Text preview for : hfe_aiwa_csd-td31_td32_service_en.pdf part of Aiwa CSD-TD31 CSD-TD32 COMPACT DISC STEREO RADIO CASSETTE RECORDER Service Manual
BASIC TAPE MECHANISM : TN-21ZVC-2000
BASIC CD MECHANISM : DA11T3C
Back to : hfe_aiwa_csd-td31_td32_se | Home
CSD-TD31 LHS US
CSD-TD32 UW
SERVICE MANUAL
COMPACT DISC STEREO RADIO BASIC TAPE MECHANISM : TN-21ZVC-2000
CASSETTE RECORDER BASIC CD MECHANISM : DA11T3C
TA
DA
S/M Code No. 09-003-342-8N1
SPECIFICATIONS
· Design and specifications are subject to change without
notice .
ACCESSORIES/PACKAGE LIST
REF. NO PART NO. KANRI DESCRIPTION
NO.
1 8A-CHB-902-010 IB,LH(ESP)FM<1LH>
1 8A-CHB-903-010 IB,U(ESF)FM<2UW,1US>
! 2 87-A80-036-010 AC CORD SET ASSY,E W/FLTR VOL
<1LH>
! 2 87-A80-109-010 AC CORD,HK7281 BLK U<2UW,1US>
! 3 87-A91-017-010 PLUG,CONVERSION JT-0476<1LH>
2
PROTECTION OF EYES FROM LASER BEAM DURING SERVICING
This set employs laser. Therefore, be sure to follow carefully the CAUTION
instructions below when servicing. Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous
WARNING! radiation exposure.
WHEN SERVICING, DO NOT APPROACH THE LASER EXIT
WITH THE EYE TOO CLOSELY. IN CASE IT IS NECESSARY TO ATTENTION
CONFIRM LASER BEAM EMISSION. BE SURE TO OBSERVE L'utilisation de commandes, réglages ou procédures autres que
FROM A DISTANCE OF MORE THAN 30cm FROM THE ceux spécifiés peut entraîner une dangereuse exposition aux
SURFACE OF THE OBJECTIVE LENS ON THE OPTICAL radiations.
PICK-UP BLOCK.
ADVARSEL!
Caution: Invisible laser radiation when
Usynlig laserståling ved åbning, når sikkerhedsafbrydereer ude
open and interlocks defeated avoid expo-
af funktion. Undgå udsættelse for stråling.
sure to beam.
Advarsel:Usynling laserståling ved åbning,
This Compact Disc player is classified as a CLASS 1 LASER
når sikkerhedsafbrydere er ude af funktion.
product.
Undgå udsættelse for stråling.
The CLASS 1 LASER PRODUCT label is located on the rear
exterior.
VAROITUS!
Laiteen Käyttäminen muulla kuin tässä käyttöohjeessa mainit-
ulla tavalla saattaa altistaa käyt-täjän turvallisuusluokan 1 ylit-
CLASS 1 LASER PRODUCT
tävälle näkymättömälle lasersäteilylle. KLASSE 1 LASER PRODUKT
LUOKAN 1 LASER LAITE
KLASS 1 LASER APPARAT
VARNING!
Om apparaten används på annat sätt än vad som specificeras i
denna bruksanvising, kan användaren utsättas för osynling
laserstrålning, som överskrider gränsen för laserklass 1.
Precaution to replace Optical block PICK-UP Assy P.C.B
(SF-P101NR)
Body or clothes electrostatic potential could ruin
laser diode in the optical block. Be sure ground
body and workbench, and use care the clothes
do not touch the diode.
1) After the connection, remove solder shown in
the right figure.
Solder
3
ELECTRICAL MAIN PARTS LIST
REF. NO PART NO. KANRI DESCRIPTION REF. NO PART NO. KANRI DESCRIPTION
NO. NO.
IC C321 87-010-197-080 CAP, CHIP 0.01 DM
C322 87-010-263-080 CAP, ELECT 100-10V
87-A21-550-010 IC,TA2149N C325 87-010-405-080 CAP, ELECT 10-50V
87-A21-185-040 C-IC,LC72121M C401 87-010-403-080 CAP, ELECT 3.3-50V
87-A21-064-010 IC,LA4227 C402 87-010-197-080 CAP, CHIP 0.01 DM
87-A21-520-040 C-IC,M61509FP
87-A20-446-010 C-IC,LA9241ML C403 87-010-263-080 CAP, ELECT 100-10V
C404 87-010-248-080 CAP, ELECT 220-10V
87-A20-459-010 C-IC,LC78622ED C405 87-010-197-080 CAP, CHIP 0.01 DM
87-A21-093-010 IC,LA6541D C406 87-010-374-080 CAP, ELECT 47-10V
8A-CH4-661-010 C-IC,LC867132V-5P07 C407 87-010-178-080 CHIP CAP 1000P
87-A21-431-010 IC,BA4560N
C408 87-010-198-080 CAP, CHIP 0.022
C409 87-010-248-080 CAP, ELECT 220-10V
TRANSISTOR C410 87-010-263-080 CAP, ELECT 100-10V
C411 87-A11-177-080 C-CAP,S 0.15-16 K B
89-327-143-080 TR,2SC2714 (0.1W) C412 87-010-401-080 CAP, ELECT 1-50V
87-026-447-080 TR,2SC1740S R
89-111-624-080 TR,2SA1162Y C413 87-016-369-080 C-CAP,S 0.033-25 B K
