Text preview for : ht-af5-ht-as5-sa-wa5.pdf part of Sony SA-WA5 SA-WA5 is the amplifier, HDMI, tuner and
active subwoofer section in HT-AF5/AS5
AEP Model
UK Model
Back to : ht-af5-ht-as5-sa-wa5.pdf | Home
SA-WA5
SERVICE MANUAL AEP Model
UK Model
Ver. 1.0 2010.04
· SA-WA5 is the amplifier, HDMI, tuner and
active subwoofer section in HT-AF5/AS5.
This system incorporates Dolby* Digital and Pro SPECIFICATIONS
Logic Surround and the DTS** Digital Surround
System. Amplifier section AM tuner section
* Manufactured under license from Dolby POWER OUTPUT (rated) Tuning range 531 kHz 1,602 kHz
Laboratories. Dolby, Pro Logic, and the double-
FRONT L + FRONT R (9 kHz step)
D symbol are trademarks of Dolby Laboratories.
108 W + 108 W (at 3 ohms, 1 kHz, 1% THD) Antenna (Aerial) AM loop antenna (aerial)
** Manufactured under license under U.S. Patent
POWER OUTPUT (reference) Intermediate frequency
#'s: 5,451,942; 5,956,674; 5,974,380;
5,978,762; 6,487,535 & other U.S. and world- FRONT L/FRONT R/CENTER/ 450 kHz
wide patents issued & pending. DTS and DTS SUR L/SUR R 167 W General
Digital Surround are registered trademarks and (per channel at 3 ohms, 1 kHz) Power requirements
the DTS logos and Symbol are trademarks of SUBWOOFER 165 W
Area code Power requirements
DTS, Inc. © 1996-2008 DTS, Inc. All Rights (at 3 ohms, 60 Hz)
CEL, CEK 220240 V AC, 50/60 Hz
Reserved. Inputs
Analog Sensitivity: 1 V/50 kohms Power output (DIGITAL MEDIA PORT)
This system incorporates High-Definition Digital (Coaxial) Impedance: 75 ohms DC OUT: 5 V, 0.7 A MAX
Multimedia Interface (HDMITM) technology. HDMI,
the HDMI Logo, and High-Definition Multimedia HDMI Video
Power consumption
Interface are trademarks or registered trademarks Input/Output (HDMI Repeater block)
640 × 480p@60 Hz Area code Power consumption
of HDMI Licensing LLC in the United States and
other countries. 720 × [email protected]/60 Hz CEL, CEK 110 W
1280 × [email protected]/60 Hz
Power consumption (during standby mode)
"x.v.Colour" and "x.v.Colour" logo are trademarks 1920 × [email protected]/60 Hz
of Sony Corporation. 0.3 W (When Control for
1920 × [email protected]/60 Hz
HDMI and S-AIR standby are set to off)
720 × 576p@50 Hz
"BRAVIA" is a trademark of Sony Corporation. 1280 × 720p@50 Hz
Speaker section
1920 × 1080i@50 Hz
"PlayStation" is a trademark of Sony Computer Subwoofer
1920 × 1080p@50 Hz
Entertainment Inc. Speaker unit 130 mm, cone type
1920 × 1080p@24 Hz Enclosure type Bass reflex
HDMI Video (3D) Rated impedance 3 ohms
"S-AIR" and its logo are trademarks of Sony
Input/Output (HDMI Repeater block) Dimensions (w/h/d) (Approx.)
Corporation.
1280 × [email protected]/60Hz Frame packing 196.0 mm × 450.0 mm ×
1920 × [email protected]/60Hz Frame packing 410.5 mm
1920 × [email protected]/60Hz Side-by-Side (Half) (with foot)
1920 × [email protected]/60Hz Side-by-Side (Half) Mass (Approx.) 10.4 kg (with foot)
1280 × 720p@50Hz Frame packing Design and specifications are subject to
1920 × 1080i@50Hz Frame packing change without notice.
