710B.pdf part of Daewoo 710B 710B.pdf, Service Manual XGA COLOR MONITOR Model : 710B Acer text manual preview

Text preview for : 710B.pdf part of Daewoo 710B Service Manual XGA COLOR MONITOR Model : 710B Acer

Back to : 710B.pdf | Home

Service Manual
XGA COLOR MONITOR Model : 710B

DAEWOO ELECTRONICS CO., LTD OVERSEAS SERVICE DEPT.

CONTENTS
SAFETY PRECAUTIONS GENERAL SAFETY INFORMATION SERVICING PRECAUTIONS TECHNICAL INFORMATION GENERAL INFORMATION PIN CONNECTOR CAUTIONS FOR ADJUSTMENT AND REPAIR OPERATION & ADJUSTMENT TROUBLESHOOTING HINTS ALIGNMENT PROCEDURE BLOCK DIAGRAM PCB LAYOUT SCHEMATIC DIAGRAM EXPLODED VIEW DIAGRAM REPLACEMENT PARTS LIST CIRCUIT BOARD ELECTRICAL PARTS LIST 1 2 3 6 7 8 8 9 15 31 33 34 37 38 39 40

SAFETY PRECAUTIONS
CAUTION: No modifications of any circuit should be attempted. Service work should only be performed after you are thoroughly familiar with all of the following safety check and servicing guidelines.

Safety Check
Care should be taken while servicing this analog color display because of the high voltages used in the deflection circuits. These voltages are exposed in such areas as the associated flyback and yoke circuits.

Fire & Shock Hazard
· Insert an isolation transformer between the analog color display and AC power line before servicing chassis. · In servicing, pay attention to original lead dress especially in the high voltage circuit. if a short circuit is found, replace all parts which have been overheated as a result of the short circuit. · All the protective devices must be reinstalled per original design. · Soldering must be inspected for possible cold solder points, frayed leads, damaged insulation, solder splashes or sharp solder points. Be certain to remove all foreign materials.

Implosion Protection
Picture tube in this monitor employs integral implosion protection system, but care should be taken to avoid damage and scratching during installation. Use only same type replacement picture tubes. IMPORTANT SAFETY NOTICE: There are special components used in analog color display, which are important for safety. These parts are shaded on the schematic diagram and on the replacement parts list. It is essential that these critical parts should be replaced with manufacturer's specified parts to prevent X-radiation, shock, fire or other hazards. Do not modify the original design without getting a written permission from DAEWOO ELECTRONICS CO. or this will void the original parts and labor warranty.

X-Radiation
WARNING: The only potential source of X-Radiation is the picture tube. However when the high voltage circuitry is operating properly, there is no possibility of an X-Radiation problem. The basic precaution which must be exercised is to keep the high voltage at the following factory recommended level. NOTE: It is important to use an accurate, periodically calibrated high voltage meter. · To measure the high voltage, use a high-impedance high-voltage meter. Connect(-) to chassis and (+) to the CRT anode button. · Turn the Contrast & brightness control fully counterclockwise. · Measure the high voltage. The high voltage meter should indicate the following factory recommended level. · If the upper meter indication exceeds the maximum level, immediate service is required to prevent the possibility of premature component failure. · To prevent X-Radiation possibility, it is essential to use the specified picture tube. · The normal high voltage is 26.5KV or below, and must not exceed 29KV at zero beam current at rated voltage.

1

GENERAL SAFETY INFORMATION
Terms in the manual
CAUTION Statements identify conditions or practices that could result in damage to the equipment or other property. WARNING Statements identify conditions or practices that could result in personal injury or loss of life.

Terms as marked on equipment
CAUTION Statements indicate a personal injury hazard not immediately accessible as one reads the marking, or a hazard to properly including the equipment itself. WARNING Statements indicate a personal injury hazard immediately accessible as one reads the marking

Symbols in the manual
This symbol indicates where applicable cautionary or other information is to be found.

Symbols as marked on equipment
Protective GROUND terminal High Voltage Warning And Critical Component Warning Label Following warning label is on the CRT PWB shield case inside the unit. Warning: This product includes critical mechanical and electrical parts which are essential for x radiation safety. For continued safety, replace critical components indicated in the service manual only with exact replacement parts given in the parts list. Operating high voltage for this product is 29Kv at minimum brightness. Refer to service manual for measurement procedures and proper service adjustments.

2

SERVICING PRECAUTIONS
CAUTION: Before servicing instruments covered by this service manual, its supplements and addendum, read and follow the SAFETY PRECAUTIONS of this manual.

NOTE: If unforeseen circumstances create conflict between the following servicing precautions and any of the safety precautions on page 1 of this manual, always follow the safety precautions. Remember: Safety First.

General Servicing Precautions
1. Always unplug the AC power cord from the AC power source before: a. Removing or reinstalling any component, circuit board, module, or any other instrument assembly. b. Disconnecting or reconnecting any electrical plug or other electrical connection. c. Connecting a test substitute in parallel with an electrolytic capacitor in the instrument. CAUTION: A wrong part substitution or incorrect polarity installation of electrolytic capacitors may result in a explosion hazard. d. Discharging the picture tube anode. 2. Test high voltage only by measuring it with an appropriate high voltage meter or other voltage measuring device (DVM, FETVOM. etc.) equipped with a suitable high voltage probe. Do not test high voltage by "drawing an arc". 3. Discharge the picture tube anode only by: (a) first connecting one end of an insulated clip lead to the degaussing or line grounding system shield at the point where the picture tube socket ground lead is connected, and then (b) touching the other end of the insulated clip lead to the picture tube anode button, using an insulating handle to avoid personal contact with high voltage. 4. Do not any spray chemicals on or near this instrument or any or its assemblies. 5. Unless specified otherwise in this service manual, clean electrical contacts by applying the following mixture to the contacts with a pipe cleaner, cotton-tipped stick or comparable nonabrasive applicator: 10% (by volume) Acetone and 90% (by volume) isopropyl alcohol (90%-99% strength). CAUTION: This is a flammable mixture. Unless specified otherwise in this service manual, lubrication of contacts is not required. 6. Do not defeat any plug/socket B+ voltage interlocks with which instruments covered by this service manual might be equipped. 7. Do not apply AC power to this instrument and/or any of its electrical assemblies unless all solid-state device heat sinks are correctly installed. 8. Always connect the test instrument ground lead to the appropriate instrument chassis ground before connecting the test instrument positive lead. Always remove the test instrument ground lead last. 9. Use only the test fixtures specified in this service manual with this instrument. CAUTION: Do not connect the test fixture ground strap to any heatsink in this instrument.

3

Electrostatically Sensitive (ES) Devices
Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Electrostatically Sensitive (ES) Devices. The examples of typical ES devices are integrated circuits, some field-effect transistors and semiconductor "chip" components. The following techniques should be used to help reduce the incidence of component damage caused by static electricity. 1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any electrostatic charge on your body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging wrist strap device which should be removed for potential shock reasons prior to applying power to the unit under test. 2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as aluminum foil to prevent electrostatic charge buildup or exposure of the assembly. 3. Use only a grounded-tip soldering iron to solder or unsolder ES devices. 4. Use only an anti-static type solder removal device. Some solder removal devices not classified as "anti-static" can generate enough electrical charges to damage ES devices. 5. Do not use freon-propelled chemicals. These can generate enough electrical charges to damage ES devices. 6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or comparable conductive material). 7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material to the chassis or circuit assembly into which the device will be installed. CAUTION: Be sure that no power is applied to the chassis or circuit, and observe all other safety precautions. 8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmful motion such as the brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate enough static electricity to damage an ES devices).

General Soldering Guidelines
1. Use a grounded-tip, low-wattage soldering iron with appropriate tip size and shape that will maintain tip temperature within a 550°F-660°F (288°C-316°C) range. 2. Use an appropriate gauge of RMA resin-core solder composed of 60 parts tin/40 parts lead. 3. Keep the soldering iron tip clean. 4. Thoroughly clean the surface to be soldered. Use a small wire-bristle (0.5 inch or 1.25cm) brush with a metal handle. Do not use freon-propelled spray-on cleaners. 5. Use the following soldering technique: a. Allow the soldering iron tip to reach normal temperature (550°F to 660°F or 288°C to 316°C) b. Hold the soldering iron tip and solder strand against the component lead until the solder melts. c. quickly move the soldering iron tip to the junction of the component lead and the printed circuit foil, and hold it there only until the solder flows onto and around both the component lead and the foil. d. Closely inspect the solder area and remove any excess or splashed solder with a small wire-bristle brush. CAUTION: Work quickly to avoid overheating the circuit board printed foil.

4

FIGURE 1. USE SOLDERING IRON TO PRY LEADS

IC Removal/Replacement
Some utilized chassis circuit boards have slotted (oblong) holes through which the IC leads are inserted and then bent flat against the circuit foil. When holes are slotted, the following technique should be used to remove and replace the IC. When working with boards using the familiar round hole, use the standard technique as outlined in paragraphs 5 on the page under the title of general soldering guidelines.

Removal
1. Desolder and straighten each IC lead in one operation by gently prying up on the lead with the soldering iron tip as the solder melts. 2. Draw away the melted solder with an anti-static suction-type solder removal device (or with desoldering braid before removing the IC.

Replacement
1. Carefully insert the replacement IC in the circuit board. 2. Carefully bend each IC lead against the circuit foil pad and solder it. 3. Clean the soldered areas with a small wire-bristle brush. (lt is not necessary to reapply acrylic coating to the area).