87-026-213-080 CHIP-TR,DTC114YK C414 87-010-405-080 CAP, ELECT 10-50V
89-320-011-080 TR,2SC2001 (15W) C416 87-010-545-080 CAP, ELECT 0.22-50V
C417 87-012-157-080 C-CAP,S 330P-50 CH
89-327-125-080 C-TR,2SC2712(GR) C418 87-010-213-080 C-CAP,S 0.015-50 B
89-112-965-080 TR,2SA1296 (0.75W)
87-026-463-080 TR,2SA933S (0.3W) C419 87-A11-608-080 C-CAP,S 0.33-25 K B
87-026-291-080 TR,DTC124XS C420 87-016-369-080 C-CAP,S 0.033-25 B K
87-A30-226-010 TR,2SB1655E C421 87-A11-177-080 C-CAP,S 0.15-16 K B
C422 87-010-184-080 CHIP CAPACITOR 3300P(K)
87-026-462-080 TR,2SC1740 S(RS 0.3W) C423 87-010-194-080 C-CAP,S 0.47-25V(Z)F
89-318-154-080 TR,2SC1815 (0.4W)
89-109-332-380 TR,2SA933RS C424 87-A10-712-080 C-CAP,S 0.22-25V(Z)F
89-113-187-080 TR,2SA1318TU C425 87-010-176-080 C-CAP,S 680P-50 SL
87-026-239-080 TR,DTC114TK (0.2W) C426 87-A11-608-080 C-CAP,S 0.33-25 K B
C428 87-010-197-080 CAP, CHIP 0.01 DM
87-026-210-080 C-TR, DTC144EK C429 87-010-186-080 CAP,CHIP 4700P
87-026-464-080 TR,DTC114TS (0.3W)
C430 87-012-156-080 C-CAP,S 220P-50 CH
C431 87-010-545-080 CAP, ELECT 0.22-50V
DIODE C432 87-010-374-080 CAP, ELECT 47-10V
C433 87-010-401-080 CAP, ELECT 1-50V
87-070-345-080 DIODE,IN4148 C434 87-010-184-080 CHIP CAPACITOR 3300P(K)
87-A40-616-070 VARI-CAP,SVC384(S/T)
87-A40-128-080 C-VARI-CAP,HVU202A C435 87-010-197-080 CAP, CHIP 0.01 DM
87-017-072-080 ZENER,HZS3B1 C436 87-010-374-080 CAP, ELECT 47-10V
87-027-399-080 ZENER,HZ7A3L (200MA)<2UW,1US> C437 87-010-404-080 CAP, ELECT 4.7-50V
C438 87-016-669-080 C-CAP,S 0.1-25 K B
87-027-607-080 ZENER,HZ7B3L<1LH> C439 87-010-178-080 CHIP CAP 1000P
87-A40-648-080 ZENER,MTZJ8.2A
87-A40-234-080 ZENER,MTZJ5.6A C440 87-010-145-080 C-CAP,S 1P-50 CH
87-017-978-080 DIODE,1N4003 C441 87-010-197-080 CAP, CHIP 0.01 DM
87-027-702-080 ZENER,HZ6C2L C442 87-010-312-080 C-CAP,S 15P-50 CH
C445 87-012-368-080 C-CAP,S 0.1-50 F
87-020-465-080 DIODE,1SS133 (110MA) C446 87-012-368-080 C-CAP,S 0.1-50 F
87-A40-465-010 DIODE,FR202
C447 87-012-368-080 C-CAP,S 0.1-50 F
C448 87-010-315-080 C-CAP,S 27P-50 CH
MAIN C.B C450 87-012-140-080 CAP 470P
C451 87-012-156-080 C-CAP,S 220P-50 CH
C30 87-010-260-080 CAP, ELECT 47-25V C455 87-010-247-080 CAP, ELECT 100-50V
C251 87-010-401-080 CAP, ELECT 1-50V
C261 87-010-402-080 CAP, ELECT 2.2-50V C457 87-010-312-080 C-CAP,S 15P-50 CH
C262 87-010-402-080 CAP, ELECT 2.2-50V C458 87-010-312-080 C-CAP,S 15P-50 CH
C263 87-010-178-080 CHIP CAP 1000P C459 87-010-263-080 CAP, ELECT 100-10V
C460 87-015-819-080 CAPACITOR,0.01
C264 87-010-178-080 CHIP CAP 1000P C461 87-010-197-080 CAP, CHIP 0.01 DM
C265 87-010-263-080 CAP, ELECT 100-10V
C266 87-010-263-080 CAP, ELECT 100-10V C462 87-010-248-080 CAP, ELECT 220-10V
C267 87-010-112-080 CAP, ELECT 100-16V C463 87-010-197-080 CAP, CHIP 0.01 DM<2UW,1US>
C268 87-010-112-080 CAP, ELECT 100-16V C463 87-010-190-080 S CHIP F 0.01<1LH>
C465 87-010-404-080 CAP, ELECT 4.7-50V
C271 87-010-221-080 CAP, ELECT 470-10V C466 87-012-368-080 C-CAP,S 0.1-50 F
C272 87-010-221-080 CAP, ELECT 470-10V
C278 87-010-405-080 CAP, ELECT 10-50V C467 87-010-263-080 CAP, ELECT 100-10V
C279 87-010-385-080 CAP, ELECT 220-25V C469 87-012-154-080 C-CAP,S 150P-50 CH
C301 87-016-495-000 EL CAP 3300UF/25V C470 87-010-544-080 CAP, ELECT 0.1-50V
C471 87-015-785-080 CHIP CAPACITOR, 0.1FZ-25Z
C306 87-010-404-080 CAP, ELECT 4.7-50V C472 87-015-785-080 CHIP CAPACITOR, 0.1FZ-25Z
C307 87-010-401-080 CAP, ELECT 1-50V
C308 87-010-221-080 CAP, ELECT 470-10V C473 87-015-785-080 CHIP CAPACITOR, 0.1FZ-25Z
C311 87-010-263-080 CAP, ELECT 100-10V C474 87-015-785-080 CHIP CAPACITOR, 0.1FZ-25Z
C312 87-010-385-080 CAP, ELECT 220-25V C475 87-010-197-080 CAP, CHIP 0.01 DM
C476 87-010-236-080 CAP,E 1000-10 SME
C477 87-010-197-080 CAP, CHIP 0.01 DM
4
REF. NO PART NO. KANRI DESCRIPTION REF. NO PART NO. KANRI DESCRIPTION
NO. NO.
