Text preview for : 526Xsvc.pdf part of DAEWOO 526X 526X schematics
Back to : DAEWOO 526X.rar | Home
Service Manual
XGA COLOR MONITOR Model : 526X
DAEWOO ELECTRONICS CO., LTD.
http : //svc.dwe.co.kr
CONTENTS
SAFETY PRECAUTIONS GENERAL SAFETY INFORMATION SERVICING PRECAUTIONS TECHNICAL INFORMATION GENERAL INFORMATION PIN CONNECTOR CAUTIONS FOR ADJUSTMENT AND REPAIR OPERATION AND ADJUSTMENT ALIGNMENT PROCEDURE TROUBLESHOOTING HINTS BLOCK DIAGRAM PCB LAYOUT SCHEMATIC DIAGRAM EXPLODED VIEW DIAGRAM 1 2 3 6 7 8 8 9 12 15 29 30 32 33 34 35
INFORMATION OF PART DESCRIPTION ELECTRICAL PARTS LIST
SAFETY PRECAUTIONS
CAUTION: No modifications of any circuits should be attempted. Service work should be performed only after you are thoroughly familiar with all of the following safety checks and servicing guidelines.
x Safety Check
Care should be taken while servicing this analog color display because of the high voltages used in the deflection circuits. These voltages are exposed in such areas as the associated flyback and yoke circuits.
x Fire & Shock Hazard
· Insert an isolation transformer between the analog color display and AC power line before servicing the chassis. · When servicing, pay close attention to the original lead dress especially in the high voltage circuit area; if a short circuit is found, replace all parts which have been overheated as a result of the short circuit. · All the protective devices must be reinstalled per original design. · Soldering must be inspected for possible cold solder points, frayed leads, damaged insulation, solder splashes or sharp solder points. Be certain to remove all foreign materials.
x Implosion Protection
Picture tube in this monitor employs integral implosion protection system, but care should be taken to avoid damage and scratching during installation. Only use same type replacement picture tubes. IMPORTANT SAFETY NOTICE: There are special components used in this analog color display, which are important for safety. These parts are shaded on the schematic diagram and on the replacement parts list. It is essential that these critical parts should be replaced with manufacturer's specified parts to prevent X-Ray, shock, fire or other hazards. Do not modify the original design without getting written permission from DAEWOO ELECTRONICS CO. or this will void the original parts and labor warranty.
x X-Ray
WARNING: The only potential source of X-Ray is the picture tube. However when the high voltage circuitry is operating properly, there is no possibility of an X-Ray problem. The basic precaution which must be exercised is to keep the high voltage at the following factory recommended level. NOTE: It is important to use an accurate, periodically, calibrated high voltage meter. · To measure the high voltage, use a high-impedance high-voltage meter. Connect(-) to chassis and (+) to the CRT anode button. · Turn the Contrast & Brightness Control fully counterclockwise. · Measure the high voltage. The high voltage meter should indicate the following factory recommended levels. · If the upper meter indication exceeds the maximum level, immediate service is required to prevent the possibility of premature component failure. · To prevent X-Ray possibility, it is essential to use the specified picture tube. · The normal high voltage is 25.5KV or below and must not exceed 29KV at zero beam current at rated voltage.
1
GENERAL SAFETY INFORMATION
x Terms in the manual
CAUTION Statements identify conditions or practices that could result in damage to the equipment or other property. WARNING Statements identify conditions or practices that could result in personal injury or loss of life.
x Terms as marked on equipment
Statements indicate a personal injury hazard not immediately accessible as one reads the marking or a hazard which is properly included on the equipment itself. WARNING Statements are clearly concerning indicated personal injury hazards. CAUTION
x Symbols in the manual
The symbols indicate where applicable cautionary or other information is to be found.
x Symbols as marked on equipment
Protective GROUND terminal
x High Voltage Warning
And Critical Component Warning Label
The following warning label is on the CRT PWB shield case inside the unit. Warning: This product includes critical mechanical and electrical parts which are essential for x ray protection. For continued safety, replace critical components that are indicated in the service manual with exact replacement parts given in the parts list. Operating high voltage with this product is 29Kv at minimum brightness. Refer to service manual for measurement procedures and proper service adjustments.
2
SERVICING PRECAUTIONS
CAUTION: Before servicing instruments covered by this service manual, its supplements, and addendum, please read and follow the SAFETY PRECAUTIONS of this manual.
NOTE: If unforeseen circumstances create conflict between the following servicing precautions and any of the safety precautions on page 1 of this manual, always follow the safety precautions. Remember: Safety First.
x General Servicing Precautions
1. Always unplug the AC power cord from the AC power source before: a. Removing or reinstalling any component, circuit board, module, or any other instrument assembly. b. Disconnecting or reconnecting any electrical plug or other electrical connection. c. Connecting a test substitute in parallel with an electrolytic capacitor in the instrument. CAUTION: A wrong part substitution or incorrect polarity installation of electrolytic capacitors may result in a explosion. d. Discharging the picture tube anode. 2. Test high voltage only by measuring it with an appropriate high voltage meter or other voltage measuring device (DVM, FETVOM. etc.) equipped with a suitable high voltage probe. Do not test high voltage by "drawing an arc". 3. Discharge the picture tube anode only by: (a) first connecting one end of an insulated clip lead to the degaussing or line grounding system shield at the point where the picture tube socket ground lead is connected, and then (b) touching the other end of the insulated clip lead to the picture tube anode button, using an insulating handle to avoid personal contact with high voltage. 4. Do not any spray chemicals on or near this instrument, or any of its assemblies. 5. Unless otherwise specified in this service manual, only clean electrical contacts by applying the following mixture to the contacts with a pipe cleaner, cotton-tipped stick, or comparable nonabrasive applicator: 10% (by volume) Aceton and 90% (by volume) isopropyl alchohol (90%-99% strength). CAUTION: This is a flammable mixture. Unless specified in this service manual, lubrication of contacts is not required. 6. Do not damage any plug/socket B+ voltage interlocks with which instruments covered by this service manual might be equipped. 7. Do not apply AC power to this instrument and/or any other of its electrical assemblies unless all the solid-state device heat sinks are correctly installed. 8. Always connect the test instrument ground lead to the appropriate instrument chassis ground before connecting the test instrument positive lead. Always remove the test instrument ground lead last. 9. Only use the test fixtures specified in this service manual with this instrument. CAUTION: Do not connect the test fixture ground strap to any heatsink in this instrument.
3
x Electrostatically Sensitive (ES) Devices
Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components are commonly called Electrostatically Sensitive (ES) Devices. The typical examples of ES devices are integrated circuits, some field-effect transistors, and semiconductor "chip" components. The following techniques should be used to help reduce the incidence of component damage caused by static electricity. 1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, wipe off any electrostatic charge on your body by touching any known earth ground. Alternatively, obtain and wear a commercially available discharging wrist strap device which should be removed for potential shock reasons prior to applying power to the unit under testing conditions. 2. After removing the electrical assembly equipped with ES devices, place the assembly on a conductive surface such as aluminum foil to prevent electrostatic charge buildup or exposure to the assembly. 3. Only use a grounded-tip soldering iron to solder or unsolder ES devices. 4. Only use an anti-static type solder removal device. Some solder removal devices not classified as "antistatic" can generate enough electrical charges to damage ES devices. 5. Do not use freon-propelled chemicals. These can generate enough electrical charges to damage ES devices. 6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil, or comparable conductive material). 7. Immediately before removing the protective material from the leads of replacement ES devices, touch the protective material to the chassis or circuit assembly into which the device will be installed. CAUTION: Be sure that no power is applied to the chassis or circuit, and observe all other safety precautions. 8. Minimize bodily movements when handling unpackaged replacement ES devices. (Otherwise harmful motion such as the brushing together clothes fabric or the lifting your foot from a carpeted floor can generate enough static electricity to damage ES devices).
x General Soldering Guidelines
1. Use a grounded-tip, low-wattage soldering iron with appropriate tip size and shape that will maintain tip temperature between a 550°F-660°F (288°C-316°C) range. 2. Use an appropriate gauge of RMA resin-core solder composed of 60 parts tin/40 parts lead. 3. Keep the soldering iron tip clean. 4. Throughly clean the surface to be soldered. Use a small wire-bristle (0.5 inch or 1.25cm) brush with a metal handle. Do not use freon-propelled spray-on cleaners. 5. Use the following soldering technique: a. Allow the soldering iron tip to reach normal temperature (550°F to 660°F or 288°C to 316°C) b. Hold the soldering iron tip and solder strand against the component lead until the solder melts. c. Quickly move the soldering iron tip to the junction of the component lead and the printed circuit foil, and hold it there until the solder flows onto and around both the component lead and the foil. d. Closely inspect the solder area and remove any excess or splashed solder with a small wire-bristle brush. CAUTION: Work quickly to avoid overheating the circuit board printed foil.
