Text preview for : clarion_dxz938r_155.pdf part of clarion clarion dxz938r 155 clarion DXZ-938 clarion_dxz938r_155.pdf
Back to : clarion_dxz938r_155.pdf | Home
Clarion Co., Ltd. Published by Service Dept.
50 Kamitoda, Toda-shi, Saitama 335-8511 Japan
298-6044-00 JAN. 2003 X
Service Dept.: 5-66 Azuma, Kitamoto-shi, Saitama 364-0007 Japan
Tel: +81-48-541-2335 / 2432 FAX: +81-48-541-2703 Printed in P.R.C.
Service Manual
High End RDS-EON AM/FM Radio
CD Player Combination
Model
(PE-2578E-A )
SPECIFICATIONS NOTE
Radio section * We cannot supply PWB with component parts in principle. When a
Tuning system: PLL synthesizer tuner circuit on PWB has failure, please repair it by component parts
Receiving frequencies: FM 87.5 to 108MHz base. Parts which are not mentioned in service manual are not
(0.05MHz steps) supplied.
MW 531 to 1602kHz * Only CDs and CD-ROMs having the or mark can be
(9kHz steps) used in this unit.
LW 153 to 279kHz Some CDs recorded in CD-R mode may not be usable. Even when
(3kHz steps) recorded in CD-RW mode, some CDs not be usable.
* Specifications and design are subject to change without notice for
CD player section further improvement.
System: Compact disc digital audio * Manufactured under license from Dolby Laboratories.
system "Dolby", "Pro Logic" and the double-D symbol are teademarkes of
Frequency response: 5Hz to 20kHz(+1/-1dB) Dolby Laboratories.
Signal to noise ratio: 100dB(1kHz) IHF-A
Dynamic range: 96dB(1kHz) COMPONENTS
Harmonic distortion: 0.01%
PE-2578E-A
General Source unit 1
Output power: 4x31W(DIN45324, +B=14.4V) Mounting bracket 300-7742-00 1
Power supply voltage: 14.4V DC(10.8 to 15.6V allowable), DCP case 335-6777-00 1
negative ground Escutcheon(OUT-ES) 370-6007-03 1
Power consumption: Less than 15A Extension lead 854-6362-54 1
Speaker impedance: 4ohm(4ohm to 8ohm allowable) Remote control unit RCB-147-700 1
Auto antenna rated current: 500mA or less Parts bag
Weight: Source unit 1.7kg Battery(CR2032) 1
Remote control unit IR plate 291-0088-00 1
30g(including battery) Parts bag
Dimensions(mm): Source unit Removal key 331-2497-00 2
178(W)x50(H)x155(D) Rubber spacer 345-3653-20 1
Remote control unit Screw 716-0726-01 1
32(W)x56(H)x24(D)
DXZ938R
-1-
9-1.Laser diode
To engineers in charge of repair or inspecti-
The laser diode terminals are shorted for transportation in
on of our products. order to prevent electrostatic damage.
After replacement, open the shorted circuit. When removing
Before repair or inspection, make sure to follow the inst-
the pickup from the mechanism, short the terminals by sold-
ructions so that customers and Engineers in charge of ering them to prevent this damage.
repair or inspection can avoid suffering any risk or injury. 9-2.Actuator
1. Use specified parts. The actuator has a powerful magnetic circuit. If a magnetic
The system uses parts with special safety features against fire material is put close to it. Its characteristics will change.
and voltage. Use only parts with equivalent characteristics when Ensure that no foreign substances enter through the ventila-
replacing them. tion slots in the cover.
The use of unspecified parts shall be regarded as remodeling for 9-3.Cleaning the lens
which we shall not be liable. The onus of product liability (PL) shall Dust on the optical lens affects performance. To clean the
not be our responsibility in cases where an accident or failure is as lens, apply a small amount of isopropyl alcohol to lens paper
a result of unspecified parts being used. and wipe the lens gently.
2. Place the parts and wiring back in their original positions after
replacement or re-wiring.
CAUTIONS
For proper circuit construction, use of insulation tubes, bonding,
This appliance contains a laser system and is classified as a
gaps to PWB, etc, is involved. The wiring connection and routing to
"CLASS 1 LASER PRODUCT". To use this model properly, read
the PWB are specially planned using clamps to keep away from
this Owner's Manual carefully and keep this manual for your futu-
heated and high voltage parts. Ensure that they are placed back
re reference. In case of any trouble with this player, please cont-
in their original positions after repair or inspection.
act your nearest "AUTHORIZED service station". To prevent dir-
If extended damage is caused due to negligence during repair, the
ect exposure to the laser beam, do not try to open the enclosure.
legal responsibility shall be with the repairing company.
USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE
3. Check for safety after repair.
OF PROCEDURES OTHER THAN THOSE SPECIFIED IN THE
Check that the screws, parts and wires are put back securely in
OWNER'S MANUAL MAY RESULT IN HAZARDOUS RADIATION
their original position after repair. Ensure for safety reasons there
EXPOSURE.
is no possibility of secondary ploblems around the repaired spots.
If extended damage is caused due to negligence of repair, the
MODEL
legal responsibility shall be with the repairing company.
4. Caution in removal and making wiring connection to the parts for
the automobile.
Disconnect the battery terminal after turning the ignition key off.
If wrong wiring connections are made with the battery connected,
a short circuit and/or fire may occur.
If extensive damage is caused due to negligence of repair, the
legal responsibility shall be with the repairing company.
5. Cautions regarding chips.
Do not reuse removed chips even when no abnormality is obse-
rved in their appearance. Always replace them with new ones.
(The chip parts include resistors, capacitors, diodes, transistors,
etc). The negative pole of tantalum capacitors is highly suscepti-
ble to heat, so use special care when replacing them and check
the operation afterwards.
6. Cautions in handling flexible PWB
Before working with a soldering iron, make sure that the iron tip
temperature is around 270 C. Take care not to apply the iron tip
repeatedly (more than three times) to the same patterns. Also take
care not to apply the tip with force.
7. Turn the unit OFF during disassembly and parts replacement.
Recheck all work before you apply power to the unit.
8. Cautions in checking that the optical pickup lights up.
The laser is focused on the disc reflection surface through the lens
of the optical pickup. When checking that the laser optical diode
lights up, keep your eyes more than 30cms away from the lens.
Prolonged viewing of the laser within 30cms may damage your
eyesight.
9. Cautions in handling the optical pickup
The laser diode of the optical pickup can be damaged by electro-
static charge caused by your clothes and body.
Make sure to avoid electrostatic charges on your clothes or body,
or discharge static electricity before handling the optical pickup.
