Text preview for : 6100A_Manual.pdf part of Averatec 6100A Manual Averatec 6100A_Manual.pdf
Back to : 6100A_Manual.pdf | Home
6100A User's Manual
1
Notice
The information in this user's manual is subject to change without notice.
THE MANUFACTURER OR RESELLER SHALL NOT BE LIABLE FOR ERRORS
OR OMISSIONS CONTAINED IN THIS MANUAL AND SHALL NOT BE LIABLE
FOR ANY CONSEQUENTIAL DAMAGES, WHICH MAY RESULT FROM THE
PERFORMANCE OR USE OF THIS MANUAL.
The information in this user's manual is protected by copyright laws. No part of this
manual may be photocopied or reproduced in any form without prior written
authorization from the copyright owners.
Copyright December, 2004
All rights reserved.
Microsoft and Windows are registered trademarks of Microsoft Corporation.
Windows 95/98/ME/2000/NT/XP are trademarks of Microsoft Corporation.
Product names mentioned herein may be trademarks and/or registered trademarks
of their respective owners/companies.
The software described in this manual is delivered under a license agreement. The
software may be used or copied only in accordance with the terms of the agreement.
This product incorporates copyright protection technology that is protected by U.S.
patents and other intellectual property rights. Use of this copyright protection
technology must be authorized by Macrovision, and is intended for home and other
limited viewing uses only unless otherwise authorized by Macrovision. Reverse
engineering or disassembly is prohibited.
Rev 1.1
2
TABLE OF CONTENTS
PREFACE
Symbols and Conventions
Protecting Your Computer - Avoid Abusive Handling and Adverse
Environment
Chapter Summaries
1. GETTING TO KNOW THE BASICS
Performance Features
System at a Glance
Top View
Front and Rear Views
Side Views
Bottom View
AC Adapter
LED Status Indicators
Keyboard Features
Function (Quick) Keys
Windows Keys
Embedded Numeric Keypad
Touch Pad
Graphic Subsystem
Adjusting the Display Brightness
Extending the Life of the TFT Display Panel
Opening and Closing the Display Panel
Audio Subsystem
Adjusting the Volume in Windows
Voice Recording
Modem and Modem Setting
Ethernet Adapter
2. BIOS SETUP AND SECURITY
Entering the BIOS Setup Screen
Leaving the BIOS Setup Screen
BIOS Action Keys
3
Modifying the BIOS Settings
Main Setup
Advance Setup
Boot Setup
Security Setup
Power Setup
Exit Setup
3. BATTERY POWER & POWER MANAGEMENT
The Battery Pack
Lithium-Ion Battery Technology
Battery Low-Power Warning
Installing and Removing the Battery Pack
Charging the Battery and Charging Time
Checking the Battery Level
Prolonging the Battery's Life and Usage Cycles
Using Windows Power Options
Windows' Power Schemes
Suspend Modes
Power Button Action
Low Battery Warning
Power Manual Quick Access
4. UPGRADING YOUR COMPUTER
Upgrading the Hard Disk Drive
Upgrading the System Memory
5. TROUBLE-SHOOTING
First Step
Audio Problems
Hard Disk Problems
Optical Drive Problems
Display Problems
Keyboard and Mouse Problems
CMOS Battery Problems
Memory Problems
Modem Problems
4
Network Adapter / Ethernet Problems
PC Card / PCMCIA Problems
Performance Problems
FireWire (IEEE1394) and USB2.0 Problems
APPENDIX A Product Specification
APPENDIX B Agency Regulatory Notices
5
Preface
Using This Manual
This User's Manual contains general information about the
hardware and software setup, troubleshooting, and technical
specifications of the notebook computer.
Symbols and Conventions
The following conventions and symbols are used in this manual:
n When keys are to be pressed at the same time, a plus (+)
symbol is used. For instance, Fn+F7 means holding the Fn
and F7 keys at the same time.
n When a series of clicking actions is needed in Windows, [ ]
and > symbols are used. For instance, [Start > Settings >
Control Panel > Display] means clicking the Start icon first,
then the Settings, then the Control Panel, then the Display
icon.
n When you need to make a selection with the touch pad (or
mouse), you will be asked to 'select', `click', `double-click' or
`right-click' an item.
Note: Text in this format and symbol means specific instructions, commentary,
sidelights, or any additional information or notes that you should be aware of.
Warning: Text in this format and symbol means that failures to comply with the
given instructions or information could result in damage to your computer or bodily
harm or loss.
6
Protecting Your Computer - Avoid Abusive Handling and
Adverse Environment
Following the advice below will help ensure that you get the most
out of your Investment.
