Text preview for : Alignment & Adjustment.pdf part of Samsung CW683CW Some IC LA7845 MSP3411G-A2 TDA7297 VDP3112B 24L161 SDA555X-OTP



Back to : Samsung CW683CW.rar | Home

Alignment and Adjustments

4. Alignment and Adjustments
4-1 General Alignment Instructions
1. Usually, a color TV-VCR needs only slight touch-up adjustment upon installation. Check the basic characteristics such as height, horizontal and vertical sync and focus. 2. Observe the picture for good black and white details. There should be objectionable color shading; if color shading is present, demagnetize, perform purity and convergence adjustments described below. 3. Use the specified test equipment or its equivalent. 4. Correct impedance matching is essential. 8. To protect against shock hazard, use an isolation transformer. 5. Avoid overload. Excessive signal from a sweep generator might overload the front-end of the TV. When inserting signal markers, do not allow the marker generator to distort test results. 6. Connect the TV only to an AC power source with voltage and frequency as specified on the backcover nameplate. 7. Do not attempt to connect or disconnect any wires while the TV is turned on. Make sure that the power cord is disconnected before replacing any parts.

4-2 Automatic Degaussing
A degaussing coil is mounted around the picture tube, so that external degaussing after moving the TV should be unnecessary. But the receiver must be properly degaussed upon installation. The degaussing coil operates for about 1 second after the power is switched ON. If the set is moved or turned in a different direction, the power should be OFF for at least 10 minutes. If the chassis or parts of the cabinet become magnetized, poor color purity will result. If this happens, use an external degaussing coil. Slowly move the degaussing coil around the faceplate of the picture tube and the sides and front of the receiver. Slowly withdraw the coil to a distance of about 6 feet before turning power OFF. If color shading persists, perform the following Color purity and Convergence adjustments.

4-3 High voltage Check
CAUTION : There is no high voltage adjustment on this chassis. The B+ power supply should be +135 volts (with full color- bar input and normal picture level).

1. Connect a digital voltmeter to the second anode of the picture tube. 2. Turn on the TV. Set the Brightness and Contrast controls to minimum (zero beam current). 3. Adjust the Brightness and contrast controls to both extremes. Ensure that the high voltage does not exceed 32 KV under any conditions.

Samsung Electronics

4-1

Alignment and Adjustments

4-4 Dynamic Focus Adjustment
1. A dynamic focus adjustment should be done after replacing the CRT PCB, FBT or CRT. 2. Input a crosshatch pattern.

3. Enter " STANDARD " in video mode. 4. Turn the Dynamic focus VR fully clockwise (maximum).( ) 5. Turn the Static focus VR fully counterclockwise (maximum).( ) 6. Slowly turn the static focus VR counterclockwise. Adjust until the vertical line in the middle of the screen has maximum clarity.( ) 7. Slowly turn the dynamic focus VR (clockwise) and adjust the 3rd horizontal line for maximum clarity.( ) 8. Repeat 4-7, if necessary.




H

STATIC FOCUS VR


V

DYNAMIC FOCUS VR

SCREEN

4-5 SCREEN Adjustment
1. Input Toshiba Pattern 2. Enter "Service Mode".(Refer to "Service Mode") 3. Select "G2-Adjust". 4. Set the values as below. 29 Inch IBRM = 220 WDRV = 35 CDL = 220 COLR G B = 150 150 150 21 Inch IBRM = 220 WDRV = 35 CDL = 165 COL = 70

4-2

Samsung Electronics

Alignment and Adjustments

5. Turn the SCREEN VR until "MRCR G B" and "MRWDG" are green and those value are about 100. (The incorrect SCREEN Voltage may result that "MRCR G B" and "MRWDG" should be red)

Note 1. When you do not have Toshiba Pattern, follow this method. 1. 2. 3. 4. 5. Set the TV on the condition that AV mode no signal(black) Enter the "Menu" and set the mode to blue screen off. Enter the "Service Mode". Select " G2-Adjust". Set the values as below. IBRM = 220 WDRV = 35 CDL = 220 COLR G B = 150 150 150 6. Turn the SCREEN VR until the value of " MRCR G B" is about 120. Do not mind that the "OSD" Color is red.