"Small-Signal" Discrete Transistor Removal/Replacement
1. Remove the defective transistor by clipping its leads as close as possible to the component body. 2. Bend the end of each of three leads remaining on the circuit board into a "U" shape. 3. Bend the replacement transistor leads into a "U" shape. 4. Connect the replacement transistor leads to the corresponding leads extending from the circuit board and crimp the "U" with long nose pliers to insoure metal-to-metal contact, then solder each connection.

5

Power IC, Transistor or Devices Removal/Replacement
1. Heat and remove all solders from the device leads. 2. Remove the heatsink mounting screw (if applicable). 3. Carefully remove the device from the circuit board. 4. Insert new device in circuit board. 5. Solder each device lead, and clip off excess lead. 6. Replace heatsink.

Diode Removal/Replacement
1. Remove defective diode by clipping its leads as close as possible to diode body. 2. Bend the two remaining leads perpendicularly to the circuit board. 3. Observing diode polarity, wrap each lead out of the new diode around the corresponding lead on the circuit board. 4. Securely crimp each connection and solder it. 5. Inspect the solder joints of the two "original" leads on the circuit board copper side. If they are not shiny, reheat them and apply additional solder if necessary.

TECHNICAL INFORMATION
Picture Tube Type : 17-inch, Flat Square Tube type (16.2-inch, viewing area) Dot Pitch : 0.28mm Face Treatment : Non-glare / Anti-static Input Signal : R.G.B Analog Amp. Bandwidth : 85 MHz Input Sync : TTL, separate negative / positive Horizontal : 30-69 KHz Vertical : 50-160 Hz 1280 dots X 1024 lines (at 60Hz) Free Voltage (100-240 Vac, 50/60Hz) Standard Display Area : 310mm(H)X232mm(V) Full Screen Size : 330mm(H)X250mm(V) Max. 100W State On Stand-by Suspend Off Recovery Time None 3 seconds 7 seconds Power LED Green Green : 1 second Amber : 0.5 second Amber

Video

Scan Frequency Max. Resolution Power Source Display Area Power Consumption

Dimension Weight (Net/Gross) Operating Environment Storage Environment

424(W)X440(H)X447.2(D)mm (set with stand) 16.8/19.7 kg Temperature : 10-40°C/50-104°F Relative Humidity : 8-80% Temperature : -20-45°C/-4-113°F Relative Humidity : 5-90%

6

GENERAL INFORMATION
This color monitor automatically scans all horizontal frequencies from 30KHz to 69KHz, and all vertical frequencies from 50Hz to 160Hz. This color monitor adopted the OSD (On Screen Display), it shows the sync polarity and frequency and it provides that easily adjust control. This color monitor supports IBM PC, PC/XT, PC/AT, personal System/2 (PS/2), Apple Macintosh, and compatible users crisp text and vivid color graphics display when using the following graphics adapters : (VGA, 8514/A, Super VGA, VESA and XGA and Apple Macintosh Video Card). And so, this color monitor has a maximum horizontal resolution of 1280 dots and a maximum vertical resolution of 1024 lines for superior clarity of display. By accepting analog signal inputs which level is zero to 0.7 Volts. This color monitor can display and unlimited palette of colors depending on the graphics adapter and software being used.

Abbreviations
ADJ AFC CRT Def D.Y FBT H.SYNC OSC P.S.U PWA R.G.B V.Sync Adjustment Automatic Frequency Control Cathode Ray Tube Deflection Deflection Yoke Flyback Transformer Horizontal Synchronization Oscillator Power Supply Unit Printed Circuit Board Wiring Assembly Red, Green, Blue Vertical Synchronization

7

PIN CONNECTOR
Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Signal Red Green Blue GND GND GND - Red GND - Green GND - Blue Reserved GND - H.Sync GND Bi-directional Data (SDA) Horizontal Sync Vertical Sync (VCLK) Data Clock (SCL)

1 6 10 15
Arrangement of 15-pin D-sub connector

CAUTIONS FOR ADJUSTMENT AND REPAIR
· Degaussing is always required when adjusting purity or convergence. · The white balance adjustment has been done by a color analyzer in factory. The adjustment procedure, described in the service manual is made by a visual check. · Allow 20 minutes warm-up time for the display before checking or adjusting only electrical specification or function. · Reform the leadwire after any repair work.

Caution For Servicing
· In case of servicing or replacing CRT, high voltage sometimes remains in the anode of the CRT. Completely discharge high voltage before servicing or replacing CRT to prevent a shock to the serviceman.

8

OPERATION & ADJUSTMENT
ADJUSTMENT KEY

Launch OSD(On-Screen Display) menus

Select the next function

Increase the value of any selected function

Decrease the value of any selected function

9

ADJUSTMENT PROCESS

R G B

R G B

CONTRAST 50%

BRIGHTNESS 50%

R G B

R G B

PINCUSHION 50%

TRAPEZOID 50%

R G B

R G B

K

K

COLOR TEMP.
9300 6550

RED GAIN
50%

R G B

R G B

ZZ

Z

ZZ

Z

STATUS
H : +31.5KHZ V : +70.5 HZ

RECALL NO YES

When you choose the icon

on the OSD window, you can exit the OSD screen.

10

OSD(On-Screen Display) Menu 1
Adjust the contrast of image, the difference between light and dark areas on the screen. Range : 0-100%

CONTRAST 50%

BRIGHTNESS 50%

Adjust the brightness of the entire display.

H.POSITION 50%

Adjust the position of the display horizontally (left or right).

H.SIZE 50%

Adjust the display width (horizontal size).

V.POSITION 50%

Adjust the position of the display vertically (up or down).

V.SIZE 50%

Adjust the display height (vertical size).

Degauss the display and restore image quality.

11

OSD(On-Screen Display) Menu 2
Adjust the left and right margins for more convex or more concave margins. · Image turns to by . · Image turns to by - .
TRAPEZOID 50%

Adjust the trapezoid of the screen by moving the lines inward or outward. · Image turns to by . · Image turns to by - . Adjust parallelogram when the screen is leaning left or right. · Image turns to by . · Image turns to by - . Adjust the side balance when the sides of the screen are bowed towards left or right. · Image turns to by . · Image turns to by - . Adjust the vertical picture moire cancellation. · Image turns to by . - . · Image turns to by Adjust the rotation when the screen is tilted left or right(Optional). · Image turns to by . · Image turns to by - .

PARALLELOGRAM 50%

PIN BALANCE 50%

V. MOIRE 50%

ROTATION 50%

12

OSD(On-Screen Display) Menu 3
Choose different preset color temperatures or set your own customized color parameters.

RED GAIN 50%

Adjust the red gain.

GREEN GAIN 50%

Adjust the green gain.

BLUE GAIN 50%

Adjust the blue gain.

RED BIAS 50%

Adjust the red bias.

GREEN BIAS 50%

Adjust the green bias.

BLUE BIAS 50%

Adjust the blue bias.

OSD(On-Screen Display) Menu 4

STATUS
H : +31.5KHZ V : +70.5 HZ

Display horizontal & vertical frequency and polarity.

Reset the screen to the Factory Preset Display Settings.

YES : VESA DPMS operation. NO : NO DPMS operation.

Select language for OSD.

13

Self Diagnosis
When the monitor doesn't display, if you press any key, Self Diagnosis screen is displayed. Self Diagnosis function checks if the status of the monitor is No Signal or Out of range.

No Signal screen is displayed when the D-Sub signal connector is not connected or the status of the monitor is on DPMS mode.

Out of Range screen is displayed when the applied frequency is under or over normal range. Normal range H : 30-69 KHz V : 50-160 Hz

14

TROUBLESHOOTING HINTS
1. No Character

No Character

Are the Contrast & Brightness Controls maximum Yes

No

Change the Contrast & Brightness control to maximum

Is whole screen bright? Yes

No

No Raster

Refer to No Raster

Is CRT Cathode (Rk, Gk, Bk) signal level normal? No Is the output signal of the (pin 21, 24, 26) pre-amp (IC801, KA2500) normal? No

Yes Rk, Gk, Bk About 45Vpp

Check the peripheral circuit of CRT Board

Yes

Check the video output circuit and IC803 (pin 1, 3, 5) and their ambient circuit

Is 12V DC line normal? Yes Is clamping pulse (pin 18 of IC801) normal? Yes

No

Trouble in 12V DC line of the Main PWB

No

Check the clamping pulse circuit

Is input signal normal? Yes Trouble in IC801 and its ambient circuit

No

Check the signal cable

15

2. No Raster

No Raster

Is CRT heater red-hot? Yes Turn the Brightness & Contrast control to set Maximum Yes

No

Is Heater Voltage (CRT PWB) about 6V? Yes Trouble in power supply circuit

No

Trouble in CRT

Refer to trouble in power supply unit.

Is whole screen bright?

No

Trouble in power supply circuit

Yes Check G1 voltage about -40V? Yes Is CRT G2 (screen) voltage about 500V? Yes Is 80V DC line normal? Trouble in 80/ Refer to trouble 120V DC line of in P,S,U power supply unit

No

Trouble in G1 line of Main PWB

No

Trouble in FBT

No

Yes Does turning the Brightness control counterclockwise make screen bright? Yes Trouble in FBT

No

High Voltage trouble in FBT

16

3. A missing Color

One color is missing

Is input signal normal? 0.7Vpp Yes Is the output of pre-amp (IC801, KA2500) pin 21, 24, 26 all normal? Yes

No

Check video signal cable or video card.

