Text preview for : 390D electrical.pdf part of Caterpilar Excavator 390D Electrical schematic diagram excavator caterpilar 390D



Back to : 390D electrical.pdf | Home

KENR7737-01
Component Identifiers (CID¹)
Calibration Error ID List August 2011
Module Identifier (MID²) ID Calibration Error Description
Engine Control $0001 ECM Fault
(MID No. 036) $0002 Active Diagnostic Present
CID Component
$0003 Another Calibration is Active
0001 Cylinder #1 Injector
$0004 Calibration Active by Another ECM
0002 Cylinder #2 Injector




KENR7737-01 VOL 1 of 2
0003 Cylinder #3 Injector $0005 Loss of Calibration Interlock
0004 Cylinder #4 Injector $0006 Calibration Aborted by Tool/Monitor
0005 Cylinder #5 Injector $0007 Requested Display Not Supported
0006 Cylinder #6 Injector $0008 Unavailable Display
0091 ThrottlePositionSensor
$0009 Calibration Aborted by ECM
0094 Fuel Delivery Pressure Sensor
$000A Calibration Failure




(Dimensions: 48 inches x 35 inches)
0100 Engine Oil Pressure Sensor
$000B Calibration Not Supported
0102 Boost Pressure Sensor
0110 Engine Coolant Temperature Sensor $0100 Out-of-Range Low - Incr/Decr Parameter

0168 Electrical System Voltage $0101 Out-of-Range High - Incr/Decr Parameter
0172 Intake Manifold Air Temperature Sensor $0102 Invalid Action / Key Stroke Command
0174 Fuel Temperature Sensor $0103 Calibration Value Out-of-Range
0190 Engine Speed Sensor $0104 Calibrated Range Too Small
0248 CAT Data Link
$0105 Calibrated Range Too Large
0261 Engine Timing Calibration
$0106 Calibration Value Not Saved
0262 5 Volt Sensor DC Power Supply
$1000 See Service Manual
0268 Programmed Parameter Fault
0274 Atmospheric Pressure Sensor $1010 Engine Stopped (NoEngineRPM)
44
0286 Low Oil Pressure Lamp $1011 Engine Running (EngineRPMPresent)
3 5

390D Excavator
0291 Engine Cooling Fan Solenoid $1012 Engine RPM Incorrect
0342 Secondary Engine Speed Sensor $1013 Engine High Idle RPM Too Fast 15
2417 Ether Injection Control Solenoid 55
$1014 Engine Low Idle RPM Too Slow


Electrical System
4 23
Machine Control $1015 Abnormal Engine RPM Signal 68
69
(MID No. 039) $1016 Speed Sensor Circuit is Open 35
27 63 40
CID Component $1017 Service Brake Pedal Pressed
0041 8 Volt DC Supply
52 2
0096 Fuel Level Sensor
$1018 Parking Brake Not Engaged
38 48
39 46
43
WAG1-UP
$1019 Parking Brake Engaged 60 34
0167 Alternator Charging Voltage Sensor 45 47 33
50 BYP1-UP
0168 Electrical System Voltage
$101A Implement is Swinging/Traveling
41 66
0190 Engine Speed Sensor $101B Machine Speed Not Zero
51 29 WAP1-UP
25
0246 Proprietary CAN Data Link $1034 Engine Speed Range is Too Great WBT1-UP
0247 SAE J1939 Data Link $1035 Response to Engine Speed Request is Slow/Does Not Respond
0248 CAT Data Link $1040 Load is Applied During Calibration
42
59 61 KCZ1-UP
0254 Electronic Control Module
$1054 Temperature of Hydraulic Oil is Too High
0271 Action Alarm




