Text preview for : RT-13LA60 Service Manual.pdf part of LG RT-13LA60 Service Manual LG LCD RT-13LA60 Service Manual.pdf
Back to : RT-13LA60 Service Manual. | Home
website:http://biz.LGservice.com
e-mail:http://www.LGEservice.com/techsup.html
LCD TV
SERVICE MANUAL
CHASSIS : ML-024J
MODEL : RT-13LA60
CAUTION
BEFORE SERVICING THE CHASSIS,
READ THE SAFETY PRECAUTIONS IN THIS MANUAL.
CONTENTS
CONTENTS .............................................................................................. 2
PRODUCT SAFETY ..................................................................................3
DESCRIPTION OF CONTROLS .............................................................. 4
ADJUSTMENT INSTRUCTION .................................................................7
TROUBLE SHOOTING ............................................................................12
BLOCK DIAGRAM...................................................................................13
EXPLODED VIEW .................................................................................. 15
EXPLODED VIEW PARTS LIST ..............................................................16
REPLACEMENT PARTS LIST ............................................................... 17
SVC. Sheet .................................................................................................
- 2 -
PRODUCT SAFETY
IMPORTANT SAFETY NOTICE 1. Immediately before handling any semiconductor component or
This manual was prepared for use only by properly trained audiovisual service semiconductor-equipped assembly, drain off any electrostatic charge on the
technicians. When servicing this product, under no circumstances should the body by touching a known earth ground. Alternatively, obtain and wear a
original design be modified or altered without permission from LG Electronics commercially available discharging wrist strap device, which should be
Inc. All components should be replaced only with types identical to those in the removed for potential shock reasons prior to applying power to the unit under
original circuit and their physical location, wiring, and lead dress must conform test.
to original layout upon completion of repairs. If any fuse (or Fusible Resistor) in 2. After removing an electrical assembly equipped with ES devices, place the
this TV receiver is blown, replace it only with the factory specified fuse type and assembly on a conductive surface such as an ESD mat, to prevent
rating. When replacing a high wattage resistor (Oxide Metal Film Resistor, over electrostatic charge buildup or exposure of the assembly.
1W), keep the resistor 10mm away from PCB. Always keep wires away from 3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.
high voltage or high temperature parts. 4. Use only an anti-static solder removal device. Some solder removal devices
not classified as "anti-static" can generate electrical charges sufficient to
Special components are also used to prevent shock and fire hazard. damage ES devices.
These components are indicated by the letter "x" included in their component 5. Do not use freon-propelled chemicals. These can generate electrical charge
designators and are required to maintain safe performance. No deviations are sufficient to damage ES devices.
allowed without prior approval by LG Electronis Inc. Service work should be 6. Do not remove a replacement ES device from its protective package until
performed only after you are thoroughly familiar with these safety checks and immediately before you are ready to install it. (Most replacement ES devices
servicing guidelines. are packaged with leads electrically shorted together by conductive foam,
aluminum foil, or comparable conductive material.)
Circuit diagrams may occasionally differ from the actual circuit used. 7. Immediately before removing the protective material from the leads of a
This way, implementation of the latest safety and performance improvement replacement ES device, touch the protective material to the chassis or circuit
changes into the set is not delayed until the new service literature is printed. assembly into which the device will be installed.
CAUTION: Do not attempt to modify this product in any way. Caution: Be sure no power is applied to the chassis or circuit, and observe
Never perform customized installations without manufacturer's all other safety precautions.
approval.
Unauthorized modifications will not only void the warranty, but may 8. Minimize bodily motions when handling unpackaged replacement ES
lead to property damage or user injury. devices. (Otherwise, seemingly harmless motion, such as the brushing
together of your clothing or the lifting of your foot from a carpeted floor, can
generate static electricity sufficient to damage an ES device.)
GENERAL GUIDANCE
An lsolation Transformer should always be used during the servicing
of a receiver whose chassis is not isolated from the AC power line. Use a
transformer of adequate power rating to protect against personal injury from
electrical shocks. It will also protect the receiver and its components from being
damaged by accidental shorts of the circuitry that may be inadvertently
introduced during the service operation.
Before returning the receiver to the customer, always perform an AC leakage
current check on the exposed metallic parts of the cabinet, such as antennas,
terminals, etc., to be sure the set is safe to operate
without damage of electrical shock.
LEAKAGE CURRENT COLD CHECK
(ANTENNA COLD CHECK)
With the instrument's AC plug removed from AC source, connect an electrical
jumper across the two AC plug prongs. Place the AC switch in the on position,
connect one lead of ohm-meter to the AC plug prongs tied together, and touch
other ohm-meter lead in turn to each exposed metallic parts such as antenna
terminals, phone jacks, etc. If the exposed metallic part has a return path to the
chassis, the measured resistance should be between 1M and 5.2M. When
the exposed metal has no return path to the chassis the reading must be
infinite. Any other abnormality that exists must be corrected before
the receiver is returned to the customer.