s After completing G2-Adjust, follow this procedure. x Enter the "Video Adjust 1". Choose any item in menu. (ex. Select "Red Cutoff") Change the value of item you select, and recover the value.
For example, when the value of "Red Cutoff" is 127, change the value to 128 and restore the value to 127. If you do not follow this procedure, the picture may be abnormal. For example, when the TV set is on, the picture becames brighter gradually.

Samsung Electronics

4-3

Alignment and Adjustments

4-6 E2PROM (IC902) Replacement
1. When IC902 is replaced, all adjustment data revert to the initial values. So, all adjustment values when servicing should be readjusted. 2. After IC902 is replaced, connect the AC power supply cord. 3. Turn the power switch ON. 4. In stand-by, warm up the TV for at least 10 seconds. 5. Power on the TV.

4-7 White Balance Adjustment
s Equipment : Color-Analyzer (CA-100) s Input Signal : Pattern signal (Toshiba pattern) 1. Select STANDARD from the menu. 2. Input an 100% White pattern. 3. Enter the "Service Mode". (Refer to "4-8 Service Mode") 4. Warm up the TV set at least for 30 minutes. 5. Input a Toshiba pattern signal. 6. Enter the "Video Adjust1". - Adjust "Sub Contrast" so that Y (luminance) becomes 40 ft ± 3. - Use "Red Drive" and " Blue Drive" to adjust High-Light (x : 290, y : 300) - Adjust "Sub Bright" so that Y (luminance) becomes 1.3ft ± 0.3. - Use "Red Cutoff" and "Blue Cutoff" to adjust Low-Light (x : 290, y : 300). 7. Adjust CA-100 so that the final adjustment value can be fixed. 8. Use the Channel Up/Down (v/w) buttons to move the cursor on the adjustment modes. 9. Use the Volume +/- buttons to change the adjustment value.

4-4

Samsung Electronics

Alignment and Adjustments

4-8 Factory Adjustment
4-8-1 Service Mode
1. To enter the "Service Mode", Press the remote-control keys in this sequence : - If you do not have Factory remote-control
PICTURE OFF DISPLAY ( ) MENU MUTE PICTURE ON

- If you have Factory remote-control
PICTURE ON DISPLAY ( ) FACTORY

2. After the Service Mode is entered, the initial screen is as shown in the figure below.
Service Deflection Video Adjust 1 Video Adjust 2 Video Adjust 3 Option(81h 0Ch) Reset G2-Adjust Others

*

These hexa * depends on digits are check sum value which the MICOM. If check sum value is changed, the value of 2 E PROM Data newly initialed.

3. Use the Channel Up/Down buttons to move the cursor in the adjustment parameters. Note 2. - When CRT, CRT PCB, FBT, E PROM (sometimes MICOM) is replaced, the adjustment values should be controlled. - After the Service adjustment is completed, Do not select "Reset" in the service mode menu. (After above procedure is done, power is on initially and the "Plug and Play" will be operated.)
2

Samsung Electronics

4-5

Alignment and Adjustments

4-8-2 Memory Data
4-8-2(A) DEFLECTION (GEOMETRIC ADJUSTMENT VALUE)
Fixed Value No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 OSD V Shift V Amp V Slope V SC H EW H Trapizium H Parabola H Symmetry H Corner H Shift PIP Contrast PIP Tint PIP PAL V Pos PIP NTSC V Pos PIP H Pos PIP BLKLG Range -128 ~127 -128 ~127 -128 ~127 -128 ~127 -128 ~127 -128 ~127 -128 ~127 -128 ~127 -128 ~127 -128 ~127 0 ~ 15 0 ~ 63 0 ~ 255 0 ~ 255 0 ~ 255 0 ~ 15 Initial Value -30 -7 -3 -17 73 -47 -7 13 23 13 8 0 26 23 30 6 Function Adjust Vertical Picture Position Adjust Vertical Picture Size Adjust Vertical Slope Correction Adjust Vertical S-Correction Adjust Horizontal Picture Size Adjust Horizontal Trapeziod Adjust Horizontal Parabola Wave Adjust Horizontal Symmetry Adjust Horizontal Corner Adjust Horizontal Position Adjust PIP Contrast Adjust PIP Tinit Adjust PIP Vertical Position (Main Picture is PAL) Adjust PIP Vertical Position (Main Picture is NTSC) Adjust PIP Horizontal Position Adjust PIP Green Cutoff Level Not to be adjusted Not to be adjusted Remark