No

Trouble in IC801 or its ambient circuit

CRT Cathode (Rk, Gk, Bk) is normal? Yes

No RK, GK, BK About 40V p-p

Is video output IC803 waveform normal? Yes

No

Trouble in video output circuit, IC803 or ambient

Each grid (G1, G2) voltage normal? Yes No Replace CRT

Trouble in 80/120V DC line

Trouble in 80/120V DC line

17

4. Abnormal OSD Font

Abnormal OSD Font

* If menu key selected.

Is menu key selected? Is OSD Font exist? Yes One color is missing Yes Is the output of IC802 (pin 13, 14, 15) normal?

No

Is Heater Voltage (CRT PWB) about 6V? Yes Troubie in IC802 or its ambient circuit

No

Trouble in Heater voltage line. Refer to trouble in P.S.U

No

Trouble in IC802 and its ambient circuit

Yes

Refer to Missing Color

18

5. Horizontal Output Circuit

Trouble in Horizontal output circuit (No Raster

Is the B+line voltage over 45V? Yes

No

Trouble in B+ Booster Circuit (Check the B+section of IC501, Check Q603 and its ambient circuit).

11V 0V

Is the H-out waveform of IC501 normal? Yes

No

Trouble in IC501

10V 0V

Is the Collector wave form of Q501 or Q502 normal? Yes

No

Trouble in Q501, Q502

Is the Collector waveform of Q503 normal? 66V Yes Trouble in Q504 and its ambient circuit.

No

Trouble in Q503 and its ambient circuit.

19

6. Unstable Picture 6-1. Horizontal

Unstable picture

Is H.Sync input pin of IC501 correct?

No

Check H.Sync Out of Micom or its ambient circuits.

Yes

Is the pin 3 of IC501 5V?

No

Check the value of C503, R502

Yes

Trouble in IC501

20

6-2. V.OSC/Deflection Circuit

Unstable or Abnormal picture

Is ± 13V DC line correct?

No

Trouble in power supply unit

Yes

45Vp-p

Is the output waveform of IC401 (pin 6) normal?

Yes

V.DY failure

No

Is the output pulse of IC501 (pin 23) normal?

Yes

Trouble in IC401 or its ambient circuit

No Trouble in V.Sync line or IC501 failure.

21

7. Focus

Monitor remains unfocused

Check Focus VR in FBT

Is focus acceptable?

Yes

OK

No Trouble in Focus circuit (FBT)

22

7-1. Dynamic Focus

FVH FVV
PHILIPS : 440V 180V NEC : 300V 120V SAMSUNG : 300V 120V DF
waveform

Focus is poor

* Check after adjusting the static focus finely by VR in FBT

FVH FVV

Is the waveform of the DF pin in FBT correct?

Yes

1. Check the CRT socket or connector wire 2. Trouble in FBT or CRT

No Is the cathode voltage of the D575 about 600V?

No

1. Check the waveform of the pin 3 of FBT. 2. Check D575

Yes Is the base voltage of the Q751 about 2.6V? Yes

No

1. Check the 12V DC line. 2. Check Q751,D755

Is the waveform of the pin 10 in IC501 DF correct? waveform
4.5V 2V 0V 0.8V

No

Trouble in IC501 or C520

Yes Trouble in Q752, Q753, Q754, D751, D752, D753, D754, Q755, Q756

23

8. Convergence

Poor convergence

Is convergence on the center area bad?

Yes

Adjust static convergence Refer to Adjustment procedure of convergence

No

Is convergence on the fringe area bad?

Yes

Adjust D.Y Location

24

9. Abnormal Picture 9-1. Horizontal Size

Abnormal H.Size

When the VR601 is changed, is the H.size changed?

No

Check pin 15 of IC501 and its ambient circuit (D604, R605, R606, R607)

Yes Is the H.Size about 295mm at VGAmode and Min. H.Size in OSD Menu?

No

1.Check B+ section of TDA9109 and its ambient circuit. 2.Check Q601 and its ambient circuit.

Yes It isn't out of order.

25

9-2. Vertical Size

Abnormal V.Size

Is changeable the DC voltage of IC401 pin 1?

No

Is the 3.5Vdc of pin 23 of the IC501?

Yes

Check the IC401 and its ambient circuit

Yes

No

Trouble V.OSC/ Deflection Circuit Refer to V.OSC/Deflection circuit

Check the IC501 and its ambient circuit

26

10. High Voltage Circuit
Trouble in H.V circuit (No Raster)

Is B+(45V) line voltage normal? Yes

No

Trouble in power supply circuit

Is Q574 base waveform normal? No

Yes

Trouble in Q574 or FBT

Is Q571 collector waveform normal? No

Yes

Trouble in Q572, Q573 12V Line

Is Q501 emitter waveform normal? No

Yes

Trouble in Q571

Is IC501 pin 26 waveform normal? No

Yes

Trouble in Q501, Q502

Is IC501 pin 29 voltage about 12V? Yes

No

Trouble in power supply

Is the input H.Sync correct? No Trouble in H.Sync

Yes

Trouble in IC501 ambient circuit.

27

11. Side-Pincushion Circuit

Side-Pincusion distortion is excessive or barrel

Select the side-pincushion icon on OSD menu, and adjust acceptable position.

Yes

O.K

No

Is the pin 24 waveform of IC501 correct No

Yes

Check IC501 or their ambient circuit (pin 14, 15, 16)

Is the waveform of IC501 pin 1, 2

Yes

Check IC501 or it's ambient circuit.

No Trouble in H.V Sync

28

12. Power Supply Unit (P.S.U)

Trouble in P.S.U

Is power switch on? Yes Is fuse F001 O.K? Yes Is the voltage of IC001 pin 3 16V? Yes Is voltage of T001 pin 6 130V (370V)? Yes Is the waveform of IC001 pin 1correct? 400Vpp (620Vpp) Yes Is voltage of C103 45V DC? Yes Is voltage of C101 80V DC? Yes Is voltage of C113 120V DC?

No

Switch on

No

Check the power cord outlet and diode D001, D002, D003, D004

No

Replace R004 Replace C005

No

Trouble in D001, D002, D003, D004, C004 and TH001.

No

Trouble in T001, IC001, IC101, PH001 and D005 etc.

No

Trouble in D102, D103 or B+ Part

No

Trouble in D101 or Video Part

No

Trouble in D108 or Video Part

A

29

A

Is voltage of C104 13V DC?

No

Trouble in D104, IC102 or horizontal Part.

Yes Is voltage of C105 -13V DC? Yes Is voltage of C106 8.7V DC? No Trouble in D106 or Q103 No

Trouble in D105 or vertical Part.

Yes P.S.U O.K

30

ALIGNMENT PROCEDURE
Standard Adjustment Conditions
1. Power source voltage : AC 120V, 60Hz./AC 220V, 50Hz 2. Aging : Take at least 20 minutes warm-up time. 3. Signals. Video : Analog 0.7Vpp 75 terminal positive polarity Synchronizing : TTL level Negative/Positive Separate/Composite Deflection frequency Horizontal Frequency : 30KHz - 69KHz Vertical Frequency : 50Hz - 160Hz

Pre-Adjustment
1. High voltage Adjustment Adjust 26 kvdc between Anode cap and ground at a cross hatch pattern of 31.5KHz by using VR551. 2. B+ Adjustment (H.min size) (a) Receive a cross hatch pattern of 31.5KHz (b) Set the H-Size control to the minimum. (c) Adjust H-Size to 295mm by using VR601

Main Adjustment
1. Setting the Controls Set the value of items as following. Contrast : Max. (OSD value up to 100) Brightness : Center (Set the OSD value to 50) 2. H.size, V.size, H.phase, V.position, Pincushion, Trapezoid Perceive the cross hatch pattern of Factory preset mode. H.Size, V.size, H.phase, V.position, Pincushion, Trapezoid are adjusted at each mode. In Factory, Auto Alignment was done at each mode. Therefore, Factory preset mode has it's own value according to each control. 3. Focus (a) Set brightness control to center and contrast control to MAX. (b) Receive all "H" character pattern of 60KHz mode signal. (c) Adjust the Focus control of FBT to obtain best Focus (static focus and Dynamic focus). 4. Geometric Distortion Adjustment. (a) Receive the cross hatch pattern of VGA mode signal by using the signal generator. (b) Pin balance, Parallelogram are adjusted the best geometric status. (c) Repeat the adjustment at each mode. 5. White Balance Adjustment (a) Receive a full white pattern of 60KHz mode. (b) Select 9300°K on the OSD Menu. (c) Set the bright control and contrast control to the maximum and receive the all black pattern. (d) Adjust the FBT screen VR to get the screen luminosity to 1 Ft/L. (e) Select the R, G, B Bias on the OSD menu and adjust the ADJUST +/ key to get the color coordinates in X=0.281, Y=0.311 (f) If the screen luminosity is changed adjust the sub brightness control to get the 1 Ft/L screen luminosity. (g) Set the brightness control to the center and contrast control to the maximum. (h) Receive a full white pattern. (i) Select the R, G, B gain on the OSD menu and adjust the ADJUST +/ key to get the color coordinates in X=0.281±0.03, Y=0.311±0.03 (j) Adjust the sub contrast control to get the screen luminosity to 34 Ft/L/ (k) Select 6550°K on the OSD menu and set the bright control and contrast control to the maximum and receive the all black pattern.

31

(l) Repeat (e),(f),(g),(h),(i),(j). Just a difference from 9300°K mode is color coordinates. Set color coordinates in X=0.313, Y=0.329 6. Static Convergence Adjustment (a) Apply an magenta cross hatch pattern on display. (b) Adjust the focus from the best over all focus on the display. Also adjust the brightness to the desired condition. (c) Vertical red and blue lines are converged by varying the angle between the two tabs of the 4-pole magnets. (d) Horizontal red and blue lines are converged by varying the tabs together, keeping the angle between them constant. (e) Apply a white cross hatch pattern on display. (f) Vertical green and magenta lines are converged by varying the the angle between the two tabs of the 6-pole magnets. (g) Horizontal green and magenta lines are converged by varying the tabs together, keeping the angle between them constant.

