Text preview for : HP 5071A Manual Updating Changes.pdf part of Agilent HP 5071A Manual Updating Changes Agilent HP 5071A Manual Updating Changes.pdf
Back to : HP 5071A Manual Updating | Home
MANUAL UPDATING CHANGES CHANGE DATE: 20 September 2004
MANUAL UPDATING COVERAGE MANUAL IDENTIFICATION
Instrument: Agilent 5071A
This supplement adapts your manual Primary Frequency Standard
to Serial Numbers prefixed through: Operating and Programming Manual
US4433 Manual Print Date: December 2000
Manual Part Number: 05071-90041
ABOUT THIS SUPPLEMENT
The information in this supplement is provided to correct manual errors and to adapt the
manual to instruments containing changes after the manual print date.
Change and correction information in this supplement is itemized by page numbers
corresponding to the original manual pages. The pages in this supplement are organized in
numerical order by manual page number.
HOW TO USE THIS SUPPLEMENT
Insert this title page in front of the title page in your manual.
Perform all changes specified for "All Serials", and all changes through the Series Prefix
of your instrument or board.
Insert any complete replacement pages provided into your manual in the proper location.
The following pages are included in this update: [None]
sA
LIST OF EFFECTIVE PAGES
SERIAL PREFIX, SERIAL #
OR DATE CODE PAGES
If your manual has been updated according to the last edition of this supplement, you need
only perform those changes pertaining to the new series prefix; see List of Effective Pages.
New information affecting "All Serials" will be indicated by a "#" in front of the change.
All Serials 3-5, 4-23, 6-6, 6-7, and throughout manual
MANUAL CHANGES, AGILENT 5071A OPERATING AND PROGRAMMING MANUAL
SERIAL PREFIX, SERIAL #
OR DATE CODE CHANGES
US4345
Add new SCPI commands to page 5-36.
US4425
No manual changes
US4433
New start-up message, Page 1-6
#ALL SERIALS, Throughout the manual
> Option 300 removes the 6-character LED clock display, the
40-character x 2-line LCD display, and the input keypad. All
descriptions and references in this manual that describe
these features do not apply. Continuous Operation and
Attention LED indicators and one each of a 1 PPS output and
a Sync input, both BNC-style connectors, are still included
on the front panel. All communication with the 5071A is
handled via the RS-232 connector on the rear panel.
(05071-90041, December 2000)
LIST OF EFFECTIVE PAGES
SERIAL PREFIX, SERIAL #
OR DATE CODE PAGES
#ALL SERIALS, Throughout the manual (continued)
> Insert the following instructions at the end of Chapter 4.
Setting the Serial Port Parameters with the Option 300 Front
panel
This 5071A is shipped with a special program on CD-ROM. The
program "SER_SET.EXE" can be used to determine the current
serial port configuration and to change it to your specific
needs. When shipped from the factory a standard 5071a is set
to 2400,N,8,1. When the current serial port configuration is
known, it is also possible to change the configuration using
the SCPI commands described below.
Use the software in any PC with an RS-232 (COM) port
connected to the 5071A as described elsewhere in this
manual. The program can be run from the CD or copied to a
directory of your choice.
If you cannot locate the CD or need a copy of the program,
you can download it from our website at
http://agilent.com/find/frequencystandards
Click on 5071A and then click on Software. There is no
charge for this program. Alternatively you can contact your
local Agilent Sales Office via E-Mail or phone and request a
copy to be sent to you via E-Mail.
End of general Option 300 changes
(05071-90041, December 2000)
LIST OF EFFECTIVE PAGES
SERIAL PREFIX, SERIAL #
OR DATE CODE PAGES
#ALL SERIALS, Throughout the manual (continued)
> Option 046 removes the internal 45-minute standby
batteries. All references to battery charging, care,
removal, disposal, standby time, and disconnect switch do
not apply to this option.
> The yellow Attention LED will not flash to indicate
battery discharge.
> The status message "Power Source is BATT" will not appear
in the status log nor on the front panel LCD display.
End of general Option 046 changes
PREFIX US4433 and above, Page 1-6
> In the section headed: "Starting the 5071A"
> Change the following text:
The message "Waiting for ion pump start" may appear.
> Change it to:
The message "Waiting for Stabilization" may appear.
#ALL SERIALS, PAGE 3-5, Instrument States
>Change item 4. Warning to read:
4. Warning: The Yellow Attention light flashes while the Continuous Operation light
remains ON. This continues as long as the warning condition exists. The instrument
will return to Normal operation and the Attention light will stop flashing if the Warning
condition clears. A message describing the cause on the warning may be read from the
instrument's front panel via the LOG menu choice.
(05071-90041, December 2000)
LIST OF EFFECTIVE PAGES
SERIAL PREFIX, SERIAL #
OR DATE CODE PAGES
#ALL SERIALS, PAGE 4-23, Printer-Mode Output
>Change the Note to read:
These "unprompted" messages may be inconvenient when the instrument is controlled by
a computer and can be suppressed with the DIAG:LOG:VERB DISABLE command line.
The messages can then be obtained from the instrument's non-volatile log on demand.
PREFIX US4345 AND ABOVE, End of Chapter 5
> Add the following text and table of SCPI commands:
NOTE: Use care when typing the commands below. Once a serial port configuration is
altered it will be necessary to subsequently change your terminal emulator or modem
settings to match the new configuration for communication to continue.
COMMAND PARAMETERS COMMENTS
SYSTem:COMMunicate:SERial:BAUD Sets baud rate.
9600, 4800, 2400, 1200,
600, 300
SYSTem:COMMunicate:SERial:BITS Sets number of data bits.
7 or 8
SYSTem:COMMunicate:SERial:PARity Sets parity.
SYSTem:COMMunicate:SERial:SBITs Sets number of stop bits.
1 or 2
SYSTem:COMMunicate:SERial:BAUD? Returns baud rate.
SYSTem:COMMunicate:SERial:BITS? Returns number of data
bits.
SYSTem:COMMunicate:SERial:PARity Returns parity.
?
SYSTem:COMMunicate:SERial:SBITs? Returns number of stop
bits.
(05071-90041, December 2000)
LIST OF EFFECTIVE PAGES
SERIAL PREFIX, SERIAL #
OR DATE CODE PAGES
#ALL SERIALS, Page 6-6 Specifications
> Change warranty period for Option 001 High Performance CBT model 10891A to 5 years.
This applies to all 10891A sold since December 1, 2002, either as 10891A or as 5071A-001.
These units are identified by a 10891A serial number beginning with US4240 and higher.
#ALL SERIALS Page 6-6 After the Option 001 description, Add the following options and
descriptions:
Option 300: Blank Front Panel