Text preview for : 03_disassembly_and_reassemble_E.pdf part of Samsung 03_disassembly_and_reassemble_E Samsung Monitor Monitor T23A950 03_disassembly_and_reassemble_E.pdf
Back to : 03_disassembly_and_reasse | Home
3. Disassembly and Assembly
3. Disassembly and Assembly
This section describes the disassembly and reassembly sequences for this monitor.
As this monitor has parts that are sensitive to static electricity, be careful when
handling them.
3-1. Disassembly
1. Turn the monitor off before beginning the disassembly process.
2. When disassembling the monitor, do not use any metal tools except for the
provided jig.
3. Disassemble the monitor carefully as directed in the following procedures.
Description Photo
1. Separate the front cover from the top
first, pulling in the direction of the arrow.
Internal locking tabs on the front
and back covers.
* These can be broken off easily during
disassembly causing reassembly
impossible.
3-1
3. Disassembly and Assembly
Description Photo
2. Do not disassemble all and put the
monitor down on the table as shown in
the picture.
3-2
3. Disassembly and Assembly
Description Photo
3. Remove the Rear cover from the upper
side.
4. Disconnect the LVDS cable and
function cable from the connector.
3-3
3. Disassembly and Assembly
Description Photo
5. Remove the 12 screws.
Screw
6003-001001
2 EA
6001-001470
5 EA
6001-001114
5 EA
6. Separate the panel from the
BRACKET-PANEL.
3-4
3. Disassembly and Assembly
Description Photo
7. Remove the 4 screws that connects the
HINGE to the BRACKET-PANEL.
Screw
6001-001114
4 EA
3-5
3. Disassembly and Assembly
Description Photo
8. Separate the BRACKET-PANEL from
the Stand.
9. Remove the 7 screws on the bottom
side of the stand.
Screw
6003-001086
7 EA
3-6
3. Disassembly and Assembly
Description Photo
10. Separate the STAND TOP carefully.
Be sure not to bend the TOP when you
take the cover off.
11. Remove the 4 screws on the
BRACKET-PCB.
Screw
6003-000264
4 EA
3-7
3. Disassembly and Assembly
Description Photo
12. Uncover the BRACKET-PCB and make
all of the cables disconnected. Then
separate the main board and the sub
board.
* New type of LVDS connector applied
to 11' model.(Do uble locking)
1. Flip up the locking tab on top of the
connector.
2. Squeeze the edge of the connector
to release the second tab lock and
gently pull the connector away.
13. Remove the Bluetooth and Fan as
shown in the picture.
Screw
6003-000109
3 EA
6003-000282
1 EA
Reassembly procedures are in the reverse order of disassembly procedures.
3-8
3. Disassembly and Assembly
Screw Size
Code No. A (mm) B (mm) C (mm) Q'ty
6001-001114 8 6 4 9 EA
6001-001470 8 3 3 5 EA
6003-000264 6 6 3 4 EA
6003-001001 6 8 3 2 EA
6003-001086 6 12 3 7 EA
6003-000109 5.5 8 2.6 3 EA
6003-000282 6.3 8 3 1 EA
3-9
3. Disassembly and Assembly
3-2. Precautions for Assembly
Description Photo
1. Make HINGE stand perpendicularly
as possible. It can help you assemble
easily.
3-10
3. Disassembly and Assembly
Description Photo
2. Be sure to keep the HINGE stand when
attaching the PANEL to prevent the
STAND TOP from getting speared.
Ensure the bumps on the HINGE
align perfectly with the red-circled
holes before you assemble the ASSY
P-REAR and fasten the screws.
3-11
3. Disassembly and Assembly
Description Photo
3. When you cover the Rear Cover, fit it in
numerical order.
3
2 1
3-12
3. Disassembly and Assembly
3-3. Assembling the ASSY P-REAR
Description Photo
1. Assemble the ASSY P-REAR starting
from the marked area. (Otherwise, the
assembly cannot proceed.)
2. Hook the SNAP marked in the image
into the groove on the ASSY P-REAR.
3. Assemble the ASSY P-REAR by
holding and pressing it at the marked
area with your left hand as shown in
the image.
3-13
3. Disassembly and Assembly
Description Photo
4. Assemble the FRONT into the REAR
starting from the marked area.
5. Assemble the upper part of the REAR.
3-14
3. Disassembly and Assembly
Description Photo
6. Press and fasten the corners of the
REAR in a counterclockwise sequence
as shown in the images.
* Do not pound, but press or wipe,
when fastening the corners.
3-15
3. Disassembly and Assembly
Description Photo
7. Double-check that the assembly is well
done with no area loose, and stand the
SET up.
3-16