Text preview for : C800.PDF part of Dell C800 Dell Laptop C800.PDF
Back to : C800.PDF | Home
Dell Latitude C800 Service Manual
DellTM LatitudeTM C800 Service Manual
Before You Begin
Preparing to Work Inside the Computer
Recommended Tools
Screw Identification
Removing and Replacing Parts
System Components
Hard Drive
Fixed Optical Drive
Memory Module
Mini PCI Card Assembly
Keyboard Assembly
Display and Bezel Assemblies
Microprocessor Thermal Cooling Assembly
Microprocessor Module
Video Graphics Board
Palmrest Assembly
Reserve Battery
System Board Assembly
Battery and Modular Bay Latch Assemblies
Battery Charger Board
LED Board
Fan Assembly
RJ-11/RJ-45 Board
Notes, Notices, and Cautions
NOTE: A NOTE indicates important information that helps you make better use
of your computer system.
NOTICE: A NOTICE indicates either potential damage to hardware or loss of
data and tells you how to avoid the problem.
file:///F|/Service%20Manuals/Dell/Latitude/c800/index.htm (1 of 2) [2/28/2004 8:00:00 AM]
Before You Begin : Dell Latitude C800 Service Manual
Back to Contents Page
Before You Begin
DellTM LatitudeTM C800 Service Manual
Preparing to Work Inside the Computer
Recommended Tools
Screw Identification
Preparing to Work Inside the Computer
NOTICE: Only a certified service technician should perform repairs on your
computer. Damage due to servicing that is not authorized by Dell is not covered
by your warranty.
NOTICE: To avoid damaging the computer, perform the following steps before
you begin working inside the computer.
1. Make sure that the work surface is flat and clean to prevent scratching the
computer cover.
2. Save any work in progress and close all open application programs.
3. Turn off the computer and all attached devices.
NOTE: Before turning off the computer, make sure the computer is not in a
power-management mode.
4. Make sure the computer is undocked.
5. Disconnect the computer from the electrical outlet.
6. To avoid possible damage to the system board, wait 10 to 20 seconds and then
disconnect any attached devices.
7. Disconnect all other external cables from the computer.
file:///F|/Service%20Manuals/Dell/Latitude/c800/ch1.htm (1 of 6) [2/28/2004 8:00:10 AM]
Before You Begin : Dell Latitude C800 Service Manual
8. Remove any installed PC Cards or plastic blanks from the PC Card slot.
9. Close the display and turn the computer upside down on a flat work surface.
10. Remove the battery from the battery bay.
NOTICE: To avoid component damage, always remove any installed batteries
before you service the computer.
11. Remove any device installed in the modular bay.
12. To dissipate static electricity while you work, periodically touch an unpainted
metal surface on the computer chassis.
13. Handle components and cards by their edges, and avoid touching pins and
contacts.
Recommended Tools
The procedures in this manual require the following tools:
q #1 magnetized Phillips screwdriver
q Small flat-blade screwdriver
q Small plastic scribe
q Microprocessor extractor
q Nonmarring tool
q Flash BIOS upgrade program diskette or CD (provided when needed to upgrade
the system BIOS)
System Orientation
file:///F|/Service%20Manuals/Dell/Latitude/c800/ch1.htm (2 of 6) [2/28/2004 8:00:10 AM]
Before You Begin : Dell Latitude C800 Service Manual
Screw Identification
When you are removing and replacing components, photocopy the placemat as a tool
to lay out and keep track of the component screws.The placemat provides the number
of screws and the sizes.
Screw Identification
file:///F|/Service%20Manuals/Dell/Latitude/c800/ch1.htm (3 of 6) [2/28/2004 8:00:10 AM]
Before You Begin : Dell Latitude C800 Service Manual
NOTICE: When reinstalling a screw, you must use a screw of the correct
diameter and length. Make sure that the screw is properly aligned with its
corresponding hole, and avoid overtightening.