ELECTROSTATICALLY SENSITIVE DEVICES
Some semiconductor (solid-state) devices can be damaged easily by static
electricity. Such components commonly are called Electrostatically Sensitive
(ES) Devices. Examples of typical ES devices are integrated circuits and some
field-effect transistors and semiconductor "chip" components. The following
techniques should be used to help reduce the incidence of component damage
caused by static electricity.
- 3 -
DESCRIPTION OF CONTROLS
All the functions can be controlled with the remote control handset.
Some functions can also be adjusted with the buttons on the side
panel of the set.
Remote control handset
Before you use the remote control handset, please install the bat-
MUTE POWER teries. See the next page.
1 9
TV/AV I/II 1. MUTE
2 10 switches the sound on or off.
LIST Q.VIEW MENU
3 11 2. TV/AV
4 selects TV or AV mode.
clears the menu from the screen.
PR switches the set on from standby.
5 OK
VOL VOL 3. LIST
PR displays the programme table.
4. Q.VIEW
1 2 3 returns to the previously viewed programme.
selects a favourite programme.
6 4 5 6
5. D / E (Programme Up/Down)
7 8 9
selects a programme or a menu item.
switches the set on from standby.
F / G (Volume Up/Down)
7 SSM 0 PSM 12
adjusts the volume.
SLEEP TEXT adjusts menu settings.
8 OK
UPDATE TIME accepts your selection or displays the current mode.
SIZE MIX 13 6. NUMBER BUTTONS
HOLD REVEAL
switches the set on from standby and selects a programme.
?
INDEX MODE 7. SSM (Sound Status Memory)
i M recalls your preferred sound setting.
8. SLEEP
sets the sleep timer.
- 4 -
9. POWER
switches the set on from standby or off to standby.
10. I/II
selects the language during dual language broadcast.
selects the sound output (option).
11. MENU
selects a menu. MUTE POWER
1 9
12. PSM (Picture Status Memory) TV/AV I/II
recalls your preferred picture setting. 2 10
LIST Q.VIEW MENU
13. TELETEXT BUTTONS (option) 3 11
These buttons are used for teletext. 4
For further details, see the `Teletext' section.
PR
: No function
* 5 VOL
OK
VOL
COLOURED BUTTONS
PR
These buttons are used for teletext (only TELETEXT models) or
programme edit.
1 2 3
Battery installation
6 4 5 6
The remote control handset is pow- 7 8 9
ered by two AAA/Alkaline type bat-
teries. To load the batteries, turn 7 SSM 0 PSM 12
the remote control handset over
and open the battery compartment. SLEEP TEXT
Install two batteries as indicated by 8
the polarity symbols ( + and - ) UPDATE TIME
marked inside the compartment.
SIZE MIX 13
HOLD REVEAL
?
INDEX MODE
Note : To avoid damage from possible battery leakage, remove the i M
batteries if you do not plan to use the remote control handset for an
extended period of time.
- 5 -
Side panel
PR
6
VOL
5
OK 4 9 10
MENU 3
TV
AV 2
7 H/P S-VIDEO VIDEO (MONO) L
AV2
AUDIO R
/I
ON/OFF 1
8
Back panel
1. ON/OFF ( r /I) 7. POWER/STANDBY INDICATOR (r ) r
switches the set on from standby or off to illuminates red in standby mode.
standby. illuminates green when the set is switched on.
Note : Power line lives even when the power
is off. 8. REMOTE CONTROL SENSOR
2. TV/AV 9. HEADPHONE SOCKET
selects TV or AV mode. Connect the headphone plug to this socket.
clears the menu from the screen.
switches the set on from standby. 10. AUDIO/VIDEO IN SOCKETS (AV2)
Connect the audio/video out sockets of exter-
3. MENU nal equipment to these sockets.
selects a menu. S-VIDEO/AUDIO IN SOCKETS (SAV)
Connect the video out socket of an S-VIDEO
4. OK VCR to the S-VIDEO socket.
accepts your selection or displays the current Connects the audio out sockets of the S-
mode. VIDEO VCR to the audio sockets as in AV2.
5. F / G (Volume Up/Down)
adjusts the volume.
adjusts menu settings.
6. D / E (Programme Up/Down)
selects a programme or a menu item.
switches the set on from standby.
- 6 -
ADJUSTMENT INSTRUCTION
1. Application Object (3) The set must be operated for 15 minutes preliminarily
This instruction is for the application to the LCD TV. before adjustment if there is no specific designation.
[ `Heat Run' must be performed with the full white signal or TV
noise signal in the internal part of the set.
2. Notes [ The time for `Heat Run' can be changed owing to production
plan.
(1) The adjustment must be performed under the correct [ Line Test condition (TV): standard color signal 65