Text preview for : 7050e010.pdf part of konica 7050e 7050e service manual and instructions
Back to : 7050e.zip | Home
1
OPERATION
1. OPERATION
OPERATION PANEL .....................................1-1 COPY OPERATION ......................................1-3 [1] 2-in-1/4-in-1 ..........................................1-3 [2] Inter-sheet Mode ..................................1-3 [3] OHP Interleave Mode ..........................1-6 [4] Repeat Function ...................................1-6 [5] Proof Copy ...........................................1-6 [6] Book Memory Function ........................1-7 [7] Image insertion Function ......................1-7 [8] Chapter Control Function .....................1-8 [9] Non-image Area Erase Function ..........1-8 [10] Reading/Writing Mode (Job Memory) .1-8 [11] Black-and-White Reversal Mode ........1-9 [12] Book Copy Mode ................................1-9 [13] Operation for Memory Overflow .......1-10 VARIOUS SETTINGS ..................................1-11 [1] Independent Magnification Change Function ................................1-11 [2] Arbitrary Magnification Setting ...........1-11 [3] Maximum Magnification/Minimum Magnification Jump Function .............1-11 [4] Arbitrary Density Setting ....................1-11 [5] Density Shift Setting ........................... 1-12 [6] Selecting an Image Reading Mode ....1-12 [7] Character/Photograph Mode ..............1-12 [8] Mixed Originals Copy .........................1-13 [9] Frame Erasing/Fold Erasing Mode ....1-13 [10] Shift/Reduction Shift Mode ...............1-13 [11] Weekly Timer(Option) ......................1-16 [12] E.K.C. (Electronic Key Counter) Mode .................................................1-22 [13] Auto Shut Off Setting ........................1-26 [14] Auto Reset ........................................1-26 COUNT NUMBER CONFIRMATION ...........1-27 [1] PM Count ...........................................1-27 [2] Drum Count ........................................1-27 MESSAGE LIST .......................................... 1-28 [1] Bases .................................................1-28 [2] Warning ..............................................1-28 [3] Interruption Copy ...............................1-32 [4] P Function .......................................... 1-32 [5] Jam ....................................................1-33 [6] Troubles ............................................. 1-34 [7] Adjustment ......................................... 1-34 [8] Electronic Key Counter ......................1-35 [9] Book Copy · Inter-sheet · Chapter Sectioning · Insertion Page ................1-36 [10] OHP Interleave · Shift · Single Step · Density Monitor · Repeat Mode .........1-37 [11] Job Memory ......................................1-38 [12] Others ............................................... 1-39
OPERATION
OPERATION PANEL
1 2 3 4 5 6 7 8 9 10 11 12 13
ON OFF
ORIGINAL
COPY
MEMORY 2 MEMORY 1
SPECIAL RATIO 2 SPECIAL RATIO 1
WEEKLY TIMER
2
14 15 5 13 10 9 8 1 2 11 4 3 12 7 6
2 1 2 1
A4 A3 A4 B4
/ A5 A4
2
M
1
B4 A3 A3 B4 B4 A4R
/ B5 A4 / A4 B5
1 1
A3 A4R / A4 A5R
ZOOM RE 1:1
COPY MODE
24
23 22
21
20
19
18
17
16
15
14
No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
Name Weekly timer display Timer release button Timer setting button Fold erasure.frame erasure button Non-image area erasure button Character/photograph button. Repeat button Image insertion/chapter classify button Inter-sheet button Thin paper/thick paper button OHP interleave button Independent magnification button Magnification display Magnification button Size reduction/enlargement button Copy density button Copy mode button 2-in-1/4-in-1 button Book copy button Black and white reversal button
Function Weekly timer control is displayed. (Indication with lighting) A weekly timer setting mode is released. A weekly timer control mode is started. To select a frame erasure mode, a fold erasure mode or a frame erasure/fold erasure mode. Outside of an original is erased. To select a character mode, a photograph mode or a character/photograph mode. A designated image area is printed repeatedly on a single copy paper. To select an image insertion mode or a chapter sectioning mode. To select inter-sheet 1 - 4 modes. To select a thin paper copy mode or a thick paper copy mode. To select an OHP interleave(copy/blank paper) mode. To establish longitudinal and widthwise magnifications independently. To indicate the selected magnification with figures. (Indication with lighting) To select an auto mode, a zoom mode or a fixed mode all in a magnification mode. To change a copy magnification. To change copy density. To select a two-sided (one-sided) original/duplex (one-sided) copy mode To select a 2-in-1 mode or a 4-in-1 mode by combining with a copy mode button. To select a book copy mode. A white area and a black area both in an effective area are reversed.
1-1
OPERATION
26
27
28
29
30
1
A5 8 X13 F4 A4R B5R A4 B5 A3 B4
,,
2 5 8 0
RECALL
3 6 9
STAPLE GROUP SORT
OUTPUT 1:1 APS AE ADF
4
C
7 P
2
F 3
F 4
AUTO
40
39
38
37
36
35 34
33 32
31
No. 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40
Name Reduction shift/shift button Mixed originals button Job memory button Paper jam display Message display Platen memory button Image reading button Copy quantity setting button Copy quantity display Pre-heating button Interruption button Copy button Stop/clear button Recall button P button Auto button Paper size button Output button Proof copy button Menu selecting button
Function To select a reduction shift mode or a shift mode. To select a mixed mode for originals in the same series. To select a writing mode or a reading mode for copy patterns. Locations of paper jam are indicated with figures. Procedures for operation and the conditions of a machine are indicated with alphabet. A platen memory copy mode is selected. To select a normal mode, a fine mode or a super-fine mode for image reading. A copy quantity is set. To indicate the selected copy quantity and copy count in copying. To set to a pre-heating mode. To select an interruption mode. To start copying. To discontinue copying and cancel copy quantity set. To confirm the set copy quantity in the course of copying. To read various settings and counts. To select finisher, 1:1, APS, AE or ADF mode. To select paper trays. (paper sizes) To select a stapling mode, a grouping mode or a sorting mode. To select a proof copy mode. Confirmation and selection are made on a menu screen.
1-2
OPERATION
COPY OPERATION
[1] 2-in-1/4-in1
Plural originals are copied on a single copy paper. originals are copied in the order of reading originals for a [2-in-1 mode], and originals are copied in the order to a weekly-magazine binding for a [4-in-1 mode].
[2] Inter-sheet Mode
This mode is used to insert blank sheets of colored paper, for example, at arbitrary positions among the copies, or to copy arbitrary originals on colored paper, for example.
1. Selection of a inter-sheet mode 1. Conditions for use
a. b. c. d. e. Originals in A4 and B5 sizes only are acceptable A3, B4, A4R and B5R are necessary for copy paper in accordance with originals. By-pass feed paper does not work. Only reduction shift function and single step function can be combined with 2-in-1 function. A stapling mode can not be selected. Each time the inter-sheet button is pressed, a mode is changed.
Normal state Inter-sheet mode Inter-sheet copy mode
Inter-sheet copy mode (cover mode)
Inter-sheet mode (cover mode)
2. Method of setting
(1) Set an original on an ADF. (2) Press a 2-in-1/4-in-1 button. (3) Press a copy mode button to select a copy mode. · Selection of one-sided original/one-sided copy and two-sided original/one-sided copy mode makes a 2in-1 mode. (Two originals are printed on the one copy paper.) Face side 1 2 3 4 ·· 11 12
2. Conditions of use
a. A machine is required to be with FS-102.