C478 87-010-263-080 CAP, ELECT 100-10V C823 87-010-178-080 CHIP CAP 1000P
C479 87-010-197-080 CAP, CHIP 0.01 DM C824 87-010-178-080 CHIP CAP 1000P
C480 87-010-221-080 CAP, ELECT 470-10V C829 87-010-178-080 CHIP CAP 1000P
C481 87-010-405-080 CAP, ELECT 10-50V C830 87-010-178-080 CHIP CAP 1000P
C482 87-010-405-080 CAP, ELECT 10-50V C833 87-018-195-080 CAP, CER 1200P-16V
C489 87-012-368-080 C-CAP,S 0.1-50 F C834 87-010-248-080 CAP, ELECT 220-10V
C490 87-012-368-080 C-CAP,S 0.1-50 F C835 87-010-322-080 C-CAP,S 100P-50 CH
C491 87-010-197-080 CAP, CHIP 0.01 DM C836 87-010-322-080 C-CAP,S 100P-50 CH
C492 87-010-221-080 CAP, ELECT 470-10V C843 87-010-197-080 CAP, CHIP 0.01 DM
C494 87-010-197-080 CAP, CHIP 0.01 DM<2UW,1US> C844 87-018-124-080 CAP, CER 270P-50V
C494 87-010-190-080 S CHIP F 0.01<1LH> C845 87-010-178-080 CHIP CAP 1000P
C501 87-012-368-080 C-CAP,S 0.1-50 F C846 87-010-263-080 CAP, ELECT 100-10V
C502 87-010-322-080 C-CAP,S 100P-50 CH C851 87-010-186-080 CAP,CHIP 4700P
C503 87-010-322-080 C-CAP,S 100P-50 CH C852 87-010-178-080 CHIP CAP 1000P
C504 87-010-322-080 C-CAP,S 100P-50 CH C853 87-A11-145-080 CAP,TC U 0.01-50 Z F
C505 87-010-322-080 C-CAP,S 100P-50 CH CN201 87-099-018-010 CONN,16P
C506 87-010-322-080 C-CAP,S 100P-50 CH CN801 87-A60-110-010 CONN,4P V S2M-4W
C510 87-016-669-080 C-CAP,S 0.1-25 K B CNA302 8A-CDB-627-010 CONN ASSY,6P MA-TUNER
C831 87-010-198-080 CAP, CHIP 0.022 L801 87-007-342-010 COIL,OSC 85K BIAS
CN202 8A-CH4-689-010 CONN BASE 3P 2.5mm SW801 88-CT6-619-010 BACK SLIDE SW 6P2T SHORTIN
CN205 87-A60-109-010 CONN,2P V S2M-2W
CN301 87-099-416-010 CONN,3P EH H WHT FRONT C.B
CN401 87-A60-424-010 CONN,16P V TOC-B
CN403 87-099-201-010 CONN,8P 6216 H C601 87-010-313-080 CAP, CHIP 18P
CN802 87-049-469-010 CONN,4P V C602 87-010-315-080 C-CAP,S 27P-50 CH
C603 87-010-319-080 C-CAP,S 56P-50 CH
CNA402 8A-CDB-622-010 CONN ASSY,6P CD-MOTOR C604 87-010-312-080 C-CAP,S 15P-50 CH
L401 87-003-102-080 COIL, 10UH C605 87-010-317-080 C-CAP,S 39P-50 CH
L404 87-003-152-080 COIL, 100UH
!R840 87-029-124-010 RES,FUSE 2.2-1/4 C606 87-015-785-080 CHIP CAPACITOR, 0.1FZ-25Z
SFR430 87-024-437-080 SFR100K,RH063EC C607 87-010-196-080 CHIP CAPACITOR,0.1-25
C608 87-010-196-080 CHIP CAPACITOR,0.1-25
X401 8Z-CD5-633-010 VIB, CER16.93MHZ FCR16.93M2 C610 87-010-555-040 CAP,E 100-10 GAS
C611 87-010-196-080 CHIP CAPACITOR,0.1-25
TAPE C.B C612 87-A10-189-040 CAP,E 220-10
C613 87-010-495-040 CAP,E 2.2-50 GAS
C211 87-010-805-080 CAP, S 1-16 C614 87-010-196-080 CHIP CAPACITOR,0.1-25
C212 87-010-805-080 CAP, S 1-16 C615 87-010-493-040 CAP,E 0.47-50 GAS
C215 87-016-460-080 C-CAP,S 0.22-16 B C616 87-010-494-040 CAP,E 1-50 GAS
C216 87-016-460-080 C-CAP,S 0.22-16 B
C231 87-010-213-080 C-CAP,S 0.015-50 B C620 87-010-555-040 CAP,E 100-10 GAS
C625 87-010-197-080 CAP, CHIP 0.01 DM
C232 87-010-213-080 C-CAP,S 0.015-50 B C661 87-010-498-040 CAP,E 10-16 GAS
C233 87-A10-201-080 C-CAP,S0.33-16 KB CN601 87-099-033-010 16P 6216 H
C234 87-A10-201-080 C-CAP,S0.33-16 KB CN602 87-099-201-010 CONN,8P 6216 H
C235 87-016-669-080 C-CAP,S 0.1-25 K B
C236 87-016-669-080 C-CAP,S 0.1-25 K B CNA603 8A-CHB-616-010 CONN ASSY,4P TU-FR(DIGITAL)
CNA604 8A-CHB-617-010 CONN ASSY,2P VOL-KEY
C237 87-010-408-080 CAP, ELECT 47-50V CNA606 8A-CHB-621-010 CONN ASSY,8P FUNCT-KEY
C239 87-010-197-080 CAP, CHIP 0.01 DM L601 87-003-171-010 COIL,15UH TROIDAL
C240 87-010-197-080 CAP, CHIP 0.01 DM LCD601 8A-CHB-625-010 LCD,HLC7107ACH-11
C247 87-010-401-080 CAP, ELECT 1-50V
C248 87-010-401-080 CAP, ELECT 1-50V LED602 88-CD6-630-010 LED,934ID RED
LED603 88-CD6-630-010 LED,934ID RED
C309 87-010-197-080 CAP, CHIP 0.01 DM LED604 88-CD6-630-010 LED,934ID RED