Your computer will serve you well if you take good care of it.
n Do not expose the computer to direct sunlight or place it near
sources of heat.
o o
n Do not subject it to temperatures below 0 C (32 F) or above
o o
30 C (86 F).
n Do not expose the computer to magnetic fields.
n Do not expose the computer to moisture or rain.
n Do not spill water or liquid on the computer.
n Do not subject the computer to adverse shock and vibration.
n Do not expose the computer to dust and dirt.
n Do not place objects on top of the computer to avoid damaging
the computer.
n Do not place the computer on rocky surfaces.
Here are some ways of taking care of your AC adapter.
n Do not connect the adapter to any devices other than your
computer.
n Do not let water get into the adapter.
n Do not block the ventilation airway of the adapter.
n Keep the adapter in a cool and ventilated place.
n Do not step on the power cord or place heavy objects on top of
it.
n Carefully tuck away the power cord and any cables away from
pedestrian traffic.
n When unplugging the power cord, do not pull on the cord itself
but pull on the plug.
7
n Keep the adapter away from children.
n The total ampere ratings of the equipment plugged in should
not exceed the ampere rating of the cord if you are using an
extension cord.
n The total current rating of all equipment plugged into a single
wall outlet should not exceed the fuse rating.
n Do not connect other AC adapter to your notebook. This
Notebook uses exclusively the AC adapter:
Manufacture: LI SHIN INTERNATIONAL ENTERPRISE CORP.
Model: PA-1650-01 (65W), PA1650-02 (65W); 0335C2065 (65W),
0335A2065 (65W)
When cleaning the computer, observe these steps:
1. Power off the computer and remove the battery pack.
2. Disconnect the AC adapter.
3. Use a soft cloth dampened with water. Do not use liquid or
aerosol cleaners.
Contact your dealer or see your service technician if any of the
following occurs:
n Computer has been dropped or the body has been damaged.
n Liquid has been spilled into the product.
n The computer does not operate normally.
Cleaning the Ventilation Grills:
It is suggested that you clean the ventilation grills regularly to
maintain optimal thermal regulation of the notebook. To do this, you
may use a soft brush or a vacuum cleaner (with appropriate head
adapter) to remove the dust buildup on the ventilation grills.
8
Chapter Summaries
The following is a summary of the available chapters and
appendices in this manual.
Chapter 1: Getting to Know the Basics
In this chapter, you will learn the basic operations and features
of your computer. It gives you a general understanding of the
components of your computer.
Chapter 2: BIOS Setup / Security
In this chapter, you will learn how to change various firmware
settings and what the settings mean. Also, you will learn how to
take advantage of the built-in security feature provided by the
BIOS.
Chapter 3: Battery Power & Power Management
In this chapter, you will learn the fundamentals of power
management and how to use them to achieve longer battery life.
Chapter 4: Upgrading Your Computer
In this chapter, you will learn how to upgrade the system
memory, the hard disk drive, and to install wireless mini PCI card.
Chapter 5: Trouble-Shooting
In this chapter, you will learn how to solve common hardware
and software problems.
Appendix A: Product Specification
In this section, you will find a list of the computer's system
specifications.
Appendix B: Agency Regulatory Notices
In this section, you will find the general electro-magnetic and
safety regulatory information.
9
C H A P T E R O N E
GETTING TO KNOW THE BASICS
This chapter introduces the features and
components of the computer.
10
Performance Features
n High Performance Processor
The notebook PC is equipped with the powerful Mobile
AMD Sempron processor which has advanced power
management features and high bus bandwidths
throughput.
n Advanced Graphic Engine
The Integrated Ultra256 video processor gives excellent
graphic performance. The advanced graphic chip also
incorporates a hardware-based motion-compensation
engine, which gives you smooth MPEG video playback. 3D
graphics capability also adds realism to PC games.
n LCD Display
The computer is equipped with a 15.4" WXGA TFT
high-resolution display panel for clear text and brilliant
colors.
n Expandability
The system offers upgradeable hard disk drive and 2 DDR
SDRAM sockets for expansion, allowing the user to easily
increase the storage and system capacities as the need
arises.
n Built-in Multiple Card Reader
The built-in 4-in-1 card reader supports the SD Card, MMC
Card, MS Card and MS-Pro Card portable media.
n Ethernet Port
The system provides built-in Ethernet network adapter for
high bandwidth network connection.
11
n FireWire (IEEE1394 / 1394a) and USB 2.0 ports
In addition to a full array of built-in I/O ports, the computer
offers IEEE1394 for ultra high-speed connection to high
bandwidth digital video devices and USB 2.0 ports for high
speed USB peripherals.
n Wireless LAN
The integrated Wireless LAN module allows your notebook
to connect wirelessly to other 802.11-enabled systems,
devices or network.
