Text preview for : satellite te2000.pdf part of TOSHIBA satellite te2000 TOSHIBA Laptop satellite te2000.pdf
Back to : satellite te2000.pdf | Home
FIELD REPLACEABLE UNIT DOCUMENTATION
TM
Satellite
TE2000
GENERAL INFORMATION
Tools Required for Proper
Disassembly and Reassembly:
1. Phillips Screwdriver (Size 0&1)
2. Flat head Screwdriver
3. Security Torx (Size 7)
4. Case Separator
5. ESD Wrist Strap
6. ESD mat
7. Tweezers
Before attempting any of the following procedures,
make sure that the main battery and AC adaptor is
not connected to the unit and the environment in
which you are working on is protected from
Electro-Static Discharge(ESD).
TOSHIBA
Tough Enough for Today's World.
Download service manual and resetter printer at http://printer1.blogspot.com
FIELD REPLACEABLE UNIT DOCUMENTATION
TM
Satellite
TE2000
TABLE OF CONTENTS:
1. BATTERY PACK REMOVAL
2. OPTIONAL PC CARD REMOVAL
3. SELECT BAY REMOVAL
4. CD-R/DVD-ROM DRIVE DISASSEMBLY
5. MEMORY MODULE REMOVAL
6. MODEM BOARD REMOVAL
7. HDD REMOVAL
8. KEYBOARD REMOVAL
9. WIRELESS LAN CARD REMOVAL
10. TOP COVER REMOVAL
11. COOLING MODULE REMOVAL
12. CPU REMOVAL
13. RTC BATTERY REMOVAL
14. POWER SUPPLY BOARD REMOVAL
15. SOUND BOARD REMOVAL
16. SYSTEM BOARD REMOVAL
17. MEMBRANE SWITCH REMOVAL
18. SPEAKERS REMOVAL
19. 14.1'' DISPLAY MASK REMOVAL
20. FL INVERTER AND 14.1'' LCD REMOVAL
TOSHIBA
Tough Enough for Today's World.
Download service manual and resetter printer at http://printer1.blogspot.com
FIELD REPLACEABLE UNIT DOCUMENTATION
TM
Satellite
TE2000
BATTERY PACK REMOVAL OPTIONAL PC CARD REMOVAL
Battery
Lock
Release
lever
Battery
Pack
PC card
Eject button
1. Turn the computer upside down as shown. 1. Press the eject button of the PCCard you want to
2. Slide the battery lock to unlock position. remove.
3. Slide battery release lever in the direction of the 2. Press the extended eject button to pop the PC card
arrow. out.
3. Lift out the battery. 3. Grasp the PC card and remove it.
Note: Before removing any PC Card device, make
sure it is "STOPPED" in the PC Card manager.
SELECT BAY REMOVAL CD-R/DVD-ROM DRIVE DISASSEMBLY
CD-R/DVD-ROM
drive
Base cover
Connector M2x3 silver
flat head
Release lever Select bay screws
device M2x8 silver Connector cover
screws
1. Turn the computer upside down. 1. Remove five M2x3 silver flat head screws securing
2. Slide the release lever in the direction of the arrow. the base cover and lift out the cover.
3. Pull out the select bay device in the direction of the 2. Remove two M2x8 silver screws securing the
arrow. connector cover.
3. Remove the connector cover and the connector
from the CD-R/DVD-ROM drive.
TOSHIBA
Tough Enough for Today's World.
Download service manual and resetter printer at http://printer1.blogspot.com
FIELD REPLACEABLE UNIT DOCUMENTATION
TM
Satellite
TE2000
MEMORY MODULE REMOVAL
Memory
slot cover
M2.5x4
black
screws
Memory clips
1. Turn the computer upside down. 4. Spread the memory clips outward and pull the
2. Remove two M2.5x4 black screws securing the memory module out of the connector on a
memory cover. 45 degree angle.
3. Lift out the memory slot cover.
MODEM BOARD REMOVAL
M2x4 silver screws
Modem
harness
Modem slot
cover
M2.5x4 black screw Modem board
1. Remove one M2.5x4 black screw securing the modem 3. Disconnect the modem harness from the modem
slot cover. board.
2. Insert your finger nail or the case separator into the 4. Remove two M2x4 silver screws securing the
notched side of the cover and lift up to release the two modem board.
latches securing the left side of the modem slot cover. 5. Lift up the modem board to disconnect it from the
system board.
TOSHIBA
Tough Enough for Today's World.