Screw Placement Map
Hard Drive Door Security: Keyboard to Bottom Case Display to Base:
Assembly:
M3.0 x 5 mm (1 each) M2.5 x 6 mm (3
M2.5 x 20 mm (4 each; one in each; 2 at back of
memory door and one in mini- system; 1 at flex
PCI door) cable strain relief)
file:///F|/Service%20Manuals/Dell/Latitude/c800/ch1.htm (4 of 6) [2/28/2004 8:00:10 AM]
Before You Begin : Dell Latitude C800 Service Manual
Display Bezel: Display Panel to Display Video Graphics
Mounting Bracket: Board:
Rubber screw covers (4 each)
M2.0 x 3 mm(6 each) M2.5 x 8 (3 each)
Plastic screw covers (2 each)
M2.5 x 4 mm (6 each)
Flex Cable Mounting Bracket to
Top Cover:
M2.5 x 4 mm (1 each)
Palmrest to System Board: LED Board:
Bottom Case Assembly:
M2.5 x 4 mm captive washer M2.0 x 4 mm (2
M2.5 x 20 mm (9 each) (3 each) each)
Palmrest Bracket:
M2.5 x 4 mm (2 each) M2.5 x 20 mm (1 each)
Fan Assembly: RJ-11/RJ-45 Board Assembly:
M2.0 x 4 mm (3 each) M2.5 x 4 mm (1 each)
Back to Contents Page
file:///F|/Service%20Manuals/Dell/Latitude/c800/ch1.htm (5 of 6) [2/28/2004 8:00:10 AM]
Before You Begin : Dell Latitude C800 Service Manual
file:///F|/Service%20Manuals/Dell/Latitude/c800/ch1.htm (6 of 6) [2/28/2004 8:00:10 AM]
Removing and Replacing Parts : Dell Latitude C800/C805 Service Manual
Back to Contents Page
Removing and Replacing Parts
DellTM LatitudeTM C800/C805 Service Manual
System Components Video Graphics Board
Hard Drive Palmrest Assembly
Fixed Optical Drive Reserve Battery
Memory Module System Board Assembly
Mini PCI Card Assembly Battery and Modular Bay Latch
Assemblies
Keyboard Assembly
Battery Charger Board
Display and Bezel Assemblies
LED Board
Microprocessor Thermal Cooling
Assembly Fan Assembly
Microprocessor Module RJ-11/RJ-45 Board
System Components
Exploded View
file:///F|/Service%20Manuals/Dell/Latitude/c800/ch2.htm (1 of 49) [2/28/2004 8:00:16 AM]
Removing and Replacing Parts : Dell Latitude C800/C805 Service Manual
file:///F|/Service%20Manuals/Dell/Latitude/c800/ch2.htm (2 of 49) [2/28/2004 8:00:16 AM]
Removing and Replacing Parts : Dell Latitude C800/C805 Service Manual
NOTICE: Only a certified service technician should perform repairs on your
computer. Damage due to servicing that is not authorized by Dell is not covered by
your warranty.
NOTICE: Unless otherwise noted, each procedure in this manual assumes that a
part can be replaced by performing the removal procedure in reverse order.
Hard Drive
NOTICE: Disconnect the computer and attached devices from the electrical outlet
and remove any installed batteries.
NOTICE: To avoid ESD, ground yourself by using a wrist grounding strap or by
periodically touching unpainted metal on the computer.
NOTICE: The hard drive is very sensitive to shock. Handle it by its edges (do not
squeeze the top of the case), and avoid dropping it.
Hard Drive
file:///F|/Service%20Manuals/Dell/Latitude/c800/ch2.htm (3 of 49) [2/28/2004 8:00:16 AM]
Removing and Replacing Parts : Dell Latitude C800/C805 Service Manual
Removing the Hard Drive
1. Follow the instructions in "Preparing to Work Inside the Computer."
2. Remove the drive door screw.
3. Pull the hard drive out.
Replacing the Hard Drive
1. Gently push the hard drive into the drive bay until the drive door is flush with the
computer case.
2. Push down on the drive until it snaps into place.
3. Replace the screw in the hard drive door.
file:///F|/Service%20Manuals/Dell/Latitude/c800/ch2.htm (4 of 49) [2/28/2004 8:00:16 AM]
Removing and Replacing Parts : Dell Latitude C800/C805 Service Manual
Fixed Optical Drive
NOTICE: Disconnect the computer and attached devices from the electrical outlet
and remove any installed batteries.
NOTICE: To avoid ESD, ground yourself by using a wrist grounding strap or by
periodically touching unpainted metal on the computer.
Fixed Optical Drive
Removing the Fixed Optical Drive
1. Follow the instructions in "Preparing to Work Inside the Computer."
2. Loosen the captive screw on the bottom of the computer.
file:///F|/Service%20Manuals/Dell/Latitude/c800/ch2.htm (5 of 49) [2/28/2004 8:00:16 AM]
Removing and Replacing Parts : Dell Latitude C800/C805 Service Manual
NOTICE: To keep the pull tab from catching on the captive screw, turn the
computer over before removing the fixed optical drive.
3. Turn the computer over, pull out the pull tab, and use the pull tab to remove the
fixed optical drive.
Memory Module
NOTICE: Disconnect the computer and any attached devices from electrical outlets
and remove any installed batteries.
NOTICE: To avoid ESD, ground yourself by using a wrist grounding strap or by
periodically touching unpainted metal on the computer.
Removing the Memory Module Cover
Memory Module Cover
file:///F|/Service%20Manuals/Dell/Latitude/c800/ch2.htm (6 of 49) [2/28/2004 8:00:16 AM]
Removing and Replacing Parts : Dell Latitude C800/C805 Service Manual
1. Follow the instructions in "Preparing to Work Inside the Computer."
2. Remove the screw.
3. Disengage the metal tabs at the opposite end of the cover.
Memory Modules
file:///F|/Service%20Manuals/Dell/Latitude/c800/ch2.htm (7 of 49) [2/28/2004 8:00:16 AM]
Removing and Replacing Parts : Dell Latitude C800/C805 Service Manual
Removing the Memory Modules
1. Remove the memory module cover.
2. To release a memory module from its socket, spread apart the tabs at each side of
the module until the module pops up slightly.
