Text preview for : hfe_denon_dn-s5000_service_en.pdf part of DENON hfe denon dn-s5000 service en DENON CD DN-S5000 hfe_denon_dn-s5000_service_en.pdf
Back to : hfe_denon_dn-s5000_servic | Home
For U.S.A., Canada &
Europe model
SERVICE MANUAL
MODEL DN-S5000
TABLE TOP SINGLE CD PLAYER
Some illustrations using in this service manual are slightly different from the actual set .
16-11, YUSHIMA 3-CHOME, BUNKYOU-KU,TOKYO 113-0034 JAPAN
Telephone: 03 (3837) 5321
X0161V.02 MO/CDM 0302
DN-S5000 2
DISASSEMBLY
(Follow the procedure below in reverse order when reassembling)
1. SLIP DISC, SLIP MAT
(1) Remove a screw 69 and pull out Slip Disc and Slip Mat.
.
Washer
69
Slip Disc
Slip Mat
Slip Sheet
Anti-static Sheet
2. PLATTER
(1) Remove Belt from Motor Pully.
(2) Remove 3 screws 60 and pull out Platter.
.
60 60
Platter
Belt
Motor Pully
2
DN-S5000 3
3. DRIVE UNIT
(1) Remove 4 screws 71 and pull out Drive Unit.
(2) Disconnect Flat cable and Connector.
(3) Detach Drive Unit.
.
Drive Unit
71
71
Connector
Flat cable
Drive Unit
Note:
Do not pull out aslant to prevent Flat cable damage.
Do not fail to pull AC cord from wall outlet before disconnect the Flat cable and Connector.
If AC cord is remained plugged into wall outlet, power is kept supplied in the unit, which may cause danger.
4. COVER UNIT
(1) Remove 5 screws 70 and pull out Cover Unit.
(2) Disconnect Connectors.
(3) Detach Cover unit.
.
Cover unit 70
CX042 70
Connector CX101
CX041
70
Connector
CX031
Note:
Do not fail to pull AC cord from wall outlet before disconnect Connectors.
If AC cord is remained plugged into wall outlet, power is kept supplied in the unit, which may cause danger.
3
DN-S5000 4
5. SENSOR AND SCALE UNITS OF PLATTER
(1) Remove 2 screws 64 and pull out Sensor Cover and Sensor unit.
(2) Remove a E Ring.
(3) Pull out Scale unit.
64
64
E Ring
Sensor Cover
Scale unit
Sensor unit
6. SENSOR AND SCALE UNITS OF SLIP DISC
(1) Remove 2 screws 64 and pull out Sensor Cover and Sensor unit.
(2) Remove a screw 60 and pull out Scale unit.
.
Scale unit 64 64
60 Sensor Cover
Sensor unit
7. POWER PWB
(1) Remove 5 screw 51 and pull out Power PWB.
.
51
Power PWB
51
4
DN-S5000 5
8. DSP PWB UNIT
(1) Remove 9 screws 52 and pull out DSP PWB unit
.
52
DSP PWB unit
52
52
9. DRIVE COVER
(1) Remove 4 screws 12 and pull out Drive cover.
.
19
Drive cover
19
19
19
10. DRIVE
(1) Move Drive Rack in arrow direction through the Hole on the bottom chassis.
Loader frame comes out.
(2) Pull up Loader panel while pulling it towards front.
(3) Remove 4 screws 6 and pull out Drive.
.
Drive
4
6
6 4
5
DN-S5000 6
BLOCK DIAGRAM
1 2 3 4 5 6 7 8
DN-S5000
-HB,F1,F2
GND,+5,+9 A
33M LEDdriver
128Mb D16 ~ 31 BU2090
SDRAM TFS0 LRCK main out
TCK0 BCLK AMP10
ROM ADRESS ADSP21065L TXD0A MAIN1 8CH PANEL
DRIVE TXD0B MON1 D/A mon out