --> service key Debnce equ 0x13 ;debounce counter NewKey equ 0x14 WBuffer equ 0x2f StatBuffer equ 0x2e OptionReg equ 1 PCL equ 2 ; ; push macro movwf WBuffer ;save w reg in Buffer swapf WBuffer, F ;swap it swapf STATUS,W ;get status movwf StatBuffer ;save it endm ;
© 1997 Microchip Technology Inc.
DS00557C-page 9
AN557
00052 00053 00054 00055 00056 00057 00058 00059 00060 00061 00062 00063 00064 M M M M 00065 00066 M M M 00067 00068 00069 00070 00071 00072 00073 00074 00075 00076 00077 00078 00079 00080 00081 00082 00083 00084 00085 00086 00087 00088 00089 00090 00091 00092 00093 00094 00095 00096 00097 00098 00099 00100 00101 00102 00103 00104 00105 00106 00107 00108 00109 00110 pop macro swapf movwf swapf endm org goto ; org 4 ;It is always a good practice to save and restore the w reg, ;and the status reg during an interrupt. push movwf WBuffer ;save w reg in Buffer swapf WBuffer, F ;swap it swapf STATUS,W ;get status movwf StatBuffer ;save it call ServiceInterrupts pop swapf StatBuffer,W ;restore status movwf STATUS ; / swapf WBuffer,W ;restore W reg retfie ; Start call InitPorts call InitTimers loop btfsc KeyFlag,ServKey ;key service pending call ServiceKey ;yes then service goto loop ; ;ServiceKey, does the software service for a keyhit. After a key ;service, the ServKey flag is reset, to denote a completed operation. ServiceKey movf NewKey,W ;get key value movwf TempE ;save in TempE swapf MsdTime,W ;move MSD out andlw B'11110000' ;clr lo nibble movwf MsdTime ;save back swapf LsdTime,W ;get Lsd andlw B'00001111' ;mask off lsd iorwf MsdTime, F ;and left shift 3rd swapf LsdTime,W ;get Lsd again andlw B'11110000' ;mask off 2nd iorwf TempE,W ;or with new lsd movwf LsdTime ;make Lsd bcf KeyFlag,ServKey ;reset service flag return ; InitPorts bsf STATUS,RP0 ;select Bank1 movlw 3 ;make RA0-3 digital I/O movwf ADCON1 ; / clrf TRISA ;make RA0-4 outputs clrf TRISB ;make RB0-7 outputs bcf STATUS,RP0 ;select Bank0 clrf PORTA ;make all outputs low clrf PORTB ; / bsf PORTA,3 ;enable MSB digit sink return ; ; ;The clock speed is 4.096Mhz. Dividing internal clk. by a 32 prescaler, ;the TMR0 will be incremented every 31.25uS. If TMR0 is preloaded StatBuffer,W STATUS WBuffer,W ;restore status ; / ;restore W reg
; 0 Start ;skip over interrupt vector
0000 0000 280D 0004
0004 0005 0006 0007 0008 0009 000A 000B 000C 000D 000D 000E 000F 000F 0010 0011
00AF 0EAF 0E03 00AE 2036 0E2E 0083 0E2F 0009
2020 202A 1992 2012 280F
0012 0012 0013 0014 0015 0016 0017 0018 0019 001A 001B 001C 001D 001E 001F
0814 008E 0E10 39F0 0090 0E11 390F 0490 0E11 39F0 040E 0091 1192 0008
0020 0020 0021 0022 0023 0024 0025 0026 0027 0028 0029
1683 3003 0088 0185 0186 1283 0185 0186 1585 0008
DS00557C-page 10
© 1997 Microchip Technology Inc.
AN557
002A 002A 002B 002C 002D 002E 002F 0030 0031 0032 0033 0034 0035 0036 0036 0037 0038 0039 003A 003B 003B 003C 003D 003E 003F 0040 0041 00111 00112 00113 00114 00115 00116 00117 00118 00119 00120 00121 00122 00123 00124 00125 00126 00127 00128 00129 00130 00131 00132 00133 00134 00135 00136 00137 00138 00139 00140 00141 00142 00143 00144 00145 00146 00147 00148 00149 00150 00151 00152 00153 00154 00155 00156 00157 00158 00159 00160 00161 00162 00163 00164 00165 00166 00167 00168 00169 00170 00171 00172 00173 00174 00175 00176 ;with 96, it will take (256-96)*31.25uS to overflow i.e. 5mS. So the ;end result is that we get a TMR0 interrupt every 5mS. InitTimers clrf MsdTime ;clr timers clrf LsdTime ; / clrf KeyFlag ;clr all flags bsf STATUS,RP0 ;select Bank1 movlw B'10000100' ;assign ps to TMR0 movwf OptionReg ;ps = 32 bcf STATUS,RP0 ;select Bank0 movlw B'00100000' ;enable TMR0 interrupt movwf INTCON ; movlw .96 ;preload TMR0 movwf TMR0 ;start counter retfie ; ServiceInterrupts btfsc INTCON,T0IF ;TMR0 interrupt? goto ServiceTMR0 ;yes then service clrf INTCON ;else clr all int bsf INTCON,T0IE return ; ServiceTMR0 movlw .96 ;initialize TMR0 movwf TMR0 bcf INTCON,T0IF ;clr int flag btfsc PORTA,0 ;if msb on then do call ScanKeys ;do a quick key scan call UpdateDisplay ;update display return ; ; ;ScanKeys, scans the 4X4 keypad matrix and returns a key value in ;NewKey (0 - F) if a key is pressed, if not it clears the keyhit flag. ;Debounce for a given keyhit is also taken care of. ;The rate of key scan is 20mS with a 4.096Mhz clock. ScanKeys btfss KeyFlag,DebnceOn ;debounce on? goto Scan1 ;no then scan keypad decfsz Debnce, F ;else dec debounce time return ;not over then return bcf KeyFlag,DebnceOn ;over, clr debounce flag return ;and return Scan1 call SavePorts ;save port values movlw B'11101111' ;init TempD movwf TempD ScanNext movf PORTB,W ;read to init port bcf INTCON,RBIF ;clr flag rrf TempD, F ;get correct column btfss STATUS,C ;if carry set? goto NoKey ;no then end movf TempD,W ;else output movwf PORTB ;low column scan line nop btfss INTCON,RBIF ;flag set? goto ScanNext ;no then next btfsc KeyFlag,keyhit ;last key released? goto SKreturn ;no then exit bsf KeyFlag,keyhit ;set new key hit swapf PORTB,W ;read port movwf TempE ;save in TempE call GetKeyValue ;get key value 0 - F movwf NewKey ;save as New key
0190 0191 0192 1683 3084 0081 1283 3020 008B 3060 0081 0009
190B 283B 018B 168B 0008
3060 0081 110B 1805 2042 20A1 0008
0042 0042 0043 0044 0045 0046 0047 0048 0048 0049 004A 004B 004B 004C 004D 004E 004F 0050 0051 0052 0053 0054 0055 0056 0057 0058 0059 005A 005B
1C92 2848 0B93 0008 1092 0008 208A 30EF 008D 0806 100B 0C8D 1C03 2862 080D 0086 0000 1C0B 284B 1812 2860 1412 0E06 008E 2064 0094
© 1997 Microchip Technology Inc.