3. Lift the memory module out of its socket.
Replacing the Memory Modules
1. If you only have one memory module, install it in the socket labeled "DIMM A."
Install a second memory module in the socket labeled "DIMM B."
NOTE: Memory modules are keyed to fit into their sockets in only one direction.
file:///F|/Service%20Manuals/Dell/Latitude/c800/ch2.htm (8 of 49) [2/28/2004 8:00:16 AM]
Removing and Replacing Parts : Dell Latitude C800/C805 Service Manual
2. Insert the memory module's edge connector into the socket slot at a 45-degree
angle and press the module firmly into the slot.
3. Pivot the module down until it clicks into place. If you do not hear a click, remove
the module and reinstall it.
4. Insert the metal tabs on the memory module cover into the bottom case assembly,
rotate the cover down, and replace the screw.
Mini PCI Card Assembly
You must remove the optional Mini PCI Card assembly before the system board assembly
can be removed. A Mini PCI Card assembly may consist of a modem, a NIC, a modem and
NIC combination, or a wireless NIC. A modem, NIC, or modem and NIC combination must
be connected to the wiring harness as appropriate; a wireless NIC must be connected to
the system's internal antenna.
NOTICE: Disconnect the computer and attached devices from electrical outlets and
remove any installed batteries.
NOTICE: To avoid ESD, ground yourself by using a wrist grounding strap or by
periodically touching unpainted metal on the computer.
Mini PCI Card Cover
file:///F|/Service%20Manuals/Dell/Latitude/c800/ch2.htm (9 of 49) [2/28/2004 8:00:16 AM]
Removing and Replacing Parts : Dell Latitude C800/C805 Service Manual
Removing the Mini PCI Card Assembly
1. Follow the instructions in "Preparing to Work Inside the Computer."
2. Remove the Mini PCI Card cover.
3. To release the Mini PCI Card assembly, spread the metal securing tabs until the
assembly pops up slightly.
4. Disconnect the assembly from the wiring harness or internal antenna.
5. Lift out the assembly and disconnect any attached cables.
Replacing the Mini PCI Card Assembly
1. Align the Mini PCI Card assembly with the socket at a 45-degree angle, and press
the Mini PCI Card into the socket.
2. Depending on what type of Mini PCI Card you are installing, either connect the wiring
file:///F|/Service%20Manuals/Dell/Latitude/c800/ch2.htm (10 of 49) [2/28/2004 8:00:16 AM]
Removing and Replacing Parts : Dell Latitude C800/C805 Service Manual
harness to the Mini PCI Card assembly, or connect the mini-coax antenna cable from
the Mini PCI Card assembly to the internal antenna.
NOTICE: The connectors are keyed for correct insertion; do not force the
connections.
Mini PCI Card Assembly Using Wiring Harness
Mini-PCI Wireless NIC Assembly Using Antenna Cable
file:///F|/Service%20Manuals/Dell/Latitude/c800/ch2.htm (11 of 49) [2/28/2004 8:00:16 AM]
Removing and Replacing Parts : Dell Latitude C800/C805 Service Manual
NOTICE: If a wireless NIC card contains two mini-coax antenna connectors, connect
the mini-coax antenna cable to the outermost antenna connector on the card as
shown.
NOTICE: If you are installing a wireless NIC, fold and tuck the unused wiring
harness into the slot so it does not interfere with the cover.
3. Pivot the Mini PCI Card assembly down until it clicks into place.
4. Replace the Mini PCI Card assembly cover.
Keyboard Assembly
file:///F|/Service%20Manuals/Dell/Latitude/c800/ch2.htm (12 of 49) [2/28/2004 8:00:16 AM]
Removing and Replacing Parts : Dell Latitude C800/C805 Service Manual
NOTICE: Disconnect the computer and attached devices from electrical outlets and
remove any installed batteries.
NOTICE: To avoid ESD, ground yourself by using a wrist grounding strap or by
periodically touching unpainted metal on the computer.
Keyboard Screws
Removing the Keyboard Assembly
1. Follow the instructions in "Preparing to Work Inside the Computer."
2. Turn the computer over and remove the four screws labeled with a "circle K."
3. Turn the computer over and open the display.
file:///F|/Service%20Manuals/Dell/Latitude/c800/ch2.htm (13 of 49) [2/28/2004 8:00:16 AM]
Removing and Replacing Parts : Dell Latitude C800/C805 Service Manual
NOTICE: Be careful when handling the keyboard. The keycaps are fragile, easily
dislodged, and time-consuming to replace.