1920 × 1080i@50Hz Side-by-Side (Half)
1920 × 1080p@50Hz Side-by-Side (Half) Halogenated flame retardants are not used in
1920 × 1080p@24Hz Frame packing the certain printed wiring boards.
FM tuner section
Tuning range 87.5 MHz 108.0 MHz
(50 kHz step)
Antenna (Aerial) FM wire antenna (aerial)
Antenna (Aerial) terminals
75 ohms, unbalanced
Intermediate frequency
10.7 MHz
ACTIVE SUBWOOFER
9-890-534-01 Sony Corporation
2010D08-1 Audio & Video Business Group
© 2010.04 Published by Sony EMCS (Malaysia) PG Tec
SA-WA5
NOTES ON CHIP COMPONENT REPLACEMENT TABLE OF CONTENTS
· Never reuse a disconnected chip component.
· Notice that the minus side of a tantalum capacitor may be dam- 1. SERVICING NOTES.......................................... 3
aged by heat.
2. DISASSEMBLY
About area codes 2-1. Disassembly Flow ........................................................... 4
The area code of the system you purchased is 2-2. Top Panel Block .............................................................. 4
shown on the rear of the subwoofer (see the 2-3. AMP Block ..................................................................... 5
illustration below). 2-4. Case Top Block ............................................................... 5
2-5. S-AIR Board ................................................................... 6
2-6. Back Panel Block ............................................................ 6
EZW-T100
2-7. MAIN Board, SW CONNECT Board............................. 7
2-8. Tuner (FM/AM), IO ANALOG Board, IO DIGITAL
Board, SPEAKER Board, HDMI PC Board .................. 7
2-9. POWER Board ............................................................... 8
3-0. Reflector, Loudspeaker ................................................... 8
3. TEST MODE ........................................................ 9
L
Area code 4. ELECTRICAL ADJUSTMENT .......................... 11
ANTENNA
DMPORT
DC5V
0.7A MAX AUTO
CAL MIC
R
FM 75
AUDIO IN AUDIO IN COAXIAL AM
SA-CD/CD TV
DVD IN
HDMI
BD IN SAT/CATV IN
ARC
TV OUT
DIGITAL
5. DIAGRAMS
5-1. Block Diagram - MAIN Section -................................... 13
SPEAKERS OPT IN COAX IN
FRONT R CENTER FRONT L SUR R SUR L
SAT/CATV TV VIDEO
5-2. Block Diagram - HDMI PC Section - ............................. 14
5-3. Block Diagram - S-AIR Section - ................................... 15
5-4. Block Diagram - AMP Section - ..................................... 16
Any differences in operation, according to the area 5-5. Block Diagram - POWER SUPPLY Section - ................ 17
code, are clearly indicated in the text, for example, 5-6. Printed Wiring Board
"Models of area code AA only". - MAIN Board (Component Side) - ................................ 19
5-7. Printed Wiring Board
- MAIN Board (Conductor Side) - .................................. 20
5-8. Schematic Diagram - MAIN Board (1/5) - ..................... 21
5-9. Schematic Diagram - MAIN Board (2/5) - ..................... 22
5-10. Schematic Diagram - MAIN Board (3/5) - ..................... 23
5-11. Schematic Diagram - MAIN Board (4/5) - ..................... 24
5-12. Schematic Diagram - MAIN Board (5/5) - ..................... 25
5-13. Printed Wiring Board
- KEY, SPEAKER, and SW CONNECT Board - ........... 26
5-14. Schematic Diagram
- KEY, SPEAKER and SW CONNECT Board - ............ 26
5-15. Printed Wiring Board - HDMI PC Board - ..................... 27
5-16. Schematic Diagram - HDMI PC Board (1/2) - ............... 28
5-17. Schematic Diagram - HDMI PC Board (2/2) - ............... 29
5-18. Printed Wiring Board - DISPLAY Board - ..................... 30
5-19. Schematic Diagram - DISPLAY Board - ........................ 31
5-20. Printed Wiring Board
- IO DIGITAL, S-AIR Board - ....................................... 32
5-21. Schematic Diagram - S-AIR Board - .............................. 33
