Text preview for : toshiba_32a3030d_full_sm.pdf part of TOSHIBA toshiba 32a3030d full sm TOSHIBA LCD 32A3030D toshiba_32a3030d_full_sm.pdf
Back to : toshiba_32a3030d_full_sm. | Home
. 1 1
LCD Color Television
32A3030D Ver. 2.00
file://D:\Documents and Settings\Admin\ \TOSHIBA 32A3030D-01 lcd\... 27.06.2015
ADJUSTMENT [LCD Color Television] ASIA_EU . 1 21
ADJUSTMENT
Service Mode
Entering to Service Mode
1. Set VOLUME to minimum and press
button once on remote control.
2. Press button again and hold button down.
Service Mode display
3. While holding the button, press MENU
button on TV set.
file://D:\Documents and Settings\Admin\ \TOSHIBA 32A3030D-01 lcd\... 27.06.2015
ADJUSTMENT [LCD Color Television] ASIA_EU . 2 21
Displaying the Adjustment Menu
Press MENU button on TV.
Service Mode
Press Press
Adjustment Mode
Key Function in the Service Mode
The following key entry during display of adjustment menu provides special functions.
CAUTION: Never try to perform initialization unless you have changed the
memory IC.
button (on remote control)
file://D:\Documents and Settings\Admin\ \TOSHIBA 32A3030D-01 lcd\... 27.06.2015
ADJUSTMENT [LCD Color Television] ASIA_EU . 3 21
Test signal selection
Selection of the adjustment items CH (on TV or remote control)
Change of the data value Volume +/- (on TV or remote control)
Adjustment menu mode ON/OFF MENU button (on TV)
Initialization of the memory (QA02) CALL + CH button on TV
Reset the count of operating
CALL + CH button on TV
protect circuit to "00"
Turn off I2C bus communication CALL + Volume + button on TV
"RCUT" selection 1 button
"GCUT" selection 2 button
"BCUT" selection 3 button
"CNTX" selection 4 button
"COLC" selection 5 button
"UVTT" selection 6 button
Automatic A/D Adjustment
7 button
(PC, Component, Composite (PAL, NTSC))
Self diagnostic display ON/OFF 9 button
Selecting the Adjusting Item
Every pressing of CH button in the service mode changes the adjustment items in the
order of table below. ( button for reverse order)
SETTING & ADJUSTING DATA
[ SERVICE MODE ]
ADJUSTING ITEMS AND DATA IN THE SERVICE MODE:
Note:
The image system data of RCUT-BDRV is different by each image format.
The PAL value is indicated in the table.
Never adjust H.POS and V.POS except PAL/WIDE mode.
file://D:\Documents and Settings\Admin\ \TOSHIBA 32A3030D-01 lcd\... 27.06.2015
ADJUSTMENT [LCD Color Television] ASIA_EU . 4 21
Item Name of adjustment
RCUT R CUT OFF
GCUT G CUT OFF
BCUT B CUT OFF
RDRV R DRIVE
GDRV G DRIVE
BDRV B DRIVE
BRTC BRIGHTNESS CENTER
COLC COLOR CENTER
UVTT BASE BAND TINT
CNTX CONTRAST MAX
VOLUX MAX VOLUME LIMITED
PLLW0 PLL WAIT TIME
PLLW1 PLL WAIT TIME
PLLW2 PLL WAIT TIME
PLLW3 PLL WAIT TIME
PLLW4 PLL WAIT TIME
PLLW5 PLL WAIT TIME
OPT1 TV SET OPTION 1
OPT2 TV SET OPTION 2
OPT3 TV SET OPTION 3
OPT4 TV SET OPTION 4 (PANEL OPT DATA FOR VENDOR)
OPT5 TV SET OPTION 5 (PANEL OPT DATA FOR SIZE)
OPT6 TV SET OPTION 6 (HOTEL MODE)
OPT7 TV SET OPTION 7 (HOTEL MODE)
OPT8 TV SET OPTION 8 (HOTEL MODE)
TVOP TV SET OPTION
ID MODEL ID
BDWID BORDER WIDTH FOR EXACT SCAN
BDHIT BORDER HEIGHT FOR EXACT SCAN
FPLG MASK_ENABLE (SD/HD)
file://D:\Documents and Settings\Admin\ \TOSHIBA 32A3030D-01 lcd\... 27.06.2015
ADJUSTMENT [LCD Color Television] ASIA_EU . 5 21
FPLG2 Channel LOGO Vector Clip SW (SD)
FPLG3 Channel LOGO Vector Clip SW (HD)
Factory preset data will be loaded after setting Model ID data.