4. Use a nonmarring tool under the blank key to pry up the keyboard.
Keyboard Removal
5. Lift the right end of the keyboard and slide it slightly toward the right side of the
computer to disengage the tabs at the left end.
file:///F|/Service%20Manuals/Dell/Latitude/c800/ch2.htm (14 of 49) [2/28/2004 8:00:16 AM]
Removing and Replacing Parts : Dell Latitude C800/C805 Service Manual
6. Pivot the keyboard and balance it upright on the left side of the computer.
Keyboard Cable
7. Disconnect the keyboard cable and lay the keyboard assembly aside.
Replacing the Keyboard Assembly
1. While bracing the keyboard assembly upright on its left end, connect the keyboard
cable to the interface connector on the system board.
file:///F|/Service%20Manuals/Dell/Latitude/c800/ch2.htm (15 of 49) [2/28/2004 8:00:16 AM]
Removing and Replacing Parts : Dell Latitude C800/C805 Service Manual
NOTICE: Position the keyboard/track stick flex cable so it is not pinched when you
replace the keyboard in the bottom case assembly.
2. Insert the metal tabs at the left end of the keyboard under the edge of the bottom
case assembly, and fit the keyboard into place.
3. Check that the keyboard is correctly installed. The keys should be flush with the left
and right surfaces of the palmrest.
4. Reinstall the four screws in the holes labeled "circle K."
Display and Bezel Assemblies
NOTICE: Disconnect the computer and attached devices from electrical outlets and
remove any installed batteries.
NOTICE: To avoid ESD, ground yourself by using a wrist grounding strap or by
periodically touching unpainted metal on the computer.
Display Assembly
file:///F|/Service%20Manuals/Dell/Latitude/c800/ch2.htm (16 of 49) [2/28/2004 8:00:16 AM]
Removing and Replacing Parts : Dell Latitude C800/C805 Service Manual
Removing the Hinge Cover
Hinge Cover
file:///F|/Service%20Manuals/Dell/Latitude/c800/ch2.htm (17 of 49) [2/28/2004 8:00:16 AM]
Removing and Replacing Parts : Dell Latitude C800/C805 Service Manual
1. Follow the instructions in "Preparing to Work Inside the Computer."
2. Use a nonmarring tool to loosen the hinge cover at the back and at each side of the
computer.
3. Open the display and lift off the hinge cover.
Removing the Display Assembly
Display Assembly
file:///F|/Service%20Manuals/Dell/Latitude/c800/ch2.htm (18 of 49) [2/28/2004 8:00:16 AM]
Removing and Replacing Parts : Dell Latitude C800/C805 Service Manual
1. Remove the hinge cover.
NOTICE: Make sure you remove the flex cable before you remove the display
assembly.
Flex Cable
file:///F|/Service%20Manuals/Dell/Latitude/c800/ch2.htm (19 of 49) [2/28/2004 8:00:16 AM]
Removing and Replacing Parts : Dell Latitude C800/C805 Service Manual
2. Remove the 6-mm screw that secures the display flex cable to the strain relief, and
then use the pull loop to remove the display flex cable from the graphics card.
NOTICE: When reconnecting the flex cable, press down on both ends of the
connector, not in the middle. Pressing the middle of the connector can damage
fragile components.
3. Open the display and, from the back of the computer, remove the two screws
labeled with a "circle D" that secure the display assembly to the bottom case
assembly.
4. With the display in an upright position, lift the display assembly from the bottom
case assembly.
Display Assembly Bezel and Panel
file:///F|/Service%20Manuals/Dell/Latitude/c800/ch2.htm (20 of 49) [2/28/2004 8:00:16 AM]
Removing and Replacing Parts : Dell Latitude C800/C805 Service Manual
Removing the Display Assembly Bezel
1. Use a scribe to pry out the four rubber screw covers located across the top of the
bezel.
file:///F|/Service%20Manuals/Dell/Latitude/c800/ch2.htm (21 of 49) [2/28/2004 8:00:16 AM]
Removing and Replacing Parts : Dell Latitude C800/C805 Service Manual
2. Remove the four 4-mm screws located across the top of the bezel.
3. Use a scribe at the indentations to pry out the two plastic screw covers located at
the bottom of the bezel.
4. Remove the two 4-mm screws located at the bottom of the bezel.
5. Separate the bezel from the display-assembly top cover.
The bezel is secured to the display assembly top cover with plastic tabs around the
sides. Use a plastic scribe to help separate the bezel from the top cover.
Removing the Display Panel
1. Remove the hinge cover.
2. Detach the display flex cable from the strain relief and the graphics card.
3. Remove the display assembly bezel.
4. Remove the 4-mm screw securing the plastic flex cable mounting bracket to the top
cover assembly.
5. Remove the six 3-mm screws (three on each side) from the right and left sides of
the panel.
6. Lift the display panel and flex cable out of the top cover assembly.
7. Disconnect the flex cable from the two connectors (a ZIF and a standard connector)
on the display panel assembly.
Flex Cable Connectors on Display Panel
file:///F|/Service%20Manuals/Dell/Latitude/c800/ch2.htm (22 of 49) [2/28/2004 8:00:16 AM]
Removing and Replacing Parts : Dell Latitude C800/C805 Service Manual
Replacing the Display Panel
NOTE: Use a magnetic screwdriver to reassemble the display panel in the display.
