Text preview for : 070-3771-00_68000_Emulator_Processor_Inst_Feb82.pdf part of Tektronix 070-3771-00 68000 Emulator Processor Inst Feb82 Tektronix 85xx 8540 070-3771-00_68000_Emulator_Processor_Inst_Feb82.pdf
Back to : 070-3771-00_68000_Emulato | Home
Tektron~ COMMITTED TO EXCELLENCE
WARNING
THE FOLLOWING SERVICING INSTRUCTIONS
ARE FOR USE BY QUALIFIED PERSONNEL ONLY.
TO AVOID PERSONAL INJURY, DO NOT
PERFORM ANY SERVICING OTHER THAN THAT
CONTAINED IN OPERATING INSTRUCTIONS
UNLESS YOU ARE QUALIFIED TO DO SO.
PLEASE CHECK FOR CHANGE INFORMATION
AT THE REAR OF THIS MANUAL.
rhis manual supports the following
rEKTRONIX products:
8550 8540
Option Option Products
2P 2P 8300E26
3U 3U 8300P26
8300P26 option 01
Tektronix, Inc.
P.O. Box 500
Beaverton, Oregon 97077 Serial Number - - - - - -_ _
070-3771-00
Product Group 61 First Printing FEB 1982
68000 E. P. Installation Service
PREFACE
ABOUT THIS MANUAL
This manual tells how to install the 68000 Emulator Processor module and its
Prototype Control Probe in a TEKTRONIX 8550 Microcomputer Development Lab or
8540 Integration Unit. This manual also contains performance verification
information.
The TEKTRONIX 68000 Emulator Processor module utilizes a Motorola MC68000
microprocessor to perform the emulation function. All references in this
manual to the 68000 microprocessor pertain to the Motorola MC68000
microprocessor.
Throughout this manual, the term "microcomputer development system" (or
simply "development system") is used to refer to the TEKTRONIX 8550
Microcomputer Development Lab or 8540 Integration Unit.
For user information about the 68000 Emulator Processor, refer to the
appropriate System Users' Manual and its 68000 Emulator Specifics supplement.
Service information about the 68000 Emulator Processor is provided in the
optional 68000 Emulator Processor and Prototype Control Probe Service Manual.
MANUAL ORGANIZATION
This manual is divided into four sections:
Section 1 contains general information about the Emulator Processor module
and the Prototype Control Probe.
Section 2 contains information about configuration jumpers.
Section 3 provides detailed installation procedures for the Emulator
Processor module and the Prototype Control Probe.
Section 4 describes procedures used to verify proper functional performance
of the Emulator Processor module and the Prototype Control Probe.
@ i
Preface - 68000 E. P. Installation Service
GENERAL INFORMATION
REVISION HISTORY
As this manual is revised and reprinted, revision history information is
included on the text and diagram pages. Original manual pages are identified
with an '@' symbol at the bottom inside corner of the page. When existing
pages are revised, the '@' symbol is replaced with a revision date
(REV OCT 1981). New pages added to a section, whether they contain old, new,
or revised information, will be identified with the '@' symbol and a date
(@ OCT 1981).
CHANGE INFORMATION
Change notices are issued by Tektronix, Inc., to document changes in the
manual after it has been published. Change information is located in the
back of this manual, following the yellow tab marked "CHANGE INFORMATION".
When you receive this manual, enter any change information into the body of
the manual, as indicated on the change notice.
ii
68000 E.P. Installation Service
CONTENTS
SAFETY SUMMARY
Page
Operators .............................................................. vii
Servicing .............................................................. ix
Section GENERAL INFORMATION
Introduction ........................................................... 1-1
Modes of Operation 1-1
Emulator Processor Module .............................................. 1-2
Prototype Control Probe 1-4
Specifications 1-4
Electrical Characteristics