(Refer to Initialization of Memory Data of QA02 and setting data of signal board.)
Adjusting the Data
Pressing of VOLUME +/- button will change the value of data in the range from 00H to
FFH. The variable range depends on the adjusting item.
I2C Bus Off
Turn off I2C communication between IC700 and IC400.
1) Press and hold the CALL button on the remote control, then press the Volume
+ button on the TV.
2) Display "BUS Off" OSD.
3) I2C communication turned off.
Note:
To return Bus on status, press and hold the CALL button on the remote control, then press
the Volume + button on the TV again. TV will be turned off and automatically turned
on, then status will be Bus On.
Setting TVOP
Enter to service mode and select menu of TVOP by pressing P or P during display of
adjustment menu. After selecting TVOP, press + or - to set I2C check function to
disable or enable as below.
TVOP FUNCTION DESCRIPTION 1 0 (Normal)
D5 (bit5) I2C check between IC700 and IC400. (WDT) Disable Enable
file://D:\Documents and Settings\Admin\ \TOSHIBA 32A3030D-01 lcd\... 27.06.2015
ADJUSTMENT [LCD Color Television] ASIA_EU . 6 21
Setting Panel Option Data
Panel option data is subject to OP4 and OP5.
Enter to service mode and select menu of OPT4 or OPT5 by pressing P or P during
display of adjustment menu. After selecting OPT4 or OPT5, press + or - to set OPT4
or OPT5 value as table below.
Panel option data
Series Model name Panel vendor OPT4 value OPT5 value
A3000 EU Digital/Ready 26A3030D/A3000P LPL 0x01 0x03
IPS 0x07 0x03
32A3030D/A3000P LPL 0x01 0x05
IPS 0x07 0x05
37A3030D/A3000P LPL 0x01 0x06
IPS 0x07 0x06
42A3030D/A3000P LPL 0x01 0x07
OP4
Ex. OPT4 value 0x05 indicates that panel vendor is AUO AMVA.
OPT4
D7 D6 D5 D4 D3 D2 D1 D0
(bit7) (bit6) (bit5) (bit4) (bit3) (bit2) (bit1) (bit0)
Panel vendor LPL - - - - 0 0 0 1
SHP - - - - 0 0 1 0
CMO - - - - 0 0 1 1
AUO PMVA - - - - 0 1 0 0
AUO AMVA - - - - 0 1 0 1
SAMSUNG - - - - 0 1 1 0
IPS - - - - 0 1 1 1
OP5
file://D:\Documents and Settings\Admin\ \TOSHIBA 32A3030D-01 lcd\... 27.06.2015
ADJUSTMENT [LCD Color Television] ASIA_EU . 7 21
Ex. OPT5 value 0x05 indicates that panel size is 32.
OPT5
D7 D6 D5 D4 D3 D2 D1 D0
(bit7) (bit6) (bit5) (bit4) (bit3) (bit2) (bit1) (bit0)
Size 32 - - - - 0 1 0 1
37 - - - - 0 1 1 0
42 - - - - 0 1 1 1
Convert from Bit (Binary) to Hex
The table for converting from bit (D7-D0) to hex (0x**).
BIT (Binary)
High nibble D7 D6 D5 D4
Low nibble D3 D2 D1 D0
HEX 0 0 0 0 0
1 0 0 0 1
2 0 0 1 0
3 0 0 1 1
4 0 1 0 0
5 0 1 0 1
6 0 1 1 0
7 0 1 1 1
8 1 0 0 0
9 1 0 0 1
A 1 0 1 0
B 1 0 1 1
C 1 1 0 0
D 1 1 0 1
E 1 1 1 0
F 1 1 1 1
file://D:\Documents and Settings\Admin\ \TOSHIBA 32A3030D-01 lcd\... 27.06.2015
ADJUSTMENT [LCD Color Television] ASIA_EU . 8 21
E.g. If Bit D7-0 = 0101 1010, Hex data is 0x5A.
Exit from Service Mode
Pressing POWER button to turn off the TV once.
Initialization of Memory Data of QA02 and Setting Data of Signal Unit
After replacing QA02 or signal board, the following initialization is required.
CAUTION: Never attempt to initialize the data unless QA02 has been
replaced.
Whenever using new signal board to the set, setting the Model ID data
according to Panel option data.
1) Enter the service mode.
2) Select menu of ID by pressing P or P during display of adjustment menu in the
service mode.
3) Change ID data into MODEL ID to initialize by pressing + or -., refer to table
below.
