Text preview for : SATELLITE 1700 SERIES.pdf part of TOSHIBA SATELLITE 1700 SERIES TOSHIBA Laptop SATELLITE 1700 SERIES.pdf
Back to : SATELLITE 1700 SERIES.pdf | Home
FIELD REPLACEABLE UNIT DOCUMENTATION
TM
Satellite
1700 Series
GENERAL INFORMATION
Tools Required for Proper
Disassembly and Reassembly:
1. Phillips Screwdriver (Size 1)
2. Flat head screwdriver (5mm)
3. Hex driver (5mm)
4. Case Separator
5. ESD Wrist Strap
6. ESD mats
7. Tweezers
Before attempting any of the following procedures,
make sure that the main battery and AC adaptor is
not connected to the unit and the environment in
which you are working on is protected from
Electro-Static Discharge(ESD).
TOSHIBA
Tough Enough for Today's World
FIELD REPLACEABLE UNIT DOCUMENTATION
TM
Satellite
1700Series
TABLE OF CONTENTS:
1. BATTERY PACK REMOVAL
2. OPTIONAL PC CARD REMOVAL
3. MEMORY MODULE REMOVAL
4. KEYBOARD REMOVAL
5. TOP COVER REMOVAL
6. HDD REMOVAL
7. FDD REMOVAL
8. SYSTEM BOARD REMOVAL
9. CD-ROM DRIVE REMOVAL
10. MODEM MODULE REMOVAL
11. COOLING MODULE REMOVAL
12. CPU REMOVAL
13. LED BOARD REMOVAL
14. HINGE BRACKET REMOVAL
15. AUDIO BOARD REMOVAL
16. AUDIO/MEMBRANE SWITCH REMOVAL
17. 12.1'' DISPLAY MASK REMOVAL
18. FL INVERTER AND 12.1'' LCD REMOVAL
19. 13.3'' DISPLAY MASK REMOVAL
20. FL INVERTER AND 13.3'' LCD REMOVAL
TOSHIBA
Tough Enough for Today's World.
FIELD REPLACEABLE UNIT DOCUMENTATION
TM
Satellite
1700Series
BATTERY PACK REMOVAL OPTIONAL PC CARD REMOVAL
Battery lock
Battery pack Battery release lever PC card
Eject button
1. Turn the computer upside down as shown. 1. Pull out the eject button of the PC card to be
2. Press the battery lock and slide the removed.
battery release lever to the right and lift out the battery. 2. Press the eject button and remove the PC card.
NOTE: Before removing any PCMCIA device, make
sure it is "STOPPED" in the PC Card Manager.
MEMORY MODULE REMOVAL KEYBOARD REMOVAL
M2x4 black
screws Latch
Memory
cover
Memory
module
M2.5x3
black screws
Memory clips Keyboard holder
1. Turn the computer upside down. 1. Open the display panel.
2. Remove two M2x4 black screws and remove the 2. Remove two M2.5x3 black screws securing the
memory cover. keyboard holder.
3. Push the memory clips outward and pull the 3. Unlatch the keyboard holder at the top of keyboard
memory module out of the connector on a starting from the left side.
30 degree angle.
TOSHIBA
Tough Enough for Today's World
FIELD REPLACEABLE UNIT DOCUMENTATION
TM
Satellite
1700Series
KEYBOARD REMOVAL
Keyboard
M2.5x3 black screws Keyboard Keyboard cable JP7 JP5 IPS cable
4. Remove four M2x4 black screws securing the 5. Set the keyboard as shown above.
keyboard. 6. Disconnect the keyboard cable from JP7 and
IPS cable from JP5.
7. Lift out the keyboard.
TOP COVER REMOVAL
M2.5x10 black screw
M2.5x8
silver
screws
M2.5x12
black
screws
M2.5x18
black
screws
Lcd harness assy M2.5x3 black screw
1. Remove two M2.5x8 silver screws and M2.5x12 black 4. Remove eight M2.5x18 black screws and one
screws securing the LCD assembly. M2.5x10 black screw securing the bottom cover.
2. Remove one M2.5x3 black screw securing the
LCD harness assembly.
3. Disconnect the LCD harness assembly from the system
board.
TOSHIBA
Tough Enough for Today's World
FIELD REPLACEABLE UNIT DOCUMENTATION
TM
Satellite
1700Series
TOP COVER REMOVAL HDD REMOVAL
M2.5x3
black HDD assy
screws handle
LED cable HDD assy
HDD
M2.5x8
silver
screws
JP4 Sound/IPS switch board Top cover M2.5x8 silver screw
5. Disconnect the sound/IPS switch board from JP4 on the 1. Remove one M2.5x8 silver screw securing the
system board. HDD assembly.
6. Disconnect the LED board cable from the LED board. 2. Grasp the HDD assembly handle and pull it
7. Remove four M2.5x8 silver screws and two M2.5x3 in the direction of the arrow.
black screw securing the top cover assembly. 3. Lift out the HDD assembly.
8 Remove the top cover.
.
HDD REMOVAL FDD REMOVAL
M2.5x4 silver HDD bracket
screws JP6
M2.5x8
FDD silver
cable screw
HDD
FDD assembly
4. Remove four M2.5x3 silver screws securing the HDD 1. Remove one M2.5x8 silver screw securing the FDD
bracket. assembly.
