Text preview for : 24637B(DASCEInfo).pdf part of Keithley 24637B(DASCEInfo) Keithley DAS 24637B(DASCEInfo).pdf
Back to : 24637B(DASCEInfo).pdf | Home
CE Mark Information for the
DAS-1600/1400/1200 Series
Note: Products that contain the CE Mark are certified to meet European
EMC directive 89/336 EEC. If this directive is not of importance to your
application, please disregard the information in this document.
Keithley MetraByte certifies that this product has been tested and found
to be in compliance with the EMC directive and relevant harmonized
standards.
This document describes the limitation of certification, the declaration of
conformity, and the cabling instructions required for the CE Mark
configuration.
Limitation of Certification
This certification applies only to the operation of the product (with
specified cables and accessories) in the stated configuration and under the
stated operational and environmental specifications. Any modification,
misuse, or improper or inadequate maintenance of the product by the user
voids this certification.
Any deviation from the specific configuration may cause emissions or
susceptibility not within the allowed limits required by the stated
directive. It is the user's responsibility to demonstrate and maintain
compliance with the directive and standards.
Please read the next section, "Declaration of Conformity," for the specific
testing configuration for this product. Consult the Keithley Instruments
GMBH office (European importer) or Technical Support in Taunton, MA,
USA, for further information regarding the exact configuration details and
testing.
Part Number: 24637; Revision B 1
Declaration of Conformity
Application of Council Directive(s) 89/336/EEC
Standard(s) to which Conformity is EN50081-1, EN50082-1
Declared
Manufacturer's Name Keithley MetraByte
Importer's Name Keithley Instruments GMBH
Importer's Address Landsberger Str.65 D-82110 Germering, Munich
Type of Equipment Data Acquisition Plug-in Boards
Model Numbers DAS-1601/CE, DAS-1602/CE, DAS-1201, or DAS-1202
with EXP-1600, an ENCL Series enclosure, FWA-37U,
FWA-EXP, CAB-3740/1/S, STA-U, and S-1800
DAS-1401 or DAS-1402 with EXP-1600, FWA-37U,
FWA-EXP, and CAB-3740/1/S
Year of Manufacture 1995
I, the undersigned, hereby declare that the equipment specified above conforms
to the above Directive(s) and Standard(s).
Place: Taunton, MA USA
___________________________________
(Signature)
Date: 01 January 1996 Mark Urban
(Name)
Quality Assurance Manager
(Position)
2 January 1996
Cabling Instructions for the CE Mark Configuration
When using an EXP-1600 as part of the CE Mark configuration, you must
use an ENCL Series enclosure. The ENCL-1 supports one EXP-1600, the
ENCL-2 supports two EXP-1600s, and the ENCL-4 supports four
EXP-1600s.
Each version of the ENCL Series enclosure contains slotted card guides
and a rear panel that accommodates the rear connectors of each installed
EXP-1600. To install an EXP-1600 in an ENCL Series enclosure,
perform the following steps:
1. Remove the four standoffs from each EXP-1600 to be installed.
2. Insert the EXP-1600 into the slots of a pair of card guides.
3. Gently push the EXP-1600 toward the rear of the desktop enclosure
until the front-panel screws meet the tapped holes on the card guides.
4. Fasten the front-panel screws to the card guides.
An ENCL-4 containing four EXP-1600s is shown in Figure 1.
Figure 1. ENCL-4 Enclosure with Four EXP-1600s Installed
Part Number: 24637; Revision B 3
Once the EXP-1600 is installed in the ENCL Series enclosure, connect
the EXP-1600 directly to the main I/O connector of the
DAS-1600/1400/1200 Series board using the CAB-3740/1/S cable, as
shown in Figure 2. Figure 2 also shows where to attach the FWA-EXP
and FWA-37U. Refer to the DAS board and EXP-1600 user's guides for
more information.
FWA-EXP FWA-37U
J1 P4
DAS-1601/CE, DAS-1602CE,
DAS-1401, DAS-1402,
DAS-1201, or DAS-1202
EXP-1600
P2 P3
Note: When using an EXP-1600, remember to
CAB-3740/1/S configure the channels of the DAS board as
Cable single-ended inputs.
Figure 2. Connecting the DAS Board to an EXP-1600, FWA-EXP, and FWA-37U
The STA-U connects to the DAS-1601/CE, DAS-1602/CE, DAS-1201, or
DAS-1202 board via the S-1800 cable, as shown in Figure 3. One end of
the S-1800 cable attaches to a connector on the STA-U; the other end of
the S-1800 cable attaches to the PIO connector from the DAS board. Note
that the DAS-1401 and DAS-1402 boards do not support the STA-U.
Refer to your DAS board user's guide for more information.
J2 PIO cable S-1800 cable J1 J2 J3
DAS-1601/CE, DAS-1602/CE, STA-U
DAS-1201, or DAS-1202 pin 1 pin 1
Figure 3. Cabling and Connections for Attaching an STA-U
4 January 1996