4
FIGURE 1. USE SOLDERING IRON TO PRY LEADS
x IC Removal/Replacement
Some utilized chassis circuit boards have slotted (oblong) holes through which the IC leads are inserted and then bent flat against the circuit foil. When holes are slotted, the following technique should be used to remove and replace the IC. When working with boards using the familiar round hole, use the standard technique as outlined in paragraphs 5 on the page under the title of general soldering guidelines.
x Removal
1. Desolder and straighten each IC lead in one operation by gently prying up on the lead with the soldering iron tip as the solder melts. 2. Draw away the melted solder with an anti-static suction-type solder removal device (or with desoldering braid before removing the IC.
x Replacement
1. Carefully insert the replacement IC in the circuit board. 2. Carefully bend each IC lead against the circuit foil pad and solder it. 3. Clean the soldered areas with a small wire-bristle brush. (lt is not necessary to reapply acrylic coating to the area).
x "Small-Signal" Discrete Transistor Removal/Replacement
1. Remove the defective transistor by clipping its leads as close as possible to the component body. 2. Bend the ends of each of three leads remaining on the circuit board into a "U" shape. 3. Bend the replacement transistor leads into a "U" shape. 4. Connect the replacement transistor leads to the corresponding leads extending from the circuit board and crimp the "U" with long nose pliers to ensure metal-to-metal contact, then solder each connection.
5
x Power IC, Transistor or Devices Removal/Replacement
1. Heat and remove all solders from the device leads. 2. Remove the heatsink mounting screw (if applicable). 3. Carefully remove the device from the circuit board. 4. Insert new device in circuit board. 5. Solder each device lead and then clip off excess lead. 6. Replace heatsink.
x Diode Removal/Replacement
1. Remove defective diode by clipping its leads as close as possible to diode body. 2. Bend the two remaining leads perpendicularly to the circuit board. 3. Observing diode polarity, wrap each lead out of the new diode around the corresponding lead on the circuit board. 4. Securely crimp each connection and solder it. 5. Inspect the solder joints of the two "original" leads on the circuit board copper side. If they are not shiny, reheat them and apply additional solder if necessary.
TECHNICAL INFORMATION
CDT Size Diagonal visible image area Dot Pitch Synchronization Horizontal Vertical Plug and Play Power Saving Power Source Power Consumption Dimension-W x H x D (set with stand) Weight-unpacked(lbs/Kg) Operating Temperature
15-inch 14-inch 0.28 mm 30 - 54 KHz 50 - 160 Hz DDC1/2B/CI EPA, VESA DPMS, Nutek Compliant 100-240 Vac, 50/60Hz (Free Voltage) 70W 360 x 381 x 389mm
25.1/11.4 10 ~ 40°C /50 ~ 104°F
6
GENERAL INFORMATION
This color monitor automatically scans all horizontal frequencies from 30KHz to 54KHz, and all vertical frequencies from 50Hz to 160Hz. This color monitor supports IBM PC, PC/XT, PC/AT, personal System/2 (PS/2), Apple Macintosh, and compatible users crisp text and vivid color graphics display when using the following graphics adapters : (VGA, 8514/A, Super VGA, VESA and XGA and Apple Macintosh Video Card). And so, this color monitor has a maximum horizontal resolution of 1024 dots and a maximum vertical resolution of 768 lines for superior clarity of display. By accepting analog signal inputs which level is zero to 0.7 Volts. This color monitor can display and unlimited palette of colors depending on the graphics adapter and software being used.
x Abbreviations
ADJ AFC CRT Def D.Y FBT H.SYNC OSC P.S.U PWA R.G.B V.Sync Adjustment Automatic Frequency Control Cathode Ray Tube Deflection Deflection Yoke Flyback Transformer Horizontal Synchronization Oscillator Power Supply Unit Printed Circuit Board Wiring Assembly Red, Green, Blue Vertical Synchronization
7
PIN CONNECTOR
Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Signal Red Green Blue GND GND GND - Red GND - Green GND - Blue +5Vdc GND - H.Sync GND - V.Sync Bi-directional Data (SDA) Horizontal Sync Vertical Sync (VCLK) Data Clock (SCL)
1
6 15
10
Arrangement of 15-pin D-sub connector
CAUTIONS FOR ADJUSTMENT AND REPAIR
· Degaussing is always required when adjusting purity or convergence. · The white balance adjustment has been done by a color analyzer in factroy. The adjustment procedure, described in the service manual is made by a visual check. · Allow 20 minutes warm-up time for the display before checking or adjusting only electrical specification or function. · Reform the leadwire after any repair work.
x Caution For Servicing
· In case of servicing or replacing CRT, high voltage sometimes remains in the anode of the CRT. Completely discharge high voltage before servicing or replacing CRT to prevent a shock to the serviceman.
8
OPERATION AND ADJUSTMENT
Control Panel
SELECT ADJUST MENU
MENU
·
SELECT
Launch OSD(On-Screen Display) MENU window.
· · · · · · ·
Select a sub Menu & function. Move a sub Menu & function. Increase the value of any selected function. Adjust the contrast directly when there is no OSD. Move a sub Menu & function. Decrease the value of any selected function. Adjust the brightness directly when there is no OSD.
9
Key Process
MENU
SELECT
MENU
MENU
MENU
OSD OFF
·
When you choose the icon
on the OSD window, you can exit the OSD screen.
10
OSD Functions
ICON CONTROL FUNCTIONS
H. POSITION
Adjust the position of the display horizontally (left or right).
V. POSITION
Adjust the position of the display vertically (up or down).
H.SIZE
Adjust the display width (horizontal size).
V.SIZE
Adjust the display height (vertical size).
V. LINEARITY
Adjust the vertical linearity.
PINCUSHION
Adjust the left and right margins for more convex or more concave margins.
TRAPEZOID
Adjust the trapezoid of the screen by moving the lines inward or outward.
PIN BALANCE
Adjust the side balance when the sides of the screen are bowed towards left or right.
PARALLELOGRAM Adjust the parallelogram when the screen is leaning left or right.
T. PIN CORNER Adjust the pin corner top when the top sides of the screen are bowed.
B. PIN CORNER Adjust the pin corner bottom when the bottom sides of the screen are bowed.
T. PIN BALANCE
Adjust the side pin corner balance top when the top sides of the screen are bowed towards left or right.
B. PIN BALANCE
Adjust the side pin corner balance bottom when the bottom sides of the screen are bowed towards left or right.
COLOR TEMP
Choose different preset color temperatures or set your own customized color parameters.
11
ICON
CONTROL
FUNCTIONS
RED GAIN
Adjust the red gain.
GREEN GAIN
Adjust the green gain.
BLUE GAIN
Adjust the blue gain.
RED BIAS
Adjust the red bias.
GREEN BIAS
Adjust the green bias.
BLUE BIAS
Adjust the blue bias.
LANGUAGE
Select language for OSD (5 languages).