DXZ938R
-2-
NOTES OF ISO CONNECTOR DUAL ACTION
1. For VW and Audi vehicles, change the position of fuse installation This unit uses Dual Action to make large-screen displays possible.
as shown on the diagram. (Figure 1) When you use the Dual Action, be sure to close it.
EXTENSION CABLE type BE CAREFUL NOT TO GET YOUR FINGERS CAUGHT WHEN
Initial setting of ex-lead OPENING AND CLOSING THE DUAL ACTION.
Fuse
Yellow Yellow 1. For safety's sake, always close the DUAL ACTION before
15A
Fuse Yellow leaving this unit unused for a prolonged period or switching
3A
Red Red
OFF the ignition key.
If you switch OFF the ignition key with the DUAL ACTION tilted,
Blue/White Blue/White
the DUAL ACTION does not close.
2. Before the DUAL ACTION closes, there may be a braking sound
from the safety mechanism. This is normal.
3. If you move the DUAL ACTION by hand, this may create play.
To correct this play, with the power on for the unit, press the
[O] button to close the DUAL ACTION.
4. After a disc is ejected, the DUAL ACTION automatically returns
Green/White Green/White
to the tilted or closed state. If there is any obstruction when the
For models 1992 and later For models up to 1991 DUAL ACTION tries to close, the safety mechanism is triggered
Yellwo Yellwo Yellwo
and the DUAL ACTION returns to the open state. If this happens,
remove the obstruction, then press the [O] button.
Yellwo Yellwo
5. To avoid scratching the compact disc, keep the 12 or 8 cm CD
Red Red Red Red level when inserting or removing them.
Figure 1
2. When the car stereo is installed in 1998 and later Volkswagen
models, make sure to cut the car lead wire connected the A-5
terminal. (A breakdown could occur if the lead wire is not cut.)
After cutting the lead wire, insulate the front end of the lead wire
with insulation tape to prevent the risk of short-circuits.
(Figure 2)
Note: Before cutting the lead wire, disconnect the car battery
- (negative) cable.
Figure 2
3. When the Main unit is also connected to an external amplifier,
connect REMOTE on the external amplifier to the previously
cut lead wire on the side of the connector.
4. When an ex-lead is required in Extension cable type wiring
procedure, remove the auto antenna leads (Blue/White). Be
sure to insulate both the ISO connector side terminal and the
main unit side terminal with insulation tape, respectively.
(Figure 3)
Blue/White Blue/White
Insulation tape
Blue/White Blue/White
Remote turn-on
Insulate the terminal
*Never let the terminals make contact with the metal
plate parts of the car.
Figure 3
DXZ938R
-3-
TROUBLESHOOTING
Problem Cause Measure
Nothing happens when buttons The microprocessor has Turn off the power, then
are pressed. malfunctioned due to noise, etc. press the [RELEASE]
button and remove the
Display is not accurate. DCP.
Press the reset button
with a thin rod.
ERROR DISPLAYS
If an error occurs, one of the following displays is displayed. Take the measures described below to eliminate the problem.
Mode Error Display Cause Measure
ERROR 2 A CD is caught inside the CD deck and is not ejected. This is a failure of CD deck's mechanism.
CD ERROR 3 A CD cannot be played due to scratches, etc. Replace with a non-scratched, non-warped disc.
ERROR 6 A CD is loaded upside-down inside the CD deck and Eject the disc then reload it properly.
does not play.
ERROR 2 A CD inside the CD changer is not loaded. This is a failure of CD changer's mechanism.
CD ERROR 3 A CD inside the CD changer cannot be played due to Replace with a non-scratched, non-warped disc.
changer scratches, etc.
ERROR 6 A CD inside the CD changer cannot be played be- Eject the disc then reload it properly.
cause it is loaded upside-down.
ERROR H Displayed when the temperature in the MD changer is Lower the surrounding temperature and wait for
too high and playback has been stopped automatically. a while to cool off MD changer.
ERROR 2 An MD inside the MD changer is not loaded. This is a failure of MD changer's mechanism.
MD
ERROR 3 An MD inside the MD changer cannot be played due to Replace with a non-scratched, non-warped disc.
changer
scratches, etc.
ERROR 6 An MD inside the MD changer cannot be played be- Eject the disc then reload it properly.
cause it is loaded upside-down.
Displayed when a non-recorded MD is loaded in the Load a pre-recorded MD in the MD changer.
MD changer.
ERROR 2 A DISC inside the DVD changer cannot be played. This is a failure of DVD mechanism.
ERROR 3 A DISC cannot be played due to scratches, etc. Retry or replace with a non-scratched, non-warped
DVD disc.
changer
ERROR 6 A DISC inside the DVD changer cannot be played be- Eject the disc then reload it properly.
cause it is loaded upside-down.
ERROR P Parental level error. Set the correct Parental level.
ERROR R Region code error. Eject the disc and replace correct region code
disc.
If an error display other than the ones described above appears, press the reset button.
ADJUSTMENT
Item Procedure Measuring
instrument
S-meter 1. Turn on the power and press the ENT button & PRESET No.6 button at the same time for about 2 SG
seconds. (TEST MODE)
2. Input the 98.1MHz/30dBu/400Hz or 15KHz (main90%+pilot10%) signal.
3. Adjust the reading of LCD display to [24----00] (2.4V+0.2/-0.2V) by VR101.
4. Push the ENT button & PRESET No.6 button at the same time for 2 seconds once again or do power off
to cancel the TEST MODE.
DXZ938R
-4-
EXPLANATION OF IC:
052-3376-10 M30624MGA-132GP Main System controller
1.Terminal Description
pin 1 : PLL CE : O : The chip enable signal output to the PLL IC. pin 57 : VOL STB : O
: The strobe pulse output to the volume IC.
pin 2 : TIME BASE : IN : Time base pulse input. pin 58 : VOL DT : O
: The serial data output to the volume IC.
pin 3 : CD SBSY : IN : The sub Q data request command input fr- pin 59 : VOL CK : O
: The clock pulse output to the volume IC.
om the CD IC. pin 60 : VCC : -
: Positive supply voltage.
pin 4 : NU : - : Not in use. pin 61 : CATS LED : O
: CATS LED drive output.
pin 5 : SPEED PULSE : IN : The speed pulse input. pin 62 : VSS : -
: Negative supply voltage.
pin 6 : BYTE : IN : Connect to the ground. pin 63 : MOTOR REM : O
: Power supply ON signal output for the slo-
pin 7 : CN VSS : IN : Connect to the ground. pe mechanism motor.
pin 8 : NU : - : Not in use. pin 64 : SLOPE MTR- : O : The slope motor control signal output.