5-22. Schematic Diagram - IO DIGITAL Board - ................... 34
5-23. Printed Wiring Board - IO ANALOG Board - ................ 35
5-24. Schematic Diagram - IO ANALOG Board - ................. 36
5-25. Printed Wiring Board - POWER Board -........................ 37
5-26. Schematic Diagram - POWER Board - .......................... 38
5-27. Printed Wiring Board - CONNECT Board - ................... 39
5-28. Schematic Diagram - CONNECT Board -...................... 39
6. EXPLODED VIEWS
6-1. Cabinet Section ............................................................... 49
6-2. Top Panel Section .......................................................... 50
SAFETY-RELATED COMPONENT WARNING! 6-3. AMP Section ................................................................... 51
6-4. Main Section ................................................................... 52
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE 6-5. Chassis Section ............................................................... 53
WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. 7. ELECTRICAL PARTS LIST ............................ 54
REPLACE THESE COMPONENTS WITH SONY PARTS
WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS
MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
2
SA-WA5
SECTION 1
SERVICING NOTES
UNLEADED SOLDER NOTE OF REPLACING THE IC300, IC400 AND IC500
Boards requiring use of unleaded solder are printed with the lead- ON THE MAIN BOARD AND THE COMPLETE MAIN
free mark (LF) indicating the solder contains no lead. BOARD
(Caution: Some printed circuit boards may not come printed with When IC300, IC400 and IC500 on the MAIN board and the com-
the lead free mark due to their particular size) plete MAIN board are replaced, it is necessary to spread the com-
pound (OIL COMPOUND G777) (Part No. J-2501-335-A ) be-
: LEAD FREE MARK tween the main board and the heat sink.
Unleaded solder has the following characteristics. Spread the compound referring to the figure below.
· Unleaded solder melts at a temperature about 40 °C higher MAIN Board (Component Side)
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!
· Strong viscosity
Unleaded solder is more viscous (sticky, less prone to flow)
IC300 IC400 IC500
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
· Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder. oil compound G777
(J-2501-335-A)
· JIG
When disassembling the set, use the following jig (for speaker
removal).
CAPACITOR ELECTORICAL DISCHARGE
Part No. J-2501-238-A JIG FOR SPEAKER REMOVAL
PROCESSING
When checking the board, for the electric shock prevention, con-
nect the resistors to both ends of respective capacitor (C903) to
discharge the capacitor (C903).
NOTE OF CONFIRMING THE BOARDS POWER Board (Conductor Side)
Protecting is generated when energizing with the heat sink de-
tached. Fix the heat sink to the MAIN board by using the screw
and the nut without fail when you confirm the board.
CONFIRMING THE POWER BOARD
The POWER board can be confirmed by removing the bottom
bracket of the AMP Box.
C903
NOTE THE IC3500 AND IC3501 ON THE HDMI PC
BOARD REPLACING 800 /2 W
IC3500 and IC3501 on the HDMI PC board cannot exchange
with single. When these parts are damaged, exchange the entire
mounted board.
3
SA-WA5
SECTION 2
DISASSEMBLY
· This set can be disassembled in the order shown below.
2-1. DISASSEMBLY FLOW
SET
2-2. TOP PANEL BLOCK 2-3. AMP BLOCK 3-0. REFLECTOR, LOUDSPEAKER
(Page 4) (Page 5) (Page 9)
2-4. CASE TOP BLOCK
(Page 5)
2-5. S-AIR BOARD 2-6. BACK PANEL BLOCK 2-9. POWER BOARD
(Page 6) (Page 6) (Page 8)
2-7. MAIN BOARD, SW CONNECT BOARD 2-8. TUNER (FM/AM), IO ANALOG BOARD,
(Page 7) IO DIGITAL BOARD, SPEAKER BOARD,
HDMI PC BOARD
(Page 7)
Note: Follow the disassembly procedure in the numerical order given.