3. Inter-sheet mode
A paper with a different type can be inserted between ordinary copy papers without being copied. a. Method of setting (1) Ordinary copy paper is set on any one of trays 2, 3 and 4, copy paper to be inserted is set on tray 1, and an original is set on an ADF. (2) Press the inter-sheet button to select an inter-sheet mode. (3) Input the smaller number of original among others where a different type paper is to be inserted, using a copy quantity setting button. Original number 1 1 2 2 3 3 ··· 50 50
· Selection of one-sided original/duplex copy and twosided original/duplex copy mode makes a 4-in-1 mode. (Four originals are printed on the double sided copy to one copy paper.) Face side Reverse side
C
12 2
1 11
10 4
3 9
8 6
5 7 Place for insertion Set sheet number
(4) If necessary for booklet form, select reduction shift function.
· Maximum number of locations for setting: 7 locations · Maximum number of set sheets: 50 sheets · For the one-sided original/duplex copy mode, only designation of even number pages is effective. (4) Press the set/F1 button after inputting one set sheet number. When inputting plural set sheet numbers, repeat from (3). (5) After inputting all set sheet numbers, press the set/F1 button further for completion of setting. · When a stop/clear button is pressed, setting is canceled. (6) Use a copy button for printing.
1-3
OPERATION
b. Examples of using inter-sheet mode Example) Setting number: To set to 3 Original numbers 1 2 3 4 Insertion position Set sheet number 3 Copy result
1 2 3 4 5 6 1 2 3 4 5 6
4. Inter-sheet copy mode
5 6 Between ordinary copy papers, a different type paper (color paper for sectioning chapters) is inserted after being copied. a. Method of setting (1) Ordinary copy paper is set on any one of trays 2, 3 and 4, copy paper to be inserted is set on tray 1, and an original is set on an ADF. (2) Press the inter-sheet button to select an inter-sheet mode. (3) Input the number of an original to be copied on a different type paper with a copy quantity setting button. Original number Set sheet number
See *1.
One-sided one-sided
Inter-sheet
Inter-sheet
One-sided two-sided
1 2 3 4 5 6
1 3 5
2
4 6
1 1
2 2
3 3
···
50 50
Two-sided one-sided
1 3 5 7 9 11
2
4 6 8 10 12
1 6 7 12
Inter-sheet
See *2.
Two-sided two-sided
1 3 5 7 9 11
2
4 6 8 10 12
1 3 5
7 9 11
2
4 6 8 10 12
Inter-sheet
See *2.
· Maximum number of locations for setting: 7 locations · Maximum number of set sheets: 50 sheets · For the one-sided original/duplex copy mode, only designation of even number pages is effective. (4) Press the set/F1 button after inputting one set sheet number. When inputting plural set sheet numbers, repeat from (3). (5) After inputting all set sheet numbers, press the set/F1 button further for completion of setting. · When a stop/clear button is pressed, setting is canceled. (6) Use a copy button for printing.
*1: Since it is not possible to insert between face 3 and face 4, 1 is added to the set number and an inter-sheet is inserted after the 4th original. *2: In the inter-sheet mode, the original number corresponds to the number of originals. When the set number is set to 3, an inter is inserted before the 4th original.
1-4
OPERATION
b. Examples of using inter-sheet mode Example) Setting number: To set to 3 Original numbers 1 2 3 Set sheet number 3
5. Inter-sheet mode (cover mode)
4 5 6 Different type papers (thick papers) fed through by-pass feed are ejected without being copied to be positioned before the lead paper for ordinary copying (to be a front cover) and after the last paper (to be a back cover).
C
Copy result
Inter-sheet
Note: Paper size of selected tray and that of by-pass feed must be coincident. a. Method of setting (1) Set an original on the ADF. Feed the front cover and the back cover through by-pass feed. (2) Press the inter-sheet button to select an inter-sheet mode (a cover mode). (3) Use a copy button for printing.
One-sided one-sided
1 2 3 4 5 6
1 2 3 4 5 6
Inter-sheet
One-sided two-sided
1 2 3 4 5 6
1 3 5
2
4 6
6. Inter-sheet copy mode (cover mode)
See *1. Inter-sheet
Two-sided one-sided
1 3 5
2
4 6
1 2 3 4 5 6
Different type papers (thick papers) fed through by-pass feed are ejected after being copied to be positioned before the lead paper for ordinary copying (to be a front cover) and after the last paper (to be a back cover).
C
See *2.
Note: Paper size of selected tray and that of by-pass feed must be coincident. a. Method of setting (1) Set an original on the ADF. Feed the front cover and the back cover through by-pass feed. (2) Press the inter-sheet button to select an inter-sheet copy mode (a cover mode). (3) Use a copy button for printing.
Two-sided two-sided
Inter-sheet
1 3 5
2
4 6
1 3 5
2
4 6
See *2.
*1: Face 4 is copied on the reverse side of an inter-sheet. *2: In the inter-sheet mode, face 3 is copied on the inter-sheet because the set sheet number corresponds to the number of original faces.
1-5
OPERATION
[3] OHP Interleave Mode
When copying on an OHP film, white paper (OHP mode) or copy paper for the same original (OHP copy mode) is ejected as a lining paper.
[5] Proof Copy
When printing plural sets, conduct output for printing for only one set first, then stop printing temporarily, change a mode, and then conduct printing for the remaining sets.
1. Selection of OHP interleave mode
Each time the OHP interleave button is pressed, a mode is changed.
Normal state OHP mode OHP copy mode
1. Conditions of use
a. b. c. d. Combination with a density monitor function is impossible. Under the interruption mode, the proof copy is not accepted. The proof copy can not be selected under the group mode. The proof copy can not be selected under the platen copy.
2. Conditions of use
a. b. An OHP film is inserted in a tray for by-pass feed. A copy mode is limited only to those of one-sided original/one-sided copy and two-sided original/onesided copy. An output button is not accepted. A cassette other than a tray for by-pass feed can be designated for interleave, and its size is required to be the same as the OHP film.
2. How to operate
(1) (2) (3) (4) Set the original on the ADF. Select the function. Press the proof copy button. Press the copy button to start printing. (When the other function is selected, start printing with the How to operate in that selected function.) (5) Stop printing temporarily after completion for one set. (6) Select the change to other function. (7) Press the copy button further for printing for the remaining sets.
c. d.
[4] Repeat Function
Only a designated area is printed on a single copy paper repeatedly. (only in the primary scanning direction)
3. Change after temporary stop 1. How to operate
(1) Press the repeat button. (2) Set the original to be copied repeatedly so that the original is aligned with the trailing edge (rear side on the left) of the A3 scale plate. (3) Set the image area to be copied with an increment of 1 mm using the copy quantity setting button. (0 - 150) (4) When a set/F1 button is pressed, the image area is decided. (5) Use a copy button to print on a single copy paper repeatedly. While printing is stopped temporarily, the following mode or function can be changed. a. Output mode (provided that a group mode is not accepted) b. Copy quantity (number of sets) c. Thick paper/thin paper
Increment of 1 mm Platen glass
1-6
OPERATION
[6] Book Memory Function
In a platen mode, originals are scanned one by one, and images thus stored in ERDH are printed on a nonstop basis. In a platen mode, it is possible to perform an operation identical to outputting in an ADF mode.
[7] Image insertion Function
Establishment of sheet numbers makes it possible to insert an image read with platen in any place in images taken in with ADF original.
1. Conditions of use 1. Conditions of use
a. b. Platen mode Combinations with the following buttons are impossible. · Book copy button · Inter-sheet button · OHP interleave button · Job memory button · Mixed original button AMS is impossible. a. b. c. d. Maximum number of locations for setting: 7 locations Maximum number of set sheets: 50 sheets In an APS mode, only a size of the first original in ADF originals is detected. An input of the same number is possible. An original with the following same number is inserted right after the inserted original with the preceding same number.
2. How to operate
(1) Use a image insertion/chapter sectioning button to establish a image insertion mode. (2) Input the image data to be read in a platen mode (insertion original) as a number of the original to be inserted, using a copy quantity setting button. (For example, when inserting after the second one, input 2.) Original number 1 2 2 3 ··· 50
c.