32

BLOCK DIAGRAM

(R.G.B)

R G B
OSD IC
LSC4525P2 OSD (R.G.B)

VIDEO OUTPUT LM2407T

VIDEO PREAMP KA2500

BIAS CONTROL H.V SCL SDA H.VTG

SCREEN, FOCUS

H V
SCL SDA

BIAS(R.G.B)

MICOM
SDA SCL 68HC705BD32 TILT IC L272M EEPROM 24C08B V.DRV AMP KA2142 V.DY

33
FBT H.OSC. & V.DRV TDA9109 120V,80V,45V 12V, 12V CF1147DW2300 H.V SDA SCL

L
GND FILTER SMPS CONTROL KA2S0880 B+ CONTROL SMPS TRANS H.DRV H.DY

N

H.VTG B+ CONTROL KA7500B

PCB LAYOUT
Main PCB Component Side

34

Main PCB Solder Side

35

Video PCB Component Side

Video PCB Solder Side

36

EXPLODED VIEW DIAGRAM

38

REPLACEMENT PARTS LIST
Important Safety Notice
Components identified with the International Symbol have special characteristics important for safety. When replacing any components, use only manufacturer's specified parts.

Abbreviation of Description
RESISTOR Description Allowance F ± 1% J ± 5% K ± 10% M ± 20% G ± 2% Example: Fig & Index R101 Part No Description

Resistors RE-42820J Cabron: 82J

CAPACITOR Description C D F J K P Z Allowance ± 0.25pF ± 0.5% ± 1pF ± 5% ± 10% ± 100% ~ 0% ± 80% ~

Example: Fig & Index C102 C105 C402 Part No Description

Capacitors CCXF1H104Z Ceramic 50V Z CBSLH200J Ceramic 50V J CCXB1H331K Ceramic 50V K

39

CIRCUIT BOARD ELECTRICAL PARTS LIST
The components identified by mark have special characteristics important for safety and x-ray radiation. These should be replaced only with the types specified in the parts list. LOC 10010 CT801 CT802 DG001 20010 CA801 CA802 CN001 C001 C004 C006 C103 C402 C406 C409 C519 C553 C578 DL001 D102 D103 D104 F001 IC001 IC102 IC103 IC201 IC401 IC501 IC801 L001 L501 L502 L571 L601 PH001 P001 Q503 PART-CODE PCFMCAJ046 9979617018 9970710176 5MG0000062 PCMPM1J046 99707A0016 9970770019 9970700123 CL1UC3224M CEYP2G221Z CCYB3A103K CEXF2A471V CMXL2A474J CEXF1C471V CMXM2A224J CMYH3D532J CMXF2D824J CMXM2A224J DLT2462A2D DS3L60---DS3L60---DS3L60---5F3CB3122L 1KA2S08801KA78R12-1K1A7805P1 1DWM209T-1KA2142--1TDA9109-1KA2500--5PDLF30555MH0000051 5MC0000069 5MC0000068 5MC0000065 1TLP721GR9979500014 TKSC3502EPART-NAME COVER FRONT AS CDT CRT GND AS COIL DEGAUSSING PCB MAIN MANUAL AS CONN AS CONN AS CONN AS C LINE ACROSS C ELECTRO C CERA C ELECTRO C MYLAR C ELECTRO C MYLAR C MYLAR C MYLAR C MYLAR LED DIODE DIODE DIODE FUSE CERA IC POWER IC REGULATOR IC REGULATOR IC MICOM IC V-OUT IC H.OSC IC FILTER LINE COIL H-LINEARITY COIL CHOKE COIL CHOKE COIL CHOKE IC PHOTO COUPLER RECEPTACLE TR PART-DESC CMC-710B M41QAR361X124(E) 0.12*5*24+BL102NG=730 DG-710B CMC-710B SMH250-10+1007#24#28=160 SMH250-07+1007#24=220 4.3+35404-9002+1015#18=50 0.22MF 1J(UCVSNDF/SV)+Q/O 400V SMH 220MF (25.4*40) 1KV B 0.01MF K 100V RSS 470MF 16*31.5 MEU 100V 0.47MF J 16V RSS 470MF (10X12.5)TP 100V 0.22MF J 2KV BUP 5300PF J BULK MPP 200V 0.82MF J 100V 0.22MF J LT2462-A2-D51 S3L60 S3L60 S3L60 SEMKO TL 3.15A 250V MF51 KA2S0880 KA78R12 KIA7805PI 68HC705BD32 KA2142 TDA9109 KA2500 DLF-3055L TRL-195A 33UH K BULK(14*16) CH-85A CH-85 TLP721D4GR YA03P/FILTER EMI KSC3502E

40

LOC D504 Q504 Q574 Q551 Q552 Q555 Q577 Q603 RL001 RL501 R754 SG900 SW001 S001 TH001 T001 T002 T501 T571 T601 30010 C015 C117 C119 C120 C122 C203 C204 C205 C206 C212 C403 C502 C503 C506 C507 C520 C532 C549 C581

PART-CODE DDTV32F--T2SC5387-TKSC5386-T1RF630ATS T1RF630ATS T1RF630ATS T2SK2799-T2SK2799-5SC0201103 5SC0101031 RS01Z104J4SG0D00104 5S50101Z01 9970800015 DTP8D15--5RM0000090 5RY0000002 5RD0000037 5RH0000105 5RF0000003 PCMPJ1J046 HCFK104ZCA HCFK104ZCA HCQK101JCA HCQK101JCA HCFK104ZCA HCFK104ZCA HCFK104ZCA HCQK360JCA HCQK360JCA HCQK181JCA HCFK104ZCA HCBK223KCA HCQK102JCA HCFK333ZCA HCFK224ZCA HCQK102JCA HCFK104ZCA HCQK181JCA HCFK104ZCA

PART-NAME DIODE TR H.OUT TR FET FET FET FET FET SW RELAY SW RELAY R M-OXIDE FILM SPARK GAP SW TACT CABLE SIGNAL AS THERMISTOR TRANS SMPS TRANS SYNC TRANS DRIVE FBT TRANS DUMMY PCB SMD AS C CHIP CERA C CHIP CERA C CHIP CERA C CHIP CERA C CHIP CERA C CHIP CERA C CHIP CERA C CHIP CERA C CHIP CERA C CHIP CERA C CHIP CERA C CHIP CERA C CHIP CERA C CHIP CERA C CHIP CERA C CHIP CERA C CHIP CERA C CHIP CERA C CHIP CERA

PART-DESC DTV32F 2SC5387 KSC5386 IRF630A-TSTU IRF630A-TSTU IRF630A-TSTU 2SK2799 2SK2799 HR-CR323 2C-1P DC12V HR-703V DC12V 1C-1P 1W 100K OHM J (TAPPING) S-23 1.5KV KPT-1115VM 1C-1P 15P+2C/DDC=1.5M (IVY) TP8D15 DWT-44A1 DST-603 DDT-710B CF1147DW2300 TDH-710B CMC-710B 50V Y5V 0.1MF Z 2012 50V Y5V 0.1MF Z 2012 50V CH 100PF J 2012 50V CH 100PF J 2012 50V Y5V 0.1MF Z 2012 50V Y5V 0.1MF Z 2012 50V Y5V 0.1MF Z 2012 50V CH 36PF J 2012 50V CH 36PF J 2012 50V CH 180PF J 2012 50V Y5V 0.1MF Z 2012 50V X7R 0.022MF K 2012 50V CH 1000PF J 2012 Y5V 50V 0.033MF Z 2012 Y5V 50V 0.22MF Z 2012 50V CH 1000PF J 2012 50V Y5V 0.1MF Z 2012 50V CH 180PF J 2012 50V Y5V 0.1MF Z 2012

41

LOC C802 C803 C812 C813 C814 C815 C832 C833 C862 C863 C878 C879 C881 C882 C883 C884 C885 R117 R205 R208 R209 R210 R216 R217 R218 R228 R234 R235 R238 R246 R247 R248 R252 R272 R284 R285 R286 R289 R502 R505

PART-CODE HCFK104ZCA HCFK104ZCA HCFK104ZCA HCFK104ZCA HCQK101JCA HCQK101JCA HCFK104ZCA HCFK104ZCA HCFK104ZCA HCFK104ZCA HCQK122JCA HCQK122JCA HCFK103ZCA HCFK103ZCA HCFK103ZCA HCQK220JCA HCQK220JCA HRFT272JCA HRFT472JCA HRFT000JCA HRFT472JCA HRFT472JCA HRFT151JCA HRFT201JCA HRFT472JCA HRFT222JCA HRFT101JCA HRFT101JCA HRFT472JCA HRFT472JCA HRFT472JCA HRFT472JCA HRFT472JCA HRFT563JCA HRFT912JCA HRFT912JCA HRFT912JCA HRFT202JCA HRFT682JCA HRFT472JCA

PART-NAME C CHIP CERA C CHIP CERA C CHIP CERA C CHIP CERA C CHIP CERA C CHIP CERA C CHIP CERA C CHIP CERA C CHIP CERA C CHIP CERA C CHIP CERA C CHIP CERA C CHIP CERA C CHIP CERA C CHIP CERA C CHIP CERA C CHIP CERA R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP

PART-DESC 50V Y5V 0.1MF Z 2012 50V Y5V 0.1MF Z 2012 50V Y5V 0.1MF Z 2012 50V Y5V 0.1MF Z 2012 50V CH 100PF J 2012 50V CH 100PF J 2012 50V Y5V 0.1MF Z 2012 50V Y5V 0.1MF Z 2012 50V Y5V 0.1MF Z 2012 50V Y5V 0.1MF Z 2012 50V CH 1200PF J 2012 50V CH 1200PF J 2012 50V Y5V 0.01MF Z 2012 50V Y5V 0.01MF Z 2012 50V Y5V 0.01MF Z 2012 50V CH 22PF J 2012 50V CH 22PF J 2012 1/10 2.7K OHM J 2012 1/10 4.7K OHM J 2012 1/10 0 OHM J 2012 1/10 4.7K OHM J 2012 1/10 4.7K OHM J 2012 1/10 150 OHM J 2012 1/10 200 OHM J 2012 1/10 4.7K OHM J 2012 1/10 2.2K OHM J 2012 1/10 100 OHM J 2012 1/10 100 OHM J 2012 1/10 4.7K OHM J 2012 1/10 4.7K OHM J 2012 1/10 4.7K OHM J 2012 1/10 4.7K OHM J 2012 1/10 4.7K OHM J 2012 1/10 56K OHM J 2012 1/10 9.1K OHM J 2012 1/10 9.1K OHM J 2012 1/10 9.1K OHM J 2012 1/10 2K OHM J 2012 1/10 6.8K OHM J 2012 1/10 4.7K OHM J 2012

42

LOC R506 R508 R513 R515 R516 R517 R531 R576 R581 R753 R801 R831 R853 R856 R861 R880 R885 R886 R887 R888 R889 R890 R936 R938 R942 40010 CW201 CW202 C002 C003 C008 C010 C101 C102 C104 C106 C113 C116 C522 C523

PART-CODE HRFT272JCA HRFT472JCA HRFT153JCA HRFT105JCA HRFT122JCA HRFT103JCA HRFT103JCA HRFT223JCA HRFT752JCA HRFT621JCA HRFT750JCA HRFT750JCA HRFT472JCA HRFT472JCA HRFT750JCA HRFT101JCA HRFT562JCA HRFT105JCA HRFT561JCA HRFT182JCA HRFT101JCA HRFT472JCA HRFT244JCA HRFT243JCA HRFT562JCA PCMPJ0J046 485923282S 485923272S CH1FDF222M CH1FDF222M CH1FDF222M CH1FDF222M CEXF2A470V CCXB3D102K CEXF1E471V CEXF1C471V CEXF2C470V CCXB3D222K CMXF2G184J CMXF2G154J

PART-NAME R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP PCB MAIN ODD SHAPE AS CONN WAFER CONN WAFER C CERA AC C CERA AC C CERA AC C CERA AC C ELECTRO C CERA C ELECTRO C ELECTRO C ELECTRO C CERA C MYLAR C MYLAR

PART-DESC 1/10 2.7K OHM J 2012 1/10 4.7K OHM J 2012 1/10 15K OHM J 2012 1/10 1M OHM J 2012 1/10 1.2K OHM J 2012 1/10 10K OHM J 2012 1/10 10K OHM J 2012 1/10 22K OHM J 2012 1/10 7.5K OHM J 2012 1/10 620 OHM J 2012 1/10 75 OHM J 2012 1/10 75 OHM J 2012 1/10 4.7K OHM J 2012 1/10 4.7K OHM J 2012 1/10 75 OHM J 2012 1/10 100 OHM J 2012 1/10 5.6K OHM J 2012 1/10 1M OHM J 2012 1/10 560 OHM J 2012 1/10 1.8K OHM J 2012 1/10 100 OHM J 2012 1/10 4.7K OHM J 2012 1/10 240K OHM J 2012 1/10 24K OHM J 2012 1/10 5.6K OHM J 2012 CMC-710B 5267-07A STICK TYPE 5267-06A STICK TYPE HIKB AC400V 222M HIKB AC400V 222M HIKB AC400V 222M HIKB AC400V 222M 100V RSS 47MF (10X16) TP 2KV B 1000PF K (TAPPING) 25V RSS 470MF (10X16) TP 16V RSS 470MF (10X12.5)TP 160V RSS 47MF (13X25) TP HIKB 2KV 2200PF K MPP 400V 0.18MF J MPP 400V 0.15MF J

43

LOC C531 C551 C552 C555 C574 C582 C584 C587 C588 C592 C605 C902 D001 D002 D003 D004 D005 D006 D101 D105 D106 D108 D403 D511 D512 D573 D575 D576 D577 D602 D603 D913 D914 IC203 IC502 IC802 IC804 PR001 P002 P003

PART-CODE CEXF1C102V CMXF2D204J CMXF2D184J CMXF2D334J CMXH3C102J CEXF2A221V CMXF2D564J CEXF2G220D CEXF2G220D CEXF2C220V CMXF2D474J CMXF2D104J D2A05----D2A05----D2A05----D2A05----D1N4937GPDHER107--DRU1P----DHER107--DHER107--DRU1P----D1N4002A-DTVR1G---DTVR1G---DS2L60---R DRU1P----DTVR1G---DTVR1G---DTVR1G---DS2L60---R DHER107--DHER107--1M24C08BN6 1KA7500B-1LSC4525P2 1LM358N--DECPAC140M 9977410800 9977410800

PART-NAME C ELECTRO C MYLAR C MYLAR C MYLAR C MYLAR C ELECTRO C MYLAR C ELECTRO C ELECTRO C ELECTRO C MYLAR C MYLAR DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE IC EEPROM IC IC OSD IC OP AMP POSISTOR TERMINAL PIN TERMINAL PIN

PART-DESC 16V RSS 1000MF (10X20) TP MPP 200V 0.2MF J (TP) MPP 200V 0.18MF J (TP) 200V MPP 0.33MF J (TP) 1.6KV BUP 1000PF J 100V RSS 220MF (16X25) TP MPP 200V 0.56MF J 400V KMG 22MF(12.5*25) TP 400V KMG 22MF(12.5*25) TP 160V RSS 22MF (10X20) TP MPP 200V 0.47MF J MPP 200V 0.1MF J 2A05 2A05 2A05 2A05 1N4937GP (TAPPING) HER107 RU 1P (TAPPING) HER107 HER107 RU 1P (TAPPING) 1N4002 TVR1G TPA1 TVR1G TPA1 S2L60 RU 1P (TAPPING) TVR1G TPA1 TVR1G TPA1 TVR1G TPA1 S2L60 HER107 HER107 M24C08BN6 KA7500B LSC4525P2 LM358N ECPAC140M290 BSP1(SN) L=15MM BSP1(SN) L=15MM

44

LOC P401 P402 P403 P501 P502 P503 P504 R004 R006 R007 R107 R109 R110 R118 R407 R408 R518 R520 R529 R532 R554 R573 R587 R589 R603 R604 R631 R632 R633 R755 R756 R757 SW201 SW202 SW203 SW204 VR551 VR601 50010 C005

PART-CODE 9977410800 9977410800 9977410800 9977410800 9977410800 9977410800 9977410800 RS02Z513JRS01Z683JRS01Z683JRS02Z392JRS02Z369JRS02Z399JRS02Z100JRS01Z109JRS02Z479JRS01Z101JRS01Z159JRS01Z159JRS01Z101JRS01Z471JRS01Z470JRS02Z102JRW01Z308JN RS02Z331JRW01Z308JN RS02Z129JRS02Z129JRS02Z129JRS01Z104JRS01Z104JRS01Z104J5S50101Z01 5S50101Z01 5S50101Z01 5S50101Z01 RV6421503P RV6121202P PCMPJRJ046 CEXF1H101V

PART-NAME TERMINAL PIN TERMINAL PIN TERMINAL PIN TERMINAL PIN TERMINAL PIN TERMINAL PIN TERMINAL PIN R M-OXIDE FILM R M-OXIDE FILM R M-OXIDE FILM R M-OXIDE FILM R M-OXIDE FILM R M-OXIDE FILM R M-OXIDE FILM R M-OXIDE FILM R M-OXIDE FILM R M-OXIDE FILM R M-OXIDE FILM R M-OXIDE FILM R M-OXIDE FILM R M-OXIDE FILM R M-OXIDE FILM R M-OXIDE FILM R WIRE WOUND R M-OXIDE FILM R WIRE WOUND R M-OXIDE FILM R M-OXIDE FILM R M-OXIDE FILM R M-OXIDE FILM R M-OXIDE FILM R M-OXIDE FILM SW TACT SW TACT SW TACT SW TACT R SEMI FIXED R SEMI FIXED PCB MAIN RADIAL AS C ELECTRO

PART-DESC BSP1(SN) L=15MM BSP1(SN) L=15MM BSP1(SN) L=15MM BSP1(SN) L=15MM BSP1(SN) L=15MM BSP1(SN) L=15MM BSP1(SN) L=15MM 2W 51K OHM J 1W 68K OHM J (TAPPING) 1W 68K OHM J (TAPPING) 2W 3.9K OHM J (TAPPING) 2W 3.6 OHM J (TAPPING) 2W 3.9 OHM J 2W 10 OHM J (TAPPING) 1W 1 OHM J (TAPPING) 2W 4.7 OHM J (TAPPING) 1W 100 OHM J (TAPPING) 1W 1.5 OHM J (TAPPING) 1W 1.5 OHM J (TAPPING) 1W 100 OHM J (TAPPING) 1W 470 OHM J (TAPPING) 1W 47 OHM J (TAPPING) 2W 1K OHM J (TAPPING) 1W 0.30 OHM J NON-INDUCT 2W 330 OHM J TAPPING 1W 0.30 OHM J NON-INDUCT 2W 1.2 OHM J (TAPPING) 2W 1.2 OHM J (TAPPING) 2W 1.2 OHM J (TAPPING) 1W 100K OHM J (TAPPING) 1W 100K OHM J (TAPPING) 1W 100K OHM J (TAPPING) KPT-1115VM 1C-1P KPT-1115VM 1C-1P KPT-1115VM 1C-1P KPT-1115VM 1C-1P CCT 065AT 50K OHM B TAP CCT 063BT 2K OHM B TAP CMC-710B 50V RSS 100MF (8X11.5) TP