4-6

Samsung Electronics

Alignment and Adjustments

4-8-2(B) SCREEN CHANGE (I2C BUS GEOMETRIC ADJUSTMENT)

1

V Shift

6

V Amp

2

V Slope

7

V SC

3

H EW

8

H Trapizium

4

H Parabola

9

H Symmetry

5

H Corner

10

H Shift

Samsung Electronics

4-7

Alignment and Adjustments

4-8-2(C) VIDEO ADJUST 1
Fixed Value No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 OSD Red Cufoff Green Cutoff Blue Cutoff Red Drive Green Drive Blue Drive Sub Bright Sub Contrast Sub Color Sub Tint BCL Threshold BCL Gain BCL Time TTX Contrast YC Delay Range Initial Value 0 ~255 0 ~255 0 ~255 0 ~255 0 ~255 0 ~255 0 ~ 200 0 ~ 13 0 ~ 27 0 ~ 100 0 ~ 255 0 ~ 15 0 ~ 15 0 ~ 255 0~8 127 127 127 127 127 127 100 50 27 80 65 8 9 90 * Adjust OSD/TTX Contrast Refer to Table 1 Adjust Beam Control Limit Refer to Note 3 Not to be adjusted Adjust Red Cutoff Level Adjust Green Cutoff Level Adjust Blue Cutoff Level Adjust Red Output Gain Adjust Green Output Gain Adjust Blue Output Gain Adjust Brightness Level Adjust Contrast Level Adjust Color Level Adjust Tint Low Light High Light High Light Low Light Function Remark

Note 3. Beam Control Limit Characteristic
beam
MIN 1.8mA 1.6mA BCL THESHOLD BCL GAIN MAX

WDRGB

50

IRE

Table 1. YC Delay Adjustment Table YC Delay Value PAL Def. 4 BG 3 DK 6 I 6 L 7 Def. 1 BG 1 SECAM DK 5 I 8 L 5 NTSC Def. 4 M 3

The "Def." means that TV is in AV mode.

4-8

Samsung Electronics

Alignment and Adjustments

4-8-2(D) VIDEO 2 ADJUST
Fixed Value No. 1 2 3 4 5 6 7 8 OSD B stretch-BTHR B stretch-BTLT B stretch-BAM Coring RGB Bright RGB Contrast EHT Time EHT Compensation Range 0 ~ 55 0 ~ 15 0 ~ 31 10 ~ 31 0 ~ 255 0 ~ 255 0 ~ 15 0 ~ 255 Initial Value 50 8 4 20 45 15 0 90 Black Stretch Threshold Black Stretch Tilt Position Black Stretch Amount Luma Peaking Filter Coring OSD/TTX RGB Bright OSD/TTX RGB Contrast Electronic High Tension Response Time Electronic High Tension Coefficient Function Remark

Coring : The Value of Center Frequency for the active bandwidth.