4) Press and hold the CALL button on the remote control, then press the CHANNEL
button on the TV.
5) Initialization progress dialog including model name and panel vendor is shown.
Progress status is "WRITING".
6) Progress status is changed "OK" and power cycle (automatically). Then QA02
initialization has been completed.
7) Enter the service mode and select version check mode. Confirm if model name and
model id set is correct. If not, repeat steps 1) to 6).
file://D:\Documents and Settings\Admin\ \TOSHIBA 32A3030D-01 lcd\... 27.06.2015
ADJUSTMENT [LCD Color Television] ASIA_EU . 9 21
Note:
In case initialization by setting wrong MODEL ID is done, there is a possibility of
abnormal display.
8) Set I2C check function of TVOP to enable.
9) Check the picture carefully. If necessary, adjust any adjustment item above.
Perform "Auto tune" on the owner's manual.
MODEL ID (HEX) Model name Panel vendor
0x01 26A3000P LPL
0x02 26A3000P IPS
0x03 32A3000P LPL
0x04 32A3000P IPS
0x05 37A3000P LPL
0x06 37A3000P IPS
0x07 42A3000P LPL
0x08 26A3030D LPL
0x09 26A3030D IPS
0x10 32A3030D LPL
0x11 32A3030D IPS
0x12 37A3030D LPL
0x13 37A3030D IPS
0x14 42A3030D LPL
0x15
0x16
0x17
0x18
0x19
0x20
0x21
0x22
0x23
0x24
0x25
file://D:\Documents and Settings\Admin\ \TOSHIBA 32A3030D-01 lcd\... 27.06.2015
ADJUSTMENT [LCD Color Television] ASIA_EU . 10 21
0x26
0x27
0x28
0x29
0x30
0x31
0x32
0x33
Initializing Data setting flowchart after replacing the Signal Unit
file://D:\Documents and Settings\Admin\ \TOSHIBA 32A3030D-01 lcd\... 27.06.2015
ADJUSTMENT [LCD Color Television] ASIA_EU . 11 21
Test Signal Selection
file://D:\Documents and Settings\Admin\ \TOSHIBA 32A3030D-01 lcd\... 27.06.2015
ADJUSTMENT [LCD Color Television] ASIA_EU . 12 21
Every pressing of button on the remote control changes the built-in test patterns on
screen as described below in Service Mode.
Picture Signal
Red raster
Green raster
Blue raster
All Black
All White
Self Diagnostic Function
1. Press "9" button on remote control during display of adjustment menu in the service
mode. The diagnosis will begin to check if interface among IC's is executed properly.
2. During diagnosis, the following displays are shown.
* Self check display and Item are subject to the models.
file://D:\Documents and Settings\Admin\ \TOSHIBA 32A3030D-01 lcd\... 27.06.2015
ADJUSTMENT [LCD Color Television] ASIA_EU . 13 21
(1) Firmware :
Version information of microprocessor
Series name (AAAA) and market area (BB) and software program version (0000)
(2) Time : Total hour of turn the TV on. (Unit : H)
(3) BL_STATUS :
Counter for saving BackLight on error.
This value is counted till 99 (Decimal).
(4) Bus line : -- "OK" is normal
SCL-GND (Red indication) : SCL-GND short circuit
SDA-GND (Red indication) : SDA-GND short circuit
SCL-SDA (Red indication) : SCL-SDA short circuit
(5) Bus cont : --- "OK" is normal.
NG is abnormal (Red indication).
When the abnormal status is detected, type name of semiconductor is
indicated in red colour.
(6) Block
UV : TV reception mode
V1 - V9 : VIDEO 1-9 input mode
PC : PC mode
YUV : YUV mode
DTV : DTV mode
UV RF
1
V1
(SCART (FULL))
2
file://D:\Documents and Settings\Admin\ \TOSHIBA 32A3030D-01 lcd\... 27.06.2015
ADJUSTMENT [LCD Color Television] ASIA_EU . 14 21
V2 (SCART (S+AV))
3
V3
(Component/Composite)
V4 HDMI1
V5 --
V6 --
V7 --
V8 --
V9 --
PC PC
YUV --
DTV --
Version Check Mode
1. Press "9" button twice on remote control during display of adjustment menu in the
service mode.
The version of main MPU will be checked.
2. During Version Check, the following displays are shown.
* Version check display and Item are subject to the models.
file://D:\Documents and Settings\Admin\ \TOSHIBA 32A3030D-01 lcd\... 27.06.2015
ADJUSTMENT [LCD Color Television] ASIA_EU . 15 21
(1) MAIN MPU :
Version information of microprocessor
Series name and Code Program Version (4 figure number) and OSD Version (2 figure
number).