C310 87-010-248-080 CAP, ELECT 220-10V LED608 88-CD6-630-010 LED,934ID RED
C316 87-010-384-080 CAP, ELECT 100-25V S601 8Z-CT6-636-010 SW,TACT EVQJAC04M
C483 87-012-156-080 C-CAP,S 220P-50 CH
C484 87-012-156-080 C-CAP,S 220P-50 CH S604 8Z-CT6-636-010 SW,TACT EVQJAC04M
S605 8Z-CT6-636-010 SW,TACT EVQJAC04M
C801 87-010-248-080 CAP, ELECT 220-10V S606 8Z-CT6-636-010 SW,TACT EVQJAC04M
C805 87-012-365-080 C-CAP,S 0.027-25VBK S607 8Z-CT6-636-010 SW,TACT EVQJAC04M
C806 87-012-365-080 C-CAP,S 0.027-25VBK X601 87-030-273-010 VIB,XTAL 32.768K5PPM
C807 87-010-405-080 CAP, ELECT 10-50V
C808 87-010-405-080 CAP, ELECT 10-50V X602 87-030-376-080 VIB,CER CSA5.76MG200
C809 87-010-405-080 CAP, ELECT 10-50V
C810 87-010-405-080 CAP, ELECT 10-50V TU C.B
C811 87-010-178-080 CHIP CAP 1000P
C812 87-010-178-080 CHIP CAP 1000P C1 87-010-314-080 C-CAP,S 22P-50V
C816 87-010-180-080 C-CER 1500P C2 87-010-316-080 C-CAP,S 33P-50 CH
C3 87-010-314-080 C-CAP,S 22P-50V
C817 87-010-180-080 C-CER 1500P C5 87-016-669-080 C-CAP,S 0.1-25 K B
C819 87-010-426-080 C-CAP,S 0.012-25 B C6 87-010-313-080 CAP, CHIP 18P
C820 87-010-426-080 C-CAP,S 0.012-25 B
C821 87-010-401-080 CAP, ELECT 1-50V C7 87-014-049-080 CAP,PP 470P-100 J
C822 87-010-401-080 CAP, ELECT 1-50V C8 87-012-349-080 C-CAP,S 1000P-50 CH
C10 87-010-197-080 CAP, CHIP 0.01 DM
5
REF. NO PART NO. KANRI DESCRIPTION REF. NO PART NO. KANRI DESCRIPTION
NO. NO.
C11 87-010-197-080 CAP, CHIP 0.01 DM HLD1 88-CD6-661-010 HLDR,BAR ANT.
C12 87-010-197-080 CAP, CHIP 0.01 DM HLD2 88-CD6-661-010 HLDR,BAR ANT.
C13 87-010-150-080 C-CAP,S 6P-50 CH L2 87-A50-560-010 COIL,FM BPF(ACD)
C14 87-010-303-080 C-CAP,S 330P-50CH L3 8A-CH4-670-010 BAR-ANT,MW 2B-ACH(COI)
C15 87-012-349-080 C-CAP,S 1000P-50 CH L4 87-A50-420-010 COIL,MW OSC(SYN)
C16 87-010-374-080 CAP, ELECT 47-10V L5 87-A50-566-010 COIL,FM RF EX(ACH)
C17 87-010-198-080 CAP, CHIP 0.022 L6 87-A50-568-010 COIL,FM OSC EX(ACH)
C18 87-015-835-080 C-CAP,0.047 D L7 87-A91-308-010 FLTR,PCFAZH- 450T (TOK)
C19 87-010-263-080 CAP, ELECT 100-10V L8 87-005-849-080 COIL,10UH(CECS)
C20 87-010-404-080 CAP, ELECT 4.7-50V TC1 87-011-254-080 TRIMER,20P LAR
C21 87-010-197-080 CAP, CHIP 0.01 DM X1 87-A70-061-010 VIB,XTAL 4.500MHZ CSA-309
C22 87-010-197-080 CAP, CHIP 0.01 DM
C23 87-010-197-080 CAP, CHIP 0.01 DM
C25 87-016-460-080 C-CAP,S 0.22-16 B HP C.B
C26 87-018-131-080 CAP, CER 1000P-50V
CN203 87-049-469-010 CONN,4P V
C27 87-A11-067-080 C-CAP,S 1-10 K B J251 87-009-216-010 JACK, DIA 3.5
C28 87-016-669-080 C-CAP,S 0.1-25 K B
C29 87-016-669-080 C-CAP,S 0.1-25 K B
C30 87-010-198-080 CAP, CHIP 0.022 LED C.B
C31 87-010-198-080 CAP, CHIP 0.022
CN607 87-009-236-010 CONN 8P PH H
C33 87-A11-729-080 C-CAP,0.47-16V Y5V LED605 88-CD6-630-010 LED,934ID RED
C34 87-A11-729-080 C-CAP,0.47-16V Y5V LED606 88-CD6-630-010 LED,934ID RED
C35 87-015-819-080 CAPACITOR,0.01 LED611 88-CD6-631-010 LED,934GD GRN
C36 87-010-263-080 CAP, ELECT 100-10V S608 8Z-CT6-636-010 SW,TACT EVQJAC04M
C37 87-010-197-080 CAP, CHIP 0.01 DM
S609 8Z-CT6-636-010 SW,TACT EVQJAC04M
C38 87-010-374-080 CAP, ELECT 47-10V S610 8Z-CT6-636-010 SW,TACT EVQJAC04M
C39 87-010-404-080 CAP, ELECT 4.7-50V S611 8Z-CT6-636-010 SW,TACT EVQJAC04M
C40 87-010-197-080 CAP, CHIP 0.01 DM S613 8Z-CT6-636-010 SW,TACT EVQJAC04M
C41 87-012-349-080 C-CAP,S 1000P-50 CH
C42 87-012-349-080 C-CAP,S 1000P-50 CH
VOL C.B
C43 87-012-349-080 C-CAP,S 1000P-50 CH
C44 87-010-311-080 CAP 12P CN608 84-722-632-010 CONN,2P H
C45 87-010-312-080 C-CAP,S 15P-50 CH S614 8Z-CT6-636-010 SW,TACT EVQJAC04M
C46 87-010-197-080 CAP, CHIP 0.01 DM S615 8Z-CT6-636-010 SW,TACT EVQJAC04M