DS00557C-page 11
AN557
005C 005D 005E 005F 0060 0060 0061 1592 1492 3004 0093 2097 0008 00177 00178 00179 00180 00181 00182 00183 00184 00185 00186 00187 00188 00189 00190 00191 00192 00193 00194 00195 00196 00197 00198 00199 00200 00201 00202 00203 00204 00205 00206 00207 00208 00209 00210 00211 00212 00213 00214 00215 00216 00217 00218 00219 00220 00221 00222 00223 00224 00225 00226 00227 00228 00229 00230 00231 00232 00233 00234 00235 00236 00237 00238 00239 00240 00241 00242 bsf bsf movlw movwf SKreturn call return ; NoKey bcf goto KeyFlag,keyhit SKreturn ;clr flag RestorePorts ;restore ports KeyFlag,ServKey ;set service flag KeyFlag,DebnceOn ;set flag 4 Debnce ;load debounce time
0062 0062 1012 0063 2860
0064 0064 0065 0066 0067 0068 0069 006A 006B 006C 006D 006E 006E 006F 0070 0071 0072 0073 0074 0074 0075 0075 0076 0077 0077 0078 0078 0079 007A 007B 007C 007D 007E 007F 0080 0081 0082 0083 0084 0085 0086
018C 1D8D 286E 0A8C 1D0D 286E 0A8C 1C8D 286E 0A8C 1C0E 2878 1C8E 2877 1D0E 2875 150C 158C 2878 150C 080C 0782 3400 3401 3402 3403 3404 3405 3406 3407 3408 3409 340A 340B 340C
; ;GetKeyValue gets the key as per ; ; Col1 Col2 ; (RB3) (RB2) ; ;Row1(RB4) 0 1 ; ;Row2(RB5) 4 5 ; ;Row3(RB6) 8 9 ; ;Row4(RB7) C D ; GetKeyValue clrf TempC btfss TempD,3 goto RowValEnd incf TempC, F btfss TempD,2 goto RowValEnd incf TempC, F btfss TempD,1 goto RowValEnd incf TempC, F RowValEnd btfss TempE,0 goto GetValCom btfss TempE,1 goto Get4567 btfss TempE,2 goto Get89ab Getcdef bsf TempC,2 Get89ab bsf TempC,3 goto GetValCom Get4567 bsf TempC,2 GetValCom movf TempC,W addwf PCL, F retlw 0 retlw 1 retlw 2 retlw 3 retlw 4 retlw 5 retlw 6 retlw 7 retlw 8 retlw 9 retlw 0a retlw 0b retlw 0c
the following layout Col3 (RB1) 2 6 A E Col4 (RB0) 3 7 B F
;first column
;second col.
;3rd col. ;last col. ;top ;yes ;2nd ;yes ;3rd ;yes row? then get 0,1,2&3 row? the get 4,5,6&7 row? then get 8,9,a&b
;set msb bits ; / ;do common part
DS00557C-page 12
© 1997 Microchip Technology Inc.
AN557
0087 340D 0088 340E 0089 340F 00243 00244 00245 00246 00247 00248 00249 00250 00251 00252 00253 00254 00255 00256 00257 00258 00259 00260 00261 00262 00263 00264 00265 00266 00267 00268 00269 00270 00271 00272 00273 00274 00275 00276 00277 00278 00279 00280 00281 00282 00283 00284 00285 00286 00287 00288 00289 00290 00291 00292 00293 00294 00295 00296 00297 00298 00299 00300 00301 00302 00303 00304 00305 00306 00307 00308 retlw retlw retlw 0d 0e 0f
008A 008A 008B 008C 008D 008E 008F 0090 0091 0092 0093 0094 0095 0096
0805 00A0 0185 0806 00A1 30FF 0086 1683 1381 30F0 0086 1283 0008
0097 0097 0098 0099 009A 009B 009C 009D 009E 009F 00A0
0821 0086 0820 0085 1683 1781 0185 0186 1283 0008
00A1 00A1 00A2 00A3 00A4 00A5 00A6 00A7 00A8 00A9 00AA 00AB 00AC 00AD 00AE 00AF 00AF 00B0 00B1 00B2 00B2 00B3 00B4 00B5 00B5 00B6 00B7 00B8 00B8 00B9
0805 0185 390F 008C 160C 0C8C 1C03 118C 180C 28B8 188C 28B5 190C 28B2 0811 390F 28BA 0E11 390F 28BA 0810 390F 28BA 0E10 390F
; ;SavePorts, saves the porta and portb condition during a key scan ;operation. SavePorts movf PORTA,W ;Get sink value movwf PABuf ;save in buffer clrf PORTA ;disable all sinks movf PORTB,W ;get port b movwf PBBuf ;save in buffer movlw 0xff ;make all high movwf PORTB ;on port b bsf STATUS,RP0 ;select Bank1 bcf OptionReg,7 ;enable pull ups movlw B'11110000' ;port b hi nibble inputs movwf TRISB ;lo nibble outputs bcf STATUS,RP0 ;Bank0 return ; ;RestorePorts, restores the condition of porta and portb after a ;key scan operation. RestorePorts movf PBBuf,W ;get port b movwf PORTB movf PABuf,W ;get port a value movwf PORTA bsf STATUS,RP0 ;select Bank1 bsf OptionReg,7 ;disable pull ups clrf TRISA ;make port a outputs clrf TRISB ;as well as PORTB bcf STATUS,RP0 ;Bank0 return ; ; UpdateDisplay movf PORTA,W ;present sink value in w clrf PORTA ;disable all digits sinks andlw 0x0f movwf TempC ;save sink value in tempC bsf TempC,4 ;preset for lsd sink rrf TempC, F ;determine next sink value btfss STATUS,C ;c=1? bcf TempC,3 ;no then reset LSD sink btfsc TempC,0 ;else see if Msd goto UpdateMsd ;yes then do Msd btfsc TempC,1 ;see if 3rdLsd goto Update3rdLsd ;yes then do 3rd Lsd btfsc TempC,2 ;see if 2nd Lsd goto Update2ndLsd ;yes then do 2nd lsd UpdateLsd movf LsdTime,W ;get Lsd in w andlw 0x0f ; / goto DisplayOut Update2ndLsd swapf LsdTime,W ;get 2nd Lsd in w andlw 0x0f ;mask rest goto DisplayOut ;enable display Update3rdLsd movf MsdTime,W ;get 3rd Lsd in w andlw 0x0f ;mask low nibble goto DisplayOut ;enable display UpdateMsd swapf MsdTime,W ;get Msd in w andlw 0x0f ;mask rest
© 1997 Microchip Technology Inc.
DS00557C-page 13
AN557
00BA 00BA 00BB 00BC 00BD 00BE 20BF 0086 080C 0085 0008 00309 00310 00311 00312 00313 00314 00315 00316 00317 00318 00319 00320 00321 00322 00323 00324 00325 00326 00327 00328 00329 00330 00331 00332 00333 00334 00335 00336 00337 00338 00339 DisplayOut call movwf movf movwf return ; ; LedTable addwf retlw retlw retlw retlw retlw retlw retlw retlw retlw retlw retlw retlw retlw retlw retlw retlw LedTable PORTB TempC,W PORTA ;get digit output ;drive leds ;get sink value in w
00BF 00BF 00C0 00C1 00C2 00C3 00C4 00C5 00C6 00C7 00C8 00C9 00CA 00CB 00CC 00CD 00CE 00CF
0782 343F 3406 345B 344F 3466 346D 347D 3407 347F 3467 3477 347C 3439 345E 3479 3471
PCL, F B'00111111' B'00000110' B'01011011' B'01001111' B'01100110' B'01101101' B'01111101' B'00000111' B'01111111' B'01100111' B'01110111' B'01111100' B'00111001' B'01011110' B'01111001' B'01110001'
;add ;led ;led ;led ;led ;led ;led ;led ;led ;led ;led ;led ;led ;led ;led ;led ;led ; ;
to PC drive drive drive drive drive drive drive drive drive drive drive drive drive drive drive drive
low for for for for for for for for for for for for for for for for
0 1 2 3 4 5 6 7 8 9 A b C d E F
end '-' = Unused) XXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXX ---------------XXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXX ----------------
MEMORY USAGE MAP ('X' = Used, 0000 0040 0080 00C0 : : : : X---XXXXXXXXXXXX XXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXX ----------------
All other memory blocks unused. Program Memory Words Used: Program Memory Words Free: 205 819
Errors : Warnings : Messages :
0 0 reported, 0 reported,
0 suppressed 6 suppressed
DS00557C-page 14
© 1997 Microchip Technology Inc.