45

LOC C011 C013 C014 C105 C107 C108 C109 C110 C111 C112 C114 C118 C202 C209 C210 C211 C266 C267 C271 C276 C277 C278 C279 C281 C401 C404 C405 C407 C408 C410 C411 C417 C504 C505 C509 C510 C511 C512 C513 C514

PART-CODE CEXF1H109V CEXF1H109V CCXF1H223Z CEXF1C101V CCXF1H223Z CEXF1C101V CEXF1C101V CEXF1C221V CEXF1H100V CMXM2A104J CEXF1C101V CCXB2H102K CEXF1C101V CCXB1H221K CCXB1H221K CEXF1H100V CMXM2A104J CEXD1H220F CEXF1H100V CEXF1H100V CEXF1H100V CEXF1H100V CEXF1H100V CEXF1H100V CMX12A154J CEXF1E470V CEXF1C221V CEXF1H101V CCXB1H471K CCXF1H104Z CMXM2A562J CCXF1H104Z CMXM2A182J CEXF1H479V CCXF1H104Z CEXF1E470V CCXB1H102K CEXF1H339V CMXM2A392J CEXF1H109V

PART-NAME C ELECTRO C ELECTRO C CERA C ELECTRO C CERA C ELECTRO C ELECTRO C ELECTRO C ELECTRO C MYLAR C ELECTRO C CERA C ELECTRO C CERA C CERA C ELECTRO C MYLAR C ELECTRO C ELECTRO C ELECTRO C ELECTRO C ELECTRO C ELECTRO C ELECTRO C MYLAR C ELECTRO C ELECTRO C ELECTRO C CERA C CERA C MYLAR C CERA C MYLAR C ELECTRO C CERA C ELECTRO C CERA C ELECTRO C MYLAR C ELECTRO

PART-DESC 50V RSS 1MF (5X11) TP 50V RSS 1MF (5X11) TP 50V F 0.022MF Z (TAPPING) 16V RSS 100MF (6.3X11) TP 50V F 0.022MF Z (TAPPING) 16V RSS 100MF (6.3X11) TP 16V RSS 100MF (6.3X11) TP 16V RSS 220MF (8X11.5) TP 50V RSS 10MF (5X11) TP 100V 0.1MF J (TP) 16V RSS 100MF (6.3X11) TP 500V B 1000PF K (TAPPING) 16V RSS 100MF (6.3X11) TP 50V B 220PF K (TAPPING) 50V B 220PF K (TAPPING) 50V RSS 10MF (5X11) TP 100V 0.1MF J (TP) 50V RND 22MF (10*11.5) 50V RSS 10MF (5X11) TP 50V RSS 10MF (5X11) TP 50V RSS 10MF (5X11) TP 50V RSS 10MF (5X11) TP 50V RSS 10MF (5X11) TP 50V RSS 10MF (5X11) TP MEU 100V 0.15MF J(TP) 25V RSS 47MF (5X11) TP 16V RSS 220MF (8X11.5) TP 50V RSS 100MF (8X11.5) TP 50V B 470PF K (TAPPING) 50V F 0.1MF Z 100V 5600PF J (TP) 50V F 0.1MF Z 100V 1800PF J (TP) 50V RSS 4.7MF (5X11) TP 50V F 0.1MF Z 25V RSS 47MF (5X11) TP 50V B 1000PF K (TAPPING) 50V RSS 3.3MF (5X11) TP 100V 3900PF J (TP) 50V RSS 1MF (5X11) TP

46

LOC C515 C516 C517 C518 C525 C528 C533 C554 C556 C570 C572 C573 C577 C579 C580 C583 C586 C591 C593 C601 C603 C606 C751 C801 C804 C808 C811 C831 C861 C880 C901 C996 C998 F001A F001B IC101 IC202 Q102 Q103 Q104

PART-CODE CMXM2A104J CCXF1H104Z CEXF2A100V CMXM2A104J CEXF1H100V CEXF1H229V CEXF1C101V CCXB2H102K CMXM2A104J CEXF1H100V CEXF1C221V CEXF1C101V CMXM2A562J CEXF1C470V CEXF1C101V CCXB2H471K CEXF1H100V CMXM2A104J CEXF1H339V CEXF1H109V CCXB2H102K CMXM2A473J CEXF1H100V CEXF1H100V CEXF1C470V CEXF1C470V CEXF1C220V CEXF1H100V CEXF1H100V CEXF1H101V CMXM2A473J CEXF1C220V CEXF1H100V 9977410900 9977410900 1KA431ZTA1KA7542--TKSD471ACY TKTA1273YTZSR1006--

PART-NAME C MYLAR C CERA C ELECTRO C MYLAR C ELECTRO C ELECTRO C ELECTRO C CERA C MYLAR C ELECTRO C ELECTRO C ELECTRO C MYLAR C ELECTRO C ELECTRO C CERA C ELECTRO C MYLAR C ELECTRO C ELECTRO C CERA C MYLAR C ELECTRO C ELECTRO C ELECTRO C ELECTRO C ELECTRO C ELECTRO C ELECTRO C ELECTRO C MYLAR C ELECTRO C ELECTRO FUSE CLIP FUSE CLIP IC SHUNT IC VOTAGE DETECTOR TR TR TR

PART-DESC 100V 0.1MF J (TP) 50V F 0.1MF Z 100V RSS 10MF (6.3X11) TP 100V 0.1MF J (TP) 50V RSS 10MF (5X11) TP 50V RSS 2.2MF (5X11) TP 16V RSS 100MF (6.3X11) TP 500V B 1000PF K (TAPPING) 100V 0.1MF J (TP) 50V RSS 10MF (5X11) TP 16V RSS 220MF (8X11.5) TP 16V RSS 100MF (6.3X11) TP 100V 5600PF J (TP) 16V RSS 47MF (5X11) TP 16V RSS 100MF (6.3X11) TP 500V B 470PF K (TAPPING) 50V RSS 10MF (5X11) TP 100V 0.1MF J (TP) 50V RSS 3.3MF (5X11) TP 50V RSS 1MF (5X11) TP 500V B 1000PF K (TAPPING) 100V 0.047MF J (TP) 50V RSS 10MF (5X11) TP 50V RSS 10MF (5X11) TP 16V RSS 47MF (5X11) TP 16V RSS 47MF (5X11) TP RSS 16V 22MF 5*11 50V RSS 10MF (5X11) TP 50V RSS 10MF (5X11) TP 50V RSS 100MF (8X11.5) TP 100V 0.047MF J (TP) RSS 16V 22MF 5*11 50V RSS 10MF (5X11) TP BSP3-H T0.4 SN 5.2 BSP3-H T0.4 SN 5.2 KA431ZTA KA7542 KSD471ACY KTA1273-Y KSR1006 (AUTO)

47

LOC Q201 Q202 Q203 Q204 Q501 Q502 Q516 Q517 Q525 Q553 Q556 Q557 Q558 Q571 Q572 Q573 Q575 Q601 Q602 Q751 Q752 Q753 Q754 Q755 Q756 Q871 Q901 Q902 Q903 Q904 Q905 X201 60010 A0001 B001 B002 B101 B175 B345 B381

PART-CODE TKSD471ACY TKSD471ACY TZSR1006-TZSR1006-TKSD471ACY TKSA539CYTKSA539CYTZSR1006-TZTA1270YTZSR1006-TZSR1006-TZSR1006-TZSR1006-T2N3904--TKSD471ACY TKSA539CYTKSD471ACY TKSA539CYTKSD471ACY TKSP45---TKSP92---TKSP92---TKSP45---TKSP45---TKSP45---TZSR1006-TKSA910Y-TZSC945CYTKSD471ACY TKSA539CYTZSR1009-5XJ6R0000E PCMPJAJ046 9979800462 5PB13857-5PB13857-5PB13857-5PB13857-5PB13857-5PB13857--

PART-NAME TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR TR CRYSTAL QUARTZ PCB MAIN AXIAL AS PCB MAIN COIL BEAD COIL BEAD COIL BEAD COIL BEAD COIL BEAD COIL BEAD

PART-DESC KSD471ACY KSD471ACY KSR1006 (AUTO) KSR1006 (AUTO) KSD471ACY KSA539CY KSA539CY KSR1006 (AUTO) KTA1270Y(AUTO)(562Y) KSR1006 (AUTO) KSR1006 (AUTO) KSR1006 (AUTO) KSR1006 (AUTO) 2N3904 KSD471ACY KSA539CY KSD471ACY KSA539CY KSD471ACY KSP45 KSP92 KSP92 KSP45 KSP45 KSP45 KSR1006 (AUTO) KSA910Y KSC945C-Y (AUTO) KSD471ACY KSA539CY KSR1009 HC-49/S 6MHZ 22PF 30PPM CMC-710B T1.6*330*246 BI3857(AXIAL) BI3857(AXIAL) BI3857(AXIAL) BI3857(AXIAL) BI3857(AXIAL) BI3857(AXIAL)