2. How to operate
(1) (2) (3) (4) Press the platen memory button. Set an original in a platen mode. Press the set/F1 button to read an original in a memory. Repeat the aforementioned items (2) and (3) for all originals. (5) After reading all originals, press the set/F1 button to confirm. (6) Use a copy button for printing.
Place for insertion Sheet number to be set
(3) Confirm by the use of the set/F1 button. · It is possible to cancel the numerical value inputted with a stop/clear button. (4) Repeat the aforementioned items (2) and (3) when setting the number of the other original to be inserted. (5) After completion of inputting, press the set/F1 button again for the completion of setting. (6) When the set/F1 button is pressed after an original is set on an ADF, an ADF original is read. (7) After reading from an ADF is completed, when an original to be inserted is set on a platen and the set/F1 button is pressed, the original to be inserted is read. (8) When making other original for insertion to be read, repeat the item (7). (9) Use a copy button for printing.
1-7
OPERATION
[8] Chapter Control Function
Be sure to make the forefront of each chapter to be the face side of a page. In setting the original sheet number of the forefront of each chapter in a one-sided original/duplex copy mode, when that sheet falls on the back side of a page, it is necessary that the back page is ejected without being copied and the following face side page is copied.
[9] Non-image Area Erase Function
This is a function on the assumption of book copy, and it detects an original through pre-scanning and thereby erases an original margin automatically, when copying in the state of opened ADF. 1. Conditions of use a. An ADF is opened. 2. How to operate (1) Open the ADF. (2) Press the non-image area erasure button. (3) Set an original on a platen. (4) Use a copy button for printing. 3. Others When an ADF is closed, images on an entire page of the original are outputted. (An area exceeding the original size can also be used for copying, when necessary.)
1. Conditions of use
a. b. c. Maximum number of locations for setting: 7 locations Maximum number of set sheets: 50 sheets An ERDH mode is selected automatically. Under the condition that the ERDH mode can not be selected, the chapter control function can not be selected. In a super fine mode, the chapter control function is canceled automatically. A copy mode is possible only for a one-sided original/ duplex copy mode.
d. e.
2. How to operate
(1) Use a image insertion/chapter sectioning button to establish a chapter sectioning mode. (2) Input the number of an original sheet representing the forefront of a chapter, using a copy quantity setting button. Original number
C
[10] Reading/Writing Mode (Job Memory)
Write a copy pattern set together with a writer number and read the copy pattern registered by means of the writer number when necessary.
1
2
3 3
···
50
1. Selection of a reading/writing mode
Every time a job memory button is pressed, a mode is changed.
Normal status A job memory reading mode
Place for chapter Sheet number to be set
(3) Confirm by the use of the set/F1 button. · It is possible to cancel the numerical value inputted with a stop/clear button. (4) When setting the number of an original sheet representing the forefront of another chapter, repeat the aforementioned items (2) and (3).. (5) After completion of inputting, press the set/F1 button again for the completion of setting. (6) Set an original on an ADF. (7) Use a copy button for printing.
A job memory writing mode
a. b.
In a reading mode, a reading LED is flickered. In writing mode (the job memory writer mode), a writing LED is flickered.
2. Writing method
(1) Display a copy pattern written on the job memory on a display panel. (2) Press the job memory button and select the writing mode (the job memory writer mode). (3) Input the writer number by means of the copy quantity setting button (0 to 9). (4) After writing is completed, the writing LED is lit.
1-8
OPERATION
3. Reading method
(1) Press the job memory button, and select the reading mode. (2) Input the register number already registered by means of the copy quantity setting button (0 to 9). (3) The copy pattern read is displayed on the display panel. (4) Press the P button, and finalize. (5) After reading is completed, the reading LED is flickered.
[12] Book Copy Mode
It copies an original image (1 page) for 2 pages in terms of one side or copies on the face side and the rear side of a copy paper.
1. Use condition
a. b. c. d. e. f. Original size: A3/B4. Copy paper size: A4/B5 Only a one side original/one side copy mode and a one side original/two sided copy mode is allowed. It is impossible to change the order of pages. It is impossible to provide a white paper. When 2 in 1/4 in 1 button is pressed in selecting a book copy mode, papers can be changed to the order of copying in the same order of the 2 in 1 mode.
[11] Black-and-White Reversal Mode
Reverse a white portion and black portion in a valid region.
C
1. Selecting a black-and-white reversal copy button.
(1) Press a black-and-white reversal button. (2) A black-and-white reversal LED is lit.
C
Note: For the machines equipped with controller ROM C1/C2 of Ver.15 or older, or image process ROM of Ver 14 or older; When the book copy mode and a function of erasing outside original are selected concurrently, the range of erasing outside the original is not guaranteed for non-regular size documents.
2. Setting method
(1) Press the book copy button. (2) Set an original (1 page) covering 2 pages of a one side in a platen mode. (3) Press a set/F1 button, and read the original on the memory. (4) Repeat (2) and (3) above for the entire original. (5) After reading the entire original, press the set/F1 button for finalizing. (6) Print it by means of the copy button.
3. Outputting order
· Original for 2 pages of one side original. 1 2 3 4 5 6
a.
Outputting in the one side original/one side copy mode. 1 2 3 4 5 6
b.
Outputting in the one side original/two sides copy mode Face side 1 3 5
Back side
2
4
6
1-9
OPERATION
[13] Operation for Memory Overflow
1. Real time output mode
One copy for the scanned data is outputted, and the copy operation stops regardless of the selected copy quantity. The memory overflow message will appear alternatively.
2. Memory output mode
The scanned data is maintained. After the machine stops running, the memory overflow message will appear alternatively. In this case, no copy paper exit will be executed.
When you continue copying:
(1) Press the copy button to copy the rest of the selected number of the scanned data. · The staple is canceled if it is selected, and the copy operation is executed in the sorting mode. · If the second and later copy is operated, the page that was during process when the memory overflow has occurred, is not copied. Therefore, note that one or two pages may be skipped. (2) When the selected number of copies are completed, the copy operation stops and all memory will be cleared. CHECK/RELOAD ORIGINAL COPY KEY : CLR/AUTO KEY : CANCEL (3) Check the number of originals then press the copy button to copy the rest.
When you continue copying:
(1) Press the copy button to copy the selected number of the scanned data. (2) When the selected number of copies are completed, the copy operation stops and all memory will be cleared. CHECK/RELOAD ORIGINAL COPY KEY : CLR/AUTO KEY : CANCEL (3) Check the number of originals then press the copy button to copy the rest.
When you stop copying:
(1) Press either stop/clear or auto button. SET FEWER ORIGINALS AND REPROGRAM JOB (2) All memory will be cleared. · Press the stop/clear button to maintain the settings and the auto button to return to the automatic state.
When you stop copying:
(1) Press either stop/clear or auto button. SET FEWER ORIGINALS AND REPROGRAM JOB (2) All memory will be cleared. · Press the stop/clear button to maintain the settings and the auto button to return to the automatic state.
1 - 10
OPERATION
VARIOUS SETTINGS
[1] Independent Magnification Change Function
Each of lengthwise magnification and widthwise magnification is changed independently for copying.
2. Setting arbitrary magnification 2
(1) Select the fixed magnification mode with a magnification button, and select the arbitrary magnification 2 with an enlargement ( ) button. (2) Press the magnification button while pressing a P button under the condition that "arbitrary magnification 1" is set. (3) Set the magnification with a copy quantity setting button. (50 - 400%) (4) Press the P button for completion of setting.
1. Conditions of use
a. b. c. Combination with book copy, shift or reduction shift does not work. An APS function is released. Established lengthwise magnification and widthwise magnification continue to be stored, except the following.items. · Power OFF · Auto shut off · Pre-heating mode · Job memory reading
3. How to select
Arbitrary magnification 1 and arbitrary magnification 2 both set can be selected by pressing the enlargement button ( ).