AN557
Please check the Microchip BBS for the latest version of the source code. Microchip's Worldwide Web Address: www.microchip.com; Bulletin Board Support: MCHIPBBS using CompuServe® (CompuServe membership not required).
APPENDIX C: MPLXCH0.ASM
MPASM 01.40 Released MPLXCH0.ASM 1-16-1997 16:24:14 PAGE 1
LOC OBJECT CODE VALUE
LINE SOURCE TEXT
00000026 00000027 0000000C 0000000D 0000000E 00000020 00000021 0000000F 00000010 00000011 00000012 00000005 0000002F 0000002E 00000001 00000002
00001 00002 00003 00004 00005 00006 00007 00008 00009 00010 00011 00012 00013 00014 00015 00016 00017 00018 00019 00020 00021 00001 00002 00142 00022 00023 00024 00025 00026 00027 00028 00029 00030 00031 00032 00033 00034 00035 00036 00037 00038 00039 00040 00041 00042 00043 00044 00045 00046 00047 00048 00049 00050 00051
;********************************************************************* ;This program is to demonstrate how to multiplex four 7 segment LED ;and sample ch0 of the a/d in a PIC16C71. The a/d value is displayed ;as a 3 digit decimal value of the a/d input (0 - 255). ;The LEDs are updated every 20mS, the a/d is sampled every 20 mS. ;The TIMER0 timer is used in internal interrupt mode to generate the ;5 mS. ; ; Stan D'Souza 5/8/93 ; ; ; ; Program: MPLXCH0.ASM ; Revision Date: ; 1-15-97 Compatibility with MPASMWIN 1.40 ; ;********************************************************************** LIST P=16C71 ERRORLEVEL -302 ; include LIST ; P16C71.INC Standard Header File, Ver. 1.00 Microchip Technology, Inc. LIST ; BcdMsd equ 26 Bcd equ 27 TempC equ 0x0c ;temp general purpose regs TempD equ 0x0d TempE equ 0x0e PABuf equ 0x20 PBBuf equ 0x21 Count equ 0x0f ;count MsdTime equ 0x10 ;most significant Timer LsdTime equ 0x11 ;Least significant Timer ADFlag equ 0x12 ;flags related to key pad ADOver equ 5 ;bit 5 --> a/d over WBuffer equ 0x2f StatBuffer equ 0x2e OptionReg equ 1 PCL equ 2 ; push macro movwf WBuffer ;save w reg in Buffer swapf WBuffer, F ;swap it swapf STATUS,W ;get status movwf StatBuffer ;save it endm ; pop macro swapf StatBuffer,W ;restore status movwf STATUS ; / swapf WBuffer,W ;restore W reg endm
© 1997 Microchip Technology Inc.
DS00557C-page 15
AN557
0000 0000 280D 0004 00052 00053 00054 00055 00056 00057 00058 00059 M M M M 00060 00061 M M M 00062 00063 00064 00065 00066 00067 00068 00069 00070 00071 00072 00073 00074 00075 00076 00077 00078 00079 00080 00081 00082 00083 00084 00085 00086 00087 00088 00089 00090 00091 00092 00093 00094 00095 00096 00097 00098 00099 00100 00101 00102 00103 00104 00105 00106 00107 00108 00109 00110 ; org goto ; org 4 ;It is always a good practice to save and restore the w reg, ;and the status reg during an interrupt. push movwf WBuffer ;save w reg in Buffer swapf WBuffer, F ;swap it swapf STATUS,W ;get status movwf StatBuffer ;save it call ServiceInterrupts pop swapf StatBuffer,W ;restore status movwf STATUS ; / swapf WBuffer,W ;restore W reg retfie ; Start call InitPorts call InitTimers call InitAd loop btfsc ADFlag,ADOver ;a/d over? call UpdateAd ;yes then update goto loop ; UpdateAd btfss ADCON0,ADIF ;a/d done? return ;no then leave movf ADRES,W ;get a/d value movwf L_byte clrf H_byte call B2_BCD movf R2,W ;get LSd movwf LsdTime ;save in LSD movf R1,W ;get Msd movwf MsdTime ;save in Msd bcf ADCON0,ADIF ;clr interrupt flag bcf ADCON0,ADON ;turn off a/d bcf ADFlag,ADOver ;clr flag return ; ; ; InitPorts bsf STATUS,RP0 ;select Bank1 movlw 3 ;make RA0-3 digital I/O movwf ADCON1 ; / clrf TRISA ;make RA0-4 outputs clrf TRISB ;make RB0-7 outputs bcf STATUS,RP0 ;select Bank0 clrf PORTA ;make all outputs low clrf PORTB ; / bsf PORTA,3 ;enable MSB digit sink return ; ; ;The clock speed is 4.096Mhz. Dividing internal clk. by a 32 prescaler, ;the TMR0 will be incremented every 31.25uS. If TMR0 is preloaded ;with 96, it will take (256-96)*31.25uS to overflow i.e. 5mS. So the ;end result is that we get a TMR0 interrupt every 5mS. InitTimers clrf MsdTime ;clr timers clrf LsdTime ; / 0 Start ;skip over interrupt vector
0004 0005 0006 0007 0008 0009 000A 000B 000C 000D 000D 000E 000F 0010 0010 0011 0012 0013 0013 0014 0015 0016 0017 0018 0019 001A 001B 001C 001D 001E 001F 0020
00AF 0EAF 0E03 00AE 2039 0E2E 0083 0E2F 0009
2021 202B 2036 1A92 2013 2810
1C88 0008 0809 00A1 01A0 20AD 0824 0091 0823 0090 1088 1008 1292 0008
0021 0021 0022 0023 0024 0025 0026 0027 0028 0029 002A
1683 3003 0088 0185 0186 1283 0185 0186 1585 0008
002B 002B 0190 002C 0191
DS00557C-page 16
© 1997 Microchip Technology Inc.