(2) EEPROM :
Version information of EEPROM : Display 1 byte data.
(3) SUB MPU :
Version information of SUB MPU : Display 1 byte data.
(4) OPTION :
Option information : Display six numbers of 1 byte data.
(5) HDMI ID :
HDMI ID information : Display 4 byte data.
(6) SW Ver
Version information of DB software as Toshiba release. (Only digital model.)
(7) MW Ver
Left side is Application and UI version information of DB software. (Only digital
model.)
Right side is Firmware (Driver) version information of DB software. (Only digital
model.)
file://D:\Documents and Settings\Admin\ \TOSHIBA 32A3030D-01 lcd\... 27.06.2015
ADJUSTMENT [LCD Color Television] ASIA_EU . 16 21
(8) A/D Adjust
A/D adjustment item.
--MAIN : It's enable only in double Window model. A/D adjustment status of main
picture.
--PIP : It's enable only in double Window model. A/D adjustment status of sub
picture.
--COMP : Component input
--PC : PC input
--NTSC : NTSC (60 Hz) SD signal (composite input).
--PAL : PAL (50 Hz) SD signal (composite input).
--OK : A/D adjustment set correctly.
--NG : A/D adjustment set incorrect.
-- : A/D adjustment is not needed. Because its picture format isn't used.
(9) 100 Hz FPGA Software Version
It's enable only in 100 Hz drive panel model.
Upper 2 figure number means function versions of double frequency convert.
Lower 2 figure number means function version of vector complement.
(10) Memory Data Version
Version information of EEPROM.
DRMA**** means model number of EEPROM.
REV** means version of EEPROM.
(11) CD number
CD information (ascii code). : Display 4 byte data.
(12) Model Name
Model name information (ascii code). : Display 7 byte data.
(13) LCD Panel Vendor information display
The following Panel Vendor (DDD) and screen size (00) are displayed.
Example : AUO-32 indicates that Vendor is AUO and Screen Size is 32 inch
Status Check Mode
1. Press "9" button thrice on remote control during display of adjustment menu in the
service mode.
The status of this model will be checked.
2. During Status Check, the following displays are shown.
file://D:\Documents and Settings\Admin\ \TOSHIBA 32A3030D-01 lcd\... 27.06.2015
ADJUSTMENT [LCD Color Television] ASIA_EU . 17 21
* Status check display and Item are subject to the models.
(1) MAIN :
Main source information :
Display RF position number (0 - 99) on the main screen, or Input Source
(EXT1/2/3/HDMI etc.)
(2) MAIN FORMAT :
Display Video and PC format information
(3) MAIN PLL :
Main PLL information : Display 1 byte data at five.
(4) SUB :
Sub source information :
Display RF position number (0 - 99) on the Sub screen, or Input Source
(EXT1/2/3/HDMI etc.)
This item displays only Double window model.
(5) SUB FORMAT :
Display Video and PC format information
This item displays only Double window model.
(6) SUB PLL :
Sub PLL information : Display 1 byte data at five.
This item displays only Double window model.
(7) SCREEN SIZE :
Display the screen size as follows.
Exact Scan
Wide
Super Live 2
file://D:\Documents and Settings\Admin\ \TOSHIBA 32A3030D-01 lcd\... 27.06.2015
ADJUSTMENT [LCD Color Television] ASIA_EU . 18 21
Cinema 2
4:3
Super Live 1
Cinema 1
Subtitle
14:9
Note:
Exact Scan is shown only for 1080p panel model with video input mode except pc.
(8) OTHER STATUS :
Other status information : Display three numbers of 2 byte data.
Setting Hotel Mode
Enter to service mode and select Hotel Mode menu by pressing P or P .
After selecting Hotel Mode, press + to enter details setting in Hotel Mode.
To select menu, press P or P and press OK to enter the adjustment menu of table bellow.
To move the cursor in the adjustment, press + or -.
1. By pressing P or P , OPT2 setting will change the value either 1 or 0 on selected
items as follows;
OP2
OPT2 FUNCTION DESCRIPTION 1 0 (Normal)
D7 (bit7) - (no use) - -
D6 (bit6) - (no use) - -
D5 (bit5) FRONT Key Disable Enable
D4 (bit4) All keys except input selector key Disable Enable
(Video/TV)
D3 (bit3) User remote control operation Disable Enable
(Service mode and Supere
User mode may possible to
setting only)
D2 (bit2) Disable SET UP MENU except Disable Enable
file://D:\Documents and Settings\Admin\ \TOSHIBA 32A3030D-01 lcd\... 27.06.2015
ADJUSTMENT [LCD Color Television] ASIA_EU . 19 21
language. (Display the language only)
(tuning SETUP MENU)
D1 (bit1) Disable SETUP MENU Disable Enable
D0 (bit0) HOTEL Mode On (Enable the setting of D1 Off
from to D7) (Normal)
VOLUX
Set VOLUX as following.