C47 87-010-197-080 CAP, CHIP 0.01 DM
C48 87-010-197-080 CAP, CHIP 0.01 DM PWR C.B
C49 87-012-140-080 CAP 470P
C50 87-010-197-080 CAP, CHIP 0.01 DM C901 87-018-205-080 CAP, CERA-SOL 0.022
C71 87-010-197-080 CAP, CHIP 0.01 DM C902 87-018-205-080 CAP, CERA-SOL 0.022
C72 87-010-263-080 CAP, ELECT 100-10V C903 87-018-205-080 CAP, CERA-SOL 0.022
C904 87-018-205-080 CAP, CERA-SOL 0.022
C73 87-010-197-080 CAP, CHIP 0.01 DM CNA901 8A-CDB-621-010 CONN ASSY,3P POWER
C75 87-010-197-080 CAP, CHIP 0.01 DM
C91 87-010-197-080 CAP, CHIP 0.01 DM !PR901 87-A90-092-080 PROTECTOR,2.5A 491
C92 87-010-197-080 CAP, CHIP 0.01 DM
C93 87-010-197-080 CAP, CHIP 0.01 DM
MOTOR C.B
CF1 87-A91-094-010 FLTR,CDA10.7 MG80A
CF2 82-785-747-080 CF,MS2 GHY,R M2 9X-262-576-910 MOTOR GEAR ASSY
CF3 82-785-747-080 CF,MS2 GHY,R PIN3 91-564-722-110 CONNECTOR 6P
CN2 87-099-194-010 CONN,6P 6216V SW1 91-572-085-120 LEAF SW
CN3 87-A60-110-010 CONN BASE 4P
BATT C.B
· Regarding connectors, they are not stocked as they are not the initial order items.
The connectors are available after they are supplied from connector manufacturers upon the order is received.
6
LCD DISPLAY
LCD, HLC7107ACH-11
CHIP RESISTOR PART CODE
Chip Resistor Part Coding
8 8
A
Figure
Resistor Code
Value of resistor
Chip resistor
Dimensions (mm) :A
Wattage Type Tolerance Symbol Form L W t Resistor Code : A
1/16W 1005 5% CJ 1.0 0.5 0.35 104
L
1/16W 1608 5% CJ t 1.6 0.8 0.45 108
1/10W 2125 5% CJ W 2 1.25 0.45 118
1/8W 3216 5% CJ 3.2 1.6 0.55 128
TRANSISTOR ILLUSTRATION
C
B
ECB ECB E ECB ECB
2SB1655E DTC114TS 2SA1162Y 2SA933RS 2SA933S
2SC2712 2SC1740S R 2SA1296
2SC2714 DTC124XS 2SA1318TU
DTC114TK 2SC1740 S
DTC114YK 2SC1815
DTC144EK 2SC2001
7 8
WIRING-1 (MAIN/TAPE)
1 2 3 4 5 6 7 8 9 10 11 12 13 14
A
MOTOR C.B
M2
B + M2
(SLED MOTOR)
_ SW1
(INSIDE LIMIT SW)
M3
C (SPINDLE MOTOR)
SW1
PIN3
_ +
D
M3
E
F
G
H
I
J
K
9 10
SCHEMATIC DIAGRAM-1 (MAIN)
C812
1000P C811
1000P
R810 R809
330K 330K
11 12
SCHEMATIC DIAGRAM-2 (CD)
13 14
WIRING-2 (POWER)
1 2 3 4 5 6 7
A
B
C
D
E
F
G
H
I
J
K
15
WIRING-3 (TU)
1 2 3 4 5 6 7
A
B
C
D
E
F
G
H
I
J
K
16
SCHEMATIC DIAGRAM-3 (TUNER)
VT
TU C.B
17 18
WIRING-4 (FRONT)
1 2 3 4 5 6 7 8 9 10 11 12 13 14
A
B
C
D
E
F
G
H
I
J
K
19 20
SCHEMATIC DIAGRAM-4 (FRONT)
21 22
ELECTRICAL ADJUSTMENT
L003 < TUNER SECTION >
(BAR-ANT)
1. AM IF Adjustment
L007 ....................................................................... 450kHz
TU C.B 3 2. AM VT Adjustment
Settings: · Test point: C39+
· Adjustment location: L004
Method: Set to AM 1000kHz adjust L004 so that the test
point becomes 3.7V±0.02V
3. AM Tracking Adjustment
L003 ....................................................................... 600kHz
L005 TC001 HP C.B TC001, L007 ........................................................ 1400kHz
5 3 4. FM VT Adjustment
Settings: · Test point: C39+
· Adjustment location: L006
Method: Set to FM 108MHz adjust L006 so that the test
L007
IC001 point becomes 6.0V±0.2V
L004 J251 78
5. FM Tracking Adjustment
13 L006 L005 ........................................................................ 98MHz
2 < TAPE SECTION >
4 6. Bias frequency Adjustment
L801 ............................................................. 85Hz ±500Hz
7. Tape speed Adjustment
Settings: · Test tape: TTA-100
· Test point: PHONES JACK (J251)
· Adjustment location: SFR of deck motor
Method: Play back the test tape and adjust so that the
C39 output frequency is 3000Hz ±30Hz.
+
8. Azimuth Adjustment
Settings: · Test tape: TTA-320
· Test point: PHONES JACK (J251)
· Adjustment location: Azimuth adjustment
screw
24 Method: Play back the test tape and adjust so that the
output is maximum.