DEGAUSS
Degaussing keeps the monitor free from unwanted magnetism that can result in color impurity.
STATUS
Display horizontal & vertical frequency and polarity.
H. MOIRE
Adjust the horizontal picture moire cancellation.
V. MOIRE
Adjust the vertical picture moire cancellation.
RECALL
Reset the screen to the Factory Preset Display Settings.
ROTATION
Adjust the rotation when the screen is tilted left or right (Optional).
12
ALIGNMENT PROCEDURE
x Standard Adjustment Conditions
1. Power source voltage : 100-240Vac 50/60Hz 2. Aging : Take at least 20 minutes warm-up time. 3. Signals Video : Analog 0.7Vpp 75 terminal positive polarity Synchronizing : TTL level Negative/Positive Separate Deflection frequency Horizontal Frequency : 30KHz - 54KHz Vertical Frequency : 50Hz - 160Hz
x Pre-Adjustment
1. B+ Adjustment Adjust 6.15Vdc ± 0.05Vdc between P503 and ground at 31.5KHz mode, varying VR001. Adjust -150Vdc ± 0.5Vdc between P504 and ground at 31.5KHz mode, varying VR501.
x Method to launch the factory mode
Step 1. Push the menu button. Step 2. Push the menu button and plus control button ( + ) for 5 times in same time.
x Main Adjustment
1. Setting the Controls Set the value of items as following. Contrast : Max.(OSD value up to MAX) Brightness : Center(Set the OSD value to center) 2. H.size, V.size, H.phase, V.position, Pincushion, Trapezoid Receive the cross hatch pattern of Factory preset mode. H.size, V.size, H.phase, V.position, Pincushion, Trapezoid are adjusted at each mode. In Factory, Auto Alignment was done at each mode. Therefore, Factory preset mode has it's own value according to each control. 3. Focus (a) Set brightness control to center and contrast control to MAX. (b) Receive all "H" character pattern of 1024 X 768 (48KHz, 60Hz) (c) Adjust the Focus control of FBT to obtain best Focus. 4. Geometric Distortion Adjustment. (a) Receive the cross hatch pattern of factory preset mode. (b) Pincushion, Trapezoid are adjusted the best geometric status. 5. White Balance Adjustment (a) Select 9300°K on the OSD Menu. (b) Receive a full white pattern of 54KHz mode signal by using the signal generator. (c) Set the brightness control to the maximum, the contrast control to the maximum. (d) Cut off the FBT screen VR. (e) Receive all the black patterns. The luminance of the screen should be 0.5~1.0 Ft-L by using Screen VR. (f) Select the R-BIAS, G-BIAS and B-BIAS on the control menu and adjust the +/ key to get the color coordinates in x=0.281 ± 0.015, y=0.311± 0.015. (g) Receive a full white pattern. Adjust the brightness value to the center. (h) Select the R-GAIN and B-GAIN and adjust the +/ key to get the color coordinates in x=0.281 ± 0.015, y=0.311 ± 0.015. (i) Adjust the ABL control to get the screen luminance to 30 Ft/L (a full white pattern over 30 Ft/L) (j) Check if the x, y coordinates of color analyzer is in x=0.281±0.015, y=0.311±0.015. If the color coordinates is out of range, adjust the R. G. B BIAS & GAIN to get the coorinates in x=0.281, y=0.311. Make sure that the coordinates is in range. (k) Select 6550°K on the OSD Menu and set the color coordinates in x=0.313, y=0.329 at the maximum contrast control and center brightness control (l) Check if a full white pattern is over 30Ft/L.
13
6. Static Convergence Adjustment (a) Apply a magenta cross hatch pattern on display. (b) Adjust the focus from the best over all focus on the display. Also adjust the brightness to the desired condition. (c) Vertical red and blue lines are converged by varying the angle between the two tabs of the 4-pole magnets. (d) Horizontal red and blue lines are converged by varying the tabs together, keeping the angle between them constant. (e) Apply a yellow cross hatch pattern on display. (f) Vertical green and red lines are converged by barying the angle between the two tabs of the 6-pole magnets. (g) Horizontal green and red lines are converged by varying the tabs together, keeping the angle between them constant.
14
TROUBLESHOOTING HINTS
1. No Character
No Character
Are the Contrast & Brightness Controls in OSD menu maximum? Yes
No
Change the Contrast & Brightness control value to maximum
Is whole screen bright? Yes
No
No Raster
Refer to No Raster
Is CRT Cathode (Rk, Gk, Bk) signal level normal? No Is the output signal of the (pin 21,24,26) pre-amp IC801, normal?
Yes Rk, Gk, Bk About 30~35Vpp
Check the peripheral circuit of CRT
Yes
Check the video output circuit and its ambient circuit
No No
Is 12V line normal? Yes Is clamping pulse (pin 18 of IC801) normal? Yes
Trouble in 12V line of the Main PWB
No 5Vp-p
Check the clamping pulse circuit
Is input signal normal? Yes Trouble in IC801 and its ambient circuit
No
Check the signal cable
15
2. No Raster
No Raster
Is CRT heater red-hot? Yes Turn the Brightness & Contrast control to set Maximum Yes
No
Is Heater Voltage (CRT PWB) about 6V? No Trouble in power supply circuit
Yes
Trouble in CRT
Refer to trouble in power supply unit.
Is whole screen bright?
No
Trouble in power supply circuit
Yes Check G1 voltage about -40V? Yes Is CRT G2 (screen) voltage about 500V? Yes Is 100Vdc line normal? Trouble in 100Vdc line of power supply unit Refer to trouble in P.S.U
No
Trouble in G1 line
No
Trouble in FBT or its pin 4 ambient circuit
No
Yes Does the Brightness control make screen bright? Yes Trouble in FBT
No
High Voltage trouble in FBT
16
3. A Missing Color
One color is missing
Is input signal normal? 0.7Vpp Yes Is the output of pre-amp (IC801, KA2500) pin 21, 24, 26 all normal? Yes
No
Check video signal cable or video card.
No
Trouble in IC801 or its ambient circuit
CRT Cathode (Rk, Gk, Bk) is normal? Yes
No RK, GK, BK About 40V p-p
Is video output IC802 waveform normal? Yes
No
Trouble in video output circuit, IC802 or ambient
Each grid (G1, G2) voltage normal? Yes No Replace CRT
Trouble in 100Vdc line
Trouble in G1,G2 line
17
4. Abnormal OSD Font
Abnormal OSD Font
* If menu key selected.
Is menu key selected? Is OSD Font exist? Yes One color is missing Yes Is the output of IC803 (pin 12,13, 14) normal?
No
Is Heater Voltage about 6V?
No
Trouble in Heater voltage line. Refer to trouble in P.S.U
Yes Troubie in IC803 or its ambient circuit
No
Trouble in IC803 and its ambient circuit
Yes
Refer to Missing Color
18
5. Horizontal Output Circuit
MODE VGA Super VGA 54KHz B+ Voltage 72Vdc 86Vdc 124Vdc Trouble in Horizontal output circuit (No Raster)
Is the B+line voltage over 175V? Yes
No
Trouble in 175V line.
11V 0V
Is the H-out waveform of IC501 normal? Yes
No
Trouble in IC501
10V 0V
Is the Gate wave form of Q553 normal? Yes
No
Trouble in Q551, Q552
Is the Drain waveform of Q553 normal? 66V Yes Trouble in Q554 and its ambient circuit.
No
Trouble in Q553
19
6. Unstable Picture 6-1. Horizontal
Unstable picture
Is H.Sync input pin of IC501 correct?
No
Check H.Sync Out of Micom or its ambient circuits.
Yes
Trouble in IC501
20
6-2. Vertical
Unstable picture
Is the 12V,-12Vdc line voltage is correct?
No
Refer to P. S. U
Yes
40V
-10V
50Vp-p
Is the pulse of pin 5 of the IC401 correct?
Yes
Trouble in vertical D. Y
No
Is the output of pin 4 of IC501 all normal?