1) Set speaker volume to 100. (Any value is OK, but 100 is better to check sound level.)
2) Down value of VOLUX until finding suitable sound volume level.
VOLUX FUNCTION DESCRIPTION 1 0 (Normal)
D7 (bit7) ~
Max Limiter of Volume Control 0x00 ~ 0x7F (Normal: 0x7C)
D0 (bit0)
OP6
OPT6 FUNCTION DESCRIPTION 1 0 (Normal)
D7 (bit7) Enable mode that POS or VIDEO program Enable Disable
number will be appeared in forced when turn
ON the main power
D6 (bit6) ~ POS or VIDEO program number 0 ~ 127 [decimal] (Normal: 0)
D0 (bit0) POS number: 0 ~ 99
VIDEO number: 100 ~ 127
(DTV = 100, VIDEO = 101,
VIDEO = 102..)
100 is used as ATV when
DTV option is disable.
OP7
OPT7 FUNCTION DESCRIPTION 1 0 (Normal)
D7 (bit7) Enable mode that speaker volume will be set Enable Disable
in forced when turn ON the main power
D6 (bit6) ~ Forced speaker volume 0 ~ 100 [decimal] (Normal: 0)
file://D:\Documents and Settings\Admin\ \TOSHIBA 32A3030D-01 lcd\... 27.06.2015
ADJUSTMENT [LCD Color Television] ASIA_EU . 20 21
D0 (bit0) Value above 100 is no effect.
OP8
OPT8 FUNCTION DESCRIPTION 1 0 (Normal)
D7 (bit7) ~ - (no use) - -
D3 (bit3)
D2 (bit2) Enable mode that picture mode will be set in Enable Disable
forced when turn ON the main power (Display the
language only)
D1 (bit1) ~ Forced picture mode 0 [dec]: Dynamic (mode-1)
D0 (bit0) (Normal)
1 [dec]: Standard (mode-2)
2 [dec]: Mild (mode-3)
3 [dec]: Memory (mode-M)
LED Indication
The Green and Red LEDs on the TV (at the bottom center of the TV) indicate the TV's
status, as described below.
Red ON (solid) and Green OFF = The TV power cord is plugged in.
Green ON (solid) and Red ON = The On timer is operating.
LED Indication Condition Solution
1 Green is OFF; Abnormal operation Turn OFF the TV and unplug
Red blinks continuously at 0.5- the power cord.
second intervals. Plug the power cord in again
and turn ON the TV.
2 Green is OFF; Abnormal operation of Turn OFF the TV and unplug
Red blinks continuously at 1- BUS line. the power cord.
second intervals. Plug the power cord in again
and turn ON the TV.
file://D:\Documents and Settings\Admin\ \TOSHIBA 32A3030D-01 lcd\... 27.06.2015
ADJUSTMENT [LCD Color Television] ASIA_EU . 21 21
file://D:\Documents and Settings\Admin\ \TOSHIBA 32A3030D-01 lcd\... 27.06.2015
. 1 1
FUNCTION AND OPERATION
The Remote Control
Simple at-a-glance reference of your remote control.
file://D:\Documents and Settings\Admin\ \TOSHIBA 32A3030D-01 lcd\... 27.06.2015
. 1 2
FUNCTION AND OPERATION
Controls and Input Connections
A wide variety of external equipment can be connected to the input sockets on the side of the
television.
Whilst all the necessary adjustments and controls for the television are made using the remote
control, the buttons on the television may be used for some functions.
Switching On
Using the Remote Control
file://D:\Documents and Settings\Admin\ \TOSHIBA 32A3030D-01 lcd\... 27.06.2015
. 2 2
Using the Controls and Connections
file://D:\Documents and Settings\Admin\ \TOSHIBA 32A3030D-01 lcd\... 27.06.2015
. 1 3
FUNCTION AND OPERATION
Tuning Digital Television for the First Time
Before switching on the television put your decoder and media recorder to Standby if they
are connected and ensure the aerial is connected. To set up the television use the buttons on
the remote control.
file://D:\Documents and Settings\Admin\ \TOSHIBA 32A3030D-01 lcd\... 27.06.2015
. 2 3
file://D:\Documents and Settings\Admin\ \TOSHIBA 32A3030D-01 lcd\... 27.06.2015
. 3 3
file://D:\Documents and Settings\Admin\ \TOSHIBA 32A3030D-01 lcd\... 27.06.2015
. 1 2
FUNCTION AND OPERATION
Digital Auto Tuning
Note: As new services are broadcast it will be necessary to re-tune the television in order to
view them.