12
System At A Glance
Top View
1 2
3
11 10 9
4 7 4
5
6
7
1. LCD Latch
The LCD latches lock / unlock the LCD panel.
13
2. Built-in Microphone
The built-in microphone records sound.
3. LCD Display
The panel is where the visual output is displayed.
4. Built-in Stereo Speakers
The built-in speakers output the sound in stereo. In certain
models, the speakers are located in the lower section of the
display panel.
5. Keyboard
The keyboard is used to enter data. It has an embedded
numeric keypad and cursor control keys. (See Keyboard
Section for details.)
6. Touch Pad
The touch pad is a built-in pointing device with functions similar
to a mouse.
7. LED Status Indicator
The LED Status indicators reveal the status of these functions:
Numeric keypad, cap lock, scroll lock, WLAN module enabling
and disabling and also the ODD, HDD activities. (See the LED
Status Indicator Section for details.)
The LED Status indicators also reveal the status of the system
power state and battery-charging state. See the LED Status
Indicator Section for details.
8. Power / Suspend Button
The power/suspend button turns the notebook on and off and it
also acts as a system suspend key. Press momentarily to turn
on the system. Press and hold for at least 3~4 seconds to turn
14
off the system. How this key behaves can be defined in [Start >
Settings > Control Panel > Power Options > Advanced] menu.
Press the power / suspend button again to return from the
suspend mode. (See Chapter 3 for more details on system
suspend function.)
Note: When the system power is initially turned on, the Scroll-lock,
Cap-lock, and Numeric keypad LED indicators will light up momentarily to
indicate the start of the Power-On sequence.
9. Silent Mode Button
Pressing the key enables the system to lower its power usage;
therefore the fan speed is reduced and thus decreasing fan
noise.
You may need to go to BIOS Setup to enable Silent Mode for
this button. See Chapter 2 for details.
10. Email Launch Key
Pressing the button launches the Email application.
11. Internet Explorer Quick Key
Pressing the button launches Internet Explorer in Windows.
15
Front and Rear Views
1 2 3
4 5 6 7 8
Warning: Do not place any heavy objects on the top of notebook. This may
damage the display.
1. External VGA Port
The 15-pin VGA analog port is for connecting an external
monitor or projector.
2. Battery Pack
The battery pack is a built-in power source for the notebook.
3. Kensington Lock Key Hole
A Kensington-type security lock latches to this keyhole for
anti-theft purpose.
4. 4-in-1 Card Reader
The 4-in-1 Card Reader supports the SD Card, MMC Card, MS
Card and MS-Pro Card portable media.
5. Microphone Jack
The microphone jack (3.5-mm diameter) is where you connect
a microphone.
16
6. Audio Line-in Jack
The Audio Line-in jack (3.5-mm diameter) is where you connect
an external audio input source such as a CD Player.
7. Stereo Headphone / SPDIF-out Jack
The stereo headphone jack (3.5-mm diameter) is where you
connect the headphones or external speakers. Alternatively,
you may connect the SPDIF output to an external DTS, AC3, or
PCM sound processor / decoder in your home stereo system.
8. Wireless On/Off Switch
Use the Switch to disable or enable the integrated Wireless
function.
17
Side Views
1 2 3
6 7 8 9
4 5
Warning: Do not place any heavy objects on the top of notebook. This may
damage the display.
1. Ethernet / LAN Port
The port connects to a network hub via the RJ-45 cable and
also conforms to the 10/100Base-TX transmission protocol.
2. Modem Port
This is where you plug the phone jack (RJ-11) for fax/modem
functions.
3. Optical Drive and Disk Eject Button and Manual Eject Key
Hole
If your computer comes with a DVD+/-RW optical drive, you
may write data to a CD-R, CD-RW, DVD-R/RW and
DVD+R/RW media. Press the eject button to eject the disk tray.
The manual eject keyhole allows you to manually eject a
jammed disk.
18
4. PC Card Slot (Type II PCMCIA) and Card Eject Button
The slot is where you insert a Type II PC Card. Press the eject
button to release the PC Card.
Note: For safety consideration, please insert the PCMCIA dummy card when
not using the PCMCIA card.
5. Ventilation Grill
The fan grill is where air is exchanged to dissipate the internal
heat. Do not block this airway.
6. FireWire / IEEE1394 / 1394a Port
This is a high-speed data port. You may connect any FireWire
peripheral such as a digital video camera or external storage to
this port.