Yes
Check IC401 and its ambient circuit
No Check the IC501 and its ambient circuit
21
7. Focus
Monitor remains unfocused
Check Focus VR in FBT
Is focus acceptable?
Yes
OK
No Trouble in Focus circuit (FBT)
22
8. Convergence
Poor convergence
Is convergence on the center area bad?
Yes
Adjust static convergence Refer to Adjustment procedure of convergence
No
Is convergence on the fringe area bad?
Yes
Adjust D.Y Location
23
9. Abnormal Picture 9-1. Horizontal Size
* At first, adjust controls in the OSD Menu
Abnormal H.Size
Is the DC level of the base of Q509 changeable?
No
Is the DC level of IC501 pin 5 changeable ?
Yes
Check IC501 pin 5
Yes Is the collector pulse of Q554 correct?
=1100Vp-p
Yes Is the cathode waveform of D568 correct? Yes Trouble in H.OSC/ Deflection Circuit
No
Trouble in Horizontal output circuit Check the B+ and anode voltage of CRT.
* Normally anode voltage of CRT is approximately, 24KV
80-310Vpp
No
Trouble in L835, C543 or their ambient circuit
* Scan B+ are as follow : MODE VGA Super VGA 54KHz B+ Voltage 72Vdc 86Vdc 124Vdc
Refer to Horizontal Output circuit
24
9-2. Vertical Size
Abnormal V.Size
Is changeable the DC voltage of IC401 pin 1?
No
Is the 3.5Vdc of pin 4 of the IC501?
Yes
Check the IC4 and its ambient circuit
Yes
No
Trouble V.OSC/ Deflection Circuit Refer to V.OSC/Deflection circuit
Check the IC501 and its ambient circuit
25
10. Side-Pincushion Circuit
Side-Pincusion distortion is excessive or barrel
Select the side-pincushion icon on OSD menu, and adjust acceptable position.
Yes
O.K
No
Is the pin 5 waveform of IC501 correct No Trouble in IC501
Yes
Check IC501 or their ambient circuit (pin 13, 14)
26
11. Power Supply Unit (P.S.U)
Trouble in P.S.U
Is power switch on? Yes Is fuse F001 O.K? Yes Is the IC001 O.K? Yes Is voltage of D002 130V (270V)? Yes Is the waveform of T001 pin5 correct? Yes Is voltage of C101 100Vdc? Yes Is voltage of C104 50Vdc?
No
Switch on
No
Check the power cord outlet and diode D001,D002,D003,D004
No
Replace IC001
No
Trouble in diode D001,D002,D003,D004 or peripheral device
No
Trouble in switching power transformer T001 or IC001 and its ambient circuit
No
Trouble in T001 or D101
No
Trouble in T001 or D102
A
27
A
Is voltage of C117 14.3Vdc?
No
Trouble in D103 or horizontal Part.
Yes Is voltage of C643 -15Vdc? Yes Is voltage of C112 25Vdc? No Trouble in D105 No
Trouble in D643 or vertical Part.
Yes P.S.U O.K
28
BLOCK DIAGRAM
MAIN BLOCK DIAGRAM
RECEPTACLE
(02WE4E1)
VIDEO BLOCK DIAGRAM
VIDEO PREAMP
(KA2500)
15PIN D-SUB
SCL SDA
R,G,B
CRT
VIDEO OUTPUT AMP
(TDA9532) R,G,B BIAS BRIGHT CONTROL
EPROM
( 24LC08)
OSD IC DEGAUSSING CIRCUIT
DEGAUSS CONTROL CLAMP&BLANKING PULSE (KS2508) H.SYN V.SYNC
SCREEN & FOCUS
ROTATION
(OPTION) HIGH VOLTAGE
HCS SCL SDA DPMS CONT.
ABL ADJUST
MCU
(KS88C6224)
V.SYNC H.SYNC
H.OSC & V.DRV
(1888CT)
SMPS CONTROL
(KA3842)
H.DRV
V.DRV AMP (TDA8172)
G1
CONTROL
H.DRV
SYNC SMPS TRANSFORMER TRANS
(DST-603) SYNC. TRIGGERING
H.DY
BUCK TRANS H.CS BLOCK
SCAN B+ H.SIZE FB FBP
H.SIZE & G/D C0NTROL.
H. LIN COIL
G1 MUTE
OUTPUT REGULATOR
+12V,+5V
B+ CONTROL
(uPC1555C)
V. DY
X-RAY PROTECT VIDEO POWER
80V 12V, 5V
H/V CONTROL
(KA7500)
F/B
MAIN POWER
100V, 12V 50V, -12V 5V, 6.3V
HV.DRV
B+ BUCK L.
FBT
POWER TACT S/W
LED
TACT
S/W
BUTTON
(4 BUTTON)
29
SCHEMATIC DIAGRAM
32
EXPLODED VIEW DIAGRAM
33
INFORMATION OF PART DESCRIPTION
Important Safety Notice
Components identified with the International Symbol have special characteristics important for safety. When replacing any components, use only manufacturer's specified parts.
Abbreviation of Description
RESISTOR Description Allowance F ± 1% J ± 5% K ± 10% M ± 20% G ± 2% Example: Fig & Index R101 R102 Part No Description
Resistors RD-4Z820J Carbon: 82J RD-4Z201J Carbon1/4W-200J
CAPACITOR Description C D F J K P Z Allowance ± 0.25pF ± 0.5% ± 1pF ± 5% ± 10% ± 100% ~ 0% ± 80% ~
Example: Fig & Index C102 C402 C105 Part No Description
Capacitors CCXF1H104Z Ceramic 50V 0.1µ F Z CCXB1H331K Ceramic 50V 330PF K CMXM 2A224J MYLAR 100V 0.22µ F J
34
ELECTRICAL PARTS LIST
The components identified by mark ! have special characteristics important for safety and x-ray radiation. These should be replaced only with the types specified in the parts list.