Download service manual and resetter printer at http://printer1.blogspot.com
FIELD REPLACEABLE UNIT DOCUMENTATION
TM
Satellite
TE2000
HDD REMOVAL
HDD cover M2.5x6 black screw Plastic Tab HDD pack
1. Turn the computer upside down. 4. Unfold the plastic tab and pull to remove the HDD
2. Remove one M2.5x6 black screw securing from the bay.
HDD cover.
3. Remove the HDD cover.
HDD REMOVAL KEYBOARD REMOVAL
HDD bracket
HDD
M3x4 brass flat head screws
M2.5x12 black screws
5. Remove two M3x4 brass flat head screws securing 1. Turn the computer upside down.
the HDD to the bracket and remove the HDDbracket. 2. Remove two M2.5x12 black screws securing the
keyboard holder.
TOSHIBA
Tough Enough for Today's World.
Download service manual and resetter printer at http://printer1.blogspot.com
FIELD REPLACEABLE UNIT DOCUMENTATION
TM
Satellite
TE2000
KEYBOARD REMOVAL
Latch
Keyboard
Keyboard
lock
Keyboard holder M2.5x2.6 black screws
1. Turn the computer right side up and open the display 3. Remove one M2.5x2.6 black screws securing the
panel. keyboard.
2. Using the case separator, unlatch the keyboard 4. Slide the keyboard lock upward to release the
holder at the top of the keyboard. keyboard.
KEYBOARD REMOVAL WIRELESS LAN CARD REMOVAL
Keyboard
Keyboard
cable
PJ445
Mini PCI cover M2.5x4 security torx screw
5. Lift out the keyboard and set it as shown above. 1. Remove one M2x4 security torx screw securing
6. Disconnect the keyboard cable from PJ445 on the the mini PCI cover and lift out the cover.
system board.
TOSHIBA
Tough Enough for Today's World.
Download service manual and resetter printer at http://printer1.blogspot.com
FIELD REPLACEABLE UNIT DOCUMENTATION
TM
Satellite
TE2000
WIRELESS LAN CARD REMOVAL TOP COVER REMOVAL
M2.5x6 silver screws
M2.5x4
Mini-PCI black flat
connector head
clips screw
Wireless
LAN card
M2.5x12
black
screws
White coax cable Black coax cable
2. Disconnect the black and white coax from the M2.5x20 black screws
wireless LAN card. 1. Turn the computer upside down and remove the
3. Spread the Mini-PCI connector clips and pull the following screws:
Wireless LAN card out of the connector about -9 M2.5x6 black screws
45 degree angle. -1 M2.5x4 black flat head screw
-2 M2.5x20 and 1 M2.5x12 black screws
TOP COVER REMOVAL Rubber seals
M2.5x4 silver screws
Mask seals
2. Turn the computer right side up with the rear facing 5. Remove two mask seals and four rubber seals on
you. the display mask using a pair of fine-tipped tweezers.
3. Remove two M2.5x4 silver screws securing the top 6. Remove two M2.5x6 black screws and four M2x6
cover. silver flat head screws securing the display mask.
4. Open the display panel. 7. There are 23 latches securing the display mask.
Carefully insert your fingers between the mask and the
LCD panel and pry open the latches starting from the
six top latches, to the five latches on each right
and left sides, ending with the bottom seven latches.
TOSHIBA
Tough Enough for Today's World.
Download service manual and resetter printer at http://printer1.blogspot.com
FIELD REPLACEABLE UNIT DOCUMENTATION
TM
Satellite
TE2000
TOP COVER REMOVAL COOLING MODULE REMOVAL
Cooling M2.5x6
M2.5x6 module black
black screw screws
Right
speaker
cable
Left
speaker
cable Fan
cable
PJ311
PJ310
PJ34 LCD/FL harness M2X4 brass screws PJ770
3. Disconnect the left speaker cable from PJ310 and the 1. Disconnect the fan cable from PJ770 on the top
right speaker cable from PJ311 on the top board. board.
4. Disconnect the LCD/FL harness from PJ34 and the IPS 2. Remove four M2x4 brass screws and two M2.5x6
membrane switch fromPJ309 on the system board. black screws securing the cooling module.
5. Remove one M2.5x6 black screw securing the top cover. 3. Lift out the cooling module.
6. Lift out the top cover assembly.
CPU REMOVAL RTC BATTERY REMOVAL
CPU
Close
CPU lock
Open
Silicone grease PJ5 RTC harness RTC Battery
1. Insert a flat head screwdriver in the CPU lock and 1. Disconnect the RTC harness from PJ5 on the
rotate it counter-clockwise to unlock the CPU. Battery/LED board.