2. How to select
(1) Press an independent magnification change button to select lengthwise magnification or widthwise magnification. (2) Use an enlargement ( ) button or a reduction ( ) button to select the magnification. · Lengthwise magnification or widthwise magnification is displayed on a message indicator.
[3] Maximum Magnification/Minimum Magnification Jump Function
1. How to select
a. b. For selecting the maximum magnification (4.00), press an enlargement button ( ) while pressing a P button. For selecting the minimum magnification (0.50), press a reduction button ( ) while pressing a P button.
2. Conditions of use
a.
[2] Arbitrary Magnification Setting
In addition to fixed magnifications, arbitrary magnifications can also be set and stored. The arbitrary magnification can be set within a range of 0.50 - 4.00. Both arbitrary magnification 1 and arbitrary magnification 2 can be set. 1. Setting arbitrary magnification 1 (1) Press the magnification button while pressing a P button under the condition that "arbitrary magnification 2" is not set. (2) Set the magnification with a copy quantity setting button. (50 - 400%) · 50% inputs "050" and 400% inputs "400". (3) Press the P button for completion of setting. · At this moment, when a stop/clear button is pressed, it is possible to get out of a setting mode without storing the set data.
Execution of this function establishes a zoom magnification mode.
[4] Arbitrary Density Setting
Arbitrary density is set and stored. A sheet of an original is divided into four, and prints each being different in terms of density are made. Arbitrary density 1 and arbitrary density 2 can be set.
C
1. Setting arbitrary density 1 (For light original)
(1) Set an original in a platen mode. (2) Press the darker button ( ) in copy density button while pressing a P button. (3) Press a copy button. Then, 4-divided sample images (1 - 4) each being different in terms of density are printed. (4) After that, each time the copy button is pressed, sample images (5 - 8), (9 - 12) and (13 - 16) are printed. (5) Input the number of the desired density with a copy quantity setting button. (6) Use a set/F1 button for decision.
1 - 11
OPERATION
C
2. Setting arbitrary density 2 (For dark original)
Conduct the same operations as in the aforementioned "Setting arbitrary density 1" except the item (2). (1) Press the lighter button ( ) in copy density button while pressing a P button.
[6] Selecting an Image Reading Mode
An image reading mode for an image under electronic RDH is selected.
1. Selection of an image reading mode
"Normal", "Fine" and "Super fine" are switched by pressing an image reading button. Fine LED Normal Fine Super fine a. b. Lights-out Lighting Lights-out Super fine LED Lights-out Lights-out Lighting
3. How to select
a. When keep pressing the lighter button ( ) in copy density button shifting from arbitrary density 1 to arbitrary density 2 is carried out. Press the lighter button ( ) in copy density button while pressing a P button to select the arbitrary density 2. Press the darker button ( ) in copy density button while pressing a P button to select the arbitrary density 1.
b.
c.
[5] Density Shift Setting
Ordinary density for each of characters, photographs and character/photograph modes can be set. Density in 5 steps from dark to light can be set. When characters, photographs and character/photograph modes are selected, this ordinary density is selected automatically.
c.
Normal mode: To be selected when the number of originals is large. Fine mode: To be selected when the number of originals is small and image quality is important. Super fine mode: To be selected for a delicate original such as a photographic original.
Note: When memory overflow occurs in a fine mode, change the fine mode to a normal mode.
2. Conditions of use
a. Super fine mode is allowed only when electronic RDH is not used. Therefore, an ADU mode and special functions can not be used.
1. Conditions of use
a. b. Under the state of idling or a copy mode Not possible in 35 and 36 modes
2. How to set
(1) Select "character", "photograph" or "character/photograph" mode with a character/photograph button. (2) Press a copy quantity setting 3 button while pressing a P button. (3) Set the ordinary density corresponding to the mode selected in the aforementioned item (1), using copy quantity setting buttons 1 - 5. (1: darker 5: lighter) (4) Press a set/F1 button for decision. (5) Set the ordinary density for another mode by repeating the aforementioned items (1) - (4).
[7] Character/Photograph Mode
Output for "photograph" use, "character" use or "character/ photograph" use is selected depending on the type of an original image so as to select the function for reproducing an original on a high fidelity basis.
1. Selection of character/photograph
"Photograph", "character" and "character/photograph" modes are switched when a character/photograph button is pressed. Character LED Character mode Photograph mode Character/photograph mode Lighting Lights-out Lights-out Photograph LED Lights-out Lighting Lights-out
1 - 12
OPERATION
[8] Mixed Originals Copy
Mixture of the same series originals is made possible under the use of an ADF. When an APS or an AMS is selected, paper size is detected for each original for selection of paper size or selection of magnification.
(2) Press a P button. (3) Input an amount of frame erasing (5, 10, 15) and an amount of folding erasing (10, 20, 30) by means of the copy quantity setting button. (4) Press the P button. Note: After inputting data by means of the copy quantity setting button, when the P button is not pressed for 10 seconds, the data during inputting is canceled.
1. How to select
Set the mixture of the same series originals on the ADF and press the mixed original button.
2. Conditions of use
a. b. c. d. Number of original faces: up to 100 faces Original size: A3/A4, B4/B5 By-pass feed paper supply is excluded. A size falls on one on the reverse side for one-sided original/duplex copy.
3. Paper size capable of conducting fold erasing and frame erasing.
The following table shows paper sizes capable of being used. Fold erasing/ Frame erasing + fold erasing A3, B4, A4R, B5R
[9] Frame Erasing/Fold Erasing Mode
To select frame erasing and fold erasing and to set an amount of erasing when copying.
Frame erasing
A3, B4, A4R, B5R, A4, B5, A5
1. Amount of frame erasing and fold erasing
[10] Shift/Reduction Shift Mode
It forms image shift on a copy paper.
1. Selecting a shift/reduction shift mode
Every time the reduction shift/shift button is pressed, a mode is changed.
Frame erasing Fold erasing Normal status Shift mode Reduction/shift mode
2. Shift mode
An amount of erasing capable of being set is shown in the following table. (Unit: mm) Fold erasing Frame erasing 10 5 20 10 30 15
C
In case of front side, the image is shifted towards the subscanning direction according to the selected shift amount. The trail edge of image will be deleted by the shifted distance.
Stopper plate side Shift amount
2. Setting method
(1) Press a folding erasing/frame erasing button for selecting a mode. An LED selected is lit.
Normal status Frame erasing Frame erasing + fold erasing Fold erasing
1 - 13
OPERATION
In case of rear side, select either of the followings in the 25 mode. · Image is shifted towards the sub-scanning direction according to the selected shift amount.
Stopper plate side
Shift amount
a. Use condition (1) It is possible to be used only in an equivalent magnification setting. (2) It is impossible to output on a real time basis. (3) It is impossible to use an super fine mode. (4) It is invalid to set an shift amount of the front surface and the rear surface independently in a one side original/both sides copy mode. (5) In a platen mode, an original stopper plate side is shifted. b. Behavior corresponding to each copy mode Behavior of the shift function changes depending upon whether or not there is a copy mode and an original image shift. For an original not having the image shift, prepare the image shift. For an original having the image shift, align the image shift on the front surface and on the rear surface. · A one side original/one side copy mode (there is no image shift.) An odd number surface The rear edge (Inputting a front data.)
· The trail edge is deleted by the shifted distance.
An even number surface The rear edge (Inputting a front data.)
Stopper plate side
· A one side original/two sides copy mode (there is an image shift.: see "Adjustment `Mode 25'") An odd number surface Not shifted
An even number surface Front edge (Inputting a rear data.) · A one side original/two sides copy mode (there is no image shift.: see "Adjustment `Mode 25'") An odd number surface Rear edge (Inputting a front data.)
An even number surface Front edge (Inputting a rear data.) · Two sides original/one side copy mode (there is an image shift.: see "Adjustment `Mode 25'") An odd number surface Not shifted
An even number surface Rear edge (Inputting a rear data.) · Two sides original/one side copy mode (there is no image shift.: see "Adjustment `Mode 25'") An odd number surface Rear edge (Inputting a front data.)