Auto Tuning
file://D:\Documents and Settings\Admin\ \TOSHIBA 32A3030D-01 lcd\... 27.06.2015
. 2 2
file://D:\Documents and Settings\Admin\ \TOSHIBA 32A3030D-01 lcd\... 27.06.2015
. 1 3
FUNCTION AND OPERATION
Digital Programme Sorting, Manual Tuning
Note: When the television is switched off the mode being viewed at the time will
automatically be selected when the television is switched back on.
Programme Sorting
file://D:\Documents and Settings\Admin\ \TOSHIBA 32A3030D-01 lcd\... 27.06.2015
. 2 3
Manual Tuning
file://D:\Documents and Settings\Admin\ \TOSHIBA 32A3030D-01 lcd\... 27.06.2015
. 3 3
file://D:\Documents and Settings\Admin\ \TOSHIBA 32A3030D-01 lcd\... 27.06.2015
. 1 2
FUNCTION AND OPERATION
Tuning Analogue Mode for the First Time
The Quick Setup feature will tune all analogue channels currently available in the area. To
put the television into ATV mode press the button then use or to select ATV.
file://D:\Documents and Settings\Admin\ \TOSHIBA 32A3030D-01 lcd\... 27.06.2015
. 2 2
file://D:\Documents and Settings\Admin\ \TOSHIBA 32A3030D-01 lcd\... 27.06.2015
. 1 4
FUNCTION AND OPERATION
Analogue Manual Tune
The television can be tuned-in manually using Manual tuning. For example: if the television
cannot be connected to a media recorder/decoder with a SCART lead or to tune-in a station
on another System.
Use and to move across the screen and select any of these Manual Tune options.
Programme : The number to be pressed on the remote control.
System : Specific to certain areas.
Colour system : Factory set to Auto, should only be changed if problems are
experienced, i.e. NTSC input from external source.
Programme skip : means nothing has been stored or the facility to skip
the channel is ON.
Channel : The channel number on which a station is being broadcast.
Search : Search up and down for a signal.
Manual fine tuning : Only used if interference/weak signal is experienced.
Station : Station identification. Use the or and or buttons to
enter up to seven characters.
To allocate a programme position on the television for a decoder and media recorder: turn the
decoder on, insert a pre-recorded film in the media recorder and press PLAY, then manually
tune.
file://D:\Documents and Settings\Admin\ \TOSHIBA 32A3030D-01 lcd\... 27.06.2015
. 2 4
file://D:\Documents and Settings\Admin\ \TOSHIBA 32A3030D-01 lcd\... 27.06.2015
. 3 4
file://D:\Documents and Settings\Admin\ \TOSHIBA 32A3030D-01 lcd\... 27.06.2015
. 4 4
file://D:\Documents and Settings\Admin\ \TOSHIBA 32A3030D-01 lcd\... 27.06.2015
. 1 2
FUNCTION AND OPERATION
Auto Tune
Using Auto Tuning
file://D:\Documents and Settings\Admin\ \TOSHIBA 32A3030D-01 lcd\... 27.06.2015
. 2 2
file://D:\Documents and Settings\Admin\ \TOSHIBA 32A3030D-01 lcd\... 27.06.2015
Handling the LCD Module . 1 4
SAFETY INSTRUCTION
Handling the LCD Module
Safety Precaution
In the event that the screen is damaged or the liquid crystal (fluid) leaks, do not breathe in or
drink this fluid.
Also, never touch this fluid. Such actions could cause toxicity or skin irritation. If this fluid
should enter the mouth, rinse the mouth thoroughly with water. If the fluid should contact the
skin or clothing, wipe off with alcohol, etc., and rinse thoroughly with water. If the fluid
should enter the eyes, immediately rinse the eyes thoroughly with running water.
Precautions for Handling the LCD Module
CAUTION: The metal edges of the LCD module are sharp, handle it with
care.
The LCD module can easily be damaged during disassembly or reassembly; therefore,
always observe the following precautions when handling the module.
1. When attaching the LCD module to the LCD cover, position it appropriately and fasten
at the position where the display can be viewed most conveniently.