AN557
002D 002E 002F 0030 0031 0032 0033 0034 0035 1683 3084 0081 1283 3020 008B 3060 0081 0009 00111 00112 00113 00114 00115 00116 00117 00118 00119 00120 00121 00122 00123 00124 00125 00126 00127 00128 00129 00130 00131 00132 00133 00134 00135 00136 00137 00138 00139 00140 00141 00142 00143 00144 00145 00146 00147 00148 00149 00150 00151 00152 00153 00154 00155 00156 00157 00158 00159 00160 00161 00162 00163 00164 00165 00166 00167 00168 00169 00170 00171 00172 00173 00174 00175 00176 bsf movlw movwf bcf movlw movwf movlw movwf retfie ; ; InitAd movlw movwf return B'11000000' ADCON0 ;rc osc, ch 0 for a/d STATUS,RP0 B'10000100' OptionReg STATUS,RP0 B'00100000' INTCON .96 TMR0 ;select Bank1 ;assign ps to TMR0 ;ps = 32 ;select Bank0 ;enable TMR0 interrupt ; ;preload TMR0 ;start counter
0036 0036 30C0 0037 0088 0038 0008
0039 0039 003A 003B 003C 003D 003E 003E 003F 0040 0041 0042 0043 0044
190B 283E 018B 168B 0008
3060 0081 110B 1C05 2045 2071 0008
0045 0045 0046 0047 0047 0048 0049 004A 004B
205A 204C 1908 2847 1692 2067 0008
004C 004C 004D 004E 004F 0050 0051 0052 0053 0054 0055
0186 1683 300F 0085 1283 1408 307D 2056 1508 0008
0056 0056 0057 0057 0058 0059
008C 0B8C 2857 0008
; ; ServiceInterrupts btfsc INTCON,T0IF goto ServiceTMR0 clrf INTCON bsf INTCON,T0IE return ; ServiceTMR0 movlw .96 movwf TMR0 bcf INTCON,T0IF btfss PORTA,0 call SampleAd call UpdateDisplay return ; ; SampleAd call SavePorts call DoAd AdDone btfsc ADCON0,GO goto AdDone bsf ADFlag,ADOver call RestorePorts return ; ; DoAd clrf PORTB bsf STATUS,RP0 movlw 0x0f movwf TRISA bcf STATUS,RP0 bsf ADCON0,ADON movlw .125 call Wait bsf ADCON0,GO return ; ; Wait movwf TempC Next decfsz TempC, F goto Next return ;
;TMR0 interrupt? ;yes then service
;initialize TMR0 ;clr int flag ;last digit? ;then sample a/d ;else update display
;do a ad conversion ;ad done? ;no then loop ;set a/d over flag ;restore ports
;turn off leds ;select Bank1 ;make port a hi-Z ; / ;select Bank0 ;start a/d
;start conversion
;store in temp
© 1997 Microchip Technology Inc.
DS00557C-page 17
AN557
005A 005A 005B 005C 005D 005E 005F 0060 0061 0062 0063 0064 0065 0066 00177 00178 00179 00180 00181 00182 00183 00184 00185 00186 00187 00188 00189 00190 00191 00192 00193 00194 00195 00196 00197 00198 00199 00200 00201 00202 00203 00204 00205 00206 00207 00208 00209 00210 00211 00212 00213 00214 00215 00216 00217 00218 00219 00220 00221 00222 00223 00224 00225 00226 00227 00228 00229 00230 00231 00232 00233 00234 00235 00236 00237 00238 00239 00240 00241 00242 ;SavePorts, saves the porta and portb condition during a key scan ;operation. SavePorts movf PORTA,W ;Get sink value movwf PABuf ;save in buffer clrf PORTA ;disable all sinks movf PORTB,W ;get port b movwf PBBuf ;save in buffer movlw 0xff ;make all high movwf PORTB ;on port b bsf STATUS,RP0 ;select Bank1 bcf OptionReg,7 ;enable pull ups movlw B'11110000' ;port b hi nibble inputs movwf TRISB ;lo nibble outputs bcf STATUS,RP0 ;Bank0 return ; ;RestorePorts, restores the condition of porta and portb after a ;key scan operation. RestorePorts movf PBBuf,W ;get port n movwf PORTB movf PABuf,W ;get port a value movwf PORTA bsf STATUS,RP0 ;select Bank1 bsf OptionReg,7 ;disable pull ups clrf TRISA ;make port a outputs clrf TRISB ;as well as PORTB bcf STATUS,RP0 ;Bank0 return ; ; UpdateDisplay movf PORTA,W ;present sink value in w clrf PORTA ;disable all digits sinks andlw 0x0f movwf TempC ;save sink value in tempC bsf TempC,4 ;preset for lsd sink rrf TempC, F ;determine next sink value btfss STATUS,C ;c=1? bcf TempC,3 ;no then reset LSD sink btfsc TempC,0 ;else see if Msd goto UpdateMsd ;yes then do Msd btfsc TempC,1 ;see if 3rdLsd goto Update3rdLsd ;yes then do 3rd Lsd btfsc TempC,2 ;see if 2nd Lsd goto Update2ndLsd ;yes then do 2nd lsd UpdateLsd movf LsdTime,W ;get Lsd in w andlw 0x0f ; / goto DisplayOut ;enable display Update2ndLsd call Chk2LsdZero ;msd = 0 & 2 lsd 0? btfss STATUS,Z ;yes then skip swapf LsdTime,W ;get 2nd Lsd in w andlw 0x0f ;mask rest goto DisplayOut ;enable display Update3rdLsd call ChkMsdZero ;msd = 0? btfss STATUS,Z ;yes then skip movf MsdTime,W ;get 3rd Lsd in w andlw 0x0f ;mask low nibble goto DisplayOut ;enable display UpdateMsd swapf MsdTime,W ;get Msd in w andlw 0x0f ;mask rest
0805 00A0 0185 0806 00A1 30FF 0086 1683 1381 30F0 0086 1283 0008
0067 0067 0068 0069 006A 006B 006C 006D 006E 006F 0070
0821 0086 0820 0085 1683 1781 0185 0186 1283 0008
0071 0071 0072 0073 0074 0075 0076 0077 0078 0079 007A 007B 007C 007D 007E 007F 007F 0080 0081 0082 0082 0083 0084 0085 0086 0087 0087 0088 0089 008A 008B 008C 008C 008D
0805 0185 390F 008C 160C 0C8C 1C03 118C 180C 288C 188C 2887 190C 2882 0811 390F 2890 20A1 1D03 0E11 390F 2890 20A9 1D03 0810 390F 2890 0E10 390F
DS00557C-page 18
© 1997 Microchip Technology Inc.
AN557
008E 008F 0090 0090 0091 0092 0093 0094 1903 300A 2095 0086 080C 0085 0008 00243 00244 00245 00246 00247 00248 00249 00250 00251 00252 00253 00254 00255 00256 00257 00258 00259 00260 00261 00262 00263 00264 00265 00266 00267 00268 00269 00270 00271 00272 00273 00274 00275 00276 00277 00278 00279 00280 00281 00282 00283 00284 00285 00286 00287 00288 00289 00290 00291 00292 00293 00294 00295 00296 00297 00298 00299 00300 00301 00302 00303 00304 00305 00306 00307 00308 btfsc movlw DisplayOut call movwf movf movwf return ; ; LedTable addwf retlw retlw retlw retlw retlw retlw retlw retlw retlw retlw retlw ; ; Chk2LsdZero call btfss return swapf andlw btfss return retlw ; ChkMsdZero movf btfss return retlw ; ; ; count equ temp equ ; H_byte equ L_byte equ R0 equ R1 equ R2 equ ; ; B2_BCD bcf movlw movwf clrf clrf clrf loop16 rlf rlf rlf rlf rlf ; decfsz STATUS,Z 0x0a LedTable PORTB TempC,W PORTA ;msd != 0 then skip
;get digit output ;drive leds ;get sink value in w
0095 0095 0096 0097 0098 0099 009A 009B 009C 009D 009E 009F 00A0
0782 343F 3406 345B 344F 3466 346D 347D 3407 347F 3467 3400
PCL, F B'00111111' B'00000110' B'01011011' B'01001111' B'01100110' B'01101101' B'01111101' B'00000111' B'01111111' B'01100111' B'00000000'
;add to PC ;led drive ;led drive ;led drive ;led drive ;led drive ;led drive ;led drive ;led drive ;led drive ;led drive ;blank led
low for 0 for 1 for 2 for 3 for 4 for 5 for 6 for 7 for 8 for 9 drive
00A1 00A1 00A2 00A3 00A4 00A5 00A6 00A7 00A8 00A9 00A9 00AA 00AB 00AC
20A9 1D03 0008 0E11 390F 1D03 0008 340A
ChkMsdZero STATUS,Z LsdTime,W 0x0f STATUS,Z .10
;msd = 0? ;yes then skip ;else return ;get 2nd lsd ;mask of LSD ;0? then skip ;else return with 10
0810 1D03 0008 340A
MsdTime,W STATUS,Z .10
;get Msd in w ;= 0? skip ;else return ;ret with 10
00000026 00000027 00000020 00000021 00000022 00000023 00000024
26 27 20 21 22 23 24
; RAM Assignments
00AD 00AE 00AF 00B0 00B1 00B2 00B3 00B4 00B5 00B6 00B7
1003 3010 00A6 01A2 01A3 01A4 0DA1 0DA0 0DA4 0DA3 0DA2
STATUS,0 .16 count R0 R1 R2 L_byte, F H_byte, F R2, F R1, F R0, F count, F
; clear the carry bit
00B8 0BA6
© 1997 Microchip Technology Inc.