An even number surface Rear edge (Inputting a rear data.) · Two sides original/two sides copy mode (there is no image shift.) An odd number surface Rear edge (Inputting a front data.)
An even number surface Front edge (Inputting a rear data.)
1 - 14
OPERATION
3. Reduction shift mode
Reduce an image in a manner that there is no image erasing according to a shift amount, and then, shift in a sub-scanning direction.
C
c. Magnification Magnification is automatically determined due to a shift amount and the size of copy paper. Magnification = {1-(shift amount/width of sub-scanning)} x 100 Example) When a shift amount is 20 mm and a copy paper is A4, Magnification = {1-(20/210)} x 100 90%
Stopper plate side
Shift amount
4. Setting of shift amount
The shift amount is set by inputting data on the front surface only or by inputting data on the front surface and the rear surface. (1) Press the reduction shift/shift mode button, and select a reduction shift mode or a shift mode. (2) Press a P button. (3) Input the width of an image shift on a front surface by means of the copy quantity setting button (1 to 50 mm). (4) Press a set/F1 button, and finalize. (5) Input the width of an image shift on a rear surface by means of the copy quantity setting button (1 to 50 mm). (6) Press a set/F1 button, and finalize.
a. Use condition (1) It is possible to be used only in an equivalent magnification setting. (2) It is impossible to output on a real time basis. (3) It is impossible to use an super fine mode. (4) An object is an original not having an image shift. (5) In a platen mode, an original stopper plate side is shifted. b. Behavior corresponding to each copy mode Behavior of the shift function changes depending upon a copy mode. For an original not having an image shift, the image shift is prepared. The reduction shift mode is not used for an original having the image shift. · A one side original/one side copy mode An odd number surface Rear edge (Inputting a front data.)
An even number surface Rear edge (Inputting a rear data.) · A one side original/two sides copy mode An odd number surface Rear edge (Inputting a front data.)
An even number surface Front edge (Inputting a rear data.) · A two sides original/one side copy mode An odd number surface Rear edge (Inputting a front data.)
An even number surface Rear edge (Inputting a rear data.) · A two sides original/two sides copy mode An odd number surface Rear edge (Inputting a front data.)
An even number surface Rear edge (Inputting a rear data.)
1 - 15
OPERATION
C
[11] Weekly Timer (Option)
Power for the main body is turned ON or OFF automatically at the time set in advance.
4. Weekly timer setting mode
The weekly timer setting mode is established when a timer setting button is pressed. Procedure 1 Operation Press a timer setting button under a normal mode. When a password is not registered, advance to Item 3. (*1) ENTER PASSWORD
1. Working function
a. ON time monitoring mode Power for the main body is turned ON at the ON time established in advance. (Main body is in the state of OFF.) OFF time monitoring mode Power for the main body is turned OFF at the OFF time established in advance. (Main body is in the state of ON.) Forced starting mode Under the ON time monitoring mode, that mode,is released by a timer releasing button and power for the main body is turned ON. Forced OFF mode Under the OFF time monitoring mode, that mode,is released by a timer releasing button and power for the main body is turned OFF.
b.
c.
2
Input the password with a copy quantity setting button, and press a set/F1 button. ENTER PASSWORD 1234
d.
2. Timer setting function
a. Setting the current time The current time is first set in a form of Year/Month/ Day/Hour/Minute. A day of the week is displayed automatically. Time setting on a timer For each day of the week, ON time and OFF time are set. Setting of the operation day of the week and setting of ON/OFF hours are conducted. Lunch break OFF function The lunch break OFF time is common to all days of the week, and only one lunch break OFF time can be set. Setting operation-designated days ON/OFF setting for the specific day different from the contents registered with setting of the time for a timer is conducted. 3 A menu screen 1 of the weekly timer setting mode appears. (*2) 1 : SETTING TIME 2 : SETTING W. T. ON / OFF 3 : EXIT
b.
c.
d.
(*1) See page 1-20 for the method of registering a password. (*2) When a copy quantity setting button 3 (end) is pressed on a menu screen, it is possible to get out of the weekly timer setting mode.
q Principle of operation buttons
· Copy quantity setting button Data are inputted. · Set/F1 button Data are decided. · Stop/clear button Goes back to a preceding message. · Timer setting button This is used to enter into and to get out of the weekly timer setting mode. · Auto button To get out of the weekly timer setting mode.
3. Conditions of use
a. b. c. d. Machine with a weekly timer The main switch on the main body is in the state of ON. Even when a power cord for the main body is not live, data can be stored. The weekly timer is not allowed to be OFF under the following conditions. · In the course of copying and for 5 minutes after an end · For 5 minutes after operation on the operation panel · Command for prohibition of OFF for main body CPU
1 - 16
OPERATION
5. Setting the current time
This is to set the current time on a year/month/day/hour/ minute basis. Dates from 94/01/01 (January 1, 1994) to 09/ 12/31 (December 31, 2009) can be set. Procedure 1 Operation Call a menu screen 1. 1 : SETTING TIME 2 : SETTING W. T. ON / OFF 3 : EXIT
6. Weekly timer ON/OFF
A mode for setting ON/OFF of a weekly timer is established. Procedure 1 Operation Press a timer setting button to call a menu screen 1. 1 : SETTING TIME 2 : SETTING W. T. ON / OFF 3 : EXIT
2 2 Press a copy quantity setting button 1 (current time setting). INPUT DATE AND PRESS SET
Press a copy quantity setting button 2 (weekly timer ON/OFF). SELECT 1 OR 2 1 : USE 2 : NONUSE 1
14/07/95 14:30 3 3 Input with a copy quantity setting button in the order of year/month/day, and press a set/F1 button. INPUT TIME AND PRESS SET Press a copy quantity setting button 1 (to use), and press a set/F1 button. (*1) Menu screen 2 of the weekly timer ON/OFF setting mode appears. (*2) 1 : TIMER SETTING 2 : LUNCH TIME OFF 3 : HOLIDAY SETTING 4 : EXIT
1 4 / 0 7 / 9 5 ( FRI ) 4
14:30
Input with a copy quantity setting button in the order of hour (24 hours)/minute, and press a set/F1 button.
(*1) At this time, when a copy quantity setting button 2 (not to use) and a set/F1 button are pressed, weekly timer control function can be released. (*2) When a copy quantity setting button 4 (end) is pressed on a menu screen 2, the menu screen 1 is resumed.
SETTING COMPLETION
5
Display is for about 3 seconds, and goes back to the menu screen 1.
1 - 17
OPERATION
7. Timer time setting
How to set the time includes the following two methods. · Collective setting Days from Monday through Friday are set collectively, and Saturday and Sunday are set separately. It is further possible to set each day of the week continuously. · Setting by a day of the week Days from Monday through Sunday are set individually. a. Collective setting Procedure 1 2 3 Operation Press a timer setting button to call a menu screen 1. Press a copy quantity setting button 2 (weekly timer ON/OFF) to call a menu screen 2. Press a copy quantity setting button 1 (to use) and a set/F1 button to call a menu screen 2. 1 : TIMER SETTING 2 : LUNCH TIME OFF 3 : HOLIDAY SETTING 4 : EXIT
Procedure 7
Operation Press a copy quantity setting button 1 (collective) and a set/F1 button to set Monday through Friday collectively. INPUT TIME ( MON ) 0 8 : 3 0 ON TIME FRI ) 1 8 : 0 0 OFFTIME
8
Input ON time for Monday through Friday with a copy quantity setting button in the order of hour (24 hours)/minute, and press a set/F1 button. Successively, input OFF time for Monday through Friday with a copy quantity setting button in the order of hour (24 hours)/minute, and press a set/ F1 button. (*2) INPUT TIME ( SAT ) 0 8 : 3 0 ON TIME 1 8 : 0 0 OFFTIME
9 4 Press a copy quantity setting button (timer time setting). SELECT 1 OR 2
Repeat Item 8 to set ON/OFF time for Saturday and Sunday individually. DAYLY ADJUSTMENT ?
