Inter sur port B.pdf part of PIONEER KEH-1850 KEH-1800 Pioneer Keh 1800 Keh 1850 XM ES.pdf, KEH-1800 X1M/UC KEH-1850 X1M/UC XM/ES X1M/ES ETC... ORDER NO. CRT2266 text manual preview

Text preview for : Inter sur port B.pdf part of PIONEER KEH-1850 KEH-1800 KEH-1800 X1M/UC KEH-1850 X1M/UC XM/ES X1M/ES ETC... ORDER NO. CRT2266

Back to : Pioneer Keh 1800 Keh 1850 | Home

M
Author:

AN566
USING A PORTB INPUT FOR AN EXTERNAL INTERRUPT
The interrupt source(s) cannot simply be directly connected to the PORTB pins, and expect an interrupt to occur the same as on the interrupt (INT) pin. To develop the microcontrollers hardware/software to act as an interrupt by an external signal, we must know the characteristics of the external signal. After we know this, we can determine the best way to structure the program to handle this signal. The characteristics that we need to consider when developing the interrupt include: 1. 2. The rising edge and falling edges. The pulse width of the interrupt trigger (high time / low time).

Using the PORTB Interrupt on Change as an External Interrupt
Mark Palmer Microchip Technology Inc.

INTRODUCTION
The PICmicroTM families of RISC microcontrollers are designed to provide advanced performance and a cost-effective solution for a variety of applications. To address these applications, there is the PIC16CXXX microcontroller family of products. This family has numerous peripheral and special features to better address user applications. The feature this application note will focus on is the Interrupt on Change of the PORTB pins. This "interrupt on change" is triggered when any of the RB7:RB4 pins, configured as an input, changes level. When this interrupt is used in conjunction with the software programmable weak internal pull-ups, a direct interface to a keypad is possible. This is shown in application note AN552, Implementing Wake-up on Key Stroke. Another way to use the "interrupt on change" feature would be as additional external interrupt sources. This allows PIC16CXXX devices to support multiple external interrupts, in addition to the built-in external interrupt on the INT pin. This application note will discuss some of the issues in using PORTB as additional external interrupt pins, and will show some examples. These examples can be easily modified to suit your particular needs.

It is easy to understand the need of knowing about which edge triggers the interrupt service routine for the external interrupt. This allows one to ensure that the interrupt service routine is only entered for the desired edge, with all other edges ignored. Not so clear is the pulse width of the interrupt's trigger. This characteristic helps determine the amount of additional overhead that the software routine may need.

© 1997 Microchip Technology Inc.

DS00566B-page 1

AN566
Figure 1 shows the two cases for the interrupt signal verses the time to complete the interrupt service routine. The first waveform is when the signal makes the low-to-high-to-low transitions before the interrupt service routine has completed (interrupt flag cleared). When the interrupt flag has been cleared, the interrupt signal has already returned to the inactive level. The next transition of the signal is due to another interrupt request. An interrupt signal with this characteristic will be called a small pulse width signal. The second waveform is when the signal only makes the low-to-high transitions before the interrupt service routine has completed (interrupt flag cleared). The next transition (high-to-low) will return the interrupt signal to the inactive level. This will generate a "false" interrupt, that will need to be cleared. Then the following transition (low-to-high) will be a "true" interrupt. An interrupt signal with this characteristic will be called a wide pulse width signal. An interrupt pulse with a small pulse width requires less overhead than a wide pulse width. A small pulse width signal must be less than the minimum execution time of the interrupt service routine, while a wide pulse width must be greater then the maximum time through the interrupt service routine. Example 1 shows a single interrupt source on PORTB (RB7), which executes the interrupt service routine on a rising edge. The interrupt source has a small pulse width. In this case, since the interrupt pulse width is small, the pulse has gone high and then low again before PORTB is read to end the mismatch condition. So when PORTB is read it will read a low signal and will again be waiting for the rising edge transition.

FIGURE 1:

INTERRUPT STEPS FOR SMALL AND WIDE PULSE WIDTHS

Small Pulse Width

RBx Rising Edge Triggers Interrupt PORTB Interrupt Service Routine is complete. PORTB Interrupt Flag is cleared, mismatch is ended. Wait for next interrupt edge. Signal returns to "Inactive State".

Large Pulse Width RBx Rising Edge Triggers Interrupt PORTB Interrupt Service Routine is complete. PORTB Interrupt Flag is cleared, mismatch is ended. Wait for next interrupt edge. Falling Edge Triggers "False" Interrupt PORTB Interrupt Service Routine is complete. PORTB Interrupt Flag is cleared, mismatch is ended. Wait for "False" interrupt edge.

EXAMPLE 1:

SINGLE INTERRUPT WITH A SMALL PULSE WIDTH
BTFSS GOTO INTCON, RBIF OTHER_INT : : PORTB, 1 INTCON, RBIF : : RETFIE ; ; ; ; ; ; ; ; ; PortB interrupt? Other interrupt Do task for INT on RB7 Read PortB (to itself) to end mismatch condition Clear the RB interrupt flag. Return from interrupt Do what you need to here

PER_INT

CLR_RBINTF

MOVF BCF RETFIE

OTHER_INT

; Return from interrupt

DS00566B-page 2

© 1997 Microchip Technology Inc.

