Text preview for : 32FS2ANB Service Manual.pdf part of LG 32FS2ANB Service Manual LG TV 32FS2AMB chassis MC-05HA 32FS2ANB Service Manual.pdf
Back to : 32FS2ANB Service Manual.p | Home
website:http://biz.LGservice.com
e-mail:http://www.LGEservice.com/techsup.html
COLOR TV
SERVICE MANUAL
CHASSIS : MC-05HA
MODEL : 32FS2AMB/ANB
MODEL : 29FS2AMB/ANB-TE
CAUTION
BEFORE SERVICING THE CHASSIS,
READ THE SAFETY PRECAUTIONS IN THIS MANUAL.
CONTENTS
CONTENTS .............................................................................................. 2
SAFETY PRECAUTIONS ..........................................................................3
CONTROL DESCRIPTIONS .................................................................... 4
SPECIFICATIONS .................................................................................... 7
ADJUSTMENT INSTRUCTIONS ............................................................. 8
TROUBLE SHOOTING .......................................................................... 17
PRINTED CIRCUIT BOARD ....................................................................20
BLOCK DIAGRAM ................................................................................. 24
EXPLODED VIEW .................................................................................. 28
EXPLODED VIEW PARTS LIST ..............................................................29
REPLACEMENT PARTS LIST ............................................................... 30
SVC. Sheet ..................................................................................................
SAFETY PRECAUTIONS
IMPORTANT SAFETY NOTICE
Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in
the Schematic Diagram and Replacement Parts List.
It is essential that these special safety parts should be replaced with the same components as recommended in this manual to
prevent X-RADIATION, Shock, Fire, or other Hazards.
Do not modify the original design without permission of manufacturer.
General Guidance Before returning the receiver to the customer,
An Isolation Transformer should always be used during always perform an AC leakage current check on the
the servicing of a receiver whose chassis is not isolated from exposed metallic parts of the cabinet, such as antennas,
the AC power line. Use a transformer of adequate power rating terminals, etc., to be sure the set is safe to operate without
as this protects the technician from accidents resulting in damage of electrical shock.
personal injury from electrical shocks.
Leakage Current Cold Check(Antenna Cold Check)
It will also protect the receiver and it's components from being With the instrument AC plug removed from AC source,
damaged by accidental shorts of the circuitry that may be connect an electrical jumper across the two AC plug prongs.
inadvertently introduced during the service operation. Place the AC switch in the on position, connect one lead of
ohm-meter to the AC plug prongs tied together and touch other
If any fuse (or Fusible Resistor) in this TV receiver is blown, ohm-meter lead in turn to each exposed metallic parts such as
replace it with the specified. antenna terminals, phone jacks, etc.
If the exposed metallic part has a return path to the chassis, the
When replacing a high wattage resistor (Oxide Metal Film measured resistance should be between 1M and 5.2M.
Resistor, over 1W), keep the resistor 10mm away from PCB. When the exposed metal has no return path to the chassis the
reading must be infinite.
Keep wires away from high voltage or high temperature parts. An other abnormality exists that must be corrected before the
receiver is returned to the customer.
Due to high vacuum and large surface area of picture tube,
extreme care should be used in handling the Picture Tube. Leakage Current Hot Check (See below Figure)
Do not lift the Picture tube by it's Neck. Plug the AC cord directly into the AC outlet.
Do not use a line Isolation Transformer during this check.
X-RAY Radiation Connect 1.5K/10watt resistor in parallel with a 0.15uF capacitor
between a known good earth ground (Water Pipe, Conduit, etc.)
Warning: and the exposed metallic parts.
Measure the AC voltage across the resistor using AC
The source of X-RAY RADIATION in this TV receiver is the voltmeter with 1000 ohms/volt or more sensitivity.
High Voltage Section and the Picture Tube. Reverse plug the AC cord into the AC outlet and repeat AC
For continued X-RAY RADIATION protection, the voltage measurements for each exposed metallic part. Any
replacement tube must be the same type tube as specified in voltage measured must not exceed 0.75 volt RMS which is
the Replacement Parts List. corresponds to 0.5mA.
In case any measurement is out of the limits specified, there is
possibility of shock hazard and the set must be checked and
repaired before it is returned to the customer.
To determine the presence of high voltage, use an accurate
high impedance HV meter. Leakage Current Hot Check circuit
Adjust brightness, color, contrast controls to minimum. AC Volt-meter
Measure the high voltage.
The meter reading should indicate
23.5 1.5KV: 14-19 inch, 26 1.5KV: 19-21 inch,
29.0 1.5KV: 25-29 inch, 30.0 1.5KV: 32 inch
If the meter indication is out of tolerance, immediate service Good Earth Ground
and correction is required to prevent the possibility of such as WATER PIPE,
CONDUIT etc.
premature component failure. To Instrument's 0.15uF
exposed
METALLIC PARTS
1.5 Kohm/10W
CONTROL DESCRIPTIONS
All the functions can be controlled with the remote control handset.
