Text preview for : Alignment & Adjustment.pdf part of Samsung Alignment & Adjustment Samsung LCD TV LE32-37-40S62B LE32-37-40S62B_ch_gsa32-37-40heu Alignment & Adjustment.pdf
Back to : Alignment & Adjustment.pd | Home
3 Alignments and Adjustments
3 Alignments and Adjustments
3-1 Service Instruction
1. Usually, a color TV-VCR needs only slight touch-up adjustment upon installation.
Check the basic characteristics such as height, horizontal and vertical sync.
2. Use the specified test equipment or its equivalent.
3. Correct impedance matching is essential.
4. Avoid overload. Excessive signal from a sweep generator might overload the front-end
of the TV. When inserting signal markers, do not allow the marker generator to distort
test result.
5. Connect the TV only to an AC power source with voltage and frequency as specified on
the backcover nameplate.
6. Do not attempt to connect or disconnect any wire while the TV is turned on. Make sure
that the power cord is disconnected before replacing any parts.
7. To protect aganist shock hazard, use an isolation transform.
3-1
3 Alignments and Adjustments
3-2 How to Access Service Mode
3-2-1 Entering Factory Mode
1. To enter "Service Mode" Press the remote -control keys in this sequence :
- If you do not have Factory remote - control
Power OFF INFO MENU MUTE Power ON
- If you have Factory remote - control
PICTURE ON DISPLAY FACTORY
- The buttons are active in the service mode.
1. Remote - Control Key : Power, Arrow Up, Arrow Down, Arrow Left
Arrow Right, Menu, Enter, Number Key(0~9)
2. Function - Control Key : Power, CH +, CH -, VOL +, VOL -,
Menu, TV/VIDEO(Enter)
3-2-2 Panel Check
Specially for LE32,37,40S62*, You have to check Panel Maker Because of different adjustments as
follows. First of all, Check the label rating!
1) Label Rating File
PANEL MAKER
If Panel Mark is "C", Set the factory mode Panel BOM(Bill of material) : BN07-00424A
indicating as follows.(LE32S62BX/**) Connector between Panel and Power Unit
: BN39-00712J (400mm)
Panel BOM(Bill of material) : BN07-00425A * Option Byte
Connector between Panel and Power Unit 1. Panel Vender : CPT
: BN39-00712C (300mm) 2. Dimming : ANA-P3
3. Gamma : S4
* Option Byte If Panel Mark is "A" , Set the Factory mode
1. Panel Vender : CPT indicating as follows. (LE40S62BX/**)
2. Dimming : ANA-P3 Panel BOM(Bill of Material) : BN07-00370A
3. Gamma : OFF Connecotor between Panel and Powe Unit :
BN39-00712E (400mm)
If Panel Mark is "C". * Option Byte
Set the factory mode indicating as follows. 1. Panel Vender : AUO
(LE37S62BX/**) 2. Dimming : ANA-P3
3. Gamma : OFF
Others are same shown below.
3-2
3 Alignments and Adjustments
3-3 Factory Data (MTK)
1. Calibration
2. Option Byte XX XX XX XX
3. W/B
4. W/B Movie
5. MTK8202
6. Sound
7. YC Delay
8. Adjust
9. Bus Stop
10. Password 80 80 80 80
11. Checksum 0000
12. Spread Spectrum
13. Reset
T_SNMMPEU-1000 (Main Micom Ver) Month/ Day / Year / Hour/ Min./Sec.