1 : YES 1 : TIMER ( MON ) 5 2 : DAY OFF 1 10 To perform ON/OFF control on a Monday, press the "1" copy quantity setting button (use timer), then press the set/F1 button. To activate the day OFF setting, press the "2" copy quantity button (day OFF), then press the set/F1 button. For Tuesday through Sunday, repeat Item 5. SELECT 1 OR 2 1 : WEEK SET 2 : DAY SET 1
2 : NO
Press a copy quantity setting button 2 (No). (*3)
SETTING COMPLETION
6
11
Display is for about 3 seconds and goes back to the menu screen 2.
(*2) ON/OFF time can be set also on a day cross-over basis. Setting the time earlier than an ON time as an OFF time makes the day cross-over setting. (*3) At this time, when 1 (Yes) is selected, it is possible to set Monday through Sunday individually.
1 - 18
OPERATION
b. Setting by a day of the week Procedures 1 - 6 are the same as those in "a. Collective setting". Procedure 7 Operation Press a copy quantity setting button 2 (each day of the week) and a set/F1 button to set Monday through Sunday individually. INPUT TIME ( MON ) 0 8 : 3 0 ON TIME 1 8 : 0 0 OFFTIME 8 Input ON time for Monday with a copy quantity setting button in the order of hour (24 hours)/ minute, and press a set/F1 button. Successively, input OFF time for Monday with a copy quantity setting button in the order of hour (24 hours)/minute, and press a set/F1 button. (*4) INPUT TIME ( SAT ) 0 8 : 3 0 ON TIME 1 8 : 0 0 OFFTIME
8. Lunch break OFF function
The lunch break OFF time is common to all days of the week, and only one lunch break OFF time can be set. Procedure 1 2 3 Operation Press a timer setting button to call a menu screen 1. Press a copy quantity setting button 2 (weekly timer ON/OFF) to call a menu screen 2. Press a copy quantity setting button 1 (to use) and a set/F1 button to call a menu screen 2. 1 : TIMER SETTING 2 : LUNCH TIME OFF 3 : HOLIDAY SETTING 4 : EXIT 4 Press a copy quantity setting button 2 (lunch break OFF function). SELECT 1 OR 2 1 : USE 1 5 2 : NON USE
9
Repeat Item 8 to set ON/OFF time for Tuesday through Sunday individually.
Press a copy quantity setting button 1 (to use). (*1) INPUT TIME 0 8 : 3 0 OFFTIME 1 3 : 0 0 ON TIME
SETTING COMPLETION 6 10 Display is for about 3 seconds and goes back to the menu screen 2.
(*4) ON/OFF time can be set also on a day cross-over basis. Setting the time earlier than an ON time as an OFF time makes the day cross-over setting.
Input the start time for the lunch break OFF function with a copy quantity setting button in the order of hour (24 hours)/minute, and press a set/ F1 button. Successively, input the end time for the lunch break OFF function with a copy quantity setting button in the order of hour (24 hours)/minute, and press a set/F1 button.
SETTING COMPLETION
7
Display is for about 3 seconds and goes back to the menu screen 2.
(*1) The lunch break OFF function can be released by pressing a copy quantity setting button 2 (not to use).
1 - 19
OPERATION
9. Operation designation day
ON/OFF of the specific day which is different from the contents registered in timer hour setting is set. Procedure 1 2 3 Operation Press a timer setting button to call a menu screen 1. Press a copy quantity setting button 2 (weekly timer ON/OFF) to call a menu screen 2. Press a copy quantity setting button 1 (to use) and a set/F1 button to call a menu screen 2. 1 : TIMER SETTING 2 : LUNCH TIME OFF 3 : HOLIDAY SETTING 4 : EXIT 4 Press a copy quantity setting button 3 (operation designation day). SELECT 1 OR 2 1 : TIMER 2 : DAY OFF 1 4 / 0 7 / 9 5 ( FRI ) 1 5 The specific day which is different from the contents registered in timer hour setting is selected Operation button · Enlargement button: To advance to the following day · Reduction button: To go back to the preceding day · P+enlargement button: To advance to the first day of the following month ·P+reduction button: To go back to the first day of the preceding month SELECT 1 OR 2 1 : TIMER 2 : DAY OFF 1 4 / 0 7 / 9 5 ( FRI ) 1
Procedure 6
Operation When ON/OFF controlling the selected specific day, press a copy quantity setting button 1 (to use a timer). When making the whole day to be OFF, press a copy quantity setting button 2 (whole day OFF). SELECT 1 OR 2 1 : TIMER 2 : DAY OFF 1 4 / 0 7 / 9 5 ( FRI ) 2
7 8
When changing the operation designation day to the other day, repeat Item 5 and 6. After completing the change of the operation designation day fully, press a copy button.
SETTING COMPLETION
9
Display is for about 3 seconds and goes back to the menu screen 2.
1 - 20
OPERATION
10.Forced mode
a. Forced starting mode In the case of OFF made by a weekly timer, power for the main body is turned ON forcedly. Procedure 1 Operation In the case of an ON monitoring mode (main body OFF), press a timer releasing button. When a password is not registered, advance to Item 3. (*1) ENTER PASSWORD
b. Forced OFF mode In this function, it is possible to turn OFF power for the main body without turning off the main switch when a weekly timer is in an OFF time monitoring mode or during the forced starting. Procedure 1 Operation Press a timer releasing button in an OFF monitoring mode (main body ON). OFF THE POWER ? 1 : YES 2 : NO
2 2 Input a password with a copy quantity setting button, and press a set/F1 button. INPUT USAGE TIME THEN PRESS SET 0 3 : HOUR 2 0 : MINUTE
Press a copy quantity setting button 1 (Yes). An ON time monitoring mode is established and power for the main body is turned OFF.
3
Input a period of time to be ON after the forced start in the order of hour/minute, and press a set/ F1 button. PLEASE WAIT WARMING UP
1 4 / 0 7 / 9 5 ( FRI ) 4 5
20:30
After the main body is started, copying is ready. After the established time period has passed, power for the main body is turned OFF to go back to the ON monitoring mode (main body OFF).
(*1) See page 1-20 for the method of registering a password.
1 - 21
OPERATION
11.Setting a password for a weekly timer
A weekly timer function can operate even when a password is not registered. When a password is registered, input of the password is required in the case of setting of a weekly timer and a forced start mode. The password is inputted by a serviceman in a 47-160 mode. (See the adjustment manual.) Procedure 1 Operation 47 mode-code 160 is used for setting. INPUT 4 DIGIT 1234
[12] E.K.C. (Electronic Key Counter) Mode
The present machine is equipped with an E.K.C. function with which an individual user or each group sets a password to control the copy quantity. The E.K.C. mode is divided into a user mode and an operator mode. a. User mode This mode is used to perform a normal copy operation when the E.K.C. has been selected. b. Operator mode The following items to be controlled by E.K.C. are set and confirmed. (1) Setting of a password (256 kinds are registerable) (2) Setting of limit quantity (3) Reading copy count and limit quantity (4) Resetting copy count c. Preparation for using an E.K.C. mode For using an E.K.C. mode, the following settings are necessary. E.K.C. selection (operation setting in the case of limit)
2
A password (4 digits) is inputted with a copy quantity setting button. (*1)
SETTING COMPLETION
(*1)
(*1) Password "0000" is defined to be no setting of a password.