TAPE C.B
L801
6
M1
(DECK MOTOR)
8 7
23 24
IC BLOCK DIAGRAM
IC, TA2149N
IC, LC72121M
25
IC, M61509FP
INA1 1 24 INA2
Mono.SW
INB1 2 23 INB2
INC1 3 MUTE 22 INC2
IND1 4 21 IND2
INE1 5 VOL VOL 20 INE2
Treble Treble
boost boost
QF1 6 19 QF4
QF2 7 18 QF3
TONEH1 8 17 TONEH2
ATT ATT
TONEL1 9 16 TONEL2
Bass Bass
OUT1 10 boost boost 15 OUT2
GND 11 14 VSS
VDD 12 Control logic 13 CONT
IC, LA4227
26
IC, LA6541D
IC, BA4560N
27
IC DESCRIPTION
IC, LA9241ML
Pin No. Pin Name I/O Description
Pin to which external pickup photo diode is connected. RF signal is created by adding
1 FIN2 I
with the FIN1 pin signal. FE signal is created by subtracting from the FIN1 pin signal.
2 FIN1 I Pin to which external pickup photo diode is connected.
Pin to which external pickup photo diode is connected. TE signal is created by
3 E I
subtracting from the F pin signal.
4 F I Pin to which external pickup photo diode is connected.
5 TB I DC component of the TE signal is input.
6 TE I Pin to which external resistor setting the TE signal gain is connected between the TE pin.
7 TE O TE signal output pin.
TES "Track Error Sense" comparator input pin. TE signal is passed through a band-
8 TESI I
pass filter then input.
9 SCI I Shock detection signal input pin.
10 TH I Tracking gain time constant setting pin.
11 TA O TA amplifier output pin.
Pin to which external tracking phase compensation constants are connected between
12 TD I
the TD and VR pins.
13 TD I Tracking phase compensation setting pin.
14 JP I Tracking jump signal (kick pulse) amplitude setting pin.
15 TO O Tracking control signal output pin.
16 FD O Focusing control signal output pin.
Pin to which external focusing phase compensation constants are connected between
17 FD I
the FD and FA pins.
Pin to which external focusing phase compensation constants are connected between
18 FA I
the FD and FA pins.
Pin to which external focusing phase compensation constants are connected between
19 FA I
the FA and FE pins.
20 FE O FE signal output pin.
21 FE I Pin to which external FE signal gain setting resistor is connected between the FE pin.
22 AGND -- Analog signal GND.
23 SP -- No connection.
24 SPI O Single ended output of the CV+ and CV pin input signal.
25 SPG I Pin to which external spindle gain setting resistor in 12 cm mode is connected.
Pin to which external spindle phase compensation constants are connected together
26 SP I
with SPD pin.
27 SPD O Spindle control signal output pin.
28 SLEQ I Pin to which external sled phase compensation constants are connected.
29 SLD O Sled control signal output pin.
30, 31 SL, SL+ I Sled advance signal input pin from microprocessor.
32, 33 JP, JP+ I Tracking jump signal input pin from DSP.
34 TGL I Tracking gain control signal input from DSP. Low gain when TGL = H.
35 TOFF I Tracking off control signal input pin from DSP. Off when TOFF = H.
28
Pin No. Pin Name I/O Description
36 TES O Pin from which TES signal is output to DSP.
"High Frequency Level" is used to judge whether the main beam position is on top of
37 HFL O
bit or on top of mirror.
38 SLOF I Sled servo off control input pin.
39, 40 CV, CV+ I CLV error signal input pin from DSP.
41 RFSM O RF output pin.
RF gain setting and EFM signal 3T compensation constant setting pin together with
42 RFS I
RFSM pin.
"Slice Level Control" is the output pin which controls the RF signal data slice level by
43 SLC O
DSP.
44 SLI I Input pin which control the data slice level by the DSP.
45 DGND -- Digital system GND.
46 FSC O Output pin to which external focus search smoothing capacitor is connected.
47 TBC I "Tracking Balance Control" EF balance variable range setting pin.
48 NC -- No connection.
49 DEF O Disc defect detector output pin.
50 CLK I Reference clock input pin. 4.23 MHz of the DSP is input.
51 CL I Microprocessor command clock input pin.
52 DAT I Microprocessor command data input pin.
53 CE I Microprocessor command chip enable input pin.
54 DRF O "Detect RF" RF level detector output.
55 FSS I "Focus Search Select" focus search mode (± search/+ search) select pin.
56 VCC2 -- Servo system and digital system Vcc pin.
57 REFI -- Pin to which external bypass capacitor for reference voltage is connected.
58 VR O Reference voltage output pin.
59 LF2 I Disc defect detector time constant setting pin.
60 PH1 I Pin to which external capacitor for RF signal peak holding is connected.
61 BH1 I Pin to which external capacitor for RF signal bottom holding is connected.
62 LDD O APC circuit output pin.
63 LDS I APC circuit input pin.
64 VCC1 -- RF system Vcc pin.
29
IC, LC78622ED
Pin No. Pin Name I/O Description
1 DEFI I Defect sense signal (DEF) input pin. (Connect to 0V when not used).
2 TAI I Test signal input pin with built-in pull-down resistor. Be sure to connect to 0V.
3 PDO O Phase comparator output pin to control external VCO.
4 VVSS -- GND pin for built-in VCO. Be sure to connect to 0V.
For PLL.
5 ISET I Pin to which external resistor adjusting the PD0 output current.
6 VVDD -- Power supply pin for built-in VCO.
7 FR I Pin for VCO frequency range adjustment.
8 VSS -- Digital system GND. Be sure to connect to 0V.
9 EFMO O EFM signal output pin.
For slice level control.
10 EFMIN I EFM signal input pin.
11 T2 I Test signal input pin with built-in pull-down resistor. Be sure to connect to 0V.
12, 13 CLV+, CLK- O Disc motor control output. Three level output is possible using command.
___ Rough servo or phase control automatic selection monitoring output pin. Rough servo
14 V/P O
at H. Phase servo at L.
15 HFL I Track detect signal input pin. Schmidt input.
16 TES I Tracking error signal input pin. Schmidt input.
17 TOFF O Tracking OFF output pin.
18 TGL O Tracking gain selection output pin. Gain boost at L.
19, 20 JP+, JP- O Track jump control signal output pin. Three level output is possible using command.