pin 9 : NU : - : Not in use. pin 65 : SLOPE MTR+ : O : The slope motor control signal output.
pin 10 : RESET : IN : Reset signal input. pin 66 : SLOPE V CNT : O : The slope voltage control signal output.
pin 11 : X OUT : O : Crystal connection. pin 67 : OPEN POSI : IN : The open position detect signal input.
pin 12 : VSS : - : Negative supply voltage. pin 68 : NU : - : Not in use.
pin 13 : X IN : IN : Crystal connection. pin 69 : CLOSE POSI : IN : The close position detect signal input.
pin 14 : VCC : - : Positive supply voltage. pin 70 : KEY ILL REM : O : Key illumination ON signal output.
pin 15 : NMI : IN : Connect to the ground. pin 71 : 5V REM : O : 5V power supply ON signal output.
pin 16 : ACC DET : IN : ACC detection signal input. pin 72 : AMP REM DT : IN : Remote controller wire short detection.
pin 17 : BU DET : IN : Backup detection signal input. pin 73 : RDS CLK : IN : RDS clock pulse input.
pin 18 : KEY INT : IN : Key interrupting signal input. pin 74 : SYS MUTE : O : System muting signal output.
pin 19 : 27pinConnect : IN : Connect to pin 27. pin 75 : LINE MUTE : O : The line mute signal output.
pin 20 : SPEED SEL 1 : O : The time constant select signal output for pin 76 : AMP MUTE : O : Muting signal output to the Audio Power A-
the speed pulse counter. mplifier.
pin 21 : SPEED SEL 2 : O : The time constant select signal output for pin 77 : SYS ACC : O : ACC detect signal output.
the speed pulse counter. pin 78 : NU : - : Not in use.
pin 22 : BEEP OUT : O : Beep out. pin 79 : PHONE INT : IN : The telephone interrupt signal input.
pin 23 : RDS CD TST : IN : For the test. pin 80 : NAVI MUTE : O : Muting signal output to suppress the noise
pin 24 : CLK REF : O : Reference clock pulse output. at Navigation sound interrupting.
pin 25 : DCP DET : O : DCP detection signal output. pin 81 : RDS TEST ST : O : Outputting "H" without the test mode.
pin 26 : PULSE DIMM : O : Dimmer pulse output for LCD back light. pin 82 : MUTE SPD UP : O : Station detection speed up command out-
pin 27 : IE BUS RX : IN : IE Bus serial data input. put for RDS.
pin 28 : IE BUS TX : O : IE Bus serial data output. pin 83 : RDS DATA : IN : RDS serial data input.
pin 29 : DSP INIT RST : O : The reset signal output to DSP IC. pin 84 : NOISE DCHG : O : RDS noise discharge signal output.
pin 30 : DSP RST : O : Reset pulse output to the DSP IC. pin 85 : RDS MUTE : O : RDS mute signal output.
pin 31 : AUDIO SEL 1 : O : The select signal output to the audio signal pin 86 : ST SD : IN : At receiving the FM station, this port detec-
input selector. Refer Table 1. ts the stereo signal.
pin 32 : AUDIO SEL 2 : O : The select signal output to the audio signal pin 87 : KEY AD : IN : Input terminal of A/D converter for Key jud-
input selector. Refer Table 1. gment.
pin 33 : DSP SO : O : Serial data output to the DSP IC. pin 88 : S METER : IN : The input terminal of internal A/D converter
pin 34 : DSP SI : IN : Serial data input from the DSP IC. to monitor the radio field strength.
pin 35 : DSP SCK : O : The clock pulse output to DSP IC. pin 89 : NOISE 1 : IN : Input terminal of the internal ADC to sense
pin 36 : DSP RDY : IN : Ready signal input from the DSP IC. the RDS-noise-level.
pin 37 : DSP RQ : O : Request signal output to the DSP IC. pin 90 : W ILL Amber : O : The amber LED control signal output.
pin 38 : CD ZMT CUT : O : Zero cross mute cutting signal output. pin 91 : W ILL Green : O : The green LED control signal output.
pin 39 : DSP S MUTE : O : Soft muting starting signal output to the D- pin 92 : AMP REM OUT : O : Amplifier ON signal output terminal.
SP IC. pin 93 : DIMMER IN : IN : Voltage detector input terminal for Automa-
pin 40 : LD MUTE : O : Muting signal output to the CD mechanism. tic Dimmer.
pin 41 : LD CONT :I/O : Communication line with the CD mechani- pin 94 : A VSS : - : Analog ground.
sm. pin 95 : ILL DET : IN : Illumination ON signal input.
pin 42 : CD TR A : IN : The photo sensor signal input from the CD pin 96 : Vref : - : Reference voltage.
mechanism. pin 97 : A VCC : - : Positive supply voltage for the internal an-
pin 43 : CD TR B : IN : The photo sensor signal input from the CD alog section.
mechanism. pin 98 : PLL SI : IN : Serial data input from the PLL IC.
pin 44 : CD CHK SW : IN : CD disc chucking signal input. pin 99 : PLL SO : O : Serial data output to the PLL IC.
pin 45 : CD SSTOP : IN : At loading, detects the chucking. And next, pin100 : PLL SCK : O : The clock pulse output to the PLL IC.
detects the inside limit of the pick up positi-
on.
pin 46 : CD RESET : O : The reset pulse output to the CD IC.
pin 47 : CD CCE : O : The chip enable signal output to the CD IC. Table 1. The select signal output(audio signal input selector)
pin 48 : CD BU CK : O : CD IC clock pulse output. AUDIO SEL 1 AUDIO SEL 2 AUDIO SEL 3
pin 49 : CD BUS 3 :I/O : The data bus. ( pin 31 ) ( pin 32 ) ( pin 55 )
pin 50 : CD BUS 2 :I/O : The data bus. CD H H L
pin 51 : CD BUS 1 :I/O : The data bus. AUX L H L
pin 52 : CD BUS 0 :I/O : The data bus. TUNER H L L
pin 53 : CD 5V : O : Power supply control signal output for the BUS L L H
CD IC / DAC IC. "H"= ON.
pin 54 : CD 8V : O : Power supply control signal output for the
motor / photo IC. "H"= ON.
pin 55 : AUDIO SEL 3 : O : The select signal output to the audio signal
input selector. Refer Table 1.
pin 56 : BUS I/O : O : The audio signal select command output f-
or Ce-NET.