DS00557C-page 19
AN557
00B9 28BB 00BA 3400 00BB 3024 00BC 0084 00BD 20C5 00BE 3023 00BF 0084 00C0 20C5 00C1 3022 00C2 0084 00C3 20C5 00C4 28B3 00C5 00C6 00C7 00C8 00C9 00CA 00CB 00CC 00CD 00CE 00CF 3003 0700 00A7 19A7 0080 3030 0700 00A7 1BA7 0080 3400 00309 00310 00311 00312 00313 00314 00315 00316 00317 00318 00319 00320 00321 00322 00323 00324 00325 00326 00327 00328 00329 00330 00331 00332 00333 00334 00335 00336 00337 00338 00339 00340 goto RETLW ; adjDEC movlw movwf call movlw movwf call ; movlw movwf call ; goto ; adjBCD movlw addwf movwf btfsc movwf movlw addwf movwf btfsc movwf RETLW loop16 3 0,W temp temp,3 0 30 0,W temp temp,7 0 0 R0 FSR adjBCD adjDEC 0 R2 FSR adjBCD R1 FSR adjBCD
;
; test if result > 7
; test if result > 7 ; save as MSD
; ; end '-' = Unused) XXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXX ---------------XXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXX ----------------
MEMORY USAGE MAP ('X' = Used, 0000 0040 0080 00C0 : : : : X---XXXXXXXXXXXX XXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXX ----------------
All other memory blocks unused. Program Memory Words Used: Program Memory Words Free: 205 819
Errors : Warnings : Messages :
0 0 reported, 0 reported,
0 suppressed 7 suppressed
DS00557C-page 20
© 1997 Microchip Technology Inc.
AN557
Please check the Microchip BBS for the latest version of the source code. Microchip's Worldwide Web Address: www.microchip.com; Bulletin Board Support: MCHIPBBS using CompuServe® (CompuServe membership not required).
APPENDIX D: MPLXAD.ASM
MPASM 01.40 Released MPLXAD.ASM 1-16-1997 16:23:40 PAGE 1
LOC OBJECT CODE VALUE
LINE SOURCE TEXT
0000000C 0000000D 0000000E 00000020 00000021 0000000F 00000010 00000011 00000012
00000013 00000014 00000015 00000016
00001 00002 00003 00004 00005 00006 00007 00008 00009 00010 00011 00012 00013 00014 00015 00016 00017 00018 00019 00020 00021 00022 00023 00024 00025 00026 00027 00001 00002 00142 00028 00029 00030 00031 00032 00033 00034 00035 00036 00037 00038 00039 00040 00041 00042 00043 00044 00045 00046 00047 00048 00049 00050 00051
;********************************************************************* ;This program demonstrates how to multiplex four 7 segment LED ;digits and a 4X4 keypad along with 4 A/D inputs using a PIC16C71. ;The four digits will first display the decimal a/d value of ch0. ;When keys from 0 - 3 are hit the corresponding channel's a/d value ;is displayed in decimal. ;The LEDs are updated every 20mS, the keypad is scanned at a rate of 20 ;mS. All 4 channels are scanned at 20mS rate, so each channel gets ;scanned every 80mS. A faster rate of scanning is possible as required ;by the users application. ;Timer0 is used in internal interrupt mode to generate the ;5 mS. ; ; Stan D'Souza 5/8/93 ; ;Corrected error in display routine. ; Stan D'Souza 2/27/94 ; ; Program: MPLXAD.ASM ; Revision Date: ; 1-15-97 Compatibility with MPASMWIN 1.40 ; ;********************************************************************** LIST P=16C71 ERRORLEVEL -302 ; include LIST ; P16C71.INC Standard Header File, Ver. 1.00 Microchip Technology, Inc. LIST ; TempC equ 0x0c ;temp general purpose regs TempD equ 0x0d TempE equ 0x0e PABuf equ 0x20 PBBuf equ 0x21 Count equ 0x0f ;count MsdTime equ 0x10 ;most significant Timer LsdTime equ 0x11 ;Least significant Timer ; Flag equ 0x12 ;general purpose flag reg #define keyhit Flag,0 ;bit 0 --> key-press on #define DebnceOn Flag,1 ;bit 1 -> debounce on #define noentry Flag,2 ;no key entry = 0 #define ServKey Flag,3 ;bit 3 --> service key #define ADOver Flag,4 ;bit 4 --> a/d conv. over ; Debnce equ 0x13 ;debounce counter NewKey equ 0x14 DisplayCh equ 0x15 ;channel to be displayed ; ADTABLE equ 0x16 ;4 locations are reserved here ;from 0x16 to 0x19 ;
© 1997 Microchip Technology Inc.
DS00557C-page 21
AN557
0000002F 0000002E 00000001 00000002 00052 00053 00054 00055 00056 00057 00058 00059 00060 00061 00062 00063 00064 00065 00066 00067 00068 00069 00070 00071 00072 00073 00074 00075 00076 00077 M M M M 00078 00079 M M M 00080 00081 00082 00083 00084 00085 00086 00087 00088 00089 00090 00091 00092 00093 00094 00095 00096 00097 00098 00099 00100 00101 00102 00103 00104 00105 00106 00107 00108 00109 00110 WBuffer equ 0x2f StatBuffer equ 0x2e OptionReg equ 1 PCL equ 2 ; ; push macro movwf WBuffer ;save w reg in Buffer swapf WBuffer, F ;swap it swapf STATUS,W ;get status movwf StatBuffer ;save it endm ; pop macro swapf StatBuffer,W ;restore status movwf STATUS ; / swapf WBuffer,W ;restore W reg endm ; org 0 goto Start ;skip over interrupt vector ; org 4 ;It is always a good practice to save and restore the w reg, ;and the status reg during a interrupt. push movwf WBuffer ;save w reg in Buffer swapf WBuffer, F ;swap it swapf STATUS,W ;get status movwf StatBuffer ;save it call ServiceInterrupts pop swapf StatBuffer,W ;restore status movwf STATUS ; / swapf WBuffer,W ;restore W reg retfie ; Start call InitPorts call InitAd call InitTimers loop btfsc ServKey ;key service pending call ServiceKey ;yes then service btfsc ADOver ;a/d pending? call ServiceAD ;yes the service a/d goto loop ; ;ServiceKey, does the software service for a keyhit. After a key ;service, the ServKey flag is reset, to denote a completed operation. ServiceKey bcf ServKey ;reset service flag movf NewKey,W ;get key value sublw 3 ;key > 3? btfss STATUS,C ;no then skip return ;else ignore key movf NewKey,W movwf DisplayCh ;load new channel ; LoadAD movlw ADTABLE ;get top of table addwf DisplayCh,W ;add offset movwf FSR ;init FSR movf 0,W ;get a/d value movwf L_byte clrf H_byte
0000 0000 280D 0004
0004 0005 0006 0007 0008 0009 000A 000B 000C 000D 000D 000E 000F 0010 0010 0011 0012 0013 0014
00AF 0EAF 0E03 00AE 2052 0E2E 0083 0E2F 0009
203B 20EE 2045 1992 2015 1A12 2028 2810
0015 0015 0016 0017 0018 0019 001A 001B 001C 001C 001D 001E 001F 0020 0021
1192 0814 3C03 1C03 0008 0814 0095
3016 0715 0084 0800 00A1 01A0
DS00557C-page 22
© 1997 Microchip Technology Inc.