1. Connect the flex cable to the two connectors on the back of the display panel.
2. Place the display panel assembly in the top cover, taking care that the flex cable is in
place and is not crushed or crimped.
file:///F|/Service%20Manuals/Dell/Latitude/c800/ch2.htm (23 of 49) [2/28/2004 8:00:16 AM]
Removing and Replacing Parts : Dell Latitude C800/C805 Service Manual
3. Reinstall the 4-mm screw that secures the flex cable mounting bracket to the top
cover.
4. Starting on the left side, use a magnetic screwdriver to reinstall the six 3-mm screws
that secure the display panel in the top cover.
5. Reinstall the display flex cable strain-relief screw and reconnect the flex cable to the
graphics card.
6. Reinstall the display assembly bezel.
Removing the Display Latch
Removing the Display Latch
1. Remove the hinge cover.
2. Detach the display flex cable from the strain relief and the graphics card.
3. Remove the display assembly bezel.
file:///F|/Service%20Manuals/Dell/Latitude/c800/ch2.htm (24 of 49) [2/28/2004 8:00:16 AM]
Removing and Replacing Parts : Dell Latitude C800/C805 Service Manual
4. Remove the display panel from the top cover.
5. Remove the display latch by unsnapping the latch and captive spring.
Microprocessor Thermal Cooling Assembly
NOTICE: Disconnect the computer and attached devices from electrical outlets and
remove any installed batteries.
NOTICE: To avoid ESD, ground yourself by using a wrist grounding strap or by
periodically touching unpainted metal on the computer.
Retaining Clip
Removing the Microprocessor Thermal Cooling
file:///F|/Service%20Manuals/Dell/Latitude/c800/ch2.htm (25 of 49) [2/28/2004 8:00:16 AM]
Removing and Replacing Parts : Dell Latitude C800/C805 Service Manual
Assembly
1. Follow the instructions in "Preparing to Work Inside the Computer."
2. Remove the keyboard.
3. Remove the hinge cover.
4. Insert a flat-blade screwdriver into the latch mechanism at the left side of the
microprocessor retaining clip. Pry open the clip by pivoting the top of the screwdriver
toward the right side of the computer.
Microprocessor Thermal Cooling Assembly
NOTICE: To ensure maximum cooling for the microprocessor, do not touch the heat
transfer areas on the microprocessor thermal cooling assembly. The oils in your skin
reduce the heat transfer capability of the thermal pads.
5. Lift out the thermal cooling assembly.
file:///F|/Service%20Manuals/Dell/Latitude/c800/ch2.htm (26 of 49) [2/28/2004 8:00:16 AM]
Removing and Replacing Parts : Dell Latitude C800/C805 Service Manual
Microprocessor Module
NOTICE: Disconnect the computer and attached devices from electrical outlets and
remove any installed batteries.
NOTICE: To avoid ESD, ground yourself by using a wrist grounding strap or by
periodically touching unpainted metal on the computer.
Microprocessor Module
Removing the Microprocessor Module
1. Follow the instructions in "Preparing to Work Inside the Computer."
2. Remove the keyboard.
3. Remove the hinge cover.
file:///F|/Service%20Manuals/Dell/Latitude/c800/ch2.htm (27 of 49) [2/28/2004 8:00:16 AM]
Removing and Replacing Parts : Dell Latitude C800/C805 Service Manual
NOTICE: To ensure maximum cooling for the microprocessor, do not touch the heat
transfer areas on the thermal cooling assembly. The oils in your skin reduce the heat
transfer capability of the thermal pads.
4. Remove the microprocessor thermal cooling assembly.
NOTICE: When removing the microprocessor module, pull the module straight up.
Do not bend the pins.
5. Remove the microprocessor module.
NOTICE: To avoid damage to the microprocessor, hold the screwdriver so that it is
perpendicular to the microprocessor when removing the cam lock screw (see
"Microprocessor Cam Lock Screw").
a. Loosen the microprocessor socket cam lock screw. The location of the screw
and the rotation direction may vary with the socket manufacturer; look for
small icons indicating open and locked positions.
Microprocessor Cam Lock Screw (Example)
NOTICE: Hold the microprocessor down while turning the cam lock screw to prevent
intermittent contact between the cam lock screw and microprocessor.
file:///F|/Service%20Manuals/Dell/Latitude/c800/ch2.htm (28 of 49) [2/28/2004 8:00:16 AM]
Removing and Replacing Parts : Dell Latitude C800/C805 Service Manual
b. Use the microprocessor extraction tool to remove the microprocessor module.
Replacing the Microprocessor Module
NOTICE: If you received a flash BIOS update program diskette or CD with the
replacement microprocessor, you must update the BIOS after replacing the
microprocessor module. For instructions on updating or reflashing the BIOS, see the
Dell Portable Computer BIOS Update Guide.
NOTICE: Proper seating of the microprocessor module does not require force.
NOTICE: A microprocessor module that is not properly seated can result in an
intermittent connection and subsequent failures.
1. Align the pin-1 triangle on the microprocessor toward the pin-1 triangle in the
socket, insert the microprocessor into the socket, and move it around slightly until
you feel it settle into the socket.