DXZ938R
-5-
052-7061-01 M30624MGA-E85GP LCD & Ce-NET controller
1.Terminal Description
pin 1 : CONT CONT : O : LCD contrast control voltage output. pin 59 : NU : - : Not in use.
pin 2 : NU : - : Not in use. pin 60 : VCC : - : Positive supply voltage.
pin 3 : NU : - : Not in use. pin 61 : NU : - : Not in use.
pin 4 : NU : - : Not in use. pin 62 : VSS : - : Negative supply voltage.
pin 5 : REMOCON : IN : Remote controller signal input terminal. pin 63 : NU : - : Not in use.
pin 6 : BYTE : IN : Input "L" at single mode operation. pin 64 : NU : - : Not in use.
pin 7 : CN VSS : IN : Input "L" at single mode operation. pin 65 : NU : - : Not in use.
pin 8 : INIT 1 : IN : Destination setting input. Refer Table 1. pin 66 : NU : - : Not in use.
pin 9 : INIT 2 : IN : Destination setting input. Refer Table 1. pin 67 : NU : - : Not in use.
pin 10 : RESET : IN : Reset signal input. pin 68 : NU : - : Not in use.
pin 11 : X OUT : O : Crystal connection. pin 69 : NU : - : Not in use.
pin 12 : VSS : - : Negative supply voltage. pin 70 : NU : - : Not in use.
pin 13 : X IN : IN : Crystal connection. pin 71 : NU : - : Not in use.
pin 14 : VCC : - : Positive supply voltage. pin 72 : NU : - : Not in use.
pin 15 : NMI : IN : Connect to VCC. pin 73 : NU : - : Not in use.
pin 16 : SYS ACC : IN : ACC detect signal input. pin 74 : NU : - : Not in use.
pin 17 : BU DET : IN : Backup detection signal input. pin 75 : NU : - : Not in use.
pin 18 : NU : - : Not in use. pin 76 : NU : - : Not in use.
pin 19 : 27pin connect : IN : Connect to 27pin. pin 77 : JOG CW : IN : Jog key signal input.
pin 20 : NU : - : Not in use. pin 78 : JOG CCW : IN : Jog key signal input.
pin 21 : NU : - : Not in use. pin 79 : NU : - : Not in use.
pin 22 : NU : - : Not in use. pin 80 : NU : - : Not in use.
pin 23 : NU : - : Not in use. pin 81 : NU : - : Not in use.
pin 24 : KEY STANDBY : O : Standby pulse output for the key scan IC. pin 82 : NU : - : Not in use.
pin 25 : ON Board WR : IN : Input "L" at write mode. pin 83 : NU : - : Not in use.
pin 26 : NU : - : Not in use. pin 84 : NU : - : Not in use.
pin 27 : IE BUS RX : IN : IE Bus serial data input. pin 85 : NU : - : Not in use.
pin 28 : IE BUS TX : O : IE Bus serial data output. pin 86 : NU : - : Not in use.
pin 29 : KEY CHIP SEL : O : The chip select signal output to the key pin 87 : NU : - : Not in use.
scan IC. pin 88 : NU : - : Not in use.
pin 30 : KEY CLK : O : The clock pulse output for the key scan pin 89 : NU : - : Not in use.
IC. pin 90 : DCP DET IN : IN : The DCP detection signal input.
pin 31 : KEY DI : IN : Key scan data input. pin 91 : NU : - : Not in use.
pin 32 : KEY DO : O : The serial data output to the Key scan IC pin 92 : NU : - : Not in use.
pin 33 : LCD SO : O : The serial data output to the LCD driver. pin 93 : NU : - : Not in use.
pin 34 : LCD SI : IN : The serial data input from the LCD driver pin 94 : A VSS : - : Analog ground.
pin 35 : LCD CLK : O : The clock pulse output to the LCD driver pin 95 : NU : - : Not in use.
pin 36 : LCD KEY REQ : IN : The key request signal input from the key pin 96 : Vref : - : Reference voltage.
scan IC. pin 97 : A VCC : - : Positive supply voltage for the internal
pin 37 : LCD CS : O : The chip select signal output to the LCD analog section.
driver. pin 98 : NU : - : Not in use.
pin 38 : DISP 5V REM : O : The power supply circuit control signal o- pin 99 : NU : - : Not in use.
utput for DCP. pin100 : NU : - : Not in use.
pin 39 : NU : - : Not in use.
pin 40 : NU : - : Not in use.
pin 41 : NU : - : Not in use.
pin 42 : NU : - : Not in use. Table 1. The destination setting terminal
pin 43 : NU : - : Not in use. North Third
pin 44 : NU : - : Not in use. America area Japan Europa
pin 45 : NU : - : Not in use. INITIAL 1 (pin 8) H L H L
pin 46 : NU : - : Not in use. INITIAL 2 (pin 9) L L H H
pin 47 : NU : - : Not in use.
pin 48 : NU : - : Not in use.
pin 49 : NU : - : Not in use.
pin 50 : NU : - : Not in use.
pin 51 : MUSIC IND : O : ON command output to the indicator for "M-
USIC".
pin 52 : MATRIX IND : O : ON command output to the indicator for "M-
ATRIX".
pin 53 : MOVIE IND : O : ON command output to the indicator for "M-
OVIE".
pin 54 : VIRTUAL IND : O : ON command output to the indicator for "V-
IRTUAL".
pin 55 : DISC IND : O : ON command output to the indicator for "D-
ISC".
pin 56 : SCN IND : O : ON command output to the indicator for "S-
CN".
pin 57 : RPT IND : O : ON command output to the indicator for "R-
PT".
pin 58 : RDM IND : O : ON command output to the indicator for "R-
DM".