LOC
PART-CODE
PART-NAME PCB MAIN COIL BEAD COIL BEAD COIL BEAD COIL BEAD COIL BEAD COIL BEAD COIL BEAD COIL BEAD COIL BEAD COIL BEAD
PART-DESC T=1.6*246*310 SP502B+IS14 3ASL/100 BI-4865(5TS) BI3890 BI3890 BI3890 BI3857(AXIAL) BFD 3512 R2 BI3857(AXIAL) BI3857(AXIAL) BI3857(AXIAL) BI3857(AXIAL) BI3857(AXIAL) WORLDAC250V0.1UFMR.47 2.5KV 2200PF M AC250V 400V SMH 220MF (25.4*40) HIKE 2KV 0.01MF P 25V RSS 100MF (6.3X11) TP 50V HIKF 0.1MF Z MEU 100V 0.33MF J 100V 3300PF J (TP) 100V 0.1MF J (TP) 50V B 1500PF K (TAPPING) 1KV B 270PF K (TAPPING) 100V 2200PF J (TP) 50V B 1000PF K 160V RSS 47MF (13X25) TP HIKF 500V 0.01MF Z 1KV B 470PF K (T) 63V RSS 220MF (10X20) TP 1KV B 220PF K (TAPPING) 25V RSS 470MF (10X16) TP 16V RSS 100MF (6.3X11) TP 16VRSS 1000MF (10X20) TP 16VRSS 1000MF (10X20) TP 16V RSS 470MF (10X12.5)TP 63V RSS 220MF (10X20) TP HIKE 2KV 0.01MF P 50V B 180PF K AXIAL 16V RSS 100MF (6.3X11) TP 50V CH 22PF J (TAPPING) 50V CH 22PF J (TAPPING) 50V RSS 0.1MF (5X11) TP
LOC
PART-CODE
PART-NAME
PART-DESC 50V RSS 4.7MF (5X11) TP 50V HIKF 0.1MF Z 50V B 1000PF K 50V HIKF 0.1MF Z 50V B 680PF K 50V B 680PF K 50V B 680PF K 50V B 680PF K 50V HIKF 0.1MF Z 50V HIKF 0.1MF Z 50V B 180PF K AXIAL 50V B 180PF K AXIAL 500VB1000PFK(TAPPING) 50V B 270PF K (TAPPING) 100V 5600PF J (TP) MEU 250V 0.1MF J 100V 0.027MF J (TP) 100V MEU 0.22MF J 16VRSS1000MF(10X20)TP 50V HIKF 0.1MF Z 100V MEU 0.22MF J 35V RSS 100MF (8X11.5) TP 50V HIKF 0.1MF Z 100V 0.033MF J (TP) 50V RSS 33MF (6.3X11) TP 50V HIKF 0.1MF Z MEU 63V 1MF J 50V RSS 10MF (5X11) TP 50V B 1000PF K 100V 2200PF J (TP) 50V HIKF 0.1MF Z 16V RSS 330MF (8X11.5) TP 50V RSS 1MF (5X11) TP 50V RSS 10MF (5X11) TP 50V B 1000PF K 50V SL 390PF J 50V B 1000PF K (TAPPING) 50V RSS 1MF (5X11) TP 50V B 100PF K 50V RSS 10MF (5X11) TP 50V B 180PF K AXIAL 50V B 180PF K AXIAL 50V F 0.01MF Z 16V RSS 330MF (8X11.5) TP 16V RSS 47MF (5X11) TP 1KV B 100PF K
00001 9979800516
C206 CEXF1H479V C ELECTRO C207 CCZF1H104Z C CERA C208 CCZB1H102K C CERA C209 CCZF1H104Z C CERA C210 CCZB1H681K C CERA C211 CCZB1H681K C CERA C212 CCZB1H681K C CERA C213 CCZB1H681K C CERA C214 CCZF1H104Z C CERA C215 CCZF1H104Z C CERA C231 CCZB1H181K C CERA C232 CCZB1H181K C CERA C301 CCXB2H102K C CERA (C1) C401 CCXB1H271K C CERA C402 CMXM2A562J C MYLAR C404 CMXL2E104J C MYLAR C405 CMXM2A273J C MYLAR C406 CMXL2A224J C MYLAR C407 CEXF1C102V C ELECTRO C408 CCZF1H104Z C CERA C409 CMXL2A224J C MYLAR C410 CEXF1V101V C ELECTRO C411 CCZF1H104Z C CERA C501 CMXM2A333J C MYLAR C502 CEXF1H330V C ELECTRO C503 CCZF1H104Z C CERA C504 CMXL1J105J C MYLAR C505 CEXF1H100V C ELECTRO C506 CCZB1H102K C CERA C507 CMXM2A222J C MYLAR C508 CCZF1H104Z C CERA C509 CEXF1C331V C ELECTRO C510 CEXF1H109V C ELECTRO C511 CEXF1H100V C ELECTRO C512 CCZB1H102K C CERA C513 CXSL1H391J C CERA C514 CCXB1H102K C CERA C515 CEXF1H109V C ELECTRO C516 CCZB1H101K C CERA C517 CEXF1H100V C ELECTRO C518 CCZB1H181K C CERA C519 CCZB1H181K C CERA C520 CCZF1H103Z C CERA C521 CEXF1C331V C ELECTRO C522 CEXF1C470V C ELECTRO C531 CCXB3A101K C CERA
00020 WNA75N031- CORD POWER
! B001 5PB14865-! B003 5PB13890-! B004 5PB13890-(J004)
! B005 5PB13890-(J003) B101 5PB13857-B301 5PB13857-(B1) B501 5PB13857-B502 5PB13857-B809 5PB13857-B810 5PB13857--
B102 5MBFD3512R COIL BEAD
! C001 CL1UC3104M C LINE ACROSS ! C004 CH1FDF222M C CERA AC
C005 CEYP2G221Z C ELECTRO C006 CCXE3D103P C CERA C007 CEXF1E101V C ELECTRO C008 CCZF1H104Z C CERA C009 CMXL2A334J C MYLAR C010 CMXM2A332J C MYLAR C011 CMXM2A104J C MYLAR C012 CCXB1H152K C CERA C013 CCXB3A271K C CERA C014 CMXM2A222J C MYLAR C015 CCZB1H102K C CERA C101 CEXF2C470V C ELECTRO C102 CCXF2H103Z C CERA C103 CCXB3A471K C CERA C104 CEXF1J221V C ELECTRO C105 CCXB3A221K C CERA C106 CEXF1E471V C ELECTRO C107 CEXF1C101V C ELECTRO C108 CEXF1C102V C ELECTRO C109 CEXF1C102V C ELECTRO C110 CEXF1C471V C ELECTRO C111 CEXF1J221V C ELECTRO C302 CCXE3D103P C CERA (C2) C201 CCZB1H181K C CERA C202 CEXF1C101V C ELECTRO C203 CXCH1H220J C CERA C204 CXCH1H220J C CERA C205 CEXF1H108V C ELECTRO
35
LOC
PART-CODE
PART-NAME
PART-DESC MPA 400V 0.47MF J 100V 0.022MF J TP 200V MPP 0.62MF J MPP 200V 0.22MF J 50V RSS 1MF (5X11) TP 100V 3300PF J (TP) MEU 63V 1MF J 50V RSS 10MF (5X11) TP 50V RSS 0.47MF (5X11) TP 250V RSS 10MF (10X20) TP
LOC
PART-CODE
PART-NAME
PART-DESC 50V B 390PF K 50V F 0.01MF Z (TAPPING) 16V RSS 100MF (6.3X11) TP HIKF 500V 0.01MF Z SMH250+51088+20379#28=250 M36KXU110XX61(T) 0.12*6*16+BL101NG*2=580 PCS629-03A SMW250-08 5267-06A STICK TYPE 5267-07A STICK TYPE 2A05 2A05 2A05 2A05 D2L20U HER107 1N4148 AUTO 52MM 1N4148 AUTO 52MM RU 1P (TAPPING) RG4 D2L20U D2L20U 1N4148 AUTO 52MM D2L20U 1N4148 AUTO 52MM 1N4148 AUTO 52MM 1N4148 AUTO 52MM 1N4148 AUTO 52MM 1N4148 AUTO 52MM 1N4148 AUTO 52MM 1N4002 1N4148 AUTO 52MM 1NS4 1N4148 AUTO 52MM 1A5G DTV32F 1N4937GP (TAPPING) 1A5G 1N4148 AUTO 52MM RG4 ER206 ER206 1A5G 1N4148 AUTO 52MM 1N4148 AUTO 52MM 1N4148 AUTO 52MM 1N4148 AUTO 52MM 1N4148 AUTO 52MM 1N4148 AUTO 52MM 1N4148 AUTO 52MM
C535 CMXA2G474J C MYLAR C536 CMXM2A223J C MYLAR C537 CMYF2D624J C MYLAR C538 CMXF2D224J C MYLAR C540 CEXF1H109V C ELECTRO C541 CEXF1C101V C ELECTRO C542 CMXM2A332J C MYLAR C543 CMXL1J105J C MYLAR C545 CEXF1H100V C ELECTRO C546 CEXF1H478V C ELECTRO C547 CEXF2E100V C ELECTRO C548 CMXM2A223J C MYLAR C550 CMXM2A104J C MYLAR C551 CEXF2A100V C ELECTRO C552 CMXM2A104J C MYLAR C553 CCXB2H102K C CERA C554 CEXF1H220V C ELECTRO C555 CMXM2A393J C MYLAR C556 CMXE2J103J C MYLAR C557 CMYH3C682J C MYLAR C558 CMXM2A223J C MYLAR C559 CMYF2D225J C MYLAR C560 CEXF1H100V C ELECTRO C561 CEXF1H479V C ELECTRO C577 CCXB2H331K C CERA C801 CCZF1H104Z C CERA C802 CCZB1H102K C CERA C803 CEXF1C470V C ELECTRO C804 CMXM2A104J C MYLAR C806 CEXF1H109V C ELECTRO C807 CCZB1H223K C CERA C808 CCZF1H104Z C CERA C809 CEXF1C470V C ELECTRO C810 CEXF1H100V C ELECTRO C811 CCZF1H104Z C CERA C812 CEXF1H100V C ELECTRO C813 CCZF1H104Z C CERA C814 CEXF1H100V C ELECTRO C815 CCZF1H104Z C CERA C816 CEXF1C470V C ELECTRO C817 CCZF1H104Z C CERA C818 CCZF1H104Z C CERA C819 CCZF1H104Z C CERA C820 CCZF1H104Z C CERA C821 CCZF1H104Z C CERA C822 CCZF1H104Z C CERA C823 CCZF1H104Z C CERA C824 CMXM2A153J C MYLAR C825 CEXF1C470V C ELECTRO C826 CCZF1H104Z C CERA C827 CCZB1H391K C CERA
C828 CCZB1H391K C CERA C829 CCXF1H103Z C CERA C830 CEXF1C101V C ELECTRO C831 CCXF2H103Z C CERA CA801 9970780032 CGND 9970710243 CONN AS CDT CRT GND AS SOCKET CRT CONN WAFER CONN WAFER CONN WAFER DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE
16V RSS 100MF (6.3X11) TP ! CDT 9979615003
! CT301 9979300013
CW301 9979220009 CW801 485923272S CW802 485923282S D001 D2A05----D002 D2A05----D003 D2A05----D004 D2A05----D005 DD2L20U--D006 DHER107--D007 DZN4148--D008 DZN4148--D101 DRU1P----D102 DRG4-----D103 DD2L20U--D104 DD2L20U--D105 DZN4148--D106 DD2L20U--D201 DZN4148--D202 DZN4148--D203 DZN4148--D204 DZN4148--D231 DZN4148--D232 DZN4148--D501 DZN4148--D502 D1NS4----D503 DZN4148--D531 D1A5G-----
! ! 100V 0.1MF J (TP) 100V RSS 10MF (6.3X11) TP ! 100V 0.1MF J (TP) !