Master key code setting Password/limit quantity setting *1: Operations to be done when a copy count reaches the limit quantity include the following three types. For the method of setting, see "Self-diagnosis/25 mode". Warning only Natural stop When the limit quantity is exceeded, warning is given but copying is possible. When the limit quantity is exceeded in the course of continuous copying, it is prohibited to copy after completion of the copy quantity set. When the limit quantity is exceeded in the course of continuous copying, copying is stopped instantly and it is prohibited to copy. (*2)
Forced stop
*2: For the method of setting, see "Self-diagnosis/25 mode".
1 - 22
OPERATION
1. How to operate an E.K.C. operator mode
(1) Press a copy quantity setting button 9 while pressing a P button. (2) Input the master key code with a copy quantity setting button ENTER YOUR MASTER KEY CODE (3) When the correct master key code is inputted, an E.K.C. operator mode is established. E. T. C. OPERATION MODE (4) Input the numbers of items to be set and confirmed, using a copy quantity setting button, and press a copy button. 1: Setting of a password 2: Setting of a limit quantity 3: Reading of copy count and limit quantity 4: Resetting of copy count (5) Various settings and confirmations (6) Press a stop/clear button to return to the E.K.C. operator mode. (7) Press the stop/clear button while pressing a P button to get out of the E.K.C. operator mode.
2. Password setting
Procedure 1 2 Operation Establish an E.K.C. operator mode. Press a copy quantity setting button 1. 1 : PASSWORD SET
3
Press a copy button. NO. 0 0 1 PASSWORD 0 0 0 0 0
4
Select the registration number with an enlargement button and a reduction button. NO. 0 0 1 PASSWORD 0 0 0 0 0 Registration No.: No. 01 - No. 20
5
Set the password with a copy quantity setting button. NO. 0 0 1 PASSWORD 1 2 3 4 5 Password: 5 digits (Example: 12345)
6 7 8
When registering other passwords, repeat the operations of Items 4 and 5. Return to the E.K.C. operator mode. Succeedingly, conduct other setting or get out of the E.K.C.operator mode.
1 - 23
OPERATION
3. Limit quantity setting
Procedure 1 2 Operation Establish an E.K.C. operator mode. Press a copy quantity setting button 2. 2 : LIMIT COUNT SET
4. Copy count, limit quantity reading
Procedure 1 2 Operation Establish an operator mode. Press a copy quantity setting button 3. 3 : COUNT READOUT
3
Press a copy button. NO. 0 0 1 LIMIT 0 0 0 0 0 0
3
Press a copy button. NO. COUNT / LIMIT 001 0000050/0150000
4
Designate the registration number with an enlargement button and a reduction button. NO. 0 0 3 LIMIT 0 0 0 0 0 0
4
Select the registration number with an enlargement button and a reduction button for confirming copy count and limit. NO. COUNT / LIMIT 001 000050/0150000 (Example: The limit quantity is set to 150,000, and 50 copies have been made.)
5
Set the limit quantity with a copy quantity setting button, and press a copy button. NO. 0 0 3 LIMIT 0 1 5 0 0 0 0 Maximum quantity to be set: 999,999 sheets (Example: 25,000 sheets) 5 6 7
When confirming other registration numbers, repeat the operations of Item 4. Return to the E.K.C. operator mode. Succeedingly, conduct other setting or get out of the E.K.C. operator mode.
6 7 8
When setting other limit quantities, repeat the operation of Item 4 and 5. Return to the E.K.C. operator mode. Succeedingly, conduct other setting or get out of the E.K.C. operator mode.
1 - 24
OPERATION
5. Resetting copy count
Resetting of copy count includes the following two types. (1) All reset (2) Individual reset a. All reset All counts are reset collectively. Procedure 1 2 Operation Establish an E.K.C.operator mode. Press a copy quantity setting button 4. 4 : COUNTER RESET
b. Individual reset Specific registration numbers are reset. Procedure 1 2 Operation Establish an E.K.C.operator mode. Press a copy quantity setting button 4. 4 : COUNTER RESET
3
Press a copy button. CLEAR ALL COUNTERS YES / NO ?
3
Press a copy button. (See *1.) CLEAR ALL COUNTERS YES / NO ?
4
Press a stop/clear button. NO. 0 0 1 : COUNT CLEAR YES / NO ?
4
Press a copy button. CLEAR ALL COUNTERS ! !
5
Select the registration number to be reset with an enlargement button and a reduction button, and press a copy button. NO. 0 0 7 : COUNT CLEAR
5 6
Return to the E.K.C. operator mode. Succeedingly, conduct other setting or get out of the E.K.C.operator mode. 6 7 8 When clearing other registration numbers, repeat the operation of Item 5. Return to the E.K.C. operator mode. Succeedingly, conduct other setting or get out of the E.K.C.operator mode.
*1: When canceling the reset of copy count (in the case of "NO"), press a stop/clear button twice to go back to the operator mode.
1 - 25
OPERATION
[13] Auto Shut Off Setting
When operations of an operation panel and copying are not executed for a certain period of time, all display LEDs on the operation panel are turned off. This time period is set in "Adjustment manual/25 mode". 0: 1: 2: 3:
C
None 2 minutes 6 minutes 10 minutes
Note: Also valid in pre-heating mode.
[14] Auto Reset
When operations of an operation panel and copying are not executed for a certain period of time, the main body is returned to its initial state. This time period is set in "Adjustment manual/ 25 mode". 0: 1: 2:
C
None 1.5 minutes 1.5 minutes
Note: Also valid in pre-heating mode. Initial state Display Copy quantity ADF APS AE 1:1 Sorter Paper size Magnification Magnification mode Copy density Specific function Sort/group Paper feed location State 1 Flashing (in the case of auto priority mode) Lighting (in the case of auto priority mode) Lighting (in the case of auto priority mode) Lighting Lighting (in the case of auto priority mode) Lighting of all sixes of papers set 1.00 Fixed lighting Light-out (in the case of auto priority mode) Light-out (in the case of auto priority mode) Sort lighting (in the case of sorter priority mode) All paper feed locations for set papers lighting
1 - 26
OPERATION
COUNT NUMBER CONFIRMATION
[1] PM Count
1. Press a copy quantity setting button 5 while pressing a P button. 2. A PM count number is displayed on a message display. 3. For the method of resetting, see "Setting and confirmation by Adjustment manual/P function".
[2] Drum Count
1. Press a copy quantity setting button 7 while pressing a P button. 2. A drum count number is displayed on a message display. Also on a copy quantity display, the number is indicated by being divided into three each including 2 digits from the higher position. (Example) The number of the drum count is 12345.
0 1 Initial value
2 3
4 5 Initial value
10000's 100's 10's1's 1000's
3. For the method of resetting, see "Adjustment manual/ setting and confirmation by P function".
1 - 27
OPERATION
MESSAGE LIST
Messages in the table below are displayed on a message indicator of the present machine, depending on the conditions of the machine.
1. Each symbol in the table means as follows.
(1) "N" in the column of types indicates that the machine keeps displaying the same message until the machine enters its another state. (2) "S" in the column of types is a temporary display which lasts for 3 seconds. (3) "NS" in the column of types means a display in combination with other messages. (4) "A" in the column of types indicates that two messages are displayed alternately. (5) "AN" in the column of types indicates that the machine keeps displaying the same message until the machine enters its another state.