DXZ938R
-6-
BLOCK DIAGRAM
DXZ938R
-7-
EXPLODED VIEW PARTS LIST:
DCP section
NO. PART NO. DESCRIPTION Q'TY NO. PART NO. DESCRIPTION Q'TY
1 DCP-427-700 DCP ASSY 1 1-26 347-6710-00 SURGE FILM 1
1-1 371-5708-12 FACE PANEL 1 1-27 347-6759-00 FILM 1
1-2 370-5990-04 ESCUTCHEON 1 1-28 335-6675-02 REAR CVR 1
1-3 382-6388-03 BUTTON(SC/RP/RD) 1 1-29 716-1764-00 SCREW(M1.7x5) 2
1-4 382-6387-04 BUTTON(SAT/OP) 1 1-30 716-0872-11 SCREW(M1.7x6) 10
1-5 382-6385-01 BUTTON(ENT/ISR) 1 1-31 345-8727-00 RUBBER PART 6
1-6 382-6386-00 BUTTON(DISP/AM) 1 1-32 345-8744-00 RUBBER PART 1
1-7 382-6438-00 BUTTON(LEFT) 1 1-33 039-2100-01 SWITCH PWB 1
1-8 382-6437-00 BUTTON(BND) 1 (WITHOUT COMPONENT)
1-9 382-6439-00 BUTTON(RIGHT) 1 1-34 051-6618-18 IC 1
1-10 382-6383-00 BUTTON(BND) 1 1-35 076-0647-00 PLUG 1
1-11 382-6440-00 BUTTON(VSE) 1 1-36 076-0658-08 PLUG 2
1-12 382-6441-00 BUTTON(PL2) 1 1-37 039-2101-00 SWITCH SUB PWB 1
1-13 382-6443-00 BUTTON(ADJ) 1 (WITHOUT COMPONENT)
1-14 382-6442-00 BUTTON(EQ) 1 1-38 331-3322-00 JOG-SW-HOLDER 1
1-15 382-6382-01 BUTTON(4-6) 1 1-39 013-8004-50 ROTARY SW 1
1-16 382-6381-01 BUTTON(1-3) 1 1-40 060-4008-00 IR RECEIVER 1
1-17 382-6389-04 BUTTON(RELEASE) 1 1-41 947-0523-01 KNOB ASSY 1
1-18 335-6676-00 IR FILTER 1 1-42 013-6507-50 LUMI SWITCH 1
1-19 335-6698-00 ILLUMI PLATE 1 1-43 013-6519-50 LUMI SWITCH 18
1-20 335-6697-00 BUTTON HOLDER 1 1-44 001-7043-90 DIODE 10
1-21 335-6696-00 BUTTON HOLDER 1 1-45 001-7040-90 DIODE 1
1-22 750-6722-00 SPRING 1 1-46 001-7064-90 DIODE 8
1-23 347-6707-00 COVER FILM 2 1-47 060-4011-80 PHOTO-TR 1
1-24 347-6708-00 COVER FILM 2 1-48 335-6677-00 LENS 1
1-25 347-6709-00 COVER FILM 1
DXZ938R
-8-
Rear-Escutcheon section
NO. PART NO. DESCRIPTION Q'TY NO. PART NO. DESCRIPTION Q'TY
1 371-5709-04 FACE PANEL 1 15 001-7055-90 DIODE 6
2 347-6666-00 IND-FILM(L) 1 16 001-7062-90 DIODE 10
3 335-6772-00 ILLUMI PARTS 1 17 345-8726-00 RUBBER PART 1
4 347-5161-00 DOUBLE FACE 2 18 716-0872-02 PAD SCREW(M1.7x5) 4
5 370-5991-04 ESCUTCHEON 1 19 013-7411-60 DETECTOR SWITCH 1
6 331-3336-01 LCD-CVR 1 20 051-6057-00 IC 1
7 347-6813-00 DOUBLE FACE 2 21 052-7061-01 MICON 1
8 347-6683-01 FILM 1 22 074-1195-78 OUTLET SOCKET 1
9 379-1227-51 INDICATOR 1 23 013-6507-50 LUMI SWITCH 1
10 345-8715-01 RUBBER CONNECT 2 24 347-6665-00 IND-FILM(R) 1
11 347-6682-00 FILM 1 25 347-6501-00 DOUBLE FACE 1
12 335-6682-01 LCD HOLDER 1 26 347-6522-00 DOUBLE FACE 1
13 347-6606-00 REFLECTOR 1
14 039-2272-00 LCD PWB 1
(WITHOUT COMPONENT)
DXZ938R
-9-
Inner-Escutcheon section
Grease application
Note)Grease uses FLOIL G-31SB.
NO. PART NO. DESCRIPTION Q'TY NO. PART NO. DESCRIPTION Q'TY
1 716-1715-02 SCREW(M2) 9 10 750-6714-00 SPRING(HOOK) 1
2 074-1278-01 OUTLET SOCKET 1 11 341-1770-00 SHAFT(HOOK) 1
3 347-6760-00 INSULATOR 1 12 335-6680-02 SIDE-CVR(F-LEFT) 1
4 039-1862-00 FPC 1 13 335-6679-02 SIDE-CVR(F-RIGHT) 1
(WITHOUT COMPONENT) 14 341-1769-00 ROLLER(ARM) 2
5 947-0525-01 DCP-HOLD-ASSY 1 15 331-3329-00 LEVER-MID(R) 1
6 347-6761-00 INSULATOR 1 16 331-3327-00 LEVER-UP(R) 1
7 345-8728-00 SPACER(CUSHION) 2 17 331-3330-01 LEVER-MID(L) 1
8 335-6678-00 CN-CVR 1 18 331-3328-00 LEVER-UP(L) 1
9 335-6683-00 HOOK 1 19 947-0524-01 DISP-HOLDE-ASSY 1
DXZ938R
-10-
NO. PART NO. DESCRIPTION Q'TY NO. PART NO. DESCRIPTION Q'TY
20 370-6005-04 ESCUTCHEON 1 46 946-0079-01 GEAR-BOX ASSY 1
21 341-1767-00 SPACER(GEAR) 3 47 347-6832-00 SPACER(MOTOR) 1
22 309-0782-01 FRONT PLATE 1 48 947-0513-02 T-LIM-GEAR ASSY 1
23 613-0725-01 IDLLER-GEAR 2 49 341-1788-00 ROLLER(SIDE) 2
24 335-6505-00 ILLUMI PLATE 1 50 335-6766-02 SIDE-CVR(L) 1