21 PCK O EFM data playback clock monitoring pin 4.3218 MHz when phase is locked in.
Sync signal detection output pin. H when the sync signal which is detected from EFM
22 FSEQ O
signal and thesync signal which is internally generated agree.
23 VDD -- Digital system power supply pin.
24 SL+ O Moves the sled to outer circumference.
25 SL- O Moves the sled to inner circumference.
26 -- -- Not connected.
27 PUIN I CD pickup inner switch detection.
28 RW O Read, wright signal.
29 EMPH O De-emphasis monitor output pin. De-emphasis disc is being played back at H.
30 C2F O C2 flag output pin.
31 DOUT O DIGITAL OUT output pin. (EIAJ format).
32, 33 T3, T4 I Test signal input pin with built-in pull-down resistor. Be sure to connect to 0V.
34 N.C. -- Not used. Set the pin to open.
35 MUTEL O L-channel mute output pin.
36 LVDD -- L-channel power supply pin.
L-channel 1-bit DAC.
37 LCHO O L-channel output pin.
38 LVSS -- L-channel GND. Be sure to connect to 0V.
39 RVSS -- R-channel GND. Be sure to connect to 0V.
40 RCHO O R-channel output pin.
R-channel 1-bit DAC.
41 RVDD -- R-channel power supply pin.
42 MUTER O R-channel mute output pin.
30
Pin No. Pin Name I/O Description
43 XVDD -- Crystal oscillator power supply pin.
44 XOUT O
Pin to which external 16.9344 MHz crystal oscillator is connected.
45 XIN I
46 XVSS -- Crystal oscillator GND pin. Be sure to connect to 0V.
47 SBSY O Subcode block sync signal output pin.
48 EFLG O C1, C2, single and dual correction monitoring pin.
49 PW O Subcode P, Q, R, S, T, U and W output pin.
50 SFSY O Subcode frame sync signal output pin. Falls down when subcode enters standby.
Subcode read clock input pin. Schmidt input. (Be sure to connected to 0V when not
51 SBCK I
in use.)
Pin outputting the 7.35 kHz sync signal which is generated by dividing frequency of
52 FSX O
crystal oscillator.
53 WRQ O Subcode Q output standby output pin.
54 RWC I Read/write control input pin. Schmidt input.
55 SQOUT O Subcode Q output pin.
56 COIN I Command input pin from microprocessor.
___________
57 CQCK I Command input read clock or subcode read input clock from SQOUT pin
58 RES I LC78622 reset input pin. Set this pin to L once when the main power is turned on.
59 T11 O Test signal output pin. Use this pin as open (normally L output).
60 16M O 16.9344 MHz output pin.
61 4.2M O 4.2336 MHz output pin.
62 T5 I Test signal input pin with built-in pull-down resistor. Be sure to connect to 0V.
______ Chip select signal input pin with built-in pull-down resistor. Be sure to connect to 0V
63 CS I
while it is not controlling.
64 T1 I Test signal input pin without built-in pull-down resistor. Be sure to connect to 0V.
31
IC, LC867132V-5P07
Pin No. Pin Name I/O Description
1 O-RMC/CE O CD read/write control output.
2 O-DATA O Data output to sound processor IC (M62495FP).
3 O-CLK O Clock output to sound processor IC (M62495FP).
4 NC -- Not Connected.
5 O-CLK SFT O Clock shift output of the microcomputer.
6 I-HOLD I Hold status detection.
7 I-RST I Microcomputer reset.
8 XT1 (IN) I
Connected to 32.768kHz crystal oscillator.
9 XT2 (OUT) O
10 VSS1 -- GND.
11 CF1 (IN) I
Connected to 5.76MHz Ceramic Filter.
12 CF2 (OUT) O
13 VDD1 -- Power supply for microcomputer (+5V).
14 I-FM ST I FM STEREO status input.
15 I-KEYO I KEY AD input.
16 I-CD SW I CD DOOR SW status detection input.
17 I-KEY1 I KEY AD input.
18 I-MOTOR I DECK MECHA MOTOR status input.
19 I-REC I REC status input.
20 I-FM/AM (NC) I FM, AM status input. (Not connected)
21 I-TU DO I Data input from tuner PLL.
22 O-BASS LED (NC) O BASS LED ON/OFF control output. (Not connected)
23 O-QS LED O Q-Sound LED ON/OFF control output.
24 NC -- Not connected.
25 O-INT O INT DIODE MATRIX detection output.
26 I-DRF I CD RF level detection input.
27 I-WRQ I CD sub-code Q standby input.
28 I-REMO I Remote control input.
29 SO/PAO (NC) O LCD segment output and initial settings output. (SW) (Not connected)
30 S1/PA1 (NC) O LCD segment output and initial settings output. (LW) (Not connected)
31 S2/PA2 O LCD segment output and initial settings output. (MW 10K)
32 S3/PA3 (NC) O LCD segment output and initial settings output. (FM WIDE) (Not connected)
33 S4/PA4 (NC) O LCD segment output and initial settings output. (OIRT) (Not connected)
34 S5/PA5 (NC) O LCD segment output and initial settings output. (SW2) (Not connected)
35 S6/PA6 O LCD segment output and initial settings output. (SYN)
36 S7/PA7 O
LCD segment output and initial settings output.
37-40 S8-S11 O
41 VDD3 -- Power supply for microcomputer (+5V).
42 VSS3 -- GND.
43-50 S12-S19 O LCD segment output.
51-54 S20-S23 (NC) O LCD segment output. (Not Connected)
32
Pin No. Pin Name I/O Description
55 O-CD LED O LED ON/OFF control output for CD functions.
56 O-TU LED O LED ON/OFF control output for TU functions.
57 O-TA LED (NC) O LED ON/OFF control output for TAPE functions. (Not Connected)
58 O-ROCK LED O LED ON/OFF control output for ROCK.
59 O-POP LED O LED ON/OFF control output for POP.
60 O-JAZZ LED O LED ON/OFF control output for JAZZ.
61 NC --
62 I-CD TEST (NC) I Not connected.
63 I-TU TEST (NC) I
64-66 COM0-COM2 O LCD common output.