36 Page,
$1072 Temeprature of Coolant is Too High 30 26
0291 Engine Cooling Fan Solenoid 31
$1074 High Idle Speed of Engine is Too Low 57
0374 Swing Brake Solenoid 67 70
37 49
0466 Left Track Steering Pedal Position Sensor
0467 Right Track Steering Pedal Position Sensor
32
28
0485 Engine Fan Reversing Solenoid
0581 Power Shift Solenoid 19
20 21
0586 Engine Speed Dial Switch
0588 Monitoring System Display Related Electrical Service Manuals 64
0590 Engine Control Module Title Form Number
0598 Travel Speed Solenoid Alternator: 177-9953 (Denso HDB) SENR4130 6
0600 Hydraulic Oil Temperature Sensor Starting Motor: 272-7123 (Delco 50MT) SENR3860
0790 Swing Pump (Outlet) Pressure Sensor 14
Engine Control: RENR5092
0864 Variable Implement Pump Oil Pressure Sensor
Machine Control: KENR8955 54
1118 Neutral Flow Bypass Solenoid
1125 Left Hand Lever Forward/Backward Position Sensor 62
1126 Left Hand Lever Left/Right Position Sensor
1127 Right Hand Lever Forward/Backward Position Sensor
1128 Right Hand Lever Left/Right Position Sensor
1129 Right Side Attachment Pedal Sensor Volume 1 of 2: Cab and Chassis Wiring
1130 Left Side Attachment Pedal Sensor
1138 Boom Cylinder Retract Solenoid
1139 Stick Cylinder Extend Solenoid
1140 Stick Cylinder Retract Solenoid
© 2011 Caterpillar, All Rights Reserved Printed in U.S.A.
1141 Bucket Cylinder Extend Solenoid
1142 Bucket Cylinder Retract Solenoid
1143 Swing Right Solenoid
1144 Swing Left Solenoid
1149 Boom Lowering Check/Modulation Valve Solenoid
1150 Swing Pump Swash Plate Angle Solenoid
1159 Stick Lowering Check/Modulation Valve Solenoid Resistor, Sender and Solenoid Specifications Component Location
1160 Hydraulic Lock Solenoid Part No. Component Description Resistance (Ohms)¹ Schematic Machine Schematic Machine
Component Component
1163 Left Travel Backward Solenoid Position 1: 32 ± 5% Location Location Location Location
1164 Right Travel Backward Solenoid 106-0193 Resistor: Backup
Position 2: 56 ± 5%
Position 3: 35 ± 5%
A/C Unit G-6 65 Sender - Fuel Level B-10 25 Harness And Wire Electrical Schematic Symbols
1165 Right Travel Forward Solenoid Alarm - Action D-1 1 Sender - Hydraulic Temperature B-10 26
Position 4: 35 ± 5%
1166 Left Travel Forward Solenoid 111-9916 Solenoid: Boom Regeneration 11.5 ± 0.5 Alarm - Travel B-6 2 Sensor - Atmospheric Pressure B-11 27 Symbols
1193 Boom Cylinder Extend Solenoid Reversing Fan Alternator E-13 3 Sensor - Boom Cylinder Head Pressure B-11 61
121-1491 Solenoid: 32.0 ± 3.2
1657 Left Joystick Thumbwheel Swing Brake Batteries F-14 4 Sensor - Fuel Temperature B-11 27
Position 1: 10.7 ± 5% Breaker - Alternator G-13 5 Sensor - Load Signal Pressure B-14 69
1658 Right Joystick Thumbwheel T
Position 2: 10.7 ± 5%
1969 Boom Cylinder Head End Pressure Sensor 145-3084 Resistor: Boom Backup Breaker - Main G-13 5 Sensor - Main Pump Pressure B-14 31 Circuit Breaker
Position 3: 10.7 ± 5% Pressure Temperature Level Flow
2103 Boom Circuit Regeneration Solenoid Position 4: 55.0 ± 5% Camera - Rear View E-13 67 Sensor - Overload Warning C-6 29 Symbol Symbol Symbol Symbol Symbol
2269 Stick Circuit Regeneration Solenoid Aux Extend Control - Engine E-14 6 Sensor - Speed F-14 28
Aux Retract
2280 Travel Alarm Relay
Travel RH Rear
Control - Machine E-7 68 Sensor - Swing Pump Pressure B-14 31
51
Symbols and Definitions