4-8-2(E) VIDEO 3 ADJUST
No. 1 2 3 4 5 6 7 OSD Peak Threshold Soft Limit Slope B Hard Limit Peak Video Ref Peak Video Gain Range Initial Value 0 ~ 255 0 ~ 15 0 ~ 255 0~4 0~5 185 4 255 0 0 33 39 Function White Peak Level Threshold Refer to Picture Below White Peak Level Threshold Reference White Peak Level Threshold Gain Auto Color Control Refer to Note Below Remark

ACC-REF(PAL/NTSC) 0 ~ 40 ACCR(SECAM) 0 ~ 39

Note 4. Soft Limit & Hard Limit

Output 511

Part 1

Part 2
Slope 1 [0...15]

Hard limiter

0 2 4 6 8 10 12 14
Slope 2 [0...15]

400

300

200

0 2 4 6 8 10 12 14

Soft Limit Slope B
range=256...511

"Soft Limit" is that Limitting the peak white without feed-back, but "Peak Limit" is that with feed-back for white peak level

100 tilt 1 [0...511] 0 0 100 200 300 400 500 600 700 800 900 tilt 2 [0...511] Li 1023

Samsung Electronics

4-9

Alignment and Adjustments

4-8-2(E) OPTION
Fixed Value No. 1 2 3 4 5 6 7 8 9 Language Sound CRT AV Mode X-Ray Tilt Control Auto FM PIP Txt Language OSD Initial Value Arab, Iran, Lybya, CIS A2/NICAM, V-Dolby, Mono, L-Stereo 4:3, Wide, Q(12.8:9), 4:3-16:9, Q-16:9 2Scart, 2Scart+S, 1RCA, 2RCA, 2RCA+S, 2RCA+D, 2RCA+S+D, 1Scart Off, On Off, On Off, On 2-Tuner, 1-Tuner, Off Arabic, Farsi, Arab-Hebrew, West Europe, East Europe, Russian, Greek-Turkey Off, On Off, On Off, On Off, On Without "TV/VIDEO" key in the front panel, set to "On" When PIP is "2-Tuner", set to "ON" Function Remark OSD Language
Depending on IC601 Refer to Note 5

S:S-VHS, D:DVD

10 11 12 13

LNA Equalizer High Deviate TTX On/Off

14

AV by CH key

Off, On

Initial Value : Refer to Note 6 on the next page.

Note 5. Sound A2/NICAM V-DOLBY Mono L-Stereo MSP3400D, MSP3410D MSP3411G Not used this mode for KS3A Chassis IC601

4-10

Samsung Electronics

Alignment and Adjustments

Note 6. Option. CS29A5WT8X/UMG Description LANGUAGE SOUND CRT AV MODE X-RAY TILT CONTROL AUTO FM PIP TEXT LANGUAGE LNA EQUALIZER HIGH DEVIATE TTX ON/OFF AV BY CH KEY OPTION BYTE Initial Vaue Arab V-Dolby 4:3 2 RCA + S OFF ON ON OFF Arabic OFF ON ON ON ON 84 CC D8 CS29A6PF8X/HAC Initial Vaue Arab V-Dolby 4:3 2 RCA + S OFF ON ON 2-Tuner Farsi ON ON ON ON OFF 85 DC 5E CS29A6WT8X/BWT Initial Vaue CIS A2/Nicam 4:3 2 SCART + S OFF ON ON OFF RUSSIAN OFF ON ON ON OFF 83 AC 28 CS29A5MT9X/BWT Initial Vaue CIS A2/Nicam 4:3 2 SCART + S OFF ON ON 2-Tuner RUSSIAN ON ON ON ON ON 83 AC AE

4-8-2(F) OTHERS
Fixed Value No. 1 2 3 4 5 6 7 8 OSD VSU H QEW H ZOOM Parabola H 16:9 Parabola TTX H Shift Range 96 ~ 111 -30 ~ 30 -30 ~ 30 -30 ~ 30 -30 ~ 30 Initital Value 98 0 8 -15 6 BG 2 8 Adjust Melody Volumn Adjust Horizontal Parabola in Zoom Mode Adjust Horizontal Parabola in 16:9 Mode Adjust Horizontal OSD/TTX Position Vertical Set Up Time Function Remark