Panel On Time(Hour) XXXXX
0 0
1. Calibration
1) AV Calibration ------ Failure../Success.. ------- Master(MSPG-925F) : model #2, Pattern #24
2) DTV Calibration ----- Failure../Success.. ------- Master(MSPG-925F) : model #6, Pattern #24
3) PC Calibration ------ Failure../Success.. ------- Master(MSPG-925F) : model #21, Pattern #24
4) HDMI Calibration ---- Failure../Success.. ------- Master(MSPG-925F) : model #6, Pattern #24
2. Option Byte
Panel Inch 32 V-Chip Off
Panel Vender CPT Caption Off
Dimming ANA-P3 ID TV Mode Off
Gamma Off ID TV Country UK
Auto Power On Memory Type ETRON
Hotel Mode Off Volume Table Small
Shop Mode Off
Auto FM Off
High Devi Off
Carrier Mute Off
TTX On
TTX List Flof
TTX Group User OSD
3. White Balance
ITEM RF/AV(Initial value) Component(Initial value) PC HDMI(Initial value)
SubBright 128 128 138 (Fixed value) 128
Roffset 128 128 128 (Fixed value) 128
Goffset 128 128 128 (Fixed value) 128
Boffset 128 128 128 (Fixed value) 128
SubContrast 131 128 115 (Fixed value) 128
RGain 128 128 128 (Fixed value) 128
GGain 128 128 128 (Fixed value) 128
BGain 128 128 128 (Fixed value) 128
3-3
3 Alignments and Adjustments
4. W/B Movie
Service P Mode Dynamic Cool1 Blue Offset 128
Service Color Tone Cool1 Normal Red Gain 134
Mov. Contrast 80 Normal Blue Gain 121
Mov. Brightness 50 Normal Red Offset 127
Mov. Color 25 Normal Blue Offset 126
Mov. Sharpness 45 Warm1 Red Gain 143
Cool2 Red Gain 128 Warm1 Blue Gain 111
Cool2 Blue Gain 134 Warm1 Red Offset 128
Cool2 Red Offset 128 Warm1 Blue Offset 127
Cool2 Blue Offset 128 Warm2 Red Gain 142
Cool1 Red Gain 128 Warm2 Blue Gain 101
Cool1 Blue Gain 128 Warm2Red Offset 127
Cool1 Red Offset 128 Warm2 Blue Offset 128
5. MTK8202
1) Cal. Adjustment
R_Offset 41 CVBS Gain 50
G_Offset 23 CVBS U 0
B_Offset 28 CVBS V 0
R_Gain 92 HDMI R_Gain Ref. 229
G_Gain 96 HDMI G_Gain Ref. 229
B_Gain 92 HDMI B_Gain Ref. 229
Y_Offset 23 HDMI R_Offset Ref. 16
Cb_Offset 28 HDMI G_Offset Ref. 16
Cr_Offset 31 HDMI B_Offset Ref. 16
Y_Gain 43 LVDS control 55
Cb_Gain 43
Cr_Gain 43
CVBS Offset 50
2) Cal. Target
AV_offset Target 15 PC_G_Offset Target 1
AV_offset Delta 1 PC_B_Offset Target 1
AV_Gain Target 220 PC_R_Offset Delta 0
AV_Gain Delta 2 PC_G_Offset Delta 0
Component_Y_Gain Target 234 PC_B_Offset Delta 0
Component_Y_Gain Delta 2 PC_R_Gain Target 254
Component_Y_Offset Target 15 PC_G_Gain Target 254
Component_Pb_Offset Target 128 PC_B_Gain Target 254
Component_Pr_Offset Target 127 PC_R_Gain Delta 0
Component_Y_Offset Delta 1 PC_G_Gain Delta 0
Component_Pb_Offset Delta 0 PC_B_Gain Delta 0
Component_Pr_Offset Delta 0
PC_R_Offset Target 1
3-4
3 Alignments and Adjustments
3) Scart RGB
SC1_R_Offset 112
SC1_G_Offset 112
SC1_B_Offset 112
SC1_R_Gain 80
SC1_G_Gain 80
SC1_B_Gain 80
4) Picture Enhance
Cut Off 2
Upper 29
Center L Lmt 8
Center R Lmt 24
Ugain Max 40
Lgain Max 40
6. Sound
AM Mute Off Num of Double Chk 30
AM_mute Th_High 176 Mono Weight 1
AM_mute Th_Low 144 Stereo Weight 1
FM_mute Th_High 34 Dual Weight 1
FM_mute Th_Low 32 M2S Threshold 10
Carrier Shift Off S2M Threshold 10
Saturation Mute Off NICAM FINE VOL 20
Correct Threshold 6 FM FINE VOL 20
Sync Loop 201 AM FINE VOL 20
Error Threshold 8 FINE TUNE VOL 20
Parity Error Thrd 48
Every Num Frames 512
Num of Check 10
7. YC Delay
RF PAL-B/G 10 AV NTSC4.43 10
RF PAL-D/K 10 AV PAL60 10
RF PAL- I 10
RF PAL- L/L' 10
RF SECAM-B/G 10
RF SECAM-D/K 10
RF SECAM-I 10
RF SECAM-L/L' 10
RF NTSC3.58 10
RF NTSC4.43 10
AV PAL 10
AV SECAM 10
AV NTSC 3.58 10
3-5
3 Alignments and Adjustments
8. Adjust
1) User Control Initial
TTX PWM 25 N_Dyn.Contrast Off
Dyn. Contrast 100 Dynamic CE Off
Dyn. Brightness 45 Dynamic Dimming Off
Dyn. Color 55 Channel Table Suwon
Dyn. Sharpness 75 Video Mute Time 5
Std. Contrast 80 Language English
Std. Brightness 50
Std. Color 55
Std. Sharpness 50
Melody Volume 10
Sub Color 50
Contrast Gain 64
Dynamic Contrast Off
2) LNA PLUS
RF_Db-1 0
RF_Db-2 0
RF_Db-3 0
3) Hotel Option
Power On Channel 1
Power On Band 0
Power On Volume 10
Max Volume 100
Local Key Lock OFF
Power On Source Auto
4) HDCP Write
9. Bus Stop
Main Loop Off
Eeprom Off
Tuner Off
Normal Off
Watch Dog On
10. Password : 80 80 80 80
3-6
3 Alignments and Adjustments
11. Checksum XXXX
12. Spread Spectrum
Spread Spectrum On Step_1024_768 90
Step_480I/576I 90 Range_1024_768 43
Range_480I/576I 32 Step_1360_768 90
Step_480P/576P 112 Range_1360_768 43
Range_480P/576P 41
Step_720P 90
Range_720P 32
Step_1080I 90
Range_1080I 32
Step_640_480 90
Range_640_480 43
Step_800_600 90
Range_800_600 43
13. Reset
3-7
3 Alignments and Adjustments
3-4 Service Adjustment
3-4-1 White Balance - Calibration
If picture color is wrong, do calibration first.