AN557
0022 0023 0024 0025 0026 0027 2106 0824 0091 0823 0090 0008 00111 00112 00113 00114 00115 00116 00117 00118 00119 00120 00121 00122 00123 00124 00125 00126 00127 00128 00129 00130 00131 00132 00133 00134 00135 00136 00137 00138 00139 00140 00141 00142 00143 00144 00145 00146 00147 00148 00149 00150 00151 00152 00153 00154 00155 00156 00157 00158 00159 00160 00161 00162 00163 00164 00165 00166 00167 00168 00169 00170 00171 00172 00173 00174 00175 00176 call movf movwf movf movwf return B2_BCD R2,W LsdTime R1,W MsdTime ;get LSd ;save in LSD ;get Msd ;save in Msd
0028 0028 0029 002A 002B 002C 002D 002E 002F 0030 0031 0032 0033 0034 0035 0036 0037 0038 0039 003A
0808 008C 3008 0708 1A88 30C1 0088 3016 0084 0C8C 0C8C 0C0C 3903 0784 0809 0080 1212 201C 0008
; ;This routine essentially loads the ADRES value in the table location ;determined by the channel offset. If channel 0 then ADRES is saved ;in location ADTABLE. If channel 1 then ADRES is saved at ADTABLE + 1. ;and so on. ServiceAD movf ADCON0,W ;get adcon0 movwf TempC ;save in temp movlw B'00001000' ;select next channel addwf ADCON0,W ; / btfsc ADCON0,5 ;if <= ch3 movlw B'11000001' ;select ch0 movwf ADCON0 ;now load adres in the table movlw ADTABLE movwf FSR ;load FSR with top rrf TempC, F rrf TempC, F rrf TempC,W ;get in w reg andlw 3 ;mask off all but last 2 addwf FSR, F ;add offset to table movf ADRES,W ;get a/d value movwf 0 ;load indirectly bcf ADOver ;clear flag call LoadAD ;load a/d value in display reg. return
003B 003B 003C 003D 003E 003F 0040 0041 0042 0043 0044
1683 3003 0088 0185 0186 1283 0185 0186 1585 0008
0045 0045 0046 0047 0048 0049 004A 004B 004C 004D 004E 004F 0050
0190 0191 0195 0192 1683 3084 0081 1283 3020 008B 3060 0081
; InitPorts bsf STATUS,RP0 ;select Bank1 movlw 3 ;make RA0-3 digital I/O movwf ADCON1 ; / clrf TRISA ;make RA0-4 outputs clrf TRISB ;make RB0-7 outputs bcf STATUS,RP0 ;select Bank0 clrf PORTA ;make all outputs low clrf PORTB ; / bsf PORTA,3 ;enable MSB digit sink return ; ; ;The clock speed is 4.096Mhz. Dividing internal clk. by a 32 prescaler, ;the TMR0 will be incremented every 31.25uS. If TMR0 is preloaded ;with 96, it will take (256-96)*31.25uS to overflow i.e. 5mS. So the ;end result is that we get a TMR0 interrupt every 5mS. InitTimers clrf MsdTime ;clr timers clrf LsdTime ; / clrf DisplayCh ;show channel 0 clrf Flag ;clr all flags bsf STATUS,RP0 ;select Bank1 movlw B'10000100' ;assign ps to TMR0 movwf OptionReg ;ps = 32 bcf STATUS,RP0 ;select Bank0 movlw B'00100000' ;enable TMR0 interrupt movwf INTCON ; movlw .96 ;preload TMR0 movwf TMR0 ;start counter
© 1997 Microchip Technology Inc.
DS00557C-page 23
AN557
0051 0009 0052 0052 0053 0054 0055 0056 0057 0057 0058 0059 005A 005B 005C 005D 005E 005F 00177 00178 00179 00180 00181 00182 00183 00184 00185 00186 00187 00188 00189 00190 00191 00192 00193 00194 00195 00196 00197 00198 00199 00200 00201 00202 00203 00204 00205 00206 00207 00208 00209 00210 00211 00212 00213 00214 00215 00216 00217 00218 00219 00220 00221 00222 00223 00224 00225 00226 00227 00228 00229 00230 00231 00232 00233 00234 00235 00236 00237 00238 00239 00240 00241 00242 retfie ; ServiceInterrupts btfsc INTCON,T0IF ;TMR0 interrupt? goto ServiceTMR0 ;yes then service clrf INTCON ;else clr all int bsf INTCON,T0IE return ; ServiceTMR0 movlw .96 ;initialize TMR0 movwf TMR0 bcf INTCON,T0IF ;clr int flag btfsc PORTA,0 ;scan keys every 20 mS call ScanKeys ;when digit 1 is on btfsc PORTA,3 ;scan a/d every 20mS call SampleAd ;when digit 4 is on call UpdateDisplay ;update display return ; ; ;ScanKeys, scans the 4x4 keypad matrix and returns a key value in ;NewKey (0 - F) if a key is pressed, if not it clears the keyhit flag. ;Debounce for a given keyhit is also taken care of. ;The rate of key scan is 20mS with a 4.096Mhz clock. ScanKeys btfss DebnceOn ;debounce on? goto Scan1 ;no then scan keypad decfsz Debnce, F ;else dec debounce time return ;not over then return bcf DebnceOn ;over, clr debounce flag return ;and return Scan1 call SavePorts ;save port values movlw B'11101111' ;init TempD movwf TempD ScanNext movf PORTB,W ;read to init port bcf INTCON,RBIF ;clr flag rrf TempD, F ;get correct column btfss STATUS,C ;if carry set? goto NoKey ;no then end movf TempD,W ;else output movwf PORTB ;low column scan line nop btfss INTCON,RBIF ;flag set? goto ScanNext ;no then next btfsc keyhit ;last key released? goto SKreturn ;no then exit bsf keyhit ;set new key hit swapf PORTB,W ;read port movwf TempE ;save in TempE call GetKeyValue ;get key value 0 - F movwf NewKey ;save as New key bsf ServKey ;set service flag bsf DebnceOn ;set flag movlw 4 movwf Debnce ;load debounce time SKreturn call RestorePorts ;restore ports return ; NoKey bcf keyhit ;clr flag goto SKreturn ;
190B 2857 018B 168B 0008
3060 0081 110B 1805 2060 1985 20F1 20BF 0008
0060 0060 0061 0062 0063 0064 0065 0066 0066 0067 0068 0069 0069 006A 006B 006C 006D 006E 006F 0070 0071 0072 0073 0074 0075 0076 0077 0078 0079 007A 007B 007C 007D 007E 007E 007F
1C92 2866 0B93 0008 1092 0008 20A8 30EF 008D 0806 100B 0C8D 1C03 2880 080D 0086 0000 1C0B 2869 1812 287E 1412 0E06 008E 2082 0094 1592 1492 3004 0093 20B5 0008
0080 0080 1012 0081 287E
DS00557C-page 24
© 1997 Microchip Technology Inc.