2. Lift out the CPU. 2. Lift out the RTC battery.
NOTE: When installing the CPU, make sure that a silicone
grease is applied before attaching the heat sink.
Please refer to FSB-200112 for the complete
procedures on how to apply the silicone grease.
TOSHIBA
Tough Enough for Today's World.
Download service manual and resetter printer at http://printer1.blogspot.com
FIELD REPLACEABLE UNIT DOCUMENTATION
TM
Satellite
TE2000
POWER SUPPLY BOARD REMOVAL SOUND BOARD REMOVAL
System
board
PJ150
Wireless
LAN switch Sound
Power supply button Interface
harness cable
PJ103
Power supply board M2.5x4 black flat head screws SD/Sound board M2.5x4 black flat head screw
1. Disconnect the power supply harness from PJ850 1. Disconnect the sound interface cable from PJ103
and PJ851 on the system board. and the SD interface cable from PJ150 on the
2. Remove one M2.5x4 black flat head screws securing SD/Sound board.
the power supply board. 2. Remove one M2.5x4 black flat head screw
3. Disconnect the power supply board from the system securing the SD/Sound board.
board. 3. Remove the wireless LAN switch button.
4. Lift out the SD/Sound board.
SYSTEM BOARD REMOVAL
PJ803
HDD guide
assy
Select bay
cover SD
interface
cable
Sound
interface
M2.5x6 black flat head screws cable M2.5x4 black flat head screws DC-IN jack harness
1. Remove one M2.5x6 black flat head screw securing 3. Disconnect the following cables from the system board:
the HDD guide assembly and lift out the HDD guide -Sound interface cable from PJ103
assembly. -SD interface cable from PJ150
2. Remove three M2.5x6 black flat head screws securing -DC-IN jack harness from PJ803
the select bay cover and lift out the select bay cover. 4. Remove three M2.5x4 black flat head screws
securing the system board.
5. Lift out the system board.
TOSHIBA
Tough Enough for Today's World.
Download service manual and resetter printer at http://printer1.blogspot.com
FIELD REPLACEABLE UNIT DOCUMENTATION
TM
Satellite
TE2000
MEMBRANE SWITCH REMOVAL SPEAKERS REMOVAL
Membrane
switch assy
Left and right
speakers
M2.5x4 black flat head screws M2.5x4 black flat head screws
1. Remove three M2.5x4 black flat head screws 1. Turn the computer right side up and open the
securing the membrane switch. LCD panel.
2. Lift out the membrane switch assembly. 2. Disconnect the left speaker cable from PJ310 and
right speaker cable from PJ311 on the system board.
3. Remove two M2.5x4 black flat head screws securing
the left and right speakers.
4. Lift out the speakers.
TOSHIBA
Tough Enough for Today's World.
Download service manual and resetter printer at http://printer1.blogspot.com
FIELD REPLACEABLE UNIT DOCUMENTATION
TM
Satellite
TE2000
14.1" DISPLAY MASK REMOVAL FL INVERTER AND 14.1" LCD REMOVAL
Rubber seals M2x5 silver screws LCD module assy
M2x3 M2x3
silver silver
screws screws
LCD/
FL harness
Mask seals FL inverter board M2x4 silver screw FL cable
1. Remove two mask seals and four rubber seals on 1. Remove one M2x5 silver screw securing the
the display mask using a pair of fine-tipped tweezers. FL inverter board.
2. Remove two M2.5x6 black screws and four M2x5 2. Carefully lift up the FL inverter board and
silver flat head screws securing the display mask. disconnect the LCD/FL cable from CN1 and the
3. There are 20 latches securing the display mask. FL cable from CN2.
Carefully insert your fingers between the mask and the 3. Remove two M2x5 silver screws securing the LCD
LCD panel and pry open the latches starting from the bracket.
six top latches, to the five latches on each right 4. Remove four M2X3 silver screws securing the
and left sides, ending with the bottom seven latches. LCD module.
5. Carefully rotate out the top of the LCD module
enough to access the display cable
6. Disconnect the LCD/FL cable from the LCD module.
7. Lift out the LCD module and peel off two
EMI shield/cushion.
TOSHIBA
Tough Enough for Today's World.
Download service manual and resetter printer at http://printer1.blogspot.com