Text preview for : LG_SH4_AFN77441585.pdf part of LG LG SH4 AFN77441585 LG Audio SH4 LG_SH4_AFN77441585.pdf
Back to : LG_SH4_AFN77441585.pdf | Home
Internal Use Only
SERVICE MANUAL
Wireless Sound Bar
SERVICE MANUAL
MODEL: SH4 (SH4, SPH5B-W)
MODEL: SH4
(SH4, SPH5B-W)
CAUTION
BEFORE SERVICING THE UNIT, READ THE "SAFETY PRECAUTIONS"
IN THIS MANUAL.
P/NO : AFN77441585 SEPTEMBER, 2016
CONTENTS
SECTION 1 ........ GENERAL
SECTION 2 ........ CABINET & MAIN CHASSIS
SECTION 3 ........ ELECTRICAL
SECTION 4 ........ WIRELESS SUBWOOFER PART
SECTION 5 ........ REPLACEMENT PARTS LIST
1-1
SECTION 1
GENERAL
CONTENTS
ESD PRECAUTIONS ......................................................................................................................................... 1-3
LOCATION OF CUSTOMER CONTROLS ........................................................................................................ 1-4
ABOUT LED CONDITION ................................................................................................................................. 1-5
WIRELESS SUBWOOFER CONNECTION....................................................................................................... 1-6
HIDDEN KEY MODE ......................................................................................................................................... 1-7
MCS / EQ PROGRAM UPDATE GUIDE ........................................................................................................... 1-8
SPECIFICATIONS ............................................................................................................................................. 1-9
1-2
ESD PRECAUTIONS
Electrostatically Sensitive Devices (ESD)
Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components
commonly are called Electrostatically Sensitive Devices (ESD). Examples of typical ESD devices are integrated
circuits and some field-effect transistors and semiconductor chip components. The following techniques should
be used to help reduce the incidence of component damage caused by static electricity.
1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off
any electrostatic charge on your body by touching a known earth ground. Alternatively, obtain and wear a
commercially available discharging wrist strap device, which should be removed for potential shock reasons
prior to applying power to the unit under test.
2. After removing an electrical assembly equipped with ESD devices, place the assembly on a conductive surface
such as aluminum foil, to prevent electrostatic charge buildup or exposure of the assembly.
3. Use only a grounded-tip soldering iron to solder or unsolder ESD devices.
4. Use only an anti-static solder removal device. Some solder removal devices not classified as "anti-static" can
generate electrical charges sufficient to damage ESD devices.
5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ESD
devices.
6. Do not remove a replacement ESD device from its protective package until immediately before you are
ready to install it. (Most replacement ESD devices are packaged with leads electrically shorted together by
conductive foam, aluminum foil or comparable conductive materials).
7. Immediately before removing the protective material from the leads of a replacement ESD device, touch the
protective material to the chassis or circuit assembly into which the device will by installed.
CAUTION : BE SURE NO POWER IS APPLIED TO THE CHASSIS OR CIRCUIT, AND OBSERVE ALL OTHER
SAFETY PRECAUTIONS.
8. Minimize bodily motions when handing unpackaged replacement ESD devices. (Otherwise harmless motion
such as the brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate
static electricity sufficient to damage an ESD device).
CAUTION. GRAPHIC SYMBOLS
THE LIGHTNING FLASH WITH APROWHEAD SYMBOL. WITHIN AN EQUILATERAL TRIANGLE, IS
INTENDED TO ALERT THE SERVICE PERSONNEL TO THE PRESENCE OF UNINSULATED
"DANGEROUS VOLTAGE" THAT MAY BE OF SUFFICIENT MAGNITUDE TO CONSTITUTE A RISK OF
ELECTRIC SHOCK.
THE EXCLAMATION POINT WITHIN AN EQUILATERAL TRIANGLE IS INTENDED TO ALERT THE
SERVICE PERSONNEL TO THE PRESENCE OF IMPORTANT SAFETY INFORMATION IN SERVICE
LITERATURE.
1-3
LOCATION OF CUSTOMER CONTROLS
FRONT PANEL
Front panel
A D The buttons are located on the rear.
B Standby LED (Red)
C
REAR PANEL
Rear panel
A o/p: : B DC IN :
F : C OPTICAL IN :
D PORTABLE IN :
1/! E USB
F HDMI IN / OUT (TV ARC) :
1-4
ABOUT LED CONDITION
LED Condition Description
USB LED blinks.
BT (Bluetooth Bluetooth
BT (Bluetooth) LED blinks. Bluetooth
HDMI IN .
USB and BT (Bluetooth) LEDs
, Note
LED (Red)
1-5
WIRELESS SUBWOOFER CONNECTION
LED indicator of wireless subwoofer 4. Disconnect and reconnect power cord of the main
unit and the wireless subwoofer.
LED Color Status 5. Turn on the main unit. : The sound bar and wireless
subwoofer will be automatically connected.
Green
Attempting to make connection. - Green LED on the rear of wireless subwoofer
(Blink)
turns on.
Green The connection is completed.
The wireless subwoofer Note:
Red is in standby mode