67 NC -- Not connected.
68 VSS2 -- GND.
69 VDD2 -- Power supply for microcomputer (+5V).
70 O-CD ON O CD PWR control output.
71 O-TU ON O TU PWR control output.
72 O-P.CONT O Power supply control output.
73 NC -- Not connected
74 O-MUTE O Main mute output.
75 O-FM MONO (NC) O FM force control MONO output. (Not connected)
76 O-BEAT CONT O BEAT switch over output.
77 O-QSOUND O Q-Sound ON/OFF output.
78 O-COIN O CD command output.
79 I-SQOUT I CD sub-code Q input.
80 O-CQCK O CLK for CD commands/sub-codes.
33
MECHANICAL PARTS LIST 1/1
REF. NO PART NO. KANRI DESCRIPTION REF. NO PART NO. KANRI DESCRIPTION
NO. NO.
1 8A-CDB-006-010 WINDOW,CASS 35 8A-CHB-202-010 HLDR,LCD
2 8A-CDB-008-010 BOX,CASS 36 8A-CDB-212-010 PLATE,REC
3 8A-CDB-204-010 SPR-T,CASS 37 8A-CHB-619-010 FF-CABLE, 8P 1.25 CD-FR
4 8A-CDB-001-010 CABI,FR 38 8A-CHB-618-010 FF-CABLE, 16P 1.25 FR-MAIN
5 88-CD8-622-010 SPKR,F 77 7OHM 3W 39 8A-CDB-219-010 HLDR,TRAN
6 8Z-CDB-208-010 HLDR,SPKR ! 40 8A-CDB-651-010 PT,H 2.5W EI48X23<1LH>
7 8A-CDB-205-010 PLATE,OIL DUMP ! 40 8A-CDB-650-010 PT,U 2.5W EI48X23<2UW,1US>
8 87-063-164-010 OIL-DMPR 80 41 8A-CDB-019-010 HANDL,GRIP
9 8A-CDB-206-010 BASE,CD 42 8A-CDB-018-010 COVER, HANDL
10 8A-CDB-016-010 BTN,CD 43 8Z-CH4-640-010 ANT,ROD
11 8A-CHB-013-010 WINDOW,DISPLAY<1LH> 44 8A-CHB-001-010 CABI,REAR
11 8A-CHB-002-010 WINDOW,DISPLAY<2UW,1US> 45 87-A91-369-010 SW,AC SL 2 2 2 SDKGA41700<1LH>
12 8A-CDB-023-010 GRILLE,SPKR 46 8A-CDB-623-010 FF-CABLE, 16P 1.0 CD-RF
13 8Z-CT6-213-010 BASE,CHUCK 47 8A-CDB-020-010 LID,BATT
14 8Z-CT6-214-010 RING,CHUCK 48 86-CT9-223-010 CUSH,FOOT
15 87-036-368-010 MAGNET 49 8A-CDB-207-010 HLDR,ANT
16 86-CT9-222-010 PLATE,MAGNET ! 50 87-A60-178-010 JACK,AC E W/SW<1LH>
17 86-CT9-217-010 HLDR,CHUCK A(S) ! 50 87-A60-177-010 JACK,AC U W/SW<2UW,1US>
18 8A-CDB-009-010 BOX,CD 51 8A-CDB-215-010 SPR-T,BATT
19 8A-CHB-011-010 WINDOW,CD 52 8A-CDB-220-010 HLDR,M66 BAR ANT
20 8A-CHB-014-010 BTN,FUNC 53 8A-CDB-015-010 KEY,CASS
21 8A-CDB-213-010 BASE,FUNC 54 8A-CDB-216-010 PLATE,TRAN
22 8A-CDB-014-010 BTN,QSOUND 55 87-A90-086-010 COVER,AC-SOCKET
23 8A-CDB-003-010 CHAS,CD 56 8A-CDB-626-010 CONN ASSY,4P CASS HEAD
24 8A-CDB-021-010 LENS,FUNC 57 8A-CDB-633-010 CONN ASSY,4P SPKR
25 8A-CDB-203-010 HLDR,LED FUNC 58 8A-CDB-625-010 CONN ASSY,4P CASS MECHA
26 88-CH6-220-010 CUSHION,CD A A 81-CD5-204-010 SCREW CD
27 8Z-CT9-064-010 PANEL CD B 87-651-104-410 VT1+3-30
28 87-036-389-010 SW,PUSH LOCK C 87-741-096-410 UT2+3-10
29 8A-CDB-218-010 SPR-T,CD D 87-751-097-410 SCREW 3X12
30 8A-CDB-620-010 CONN ASSY,2P CD-DOOR E 87-261-096-410 SCREW,V+3-10 GLD
31 M8-ZZK-E90-070 DA11T3C F 87-741-074-410 UT2+2.6-8
32 87-063-165-010 OIL-DMPR 150 G 87-261-032-410 SCREW,V+2-3 GLD
33 8A-CDB-214-010 BASE,VOL H 87-751-095-410 VT2+3-8 W/O
34 8A-CDB-012-010 BTN,VOL
COLOR NAME TABLE
Basic color symbol Color Basic color symbol Color Basic color symbol Color
B Black C Cream D Orange
G Green H Gray L Blue
LT Transparent Blue N Gold P Pink
R Red S Silver ST Titan Silver
T Brown V Violet W White
WT Transparent White Y Yellow YT Transparent Yellow
LM Metallic Blue LL Light Blue GT Transparent Green
LD Dark Blue DT Transparent Orange
34
MECHANICAL EXPLODED VIEW 1/1
P.C.B
H H H 41
28
29
19
C
23 H
42
18 H H B 43
52 D
24 CHASS,TU
22
BAR-ANT
21 32 B D
40
D 7
34 E E
24
20 27 33
17
31 P.C.B
16 25 44
D 50
15 P.C.B
55
26
14 25 H
A D
C 39 F F