7. USB 2.0 Port (x3)
The Universal Serial Bus (USB 2.0-compliant) port allows you
to connect a wide variety of peripherals to your computer at a
rate of up to 480 Mbps. This port conforms to the latest USB
2.0 plug-and-play standards.
8. Power Jack (DC-in)
The DC-out jack of the AC Adapter connects here and powers
the computer.
9. TV (S-Video) Port
The S-Video port permits you to redirect the screen output to a
television set or any analog video playback device. This TV
Port is copyright protected; when DVD movie is played, the
output is scrambled to prevent analog recording.
19
Bottom View
1
5
4 2
3
1. Battery Pack and Battery Latch
The battery pack is a built-in power source for the notebook.
Slide the battery latch to release the battery pack.
2
1
20
2. USB Device Cover
Underneath the cover, there is a USB connector. This
connector is reserved for future use.
3. Hard Disk Drive Cover
The system's hard disk drive is located under the cover. The
HDD can be upgraded to a larger capacity. (See Chapter 4 for
instructions on upgrading the HDD.)
4. System Device Cover
The system's processor with cooling assembly, Wireless LAN
module, and DDR memory module are located under the case
cover. The system memory can be upgraded to a larger
capacity. (See Chapter 4 for instructions on upgrading the
memory.)
5. Ventilation Grill
The fan grill is where air is exchanged to dissipate the internal
heat. Do not block this airway.
Warning: Do not block the Fan Grill outlet. Place the machine on hard
surface only. The bottom case may get very hot without proper ventilation and
air circulation.
21
AC Adapter
1. DC-out Connector
The DC-out connector docks to the power jack (DC-in) on the
computer.
2. Adapter
The adapter converts alternating current into constant DC
voltage for the computer.
3. AC Plug
The AC plug plugs to the AC wall outlet.
Warning: Make sure you are using a standard 3-prong AC wall socket with a
ground pin. If not, you may feel a slight tingling sensation on any of the
computer's metal parts such as the I/O ports. This is caused by leakage current
when the AC adapter is not properly grounded (via the ground pin). However,
the amount of leakage current is within the safety regulation and is not harmful
to human body.
22
LED Status Indicator
The LED Status Indicator displays the operating status of your
notebook. When a certain function is enabled, an LED will light
up. The following section describes its indication.
System & Power Status Indicators
LED Graphic Indication
Symbol
Green light indicates the WLAN module
is active.
Blinking green light indicates the notebook
is in suspend mode.
Blinking orange light indicates the battery
is being charged.
Blinking red light indicates the battery
power is low when the system is turned
ON.
Persistent green light indicates the battery
is Full.
LED-off (Dark) indicates the system is
without battery.
Green light indicates the hard drive and/or
optical drive is being accessed.
Green light indicates the numeric keypad
is activated.
Green light indicates the cap-lock is
activated.
Green light indicates the scroll-lock is
activated.
Note: When the system power is initially turned on, the Scroll-lock, Cap-lock,
and Numeric keypad LED indicators will light up momentarily to indicate the
start of the Power-On sequence.
23
Keyboard Features
Function Keys (Quick Keys)
Graphic Action System Control
Symbol
Fn + F1 Enters Suspend Mode.
Fn + F3 Turns of the battery warning
beep off or on.
Fn + F4 Changes Display Mode:
LCD-only, CRT-only and
LCD&CRT.
Fn + F5 Turns Speaker Volume up.
Fn + F6 Turns Speaker Volume down.
Fn + F7 Increases Display Brightness.
Fn + F8 Decreases Display Brightness.
Fn+Num Lk Enables the embedded keypad
to work in numeric mode. The
keys act like numeric keypads
in a calculator. Use this mode
when you need to do a lot of
numeric data entry. An
alternative would be to connect
an external numeric keypad.
Fn+Scr Lk Press the Fn+Scr Lk key and
then press ? or ? to move one
line up or down.
For various system controls, press the Fn (Function) key and the Fx key
simultaneously.
24
Windows Keys
Your keyboard also has two Windows keys:
1. Start Key
This key allows you to pull up the Windows Start Menu at
the bottom of the taskbar.
2. Application Menu Key
This key brings up the popup menu for the application,
similar to a click of the right mouse button.
Embedded Numeric Keypad
Press Fn+Num Lk to enable the embedded numeric keypad.
The numbers are printed in upper right corner of a key, in a
color different from the alphabets. This key pad is complete
with arithmetic operators (+, -, * , /).
Press Fn+Num Lk to revert to normal character keys.