Equipment : CA210, Patten : chess pattern
Execute calibration in Factory Mode
Source AV : PAL composite, Component : 1280*720/60Hz
PC : 1024*768/60Hz
( chess patten )
3-4-2 White Balance - Adjustment
If picture color is wrong, check White Balance condition.
Equipment : CA210, Patten : Toshiba
Adjust W/B in Factory Mode
Sub brightness and R/G/B Offset controls low light region
Sub contrast and R/G/B Gain controls high light region
Source AV : PAL composite, Component : 1280*720/60Hz
HDMI[DVI] : 1280*720/60Hz
[ Test Pattern : MSPG-945 Series Pattern #16 ]
*Color temperature
1500K +/-500, -6 ~-20 MPCD
*Color coordinate
H/L : 267/263 +/- 2 35.0 Ft +/- 2.0Ft
L/L : 270/260 +/- 3 1.5 Ft +/- 0.2Ft
Toshiba Patten
3-8
3 Alignments and Adjustments
3-4-3 Conditions for Measurement
1. On the basis of toshiba ABL pattern : High Light level (57 IRE)
- INPUT SIGNAL GENERATOR : MSPG-925LTH
* Mode NO 2 : 744X484@60 Hz
NO 6 : 1280X720@60 Hz
NO 21 : 1024X768@60 Hz
* Pattern NO 36 : 16 Color Pattern
NO 16 : Toshiba ABL Pattern
2. Optical measuring device : CA210 (FL)
Please use the MSPG-925 LTH generator for model LE32S62B, LE37S62B, LE40S62B.
3-4-4 Method of Adjustment
1. Adjust the white balance of AV, Component and DVI Modes.
(AV Component)
a) Set the input to the mode in which the adjustment will be made
(RF DTV PC DVI).
* Input signal - VIDEO Mode : Model #2 (744*484 Mode), Pattern #16
- DTV,DVI Mode : Model #6 (1280*720 Mode), Pattern #16
- HDMI Mode: Model #6(1280*720 Mode), Pattern #16
b) Enter factory color control, confirm the data.
c) Adjust the low light. (Refer to table 1, 2 in adjustment position by mode)
- Adjust sub - Brightness to set the 'Y' value.
- Adjust red offset ('x') and blue offset ('y') to the color coordinates.
Picture 4-2 Toshiba ABL Pattern
Low light
Measurement point
* Do not adjust green offset data.
d) Adjust the high light. (Refer to table 1, 2 in adjustment position by mode)
- Adjust red gain ('x') and blue gain ('y') to the color coordinates.
* Do not adjust the green gain and sub-contrast (Y) data.
3-9
3 Alignments and Adjustments
d) Adjust the high light. (Refer to table 1, 2 in adjustment position by mode)
- Adjust red gain ('x') and blue gain ('y') to the color coordinates.
* Do not adjust the green gain and sub-contrast (Y) data.
Picture 4-3 Toshiba ABL Pattern
High light
Measurement point
3-5 Software Upgrade
3-5-1 How to Update Flash ROM
1. Installthe Flash Downloader
ConnectSet(Service Jack)and Jig Cable to execute Program Update.
3-10
3 Alignments and Adjustments
2. Flash Downloader program update (MTK)
- After Turning on the set, Click '1'(reset button)button two or more.
- Click 'Browse' button, and find micom file for update.
- Click 'Upgrade' button.
- Turn on the set.
3-11
3 Alignments and Adjustments
Memo
3-12