AN557
00243 00244 00245 00246 00247 00248 00249 00250 00251 00252 00253 00254 00255 00256 00257 00258 00259 00260 00261 00262 00263 00264 00265 00266 00267 00268 00269 00270 00271 00272 00273 00274 00275 00276 00277 00278 00279 00280 00281 00282 00283 00284 00285 00286 00287 00288 00289 00290 00291 00292 00293 00294 00295 00296 00297 00298 00299 00300 00301 00302 00303 00304 00305 00306 00307 00308 ;GetKeyValue gets the key as per the following layout ; ; Col1 Col2 Col3 Col4 ; (RB3) (RB2) (RB1) (RB0) ; ;Row1(RB4) 0 1 2 3 ; ;Row2(RB5) 4 5 6 7 ; ;Row3(RB6) 8 9 A B ; ;Row4(RB7) C D E F ; GetKeyValue clrf TempC btfss TempD,3 ;first column goto RowValEnd incf TempC, F btfss TempD,2 ;second col. goto RowValEnd incf TempC, F btfss TempD,1 ;3rd col. goto RowValEnd incf TempC, F ;last col. RowValEnd btfss TempE,0 ;top row? goto GetValCom ;yes then get 0,1,2&3 btfss TempE,1 ;2nd row? goto Get4567 ;yes the get 4,5,6&7 btfss TempE,2 ;3rd row? goto Get89ab ;yes then get 8,9,a&b Getcdef bsf TempC,2 ;set msb bits Get89ab bsf TempC,3 ; / goto GetValCom ;do common part Get4567 bsf TempC,2 GetValCom movf TempC,W addwf PCL, F retlw 0 retlw 1 retlw 2 retlw 3 retlw 4 retlw 5 retlw 6 retlw 7 retlw 8 retlw 9 retlw 0a retlw 0b retlw 0c retlw 0d retlw 0e retlw 0f ; ;SavePorts, saves the porta and portb condition during a key scan ;operation. SavePorts movf PORTA,W ;Get sink value movwf PABuf ;save in buffer clrf PORTA ;disable all sinks movf PORTB,W ;get port b movwf PBBuf ;save in buffer
0082 0082 0083 0084 0085 0086 0087 0088 0089 008A 008B 008C 008C 008D 008E 008F 0090 0091 0092 0092 0093 0093 0094 0095 0095 0096 0096 0097 0098 0099 009A 009B 009C 009D 009E 009F 00A0 00A1 00A2 00A3 00A4 00A5 00A6 00A7
018C 1D8D 288C 0A8C 1D0D 288C 0A8C 1C8D 288C 0A8C 1C0E 2896 1C8E 2895 1D0E 2893 150C 158C 2896 150C 080C 0782 3400 3401 3402 3403 3404 3405 3406 3407 3408 3409 340A 340B 340C 340D 340E 340F
00A8 00A8 00A9 00AA 00AB 00AC
0805 00A0 0185 0806 00A1
© 1997 Microchip Technology Inc.
DS00557C-page 25
AN557
00AD 00AE 00AF 00B0 00B1 00B2 00B3 00B4 30FF 0086 1683 1381 30F0 0086 1283 0008 00309 00310 00311 00312 00313 00314 00315 00316 00317 00318 00319 00320 00321 00322 00323 00324 00325 00326 00327 00328 00329 00330 00331 00332 00333 00334 00335 00336 00337 00338 00339 00340 00341 00342 00343 00344 00345 00346 00347 00348 00349 00350 00351 00352 00353 00354 00355 00356 00357 00358 00359 00360 00361 00362 00363 00364 00365 00366 00367 00368 00369 00370 00371 00372 00373 00374 movlw movwf bsf bcf movlw movwf bcf return 0xff PORTB STATUS,RP0 OptionReg,7 B'11110000' TRISB STATUS,RP0 ;make all high ;on port b ;select Bank1 ;enable pull ups ;port b hi nibble inputs ;lo nibble outputs ;Bank0
00B5 00B5 00B6 00B7 00B8 00B9 00BA 00BB 00BC 00BD 00BE
0821 0086 0820 0085 1683 1781 0185 0186 1283 0008
00BF 00BF 00C0 00C1 00C2 00C3 00C4 00C5 00C6 00C7 00C8 00C9 00CA 00CB 00CC 00CD 00CD 00CE 00CF 00D0 00D0 00D1 00D2 00D3 00D3 00D4 00D5 00D6 00D6 00D7 00D8 00D8 00D9 00DA 00DB 00DC
0805 0185 390F 008C 160C 0C8C 1C03 118C 180C 28D6 188C 28D3 190C 28D0 0811 390F 28D8 0E11 390F 28D8 0810 390F 28D8 0E10 390F 20DD 0086 080C 0085 0008
00DD 00DD 0782 00DE 343F 00DF 3406
; ;RestorePorts, restores the condition of porta and portb after a ;key scan operation. RestorePorts movf PBBuf,W ;get port b movwf PORTB movf PABuf,W ;get port a value movwf PORTA bsf STATUS,RP0 ;select Bank1 bsf OptionReg,7 ;disable pull ups clrf TRISA ;make port a outputs clrf TRISB ;as well as PORTB bcf STATUS,RP0 ;Bank0 return ; ; UpdateDisplay movf PORTA,W ;present sink value in w clrf PORTA ;disable all digits sinks andlw 0x0f movwf TempC ;save sink value in tempC bsf TempC,4 ;preset for lsd sink rrf TempC, F ;determine next sink value btfss STATUS,C ;c=1? bcf TempC,3 ;no then reset LSD sink btfsc TempC,0 ;else see if Msd goto UpdateMsd ;yes then do Msd btfsc TempC,1 ;see if 3rdLsd goto Update3rdLsd ;yes then do 3rd Lsd btfsc TempC,2 ;see if 2nd Lsd goto Update2ndLsd ;yes then do 2nd lsd UpdateLsd movf LsdTime,W ;get Lsd in w andlw 0x0f ; / goto DisplayOut Update2ndLsd swapf LsdTime,W ;get 2nd Lsd in w andlw 0x0f ;mask rest goto DisplayOut ;enable display Update3rdLsd movf MsdTime,W ;get 3rd Lsd in w andlw 0x0f ;mask low nibble goto DisplayOut ;enable display UpdateMsd swapf MsdTime,W ;get Msd in w andlw 0x0f ;mask rest DisplayOut call LedTable ;get digit output movwf PORTB ;drive leds movf TempC,W ;get sink value in w movwf PORTA return ; ; LedTable addwf PCL, F ;add to PC low retlw B'00111111' ;led drive for 0 retlw B'00000110' ;led drive for 1
DS00557C-page 26
© 1997 Microchip Technology Inc.