25 613-0726-01 SW-GEAR 1 51 335-6765-02 SIDE-CVR(R) 1
26 750-6740-00 SPRING(ARM-UP) 2 52 346-0150-02 LEATHER SHEET 1
27 716-0872-02 PAD SCREW(M1.7x5) 15 53 750-6726-00 SPRING(INNER)R 1
28 780-2005-00 SCREW(M2x5) 4 54 335-6807-01 FRONT COVER(L) 1
29 854-4380-01 EX-LEAD 1 55 335-6806-01 FRONT COVER(R) 1
30 341-1783-00 SPACER(SCREW) 2 56 331-3480-00 SUPPORT PLATE(L-R) 2
31 341-1784-00 SPACER(UP-ARM-P) 2 57 347-6767-00 FILM 2
32 750-3432-00 SPRING(MOTOR) 1 58 716-1872-01 SCREW(M2x4x1.5) 2
33 613-0733-00 HUS-GEAR 1 59 750-6727-00 SPRING(INNER)L 1
34 746-0768-20 WASHER( 4.3-1.6/t0.5) 6 60 382-6506-02 BUTTON(EJECT) 1
35 613-0717-00 INPUT-GEAR 1 61 347-6536-00 PROTECT SHEET 1
36 634-0024-00 MOTOR ASSY 1 62 716-3475-00 SCREW(M2x6) 2
37 291-0098-00 STICKER 1 63 347-6768-00 SHADE 2
38 341-1791-00 SPACER(GEAR) 1 64 750-6732-01 SPRING 1
39 345-8729-00 CUSHION(IN-ES) 1 65 347-6215-00 SPACER FILM 1
40 331-3401-01 LINK-HOLDER(L) 1 66 347-6951-00 PROTECTOR SHEET 1
41 331-3400-01 LINK-HOLDER(R) 1 67 347-6835-00 SPACER 1
42 716-1468-20 SCREW(M2x2.5) 9 68 347-6878-00 PROTECT SHEET 2
43 947-0528-01 INNER-BRKT ASSY 1 69 746-0917-00 WASHER 1
44 947-0519-01 LOWER-LEVER ASSY 1
45 716-1758-00 PAD SCREW(M2x5) 3
Main section
Exploded view on next page
NO. PART NO. DESCRIPTION Q'TY NO. PART NO. DESCRIPTION Q'TY
1 DCP-427-700 DCP ASSY 1 23 331-2946-01 SHIELD CVR(R) 1
2 880-2089C TUNER 1 24 331-2869-00 SHIELD CASE 1
3 013-7106-00 DETECTOR SWITCH 1 25 331-3378-00 SW HOLDER 1
4 042-0576-00 DOUBLE-LAYER-C 1 26 335-0833-01 LEAD HOLDER 1
5 060-0100-01 BUZZER 1 27 714-3006-81 MACHINE SCREW(M1.7x5) 4
6 074-1106-12 OUTLET SOCKET 2 28 731-3006-80 TAPTIGHT(M3x6) 8
7 074-1194-00 OUTLET SOCKET 1 29 731-3008-87 TAPTIGHT(M3x8) 2
8 074-1214-00 OUTLET SOCKET 1 30 855-5454-50 RCA PIN CORD 1
9 076-0312-02 PLUG 1 31 855-5458-50 RCA PIN CORD 1
10 092-4000-51 ANT-RECEPT 1 32 051-2038-10 IC HOLDER 1
11 101-0941-00 TRANSISTOR 1 33 039-2271-01 MAIN PWB 1
12 103-2012-00 TRANSISTOR 2 (WITHOUT COMPONENT)
13 103-2353-00 TRANSISTOR 1 34 013-7206-50 DETECTOR SWITCH 1
14 305-0274-31 SIDE CVR(L) 1 35 074-1198-68 OUTLET SOCKET 1
15 305-0275-30 SIDE CVR(R) 1 36 074-1138-76 OUTLET SOCKET 1
16 307-0616-03 REAR CVR 1 37 074-1199-80 OUTLET SOCKET 1
17 313-1844-00 HEAT SINK 1 38 001-7011-96 DIODE 1
18 313-1845-00 HEAT SINK 1 39 076-0659-12 PLUG 2
19 313-1651-21 HEAT SINK 1 40 039-2102-00 SUB PWB 1
20 313-1853-00 HEAT SINK 1 (WITHOUT COMPONENT)
21 331-2255-20 IC HOLDER 1 41 039-1164-00 FPC 1
22 331-2945-00 SHIELD CVR(F) 1 (WITHOUT COMPONENT)
DXZ938R
-11-
NO. PART NO. DESCRIPTION Q'TY NO. PART NO. DESCRIPTION Q'TY
42 331-1709-00 EARTH PLATE 1 56 714-2603-81 MACHINE SCREW 8
43 331-2744-00 STOPPER 1 57 731-3006-40 TAPTIGHT(M3x6) 1
44 331-2929-00 SHIELD CVR(V) 1 58 816-2569-50 FLAT WIRE 1
45 331-2930-00 SHIELD CVR(L) 1 59 929-0220-83 CD-MECHANISM 1
46 331-3324-00 CD-SUB BRKT(R) 1 60 303-0472-00 UPPER CVR 1
47 331-3417-00 CD-SUB BRKT(F) 1 61 304-0460-01 LOWER CVR 1
48 345-3799-20 RUBBER PART 8 62 286-6132-01 SETPLATE 1
49 345-8513-00 SPACE 1 63 347-6821-00 SPACE FILM 2
50 347-6215-00 SPACE-FILM 1 64 345-5192-00 CUSHION 1
51 347-6245-00 FILM 1 65 716-0872-02 PAD SCREW(M1.7x5) 2
52 347-6285-00 INSULATOR 1 66 ----------------- REAR-ES ASSY 1
53 347-6681-00 INSULATOR 1 67 347-6536-00 PROTECT SHEET 1
54 347-6705-00 INSULATOR 1 68 ----------------- INNER-ES ASSY 1
55 347-6729-00 INSULATOR 1
DXZ938R
-12-
ELECTRICAL PARTS LIST: Note) Several different parts of the same reference number are altemative parts.
Main PWB (B1) section One of those parts is used in the set.
