Text preview for : samsung nc10.pdf part of Samsung samsung nc10 Samsung Laptop samsung nc10.pdf
Back to : samsung nc10.pdf | Home
- -
- This Document can not be used without Samsung's authorization -
3. Disassembly and Reassembly
3-1. NC10 Disassembly and assembly
[Caution] Attention to red sentence.
Part Picture Description
1. Before disassembling the system, the AC adapter and the
battery have to be separated.
2. As shown in picture 1, adhere KNOB to the end closely
2 into the arrow direction, then push the battery up as shown
in picture 2.
1 1
3. When the battery is pushed upwards, it can be separated.
Main 4. Remove the BOTTOM screw.
System IF only keboard is disassembled, remove only 3 BOTTOM
screws( mark).
M2 x L8, Silver (15EA)
5. Remove the DOOR-MEMORY.
NC10 3-1
Winchester_NC10_Eng.indb 1 2008-09-20 1:36:02
- -
- This Document can not be used without Samsung's authorization -
3. Disassembly and Reassembly
Part Picture Description
6. Remove the memory by pushing the fixed-tap out.
7. Push the Hook up inwards by using a pin-set as shown in
the picture, and then lift the key board up.
[Notice]
When you push the hook up, you have to be careful not to
scratch Topdp.
As shown in the picture, lift the top side of keyboard up and
then disassemble keyboard.
Main
System
8. Lift the Keyboard up, and then take the FPC out after
lifting the Connector Lock.
Take Keyboard FPC cable out after opening Keyboard
connector Lock.
3-2 NC10
Winchester_NC10_Eng.indb 2 2008-09-20 1:36:13
- -
- This Document can not be used without Samsung's authorization -
3. Disassembly and Reassembly
Part Picture Description
9. As shown in the picture, separate the BOTTOM-
COVER(LAN Connector side first) by widening the gap
between the BOTTOM-COVER and the TOP. (Be careful
not to make scratch in the gap using a wooden-driver.)
As shown in the picture, separate the BOTTOM-COVER
by widening the gap between the BOTTOM-COVER and
the TOP. (Be careful not to make scratch in the gap using a
wooden-driver.)
10. After removing the Screw for fixing HDD remove the
INSULATOR by lifting the HDD up to about 70 degrees
direction.
[Notice]
When you life the HDD up, you shall not enforce excessive
Main
strength.
System
11. Speaker CONN. INT Mic CONN., Power S/W CONN.
Touch-Pad FPC.
NC10 3-3
Winchester_NC10_Eng.indb 3 2008-09-20 1:36:22
- -
- This Document can not be used without Samsung's authorization -
3. Disassembly and Reassembly
Part Picture Description
12. Remove the Antenna Cable which is connected with
wireless LAN, and then remove the Screw which fixes
WLAN. [Aux(Black)]
M2 x L4, Black (1EA)
1. White, Main
2. Black, Aux
13. Remove the Bluetooth Camera Cable and the LCD cable
CONN. and disassemble the W/L Antenna Cable.
14. Remove the Screw which fixes the Main Board and the
TOP and then separate Main Board from TOP.
M2 x L4, Black (2EA)
Main
System
15. Remove the both sides of Screw, which fasten the Hinge
and the TOP.
M2 x L4, Black (4EA)
16. Stand the Top Ass'y in a vertical direction.
3-4 NC10
Winchester_NC10_Eng.indb 4 2008-09-20 1:36:32
- -
- This Document can not be used without Samsung's authorization -
3. Disassembly and Reassembly
Part Picture Description
17. Separate the Top Ass'y from the LCD.
18. Remove the Screw which fixes the SIM Card Sub-board
and the Main-Board, and then separate them.
M2 X L4, Black (2EA)
Main
System
19. Remove the Screw (3 EA) which connects the RHE and
the Main board and separate them.
M2 X L4, Black (3EA)
20. Remove the RHE as shown in the picture.
NC10 3-5
Winchester_NC10_Eng.indb 5 2008-09-20 1:36:41
- -
- This Document can not be used without Samsung's authorization -
3. Disassembly and Reassembly
Part Picture Description
21. Remove the RHE as shown in the picture.
M2 X L4 (4EA)
[Notice]
When you remove the Rubber-LCD-Cap, be careful not to
scratch the Front..
22. Insert your hand into the gap of the LCD Back and the
LCD front and then separate first, the upper part of the
LCD Front and second, the both sides of the LCD Front
then finally the bottom part of it.
M2 X L4 (4EA)
LCD
23. Remove the both sides of Hinge Cover.
Ass'y
24. Conditions after removing the both sides of Hinge Cover.
3-6 NC10
Winchester_NC10_Eng.indb 6 2008-09-20 1:36:42
- -
- This Document can not be used without Samsung's authorization -
3. Disassembly and Reassembly
Part Picture Description
25. Remove the Screw as shown in the picture.
M2 X L4 (4EA)
26. Separate the Hinge and the LCD-Panel as shown in the
picture. (When you separate the Hinge, remove the
Hinge after lifting the LCD-Panel up.)
LCD
Ass'y
27. Dis-assemble the LCD-Cable and then remove the LCD
Panel.
28. Separate the Camera Module and the Cable as shown in
the picture.
NC10 3-7
Winchester_NC10_Eng.indb 7 2008-09-20 1:36:45
- -
- This Document can not be used without Samsung's authorization -
3. Disassembly and Reassembly
Part Picture Description
29. Remove the Tape inside the circle.
30. Pull the LCD cable up to the arrow direction and then
separate it.
21-2. Method to disassemble LCD without disassembling
Main System. As shown in the picture, Stand the Top
Ass'y in a vertical direction. remove 4 Rubber-LCD-
Cap and 4 screws
LCD M2 X L4 (4EA)
Ass'y
22-2. Insert your hand into the gap of the LCD Back and the
LCD front and then separate first, the upper part of the
LCD Front and second, the both sides of the LCD Front
then finally the bottom part of it. After that, remove
screw(4ea) as shown in the picture.
M2 X L4 (4EA)
22-3. As shown in the picture, LCD can be disassembled
from LCD Cable and Camera moduel also can be
disassembled.
LCD Cable and Camera moduel disassembling method
refer to No 28.
3-8 NC10
Winchester_NC10_Eng.indb 8 2008-09-20 1:36:56
- -
- This Document can not be used without Samsung's authorization -
3. Disassembly and Reassembly
Part Picture Description
31. Remove the Bluetooth Module.
32. Remove the Speaker Cable and the Speaker.
TOP
Ass'y
33. Remove the MIC.
34. Remove the Molding.
NC10 3-9
Winchester_NC10_Eng.indb 9 2008-09-20 1:37:02
- -
- This Document can not be used without Samsung's authorization -
3. Disassembly and Reassembly
Part Picture Description
35. Remove the Power S/W Ass'y.
36. Confirm the arrow mark for assembly direction on the
Power S/W Sub board.
TOP
Ass'y 37. Check the Guide in which the Power S/W at bottom will
be inserted, then you have to assemble the Power S/W.
3-10 NC10
Winchester_NC10_Eng.indb 10 2008-09-20 1:37:04
- -
- This Document can not be used without Samsung's authorization -
3. Disassembly and Reassembly
Part Picture Description
38. Remove the Touch-PAD FFC (BA41-00972A, BA41-
00973A).
39. Remove the Shield-Touch PAD (BA81-05892A).
TOP
Ass'y
40. Remove the Touch-Pad (BA58-02418A).
41. During assembly, check the arrow direction, and then
assemble the Touch