AN566
Example 2 shows a single interrupt source on PORTB (RB7), which executes the interrupt service routine on a rising edge. The interrupt source has a wide pulse width. In this case since the interrupt pulse width is large, the pulse is still high before PORTB is read to end the mismatch condition. So when PORTB is read it will read a high signal and will generate an interrupt on the next falling edge transition (which should be ignored).

EXAMPLE 2:

SINGLE INTERRUPT WITH A WIDE PULSE WIDTH
BTFSS GOTO BTFSC GOTO : INTCON, RBIF OTHER_INT PORTB, RB7 CLR_RBINTF : : PORTB, 1 ; ; ; ; ; ; ; ; ; ; ; PortB interrupt? Other interrupt Check for rising edge Falling edge, clear PortB int flag Do task for INT on RB7 Read PortB (to itself) to end mismatch condition Clear the RB interrupt flag. Return from interrupt Do what you need to here

PER_INT

CLR_RBINTF

MOVF

OTHER_INT

BCF INTCON, RBIF RETFIE : : RETFIE

; Return from interrupt

Example 3 shows an interrupt on change with the interrupt source on PORTB (RB7). This executes the interrupt service routine on a both edges. The interrupt source must have a minimum pulse width to ensure that both edges can be "seen". The minimum pulse width is the maximum time from the interrupt edge to the reading of PORTB and clearing the interrupt flag.

EXAMPLE 3:

INTERRUPT ON CHANGE
BTFSS GOTO MOVF BCF INTCON, RBIF OTHER_INT PORTB, 1 INTCON, RBIF : : ; ; ; ; ; ; ; ; ; PortB interrupt? Other interrupt Read PortB (to itself) to end mismatch condition Clear the RB interrupt flag. Do task for INT on RB7 Return from interrupt Do what you need to here

PER_INT CLR_RBINTF

RETFIE OTHER_INT : RETFIE

; Return from interrupt

© 1997 Microchip Technology Inc.

DS00566B-page 3

AN566
USING PORTB INPUTS FOR MULTIPLE INTERRUPTS
The previous examples have been for a single external interrupt on PORTB. This can be extended to support up to four external interrupts. To do this requires additional software overhead, to determine which of the PORTB pins (RB7:RB4) caused the interrupt. Care should be taken in the software to ensure that no interrupts are lost. In this example, the interrupt sources on RB7, RB5, and RB4 have a small pulse width, while the interrupt source on pin RB6 is wide and should cause a trigger on the rising edge.

SUMMARY
The PORTB interrupt on change feature is both a very convenient method for direct interfacing to an external keypad, with no additional components, but is also versatile in its uses the ability to add up to four additional external interrupts. Of course hybrid solutions are also possible. That is, for example, using PORTB<6:1> as a 3x3 keypad, with PORTB<7> as an external interrupt and PORTB<0> as a general purpose I/O. The flexibility of this feature allows the user to implement a best fit design for the application.

EXAMPLE 4:
PER_INT

MULTIPLE INTERRUPTS WITH DIFFERENT PULSE WIDTHS
BTFSS GOTO INTCON, RBIF OTHER_INT ; PortB interrupt? ; Other interrupt

; ; PortB change interrupt has occurred. Must determine which pin caused ; interrupt and do appropriate action. That is service the interrupt, ; or clear flags due to other edge. ; MOVF PORTB, 0 ; Move PortB value to the W register ; This ends mismatch conditions MOVWF TEMP ; Need to save the PortB reading. XORWF LASTPB, 1 ; XOR last PortB value with the new ; PortB value. CK_RB7 BTFSC LASTPB, RB7 ; Did pin RB7 change CALL RB7_CHG ; RB7 changed and caused the interrupt CK_RB6 BTFSC LASTPB, RB6 ; Did pin RB6 change CALL RB6_CHG ; RB6 changed and caused the interrupt CK_RB5 BTFSC LASTPB, RB5 ; Did pin RB5 change CALL RB5_CHG ; RB5 changed and caused the interrupt CK_RB4 BTFSC LASTPB, RB4 ; Did pin RB4 change GOTO RB4_CHG ; RB4 changed and caused the interrupt ; RB7_CHG : ; Do task for INT on RB7 : ; RETURN RB6_CHG BTFSC PORTB, RB6 ; Check for rising edge RETURN ; Falling edge, Ignore : ; Do task for INT on RB6 : RETURN RB5_CHG : ; Do task for INT on RB5 : ; RETURN RB4_CHG : ; Do task for INT on RB4 : ; CLR_RBINTF MOVF TEMP, 0 ; Move the PortB read value to the MOVWF LASTPB ; register LASTPB BCF INTCON, RBIF ; Clear the RB interrupt flag. RETFIE ; Return from interrupt ; OTHER_INT : ; Do what you need to here : RETFIE ; Return from interrupt

DS00566B-page 4

© 1997 Microchip Technology Inc.

