Text preview for : 7154_901_01A.pdf part of Keithley 7154 901 01A Keithley 71xx 7154_901_01A.pdf
Back to : 7154_901_01A.pdf | Home
Model 7154
2-Pole High Voltage Scanner Card
Instruction Manual
Contains Operating and Servicing Information
WARRANTY
Model 7154 2-Pole High Voltage
Scanner Card
instruction Manual
B 1988, Kcithlcy Instruments, Inc.
Test Instrumentation Croup
All rights reserved.
Cleveland, Ohio, U.S.A.
March 1988, First Printing
document Numhcr: 7154-901-01 Rev. A
SAFETY PRECAUTIONS
The following safety precautions should be observed before using this
product and any associated instrumentation. Although some instruments
and accessories would normally be used with non-hazardous voltages,
there are situations where hazardous conditions may be present.
This product is intended for use by qualified personnel who recognize
shock hazards and are familiar with the safety precaution8 required to
avoid possible injury. Read the operating information carefully before us-
ing the product.
Exercise extreme caution when a shock hazard is present. Lethal voltage
may be present on cable connector jacks or test fixtures. The American
National Standards Institute (ANSI) states that a shock hazard exists
when voltage levels greater than 30V RMS, 42.4V peak, or 60VDC are
present. A good safety practice is to expect that hazardous voltage is
present in any unknown circuit before measuring.
Before operating an instrument, make pure the line cord is connected to a
properly grounded power receptacle. Inspect the connecting cables, test
leads, and jumpers for possible wear, cracks, or breaks before each use.
For maximum safety, do not touch the product, test cables, or any other
instruments while power is applied to the circuit under test. ALWAYS re-
move power from the entire test system and discharge any capacitors be-
fore: connecting or disconnecting cables or jumpers, installing or
removing switching cards, or making internal changes, such as installing
or removing jumpers.
Do not touch any object that could provide a current path to the common
side of the circuit under test or power line (earth) ground. Always make
mcasurcmcnts with dry hands while standing on a dry, insulated surface
capable of withstanding the voltage being measured.
Do not exceed the maximum signal levels of the instruments and acces-
sories, as defined in the specifications and operating information, and as
shown on the instrument or test fixture rear panel, or switching card.
Do not connect switching cards directly to unlimited power circuits. They
arc intended to be used with impedance limited sources. NEVER connect
switching cards directly to AC main. When connecting sources to switch-
ing cards, install protective devices to limit fault current and voltage to
the card.
When fuses are used in a product, replace with same type and rating for
continued protection against fire hazard.
Chassis connections must only be used as shield connections for rneasur-
ing circuits, NOT as safety earth ground conncctionfi.
If you are using a test fixture, keep the lid closed while power is applied
to the device under test. Safe operation requires the use of a lid interlock.
If a @ screw is present on the test fixture, connect it to safety earth
ground using #18 AWG or larger wire.
The $ symbol on an instrument or accessory indicates that 1OOOV or
more may be present on the terminals. Refer to the product manual for de-
tailed operating information.
Instrumentation and accessories should not be connected to humans.
Maintenance should be performed by qualified service personnel. Before
performing any maintenance, disconncct the line cord and all test cables.
SPECIFICATIONS
CHANNELS PER CARD: 10.
CONTACT CONFIGURATION: Z-pole Form A with
user selectable shield or driven guard. Each pole is
fused using No. 38 AWG magnet wire.
CONNECTOR TYPE: Screw terminals, No. 16 AWG
maximum.
RELAY DRIVE CURRENT: 57mA per relay typical.
MAXIMUM SIGNAL LEVEL: 1lOOV peak, 0.5A nns
switched, 1.OA rms carry, 1OVA (resistive load only).
CONTACT LIFE: >lO"closures (cold switching); >5 x 10`
closures (at maximum signal levels).
CONTACT RESISTANCE: <2WmQ initial, 2n to rated
life.
CONTACT POTENTIAL: <35pV per contact pair with
copper leads.
ACTUATION TIME <2ms, exclusive of mainframe.
CHANNEL ISOLATION: >lO'"fl, INPUT ISOLATION:
Differential: >lOQ, c50pF.
Common Mode: >lOQ <150pF.
COMMON MODE VOLTAGE: 1lOOV peak.
OPERATING ENVIRONMENT: 0' to 50