2. Carefully align the holes at all four corners of the LCD module with the corresponding
holes in the LCD cover and fasten with screws. Do not strongly push on the module
because any impact can adversely affect the performance. Also use caution when
handling the polarized screen because it can easily be damaged.
file://D:\Documents and Settings\Admin\ \TOSHIBA 32A3030D-01 lcd\... 27.06.2015
Handling the LCD Module . 2 4
3. If the panel surface becomes soiled, wipe with cotton or a soft cloth. If this does not
remove the soiling, breathe on the surface and then wipe again.
If the panel surface is extremely solied, use a CRT cleaner as a cleaner. Wipe off the
panel surface by drop the cleaner on the cloth. Do not drop the cleaner on the panel.
Pay attention not to scratch the panel surface.
4. Leaving water or other fluids on the panel screen for an extended period of time can
result in discoloration or stripes. Immediately remove any type of fluid from the screen.
5. Glass is used in the panel, so do not drop or strike with hard objects. Such actions can
damage the panel.
file://D:\Documents and Settings\Admin\ \TOSHIBA 32A3030D-01 lcd\... 27.06.2015
Handling the LCD Module . 3 4
6. CMOS-LSI circuitry is used in the LCD module, so avoid damage due to static
electricity. When handling the module, use a wrist ground or anchor ground.
7. Do not expose the LCD module to direct sunlight or strong ultraviolet rays for an
extended period of time.
8. Do not store the LCD module below the temperature conditions described in the
specifications. Failure to do so could result in freezing of the liquid crystal due to cold
air or loss of resilience or other damage.
9. Do not disassemble the LCD module. Such actions could result in improper operation.
file://D:\Documents and Settings\Admin\ \TOSHIBA 32A3030D-01 lcd\... 27.06.2015
Handling the LCD Module . 4 4
10. When transporting the LCD module, do not use packing containing epoxy resin
(amine) or silicon resin (alcohol or oxim). The gas generated by these materials can
cause loss of polarity.
file://D:\Documents and Settings\Admin\ \TOSHIBA 32A3030D-01 lcd\... 27.06.2015
. 1 2
PANEL IDENTIFICATION
Panel Identification
If the several panels are alternatively used in the same model without amending the model
name, the identification marking will be shown at the last digit of the set serial number on the
specification label on the back cover.
In servicing, do not alter the panel because several setting and parts are different.
Marking Panel Vendor Marking Panel Vendor Marking Panel Vendor
A AUO J S SHARP
B K SAMSUNG T
C CMO L LPL U
D M V
E N W
F P X
G Q Y
H IPS R Z
With this alternative use, some of key parts may differ and their combinations are
indicated with the suffix marking on the location number in the part list
(Miscellaneous).
e.g.
Location No. Part No. Description
B001A 75007869 LCD Panel, 32" LPL
B001B 75007870 LCD Panel, 32" AUO
MZ01A 75006036 LDVS Cable
MZ01B 75007893 LDVS Cable
file://D:\Documents and Settings\Admin\ \TOSHIBA 32A3030D-01 lcd\... 27.06.2015
. 2 2
file://D:\Documents and Settings\Admin\ \TOSHIBA 32A3030D-01 lcd\... 27.06.2015
U02A
U03B
LOW-B
Key
U01A
POWER
U04A
U03A
Main
Front-AV U05A
Digital
U03C
LED
. 1 4
SAFETY INSTRUCTION
WARNING: BEFORE SERVICING THIS CHASSIS, READ THE "SAFETY
PRECAUTION" AND "PRODUCT SAFETY NOTICE" INSTRUCTIONS BELOW.
Safety Precaution
WARNING: SERVICING SHOULD NOT BE ATTEMPTED BY ANYONE
UNFAMILIAR WITH THE NECESSARY PRECAUTIONS ON THIS RECEIVER.
THE FOLLOWING ARE THE NECESSARY PRECAUTIONS TO BE OBSERVED
BEFORE SERVICING THIS CHASSIS.
1. An isolation transformer should be connected in the power line between the receiver
and the AC line before any service is performed on the receiver.
2. Always disconnect the power plug before any disassembling of the product. It may
result in electrical shock.
3. When replacing a chassis in the cabinet, always be certain that all the protective
devices are put back in place, such as nonmetallic control knobs, insulating covers,
shields, isolation resistor-capacitor network, etc.
4. Always keep tools, components of the product, etc away from the children, These items
may cause injury to children.
5. Depending on the model, use an isolation transformer or wear suitable gloves when
servicing with the power on, and disconnect the power plug to avoid electrical shock
when replacing parts. In some cases, alternating current is also impressed in the
chassis, so electrical shock is possible if the chassis is contacted with the power on.