WORLDWIDE SALES & SERVICE
AMERICAS
Corporate Office
Microchip Technology Inc. 2355 West Chandler Blvd. Chandler, AZ 85224-6199 Tel: 602-786-7200 Fax: 602-786-7277 Technical Support: 602 786-7627 Web: http://www.microchip.com

ASIA/PACIFIC
Hong Kong
Microchip Asia Pacific RM 3801B, Tower Two Metroplaza 223 Hing Fong Road Kwai Fong, N.T., Hong Kong Tel: 852-2-401-1200 Fax: 852-2-401-3431

EUROPE
United Kingdom
Arizona Microchip Technology Ltd. Unit 6, The Courtyard Meadow Bank, Furlong Road Bourne End, Buckinghamshire SL8 5AJ Tel: 44-1628-851077 Fax: 44-1628-850259

France
Arizona Microchip Technology SARL Zone Industrielle de la Bonde 2 Rue du Buisson aux Fraises 91300 Massy, France Tel: 33-1-69-53-63-20 Fax: 33-1-69-30-90-79

Atlanta
Microchip Technology Inc. 500 Sugar Mill Road, Suite 200B Atlanta, GA 30350 Tel: 770-640-0034 Fax: 770-640-0307

India
Microchip Technology India No. 6, Legacy, Convent Road Bangalore 560 025, India Tel: 91-80-229-0061 Fax: 91-80-229-0062

Boston
Microchip Technology Inc. 5 Mount Royal Avenue Marlborough, MA 01752 Tel: 508-480-9990 Fax: 508-480-8575

Korea
Microchip Technology Korea 168-1, Youngbo Bldg. 3 Floor Samsung-Dong, Kangnam-Ku Seoul, Korea Tel: 82-2-554-7200 Fax: 82-2-558-5934

Germany
Arizona Microchip Technology GmbH Gustav-Heinemann-Ring 125 D-81739 Müchen, Germany Tel: 49-89-627-144 0 Fax: 49-89-627-144-44

Chicago
Microchip Technology Inc. 333 Pierce Road, Suite 180 Itasca, IL 60143 Tel: 630-285-0071 Fax: 630-285-0075

Italy
Arizona Microchip Technology SRL Centro Direzionale Colleone Palazzo Taurus 1 V. Le Colleoni 1 20041 Agrate Brianza Milan, Italy Tel: 39-39-6899939 Fax: 39-39-6899883

Shanghai
Microchip Technology RM 406 Shanghai Golden Bridge Bldg. 2077 Yan'an Road West, Hongiao District Shanghai, PRC 200335 Tel: 86-21-6275-5700 Fax: 86 21-6275-5060

Dallas
Microchip Technology Inc. 14651 Dallas Parkway, Suite 816 Dallas, TX 75240-8809 Tel: 972-991-7177 Fax: 972-991-8588

Singapore
Microchip Technology Taiwan Singapore Branch 200 Middle Road #10-03 Prime Centre Singapore 188980 Tel: 65-334-8870 Fax: 65-334-8850

JAPAN
Microchip Technology Intl. Inc. Benex S-1 6F 3-18-20, Shin Yokohama Kohoku-Ku, Yokohama Kanagawa 222 Japan Tel: 81-4-5471- 6166 Fax: 81-4-5471-6122 5/8/97

Dayton
Microchip Technology Inc. Two Prestige Place, Suite 150 Miamisburg, OH 45342 Tel: 937-291-1654 Fax: 937-291-9175

Los Angeles
Microchip Technology Inc. 18201 Von Karman, Suite 1090 Irvine, CA 92612 Tel: 714-263-1888 Fax: 714-263-1338

Taiwan, R.O.C
Microchip Technology Taiwan 10F-1C 207 Tung Hua North Road Taipei, Taiwan, ROC Tel: 886 2-717-7175 Fax: 886-2-545-0139

New York
Microchip Technology Inc. 150 Motor Parkway, Suite 416 Hauppauge, NY 11788 Tel: 516-273-5305 Fax: 516-273-5335

San Jose
Microchip Technology Inc. 2107 North First Street, Suite 590 San Jose, CA 95131 Tel: 408-436-7950 Fax: 408-436-7955

Toronto
Microchip Technology Inc. 5925 Airport Road, Suite 200 Mississauga, Ontario L4V 1W1, Canada Tel: 905-405-6279 Fax: 905-405-6253

All rights reserved. © 1997, Microchip Technology Incorporated, USA. 6/97
Information contained in this publication regarding device applications and the like is intended for suggestion only and may be superseded by updates. No representation or warranty is given and no liability is assumed by Microchip Technology Incorporated with respect to the accuracy or use of such information, or infringement of patents or other intellectual property rights arising from such use or otherwise. Use of Microchip's products as critical components in life support systems is not authorized except with express written approval by Microchip. No licenses are conveyed, implicitly or otherwise, under any intellectual property rights. The Microchip logo and name are registered trademarks of Microchip Technology Inc. in the U.S.A. and other countries. All rights reserved. All other trademarks mentioned herein are the property of their respective companies.

M

© 1997 Microchip Technology Inc.

DS00566B-page 5