2-2. TOP PANEL BLOCK
7 Top Panel block
3 wire (flat type)
(13 core) (CN1352)
4 cushion H15
5 Insert a jig into a recess
6 in the bottom of the top panel
to raise the top panel assy a little.
1 four screws
(BVTT4 20)
2 cover (Fan)
4
SA-WA5
2-3. AMP BLOCK
Note: Work after laying the set frontways.
1 four screws
(BV TAPPING 4 20)
2 four screws
(BVTP3 8)
3 cover (connector)
7 AMP block
5 holder (AMP)
6 connector
(CN152)
4 eight screws
(BVTP3 8)
2-4. CASE TOP BLOCK
3 two screws
(BVTP 3 8) b 1 wire (flat type)
(15 core) (CN1351)
cushion (35T100)
4 CONNECT board
5 four screws 2 connector
(BVTP 3 8) (CN1353)
a
7 Case Top 6 nine screws
(BVTP 3 8)
a
9 Fan
8 two screws
(BVTT 4 20)
b
5
SA-WA5
2-5. S-AIR BOARD
2 two screws
(BVTP 3 8)
1 wire (flat type)
(23 core) (CN1401)
a
4 holder (S-AIR)
5 S-AIR board
3 two screws
(BVTP 3 8)
a
2-6. BACK PANEL BLOCK
1 six screws
(BVTP 3 8)
6 Back Panel Block
a
b c
2 connector (CN1009)
5 connector
(CN560)
a
4 wire (flat type)
(19 core) (CN1003)
c
b
3 wire (flat type)
(29 core) (CN1016)
6
SA-WA5
2-7. MAIN BOARD, SW CONNECT BOARD
1 four screws
2 heatsink (BVTP 3 16)
5 one screw
3 one screw (BVTP 3 8)
(BVTP 3 8)
6 clamp (L35)
4 clamp 8 connector
(CN566)
7 connector (CN1006) q; five screws
(BVTP 3 8)
b
qa MAIN board
9 connector qs connector
(CN562) (CN151)
a
a qd one screw
pin lead (BVTP 3 8)
qg bracket (SW Connect)
b
qh SW CONNECT board
qf one screw
(BVTP 3 8)
Note: When MAIN board is replaced, spread the com-
pound referring to "NOTE OF REPLACING
THE IC300, IC400 AND IC500 ON THE MAIN
BOARD AND THE COMPLETE MAIN BOARD"
on servicing notes (page 3).
2-8. TUNER (FM/AM), IO ANALOG BOARD, IO DIGITAL BOARD, SPEAKER BOARD, HDMI PC
BOARD
1 three screws 4 two screws
(BVTP 3 8) (BVTP 3 8)
2 five screws
(BVTP 3 8) 5 three screws
(BVTP 3 8)
3 two screws
(BVTP 3 8)
7 woven (15T25),
fabric non
9 wire (flat type) a
(7 core) (CN604)
a
6 wire (flat type)
(11 core) (CN602, CN603)
q; wire (flat type) pin lead ql IO DIGITAL board
(29 core) (CN605, CN606) qk SPEAKER board
qj connector
qa IO ANALOG board (CN101, CN102)
qs connector
8 tuner (FM/AM) (CN3510)
qf three screws
(BVTP 3 8)
qh HDMI PC board
qd wire (flat type)
(19 core) (CN3511, CN3512)
qg bracket (HDMI PC)
7
SA-WA5
2-9. POWER BOARD
1 connector
(CN566)
q; Bracket (AMP)
2 connector
(CN1006) 7 power cord connector
(CN901)
5 eight screws
(BVTP 3 8)
9 POWER board
6 clamp (L35)
8 fuse (F901)
4 Bracket (POWER)
3 ten screws
(BVTP 3 8)
3-0. REFLECTOR, LOUDSPEAKER
2 two screws
(3.5 12)
qs loudspeaker
3 bracket reflector
1 two screws
(BVTP 3 8)
qa four screws
(BV TAPPING 4 16)
q; Reflector
qh Duct A
5 two screws
(3.5 12)
7 four screws
qg Packing CT (BV TAPPING 4 16)
6 bracket reflector qf Duct B
4 two screws
(BVTP 3 8) 9 Reflector board
qd four screws 8 five screws
(BV TAPPING 4 16) (TAPPING 3.5 14)
8
SA-WA5
SECTION 3
TEST MODE
1. COLD RESET 5. TUNER FACTORY PRESET
All preset contents are cleared when this mode is activated. Use Not used for the servicing.