REF No. PART No. DESCRIPTION REF No. PART No. DESCRIPTION REF No. PART No. DESCRIPTION
BL 1 880-2089C TUNER C 223 168-2232-55 25V 0.022uF C 417 042-0416-52 10V 10uF TAN
C1 168-2232-55 25V 0.022uF C 224 172-4731-15 50V 0.047uF C 418 168-1042-78 50V 0.1uF
C2 163-4753-55 35V 4.7uF C 230 042-0631-50 10V 100uF C 419 168-1042-78 50V 0.1uF
C4 163-1053-65 50V 1uF C 241 163-1063-35 16V 10uF C 420 042-0416-52 10V 10uF TAN
C5 168-2232-55 25V 0.022uF C 242 168-1032-55 50V 0.01uF C 423 168-1042-78 50V 0.1uF
C6 168-2232-55 25V 0.022uF C 243 183-1073-27 10V 100uF C 424 168-1042-78 50V 0.1uF
C7 183-4763-37 16V 47uF C 244 183-1073-17 6.3V 100uF C 427 168-1042-78 50V 0.1uF
C8 168-2232-55 25V 0.022uF C 245 168-1042-78 50V 0.1uF C 428 168-1042-78 50V 0.1uF
C9 168-2232-55 25V 0.022uF C 246 166-1011-50 50V 100pF C 429 042-0416-52 10V 10uF TAN
C 10 168-6822-55 50V 6800pF C 250 042-0505-81 10V 22uF C 431 042-0416-52 10V 10uF TAN
C 11 042-0631-50 10V 100uF C 251 168-1042-78 50V 0.1uF C 433 168-1042-78 50V 0.1uF
C 12 042-0631-50 10V 100uF C 252 042-0452-81 10V 220uF C 434 168-1042-78 50V 0.1uF
C 14 166-1011-50 50V 100pF C 253 166-2211-50 50V 220pF C 435 168-1042-78 50V 0.1uF
C 16 168-1042-78 50V 0.1uF C 254 168-1042-78 50V 0.1uF C 436 042-0416-52 10V 10uF TAN
C 17 168-1222-55 50V 1200pF C 256 042-0505-81 10V 22uF C 437 166-1011-50 50V 100pF
C 18 163-1053-65 50V 1uF C 257 168-2232-55 25V 0.022uF C 438 168-1032-55 50V 0.01uF
C 19 168-8222-55 50V 8200pF C 258 042-0416-52 10V 10uF TAN C 439 178-4742-78 25V 0.47uF
C 20 163-4763-15 6.3V 47uF C 259 042-0505-80 25V 1uF C 440 168-1022-55 50V 1000pF
C 21 168-2232-55 25V 0.022uF C 301 163-1053-65 50V 1uF C 441 168-1042-78 50V 0.1uF
C 22 166-1011-50 50V 100pF C 302 163-1053-65 50V 1uF C 442 042-0416-52 10V 10uF TAN
C 23 166-1011-50 50V 100pF C 303 166-1201-50 50V 12pF C 450 163-1063-35 16V 10uF
C 24 166-3311-50 50V 330pF C 304 166-1201-50 50V 12pF C 451 163-1063-35 16V 10uF
C 25 166-1501-50 50V 15pF CH C 305 166-1201-50 50V 12pF C 452 163-1063-35 16V 10uF
C 26 166-1801-50 50V 18pF CH C 306 166-1201-50 50V 12pF C 453 163-1063-35 16V 10uF
C 28 168-2232-55 25V 0.022uF C 307 163-1063-35 16V 10uF C 454 163-1063-35 16V 10uF
C 29 168-2232-55 25V 0.022uF C 308 163-2263-35 6.3V 22uF C 455 163-1063-35 16V 10uF
C 30 166-1011-50 50V 100pF C 309 163-1063-35 16V 10uF C 456 163-2263-15 6.3V 22uF
C 55 166-2201-50 50V 22pF CH C 311 043-0264-63 0.01uF C 457 163-2263-15 6.3V 22uF
C 66 166-2201-50 50V 22pF CH C 312 043-0264-63 0.01uF C 458 163-2263-15 6.3V 22uF
C 67 168-1032-55 50V 0.01uF C 313 166-1201-50 50V 12pF C 459 163-2263-15 6.3V 22uF
C 68 168-1022-55 50V 1000pF C 314 166-1201-50 50V 12pF C 460 163-2263-15 6.3V 22uF
C 102 178-1052-78 25V 1uF C 315 163-1063-35 16V 10uF C 461 163-2263-15 6.3V 22uF
C 103 178-1052-78 25V 1uF C 316 163-1063-35 16V 10uF C 462 166-2201-50 50V 22pF
C 104 178-1052-78 25V 1uF C 317 163-1063-35 16V 10uF C 463 166-2201-50 50V 22pF
C 105 178-1052-78 25V 1uF C 318 163-1063-35 16V 10uF C 464 166-2201-50 50V 22pF
C 106 042-0560-84 16V 47uF C 319 163-1063-35 16V 10uF C 465 166-2201-50 50V 22pF
C 107 042-0560-63 16V 22uF C 320 163-1063-35 16V 10uF C 466 166-2201-50 50V 22pF
C 108 172-2231-15 50V 0.022uF C 321 168-4732-78 25V 0.047uF C 467 166-2201-50 50V 22pF
C 109 042-0560-56 50V 3.3uF C 326 163-1063-35 16V 10uF C 526 163-1063-35 16V 10uF
C 110 043-0296-50 0.1uF C 327 163-1063-35 16V 10uF C 527 163-1063-35 16V 10uF
C 111 043-0296-50 0.1uF C 328 163-1063-35 16V 10uF C 528 163-1063-35 16V 10uF
C 112 043-0296-50 0.1uF C 329 163-1063-35 16V 10uF C 529 163-1063-35 16V 10uF
C 113 043-0296-50 0.1uF C 330 163-1063-35 16V 10uF C 545 163-1063-35 16V 10uF
C 114 043-0505-50 2.2uF C 331 163-1063-35 16V 10uF C 546 163-1063-35 16V 10uF
C 115 043-0505-50 2.2uF C 332 163-1063-35 16V 10uF C 547 163-4763-15 6.3V 47uF
C 116 168-4722-55 50V 4700pF C 333 163-1063-35 16V 10uF C 606 168-4732-78 25V 0.047uF
C 118 043-0505-50 2.2uF C 334 163-1063-35 16V 10uF C 612 168-1032-55 50V 0.01uF
C 119 043-0505-50 2.2uF C 335 163-1063-35 16V 10uF C 613 042-0576-00 5.5V 0.1F
C 126 178-1052-78 25V 1uF C 401 166-1021-50 50V 1000pF C 614 168-1032-55 50V 0.01uF
C 127 178-1052-78 25V 1uF C 402 166-1021-50 50V 1000pF C 615 042-0577-00 6.3V 100uF
C 128 178-1052-78 25V 1uF C 403 042-0416-52 10V 10uF TAN C 616 163-1063-35 16V 10uF
C 129 178-1052-78 25V 1uF C 404 168-1042-78 50V 0.1uF C 617 168-1022-55 50V 1000pF
C 210 042-0423-92 6.3V 4.7uF TAN C 405 042-0416-52 10V 10uF TAN C 618 168-1032-55 50V 0.01uF
C 211 163-2263-35 16V 22uF C 406 042-0416-52 10V 10uF TAN C 619 168-4732-78 25V 0.047uF
