Text preview for : clarion_pn2165mg_mh_mi_mm.pdf part of clarion clarion pn2165mg mh mi mm clarion PN2165MG clarion_pn2165mg_mh_mi_mm.pdf
Back to : clarion_pn2165mg_mh_mi_mm | Home
Clarion Co., Ltd.
Published by Service Dept.
50 Kamitoda, Toda-shi, Saitama 335-8511 Japan
298-6147-00 Feb.2004
Service Dept.: 5-66 Azuma , Kitamoto-shi, Saitama 364-0007 Japan
Tel: +81-48-541-2335 / 2432 FAX: +81-48-541-2703 Printed in Japan
Service Manual
NISSAN Automobile Genuine
AM/FM Radio CD Stereo
Model PN-2165M-G
(Genuine No. 28185 4Z300)
(ID CY338 / Black Escutcheon)
Model PN-2165M-H
(Genuine No. 28185 4Z310)
(ID CY248 / Brown Escutcheon)
Model PN-2165M-I
(Genuine No. 28185 4Z320)
(ID CY358 / Gray Escutcheon)
Model PN-2165M-M
ROCKFORD FOSGAT
(Genuine No. 28185 4Z600)
(ID CY120 / Black Escutcheon)
Quieting sensitivity: AM Less than 32dBu(at 20dB S/N)
ORIGINAL SERVICE MANUAL
FM Less than 10dBu(at 30dB S/N)
This additional service manual is designed to be used to-
Separation: FM More than 20dB(at 1kHz)
gether with original service manual.
Auto tuning stop sensitivity:
Original model Manual No. AM 36 +6/ -6dBu
PN-2165M-A,B,C 298-5779-00 FM 25 +6/ -6dBu
CD section
Disc: 12cm,8cm Disc
DEFFARENCE FROM ORIGINAL
Frequency response: 17Hz to 20kHz(+3/ -3dB)
MODEL Separation: More than 50dB(1kHz,0.5W)
1.Without fix equalizer curcuit of the main PWB section. S/N ratio: More than 74dB(1kHz,5W)
Distortion: Less than 0.4%(1kHz,0.5W)
SPECIFICATIONS General
Radio section Output power: 30W x4
Tuning system: PLL Frequency synthesizer system Power supply voltage: DC14.4V(10.8V to 15.6V)
Receive range: AM 530kHz to 1,710kHz Negative ground
FM 87.9MHz to 107.9MHz Back-up consumption: Less than 3mA
Intermediate frequency: Dimensions(mm): 264.2(W) x63.6(H) x171.9(D)
AM 450 +3/ -3kHz Weight: 1.7kg
FM 10.7 +0.2/ -0.2MHz
PN-2165M-G,H
-1-
PN-2165M-I,M
* Specifications and design are subject to change without 6. Cautions in handling flexible PWB
notice for further improvement. Before working with a soldering iron, make sure that the
COMPONENT iron tip temperature is around 270 . Take care not to apply
the iron tip repeatedly(more than three times)to the same
PN-2165M-G / M-H / M-I / M-M patterns. Also take care not to apply the tip with force.
Main unit ----------- 1 7. Turn the unit OFF during disassembly and parts replace-
NOTE ment. Recheck all work before you apply power to the unit.
8. Cautions in checking that the optical pickup lights up.
We cannot supply PWB with component parts in principle.
The laser is focused on the disc reflection surface through
When a circuit on PWB has failure , please repair it by com-
the lens of the optical pickup. When checking that the la-
ponent parts base. Parts which are not mentioned in ser-
ser optical diode lights up, keep your eyes more than 30cms
vice manual are not supplied.
away from the lens. Prolonged viewing of the laser within
30cms may damage your eyesight.
9. Cautions in handling the optical pickup
To engineers in charge of repair or The laser diode of the optical pickup can be damaged by
electrostatic charge caused by your clothes and body. Make
inspection of our products. sure to avoid electrostatic charges on your clothes or body,
Before repair or inspection, make sure to follow the or discharge static electricity before handling the optical
instructions so that customers and Engineers in pickup.
charge of repair or inspection can avoid suffering 9-1. Laser diode
The laser diode terminals are shorted for transporta-
any risk or injury.
tion in order to prevent electrostatic damage. After
1. Use specified parts.
replacement, open the shorted circuit. When remov-
The system uses parts with special safety features against
ing the pickup from the mechanism, short the termi-
fire and voltage. Use only parts with equivalent character-
nals by soldering them to prevent this damage.
istics when replacing them.
9-2. Actuator
The use of unspecified parts shall be regarded as remod-
The actuator has a powerful magnetic circuit. If a
eling for which we shall not be liable. The onus of product
magnetic material is put close to it. Its characteris-
liability (PL) shall not be our responsibility in cases where
tics will change. Ensure that no foreign substances
an accident or failure is as a result of unspecified parts
enter through the ventilation slots in the cover.
being used.
9-3. Cleaning the lens
2. Place the parts and wiring back in their original positions
Dust on the optical lens affects performance. To
after replacement or re-wiring.
clean the lens, apply a small amount of isopropyl
For proper circuit construction, use of insulation tubes,
alcohol to lens paper and wipe the lens gently.
bonding, gaps to PWB, etc, is involved. The wiring con-
nection and routing to the PWB are specially planned us-
ing clamps to keep away from heated and high voltage
parts. Ensure that they are placed back in their original
positions after repair or inspection.
If extended damage is caused due to negligence during
repair, the legal responsibility shall be with the repairing
company.
3. Check for safety after repair.
Check that the screws, parts and wires are put back se-
curely in their original position after repair. Ensure for safety
reasons there is no possibility of secondary ploblems
around the repaired spots.
If extended damage is caused due to negligence of repair,
the legal responsibility shall be with the repairing company.
4. Caution in removal and making wiring connection to the
parts for the automobile.
Disconnect the battery terminal after turning the ignition
key off. If wrong wiring connections are made with the bat-
tery connected, a short circuit and/or fire may occur. If ex-
tensive damage is caused due to negligence of repair, the
legal responsibility shall be with the repairing company.
5. Cautions regarding chips.
Do not reuse removed chips even when no abnormality is
observed in their appearance. Always replace them with
new ones. (The chip parts include resistors, capacitors,
diodes, transistors, etc). The negative pole of tantalum
capacitors is highly susceptible to heat, so use special care
when replacing them and check the operation afterwards.
PN-2165M-G,H
-2-
PN-2165M-I,M
FEATURES
PN-2165M-G PN-2165M-H PN-2165M-I PN-2165M-M
NISSAN PART NO. 28185 4Z300 28185 4Z310 28185 4Z320 28185 4Z600
ID NO. CY338 CY348 CY358 CY120
RADIO BAND AM/FM AM/FM AM/FM AM/FM
AUTO TUNING SEEK/SCAN SEEK/SCAN SEEK/SCAN SEEK/SCAN
FM DIVERSITY
AM N.C.
GLASS ANT.
INTERFACE AUX CONNECTION
REMOTE CONTROL
PHONE CONNECTION
CD A/C CONNECTION
OTHERS ESCUTCHEON BLACK BROWN GRAY BLACK
ILLUMINATION COLOR WHITE WHITE WHITE WHITE
POWER AMP 30W