this mode before returning the product to clients upon completion Press the [?/1] button if having entered this mode.
of repair.
Procedure: 6. VACS DISPLAY
1. Press the [?/1] button on the set to turn the power on. Procedure:
2. Keeps pressing the [?/1] button on the set for about five sec- 1. Enter the test mode menu.
onds. 2. Press the []/[] buttons to select "VACS DISP", and press the
3. The message "CLEARED" appears, then the set turns off. [ENTER] button.
3. It will appear the VACS status
2. HOW TO ENTER THE TEST MODE
Note: The operation of the button of the following test modes is only a 7. VACS ON/OFF
remote commander. Procedure:
Procedure: 1. Enter the test mode menu.
1. Press the [?/1] button to turn the power on. 2. Press the []/[] buttons to select "VACS ON OFF", and press
2. Press the buttons in order of [TUNER] [RETURN] Hold the [ENTER] button.
SHIFT button ([ENTER] [0] [1] [0]) [SOUND 3. The VACS status will change.
FIELD +]
3. The message "TEST MENU" appears, then enter the test 8. DSP HALT MODE
menu. Not used for the servicing.
4. Press the [?/1] button to exit from the test mode. Press the [?/1] button if having entered this mode.
3. PANEL TEST 9. DSP STATUS DISPLAY
3-1. Pattern check Not used for the servicing.
Procedure: Press the [?/1] button if having entered this mode.
1. Enter the test mode menu.
2. Press the []/[] buttons to select "PANEL", and press the 10. HDMI UCOM UPDATE
[ENTER] button. Procedure:
3. All segments and all LEDs turn on. Change as follows all on, 1. Enter the test mode menu.
test pattern 1, test pattern 2 and test pattern 3, all on in this 2. Press the []/[] buttons to select "HDMI VER", and press the
order. [ENTER] button.
AACLPCM NIGHT SLEEP HDMI COAX OPT TUNED ST S-AIR ECO MUTING DTS 96/24
3. HDMI MICOM software version is displayed.
;TrueHD -ES NEO:6 4. Press the [?/1] button to exit from the test mode.
;D + EX DTS -HDLBR
;PL II x MSTR HI RES
11. HDMI THROUGH DMPORT UPDATE
Procedure:
AACLPCM NIGHT SLEEP HDMI COAX OPT TUNED ST S-AIR ECO MUTING DTS 96/24
;TrueHD -ES NEO:6 1. Enter the test mode menu.
;D + EX DTS -HDLBR
;PL II x MSTRHI RES
2. Press the []/[] buttons to select "HDMI UPD", and press the
[ENTER] button.
3. Connect the programming jig to dmport connection.
LPCM TUNED ST DTS 4. Flash HDMI software from computer through programming
NEO:6
;D EX DTS -HD jig.
;PL II MSTR
5. Press the [?/1] button to exit from the test mode.
3-2. Key check
Procedure: 12. DMPORT TEST
1. Enter the test mode menu. Procedure:
2. Press the []/[] buttons to select "PANEL", and press the 1. Connect the DMPORT check jig (Part No. J-2501-309-A) with
[ENTER] button. the DMPORT jack (CN601) on the MAIN board.