100V 0.022MF J TP 500VB1000PFK(TAPPING) 50V RSS 22MF (5X11) TP 100V 0.039MF J (TP) 630V PL 0.01MF J BUP 1.6KV 6800PF J BULK 100V 0.022MF J TP MPP 200V 2.2MF J 50V RSS 10MF (5X11) TP 50V RSS 4.7MF (5X11) TP 500VB330PF K (TAPPING) 50V HIKF 0.1MF Z 50V B 1000PF K 16V RSS 47MF (5X11) TP 100V 0.1MF J (TP) 50V RSS 1MF (5X11) TP HIBK50V0.022MFKAXL52 50V HIKF 0.1MF Z 16V RSS 47MF (5X11) TP 50V RSS 10MF (5X11) TP 50V HIKF 0.1MF Z 50V RSS 10MF (5X11) TP 50V HIKF 0.1MF Z 50V RSS 10MF (5X11) TP 50V HIKF 0.1MF Z 16V RSS 47MF (5X11) TP 50V HIKF 0.1MF Z 50V HIKF 0.1MF Z 50V HIKF 0.1MF Z 50V HIKF 0.1MF Z 50V HIKF 0.1MF Z 50V HIKF 0.1MF Z 50V HIKF 0.1MF Z 100V 0.015MF J (TP) 16V RSS 47MF (5X11) TP 50V HIKF 0.1MF Z 50V B 390PF K
D402 D1N4002A-- DIODE
D554 DDTV32F--- DIODE D556 D1N4937GP- DIODE D561 D1A5G----D567 DZN4148--D568 DRG4-----D569 DER206---D570 DER206---D590 D1A5G----D802 DZN4148--D804 DZN4148--D806 DZN4148--D831 DZN4148--D832 DZN4148--D833 DZN4148--D845 DZN4148--DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE
36
LOC
PART-CODE
PART-NAME
PART-DESC DG-526X UZ-18BM UZ-18BM DZ-5.1B DZ5.6BM DZ3.6B DZ-5.1B DZ-5.1B DZ-5.1B DZ-5.1B DZ-5.1B DZ-5.1B DZ15BM DZ15BM DZ-5.1B SEMKOTL3.15AH250VMF51 BSP3-H T0.4 SN 5.2 BSP3-H T0.4 SN 5.2 4.3+35404-9002+1015#18=50 KA3842B KA78R12 KA78L05AZ KS88P6232N 24C08 TDA9302H UPC1888CT KA2500 TDA9533 KS2508-02 BI3890 100UH K (AXIAL 7MM) TRL-526X 100UH K (AXIAL 3.5MM) 100UH K (AXIAL 3.5MM) LAL02TB 2.7UH M AXIAL 47UH K (AXIAL 3.5MM) 1UH K (AXIAL 3.5MM) 1UH K (AXIAL 3.5MM) 1UH K (AXIAL 3.5MM) CH-85B TCH-526X(110UH) SD50GYW(GREEN/AMBER) BNS-02AB2L-1 T=1.6*61*50 (526X) ECPAC140M290 2SK2101 KTC3198Y-(1815Y) (AUTO) KTA1281Y KTC3198Y-(1815Y) (AUTO) KTC3198Y-(1815Y) (AUTO) KTA1270Y(AUTO)(562Y)
LOC
PART-CODE
PART-NAME
PART-DESC KTA1024Y (949Y) KTC3198Y-(1815Y) (AUTO) KTC3198Y-(1815Y) (AUTO) KTC3202Y (AUTO)(1959Y) KTA1270Y(AUTO)(562Y) KTC3198Y-(1815Y) (AUTO) IRF630A KTC3198Y-(1815Y) (AUTO) KTC3198Y-(1815Y) (AUTO) KTA1270Y(AUTO)(562Y) KTA1270Y(AUTO)(562Y) KTA1270Y(AUTO)(562Y) KTC3198Y-(1815Y) (AUTO) IRF640 KTC3206Y (2229Y) IRF630A KTC3206Y (2229Y) KTA1270Y(AUTO)(562Y) KTC3202Y (AUTO)(1959Y) KSC 2383-Y 2SC5386 KSD1273-P KTA1270Y(AUTO)(562Y) KTC3198Y-(1815Y) (AUTO) 1/2 1M OHM J SR37 1W 33K OHM J (TAPPING) 1W 33K OHM J (TAPPING) 1W 33K OHM J (TAPPING) 1W 68K OHM J (TAPPING) 1W 68K OHM J (TAPPING) 1/6 1K OHM J 1/6 150K OHM F 1/6 4.7K OHM J 1/6 200K OHM J 1/6 26.7K OHM F 1/6 47K OHM J 1/6 22 OHM J 1/6 1K OHM J 1W0.27OHMJNON-INDUCT 1/6 1K OHM J 1/6 4.7K OHM J 1/4 56 OHM J 1/4 150K OHM J 1W 47 OHM J (TAPPING) 1/2 22 OHM J 1/6 200K OHM J 1/2 22 OHM J 1/6 100 OHM J 1/6 4.02K OHM F 1/6 10K OHM J 1/6 4.7K OHM J
! DG0015MG0000066 COIL DEGAUSSING
DZ001 DUZ18BM--- DIODE ZENER DZ002 DUZ18BM--- DIODE ZENER DZ101 DDZ5R1B--- DIODE ZENER DZ200 DDZ5R6BM-- DIODE ZENER DZ201 DDZ3R6B--- DIODE ZENER DZ231 DDZ5R1B--- DIODE ZENER DZ232 DDZ5R1B--- DIODE ZENER DZ233 DDZ5R1B--- DIODE ZENER DZ234 DDZ5R1B--- DIODE ZENER DZ235 DDZ5R1B--- DIODE ZENER DZ501 DDZ5R1B--- DIODE ZENER DZ532 DDZ15BM--- DIODE ZENER DZ533 DDZ15BM--- DIODE ZENER DZ801 DDZ5R1B--- DIODE ZENER F001 5F3CB3122L FUSE CERA F001A 9977410900 F001B 9977410900 GND2 9970700123 IC001 1KA3842B-IC101 1KA78R12-FUSE CLIP FUSE CLIP CONN AS IC POWER IC REGULATOR
Q203 TZTA1024Y- TR Q231 TZTC3198Y- TR Q401 TZTC3198Y- TR Q501 TZTC3202Y- TR Q502 TZTA1270Y- TR Q503 TZTC3198Y- TR Q504 T1RF630A-FET Q505 TZTC3198Y- TR Q506 TZTC3198Y- TR Q507 TZTA1270Y- TR Q508 TZTA1270Y- TR Q509 TZTA1270Y- TR Q510 TZTC3198Y- TR Q534 T1RF640--Q536 T1RF630A-FET FET Q535 TZTC3206Y- TR Q537 TZTC3206Y- TR Q551 TZTA1270Y- TR Q552 TZTC3202Y- TR Q553 TKSC2383Y- TR Q554 T2SC5386-TR H.OUT Q601 TKSD1273P- TR Q801 TZTA1270Y- TR Q802 TZTC3198Y- TR R001 RC-2Z105JR002 RS01Z333JR003 RS01Z333JR004 RS01Z333JR005 RS01Z683JR006 RS01Z683JR008 RD-AZ102JR010 RD-AZ472JR011 RD-AZ204JR013 RD-AZ473JR015 RD-AZ220JR016 RD-AZ102JR018 RD-AZ102JR019 RD-AZ472JR020 RD-4Z560JR101 RD-4Z154JR102 RS01Z470JR103 RD-2Z220JR105 RD-AZ204JR106 RD-2Z220JR107 RD-AZ101JR110 RD-AZ103JR112 RD-AZ472JR CARBON COMP R M-OXIDE FILM R M-OXIDE FILM R M-OXIDE FILM R M-OXIDE FILM R M-OXIDE FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R M-OXIDE FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM
IC102 1KA78L05AZ IC REGULATOR IC201 1KS88P6232 IC MICOM IC202 124C08---IC EEPROM IC401 1TDA9302H- IC VERTICAL IC501 1UPC1888CT IC H/V OSC IC801 1KA2500--IC802 1TDA9533-J132 5PB13890-IC IC VIDEO OUTPUT COIL BEAD
IC803 1DW0SD10-- IC OSD L501 5CPZ101K03 COIL PEAKING L531 5MH0000070 COIL H-LINEARITY L801 5CPZ101K02 COIL PEAKING L802 5CPZ101K02 COIL PEAKING L803 5CPZ279K02 COIL PEAKING L804 5CPZ470K02 COIL PEAKING L831 5CPZ109K02 COIL PEAKING L832 5CPZ109K02 COIL PEAKING L833 5CPZ109K02 COIL PEAKING L834 5MC0000078 COIL CHOKE L835 5MC0000074 COIL CHOKE LED1 DSD50GYW-- LED
R009 RN-AZ1503F R METAL FILM
R012 RN-AZ2672F R METAL FILM
R017 RW01Z278JN R WIRE WOUND
! P001 9979500022
PCB 9979800545
RECEPTACLE PCB CRT FET
! PR001 DECPAC140M POSISTOR
Q001 T2SK2101-Q002 TZTC3198Y- TR Q103 TKTA1281Y- TR Q104 TZTC3198Y- TR Q201 TZTC3198Y- TR Q202 TZTA1270Y- TR
R108 RN-AZ4021F R METAL FILM
37
LOC
PART-CODE
PART-NAME R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM
PART-DESC 1/6 10K OHM J 1/4 91 OHM J 1/4 470 OHM J 1/6 1K OHM J 1/6 1K OHM J 1/6 1K OHM J 1/6 150 OHM J 1/6 390 OHM J 1/6 390 OHM J 1/6 10K OHM J 1/6 10K OHM J 1/6 4.7K OHM J 1/6 100 OHM J 1/6 4.7K OHM J 1/6 4.7K OHM J 1/6 100 OHM J 1/6 10K OHM J 1/6 1.2K OHM J 1/6 20K OHM J 1/6 100 OHM J 1/6 1.2K OHM J 1/6 100 OHM J 1/6 1.2K OHM J 1/6 10K OHM J 1/6 10K OHM J 1/6 100 OHM J 1/6 100 OHM J 1/6 2K OHM J 1/6 1.2K OHM J 1/6 100 OHM J 1/6 1.2K OHM J 1/6 100 OHM J 1/6 10K OHM J 1/6 120K OHM J 1/6 62K OHM J 1/6 20K OHM J 1/4 1.2K OHM J 1/4 1.2K OHM J 1/6 10K OHM J 1/6 4.7K OHM J 1/6 4.7K OHM J 1/4 1.2K OHM J 1/4 100 OHM J 1/4 100 OHM J 1/4 100 OHM J 1/4 4.7K OHM J
LOC
PART-CODE
PART-NAME
PART-DESC 1/6 10.4K OHM F 1/6 3.3K OHM J 1/6 8.2K OHM J 1/4 470 OHM J 1/4 220 OHM J 1W 200 OHM J (TAPPING) 1/4 1.5 OHM J 1/4 39 OHM J 1/6 5.6K OHM F 1/6 1.21K OHM F 1/6 10.6K OHM F 1/4 1.8 OHM F 1/4 1.8 OHM F 1/6 1M OHM J 1/6 18K OHM J 1/6 1K OHM J 1/6 100 OHM J 1/6 100 OHM J 1/6 300K OHM J 1/6 100 OHM J 1/6 6.8K OHM J 1/6 10K OHM J 1/6 56K OHM J 1/6 464K OHM F 1/6 56.2K OHM F 1/6 1.7K OHM F 1/6 1.5K OHM J 1/6 1K OHM J 1/6 1K OHM J 1/6 100 OHM J 1/6 100 OHM J 1W 100 OHM J (TAPPING) 1/6 10.4K OHM F 1/6 1.37K OHM F 1/6 1K OHM F 1/6 470 OHM J 1/4 100K OHM J 1/6 150K OHM J 1/6 100K OHM J 1/4 100K OHM J 1/6 150K OHM J 1/6 100K OHM J 1/6 2K OHM J 1/4 15K OHM J 1/4 5.6K OHM J 2W 300 OHM J (TAPPING) 1/6 470 OHM J 1/4 56 OHM J 1/6 36K OHM J 1/6 2.2K OHM J 1W0.47OHMJNON-INDUCT
R114 RD-AZ103JR115 RD-4Z910JR116 RD-4Z471JR117 RD-AZ102JR118 RD-AZ102JR119 RD-AZ102JR201 RD-AZ151JR202 RD-AZ391JR203 RD-AZ391JR204 RD-AZ103JR205 RD-AZ103JR206 RD-AZ472JR214 RD-AZ101JR215 RD-AZ472JR216 RD-AZ472JR217 RD-AZ101JR218 RD-AZ103JR219 RD-AZ122JR220 RD-AZ203JR221 RD-AZ101JR222 RD-AZ122JR223 RD-AZ101JR224 RD-AZ122JR226 RD-AZ103JR227 RD-AZ103JR228 RD-AZ101JR229 RD-AZ101JR230 RD-AZ202JR231 RD-AZ122JR232 RD-AZ101JR233 RD-AZ122JR234 RD-AZ101JR235 RD-AZ103JR237 RD-AZ124JR238 RD-AZ623JR239 RD-AZ203JR240 RD-4Z122JR241 RD-4Z122JR242 RD-AZ103JR243 RD-AZ472JR245 RD-AZ472JR301 RD-4Z122J(R4) R302 RD-4Z101J(R3) R303 RD-4Z101J(R2) R304 RD-4Z101J(R1) R305 RD-4Z472J(R5)
R401 RN-AZ1042F R METAL FILM R402 RD-AZ332JR403 RD-AZ822JR404 RD-4Z471JR406 RD-4Z221JR407 RS01Z201JR408 RD-4Z159JR409 RD-4Z390JR CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R M-OXIDE FILM R CARBON FILM R CARBON FILM
R410 RN-AZ5601F R METAL FILM R411 RN-AZ1211F R METAL FILM R412 RN-AZ1062F R METAL FILM R413 RN-4Z1808F R METAL FILM R414 RN-4Z1808F R METAL FILM R502 RD-AZ105JR503 RD-AZ183JR504 RD-AZ102JR505 RD-AZ101JR507 RD-AZ101JR509 RD-AZ304JR511 RD-AZ101JR512 RD-AZ682JR513 RD-AZ103JR514 RD-AZ563JR CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM
R515 RN-AZ4643F R METAL FILM R516 RN-AZ5622F R METAL FILM R517 RN-AZ1701F R METAL FILM R518 RD-AZ152JR519 RD-AZ102JR520 RD-AZ102JR521 RD-AZ101JR522 RD-AZ101JR531 RS01Z101JR CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R M-OXIDE FILM
R532 RN-AZ1042F R METAL FILM R533 RN-AZ1371F R METAL FILM R534 RN-AZ1001F R METAL FILM R535 RD-AZ471JR540 RD-4Z104JR541 RD-AZ154JR543 RD-AZ104JR544 RD-4Z104JR545 RD-AZ154JR547 RD-AZ104JR548 RD-AZ202JR550 RD-4Z153JR551 RD-4Z562JR552 RS02Z301JR553 RD-AZ471JR554 RD-4Z560JR555 RD-AZ363JR556 RD-AZ222JR CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R M-OXIDE FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM
R557 RW01Z478JN R WIRE WOUND
38
LOC
PART-CODE
PART-NAME R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM
PART-DESC 1/4 10 OHM J 1/6 10K OHM J 1/6 20K OHM J 1/6 47K OHM J 1/6 91K OHM J 1/4 2.2K OHM J 1/6 30K OHM J 1/4 220K OHM J 1/6 10K OHM J 1/6 36.5K OHM F 1/6 36.5K OHM F 1/6 1K OHM J 1/6 20K OHM J 1/4 30K OHM J 1/6 4.7K OHM J 1/6 2.2K OHM J 1W 1.5K OHM J (TAPPING) 1/6 10K OHM J 1/6 36K OHM J 1/2 1 OHM J 1/4 470K OHM J 1/6 56.2K OHM F 1/6 56.2K OHM F 1/6 3.3K OHM J 1/6 36.5K OHM F 1/6 30K OHM J 1/6 1M OHM J 1/6 6.2K OHM J 1/6 5.6K OHM J 1/6 47K OHM J 1/6 27K OHM J 1/6 100 OHM J 1/6 75 OHM J 1/6 75 OHM J 1/6 75 OHM J 1/6 470 OHM J 1/6 10 OHM J 1/6 470 OHM J 1/6 560 OHM J 1/6 10 OHM J 1/6 470 OHM J 1/6 10 OHM J 1/6 6.8K OHM J 1/6 6.8K OHM J 1/6 5.76K OHM F 1/6 100 OHM J
LOC
PART-CODE
PART-NAME R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM SW RELAY CABLE SIGNAL AS
PART-DESC 1/6 100 OHM J 1/6 100 OHM J 1/6 560 OHM J 1/6 560 OHM J 1/6 560 OHM J 1/6 470 OHM J 1/6 470 OHM J 1/4 150K OHM J 1/6 150 OHM J 1/6 150 OHM J 1/6 150 OHM J 1/4 91 OHM J 1/4 91 OHM J 1/6 33 OHM J 1/6 33 OHM J 1/6 33 OHM J 1/6 10M OHM J 1/6 10M OHM J 1/6 10M OHM J 1/6 12K OHM J 1/6 12K OHM J 1/6 3K OHM J 1/6 10K OHM J 1/6 1K OHM J 1/6 270 OHM J KI-S-112M1C-1P(HR-CR313) 15P+1C/DDC=1.5M(GY286A) S-23 1.5KV S-23 1.5KV S-23 1.5KV KPT-1115VM 1C-1P KPT-1115VM 1C-1P KPT-1115VM 1C-1P KPT-1115VM 1C-1P KPT-1115VM 1C-1P DMT-526X DST-603 DDT-526X FFA73336U TP8D13 CCT065AT2KOHMBTAP CCT 063BT 500 OHM B TAP HC-49/U12.00000MHZ30PPM
R560 RD-4Z100JR561 RD-AZ103JR562 RD-AZ203JR563 RD-AZ473JR564 RD-AZ913JR565 RD-4Z222JR566 RD-AZ303JR567 RD-4Z224JR568 RD-AZ103J-
R822 RD-AZ101JR823 RD-AZ101JR824 RD-AZ561JR825 RD-AZ561JR826 RD-AZ561JR827 RD-AZ471JR828 RD-AZ471JR829 RD-4Z154JR831 RD-AZ151JR833 RD-AZ151JR835 RD-AZ151JR837 RD-4Z910JR838 RD-4Z910JR839 RD-AZ330JR840 RD-AZ330JR841 RD-AZ330JR848 RD-AZ106JR849 RD-AZ106JR850 RD-AZ106JR851 RD-AZ123JR852 RD-AZ123JR853 RD-AZ302JR854 RD-AZ103JR855 RD-AZ102JR856 RD-AZ271J-
R569 RN-AZ3652F R METAL FILM R570 RN-AZ3652F R METAL FILM R572 RD-AZ102JR573 RD-AZ203JR574 RD-4Z303JR575 RD-AZ472JR576 RD-AZ222JR577 RS01Z152JR588 RD-AZ103JR589 RD-AZ363JR590 RD-2Z109JR591 RD-4Z474JR CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R M-OXIDE FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM
R592 RN-AZ5622F R METAL FILM R594 RN-AZ5622F R METAL FILM R595 RD-AZ332JR801 RD-AZ303JR802 RD-AZ105JR803 RD-AZ622JR804 RD-AZ562JR805 RD-AZ473JR806 RD-AZ273JR807 RD-AZ101JR808 RD-AZ750JR809 RD-AZ750JR810 RD-AZ750JR811 RD-AZ471JR812 RD-AZ100JR813 RD-AZ471JR814 RD-AZ561JR815 RD-AZ100JR816 RD-AZ471JR817 RD-AZ100JR818 RD-AZ682JR819 RD-AZ682JR821 RD-AZ101JR CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R596 RN-AZ3652F R METAL FILM
! RL001 5SC0101006
SC001 9970800033 (SG1)
SG301 4SG0D00104 SPARK GAP SG302 4SG0D00104 SPARK GAP (SG2) SG303 4SG0D00104 SPARK GAP (SG3) SW0015S50101Z01 SW002 5S50101Z01 SW003 5S50101Z01 SW004 5S50101Z01 SW005 5S50101Z01 SW TACT SW TACT SW TACT SW TACT SW TACT
! T001 5RM0000099 TRANS SMPS ! T002 5RY0000002 TRANS SYNC
T501 5RD0000047 TRANS DRIVE T601 5RH0000125 FBT
! TH001 DTP8D13---
THERMISTOR
VR001 RV6421202P R SEMI FIXED VR501 RV6121501P R SEMI FIXED X201 5XE12R000E CRYSTAL QUARTZ
R820 RN-AZ5761F R METAL FILM
39
DAEWOO ELECTRONICS CO., LTD
686, AHYEON-DONG MAPO-GU SEOUL, KOREA C.P.O. BOX 8003 SEOUL, KOREA TELEX : DWELEC K28177-8 CABLE : "DAEWOOELEC" E-mail : [email protected]
PRINTED DATE : APRIL, 2000