48

LOC B881 C009 C201 C207 C208 C214 C246 C501 C524 C534 C548 C571 C575 C576 C752 C903 C941 C994 C995 C997 C999 DZ001 DZ008 DZ201 DZ202 DZ203 DZ401 DZ501 DZ571 DZ581 D012 D107 D206 D207 D209 D503 D525 D531 D532 D571

PART-CODE 5PB13857-CCZB1H102K CCZB1H181K CCZB1H221K CCZB1H221K CCZF1H104Z CCZF1H104Z CCZB1H101K CCZB1H471K CCZF1H104Z CCZB1H181K CCZB1H471K CCZB1H103K CCZB1H102K CCZF1H104Z CCZB1H103K CCZB1H102K CCZF1H104Z CCZF1H104Z CCZB1H152K CCZF1H104Z DDZ4R3BM-DDZ8R2BM-DDZ5R1B--DDZ5R1B--DDZ5R1B--DDZ5R1B--DDZ5R1B--DDZ5R1B--DDZ15BM--DZN4148--DZN4148--DZN4148--DZN4148--DZN4148--DZN4148--DZN4148--DZN4148--DZN4148--DZN4148---

PART-NAME COIL BEAD C CERA C CERA C CERA C CERA C CERA C CERA C CERA C CERA C CERA C CERA C CERA C CERA C CERA C CERA C CERA C CERA C CERA C CERA C CERA C CERA DIODE ZENER DIODE ZENER DIODE ZENER DIODE ZENER DIODE ZENER DIODE ZENER DIODE ZENER DIODE ZENER DIODE ZENER DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE

PART-DESC BI3857(AXIAL) 50V B 1000PF K 50V B 180PF K 50V B 220PF K 50V B 220PF K 50V HIKF 0.1MF Z 50V HIKF 0.1MF Z 50V B 100PF K 50V B 470PF K 50V HIKF 0.1MF Z 50V B 180PF K 50V B 470PF K HIKB 50V 0.01MF K AXIAL 50V B 1000PF K 50V HIKF 0.1MF Z HIKB 50V 0.01MF K AXIAL 50V B 1000PF K 50V HIKF 0.1MF Z 50V HIKF 0.1MF Z 50V B 1500PF K (AXIAL) 50V HIKF 0.1MF Z DZ4.3BM DZ8.2BM DZ-5.1B DZ-5.1B DZ-5.1B DZ-5.1B DZ-5.1B DZ-5.1B DZ15BM 1N4148 AUTO 52MM 1N4148 AUTO 52MM 1N4148 AUTO 52MM 1N4148 AUTO 52MM 1N4148 AUTO 52MM 1N4148 AUTO 52MM 1N4148 AUTO 52MM 1N4148 AUTO 52MM 1N4148 AUTO 52MM 1N4148 AUTO 52MM

49

LOC D572 D574 D578 D601 D604 D751 D752 D753 D754 D755 D756 D757 D801 D802 D831 D832 D861 D862 D901 D902 D912 J411 L881 R001 R010 R102 R105 R106 R108 R111 R112 R113 R115 R116 R201 R202 R203 R204 R207 R211

PART-CODE DZN4148--DZN4148--DFDH400--DZN4148--DZN4148--DZN4148--DZN4148--DZN4148--DZN4148--DZN4148--DZN4148--DZN4148--DZN4148--DZN4148--DZN4148--DZN4148--DZN4148--DZN4148--DZN4148--DZN4148--DZN4148--RD-AZ101J5CPZ101K02 RD-2Z105JRD-4Z101JRD-4Z201JRD-AZ222JRD-AZ511JRN-AZ2102F RD-AZ102JRD-AZ153JRD-AZ102JRN-AZ1211F RD-AZ472JRD-AZ333JRD-AZ472JRD-AZ911JRD-AZ122JRD-AZ472JRN-AZ1212F

PART-NAME DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE R CARBON FILM COIL PEAKING R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R METAL FILM R CARBON FILM R CARBON FILM R CARBON FILM R METAL FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R METAL FILM

PART-DESC 1N4148 AUTO 52MM 1N4148 AUTO 52MM FDH400 1N4148 AUTO 52MM 1N4148 AUTO 52MM 1N4148 AUTO 52MM 1N4148 AUTO 52MM 1N4148 AUTO 52MM 1N4148 AUTO 52MM 1N4148 AUTO 52MM 1N4148 AUTO 52MM 1N4148 AUTO 52MM 1N4148 AUTO 52MM 1N4148 AUTO 52MM 1N4148 AUTO 52MM 1N4148 AUTO 52MM 1N4148 AUTO 52MM 1N4148 AUTO 52MM 1N4148 AUTO 52MM 1N4148 AUTO 52MM 1N4148 AUTO 52MM 1/6 100 OHM J 100UH K (AXIAL 3.5MM) 1/2 1M OHM J 1/4 100 OHM J 1/4 200 OHM J 1/6 2.2K OHM J 1/6 510 OHM J 1/6 21K OHM F 1/6 1K OHM J 1/6 15K OHM J 1/6 1K OHM J 1/6 1.21K OHM F 1/6 4.7K OHM J 1/6 33K OHM J 1/6 4.7K OHM J 1/6 910 OHM J 1/6 1.2K OHM J 1/6 4.7K OHM J 1/6 12.1K OHM F

50

LOC R212 R213 R214 R215 R226 R227 R229 R230 R231 R232 R241 R249 R250 R281 R282 R283 R293 R294 R295 R296 R401 R402 R403 R405 R406 R410 R411 R412 R501 R503 R504 R507 R509 R510 R511 R512 R514 R519 R521

PART-CODE RN-AZ9091F RN-AZ8252F RN-AZ1502F RN-AZ3012F RD-AZ101JRD-AZ101JRD-AZ222JRD-AZ222JRD-AZ222JRD-AZ750JRD-AZ472JRD-AZ101JRD-AZ101JRD-AZ472JRD-AZ472JRD-AZ472JRD-AZ122JRD-AZ563JRD-AZ331JRD-AZ331JRD-AZ102JRD-AZ103JRN-AZ1002F RN-AZ2211F RN-4Z4000F RN-AZ5601F RD-2Z229JRD-2Z209JRD-AZ102JRD-AZ182JRD-AZ122JRD-AZ102JRD-AZ361JRD-AZ183JRD-AZ333JRD-AZ474JRD-AZ563JRD-AZ472JRD-4Z200J-

PART-NAME R METAL FILM R METAL FILM R METAL FILM R METAL FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R METAL FILM R METAL FILM R METAL FILM R METAL FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM

PART-DESC 1/6 9.09K OHM F 1/6 82.5K OHM F 1/6 15K OHM F 1/6 30.1K OHM F 1/6 100 OHM J 1/6 100 OHM J 1/6 2.2K OHM J 1/6 2.2K OHM J 1/6 2.2K OHM J 1/6 75 OHM J 1/6 4.7K OHM J 1/6 100 OHM J 1/6 100 OHM J 1/6 4.7K OHM J 1/6 4.7K OHM J 1/6 4.7K OHM J 1/6 1.2K OHM J 1/6 56K OHM J 1/6 330 OHM J 1/6 330 OHM J 1/6 1K OHM J 1/6 10K OHM J 1/6 10K OHM F 1/6 2.21K OHM F 1/4W 400 OHM F 1/6 5.6K OHM F 1/2 2.2 OHM J 1/2 2 OHM J 1/6 1K OHM J 1/6 1.8K OHM J 1/6 1.2K OHM J 1/6 1K OHM J 1/6 360 OHM J 1/6 18K OHM J 1/6 33K OHM J 1/6 470K OHM J 1/6 56K OHM J 1/6 4.7K OHM J 1/4 20 OHM J

51

LOC R522 R524 R525 R526 R527 R533 R535 R541 R543 R545 R551 R552 R553 R556 R557 R558 R559 R560 R561 R562 R571 R572 R574 R575 R577 R578 R579 R580 R582 R583 R584 R585 R586 R591 R592 R594 R601 R602 R605 R606

PART-CODE RD-AZ203JRD-4Z101JRD-4Z121JRD-AZ473JRD-4Z433JRD-AZ472JRD-AZ473JRD-AZ331JRD-AZ331JRD-AZ331JRD-4Z100JRD-AZ473JRD-AZ102JRD-AZ109JRD-AZ102JRD-AZ102JRD-AZ102JRD-AZ472JRD-AZ472JRD-AZ472JRD-4Z471JRD-AZ102JRD-2Z100JRD-4Z279JRD-4Z470JRD-4Z109JRD-AZ822JRD-AZ332JRD-AZ822JRD-AZ104JRD-AZ102JRD-AZ332JRD-4Z229JRN-AZ9092F RD-AZ512JRD-AZ512JRD-AZ105JRD-2Z100JRD-AZ203JRD-AZ392J-

PART-NAME R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R METAL FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM

PART-DESC 1/6 20K OHM J 1/4 100 OHM J 1/4 120 OHM J 1/6 47K OHM J 1/4 43K OHM J 1/6 4.7K OHM J 1/6 47K OHM J 1/6 330 OHM J 1/6 330 OHM J 1/6 330 OHM J 1/4 10 OHM J 1/6 47K OHM J 1/6 1K OHM J 1/6 1 OHM J 1/6 1K OHM J 1/6 1K OHM J 1/6 1K OHM J 1/6 4.7K OHM J 1/6 4.7K OHM J 1/6 4.7K OHM J 1/4 470 OHM J 1/6 1K OHM J 1/2 10 OHM J 1/4 2.7 OHM J 1/4 47 OHM J 1/4 1 OHM J 1/6 8.2K OHM J 1/6 3.3K OHM J 1/6 8.2K OHM J 1/6 100K OHM J 1/6 1K OHM J 1/6 3.3K OHM J 1/4 2.2 OHM J 1/6 90.9K OHM F 1/6 5.1K OHM J 1/6 5.1K OHM J 1/6 1M OHM J 1/2 10 OHM J 1/6 20K OHM J 1/6 3.9K OHM J