When the microprocessor module is correctly seated, all four corners are aligned to
the same height. If one or more corners of the module are higher than the others, the
module is not seated correctly.
file:///F|/Service%20Manuals/Dell/Latitude/c800/ch2.htm (29 of 49) [2/28/2004 8:00:16 AM]
Removing and Replacing Parts : Dell Latitude C800/C805 Service Manual
NOTICE: Hold the microprocessor down while turning the cam lock screw to prevent
intermittent contact between the cam lock screw and microprocessor (see
"Microprocessor Cam Lock Screw").
2. Tighten the cam lock screw.
NOTICE: Do not over- or undertighten the screw. Tighten it until the screw indicator
points to the "closed" or "locked" indicator on the socket.
3. Replace the microprocessor thermal cooling assembly.
Closing the Microprocessor Retaining Clip
4. While pressing lightly down on the center of the retaining clip, insert a flat-blade
screwdriver into the latch mechanism and pivot the top of the screwdriver away from
file:///F|/Service%20Manuals/Dell/Latitude/c800/ch2.htm (30 of 49) [2/28/2004 8:00:16 AM]
Removing and Replacing Parts : Dell Latitude C800/C805 Service Manual
the clip to close the latch.
Video Graphics Board
NOTICE: Disconnect the computer and attached devices from electrical outlets and
remove any installed batteries.
NOTICE: To avoid ESD, ground yourself by using a wrist grounding strap or by
periodically touching unpainted metal on the computer.
Video Graphics Board
Removing the Video Graphics Board
1. Follow the instructions in "Preparing to Work Inside the Computer."
file:///F|/Service%20Manuals/Dell/Latitude/c800/ch2.htm (31 of 49) [2/28/2004 8:00:16 AM]
Removing and Replacing Parts : Dell Latitude C800/C805 Service Manual
2. Remove the keyboard.
3. Remove the hinge cover.
4. Detach the display flex cable from the strain relief and the graphics card.
5. Remove the three 8-mm screws that secure the video graphics board.
6. Separate the video graphics board from the system board connector.
Replacing the Video Graphics Board
1. Align the three screw holes and press down firmly on the word "Dell" to seat the
board in its connector.
NOTICE: Make sure the board is correctly and firmly seated before continuing.
Failure to do so will cause intermittent video failures.
2. Replace the three screws.
Palmrest Assembly
NOTICE: Disconnect the computer and attached devices from electrical outlets and
remove any installed batteries.
NOTICE: To avoid ESD, ground yourself by using a wrist grounding strap or by
periodically touching unpainted metal on the computer.
Palmrest Assembly
file:///F|/Service%20Manuals/Dell/Latitude/c800/ch2.htm (32 of 49) [2/28/2004 8:00:16 AM]
Removing and Replacing Parts : Dell Latitude C800/C805 Service Manual
NOTICE: The reserve battery provides power to the computer's time RTC and
NVRAM when the computer is turned off. Removing the palmrest disconnects the
reserve battery and causes the computer to lose the date and time information as
well as all user-specified parameters in NVRAM. If possible, make a copy of this
information before you disconnect the reserve battery.
Removing the Palmrest Assembly
1. Follow the instructions in "Preparing to Work Inside the Computer."
2. Remove the hard drive and the fixed optical drive.
3. Remove the keyboard.
4. Remove the hinge cover.
5. Remove the display assembly.
file:///F|/Service%20Manuals/Dell/Latitude/c800/ch2.htm (33 of 49) [2/28/2004 8:00:16 AM]
Removing and Replacing Parts : Dell Latitude C800/C805 Service Manual
NOTICE: To avoid damaging the palmrest assembly, you must first remove the
display assembly.
6. Turn the computer over.
7. Remove the nine 20-mm screws (labeled with a "circle P") that secure the palmrest
to the computer.
Palmrest Screws
8. Turn the computer over.
9. Use the pull loop to disconnect the palmrest flex cable from the touch- pad connector
on the system board.
file:///F|/Service%20Manuals/Dell/Latitude/c800/ch2.htm (34 of 49) [2/28/2004 8:00:16 AM]
Removing and Replacing Parts : Dell Latitude C800/C805 Service Manual
10. Carefully lift out the palmrest assembly.
Reserve Battery
NOTICE: Disconnect the computer and attached devices from electrical outlets and
remove any installed batteries.
NOTICE: To avoid ESD, ground yourself by using a wrist grounding strap or by
periodically touching unpainted metal on the computer.