3. Press the [VOLUME ] button, while executing pattern check. 2. Press the [?/1] button to turn the power on.
4. The message "K0 V0" appears. "K0" value increases when- 3. Confirm that both LEDs of the DMPORT check jig lights.
ever a button on the set is pressed. However, once a button has (Confirmation the power supply line)
been pressed, it is no longer taken into account. All buttons on 4. Press the [DMPORT] button to select the "DMPORT".
the set is pressed, "K3 V0" is displayed. 5. Enter the test mode menu.
5. Press the [?/1] button to exit from the test mode. 6. Press the []/[] buttons to select the "DMPORT CHK", and
press the [ENTER] button.
3-3. Software version and destination display 7. The message "DMPORT OK." appears on the fluorescent indi-
Procedure: cator tube and enter the digital media port test mode. (Confir-
1. Enter the test mode menu. mation of communication line)
2. Press the []/[] buttons to select "PANEL", and press the When "NO DETECT" and "UART TO" are displayed on
[ENTER] button. the fluorescent indicator tube, confirm the connection of the
3. Press the [VOLUME +] button, while executing pattern check. DMPORT check jig, and enter the mode again.
4. The display of model name, destination, and software version Each time the [>] button is pressed, the connect check and
changes whenever [VOLUME +] button is pressed. adaptor version check are changed.
5. Press the [?/1] button to exit from the test mode. Press the [.] button, connected confirmation of the
DMPORT check jig is done again.
4. AMP TEST 8. To a pin-jack of the DMPORT check jig input information rel-
Not used for the servicing. evant to audio signal (sine-wave 1.0 Vrms).
Press the [?/1] button if having entered this mode. 9. Confirm the output of speakers. (Confirmation of analog sig-
nal)
9
SA-WA5
10. Press the [?/1] button to exit from the test mode. 16. UART FLASH (SOURCE)
Not used for the servicing.
SPEAKER board Press the [?/1] button if having entered this mode.
ANALOG IO board TB101 for FR and C
CN601 TB102 for FL
J001 17. UART FLASH (TARGET)
DMPORT Not used for the servicing.
AF check jig FL/FR Press the [?/1] button if having entered this mode.
amplifier
oscillator (Part No. speakers
J-2501-309-A) 18. COLD RESET
Procedure:
13. DMPORT DEVICE TEST 1. Enter the test mode menu.
Note: It connects with the iPod adaptor and it is necessary to repair hard- 2. Press the []/[] buttons to select "COLD RESET", and press
ness to execute this mode.
the [ENTER] button.
Procedure:
3. The message "CLEARED" appears, then the set turns off.
1. Connect the DMPORT check jig (Part No. J-2501-309-A) with
the DMPORT jack (CN601) on the MAIN board.
2. Enter the test mode menu.
3. Press the []/[] buttons to select "DMPORT DEV", and press
the [ENTER] button.
4. LED on the jig lights.
5. Press the [?/1] button to exit from the test mode.
14. S-AIR TEST MODE
Procedure:
1. Enter the test mode menu.
2. Press the []/[] buttons to select "SAIR TEST", and press the
[ENTER] button.
3. S-AIR test menu is displayed.
4. Press the [?/1] button to exit from the test mode.
14-1. Power
Procedure:
1. Enter the S-AIR test mode.
2. Press the []/[] buttons to select "POWER", and press the
[ENTER] button.
3. The messages "000 SET" is appears.
4. Press the []/[] buttons to select the output power. (OFF or
000 to 063)
5. Press the [ENTER] button, return to S-AIR test mode each
item.
14-2. NAMG
Procedure:
1. Enter the S-AIR test mode.
2. Press the []/[] buttons to select "NAMG", and press the
[ENTER] button.
3. The messages "AUTO" is appears.
4. Press the []/[] buttons to select the NAMG setting value.
(107 to 117)
5. Press the [ENTER] button, return to S-AIR test mode each
item.