Num
Lk
7 8 9 *
4 5 6 -
1 2 3 +
Enter
0 . /
25
Touch Pad
The built-in touch pad, which is a PS/2-compatible pointing device,
senses movement on its surface. As you move your fingertip on the
surface of the pad, the cursor responds accordingly.
The following items teach you how to use the touch pad:
1. Move your finger across the touch pad to move the cursor.
2. Press buttons to select or execute functions. These two buttons
are similar to the left and right buttons on a mouse. Tapping on the
touch pad twice produces is similar to clicking the left button of a
mouse.
Function Left Button Right Equivalent Tapping Action
Button
Execution Click twice Tap twice (at the same speed as
quickly double-clicking
the mouse button)
Selection Click once Tap once
Drag Click and hold Tap twice quickly and on the
to drag the second tap hold finger to the touch
cursor pad to drag the cursor
Access Click once
Context Menu
Move One
Page Up or
Down
Tips on Using the Touch Pad:
1. The double-click speed is timed. If you double-click too slowly,
your notebook responds as if you single-clicked twice.
2. Keep your fingers dry and clean when using the touch pad.
Also keep the surface of touch pad clean and dry to prolong its life.
3. The touch pad is sensitive to finger movements. Hence, the
lighter the touch, the better the response. Heavy touch does not
produce better response.
26
Graphic Subsystem
Your computer uses a high performance 15.4" active matrix TFT
panel with high resolution and multi-million colors for comfortable
viewing. The integrated Ultra256 video graphics accelerator, which
is Microsoft DirectX 8.1 compatible, performs quick graphic
renderings.
Adjusting the Display Brightness
The notebook uses special key combinations, called hot keys,
to control brightness.
Press Fn+F7 to increase the brightness.
Press Fn+F8 to decrease the brightness.
Note: To maximize your battery operating time, set the brightness to the
lowest comfortable setting, so that the internal backlight uses less power. By
default, the LCD brightness will reduce to a lower setting when operating on
battery power. You may increase the LCD brightness manually by pressing
.
Extending the Life of the TFT Display Device
Observe the following guidelines to maximize the life of the
backlight in the display.
1. Set the brightness to the lowest comfortable setting
(Fn+F8).
2. When working at your desk, connect your notebook to an
external monitor and disable the internal display Fn+ F4.
3. Do not disable the suspend time-outs.
4. If you are using AC power and have no external monitor
attached, change to suspend mode when not in use.
27
Opening and Closing the Display Panel
To open the display, push the LCD latch inwardly and lift up the
lid. Then tilt it to a comfortable viewing position.
To close the display cover, fold it down gently until the LCD
latches click into place.
Warning: To avoid damaging the display, do not slam it when closing. Do not
place any object on top of the computer when the display is closed.
28
Audio Subsystem
Your computer's audio subsystem is Sound Blaster Pro-compatible.
Adjusting the Volume Manually
To increase the volume, press Fn+F5.
To decrease the volume, press Fn+F6.
Adjusting the Audio Volume in Windows
1. Click the speaker symbol in the task tray in Windows.
2. Drag the volume control bar up or down to adjust the volume.
3. To temporarily silence the speaker without changing the
volume setting, click Mute.
Voice Recording
A built-in microphone allows you to record sound. You will need
to use audio processing software to enable the built-in
microphone. For example, you may use Microsoft Sound
Recorder.
29
Modem
Your computer comes with a 56K V.92 internal fax/modem and a phone
jack (RJ-11), which is located on the left side of your computer.
Use a telephone cable to connect the computer to the telephone wall
outlet.
Connecting the Modem
1. Plug one end of the phone line into the modem port located on
the rear side of the computer. (For EMI compliance, you need to clip
the included EMI CORE to the phone line.)
2. Plug the other end of the line into the analog phone wall outlet.
Depending on where your computer is used, you may need to change
settings in the modem. Correct setting will allow you to maintain a stable
connection in a country where its telecommunication system may be
different to others.
To change the modem setting, do the following:
1. Go to [Start > Settings > Control Panel] and double-click on
Modem Settings icon. You will see a similar dialog box.
2. Click on the pull-down menu and select the country where it is
applicable. Click on OK to exit.
30
Ethernet
Your computer is equipped with a 10/100Base-TX Fast Ethernet
network adapter. Connect the active LAN cable to the RJ-45 LAN
port located on the left side of the computer. This allows you to
access and transmit data in the local area network.
Connecting to the Network
Use Unshielded Twisted Pair (UTP) Ethernet cable only.
1. Insert one end of the UTP cable into the network connector
until the connector snaps securely into the receptacle.
2. Either connect the other end of the cable to an RJ-45 jack
wall outlet or to an RJ-45 port on a UTP concentrator or hub in
the network.