Reserve Battery
NOTICE: The reserve battery provides power to the computer's RTC and NVRAM
when the computer is turned off. Removing the battery causes the computer to lose
the date and time information as well as all user-specified parameters in NVRAM. If
possible, make a copy of this information before you remove the reserve battery.
file:///F|/Service%20Manuals/Dell/Latitude/c800/ch2.htm (35 of 49) [2/28/2004 8:00:16 AM]
Removing and Replacing Parts : Dell Latitude C800/C805 Service Manual
Removing the Reserve Battery
1. Follow the instructions in "Preparing to Work Inside the Computer."
2. Remove the keyboard.
3. Remove the hinge cover.
4. Remove the display assembly.
5. Remove the palmrest assembly.
6. On the underside of the palmrest, disconnect the flex cable from the ZIF connector.
Palmrest Flex Cable and Bracket
7. Remove the two 4-mm screws securing the palmrest bracket.
8. While supporting the palmrest flex cable, lift out the palmrest bracket and turn it
over.
file:///F|/Service%20Manuals/Dell/Latitude/c800/ch2.htm (36 of 49) [2/28/2004 8:00:16 AM]
Removing and Replacing Parts : Dell Latitude C800/C805 Service Manual
9. Disconnect the reserve battery cable.
10. Remove the reserve battery:
a. Pry the reserve battery free from the metal palmrest bracket.
b. Remove the foam-pad remnants from the palmrest bracket.
Replacing the Reserve Battery
1. Seat the reserve battery and press it into place.
2. Connect the reserve battery cable.
3. Place the palmrest bracket loosely in the palmrest, and connect the palmrest flex
cable to the ZIF connector.
4. Replace the two 4-mm screws that secure the palmrest bracket to the palmrest.
System Board Assembly
NOTICE: Disconnect the computer and attached devices from electrical outlets and
remove any installed batteries.
NOTICE: To avoid ESD, ground yourself by using a wrist grounding strap or by
periodically touching unpainted metal on the computer.
System Board Screws
file:///F|/Service%20Manuals/Dell/Latitude/c800/ch2.htm (37 of 49) [2/28/2004 8:00:16 AM]
Removing and Replacing Parts : Dell Latitude C800/C805 Service Manual
The system board's BIOS chip contains the system service tag number, which is also
visible on a bar-code label on the bottom of the computer.
The replacement kit for the system board assembly includes a diskette or CD that provides
a utility for transferring the service tag number to the replacement system board
assembly.
NOTICE: If you received a flash BIOS update program diskette or CD with the
replacement microprocessor, you must update the BIOS after replacing the
microprocessor module. For instructions on updating or reflashing the BIOS, see the
Dell Portable Computer BIOS Update Guide.
Removing the System Board
file:///F|/Service%20Manuals/Dell/Latitude/c800/ch2.htm (38 of 49) [2/28/2004 8:00:16 AM]
Removing and Replacing Parts : Dell Latitude C800/C805 Service Manual
1. Follow the instructions in "Preparing to Work Inside the Computer."
2. Remove the hard drive and the fixed optical drive.
3. Remove any installed Mini PCI Cards.
4. If migrating the memory, remove all installed memory modules.
5. Remove the keyboard.
6. Remove the hinge cover.
7. Remove the display assembly.
8. Remove the palmrest assembly.
9. Remove the video graphics board.
10. Remove the microprocessor thermal cooling assembly.
11. If migrating the microprocessor, remove the microprocessor module.
12. Remove the three 4-mm captive-washer screws from the system board.
13. Remove the 20-mm screw from the center of the LED board.
14. Lift the front of the system board and work it out of the back panel.
System Board
file:///F|/Service%20Manuals/Dell/Latitude/c800/ch2.htm (39 of 49) [2/28/2004 8:00:16 AM]
Removing and Replacing Parts : Dell Latitude C800/C805 Service Manual
Battery and Modular Bay Latch Assemblies
NOTICE: Disconnect the computer and attached devices from electrical outlets and
remove any installed batteries.
NOTICE: To avoid ESD, ground yourself by using a wrist grounding strap or by
periodically touching unpainted metal on the computer.
Battery and Modular Bay Latch Assemblies
file:///F|/Service%20Manuals/Dell/Latitude/c800/ch2.htm (40 of 49) [2/28/2004 8:00:16 AM]
Removing and Replacing Parts : Dell Latitude C800/C805 Service Manual
Removing and Replacing the Battery and Modular
Bay Latch Assemblies
1. Follow the instructions in "Preparing to Work Inside the Computer."
2. Remove the keyboard.
3. Remove the hinge cover.
4. Remove the display assembly.
file:///F|/Service%20Manuals/Dell/Latitude/c800/ch2.htm (41 of 49) [2/28/2004 8:00:16 AM]
Removing and Replacing Parts : Dell Latitude C800/C805 Service Manual
5. Remove the palmrest assembly.
6. Remove a latch button from the bottom case assembly by squeezing the snap tabs in
the center of the latch.
Apply downward pressure to the tabs while squeezing them together (tweezers work
well) to eject the latch button from the bottom of the case without loosening the upper
latch assembly (spring and slider). If the upper latch assembly does come loose:
a. Reinsert the spring onto the slider, and reinstall both pieces in the latch
housing on the inside of the case.
b. Ensure that the slider is inserted so that the side with the two bumps is facing
the back of the case, and the surface with the wear ribs is facing the bottom of
the case.
7. Hold the upper latch assembly in place while you snap the new latch button in from
underneath the base, making certain the snap tabs are fully engaged in the slider.
8. Ensure that the newly installed latch assembly moves smoothly and freely when
pushed and released.