6. Always use the replacement parts specified for the particular model when making
repairs. The parts used in products require special safety characteristics such as
file://D:\Documents and Settings\Admin\ \TOSHIBA 32A3030D-01 lcd\... 27.06.2015
. 2 4
inflammability, voltage resistance, etc. therefore, use only replacement parts that have
these same characteristics. Use only the specified parts when the mark is indicated
in the circuit diagram or parts list.
7. Parts mounting and routing dressing of wirings should be the same as that used
originally. For safety purposes, insulating materials such as isolation tube or tape are
sometimes used and printed circuit boards are sometimes mounted floating. Also make
sure that wirings is routed and clamped to avoid parts that generate heat and which use
high voltage. Always follow the manufactured wiring routes / dressings.
8. Always ensure that all internal wirings are in accordance before re-assembling the
external casing after a repairing completed. Do not allow internal wiring to be pinched
by cabinets, panels, etc. Any error in reassembly or wiring can result in electrical
leakage, flame, etc., and may be hazardous.
9. NEVER remodel the product in any way. Remodeling can result in improper operation,
malfunction, or electrical leakage and flame, which may be hazardous.
10. Touch current check. (After completing the work, measure touch current to prevent an
electric shock.)
Plug the AC cord directly into the AC outlet. Do NOT use an isolation transformer
for this check.
Connect a measuring network for touch currents between each exposed metallic part
on the set and a good earth ground such as a water pipe.
Annex D
(normative)
Measuring network for TOUCH CURRENTS
file://D:\Documents and Settings\Admin\ \TOSHIBA 32A3030D-01 lcd\... 27.06.2015
. 3 4
Resistance values in orms ( ).
V: Voltmeter or oscilloscope
(r.m.s. or peak reading)
Input resistance : 1M
Input capacitance : 200 pF
Frequency range : 15 Hz to 1 MHz and d.c. respectively
Note: Appropriate measures should be taken to obtain the correct value in case of non
sinusoidal waveforms.
The measuring instrument is calibrated by comparing the frequency factor of with the
solid line in figure F.2 of IEC 60990 at various frequencies. A calibration curve is
constructed showing the deviation of from the ideal curve as a function of frequency.
TOUCH CURRENT = /500 (peak value).
The potential at any point (TOUCH CURRENT) expressed as voltage and
does not exceed the following value:
The part or contact of a TERMINAL is not HAZARDOUS LIVE if:
a) The open-circuit voltage should not exceed 35 V (peak) a.c. or 60 V d.c. or, if a) is not
met.
b) The measurement of the TOUCH CURRENT shall be carried out in accordance with
IEC 60990, with the measuring network described in Annex D of this standard.
The TOUCH CURRENT expressed as voltages and , does not exceed the
following values:
- for a.c. : = 35 V (peak) and = 0.35 V (peak);
- for d.c. : = 1.0 V
Note: The limit values of = 0.35 V (peak) for a.c. and = 1.0 V for d.c. correspond to
the values 0.7 mA (peak) a.c. and 2.0 mA d.c.
file://D:\Documents and Settings\Admin\ \TOSHIBA 32A3030D-01 lcd\... 27.06.2015
. 4 4
Product Safety Notice
Many electrical and mechanical parts in this chassis have special safety-related
characteristics. These characteristics are often passed unnoticed by a visual inspection and
the protection afforded by them cannot necessarily be obtained by using replacement
components rated for higher voltage, wattage, etc. Replacement parts which have these
special safety characteristics are identified in this manual and its supplements; electrical
components having such features are identified by the international hazard symbols on the
schematic diagram and the parts list.
Before replacing any of these components, read the parts list in this manual carefully. The
use of substitute replacement parts which do not have the same safety characteristics as
specified in the parts list may create electrical shock, fire, or other hazards.
file://D:\Documents and Settings\Admin\ \TOSHIBA 32A3030D-01 lcd\... 27.06.2015
. 1 2
SPECIFICATION
file://D:\Documents and Settings\Admin\ \TOSHIBA 32A3030D-01 lcd\... 27.06.2015
. 2 2
file://D:\Documents and Settings\Admin\ \TOSHIBA 32A3030D-01 lcd\... 27.06.2015
Digital BOARD P212B
(A3030D ONLY) Audio OUT
CVBS
PJ212 CVBS OUT
IC302
Serial port Audio Amp
for debug ITU-R656 P200B
H801 PJ400 Digital VIDEO OUT
+Low B AC INPUT& Tuner DVB-CI