Cabling Restriction for Networks
The following restrictions should be observed for 100BASE-TX
networks:
n The maximum cable run length is 100 meters(m) (328
feet[ft]).
n For 100-Mbps operations, use Category 5 wiring and
connections.
Note: Consult Help and Support from the Start Menu for additional network
configuration instructions.
31
C H A P T E R T W O
BIOS SETUP AND SECURITY FEATURE
In this chapter, you will learn how to
enter the BIOS Setup Menu and
manipulate various hardware control
settings. You will also learn how to use
the built-in security features.
32
The Setup Utility is a hardware configuration program built into
your computer's BIOS (Basic Input/Output System). It runs and
maintains a variety of hardware functions. It is a menu-driven
software, which allows you to easily configure and change the
settings.
The BIOS contains manufacture's default settings for the
computer's standard operations. However, there are occasions
when you may be required to modify the default settings in the
BIOS. For example, you may need to configure the BIOS power
management (APM) settings if you are using DOS, or
non-Windows operating system.
The BIOS allows you to set up passwords to limit access to users.
This is an important feature because a great deal of vital
information is carried within the computer nowadays. Unauthorized
access can be prevented. Later in this chapter, you will learn how to
use this security feature.
33
Entering the BIOS Setup Screen
First turn on the power. When the BIOS performs the POST
(Power-On Self Test), press F2 key quickly to activate the AMI
BIOS Setup Utility.
Note: You may need to press F2 key fairly quickly. Once the system begins to load
Windows, you may have to retry by cycle-power on again
Leaving the BIOS Setup Screen
When you have finished modifying the BIOS settings, exit the BIOS.
It takes a few seconds to record changes in the CMOS.
BIOS Action Keys
Function Key Command Description
Leaves a sub-menu to return to the
ESC Exit previous menu OR exits the BIOS setup
while saving changes.
Enter Go to Sub Screen Shows the Sub Menu
F1 General Help Shows the Help Screen
Saves changes and reboots the
F10 Save and Exit
computer.
Select a field Selects the next field.
? Select an item Selects the next upper item.
? Select an item Selects the next lower item.
- Lower value Selects the next value within a field.
+ Higher value Selects the next value within a field.
34
Modifying the BIOS Settings
The AMIBIOS setup main menu is subdivided into sub-menus.
Each menu item is described in this section.
Main Setup
Under this menu, you may change time/date and view basic
processor and system memory information.
Item Selections / Description
Sub-menu
Date N/A Type in the current date, in MM/DD/YY
format.
Time N/A Type in the current date, in HH:MM:SS
format.
Advanced Setup
? IDE Configuration
Item Selections / Description
Sub-menu
Primary Hard Disk Primary Master is where BIOS tries to
IDE boot from first. The primary master
Master controls the hard drive.
Secondary ATAPI CDROM The secondary master controls the
IDE ATAPI CD-ROM drive.
Master
Note: The sub-menu is not selectable. Press enter to view information of the
35
storage device.
Item Selections / Description
Sub-menu
Touch Pad Enabled Enable or disable the built-in touchpad.
Support Disabled
Share 32MB You may choose the amount of system
Memory 64MB memory to be used as video frame
128MB buffer.
LCD Auto Enabled [Enabled]: The LCD backlight
Dim Disabled automatically decreases when
Function operating on battery power.
[Disabled]: This function is disabled.
Boot Setup
? Boot Settings Configuration
Item Selections / Description
Sub-menu
Quick Disabled [Enabled]: The system skips certain tests
Boot Enabled while booting. This shortens the boot-up
time.
[Disabled]: The system performs full tests
while booting.
Quiet Boot Disabled When Enabled, the system will display
Enabled the AVERATEC logo instead of the
POST messages.
When Disabled, the system will display
POST messages (i.e. devices
information.)
Bootup Off [On]: The numeric keypad on the
Num-Lock On keyboard is enabled on boot.
36
? Boot Device Priority
Item Selections / Description
Sub-menu
1st Boot Removable Dev. Set the type of device for the 1st drive
Device Intel UNDI, PXE-2 BIOS attempts to boot from. If Intel UNDI,
Hard Drive PXE-2 is selected, system will attempt to
CD/DVD load boot sector from the Ethernet port.
2nd Boot Set the type of device for the 2nd drive
Device BIOS attempts to boot from.
Note: If you select Intel UNDI, PXE-2, the system will attempt to boot from the
network.