Battery Charger Board
NOTICE: Disconnect the computer and attached devices from electrical outlets and
remove any installed batteries.
NOTICE: To avoid ESD, ground yourself by using a wrist grounding strap or by
periodically touching unpainted metal on the computer.
Battery Charger Board
file:///F|/Service%20Manuals/Dell/Latitude/c800/ch2.htm (42 of 49) [2/28/2004 8:00:16 AM]
Removing and Replacing Parts : Dell Latitude C800/C805 Service Manual
Removing the Battery Charger Board
1. Follow the instructions in "Preparing to Work Inside the Computer."
2. Remove the keyboard.
3. Remove the hinge cover.
4. Remove the display assembly.
5. Remove the palmrest assembly.
6. Remove the video graphics board.
7. Lift the battery charger board out of the system board connector.
Replacing the Battery Charger Board
Align the screw holes on the battery charger board with the screw holes on the bottom
case assembly (see Battery Charger Board), and then press the battery charger board
file:///F|/Service%20Manuals/Dell/Latitude/c800/ch2.htm (43 of 49) [2/28/2004 8:00:16 AM]
Removing and Replacing Parts : Dell Latitude C800/C805 Service Manual
down into its connector.
LED Board
NOTICE: Disconnect the computer and attached devices from electrical outlets and
remove any installed batteries.
NOTICE: To avoid ESD, ground yourself by using a wrist grounding strap or by
periodically touching unpainted metal on the computer.
LED Board
file:///F|/Service%20Manuals/Dell/Latitude/c800/ch2.htm (44 of 49) [2/28/2004 8:00:16 AM]
Removing and Replacing Parts : Dell Latitude C800/C805 Service Manual
Removing the LED Board
1. Follow the instructions in "Preparing to Work Inside the Computer."
2. Remove the hinge cover.
3. Remove the two 4-mm screws.
4. Lift the LED board away from its connector.
Replacing the LED Board
1. Align the two screw holes with the two mounting holes on the bottom case assembly,
and press the board into its connector.
2. Replace the two 4-mm screws.
Fan Assembly
NOTICE: Disconnect the computer and attached devices from electrical outlets and
remove any installed batteries.
NOTICE: To avoid ESD, ground yourself by using a wrist grounding strap or by
periodically touching unpainted metal on the computer.
Fan Assembly
file:///F|/Service%20Manuals/Dell/Latitude/c800/ch2.htm (45 of 49) [2/28/2004 8:00:16 AM]
Removing and Replacing Parts : Dell Latitude C800/C805 Service Manual
Removing the Fan Assembly
1. Follow the instructions in "Preparing to Work Inside the Computer."
2. Remove the system board.
3. Remove the three 4-mm screws from the fan assembly.
4. Disconnect the two fan cables from the system board.
5. Pull the fan assembly away from the back-panel bracket.
NOTICE: When reconnecting the fan cables, connect the shorter cable to the
connector closest to the fan assembly. Route both cables so that they will not be
pinched by the thermal cooling assembly.
RJ-11/RJ-45 Board
file:///F|/Service%20Manuals/Dell/Latitude/c800/ch2.htm (46 of 49) [2/28/2004 8:00:16 AM]
Removing and Replacing Parts : Dell Latitude C800/C805 Service Manual
NOTICE: Disconnect the computer and attached devices from electrical outlets and
remove any installed batteries.
NOTICE: To avoid ESD, ground yourself by using a wrist grounding strap or by
periodically touching unpainted metal on the computer.
RJ-11 and RJ-45 Connector Covers
Removing the Protective Covers From the RJ-11 and
RJ-45 Connectors
Remove a plastic connector cover (if necessary) by slipping a nonmarring tool into the
cutout at the top and pivoting the tool up to disengage the inner securing tab.
To replace a connector cover, orient the cover notch-side-up and snap it into the connector
cutout.
RJ-11/RJ-45 Board
file:///F|/Service%20Manuals/Dell/Latitude/c800/ch2.htm (47 of 49) [2/28/2004 8:00:16 AM]
Removing and Replacing Parts : Dell Latitude C800/C805 Service Manual
Removing the RJ-11/RJ-45 Board
1. Follow the instructions in "Preparing to Work Inside the Computer."
2. Remove the system board.
3. Remove the 4-mm screw from the RJ-11/RJ-45 board.
NOTICE: The plastic tab is fragile; pull it back only far enough to remove the board
assembly.
4. Reach into the enclosure and, while pulling the tall plastic tab away from the board
assembly to release it, lift out the assembly.
When replacing the RJ-11/RJ-45 board assembly, protect the wiring harness by routing it
between the plastic posts.
RJ-11/RJ-45 Board Harness Routing
file:///F|/Service%20Manuals/Dell/Latitude/c800/ch2.htm (48 of 49) [2/28/2004 8:00:16 AM]
Removing and Replacing Parts : Dell Latitude C800/C805 Service Manual
Back to Contents Page
file:///F|/Service%20Manuals/Dell/Latitude/c800/ch2.htm (49 of 49) [2/28/2004 8:00:16 AM]