Mono Sound System BG/DK/I/M V Slice Level Melody Volumn 0~3 0 ~ 20

Samsung Electronics

4-11

Alignment and Adjustments

4-9 MICOM
4-9-1 Pin Layout

Write Protect EEPROM SDA EEPROM SCL Bus-Stop Main SDA Main SCL Sound Reset Video Reset VDD 2.5V GND VDD 3.3V CVBS Input VDD 2.5V GND AFT Scart1 Ident Scart2 Ident Key 1 H-Sync V-Sync Key 3 Key 2 X-Ray Protect IR Input Stand-By LED Time LED

1 2 3 4 5 6 7 8 9 10 11 12 13 14

I/O I/O IO I/O I/O I/O I/O I/O

PWM I/O I/O

52 51 50 49 48 47 46 45

15 ADC 16 ADC 17 ADC 18 ADC 19 20 21 I/O 22 I/O 23 I/O 24 I/O 25 I/O 26 I/O

S D A 5 5 5 X

44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 I/O 27

Tilt N.C. Power Sound Mute N.C. N.C. PX. Y PX. Y VDD 3.3V GND VDD 2.5V CORE OSD-B OSD-G OSD-R VDD 2.5V GND X-TAL Out X-TAL In MICOM Reset N.C. N.C. VDD 3.3V GND N.C. Relay

4-12

Samsung Electronics

Alignment and Adjustments

4-9-2 Pin Assignment Specification

PIN NO FUNCTION 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 I/O I/O I/O I/O I/O I/O I/O I/O Vdd GND Vdd CVBS Vdd GND ADC ADC ADC ADC HS VS I/O I/O I/O I/O I/O I/O

ASSIGN Write Protect ROM SDA ROM SCL Bus Stop Main SDA Main SCL Sound Reset Video Reset VDD 2.5V

IN/OUT Out I/O I/O In I/O I/O Out Out

ACTIVE H/L Low

DESCRIPTION EEPROM Write Protection EEPROM Serial Data Line EEPROM Serial Clock Line

Low

Disable Micom IIC Peripheral IC Serial Data Line

Low Low

Peripheral IC Serial Clock Line MSP IC Initial Control VDP IC Initial Control

VDD 3.3V CVBS Input VDD 2.5V In TTX CVBS Input Analog B+ Analog Ground AFT SC1-ID SC2-ID Key1 H-Sync V-Sync Key3 Key2 X-Ray IR-In STD-LED TIM-LED In In In In In In In In In In Out Out Auto Fine Tuning Control Scart1 Ident Scart2 Ident Key1 Input Horizontal Sync Input Vertical Sync Input Key3 Input Key2 Input X-Ray Protection Remocon Signal Input LED Drive Output(Red) LED Drive Output(Green)

Samsung Electronics

4-13

Alignment and Adjustments

4-9-2 Pin Assignment Specification (Continued)
PIN NO FUNCTION 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 I/O N.C. GND Vdd N.C. N.C. Reset X-In X-Out GND Vdd R G B COR Vdd GND Vdd I/O I/O N.C. Not Used (Programmed Gound Level) N.C. I/O I/O N.C. I/O Tilt Out PWM S-Mute Power Out Out High Low Sound Amp Mute Picture On/Off Control Not Used (Programmed Gound Level) Tilt Control Output VDD 3.3V PX.Y PX.Y In When The Caption Function Adopted, Used. Out VDD 2.5V OSD-R OSD-G OSD-B CORE VDD 2.5V Out Out Out Out Reset X-TAL In X-TAL Out In In Out Low 6MHz 6MHz VDD 3.3V ASSIGN Relay

IN/OUT Out

ACTIVE H/L Low

DESCRIPTION Activate Degausssing Coil Not Used (Programmed Gound Level) Analog Ground Not Used (Programmed Gound Level) Not Used (Programmed Gound Level) Micom Hardware Reset Crystal Oscillation Input Crystal Oscillation Output Analog Ground Analog B+ OSD/TTX Output (Red) OSD/TTX Output (Green) OSD/TTX Output (Blue) Fast Blank/Half Contrast Output

4-14

Samsung Electronics