2300 Switch Panel Control - Pedal LH I-1 16 Sensor - Water Fuel Level B-9 32
Travel LH Rear
2997 Implement Valve Load Sense Pressure Sensor Control - Pedal RH I-1 17 Service Meter D-1 1 31 Fuse: A component in an electrical circuit that will open the circuit if too much current flows
Stick Retract
3043 Main hydraulic Pump Load Sense Reduction Enable Solenoid Boom Retract Control - Product Link G-7 13 Solenoid - A/C Clutch E-13 3 through it.
148-2350 Solenoid: 5 ± 0.3
3044 Main hydraulic Pump Load Sense Reduction Solenoid Bucket Retract Control - Product Link F-5 12 Solenoid - Aux Extend C-11 35 42
Bucket Extend 70 30 37 Switch (Normally Open): A switch that will close at a specified point (temp, press, etc.). The
Control - Travel Pedal I-1 18 Solenoid - Aux Retract C-11 36
Boom Extend circle indicates that the component has screw terminals and a wire can be disconnected from it.
Stick Extend Control - Wiper D-2 9 Solenoid - Boom Extend C-9 35 57
Travel LH Front Control Handle - LH I-2 11 Solenoid - Boom Regeneration C-11 61 25 26 Switch (Normally Closed): A switch that will open at a specified point (temp, press, etc.).
Travel RH Front Control Handle - RH H-1 11 Solenoid - Boom Retract C-11 36 59 No circle indicates that the wire cannot be disconnected from the component.
Backup Travel RH 32
151-9360 Resistor: 10.7 ± 5% Converter - 12V 10A G-6 10 Solenoid - Bucket Extend C-9 35
Backup Travel LH
Converter - 12V 10A (Communications Radio) E-3 10 Solenoid - Bucket Retract C-11 36 52 Ground (Wired): This indicates that the component is connected to a grounded wire. The
Swing LH
156-2829 Solenoid: 8.3 MAX 34 grounded wire is fastened to the machine.
Swing RH Converter - Radio E-4 10 Solenoid - CWTW Removal Control A-14 37
60
171-0028 Solenoid:
Lowering Check Boom
11.5 ± 0.5 Diode - Backup 1 H-10 5 Solenoid - Float Up Control C-6 61 21 64
Lowering Check Stick 36 35 Ground (Case): This indicates that the component does not have a wire connected to ground.
Diode - Backup 2 I-13 5 Solenoid - Hydraulic Lock PRV B-11 38
HPC On/Off 1 19 47 48 3 It is grounded by being fastened to the machine.
171-3685 Solenoid: 32.6 ± 1 Diode - Backup 3 I-13 5 Solenoid - Lowering Check Boom B-10 39 20 29 69 41
HPC On/Off 2 50 38
174-3016 Resistor: CAN 120 Diode - Backup 4 I-8 5 Solenoid - Lowering Check Stick B-10 39 39 Reed Switch: A switch whose contacts are controlled by a magnet. A magnet closes the
27
Diode - Backup 5 I-8 5 Solenoid - LS Reduce B-14 69 contacts of a normally open reed switch; it opens the contacts of a normally closed reed switch.
189-0189 Solenoid: Neutral Flow Bypass 32.6 ± 1.6 43
Diode - Backup 6 I-8 5 Solenoid - LS Reduce Exchange B-14 69 63 44
239-1134 Solenoid: Start Aid 20 33
Diode - Backup 7 I-8 5 Solenoid - Neutral Flow Bypass C-11 40 Sender: A component that is used with a temperature or pressure gauge. The sender
Empty: 82-85 66 measures the temperature or pressure. Its resistance changes to give an indication to
341-3684 Sender: Fuel Level Sender
Diode - Backup 8 I-8 5 Solenoid - P.S. Pressure B-11 41 40 2
Full: 7.5-9 T
the gauge of the temperature or pressure.
0°C: 20,824 - 25,451 Diode - Backup 9 H-10 5 Solenoid - Reversing Fan B-5 43
Failure Mode Identifiers (FMI)¹ 25°C: 6,134- 7,496 Diode - Backup 10 H-10 5 Solenoid - Start Aid E-13 44 Relay (Magnetic Switch): A rela