Text preview for : hfe_fostex_d-160_supp_en.pdf part of FOSTEX hfe fostex d-160 supp en FOSTEX Audio D-160 hfe_fostex_d-160_supp_en.pdf
Back to : hfe_fostex_d-160_supp_en. | Home
D-160 Owner's Manual Supplement (V2.10)
The functions explained here are additions to the main manual because of our version-up
(V2.10) of the D-160 software. Please read this manual together with the main manual
before operating the D-160.
1. Large capacity hard disks can now be used.
It is now possible to use E-IDE hard disks with a recording capacity up to approximately
30GB (FS=44.1kHz) as the D-160's recording media (current drive/backup drive).
Please refer to "List of hard disks checked for operation" to make sure any product you
are about to use will operate correctly.
: When formatting a large capacity hard disk, the time required to format will be in
relation to disk size. As a general estimate, it requires about 15 minutes to format 1GB and
thus, as an example, it will take about 7 hours for a 30GB hard disk.
Maker Model Disk Capacity
Fireball CX 6.4GB, 10.2GB, 13.0GB, 20.4GB
Quantum
Fireball CR 4.3GB, 6.4GB, 8.4GB, 13.0GB
2. In the BAR/BEAT/CLK (bar/beat/clock) time base, the offset figure of the BAR
that indicates the head of the disk can now be edited.
Although [Time Base] is explained in [Before Operating] the main D-160 owners manual,
the unit to indicate the present traveling position, MTC (MIDI time code) or BAR/BEAT/
CLK (bar/beat/clock) is now also employed in addition to ABS (absolute time).
Because of this, the figure indicating the present disk position will be different depending
on the selected time base. When the D-160 is in the initial setup state and the MTC offset
display at [MTC 00h 59m 57s 00f] for the disk in the head position (ABS 00m 00s 00f) or,
at BAR/BEAT/CLK, it will display [-002bar 1 beat 00clk].
Before version-up V2.10, this offset figure could be changed only for MTC, and the BAR/
BEAT/CLK offset figure was fixed to [-002bar 1beat 00clk].
But, with V2.10, the BAR offset figure in BAR/BEAT/CLK can now be changed to any
figure within the -002 ~ -009 range.
In the initial setup state of the D-160, [-002bar 1beat 00clk] will always be displayed and
the bar offset figure will be [-002bar].
To setup the offset figure of this BAR/BEAT/CLK display, execute it in the SETUP mode of
the D-160, the same as the setup of the MTC offset figure. Please read the reverse side
operating procedures. For setup of the MTC offset, refer to the explanations in the SETUP
mode of the main owners manual.
Setup procedures for BAR/BEAT/CLK offset
: Offset setups can be executed for each program. The setup content will be
maintained even though power is switched off.
1. First select the program to which offset is to be setup. 4. Rotate the JOG dial counter-clockwise.
The example below is the display as a result of selecting The offset figure of the current set bar will be
program 1. displayed. If it is in the initial state, [-002bar Offset?]
will be displayed as shown below.
ABS
OL SETUP
0
3
6
9 44.1kHz
12 OL
18 0
3 SIGNATURE
24
30 6
42 9 44.1kHz
12
18
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 24
30
42
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
Blink
2. After switching to the SETUP display by pressing the
DISP SEL key, press the EXECUTE/YES key.
If the DISP SEL key is pressed twice against the above
OL
0
3
6
9 44.1kHz
12
18
ABS display, it will change to the SETUP display and if
24
30
42
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
the EXECUTE/YES key is pressed, it will change to the
[Drive Sel ? (current drive setup)] menu as shown
5. Press the EXECUTE/YES key.
below when in the initial setup state.
Blink The number [2] in -002bar will blink and the bar
offset figure can now be edited.
SETUP
DISP SEL
OL
0
3
Blink
6
9 44.1kHz
12
18
24
30
42
EXECUTE
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
/ YES
OL
0
3
6
9 44.1kHz
12
18
24
30
42
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
EXECUTE SETUP
/ YES OL
0
3
6
9 44.1kHz
12
18
24
30
42
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
6. Rotate the JOG dial to input the desired offset figure,
then press the EXECUTE/YES key.
Blink
Any offset figure within a 2~9 range can be input
(the example below is the result of inputting of 5 for
3. Rotate the JOG dial to show [Signature Set?] in the the bar figure). After this, press the EXECUTE/YES
display and press the EXECUTE/YES key. key and it will be set to the input offset figure and the
The current set bar will be displayed and if it is in the display will change to the [Signature Set?] menu.
initial setup state, the first bar will be 4/4.
Blink
OL
0
3
6
9 44.1kHz
12
18
SETUP 24
30
42
OL
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
3
6
9 44.1kHz
12
18
24
30
42
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
EXECUTE SETUP
/ YES
OL
0
3
6
9 44.1kHz
12
18
24
EXECUTE SETUP 30
42
/ YES OL
0
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
3 SIGNATURE
6
9 44.1kHz
12
18
24
30
42 Blink
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
7. Exit from the SETUP mode by pressing the EXIT/NO
key.