5. Remove the HDD from the HDD bracket. 2. Disconnect the FDD cable from JP6.
3. Lift out the FDD assembly.
TOSHIBA
Tough Enough for Today's World
FIELD REPLACEABLE UNIT DOCUMENTATION
TM
Satellite
1700Series
FDD REMOVAL SYSTEM BOARD REMOVAL
Left bracket
FDD cable
M2.5x8
silver
Right bracket screws
FDD
M2.5x3 black screws
Hex screws
1. Remove three M2.5x3 black screws securing the 1. Remove four hex screws at the rear of the computer.
left and right brackets. 2. Remove two M2.5x8 silver screws near the cooling
2. Lift out the FDD and remove the FDD cable. module.
SYSTEM BOARD REMOVAL CD-ROM DRIVE REMOVAL
PC card CD-ROM
eject button drive assy
M2.5x3 black screws
System board
3. Push the PC Card eject button and lift out the 1. Remove two M2.5x3 black screws securing the
system board as shown above. CD-ROM drive assembly.
2. Slide the CD-ROM drive assembly to the left
to disconnect from system board.
3. Remove all the CD-ROM brackets.
TOSHIBA
Tough Enough for Today's World
FIELD REPLACEABLE UNIT DOCUMENTATION
TM
Satellite
1700Series
MODEM MODULE REMOVAL COOLING MODULE REMOVAL
Cooling
module
Fan cable
Modem JP16
cable
Modem
Mini PCI clips Brass screws
1. Disconnect the modem cable from the modem board. 1. Disconnect the fan cable from JP16 on the system
2. Spread the mini PCI clips securing the modem board board.
and remove the modem board on a 30 degree angle. 2. Remove three brass screws securing the cooling
module.
3. Lift out the cooling module.
CPU REMOVAL LED BOARD REMOVAL
LED
board
Open
CPU lock
slot
Lock
M2.5x3 black screws
1. Using a 5mm flat head screw driver, insert the screwdriver 1. Remove two M2.5x3 black screws securing the
into the CPU lock slot and turn it counterclockwise. LED board.
2. Lift out the LED board.
NOTE: In order to properly lock the CPU, a 5mm flat head
screwdriver must be used.
TOSHIBA
Tough Enough for Today's World
FIELD REPLACEABLE UNIT DOCUMENTATION
TM
Satellite
1700Series
HINGE BRACKET REMOVAL AUDIO BOARD REMOVAL
M2.5x4 Audio
silver board
screws
Audio cable
1. Remove five M2.5x4 silver screws securing 1. Disconnect the audio cable from the audio board.
hinge bracket. 2. Remove two M2.5x4 silver screws securing the
2. Lift out the hinge bracket. audio board.
3. Lift out the Audio board.
AUDIO/MEMBRANE SWITCH REMOVAL
Audio/membrane switch
cable
Audio cable
M2.5x4 M2.5x4
silver silver
screws screws
Left speaker JP3 JP4 Right speaker
1. Remove four M2.5x4 silver screws securing the metal 1. Remove two M2.5x4 silver screws securing
plate. the audio/membrane switch board.
2. Lift out the metal plate 2. Disconnect the left and right speakers from
JP3 and JP4.
3. Disconnect the audio and the audio/membrane switch
cables.
TOSHIBA
Tough Enough for Today's World
FIELD REPLACEABLE UNIT DOCUMENTATION
TM
Satellite
1700Series
12.1" DISPLAY MASK REMOVAL FL INVERTER AND 12.1" LCD REMOVAL
LCD module
Latch
FL cable
Display M2.5x5
mask M2x5 black
brass screws
screws
LCD
LCD/FL inverter cable FL inverter board
Mask seals
1. Remove four mask seals at each corner of the 1. Remove two M2.5x5 black screw securing
display assembly. FL inverter board.
2. Remove four M2.5x5 brass screws securing the 2. Carefully lift up the FL inverter board and
display mask. disconnect the LCD/FL inverter cable from CN1 and
3. There are 22 latches securing the display mask. the FL cable from CN2.
Carefully insert your fingers between the display mask 3. Remove four M3X6 brass screws securing the
and the LCD module and pry open the latches starting LCD module.
from the top six latches, to the five latches on the right 4. Carefully rotate the LCD module from right to left
and left sides, ending with the six bottom latches. of the LCD cover.
5. Disconnect the LCD/FL inverter cable from the LCD
module and remove the LCD from the computer.
TOSHIBA
Tough Enough for Today's World
FIELD REPLACEABLE UNIT DOCUMENTATION
TM
Satellite
1700Series
13.3" DISPLAY MASK REMOVAL FL INVERTER AND 13.3"LCD REMOVAL
LCD module
Latch
FL cable
Display M2.5x5
mask M2x5 black
brass screws
screws
LCD
LCD/FL inverter cable cable FL cable
Mask seals
1. Remove four mask seals at each corner of the 1. Remove one M2.5x5 black screw securing
display assembly. FL inverter board.
2. Remove four M2.5x5 black screws securing the 2. Carefully lift up the FL inverter board and
display mask. disconnect the LCD/FL inverter cable from CN1
3. There are 22 latches securing the display mask. and the FL cable from CN2.
Carefully insert your fingers between the display mask 3. Remove four M2X2 black screws securing the
and the LCD module and pry open the latches starting LCD module.
from the top six latches, to the five latches on the right 4. Carefully rotate the LCD module from right to left
and left sides, ending with the six bottom latches. of the LCD cover.
5. Disconnect the LCD/FL inverter cable from the LCD
module and remove the LCD from the computer.
TOSHIBA
Tough Enough for Today's World