Note: When the BIOS performs POST, you may also press F12 Key to enable the
Boot Device selection menu. You may choose CD/DVD, Hard Drive, or Intel UNDI,
PXE-2 as the first storage device to boot from. If you have already connected a USB
Floppy Disk Drive before powering up, it will appear as a Removable Device in the
Boot Device selection menu
37
Security Setup
? Boot Settings Configuration
Item Selections / Description
Sub-menu
Change N/A Install or Change the Password
Supervisor
Password
Change N/A Install or Change the Password
User
Password
Clear User N/A Install or Change the Password
Password
Boot Disabled To enable or disable the boot sector
Sector Enabled protection.
Virus When Enabled, BIOS gives a warning
Protection when any program attempts to rewrite
or delete the boot sector.
Note: About Boot Sector Virus Protection:
If enabled, the following warning message appears when a program attempts to alter
the boot sector. You may have to enter "N" several times to prevent the boot sector
write.
Boot Sector Write!!!
Possible VIRUS: Continue (Y/N)? _
The following warning message appears when a program attempts to format the
hard disk drive.
Format!!!
Possible VIRUS: Continue (Y/N)? _
Using Password Protection
Two Levels of Password Protection are available. The BIOS
provides both a Supervisor and a User password. If you try to
activate both passwords, the Supervisor password must be set first.
38
The passwords activate two different levels of protection:
1. System always asks for password every time it is powered on.
2. System asks for password only when you attempt to enter
BIOS utility.
The passwords are encrypted and stored in NVRAM. Make sure
you write them down or memorize them. If you lost the passwords,
the computer may need to be sent back to the factory or to an
authorized service dealer to reset the passwords.
39
Power Setup
Item Selections / Description
Sub-menu
Power Button On/Off [On/Off]: When the power button is
Mode pressed, the system is turned off.
Suspend
[Suspend]: When the power button is
pressed, the system enters the suspend
mode.
Silent Mode Enabled When Enabled, cooler fan speed is
Button reduced. The processor performance is
Disabled also reduced.
Note: The Suspend Mode selection in BIOS only applies to older Windows version
(such as Windows 3.1 or Windows 95 or NT4) or non-Windows operating system. In
Windows ME / 98SE / 2000 / XP, suspend mode and settings are determined by
settings in the Power Options Properties (Start > Control Panel > Power Options).
40
Exit Setup
Item Selections / Description
Sub-menu
Saves N/A After you have completed the BIOS
Changes and settings, select this item to save all
Exit settings, exit BIOS Setup utility, and
reboot. New system settings will take
effect on next power-up. F10 key can be
used for this operation.
Discard N/A Discards changes done so far to any of
Changes and the setup questions and exit.
Exit
Load Optimal N/A Load Optimal Default value for all the
Defaults setup questions. F9 key can be used for
this operation.
41
C H A P T E R T H R E E
BATTERY POWER & POWER
MANAGEMENT
In this chapter, you will learn the
fundamentals of power management
and how to use it to achieve longer
battery life.
42
In this chapter, you will learn how to operate your notebook on
battery power, how to handle and maintain the battery pack, and
learn about the system's power saving features.
The LCD, processor and hard disk drive are the major hardware
subsystems that consume the most power. Power management
deals how these key components should behave to conserve power.
For example, you can have the system turn off its display after 2
minutes of inactivity to save power. Efficient power management
can help you work longer sessions before having to recharge the
battery.
The Battery Pack
Lithium-Ion Battery
Your notebook uses a six-cell Lithium-Ion battery pack
that provides power when you don't have access to an
AC outlet.
Note: It is necessary that you charge the battery pack for at least 6
hours before using it for the first time.
Note: In the Standby Suspend mode, a fully charged battery loses its
power in roughly 1/2 day or less. When not being used, the battery's
power will deplete in 1-2 month.
43
Battery Low-Power Warning
1. Low Battery Warning
Low battery condition occurs when battery power is
reduced to 6%. The red battery status LED indicator
blinks and the system beeps once every 16 seconds or
so.
2. Very Low Battery Warning
Very Low battery condition occurs at 3 % power
remaining. The red battery status LED indicator blinks
and the system beeps at 4-second interval.
When the notebook warns you of its low battery condition,
you will have about 3-5 minutes to save your current
work.
Warning: Do not expose battery packs to temperatures below 0
degree Celsius (32 degree F) or above 60 degree C (140F). This may
adversely affect the battery pack.
Note: Press Fn+F3 to turn off the battery warning beep.
44
Installing and Removing the Battery Pack
To Remove the Battery Pack:
1. Place the notebook bottom-side up on a flat and
secured surface.
2. Push the latch and pull the battery's hard case
away from the notebook.
2
1
45
To Install the Battery Pack:
1. Place the notebook bottom-side up on a flat and
secured surface.