14-3. Version check
Procedure:
1. Enter the S-AIR test mode.
2. Press the []/[] buttons to select "VER. CHECK", and press
the [ENTER] button.
3. MICOM software version of S-AIR product is displayed.
4. Press the [ENTER] button, return to S-AIR test mode each
item.
15. S-AIR TEST ELEC MODE
Not used for the servicing.
Press the [?/1] button if having entered this mode.
10
SA-WA5
SECTION 4
ELECTRICAL ADJUSTMENT
TUNER SECTION
[FM AUTO STOP CHECK]
generator
set
OUT (75 )
Procedure:
1. Turn on the set.
2. Input the following signal from Signal Generator to FM
antenna input directly.
Carrier frequency : A = 87.5 MHz, B = 98 MHz, C = 108 MHz
Deviation : 75 kHz
Modulation : 1 kHz
ANT input : 35 dBu (EMF)
Note: Please use 75 ohm "coaxial cable" to connect SG and the set. You
cannot use video cable for checking.
Please use SG whose output impedance is 75 ohm.
3. Set to FM tuner function and scan the input FM signal with
automatic scanning.
4. Confi rm that input Frequency of A, B and C are detected and
automatic scanning stops.
The stop of automatic scanning means "The station signal is
received in good condition."
11
SA-WA5
SECTION 5
DIAGRAMS
· Waveforms
HDMI PC Board MAIN Board
IC3500 4 (XTALOUT) IC4 ih (DPDVLRCK) IC1011 wa (XOUT (O))
1 3 9
3.85 Vp-p 6 Vp-p 4.23 Vp-p
99.872 ns 20.8332 s 81.328 ns
1 V/DIV, 50 ns/DIV 1 V/DIV, 10 S/DIV 1 V/DIV, 50 ns/DIV
IC3000 qa (XOUT) IC4 ij (DPDVBCK) IC1002 qd (Xout)
2 4 q;
3.06 Vp-p 4.66 Vp-p
3.52 Vp-p
325.656 ns
36.896 ns 199.392 ns
1 V/DIV, 20 ns/DIV 1 V/DIV, 100 ns/DIV 1 V/DIV, 100 ns/DIV
IC4 5 qa
0.86 Vp-p 3.28 Vp-p
39.78 ns 20.312 ns
500 mV/DIV, 20 ns/DIV 1 V/DIV, 10 ns/DIV
IC1011 qd (CKOUT)
6
4.3 Vp-p
81.384 ns
1 V/DIV, 50 ns/DIV DISPLAY Board
IC1011 qf (BCK (O)) Q702 (Collector)
7 qs
4 Vp-p
4.66 Vp-p
325.408 ns
325.656 ns
1 V/DIV, 100 ns/DIV 1 V/DIV, 100 ns/DIV
IC1011 qg (LRCK (O))
8
4.09 Vp-p
20.8332 s
1 V/DIV, 10 S/DIV
12
SA-WA5
5-1. BLOCK DIAGRAM - MAIN Section -
DIGITAL AUDIO DIGITAL AUDIO
INPUT SELECTOR INTERFACE RECEIVER
IC804 IC1011
DIGITAL OPTICAL
TV DATA_DIR, ADC_DATA,
RECEIVER 6 1C0
BCK, LRCK, CKOUT
A (Page 15)
IC802 DATA_DIR
DATA(O) 16
CKOUT
OPT IN 1Y 7 3 DIN0 CKOUT 13
BCK
BCK(O) 14
DIGITAL OPTICAL LRCK
DIGITAL SAT/CATV RECEIVER 5 1C1 LRCK(O) 15
IC801
WAVE SHAPPER
IC803
J801
COAX IN
1 7 6 2 4 IC2
VIDEO AUDIO
B A AUDIO(O) 24 B (Page 15)
2 14
HDMISPDIF