Text preview for : Samsung_PN59D8000FFXZA_fast_track_guide_[SM].pdf part of Samsung Samsung PN59D8000FFXZA fast track guide [SM] Samsung Monitor Samsung_PN59D8000FFXZA_fast_track_guide_[SM].pdf
Back to : Samsung_PN59D8000FFXZA_fa | Home
PN59D8000FFXZA Fast Track Troubleshooting Manual, Rev. 1/11/12
Y Buffer X Buffer Service Bulletins
X Main Plasma Screen Peeling Issue -
ASC20110708001
SMPS Related Model Code(s): PN59D7000FFXZA /
Y Main PN59D8000FFXZA / PN64D8000FFXZA
Please check GSPN for parts update!
Quick Parts List:
Version Parts No Short Description
Main ALL BN44-00447A Power PCB
ALL BN94-04402U Main PCB
I101 BN96-16531A Logic Main PCB
Logic ALL BN96-16532A Buffer E
ALL BN96-16533A Buffer F
ALL BN96-16534A Buffer G
ALL BN96-16535A X Main
ALL BN96-16536A Y Main
Spkr
Spkr Wi-Fi ALL BN96-16537A Buffer X
Blue Tooth
ALL BN96-16538A Buffer Y Up
Buffer E Buffer F
ALL BN96-16539A Buffer Y Down
ALL BN96-17107A RF module PCB
HELP: 1-888-751-4086 (Tech Support) Latest Firmware: Please check I101 BN96-18260E Function & IR PCB
1-866-894-0637 (FE) Samsung.com for latest update! Y504 BN96-20516A Logic Main PCB
Y503 BN96-20516A Logic Main PCB
Firmware for PDP TV D8000 series (ver.
I101 BN96-18201A Panel
GSPN 1022.1)
Y503 BN96-20269A Panel
http://gspn3.samsungcsportal.com Description:
Y504 BN96-20270A Panel
This firmware will: -Decrease flickering
ALL BN63-07791A Bottom Cover
problem on 3D mode. (only 3D model)
PLUS ONE ALL BN96-16787A Stand Base
- Change the way to get out of Store Demo
http://my.plus1solutions.net/clientPortals/samsung ALL BN96-16814A Front Cover
Mode
ALL BN96-16826B Rear Cover
- Change the type of information of Info banner
HOT TIPS - Prevent escaping issue when pressing
ALL BN96-16829A Stand Guide
I101 BN59-01134A Remote
-Power On Problems: (pg. 3) volume button on video apps(Netflix, Vudu,
ALL BN59-01134B Remote
-Video Problems: (pg. 4) etc)
ALL BN96-18070B Speaker
- Support Remote Service
ALL BN96-18130H LVDS Cable
- Support Netflix 3.1
ALL BN96-09872R Power Cord
PN59D8000FFXZA Fast Track Troubleshooting Manual
Power On Sequence:
1. STBY 5V (CN801, #2, 5v)
2. PS_ON (CN801, #1, 3.3v-0v)
3. VS_ ON (CN802, #6, 0-3.3v)
4. Panel should illuminate briefly
PN59D8000FFXZA Fast Track Troubleshooting Manual
Sample
"VITAL SIGNS"
When troubleshooting, It's very important to first check Vs, Va, Vsc & Ve
If Vs is missing (0V), disconnect power and check for short. Use ohm
Power Supply Trouble Shooting Notes: meter to measure resistance while disconnecting Y-Board & X-Board
supply feeds one at a time.
2010/2011 models
Turn Power On and Test SMPS with shorted connector removed for
Will not be run with the "X" or "Y" main disconnected. The SMPS will correct Vs voltage verification. (It may only come up briefly but to full
shut down immediately. However if a meter is first connected to the level). Be careful not to reconnect power connectors until Vs falls below
test point when power is applied it will read the correct voltage briefly 10V.
before shut- ting down.(You have enough time to check key
If Va is low or missing, disconnect power connectors to Address Boards
voltages)
and Check to see if SMPS Supply is restored. (Note Va feed normally
CAUTION: Do not reconnect any connectors to SMPS or Y/X Boards passes through the Y-Drive to the Address Boards (Logic Buffer Boards).
until power has been turned off long enough for Vs to drop below 10V If Vsc is low or missing and Vs is OK, the failure is with the Y-Board
or damage will occur to X or Y Boards. .
since the Y-Board generates the Vsc voltage from the supplied Vs.
SMPS Over Current Protection If Ve is low or missing and Vs is OK, the failure is with the X-Board since the
Ve is generated by the X-Board from the supplied Vs. (Please note: In some
If a short circuit occurs on either the VS or VA voltage lines, the SMPS rare cases the Ve is generated by the Y-Board fed to the X-Board.)
stops operating, but should not fail. When the short circuit is removed
from the source line, the Power Supply will operate normally again. Other SMPS Voltages:
Many SMPS Supplies are replaced needlessly! Check Low Voltage feeds to the Main Board and other supplied Assemblies.
3
PN59D8000FFXZA Fast Track Troubleshooting Manual
TROUBLESHOOTING VIDEO PROBLEMS
1. Verify Video Operation 2. Using Test Patterns in Service Mode
a) Customer Picture Test (if available) - ENTERING SERVICE MODE