C 212 168-4732-78 25V 0.047uF C 407 042-0416-52 10V 10uF TAN C 620 178-2242-78 25V 0.22uF
C 213 163-2263-35 16V 22uF C 408 168-1042-78 50V 0.1uF C 622 166-1011-50 50V 100pF
C 214 042-0545-00 16V 2200uF C 409 168-1042-78 50V 0.1uF C 623 166-1011-50 50V 100pF
C 216 042-0563-71 16V 100uF C 410 042-0416-52 10V 10uF TAN C 624 168-2232-55 25V 0.022uF
C 217 182-1073-35 16V 100uF C 411 168-1042-78 50V 0.1uF C 627 168-1042-78 50V 0.1uF
C 220 042-0631-50 10V 100uF C 412 042-0416-52 10V 10uF TAN C 628 166-1011-50 50V 100pF
C 221 163-1063-35 16V 10uF C 413 042-0416-52 10V 10uF TAN C 629 042-0397-55 6.3V 3.3uF TAN
C 222 184-4763-41 25V 47uF C 416 168-1042-78 50V 0.1uF C 801 168-2232-55 25V 0.022uF
DXZ938R
-13-
REF No. PART No. DESCRIPTION REF No. PART No. DESCRIPTION REF No. PART No. DESCRIPTION
C 802 168-8212-55 50V 820pF D 902 001-0517-90 SS355 L 421 010-2285-58 BLM21A102FPB
C 803 168-6812-55 50V 680pF D 903 001-0516-90 MA111 L 422 010-2285-58 BLM21A102FPB
C 804 168-1032-55 50V 0.01uF D 903 001-0517-90 SS355 L 423 010-2285-58 BLM21A102FPB
C 805 168-2232-55 25V 0.022uF F 200 060-8023-52 CHIP FUSE L 424 010-2285-58 BLM21A102FPB
C 807 163-2253-65 50V 2.2uF FIL 401 060-3110-90 NFM4516P13C204 L 425 010-2285-58 BLM21A102FPB
C 808 166-3311-50 50V 330pF FIL 404 060-3110-90 NFM4516P13C204 L 426 010-2285-58 BLM21A102FPB
C 809 166-5611-50 50V 560pF IC 1 051-6201-90 LC72146M L 427 010-2285-58 BLM21A102FPB
C 810 166-4701-50 50V 47pF IC 101 051-2038-10 LA47501 L 428 010-2285-56 BLM21B222S
C 811 166-5601-50 50V 56pF IC 201 051-3605-90 NJM2360A L 429 010-2285-56 BLM21B222S
C 812 163-4763-15 6.3V 47uF IC 220 051-3201-90 AN77L06 L 430 010-2285-56 BLM21B222S
C 813 168-1042-78 50V 0.1uF IC 230 051-1014-08 TA7291F L 431 010-2285-56 BLM21B222S
C 902 168-4722-55 50V 4700pF IC 301 051-0410-38 MC14052BF2A L 432 010-2285-56 BLM21B222S
C 905 168-1042-78 50V 0.1uF IC 302 051-1811-90 BA3129F L 433 010-2285-56 BLM21B222S
CCT401 010-3042-54 BLA3216A601SG4 IC 303 051-3034-90 NJM4558V L 434 010-2285-56 BLM21B222S
CCT402 010-3042-54 BLA3216A601SG4 IC 304 051-0556-93 NJM2058M L 435 010-2285-56 BLM21B222S
CCT403 010-3042-54 BLA3216A601SG4 IC 305 051-7232-08 74VHC4066 L 436 010-2285-56 BLM21B222S
CCT404 010-3042-54 BLA3216A601SG4 IC 401 051-6350-00 AK7716 L 437 010-2285-56 BLM21B222S
CCT405 010-3042-54 BLA3216A601SG4 IC 402 051-9109-50 T15M256A L 441 010-2285-56 BLM21B222S
CCT406 010-3042-54 BLA3216A601SG4 IC 405 051-6379-08 AK4351 L 442 010-2285-56 BLM21B222S
D 102 001-2403-90 MIF60 IC 406 051-6620-08 TC9246F L 450 010-2285-56 BLM21B222S
D 103 001-2403-90 MIF60 IC 450 051-3026-90 NJM4580V L 451 010-2285-56 BLM21B222S
D 104 001-2403-90 MIF60 IC 451 051-3026-90 NJM4580V L 452 010-2285-56 BLM21B222S
D 105 001-2403-90 MIF60 IC 452 051-3026-90 NJM4580V L 453 010-2285-56 BLM21B222S
D 106 001-2403-90 MIF60 IC 502 051-6600-38 CA0008AM L 602 010-2323-53 2.2uH
D 107 001-2403-90 MIF60 IC 503 051-0350-93 NJM4558M L 605 010-2198-56 2.2uH
D 108 001-2403-90 MIF60 IC 504 052-3376-10 M30624MGA-132GP L 606 010-2198-56 2.2uH
D 109 001-2403-90 MIF60 IC 505 051-5437-08 S-80821ANMP L 607 010-2198-56 2.2uH
D 110 001-0529-44 MA8082M IC 506 051-0869-58 NJM2103M L 801 010-2275-53 220uH
D 200 001-2606-90 MIFS4 IC 509 051-5017-00 TC9482F L 901 010-2285-51 BLM21A05PT
D 202 001-0504-46 HZS9B2L IC 801 051-3034-90 NJM4558M L 902 010-2285-51 BLM21A05PT
D 203 001-0592-00 RM4Z IC 802 051-4607-90 SAA6581T P 450 855-5424-50 RCA PIN CORD
D 210 001-0516-90 MA111 IC 901 051-1215-08 74HC132AF P 451 855-5458-50 RCA PIN CORD
D 210 001-0517-90 SS355 J 501 074-1106-12 12P Q3 193-1306-00 2SD1306
D 211 001-0516-90 MA111 J 502 074-1106-12 12P Q4 125-0002-93 RN2403
D 211 001-0517-90 SS355 J 601 074-1194-00 13P CE-NET Q6 190-1162-00 2SA1162
D 219 001-0347-11 MA4030M J 602 074-1138-76 26P Q7 190-1162-00 2SA1162
D 220 001-0504-33 HZS6B2L J 603 074-1198-68 18P Q8 125-2004-93 RN1403
D 221 001-0466-90 S5688B J 604 074-1199-80 30P Q9 198-0669-00 2SK669
D 222 001-0466-90 S5688B J 605 076-0312-02 2P Q 201 198-0241-50 2SK241YGR
D 223 001-0516-90 MA111 J 903 074-1214-00 16P Q 202 103-2353-00 2SD2353
D 223 001-0517-90 SS355 L1 010-2275-53 220uH Q 210 190-1298-00 2SA1298
D 225 001-0466-91 S5688G L2 010-3407-59 5.6uH Q 211 125-2004-96 RN1406
D 226 001-0529-35 MA8062M L3 010-2285-58 BLM21A102FPB Q 212 190-1162-00 2SA1162
D 228 001-0347-11 MA4030M L4 010-2285-58 BLM21A102FPB Q 213 192-2712-00 2SC2712
D 230 001-0504-42 HZS7B3L L 52 010-4046-00 30uH Q 220 103-2012-00 2SD2012
D 241 001-0504-45 HZS9B1L L 101 010-8024-00 CHOKE Q 221 198-0241-50 2SK241YGR
D 501 001-0516-90 MA111 L 210 010-6003-03 270uH