2. Carefully insert the battery pack into the battery
compartment of the notebook.
Charging the Battery and Charging Time
To charge the battery, while the battery pack is in the notebook,
plug the AC adapter into the notebook and an electrical outlet.
The charging time is approximately 4-6 hours when the
notebook is turned off and approximately 8-12 hours when the
notebook is turned on.
When the battery is fully charged, the battery charge indicator
becomes green light (on).
Note: If system runs at heavy loading or in a high temperature environment,
the battery may not be fully charged. You need to continue to charge it with the
AC adapter plugged in until the charging LED turns off.
46
Checking the Battery Level
You can check the remaining battery power in the Windows
battery status indicator, which is located at the lower right-hand
corner of the task bar. (If you do not see a battery or AC-in icon
on the task tray, go to Power Options Properties box and click
on the Advanced tab. Check off ``Always show icon on the task
bar``.)
Alternatively, you can access the power meter by clicking the
Power Options icon in the Windows Control Panel.
Prolonging the Battery's Life and Usage Cycles
Below are suggestions you can follow to prolong the use of
battery.
n Use the AC adapter wherever AC wall outlet is available.
This will ensure uninterrupted computing.
n Purchasing an additional battery pack.
n Store the battery pack in room temperature. Higher
temperature tends to deplete the battery's power faster.
n Make good use of the power management function. Save
To Disk (Hibernate) saves the most energy by storing current
system contents in a hard disk space reserved for this function.
n The life expectancy of the battery is approximately 300
recharges.
n See the notices section in the beginning of the user
manual on how to care for the battery pack.
Note: Read Section Protecting Your Notebook in the beginning of this manual
for tips about how to maintain the battery pack.
Note: To achieve optimal battery performance, you may need to do a battery
calibration at a 3-month interval. To do this:
1. Fully charge the battery.
2. Then discharge the battery by entering the BIOS setup screen. (Press F2
key as soon as you turn on the computer. And let it remain at the setup screen
until the battery runs out.
3. Fully charge the battery again.
47
Using Windows Power Options
Windows Power Management provides basic power saving
features. In the Windows Power Options Properties [Start >
Settings > Control Panel > Power Options] dialogue box, you
may enter time-out values for display and hard disk drive.
Windows power manager saves power by turning off hard drive
after 1 minute of inactivity, for example.
Windows' Power Schemes
The power management control panel in Windows XP,
known as Power Schemes, is designed to provide the
user with an easy-to-use interface. The Power Schemes
tab can be found in the Power Options Properties panel
that is accessible via the control panel window.
Schemes are easy to understand, based on notebook
usage scenarios, and control not only processor power
usage but other system peripherals as well.
Go to [Start > Settings > Control Panel] and double-click
the Power Options icon.
Always on mode puts the processor into maximum
performance mode, which provides no power saving.
The other schemes control processor performance
based on demand. For example, Max Battery mode
lowers the processor's speed and voltage to conserve
power as much as possible.
48
In this dialog box, you can manually set the LCD and
hard drive's time-out values in the Plugged in column and
in the Running on batteries column. Lower time-out
values will save more battery power.
Note: Also consult Windows user guide for more information on how
to use Windows power management functions.
Note: Actual dialogue box shown above may appear slightly different.
49
Suspend Mode
Standby Suspend
The system automatically enters this mode after a period
of inactivity, which is set in the Power Schemes dialog
box. In Standby mode, hardware devices, such as
display panel and hard disk, are turned off to conserve
energy.
Hibernate Suspend
In this mode, all system data are saved in the hard disk
before powering down. When this mode is activated, all
system state and contents are saved to the hard disk
drive after a period of inactivity defined by the user. No
power or very little power is drawn from the battery
module under this mode.
However, depending on how much RAM that have been
installed on your computer, the amount of time the
system requires to restore all its previous contents can
range from 5 to 20 seconds.
For Windows 2000 / XP users, hibernation is handled by
the operating system; therefore, no special disk partition
or disk file is necessary.
If you wish to activate Hibernate mode, you need enable
Hibernate Support in the Hibernate tab of the Power
Options menu.
50
Note: Do not install, remove or change the memory module when the
system is in the suspend or hibernate mode.
Note: Actual dialogue box shown above may appear slightly different.
51
Power Button Action
The notebook PC's power button can be set to turn off
the system or activate the suspend mode.
Go to [Start > Settings > Control Panel > Power Options]
and click on the Advanced tab. In the pull-down menu,
select how you wish the power button to work as.
Note: Actual dialogue box shown above may appear slightly different.
Warning: In the When I close the lid of my portable computer
pull-down menu, DO NOT select Do nothing