Text preview for : GTW-P42M102_[SM].pdf part of Gateway GTW-P42M102 [SM] Gateway GTW-P42M102_[SM].pdf
Back to : GTW-P42M102_[SM].pdf | Home
CONFIDENTIAL
PDP-008-1(Module Format)
Issues:27-Sep-02
Version:1.0
42" PDP DISPLAY
SERVICE MANUAL
MODELGTW-P42M102
CONTENTS
1. IMPORTANT SAFETY PRECAUTIONS ..........1-2
2. SPECIFICATION...............................................2-9
3. FACTORY & ELECTRONIC ADJUSTMENT......3-7
4. BLOCK DIAGRAM..........................................4-1
5. TROUBLE SHOOTING GUIDES......................5-6
6. P.C.BOARD TOP VIEW.................................6-8.
7. ELECTRONIC MODULES LIST.......................7-1
8. EXPLODED VIEW........................................8-1
9. PACKAGING LIST .....................................9-1
IMPORTANT SAFETY PRECAUTIONS VER1.0
1. Before returning an instrument to the customer, always make a safety check of the entire instrument,
including, but not limited to, the following items.
a. Be sure that no built-in protective devices are defective and/or have been defeated during servicing. (1)
Protective shields are provided on this chassis to protect both the technician and the customer. Correctly
replace all missing protective shields, including any removed for servicing convenience. (2) When
reinstalling the chassis and/or other assembly in the cabinet, be sure to put back in place all protective
devices, including, but not limited to, nonmetallic control knobs, insulating fish papers, adjustment and
compartment covers/shields, and isolation resistor/capacitor networks. Do not operate this instrument or
permit it to be operated without all protective devices correctly installed and functioning.
b. Be sure that there are no cabinet openings through which an adult or child might be able to insert their
fingers and contact a hazardous voltage, Such opening include, but are not limited to, (1) spacing
between the picture tube and the cabinet mask, (2) excessively wide cabinet ventilation slots, and (3) an
improperly fitted and/or incorrectly secured cabinet back cover.
--
c. Leakage Current Hot Check--With the instrument completely reassembled, plug the AC line cord directly
into a 120V AC outlet. (Do not use an isolation transformer during this test.) Use a leakage current tester or
a metering system that complies with American National Standards Institutes (ANSI) C101.1 Leakage
Current for Appliances and Underwriters Laboratories (UL) 478. With the instrument AC switch first in the
ON position and then in the OFF position, measure from a known earth ground (metal water pipe, conduit,
etc.) to all exposed metal parts of the instrument (antennas, handle bracket, metal cabinet, screw heads,
metallic overlays, control shafts, etc.), especially any exposed metal parts that offer an electrical return
path to the chassis. Any current measured must not exceed 3.5 milliamp. Reverse the instrument power
cord plug in the outlet and repeat test. ANY MEASUREMENTS NOT WITHIN THE LIMITS SPECIFIED
HEREIN INDICATE A POTENTIAL SHOCK HAZARD THAT MUST BE ELIMINATED BEFORE
RETURNING THE INSTRUMENT TO THE CUSTOMER.
AC Leakage Test (READING
SHOULD NOT
BE ABOVE
LEAKAGE 3.5mA)
CURRENT
TESTER
DEVICE
UNDER + -
TEST
TEST ALL
EXPOSED METAL
SURFACES
3. WIRE CORD
ALSO TEST WITH
PLUG REVERSED EARTH
(USING AC ADAPTER GROUND
PLUG AS REQUIRED)
2. Read and comply with all caution and safety-related notes on or inside the Monitor cabinet, on the
Projection Monitor chassis, or on the picture tube.
--
3. Design Alteration Warning--Do not alter or add to the mechanical or electrical design of this unit. Design
alterations and additions, including, but not limited to, circuit modifications and the addition of the items
such as auxiliary audio and/or video output connections might alter the safety characteristics of this
Projection Monitor and create a hazard to the user. Any design alterations or additions will void the
manufacturer's warranty and will make you, the service, responsible for personal injury or property damage
resulting therefrom.
1-1
IMPORTANT SAFETY PRECAUTIONS VER1.0
--
4. Hot Chassis Warning--a. Some Monitor chassis are electrically connected directly to one conductor of the
AC power cord and may be safely serviced without an isolation transformer only if the AC power plug is
inserted so that the chassis is connected to the ground of the AC power source. To confirm that the AC
power plug is inserted correctly, with an AC voltmeter measure between the chassis and a known earth
ground. If a voltage reading in excess of 1.0V is obtained, remove and reinsert the AC power plug in
opposite polarity and again measure the voltage potential between the chassis and a known earth ground.
b. Some Monitor chassis normally have 85V AC (RMS.), between chassis and earth ground regardless of
the AC plug polarity. These chassis can be safely serviced only with an isolation transformer inserted in the
power line between the receiver and the AC power source, for both personnel and test equipment
protection. c. Some Projection Monitor chassis have a secondary ground systems in addition to the main
chassis ground. This secondary ground system is not isolated from the AC power line. The two-ground
system is electrically separated by insulating material that must not be defeated or altered.
5. Observe original lead dress. Take extra care to assure correct lead dress in the following areas: a. near
sharp edges, b. near thermally hot parts--be sure that leads and components do not touch thermally hot
parts, c. the AC supply, d. high voltage, e. antenna wiring. Always inspect in all areas for pinched, out-of-
place, or frayed wiring. Do not change spacing between components, and between components and the
printed-circuit board. Check AC power cord for damage.
6. Components, parts, and/or wiring that appear to have overheated or are otherwise damaged should be
replaced with components, parts, or wiring that meet original specifications. Additionally, determine the
cause of overheating and/or damage and, if necessary, take corrective action to remove any potential
safety hazard.
--
7. PRODUCT SAFETY NOTICE--Many Monitor electrical and mechanical parts have special safety-related
characteristics some of which are often not evident from visual inspection, nor can the protection they give
necessarily be obtained by replacing them with components rated for higher voltage, wattage, etc. Parts
that have special safety characteristics are identified in this service data by shading with a mark on
schematics and by shading or a mark in the parts list. Use of a substitute replacement part that does
not have the same safety characteristics as the recommended replacement part in this service data parts
list might create shock, fire, and/or other hazards.
1-2
SPECIFICATION FOR GTW-P42M102 PLASMA DISPLAY VER1.0
1. SCOPE:
These specifications describe all the characteristics of the 42 inch color monitor.
2. ELECTRICAL REQUIREMENTS:
2.1. Display panel: Specification
a. Screen size Diagonal 42 inch
b. Aspect ratio 16:9 wide
c. Number of pixels 852(Horizontal, RGB Cells) X 480(Vertical) pixels
d. Pixel Pitch 1.08mm X 1.08mm
e. Luminance 570cd/m2,at APL13%
f. Chromatically