AN557
00E0 00E1 00E2 00E3 00E4 00E5 00E6 00E7 00E8 00E9 00EA 00EB 00EC 00ED 345B 344F 3466 346D 347D 3407 347F 3467 3477 347C 3439 345E 3479 3471 00375 00376 00377 00378 00379 00380 00381 00382 00383 00384 00385 00386 00387 00388 00389 00390 00391 00392 00393 00394 00395 00396 00397 00398 00399 00400 00401 00402 00403 00404 00405 00406 00407 00408 00409 00410 00411 00412 00413 00414 00415 00416 00417 00418 00419 00420 00421 00422 00423 00424 00425 00426 00427 00428 00429 00430 00431 00432 00433 00434 00435 00436 00437 00438 00439 00440 retlw retlw retlw retlw retlw retlw retlw retlw retlw retlw retlw retlw retlw retlw ; ; InitAd movlw B'11000000' ;internal rc for tad movwf ADCON0 ; / ;note that adcon1 is set in InitPorts return ; SampleAd call call AdDone btfsc goto bsf call return ; ; DoAd clrf bsf movlw movwf bcf bsf movlw call bsf return ; ; Wait movwf Next decfsz goto return ; ; count equ temp equ ; H_byte equ L_byte equ R0 equ R1 equ R2 equ ; ; TempC, F Next TempC ;store in temp PORTB STATUS,RP0 0x0f TRISA STATUS,RP0 ADCON0,ADON .125 Wait ADCON0,GO ;turn off leds ;select Bank1 ;make port a hi-Z ; / ;select Bank0 ;start a/d ADCON0,GO AdDone ADOver RestorePorts ;ad done? ;no then loop ;set a/d over flag ;restore ports SavePorts DoAd ;do a ad conversion B'01011011' B'01001111' B'01100110' B'01101101' B'01111101' B'00000111' B'01111111' B'01100111' B'01110111' B'01111100' B'00111001' B'01011110' B'01111001' B'01110001' ;led ;led ;led ;led ;led ;led ;led ;led ;led ;led ;led ;led ;led ;led drive drive drive drive drive drive drive drive drive drive drive drive drive drive for for for for for for for for for for for for for for 2 3 4 5 6 7 8 9 A b C d E F
00EE 00EE 30C0 00EF 0088 00F0 0008 00F1 00F1 00F2 00F3 00F3 00F4 00F5 00F6 00F7
20A8 20F8 1908 28F3 1612 20B5 0008
00F8 00F8 00F9 00FA 00FB 00FC 00FD 00FE 00FF 0100 0101
0186 1683 300F 0085 1283 1408 307D 2102 1508 0008
;start conversion
0102 0102 0103 0103 0104 0105
008C 0B8C 2903 0008
00000026 00000027 00000020 00000021 00000022 00000023 00000024
26 27 20 21 22 23 24
; RAM Assignments
© 1997 Microchip Technology Inc.
DS00557C-page 27
AN557
0106 0107 0108 0109 010A 010B 010C 010D 010E 010F 0110 1003 3010 00A6 01A2 01A3 01A4 0DA1 0DA0 0DA4 0DA3 0DA2 00441 00442 00443 00444 00445 00446 00447 00448 00449 00450 00451 00452 00453 00454 00455 00456 00457 00458 00459 00460 00461 00462 00463 00464 00465 00466 00467 00468 00469 00470 00471 00472 00473 00474 00475 00476 00477 00478 00479 00480 00481 00482 00483 00484 00485 00486 00487 B2_BCD bcf movlw movwf clrf clrf clrf rlf rlf rlf rlf rlf decfsz goto RETLW ; adjDEC movlw movwf call movlw movwf call ; movlw movwf call ; goto ; adjBCD movlw addwf movwf btfsc movwf movlw addwf movwf btfsc movwf RETLW loop16 3 0,W temp temp,3 0 30 0,W temp temp,7 0 0 R0 FSR adjBCD STATUS,0 .16 count R0 R1 R2 L_byte, F H_byte, F R2, F R1, F R0, F count, F adjDEC 0 R2 FSR adjBCD R1 FSR adjBCD ; clear the carry bit
loop16
;
0111 0BA6 0112 2914 0113 3400 0114 3024 0115 0084 0116 211E 0117 3023 0118 0084 0119 211E 011A 3022 011B 0084 011C 211E 011D 290C 011E 011F 0120 0121 0122 0123 0124 0125 0126 0127 0128 3003 0700 00A7 19A7 0080 3030 0700 00A7 1BA7 0080 3400
;
; test if result > 7
; test if result > 7 ; save as MSD
; ; ; ; end
MEMORY USAGE MAP ('X' = Used, 0000 0040 0080 00C0 0100 : : : : : X---XXXXXXXXXXXX XXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXX
'-' = Unused) XXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXX XXXXXXXXX------XXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXX ----------------
XXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXX
All other memory blocks unused. Program Memory Words Used: Program Memory Words Free: 294 730
Errors : Warnings : Messages :
0 0 reported, 0 reported,
0 suppressed 7 suppressed
DS00557C-page 28
© 1997 Microchip Technology Inc.
WORLDWIDE SALES & SERVICE
AMERICAS
Corporate Office
Microchip Technology Inc. 2355 West Chandler Blvd. Chandler, AZ 85224-6199 Tel: 602-786-7200 Fax: 602-786-7277 Technical Support: 602 786-7627 Web: http://www.microchip.com
ASIA/PACIFIC
Hong Kong
Microchip Asia Pacific RM 3801B, Tower Two Metroplaza 223 Hing Fong Road Kwai Fong, N.T., Hong Kong Tel: 852-2-401-1200 Fax: 852-2-401-3431
EUROPE
United Kingdom
Arizona Microchip Technology Ltd. Unit 6, The Courtyard Meadow Bank, Furlong Road Bourne End, Buckinghamshire SL8 5AJ Tel: 44-1628-851077 Fax: 44-1628-850259
France
Arizona Microchip Technology SARL Zone Industrielle de la Bonde 2 Rue du Buisson aux Fraises 91300 Massy, France Tel: 33-1-69-53-63-20 Fax: 33-1-69-30-90-79
Atlanta
Microchip Technology Inc. 500 Sugar Mill Road, Suite 200B Atlanta, GA 30350 Tel: 770-640-0034 Fax: 770-640-0307
India
Microchip Technology India No. 6, Legacy, Convent Road Bangalore 560 025, India Tel: 91-80-229-0061 Fax: 91-80-229-0062
Boston
Microchip Technology Inc. 5 Mount Royal Avenue Marlborough, MA 01752 Tel: 508-480-9990 Fax: 508-480-8575
Korea
Microchip Technology Korea 168-1, Youngbo Bldg. 3 Floor Samsung-Dong, Kangnam-Ku Seoul, Korea Tel: 82-2-554-7200 Fax: 82-2-558-5934
Germany
Arizona Microchip Technology GmbH Gustav-Heinemann-Ring 125 D-81739 Müchen, Germany Tel: 49-89-627-144 0 Fax: 49-89-627-144-44
Chicago
Microchip Technology Inc. 333 Pierce Road, Suite 180 Itasca, IL 60143 Tel: 630-285-0071 Fax: 630-285-0075
Italy
Arizona Microchip Technology SRL Centro Direzionale Colleone Palazzo Taurus 1 V. Le Colleoni 1 20041 Agrate Brianza Milan, Italy Tel: 39-39-6899939 Fax: 39-39-6899883
Shanghai
Microchip Technology RM 406 Shanghai Golden Bridge Bldg. 2077 Yan'an Road West, Hongiao District Shanghai, PRC 200335 Tel: 86-21-6275-5700 Fax: 86 21-6275-5060
Dallas
Microchip Technology Inc. 14651 Dallas Parkway, Suite 816 Dallas, TX 75240-8809 Tel: 972-991-7177 Fax: 972-991-8588
Singapore
Microchip Technology Taiwan Singapore Branch 200 Middle Road #10-03 Prime Centre Singapore 188980 Tel: 65-334-8870 Fax: 65-334-8850
JAPAN
Microchip Technology Intl. Inc. Benex S-1 6F 3-18-20, Shin Yokohama Kohoku-Ku, Yokohama Kanagawa 222 Japan Tel: 81-4-5471- 6166 Fax: 81-4-5471-6122 5/8/97
Dayton
Microchip Technology Inc. Two Prestige Place, Suite 150 Miamisburg, OH 45342 Tel: 937-291-1654 Fax: 937-291-9175
Los Angeles
Microchip Technology Inc. 18201 Von Karman, Suite 1090 Irvine, CA 92612 Tel: 714-263-1888 Fax: 714-263-1338
Taiwan, R.O.C
Microchip Technology Taiwan 10F-1C 207 Tung Hua North Road Taipei, Taiwan, ROC Tel: 886 2-717-7175 Fax: 886-2-545-0139
New York
Microchip Technology Inc. 150 Motor Parkway, Suite 416 Hauppauge, NY 11788 Tel: 516-273-5305 Fa