Some functions can also be adjusted with the buttons on the front
panel of the set.
Remote control handset
POWER MUTE Before you use the remote control handset, please install the bat-
1 12 teries. See the next page.
1 2 3
1. POWER
4 5 6 switches the set on from standby or off to standby.
2 7 8 9
2. NUMBER BUTTONS
ARC 0 TV/AV
switches the set on from standby or directly select a number.
3 13
SOUND PICTURE MENU 3. ARC (Aspect Ratio Control)
4 14 changes the picture format.
T U R B O OK
4. TURBO PICTURE BUTTON / SOUND BUTTON (option)
PR selects Turbo picture.
VOL VOL
5
PR 5. D / E (Programme Up/Down)
REW PLAY FF
selects a programme or a menu item.
switches the set on from standby.
6 FAVOURITE STOP REC
scans programmes automatically.
F / G (Volume Up/Down)
21 adjusts the volume.
I/II SSM LIST adjusts menu settings.
15 OK
7
PSM SLEEP EYE/ 16 accepts your selection or displays the current mode.
8 17
9 MAIN STILL INDEX/ Q.VIEW
10 18 6. VCR BUTTONS
TEXT PIP
19 control a LG video cassette recorder.
11 20
MIX TIME REVEAL ? MODE M
7. I/II
SIZE STILL POSITION i selects the language during dual language broadcast.
selects the sound output (option).
PR PR SWAP INPUT
8. PSM (Picture Status Memory)
recalls your preferred picture setting.
9. SLEEP
sets the sleep timer.
10. MAIN STILL
freezes motion of the picture.
( With TELETEXT/PIP)
11. TELETEXT BUTTONS (option)
These buttons are used for teletext.
For further details, see the `Teletext' section.
12. MUTE
switches the sound on or off.
13. TV/AV
selects TV or AV mode.
switches the set on from standby.
14. MENU
selects a menu. POWER MUTE
1 12
15. LIST
1 2 3
displays the programme table.
4 5 6
16. SSM (Sound Status Memory)
recalls your preferred sound setting. 2 7 8 9
17. EYE/ (option)
*
switches the eye function on or off. 3
ARC 0 TV/AV
13
SOUND PICTURE MENU
18. Q.VIEW
4 14
returns to the previously viewed programme. T U R B O OK
19. INDEX/ (option)
*
switches DISPLAY on or off. VOL
PR
VOL
5
PR
20. PIP BUTTONS (option)
PIP REW PLAY FF
switches the sub picture on or off.
PR +/- 6 FAVOURITE STOP REC
selects a programme for the sub picture.
SWAP 21
alternates between main and sub picture. I/II SSM LIST
INPUT 15
7
selects the input mode for the sub picture. PSM SLEEP EYE/ 16
8 17
SIZE 9 MAIN STILL INDEX/ Q.VIEW
adjusts the sub picture size. 10 18
STILL TEXT
19
freezes motion of the sub picture. 11
MIX TIME REVEAL ? MODE M
POSITION
relocates the sub picture in clockwise direction. SIZE STILL POSITION i
9/4 PIP
switches on or off the 9 or 4 sub pictures.
21. FAVOURITE
selects a favorite programme.
* : No function
COLOURED BUTTONS : These buttons are used for teletext (only
TELETEXT models) or programme edit.
(With TELETEXT / Without PIP)
I/II SSM LIST
PSM SLEEP EYE/
MAIN STILL INDEX/ Q.VIEW
PIP
20
SIZE STILL POSITION
PR PR SWAP INPUT
(Without TELETEXT / With PIP)
Front panel
8
3
S-VIDEO
VIDEO
6
L/MONO AUDIO R
4
AV3
ON/OFF
1
Side panel
25 7
1. MAIN POWER (ON/OFF) 7. EYE (option)
switches the set on or off. adjusts picture according to the surrounding
conditions.
2. POWER/STANDBY INDICATOR
illuminates brightly when the set is in standby 8. HEADPHONE SOCKET (option)
mode. Connect the headphone plug to this socket.
dims when the set is switched on.
3. MENU
selects a menu.
4. OK
accepts your selection or displays the current
mode.
F / G (Volume Down/Up)
adjusts the volume.
adjusts menu settings.
D / E (Programme Up/Down)
selects a programme or a menu item.
switches the set on from standby.
5. REMOTE CONTROL SENSOR
6. AUDIO/VIDEO IN SOCKETS (AV3)
Connect the audio/video out sockets of
external equipment to these sockets.
S-VIDEO/AUDIO IN SOCKETS (S-AV)
Connect the video out socket of an S-VIDEO
VCR to the S-VIDEO socket.
Connect the audio out sockets of the S-
VIDEO VCR to the audio sockets as in AV3.
SPECIFICATIONS
Note : Specification and others are subject to change without notice for improvement.
A Scope A Test Condition
This specification can be applied to all the television related to 1) Temperature : 20