[1] Bases
No. 1-1 1-2 1-3 1-4 1-5 Types N N N N N Under warm-up Ready for copy Under copying In process of auto shut off Under pre-heating mode Machine state Message PLEASE WAIT WARMING UP READY TO COPY COPYING STANDBY MODE PRESS ANY KEY
[2] Warning
1. Main body
No. 2-1-1 2-1-2 2-1-3 2-1-4 2-1-5 2-1-6 2-1-7 2-1-8 2-1-9 N N N N Under PFU, or the state of no paper in 1500-sheet LCT tray Key counter OFF (for coping with a convenience store) Card OFF (for coping with a convenience store) Coin OFF (for coping with a convenience store) Types N NS NS NS Machine state No paper for by-pass feed (after stop with no paper) Toner empty Toner empty PM count over (periodic inspection) ROUTINE SERVICE REQD PLEASE SELECT COPY QUANTITY PLEASE SUPPLY PAPER IN DRAWER [ 4 ] PLEASE INSERT KEY COUNTER Message PLEASE SUPPLY PAPER IN BYPASS TRAY READY TO COPY PLEASE SUPPLY TONER COPYING PLEASE SUPPLY TONER
1 - 28
OPERATION
No. 2 - 1 - 10 2 - 1 - 11 2 - 1 - 12 2 - 1 - 13 2 - 1 - 14 2 - 1 - 15 2 - 1 - 16 2 - 1 - 17 2 - 1 - 18 2 - 1 - 19 2 - 1 - 20 2 - 1 - 21 2 - 1 - 22 2 - 1 - 23 2 - 1 - 24 2 - 1 - 25 2 - 1 - 26 2 - 1 - 27 2 - 1 - 28 2 - 1 - 29
Types N N N S N N N S
Machine state No selected tray [A4R] Tray is set neither on the main body nor on a PFU. Paper is set neither on upper tray nor on lower tray in main body and PFU. No corresponding size in APS No paper in tray (after stop with no paper) No tray, or no 1500-sheet LCT tray 8 x 13 size DATA When a magnification button or an enlargement/reduction button is pressed in an image shift copy mode Memory card OFF in the machine with a memory card 8 x 13/F4 INSERT
Message [A4] DRAWERIF REQUIRED PLEASE INSERT A DRAWER PLEASE SUPPLY PAPER PLEASE SUPPLY [ A 4 R ] PAPER
RE NOT AVAILABLE IN IMAGE SHIFT MODE PLEASE INSERT MEMORY CARD PLEASE COLOSE TOP RIGHT SIDE COVER PLEASE CLOSE LEFT SIDE COVER PLEASE CLOSE BOTTOM RIGHT SIDE COVER FRONT DOOR IS OPEN PLEASE CLOSE PLEASE EMPTY DUPLEX TRAY THIS CARD IS UNACCEPTABLE
N N N N
On the occasion of occurrence of P 17. On the occasion of occurrence of P 33. On the occasion of occurrence of P 18 and P 19. On the occasion of occurrence of P 51.
Over loading on LCT S S When a copy button is pressed with two sides selected under indeterminate form of upper tray in by-pass feed When a copy button is pressed with B6 size and two sides selected On the occasion of occurrence of E (error requiring power OFF) When trying to select a prohibited function
WITHDRAW [ 3 ] TRAY REDUCE PAPER DUPLEX UNAVAILABLE IN BYPASS / IRREGULAR DUPLEX UNAVAILABLE IN 5 . 5 x 8 . 5 SIZE PLEASE SW ON / OFF [4701] [ UNAVAIL : PLATEN MEM. ] [ SELECTING 2 IN 1 ]
1 - 29
OPERATION
No. 2 - 1 - 30
Types
Machine state On the occasion of memory overflow (when completing a part in the case of real time output) When it is impossible to recover under a look-ahead mode MEMORY FULL
Message
2 - 1 - 31
In the case of memory overflow (under no page change in a two-sided original/duplex copy mode) Alternating display of "OVR3"
MEMORY FULL
2 - 1 - 32
In the case of memory overflow (under no page change in a two-sided original/duplex copy mode) Alternating display of "OVR2"
PRESS START TO COPY STORED IMAGES ONLY ALIGN REMAINING ORIGINALS MEMORY FULL PRESS CLR TO CLR
2 - 1 - 33 2 - 1 - 34
After memory over, when completing output for what has been read
2. ADF
No. 2-2-1 2-2-2 2-2-3 2-2-4 2-2-5 2-2-6 N N N ADF mode, after clearing jam in the main body A cover for RADF reversal section is opened. Singular number expression of ADF 3 message (ADF 3 is singular/plural number and wording is different) PLEASE CLOSE DOCUMENT FEEDER Types N Machine state No original is set on ADF (ADF mode) Message PLEASE INSERT ORIGINALFACE DOWN REMOVE AND RELOAD ORIGINALS RELOAD [ 2 ] ORIG FACE DOWN PRESS PRINT PLEASE CLOSE RADF REVERSING UNIT COVER
3. Finisher
No. 2-3-1 2-3-2 2-3-3 2-3-4 2-3-5 2-3-6 Types S S A A A N Machine state When the set quantity exceeds the limit in a sort mode When the set quantity exceeds the limit in a group mode On the occasion of occurrence of P 71. On the occasion of occurrence of P 71. On the occasion of occurrence of P 71. Under operation of a sorter Message MAX. [ 2 5 ] COPIES IN SORT MODE MAX. [ 1 0 ] COPIES IN GROUP MODE PLEASE CLOSE SORTER ENTRANCE COVER PLEASE CONNECT SORTER TO THE COPIER PLEASE CLOSE SORTER UPPER / ENTRANCE COVER PLEASE WAIT SORTER BINS MOVING
1 - 30
OPERATION
No. 2-3-7 2-3-8 2-3-9 2 - 3 - 10 2 - 3 - 11 2 - 3 - 12 2 - 3 - 13 2 - 3 - 14 2 - 3 - 15 2 - 3 - 16 2 - 3 - 17 2 - 3 - 18
Types S A S S A S
Machine state When no staple is detected under stapling operation On the occasion of occurrence of P 99. When the effective number of sheet for stapling is exceeded When sizes of papers to be stapled are not the same On the occasion of occurrence of P 99. When the staple cartridge is not inserted surely
Message OPEN STAPLER DOOR SUPPLY STAPLES PLEASE REMOVE COPIES FROM SORTER STAPLEMAX. [ 2 5 ] SHEETS PLEASE REDUCE / REMOVE STAPLER UNAVAILABLE PLEASE REMOVE PAPER OPEN STAPLER DOOR AND RELOAD STAPLER OPEN STAPLER DOOR AND CHECK STAPLER PLEASE CLOSE FINISHER COVRE CONNECT FINISHER TO THE COPIER PLEASE WAIT FINISHER MOVING PLEASE REMOVE COPIES FROM THE FINISHER STAPLING UNAVAILABLE WITH [ BYPASS ] STAPLE MAX [ 2 5 ] COPIES
4. ADU
No. 2-4-1 2-4-2 2-4-3 2-4-4 2-4-5 Types N N NS NS A mode is started When the number of sheets set is "0" Right side in the case of duplex copying Reverse side in the case of duplex copying When the size prohibited in a duplex copy mode is selected and a copy button is pressed in the duplex copy mode (in process of display of "P.97") 2-4-6 S When a size button is pressed on the half way of a duplex copy mode PAPER SIZE CANNOT BE CHANGED NOW Machine state When paper exists on a stacker before the duplex copy Message PLEASE EMPTY DUPLEX TRAY PLEASE SELECT COPY QUANTITY SIDE 1 SIDE 2 PLEASE SELECT PAPER SIZE FROM DRAWERS
1 - 31
OPERATION
No. 2-4-7 2-4-8
Types S N
Machine state When a copy quantity setting button is pressed on the half way of the duplex copy mode On the occasion of occurrence of P 91.
Message COPY QUANTITY CANNOT BE CHANGED NOW PLEASE RESET DUPLEX UNIT
[3] Interruption Copy
No. 3-1 3-2 3-3 Types S N S Machine state When the machine is in an interruption mode In process of interruption copying When the machine is restored from an interruption mode Message COPYING INTERRUPTED COPY INTERRUPT IN PROGRESS COPY INTERRUPT IS COMPLETED
[4] P Function
No. 4-1 4-2 4-3 4-4 4-5 4-6 4-7 4-8 4-9 4 - 10 4 - 11 4 - 12 Types A S S S N N S A N N N S Machine state Under an arbitrary magnification setting mode P+ magnification button P+1 P+5 When a frame erasure mode is selected Under a frame