52

LOC R607 R611 R751 R752 R758 R759 R802 R803 R814 R832 R833 R844 R855 R862 R863 R874 R881 R902 R903 R904 R905 R906 R907 R908 R909 R910 R911 R916 R935 R937 R939 R940 R941 R943 R944 R945 R946 R947 R994 R997

PART-CODE RD-AZ153JRD-AZ103JRD-AZ153JRD-AZ332JRD-2Z202JRD-2Z202JRD-AZ101JRD-AZ330JRD-AZ100JRD-AZ101JRD-AZ330JRD-AZ100JRD-AZ472JRD-AZ101JRD-AZ330JRD-AZ100JRD-AZ472JRD-AZ154JRD-AZ623JRD-AZ472JRD-AZ752JRD-AZ204JRD-AZ473JRD-AZ472JRD-AZ202JRD-AZ562JRD-AZ303JRD-AZ563JRD-AZ823JRD-AZ333JRD-AZ104JRD-AZ104JRD-AZ242JRD-AZ471JRD-AZ471JRD-AZ182JRD-AZ101JRD-AZ272JRD-AZ821JRD-AZ101J-

PART-NAME R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM

PART-DESC 1/6 15K OHM J 1/6 10K OHM J 1/6 15K OHM J 1/6 3.3K OHM J 1/2 2K OHM J 1/2 2K OHM J 1/6 100 OHM J 1/6 33 OHM J 1/6 10 OHM J 1/6 100 OHM J 1/6 33 OHM J 1/6 10 OHM J 1/6 4.7K OHM J 1/6 100 OHM J 1/6 33 OHM J 1/6 10 OHM J 1/6 4.7K OHM J 1/6 150K OHM J 1/6 62K OHM J 1/6 4.7K OHM J 1/6 7.5K OHM J 1/6 200K OHM J 1/6 47K OHM J 1/6 4.7K OHM J 1/6 2K OHM J 1/6 5.6K OHM J 1/6 30K OHM J 1/6 56K OHM J 1/6 82K OHM J 1/6 33K OHM J 1/6 100K OHM J 1/6 100K OHM J 1/6 2.4K OHM J 1/6 470 OHM J 1/6 470 OHM J 1/6 1.8K OHM J 1/6 100 OHM J 1/6 2.7K OHM J 1/6 820 OHM J 1/6 100 OHM J

53

LOC R998 R999 TP1 30020 CA804 CA805 CT801 CW801 CW802 C851 C891 C892 CA803 IC803 P11 SC801 SG891 40010 C805 C806 C807 C821 C822 C835 C836 C837 C852 C865 C866 C867 C893 C894 C895 Q805 Q806 Q835 Q836 Q865 Q866 50010

PART-CODE RD-AZ471JRD-AZ433J85801052GY PCCTSWJ046 9970710181 9970710181 9979300008 9979220025 9979220022 CMXM2A224J CCXE3D103P CCXB3D471K 9970710179 1LM2407T-4859242220 9977410800 4SG0D00104 PCCTJRJ046 CEXD1H109F CMXM2A222J CMXM2A333J CCXF1H104Z CEXF1E101V CEXD1H109F CMXM2A222J CMXM2A333J CEXF2A470V CEXD1H109F CMXM2A222J CMXM2A333J CCXB1H103K CCXB1H102K CEXF2A220V TKSC1009YTKSA910Y-TKSC1009YTKSA910Y-TKSC1009YTKSA910Y-PCCTJAJ046

PART-NAME R CARBON FILM R CARBON FILM WIRE COPPER PCB CRT AS CONN AS CONN AS SOCKET CRT CONN WAFER CONN WAFER C MYLAR C CERA C CERA CONN AS IC VIDEO OUTPUT CONN WAFER TERMINAL PIN SPARK GAP PCB CRT RADIAL AS C ELECTRO C MYLAR C MYLAR C CERA C ELECTRO C ELECTRO C MYLAR C MYLAR C ELECTRO C ELECTRO C MYLAR C MYLAR C CERA C CERA C ELECTRO TR TR TR TR TR TR PCB CRT AXIAL AS

PART-DESC 1/6 470 OHM J 1/6 43K OHM J 1/0.52 TIN COATING CMC-710B 1015#18+35068-9812=110 1015#18+35068-9812=110 033 0 7700 44 SMAW250-10 (ANGLE) SMAW250-07 (ANGLE) 100V 0.22MF J HIKE 2KV 0.01MF P 2KV B 470PF K (TAPPING) 1015#18+4.3PIEX2=160 LM2407T YFW800-02 BSP1(SN) L=15MM S-23 1.5KV CMC-710B 50V RND 1MF (5X11) TP 100V 2200PF J (TP) 100V 0.033MF J (TP) 50V F 0.1MF Z 25V RSS 100MF (6.3X11) TP 50V RND 1MF (5X11) TP 100V 2200PF J (TP) 100V 0.033MF J (TP) 100V RSS 47MF (10X16) TP 50V RND 1MF (5X11) TP 100V 2200PF J (TP) 100V 0.033MF J (TP) 50V B 0.01MF K 50V B 1000PF K (TAPPING) 100V RSS 22MF (8*11.5) KSC-1009-Y KSA910Y KSC-1009-Y KSA910Y KSC-1009-Y KSA910Y CMC-710B

54

LOC B0001 B803 B805 B811 B812 B813 B814 B859 B863 B864 D803 D804 D805 D833 D834 D835 D863 D864 D865 L801 L831 L861 R804 R805 R807 R808 R809 R810 R811 R812 R822 R834 R835 R837 R838 R839 R840 R841 R842 R852

PART-CODE 9979800463 5PB13857-5PB13857-5PB13857-5PB13857-5PB13857-5PB13857-5PB13857-5PB13857-5PB13857-DFDH400--DFDH400--DFDH400--DFDH400--DFDH400--DFDH400--DFDH400--DFDH400--DFDH400--5CPZ568K02 5CPZ568K02 5CPZ568K02 RD-4Z271JRD-4Z101JRC-2Z470JRD-AZ133JRD-AZ683JRD-AZ224JRD-AZ154JRD-AZ474JRD-2Z104JRD-4Z271JRD-4Z101JRC-2Z470JRD-AZ133JRD-AZ683JRD-AZ224JRD-AZ154JRD-AZ474JRD-2Z104J-

PART-NAME PCB VIDEO COIL BEAD COIL BEAD COIL BEAD COIL BEAD COIL BEAD COIL BEAD COIL BEAD COIL BEAD COIL BEAD DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE COIL PEAKING COIL PEAKING COIL PEAKING R CARBON FILM R CARBON FILM R CARBON COMP R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON COMP R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM

PART-DESC T1.6*244*246 BI3857(AXIAL) BI3857(AXIAL) BI3857(AXIAL) BI3857(AXIAL) BI3857(AXIAL) BI3857(AXIAL) BI3857(AXIAL) BI3857(AXIAL) BI3857(AXIAL) FDH400 FDH400 FDH400 FDH400 FDH400 FDH400 FDH400 FDH400 FDH400 0.56UH K (AXIAL 3.5MM) 0.56UH K (AXIAL 3.5MM) 0.56UH K (AXIAL 3.5MM) 1/4 270 OHM J 1/4 100 OHM J 1/2 47 OHM J 1/6 13K OHM J 1/6 68K OHM J 1/6 220K OHM J 1/6 150K OHM J 1/6 470K OHM J 1/2 100K OHM J 1/4 270 OHM J 1/4 100 OHM J 1/2 47 OHM J 1/6 13K OHM J 1/6 68K OHM J 1/6 220K OHM J 1/6 150K OHM J 1/6 470K OHM J 1/2 100K OHM J

55

LOC R864 R865 R867 R868 R869 R870 R871 R872 R882 R891 R892 R893 SG801 SG831 SG861

PART-CODE RD-4Z271JRD-4Z101JRC-2Z470JRD-AZ133JRD-AZ683JRD-AZ224JRD-AZ154JRD-AZ474JRD-2Z104JRD-4Z562JRD-4Z564JRD-AZ103JDWSP201M-DWSP201M-DWSP201M--

PART-NAME R CARBON FILM R CARBON FILM R CARBON COMP R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM SURGE ABSORBER SURGE ABSORBER SURGE ABSORBER

PART-DESC 1/4 270 OHM J 1/4 100 OHM J 1/2 47 OHM J 1/6 13K OHM J 1/6 68K OHM J 1/6 220K OHM J 1/6 150K OHM J 1/6 470K OHM J 1/2 100K OHM J 1/4 5.6K OHM J 1/4 560K OHM J 1/6 10K OHM J WSP-201M WSP-201M WSP-201M

56

Serv ce Manual
DAEWOO ELECTRONICS CO., LTD OVERSEAS SERVICE DEPT. DAEWOO ELECTRONICS CO., LTD
686, AHYEON-DONG MAPOGU, SEOUL, KOREA. C.P.O. BOX 8003 SEOUL KOREA TELEX: DWELEC K28177-8 CABLE: "DAEWOOELEC" FAX: 02) 590-6291 TEL: 02) 360-7114/590-6151~5 http://www.dwe.daewoo.co.kr

PRINTED DATE: NOV.1998