Text preview for : 05_Alignment & Adjustment.pdf part of Samsung 05 Alignment & Adjustment Samsung LCD TV LW20M21c chassis VE20EO 05_Alignment & Adjustment.pdf
Back to : 05_Alignment & Adjustment | Home
4 Alignments and Adjustments
4 Alignments and Adjustments
4-1 General Alignment Instuction
1. Usually, a color TV-VCR needs only slight touch-up adjustment upon installation.
Check the basic characteristics such as height, horizontal and vertical sync.
2. Use the specified test equipment or its equivalent.
3. Correct impedance matching is essential.
4. Avoid overload. Excessive signal from a sweep generator might overload the front-end of the TV.
When inserting signal markers, do not allow the marker generator to distort test result.
5. Connect the TV only to an DC power source with voltage and frequency as specified on
the backcover nameplate.
6. Do not attempt to connect or disconnect any wire while the TV is turned on.
Make sure that the power cord is disconnected before replacing any parts.
7. To protect aganist shock hazard, use an isolation transform.
LW17M24C/LW20M21C 4-1
4 Alignments and Adjustments
4-2 Factory Mode Adjustments
4-2-1 Entering Factory Mode
1. To enter "Service Mode" Press the remote -control keys in this sequence :
- If you do not have Factory remote - control
INFO Menu
- If you have Factory remote - control
4-2-2 Factory Mode Tree
1. Calibration
2. Option
3. W/B
4. ADC
5 . V C Ti 1 2 7
6. ACC/ACM
7 . Te s t P a t t e r n 0
8. Bus Stop o ff
9. Check Sum 0
10. Reset
T- V N C 1 7 ( 2 0 ) - P E U - 0 0 0 3 2 0 0 4 / 0 4 / 2 0
1. Calibration V C Ti
PC
( 1) RF, VIDE O, S - VIDEO : Factory Mode Calibration V CTi Enter
(2) PC : adjust in VGA MODE.
Based on Master device (VI DEO SIGNAL GENERATOR M SPG-925F)
execute Auto Adjustment in Cross Hatch (also called Combination) (Model : 10, Pattern : 25)
After adjusting 16 Gray Pattern (Model : 10, Pattern : 17)
Factory Mode Calibr ation PC Enter
(3) check 4.ADC of Factory Mode. Adjustment can be done as below.
Value variation can be + 10~20.
_
4-2 LW17M24C/LW20M21C
4 Alignments and Adjustments
2. Option 1 . Vi d e o M u t e O
2. Auto Power On
3. Panel XGA
4. Inch 15
5. Antenna Osd o ff
6. TTXList/Flof Flof
7. Auto FM On
8. Acc/ACM 1
9. Gamma LUT O
10. ESM On
11 . S y s t e m CW
3. W/B(1) R level 128
G level 128
B level 128
R gain 127
G gain 127
B gain 127
g Sub Color 0
g S u b Ti n t 50
Recall
3. W/B(2)
RF RF
Adjustment item [I nitial Data] [Ad just Data] Remark
Red level ADJ[0~255] 128 128 LW17M24C
Green level ADJ[0~255] 128 128 Blue level 118FIX
Red Gain 162FIX
Blue level FIX[0~255] 128 128
Red Gain FIX[0~255] 128 135 LW20M21C
Green Gain ADJ[0~255] 128 135 Blue level 119FIX
Red Gain 136FIX
Blue Gain ADJ[0~255] 128 135
gSUB Color FIX[0~255] 0 0
gSUB T int FIX[0~255] 50 50
Factory Recall * A/S : Micom I nitial Data Write
LW17M24C/LW20M21C 4-3
4 Alignments and Adjustments
4. ADC VCTi PC
Roff set FIX[0~127] 46 Roff set FIX[0~127] 50
Goff set FIX[0~127] 66 Goff set FIX[0~127] 54
Boff set FIX[0~127] 68 Boff set FIX[0~127] 44
Rg ain0 FI X [0~255] 251 Rg ain0 FI X [0~255] 115
Rg ain1 FI X[0 ~ 1] 0 Rg ain1 FI X[0 ~ 1] 1
Gg ain0 FI X[ 0~255] 255 Gg ain0 FI X[ 0~255] 120
Gg ain1 FI X[0 ~ 1] 0 Gg ain1 FI X[0 ~ 1] 1
Bg ain0 FI X[ 0~255] 253 Bg ain0 FI X [0~255] 114
Bg ain1 FI X[0 ~ 1] 0 Bg ain1 FI X[0 ~ 1] 1
5. VCT R Drive 255 RF AGC 0
G Drive 255 Vpeaking 6
B Drive 255 CTI Gain 3
Sub Contrast 44 CTI Coring 5
Sub Bright 0 LMIXOFS 6
Sub Sharp 15 PKCF 3
Sub Color 7 AGCADJ1 32
S u b Ti n t 50 LT I G a i n 15
Sub Coring 5
6. ACC/ ACM Y Max D 7 Up Start 40
Y Scl Thr 64 Low Sn Thr 60
Y Scl A 5 Up Sn Thr 0
Y Scl B 0 Y Min 10
A Ctrl 0 Y Max 255
A Snslp 8 Ym Div Slp 128
T Dixel 12 Fr Age 1
Lower End 80 Fr App 0
Mid Start 30 Esm Ctrl 127
Mid End 100
4-4 LW17M24C/LW20M21C
4 Alignments and Adjustments
7. Test Pattern ( Test Pattern of VCTi)
1) VCTi
2) Toshiba
3) Gray Bar
4) Gray
5) Green
6) Color Bar
7) Cross
8. Bus Stop
- Bus stop is used data communication.
9. Chcek Sum
- Display the current check sum size of the MICOM.
10. Reset
- Initializes the data in the MICOM.
11. T-VNC17(20) PEU-0003 2004/04/20
- Display the MICOM program version.
4-2-3 White Balance
LW17M24C
High Low
285, 295 285, 295
x, y x, y
LW20M21C
High Low
285, 295 280, 295
x, y x, y
LW17M24C/LW20M21C 4-5